W52P1J-17-R-0141_0001.pdf

AMENDMENT OF SOLICITATION/MODIFICATION OF CONTRACT 1. Contract ID Code Page Of

2. Amendment/Modification No.

3. Effective Date

4. Requisition/Purchase Req No.

5. Project No. (If applicable)

6. Issued By Code 7. Administered By (If other than Item 6) Code

8. Name And Address Of Contractor (No., Street, City, County, State and Zip Code)

9A. Amendment Of Solicitation No.

9B. Dated (See Item 11)

10A. Modification Of Contract/Order No.

10B. Dated (See Item 13) Code Facility Code

11. THIS ITEM ONLY APPLIES TO AMENDMENTS OF SOLICITATIONS

The above numbered solicitation is amended as set forth in item 14. The hour and date specified for receipt of Offers is extended, is not extended.

Offers must acknowledge receipt of this amendment prior to the hour and date specified in the solicitation or as amended by one of the following methods:

(a) By completing items 8 and 15, and returning ____________ copies of the amendments: (b) By acknowledging receipt of this amendment on each copy of the offer submitted; or (c) By separate letter or telegram which includes a reference to the solicitation and amendment numbers. FAILURE OF YOUR ACKNOWLEDGMENT TO BE RECEIVED AT THE PLACE DESIGNATED FOR THE RECEIPT OF OFFERS PRIOR TO THE HOUR AND DATE SPECIFIED MAY RESULT IN REJECTION OF YOUR OFFER. If by virtue of this amendment you desire to change an offer already submitted, such change may be made by telegram or letter, provided each telegram or letter makes reference to the solicitation and this amendment, and is received prior to the opening hour and date specified.

12. Accounting And Appropriation Data (If required)

13. THIS ITEM ONLY APPLIES TO MODIFICATIONS OF CONTRACTS/ORDERS

It Modifies The Contract/Order No. As Described In Item 14.

A. This Change Order is Issued Pursuant To: The Changes Set Forth In Item 14 Are Made In

The Contract/Order No. In Item 10A.

B. The Above Numbered Contract/Order Is Modified To Reflect The Administrative Changes (such as changes in paying office, appropriation data, etc.) Set

Forth In Item 14, Pursuant To The Authority of FAR 43.103(b).

C. This Supplemental Agreement Is Entered Into Pursuant To Authority Of:

D. Other (Specify type of modification and authority)

E. IMPORTANT: Contractor is not, is required to sign this document and return _______________ copies to the Issuing Office.

14. Description Of Amendment/Modification (Organized by UCF section headings, including solicitation/contract subject matter where feasible.)

Except as provided herein, all terms and conditions of the document referenced in item 9A or 10A, as heretofore changed, remains unchanged and in full force and effect.

15A. Name And Title Of Signer (Type or print)

16A. Name And Title Of Contracting Officer (Type or print)

15B. Contractor/Offeror 15C. Date Signed 16B. United States Of America 16C. Date Signed

By (Signature of person authorized to sign) (Signature of Contracting Officer)

NSN 7540-01-152-8070

PREVIOUS EDITIONS UNUSABLE

30-105-02 STANDARD FORM 30 (REV. 10-83)

Prescribed by GSA FAR (48 CFR) 53.243

SEE SCHEDULE

X

Fixed Price with EPA - Actual Costs

0001 2018DEC03

W52P1J

ARMY CONTRACTING COMMAND - RI

ROCK ISLAND, IL 61299-8000

BLDGS 60 & 62

BENJAMIN J. GILLEN

EMAIL: BENJAMIN.J.GILLEN.CIV@MAIL.MIL

W52P1J-17-R-0141

2018OCT31

X

X

/SIGNED/

2 signed

SEE SECOND PAGE FOR DESCRIPTION

1 35

CONTINUATION SHEET

Reference No. of Document Being Continued Page of

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

SECTION A - SUPPLEMENTAL INFORMATION

Buyer Name: BENJAMIN J. GILLEN

Buyer Office Symbol/Telephone Number: CCRC-AC/(309)782-4571

Type of Contract 1: Fixed Price with EPA - Established Prices

Kind of Contract: Supply Contracts and Priced Orders

*** End of Narrative A0000 ***

W52P1J-17-R-0141 / Amendment 0001

The purpose of this amendment is to effect the following changes to Request for Proposal (RFP) W52P1J-17-R-0141.

1. Revise Section D, Narrative D0001 - Packaging Requirements, to update the following DODIC nomenclatures as a result of revisions to

Attachment 0030 - Price Matrix - .50 Caliber Family:

DODIC NSN _____ ___

N/A 1305-01-596-7099

A552 1305-01-591-4851

A552 1305-01-662-6430

A555 1305-01-591-4838

A555 1305-01-658-2714

A557 1305-01-591-4857

A557 1305-01-658-2580

A607 1305-01-249-6888

A607 1305-01-671-9952

2. Replace clause 52.245-1, Government Property (JAN 2017) with 52.245-1, Government Property (JAN 2017) -- Alternate I (APR 2012).

3. Revise Section J, List of Attachments, as follows:

a. Provide Exhibit A - Contract Data Requirements List - Production Items and Exhibit B - Contract Data Requirements List - PWS.

b. Revise Attachment 0018 - PWS 18 - Facility Plans Strategies and Analyses to accurately reflect Army Regulation (AR) 420-1 in lieu of AR 420-10.

c. Revise Attachment 0021 - Ammunition Data Card component Listings to update DODIC nomenclatures as a result of revisions to

Attachment 0030 - Price Matrix - .50 Caliber Family

d. Revise the following attachments to update DODIC nomenclatures and revise formula calculations:

- Attachment 0030 - Price Matrix - .50 Caliber Family

- Attachment 0034 - FAT Price Matrix - .50 Caliber

- Attachment 0042 - Price Matrix (INDEMNIFIED) - .50 Caliber Family

4. Revise paragraph (c)(2) of FAR 52.204-8, Annual Representations and Certifications, to identify representations or certifications that are applicable to this solicitation.

5. Revise paragraph (d)(2) of DFARS 252.204-7007, Alternate A, Annual Representations and Certifications, to identify representations or certifications that are applicable to this solicitation.

6. Revise Section L, Narrative L0001 - Instructions to Offerors, as follows:

a. Revise paragraph A.7 as follows:

From: Each volume shall not exceed the following limitations. Pages shall be 8.5 inches x 11 inches; however, graphs, charts, tables ____ and diagrams may use oversized paper of 8.5 inches x 14 inches or 11 inches x 17 inches. Any other page sizes are not permitted. Text size shall be no less than 12 point font; however, graphs, charts, tables, and diagrams may use text size no less than 8 point font. All pages shall be numbered, contain at least a one inch margin, and utilize Times New Roman font. Pages printed on both sides, to include

8.5 x 14 and 11 x 17 will be counted as two pages.

To: Each volume shall not exceed the following limitations. Pages shall be 8.5 inches x 11 inches; however, graphs, charts, tables __ and diagrams may use oversized paper of 8.5 inches x 14 inches or 11 inches x 17 inches. Any other page sizes are not permitted. Text

2 35

W52P1J-17-R-0141

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

size shall be no less than 12 point font; however, graphs, charts, tables, and diagrams may use text size no less than 8 point font. All pages shall be numbered, contain at least a one inch margin, and utilize Times New Roman font for paragraphs of text and either Times ________________________________________

New Roman or Arial, except for Arial Narrow, for paragraph headings, graphs, charts, tables, spreadsheets, and diagrams. Pages printed_______________________________________________________________________________________________________________________ on both sides, to include 8.5 x 14 and 11 x 17 will be counted as two pages.

b. Revise paragraph 8 as follows:

From: Page Limitations: The Government will not read or evaluate pages exceeding the below prescribed page limitations. Excess pages ____ will be removed from the proposals. Page limitations do not include table of contents, cross reference matrices, section bookmarks/dividers, or indices. Cover letters, proposal introductions and executive summaries shall not exceed a total of five (5) pages combined for each volume and are not part of the overall page count. No material may be incorporated in the proposal by reference, attachment, appendix, videotape, audiotape or other electronic media as a means to circumvent the page limitation. No electronic video or audio material will be reviewed or considered in the evaluation. Files shall not contain classified data. The use of hyperlinks in proposals is prohibited.

To: Page Limitations: The Government will not read or evaluate pages exceeding the below prescribed page limitations. Excess pages __ will be removed from the proposals. Page limitations do not include table of contents, cross reference matrices, list of figures, list ______________________ of acronyms, section bookmarks/dividers, or indices. Cover letters, proposal introductions and executive summaries shall not exceed a____________ total of five (5) pages combined for each volume and are not part of the overall page count. No material may be incorporated in the proposal by reference, attachment, appendix, videotape, audiotape or other electronic media as a means to circumvent the page limitation. No electronic video or audio material will be reviewed or considered in the evaluation. Files shall not contain classified data. The use of hyperlinks in proposals is prohibited.

c. Revise paragraph 8.a as follows:

From: Volume 1, Production, shall not exceed 150 pages, inclusive of a limit of 30 oversized pages. The Supplier Letters of ____

Commitment, completed Attachment 0046 Component Suppliers Template, Integrated Master Schedule (IMS), and Process Maps for the five

DODIC examples (A080, AB73, AA11, AB79, and AA50), and resumes are excluded from the page count limit. For a joint venture (JV) or teaming approach, signed copies of proposed letters of intent and JV or teaming agreements are also excluded from the page count limit.

To: Volume 1, Production, shall not exceed 175 pages, inclusive of a limit of 40 oversized pages. The Supplier Letters of Commitment, __ ___ __ completed Attachment 0046 Component Suppliers Template, Integrated Master Schedule (IMS), and Process Maps for the five DODIC examples

(A080, AB73, AA11, AB79, and AA50), and resumes are excluded from the page count limit. For a joint venture (JV) or teaming approach, signed copies of proposed letters of intent and JV or teaming agreements are also excluded from the page count limit.

c. Revise Volume 4 - Price Factor Paragraph 2 as follows:

From: All prices for this acquisition shall be stated in current U.S. dollars. ____ _______

To: All prices for this acquisition shall be stated in U.S. dollars. __

7. There is no change to the proposal response date as a result of this amendment.

8. All other terms and conditions of solicitation W52P1J-17-R-0141 remain in full force and effect.

*** END OF NARRATIVE A0002 ***

3 35

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

SECTION D - PACKAGING AND MARKING

The following DODICs shall comply with the packaging requirements outlined below.

DODIC: N/A

NSN: 1305-01-155-5456

NOMEN: 5.56mm M855 Reference Round

DODIC: A059

NSN: 1305-01-155-5459

NOMEN: 5.56mm Ball M855 Clipped w/ Bandoleer

DODIC: A071

NSN: 1305-01-255-6276

NOMEN: 5.56mm Ball M193 Clipped

DODIC: A080

NSN: 1305-00-182-3217

NOMEN: 5.56mm Blank M200 Bulk Pack

DODIC: AB57

NSN: 1305-01-559-3333

NOMEN: 5.56mm Ball B855A1 Clipped w/ Bandoleer

DODIC: AB74

NSN: 1305-01-596-4436

NOMEN: 5.56mm Trace M856A1 Bulk

DODIC: AB77

NSN: 1305-01-598-0155

NOMEN: 5.56mm, Ball, M855A1 10-Ctgs/10 Round Clip

DODIC: AC04

NSN: 1305-01-640-9490

NOMEN: 5.56mm HPT

PACKAGING REQUIREMENTS

(a) Packaging shall be in accordance with 12551963, revision AY, dated 13 JUNE 2018.

(b) When lot numbering is required, no more than one lot shall be packaged in an outer shipping container.

(c) Marking shall be in accordance with 12551963, revision AY, dated 13 JUNE 2018. 2-D barcodes are require in accordance with

12999545, rev J, dated 26 Jan 2018.

(d) The following shall apply to drawing 12551963, revision AY, dated 13 JUNE 2018:

(e) PERFORMANCE ORIENTED PACKAGING (POP)

(1) Prior to shipment, the manufacturer shall make sure the container has been tested by a Government approved Performance

Oriented Packaging (POP) Test laboratory for compliance with POP requirements in accordance with Title 49 Code of Federal Regulation.

Test will be to a weight at least 10% greater than the actual gross weight to be marked on the tested container. POP marking shall not be applied to the container until verified by the Government. For multiyear contracts, the contractor shall re-perform POP testing at a certified test laboratory if: the initial POP test report expires before the end of the contract, or there is a change in container manufacturer or design of the exterior shipping container. No re-test is needed if all packaging was purchased during the period that the POP test was valid.

(f) EXCEPTION TO POP MARKINGS

(1) If the container is manufactured outside the USA, the contractor shall not apply the UN POP certification mark provided in this contract (if applicable). The contractor/container manufacturer (outside the USA) is responsible to perform the UN POP certification tests and apply the marking authorized by the Transportation Competent Authority of the country of manufacture.

(g) POP VERIFICATION

4 35

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

(1) In no case shall a container be shipped if the gross weight marked on the package is greater than the POP certified weight.

If the average gross weight of the packed containers (determined by weighing two representative samples and averaging the weight) is greater than the certified weight, container marking operations shall cease and the procuring activity shall be contacted immediately.

(h) HEAT TREAT WOOD QUALITY MARKING

(1)In accordance with the requirements of the International Standards for Phytosanitary Measures (ISPM) 15, the following commercial heat treatment process has been approved by the American Lumber Standards Committee (ALSC) and is required for all Wood

Packaging Material (WPM). Boxes/pallets and any wood used as inner packaging made of non-manufactured wood shall be heat-treated. All

WPM shall be constructed from heat treated (treated to 56 degrees Celsius -core temperature- for 30 minutes) lumber and certified by an agency accredited by the ALSC in accordance with Wood Packaging Material Policy and Wood Packaging Material Enforcement Regulations (see

URL: http://www.alsc.org ). The box/pallet manufacturer and the manufacturer of wood used as inner packaging shall ensure traceability to the original source of heat treatment.

(i) MARKING

(1) Each box/pallet shall be marked to show the conformance to the International Plant Protection Convention Standard. The quality mark shall be placed on both ends of the outer packaging, between the end cleats or end battens. Pallet markings shall be applied to the stringer or block on diagonally opposite sides or ends of the pallet and be contrasting and clearly visible. All dunnage lumber used in configuring and/or securing the load shall also comply with ISPM-15 and be marked with an ALSC approved dunnage stamp on opposite surfaces. Foreign manufacturers shall have the heat treatment and marking of non-manufactured wood products verified in accordance with the ISPM-15 compliance program.

(j) Palletization shall be in accordance with 19-48-4116/5, revision 19, dated MARCH 2018. 19-48-4116, Revision 13, dated Jan 2017, applies. This drawing is the basic palletization drawing called out in this contract. Marking shall be in accordance with ACV00561, Revision G, dated 26 Jan 2018. Wood Packaging Material (WPM) shall be in accordance with ACV00831, Dated: 01 MAR 2010. 2-D barcodes are required.

DODIC: A062

NSN: 1305-01-258-8692

NOMEN: 5.56mm Ball M855 Linked

DODIC: A075

NSN: 1305-01-258-8694

NOMEN: 5.56mm Blank M200 Linked

DODIC: AB56

NSN: 1305-01-559-3332

NOMEN: 5.56mm Ball M855A1 Linked

DODIC: AB73

NSN: 1305-01-596-4478

NOMEN: 5.56mm 4 Ball M855Al/1 Trace M856A1

DODIC: AB76

NSN: 1305-01-596-4391

NOMEN: 5.56mm 4 Ball M855/1 Trace M856A1

PACKAGING REQUIREMENTS

(a) Packaging shall be in accordance with 12590217, revision AN, dated 31 JAN 2018.

(b) When lot numbering is required, no more than one lot shall be packaged in an outer shipping container.

(c) Marking shall be in accordance with 12590217, revision AN, dated 31 JAN 2018. 2-D barcodes are require in accordance with

12999545, rev J, dated 26 Jan 2018.

(d) The following shall apply to drawing 12590217, revision AN, dated 31 JAN 2018:

(e) PERFORMANCE ORIENTED PACKAGING (POP)

(1) Prior to shipment, the manufacturer shall make sure the container has been tested by a Government approved Performance

Oriented Packaging (POP) Test laboratory for compliance with POP requirements in accordance with Title 49 Code of Federal Regulation.

5 35

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

Test will be to a weight at least 10% greater than the actual gross weight to be marked on the tested container. POP marking shall not be applied to the container until verified by the Government. For multiyear contracts, the contractor shall re-perform POP testing at a certified test laboratory if: the initial POP test report expires before the end of the contract, or there is a change in container manufacturer or design of the exterior shipping container. No re-test is needed if all packaging was purchased during the period that the POP test was valid.

(f) EXCEPTION TO POP MARKINGS

(1) If the container is manufactured outside the USA, the contractor shall not apply the UN POP certification mark provided in this contract (if applicable). The contractor/container manufacturer (outside the USA) is responsible to perform the UN POP certification tests and apply the marking authorized by the Transportation Competent Authority of the country of manufacture.

(g) POP VERIFICATION

(1) In no case shall a container be shipped if the gross weight marked on the package is greater than the POP certified weight.

If the average gross weight of the packed containers (determined by weighing two representative samples and averaging the weight) is greater than the certified weight, container marking operations shall cease and the procuring activity shall be contacted immediately.

(h) HEAT TREAT WOOD QUALITY MARKING

(1)In accordance with the requirements of the International Standards for Phytosanitary Measures (ISPM) 15, the following commercial heat treatment process has been approved by the American Lumber Standards Committee (ALSC) and is required for all Wood

Packaging Material (WPM). Boxes/pallets and any wood used as inner packaging made of non-manufactured wood shall be heat-treated. All

WPM shall be constructed from heat treated (treated to 56 degrees Celsius -core temperature- for 30 minutes) lumber and certified by an agency accredited by the ALSC in accordance with Wood Packaging Material Policy and Wood Packaging Material Enforcement Regulations (see

URL: http://www.alsc.org ). The box/pallet manufacturer and the manufacturer of wood used as inner packaging shall ensure traceability to the original source of heat treatment.

(i) MARKING

(1) Each box/pallet shall be marked to show the conformance to the International Plant Protection Convention Standard. The quality mark shall be placed on both ends of the outer packaging, between the end cleats or end battens. Pallet markings shall be applied to the stringer or block on diagonally opposite sides or ends of the pallet and be contrasting and clearly visible. All dunnage lumber used in configuring and/or securing the load shall also comply with ISPM-15 and be marked with an ALSC approved dunnage stamp on opposite surfaces. Foreign manufacturers shall have the heat treatment and marking of non-manufactured wood products verified in accordance with the ISPM-15 compliance program.

(j) Palletization shall be in accordance with 19-48-4116/5C, revision 9, dated AUG 2017. 19-48-4116, Revision 13, dated Jan 2017, applies. This drawing is the basic palletization drawing called out in this contract. Marking shall be in accordance with ACV00561, Revision G, dated 26 Jan 2018. Wood Packaging Material (WPM) shall be in accordance with ACV00831, Dated: 01 MAR 2010. 2-D barcodes are required.

DODIC: AB58

NSN: 1305-01-559-3335

NOMEN: 5.56mm Ball M855A1 Clipped (Comm Pack)

PACKAGING REQUIREMENTS

(a) Packaging shall be in accordance with 13014881, revision G, dated 7 May 2014.

(b) When lot numbering is required, no more than one lot shall be packaged in an outer shipping container.

(c) Marking shall be in accordance with 13014881, revision G, dated 7 May 2014. 2-D barcodes are require in accordance with

12999545, rev J, dated 26 Jan 2018.

(d) The following shall apply to drawing 13014881, revision G, dated 7 May 2014:

(e) PERFORMANCE ORIENTED PACKAGING (POP)

(1) Prior to shipment, the manufacturer shall make sure the container has been tested by a Government approved Performance

Oriented Packaging (POP) Test laboratory for compliance with POP requirements in accordance with Title 49 Code of Federal Regulation.

Test will be to a weight at least 10% greater than the actual gross weight to be marked on the tested container. POP marking shall not be applied to the container until verified by the Government. The POP test report shall be generated by the Manufacturer/Laboratory

6 35

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

following the test. The report must be kept on file by the contractor and submitted as required by the Contract Data Requirement List.

(DI-PACK-81059) For multiyear contracts, the contractor shall re-perform POP testing at a certified test laboratory if: the initial POP test report expires before the end of the contract, or there is a change in container manufacturer or design of the exterior shipping container. No re-test is needed if all packaging was purchased during the period that the POP test was valid.

(f) EXCEPTION TO POP MARKINGS

(1) If the container is manufactured outside the USA, the contractor shall not apply the UN POP certification mark provided in this contract (if applicable). The contractor/container manufacturer (outside the USA) is responsible to perform the UN POP certification tests and apply the marking authorized by the Transportation Competent Authority of the country of manufacture.

(g) POP VERIFICATION

(1) In no case shall a container be shipped if the gross weight marked on the package is greater than the POP certified weight.

If the average gross weight of the packed containers (determined by weighing two representative samples and averaging the weight) is greater than the certified weight, container marking operations shall cease and the procuring activity shall be contacted immediately.

(h) HEAT TREAT WOOD QUALITY MARKING

(1)In accordance with the requirements of the International Standards for Phytosanitary Measures (ISPM) 15, the following commercial heat treatment process has been approved by the American Lumber Standards Committee (ALSC) and is required for all Wood

Packaging Material (WPM). Boxes/pallets and any wood used as inner packaging made of non-manufactured wood shall be heat-treated. All

WPM shall be constructed from heat treated (treated to 56 degrees Celsius -core temperature- for 30 minutes) lumber and certified by an agency accredited by the ALSC in accordance with Wood Packaging Material Policy and Wood Packaging Material Enforcement Regulations (see

URL: http://www.alsc.org ). The box/pallet manufacturer and the manufacturer of wood used as inner packaging shall ensure traceability to the original source of heat treatment.

(i) MARKING

(1) Each box/pallet shall be marked to show the conformance to the International Plant Protection Convention Standard. The quality mark shall be placed on both ends of the outer packaging, between the end cleats or end battens. Pallet markings shall be applied to the stringer or block on diagonally opposite sides or ends of the pallet and be contrasting and clearly visible. All dunnage lumber used in configuring and/or securing the load shall also comply with ISPM-15 and be marked with an ALSC approved dunnage stamp on opposite surfaces. Foreign manufacturers shall have the heat treatment and marking of non-manufactured wood products verified in accordance with the ISPM-15 compliance program.

(j) Palletization shall be in accordance with 19-48-4357, revision 1, dated FEB 2018. Marking shall be in accordance with ACV00561, Revision G, dated 26 Jan 2018. Wood Packaging Material (WPM) shall be in accordance with ACV00831, Dated: 01 MAR 2010. 2-D barcodes are required.

DODIC: A111

NSN: 1305-01-181-1750

NOMEN: 7.62mm Blank M82 Lkd w/o Bandoleer

DODIC: A111

NSN: 1305-00-752-8087

NOMEN: 7.62mm Blank M82 Lkd w/ Bandoleer

DODIC: A129

NSN: 1305-00-580-0131

NOMEN: 7.62mm HPT M60

DODIC: A131

NSN: 1305-01-569-2912

NOMEN: 7.62mm 4 Ball M80/1 Trace M62 Lkd (Low Flash)

DODIC: A143

NSN: 1305-01-569-2917

NOMEN: 7.62mm Ball M80 Lkd (Low Flash), 100 cartridges/belt

DODIC: A146

NSN: 1305-00-892-2335

NOMEN: 7.62mm Trace M62 Lkd

7 35

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

DODIC: A151

NSN: 1305-00-889-2169

NOMEN: 7.62mm 4 Ball M80/1 Trace M62 Lkd (OHF)

DODIC: A159

NSN: 1305-00-926-4009

NOMEN: 7.62mm Dummy

DODIC: A255

NSN: 1305-01-380-9975

NOMEN: 7.62mm 4 Ball M80/1 Dim Trace M276

DODIC: AB72

NSN: 1305-01-596-1319

NOMEN: 7.62mm Blank M82A1 "Ceremonial" Bottlenose Blank

DODIC: AB79

NSN: 1305-01-598-5913

NOMEN: 7.62mm, Ball, M80A1 100 Crtg/ Belt

DODIC: AB85

NSN: 1305-01-606-7016

NOMEN: Ctg. 7.62mm Trace M62A1 Linked

DODIC: AB86

NSN: 1305-01-606-7003

NOMEN: 7.62mm M80A1 Linked 4:1 with M62A1

PACKAGING REQUIREMENTS

(a) Packaging shall be in accordance with 12960962 revision V, dated Jan 26, 2018.

(b) When lot numbering is required, no more than one lot shall be packaged in an outer shipping container.

(c) Marking shall be in accordance with 12960962, revision V, dated Jan 26, 2018. 2-D barcodes are require in accordance with

12999545, rev J, dated Jan 26, 2018.

(d) The following shall apply to drawing 12960962, revision V, dated Jan 26, 2018:

(e) PERFORMANCE ORIENTED PACKAGING (POP)

(1) Prior to shipment, the manufacturer shall make sure the container has been tested by a Government approved Performance

Oriented Packaging (POP) Test laboratory for compliance with POP requirements in accordance with Title 49 Code of Federal Regulation.

Test will be to a weight at least 10% greater than the actual gross weight to be marked on the tested container. POP marking shall not be applied to the container until verified by the Government. For multiyear contracts, the contractor shall re-perform POP testing at a certified test laboratory if: the initial POP test report expires before the end of the contract, or there is a change in container manufacturer or design of the exterior shipping container. No re-test is needed if all packaging was purchased during the period that the POP test was valid.

(f) EXCEPTION TO POP MARKINGS

(1) If the container is manufactured outside the USA, the contractor shall not apply the UN POP certification mark provided in this contract (if applicable). The contractor/container manufacturer (outside the USA) is responsible to perform the UN POP certification tests and apply the marking authorized by the Transportation Competent Authority of the country of manufacture.

(g) POP VERIFICATION

(1) In no case shall a container be shipped if the gross weight marked on the package is greater than the POP certified weight.

If the average gross weight of the packed containers (determined by weighing two representative samples and averaging the weight) is greater than the certified weight, container marking operations shall cease and the procuring activity shall be contacted immediately.

(h) HEAT TREAT WOOD QUALITY MARKING

(1)In accordance with the requirements of the International Standards for Phytosanitary Measures (ISPM) 15, the following

8 35

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

commercial heat treatment process has been approved by the American Lumber Standards Committee (ALSC) and is required for all Wood

Packaging Material (WPM). Boxes/pallets and any wood used as inner packaging made of non-manufactured wood shall be heat-treated. All

WPM shall be constructed from heat treated (treated to 56 degrees Celsius -core temperature- for 30 minutes) lumber and certified by an agency accredited by the ALSC in accordance with Wood Packaging Material Policy and Wood Packaging Material Enforcement Regulations (see

URL: http://www.alsc.org ). The box/pallet manufacturer and the manufacturer of wood used as inner packaging shall ensure traceability to the original source of heat treatment.

(i) MARKING

(1) Each box/pallet shall be marked to show the conformance to the International Plant Protection Convention Standard. The quality mark shall be placed on both ends of the outer packaging, between the end cleats or end battens. Pallet markings shall be applied to the stringer or block on diagonally opposite sides or ends of the pallet and be contrasting and clearly visible. All dunnage lumber used in configuring and/or securing the load shall also comply with ISPM-15 and be marked with an ALSC approved dunnage stamp on opposite surfaces. Foreign manufacturers shall have the heat treatment and marking of non-manufactured wood products verified in accordance with the ISPM-15 compliance program.

(j) Palletization shall be in accordance with 19-48-4116/7, revision 11, dated Aug 2016. 19-48-4116, Revision 13, dated Jan 2017, applies. This drawing is the basic palletization drawing called out in this contract. Marking shall be in accordance with ACV00561, Revision G, dated 26 Jan 2018. Wood Packaging Material (WPM) shall be in accordance with ACV00831, Dated: 01 MAR 2010. 2-D barcodes are required.

DODIC: A112

NSN: 1305-00-990-5594

NOMEN: 7.62mm Blank M82 Single Rd

DODIC: A122

NSN: 1305-01-586-0305

NOMEN: 7.62mm Ball M80 Single Rd

DODIC: A130

NSN: 1305-01-569-2891

NOMEN: 7.62mm Ball M80 Clipped (Low Flash)

DODIC: A140

NSN: 1305-00-926-4017

NOMEN: 7.62mm Trace M62 Single Rd

DODIC: A150

NSN: 1305-00-782-5831

NOMEN: 7.62mm M80 Reference Round

DODIC: A257

NSN: 1305-01-380-9803

NOMEN: 7.62mm 9 Ball M80/1 Dim Trace M276

DODIC: AA11

NSN: 1305-01-419-8202

NOMEN: 7.62mm M118 Long Range

DODIC: AB80

NSN: 1305-01-598-5898

NOMEN: 7.62mm, Ball, M80A1 5-Crtg/5 Round Clip

DODIC: AB81

NSN: 1305-01-598-5928

NOMEN: 7.62mm, Ball, M80A1 750-Crtg/Belt

DODIC: AB82

NSN: 1305-01-598-8201

NOMEN: 7.62mm, Ball, M80A1 20-Crtg/Carton

DODIC: AB84

NSN: 1305-01-606-7081

9 35

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

NOMEN: Ctg. 7.62mm Trace M62A1: Packed 20-CTG/CARTON

PACKAGING REQUIREMENTS

(a) Packaging shall be in accordance with 9362607, revision AD, dated 26 AUG 2014.

(b) When lot numbering is required, no more than one lot shall be packaged in an outer shipping container.

(c) Marking shall be in accordance with 9362607, revision AD, dated 26 AUG 2014. 2-D barcodes are require in accordance with

12999545, rev J, dated 26 Jan 2018.

(d) The following shall apply to drawing 9362607, revision AD, dated 26 AUG 2014:

(e) PERFORMANCE ORIENTED PACKAGING (POP)

(1) Prior to shipment, the manufacturer shall make sure the container has been tested by a Government approved Performance

Oriented Packaging (POP) Test laboratory for compliance with POP requirements in accordance with Title 49 Code of Federal Regulation.

Test will be to a weight at least 10% greater than the actual gross weight to be marked on the tested container. POP marking shall not be applied to the container until verified by the Government. For multiyear contracts, the contractor shall re-perform POP testing at a certified test laboratory if: the initial POP test report expires before the end of the contract, or there is a change in container manufacturer or design of the exterior shipping container. No re-test is needed if all packaging was purchased during the period that the POP test was valid.

(f) EXCEPTION TO POP MARKINGS

(1) If the container is manufactured outside the USA, the contractor shall not apply the UN POP certification mark provided in this contract (if applicable). The contractor/container manufacturer (outside the USA) is responsible to perform the UN POP certification tests and apply the marking authorized by the Transportation Competent Authority of the country of manufacture.

(g) POP VERIFICATION

(1) In no case shall a container be shipped if the gross weight marked on the package is greater than the POP certified weight.

If the average gross weight of the packed containers (determined by weighing two representative samples and averaging the weight) is greater than the certified weight, container marking operations shall cease and the procuring activity shall be contacted immediately.

(h) HEAT TREAT WOOD QUALITY MARKING

(1)In accordance with the requirements of the International Standards for Phytosanitary Measures (ISPM) 15, the following commercial heat treatment process has been approved by the American Lumber Standards Committee (ALSC) and is required for all Wood

Packaging Material (WPM). Boxes/pallets and any wood used as inner packaging made of non-manufactured wood shall be heat-treated. All

WPM shall be constructed from heat treated (treated to 56 degrees Celsius -core temperature- for 30 minutes) lumber and certified by an agency accredited by the ALSC in accordance with Wood Packaging Material Policy and Wood Packaging Material Enforcement Regulations (see

URL: http://www.alsc.org ). The box/pallet manufacturer and the manufacturer of wood used as inner packaging shall ensure traceability to the original source of heat treatment.

(i) MARKING

(1) Each box/pallet shall be marked to show the conformance to the International Plant Protection Convention Standard. The quality mark shall be placed on both ends of the outer packaging, between the end cleats or end battens. Pallet markings shall be applied to the stringer or block on diagonally opposite sides or ends of the pallet and be contrasting and clearly visible. All dunnage lumber used in configuring and/or securing the load shall also comply with ISPM-15 and be marked with an ALSC approved dunnage stamp on opposite surfaces. Foreign manufacturers shall have the heat treatment and marking of non-manufactured wood products verified in accordance with the ISPM-15 compliance program.

(j) Palletization shall be in accordance with 19-48-4116/7B, revision 1, dated FEB 2014. 19-48-4116, Revision 13, dated Jan 2017, applies. This drawing is the basic palletization drawing called out in this contract. Marking shall be in accordance with ACV00561, Revision G, dated 26 Jan 2018. Wood Packaging Material (WPM) shall be in accordance with ACV00831, Dated: 01 MAR 2010. 2-D barcodes are required.

DODIC: A164

NSN: 1305-01-569-2925

NOMEN: 7.62mm Ball M80 Lkd (Low Flash), 750-Ctg/Belt

10 35

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

DODIC: A165

NSN: 1305-01-569-2929

NOMEN: 7.62mm 4 Ball M80/1 Trace M62 Lkd f/Minigun (Low Flash)

DODIC: A168

NSN: 1305-01-569-2932

NOMEN: 7.62mm 9 Ball M80/1 Trace M62 Lkd (Low Flash)

DODIC: AB88

NSN: 1305-01-606-7063

NOMEN: Cartridge, 7.62mm, Ball, M80A1 and Tracer, M62A1, Lkd (4:1)

DODIC: AB89

NSN: 1305-01-606-6538

NOMEN: Cartridge, 7.62mm, Ball, M80A1 and Tracer, M62A1, Lkd (9:1)

PACKAGING REQUIREMENTS

(a) Packaging shall be in accordance with 10535781, revision AG, dated 19 JAN 2018.

(b) When lot numbering is required, no more than one lot shall be packaged in an outer shipping container.

(c) Marking shall be in accordance with 10535781, revision AG, dated 19 JAN 2018. 2-D barcodes are require in accordance with

12999545, rev J, dated 26 Jan 2018.

(d) The following shall apply to drawing 10535781, revision AG, dated 19 JAN 2018:

(e) PERFORMANCE ORIENTED PACKAGING (POP)

(1) Prior to shipment, the manufacturer shall make sure the container has been tested by a Government approved Performance

Oriented Packaging (POP) Test laboratory for compliance with POP requirements in accordance with Title 49 Code of Federal Regulation.

Test will be to a weight at least 10% greater than the actual gross weight to be marked on the tested container. POP marking shall not be applied to the container until verified by the Government. For multiyear contracts, the contractor shall re-perform POP testing at a certified test laboratory if: the initial POP test report expires before the end of the contract, or there is a change in container manufacturer or design of the exterior shipping container. No re-test is needed if all packaging was purchased during the period that the POP test was valid.

(f) EXCEPTION TO POP MARKINGS

(1) If the container is manufactured outside the USA, the contractor shall not apply the UN POP certification mark provided in this contract (if applicable). The contractor/container manufacturer (outside the USA) is responsible to perform the UN POP certification tests and apply the marking authorized by the Transportation Competent Authority of the country of manufacture.

(g) POP VERIFICATION

(1) In no case shall a container be shipped if the gross weight marked on the package is greater than the POP certified weight.

If the average gross weight of the packed containers (determined by weighing two representative samples and averaging the weight) is greater than the certified weight, container marking operations shall cease and the procuring activity shall be contacted immediately.

(h) HEAT TREAT WOOD QUALITY MARKING

(1)In accordance with the requirements of the International Standards for Phytosanitary Measures (ISPM) 15, the following commercial heat treatment process has been approved by the American Lumber Standards Committee (ALSC) and is required for all Wood

Packaging Material (WPM). Boxes/pallets and any wood used as inner packaging made of non-manufactured wood shall be heat-treated. All

WPM shall be constructed from heat treated (treated to 56 degrees Celsius -core temperature- for 30 minutes) lumber and certified by an agency accredited by the ALSC in accordance with Wood Packaging Material Policy and Wood Packaging Material Enforcement Regulations (see

URL: http://www.alsc.or g). The box/pallet manufacturer and the manufacturer of wood used as inner packaging shall ensure traceability to the original source of heat treatment.

(i) MARKING

(1) Each box/pallet shall be marked to show the conformance to the International Plant Protection Convention Standard. The quality mark shall be placed on both ends of the outer packaging, between the end cleats or end battens. Pallet markings shall be applied to the stringer or block on diagonally opposite sides or ends of the pallet and be contrasting and clearly visible. All dunnage lumber used in configuring and/or securing the load shall also comply with ISPM-15 and be marked with an ALSC approved dunnage stamp on opposite

11 35

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

surfaces. Foreign manufacturers shall have the heat treatment and marking of non-manufactured wood products verified in accordance with the ISPM-15 compliance program.

(j) Palletization shall be in accordance with 19-48-4116/7D, revision 06, dated 01 MAY 2015. 19-48-4116, Revision 13, dated Jan 2017, applies. This drawing is the basic palletization drawing called out in this contract. Marking shall be in accordance with ACV00561, Revision G, dated 26 Jan 2018. Wood Packaging Material (WPM) shall be in accordance with ACV00831, Dated: 01 MAR 2010. 2-D barcodes are required.

DODIC: N/A

NSN: 1305-01-596-7099

NOMEN: Cal .50 Reference Round - Lead Free (SMP860)

DODIC: N/A

NSN: 1305-01-672-8613

NOMEN: Cal .50 Reference Round (SMP860)

DODIC: A531

NSN: 1305-01-659-2220

NOMEN: Cal .50 API M8 Single Rd (SMP860)

DODIC: A541

NSN: 1305-01-659-2417

NOMEN: Cal .50 APIT M20 Single Rd (SMP860)

DODIC: A552

NSN: 1305-01-591-4851

NOMEN: Cal .50 Ball M33A1 Single Rd - Lead Free (SMP860)

DODIC: A552

NSN: 1305-01-662-6430

NOMEN: Cal .50 Ball M33 Single Rd (SMP860)

DODIC: A555

NSN: 1305-01-591-4838

NOMEN: Cal .50 Ball M33A1 Lkd - Lead Free (SMP860)

DODIC: A555

NSN: 1305-01-658-2714

NOMEN: Cal .50 Ball M33 Lkd - (SMP860)

DODIC: A557

NSN: 1305-01-591-4857

NOMEN: Cal .50 4 Ball M33A1/1 Trace M17 Lkd - Lead Free (SMP860)

DODIC: A557

NSN: 1305-01-658-2580

NOMEN: Cal .50 4 Ball M33/1 Trace M17 Lkd - (SMP860)

DODIC: A575

NSN: 1305-01-557-2988

NOMEN: Cal .50 HPT M1 Single Rd

DODIC: A576

NSN: 1305-01-659-2421

NOMEN: Cal .50 4 API M8/1 APIT M20 Lkd (SMP860)

DODIC: A585

NSN: 1305-01-659-2202

NOMEN: Cal .50 APIT M20 Lkd

DODIC: A598

NSN: 1305-01-078-4879

NOMEN: Cal .50 Blank M1A1 Lkd

12 35

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

DODIC: A606

NSN: 1305-01-250-8162

NOMEN: Cal .50 API MK211-0 Single Rd

DODIC: A606

NSN: 1305-01-671-6605

NOMEN: Cal .50 API MK211-0 Single Rd (SMP860)

DODIC: A607

NSN: 1305-01-249-6888

NOMEN: Cal .50 4 API MK211-1/APIT M20

DODIC: A607

NSN: 1305-01-671-9952

NOMEN: Cal .50 4 API MK211-1/APIT M20 (SMP860)

DODIC: AA06

NSN: 1305-01-473-4774

NOMEN: Cal .50 2 API MK211, Mod 1/2AP MK263, Mod 0/1 APIT M20

DODIC: AA06

NSN: 1305-01-671-9944

NOMEN: Cal .50 2 API MK211, Mod 1/2AP MK263, Mod 0/1 APIT M20 (SMP860)

DODIC: AA41

NSN: 1305-01-464-2541

NOMEN: Cal .50 API MK211 Mod 1 Single Rd

DODIC: AA41

NSN: 1305-01-671-6603

NOMEN: Cal .50 API MK211 Mod 1 Single Rd (SMP860)

DODIC: AA42

NSN: 1305-01-464-3218

NOMEN: Cal .50 API-DT MK257 Mod 0 Single Rd

DODIC: AA42

NSN: 1305-01-671-6579

NOMEN: Cal .50 API-DT MK257 Mod 0 Single Rd (SMP860)

DODIC: AA50

NSN: 1305-01-473-4766

NOMEN: Cal .50 2 API MK211, Mod 1/2AP MK263, Mod 0/1 API-DT MK257

DODIC: AA50

NSN: 1305-01-671-9946

NOMEN: Cal .50 2 API MK211, Mod 1/2AP MK263, Mod 0/1 API-DT MK257 (SMP860)

DODIC: AA58

NSN: 1305-01-482-1053

NOMEN: Cal .50 AP MK263 Mod 0 Single Rd

DODIC: AA58

NSN: 1305-01-671-6602

NOMEN: Cal .50 AP MK263 Mod 0 Single Rd (SMP860)

DODIC: AB30

NSN: 1305-01-543-0850

NOMEN: Cal .50 4 API M8/1 API-DT MK257

PACKAGING REQUIREMENTS

(a) Packaging shall be in accordance with 12576456, revision AY, dated 13 JULY 2018.

13 35

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

(b) When lot numbering is required, no more than one lot shall be packaged in an outer shipping container.

(c) Marking shall be in accordance with 12576456, revision AY, dated 13 JULY 2018. 2-D barcodes are require in accordance with

12999545, rev J, dated 26 Jan 2018.

(d) The following shall apply to drawing 12576456, revision AY, dated 13 JULY 2018:

(e) PERFORMANCE ORIENTED PACKAGING (POP)

(1) Prior to shipment, the manufacturer shall make sure the container has been tested by a Government approved Performance

Oriented Packaging (POP) Test laboratory for compliance with POP requirements in accordance with Title 49 Code of Federal Regulation.

Test will be to a weight at least 10% greater than the actual gross weight to be marked on the tested container. POP marking shall not be applied to the container until verified by the Government. For multiyear contracts, the contractor shall re-perform POP testing at a certified test laboratory if: the initial POP test report expires before the end of the contract, or there is a change in container manufacturer or design of the exterior shipping container. No re-test is needed if all packaging was purchased during the period that the POP test was valid.

(f) EXCEPTION TO POP MARKINGS

(1) If the container is manufactured outside the USA, the contractor shall not apply the UN POP certification mark provided in this contract (if applicable). The contractor/container manufacturer (outside the USA) is responsible to perform the UN POP certification tests and apply the marking authorized by the Transportation Competent Authority of the country of manufacture.

(g) POP VERIFICATION

(1) In no case shall a container be shipped if the gross weight marked on the package is greater than the POP certified weight.

If the average gross weight of the packed containers (determined by weighing two representative samples and averaging the weight) is greater than the certified weight, container marking operations shall cease and the procuring activity shall be contacted immediately.

(h) HEAT TREAT WOOD QUALITY MARKING

(1)In accordance with the requirements of the International Standards for Phytosanitary Measures (ISPM) 15, the following commercial heat treatment process has been approved by the American Lumber Standards Committee (ALSC) and is required for all Wood

Packaging Material (WPM). Boxes/pallets and any wood used as inner packaging made of non-manufactured wood shall be heat-treated. All

WPM shall be constructed from heat treated (treated to 56 degrees Celsius -core temperature- for 30 minutes) lumber and certified by an agency accredited by the ALSC in accordance with Wood Packaging Material Policy and Wood Packaging Material Enforcement Regulations (see

URL: http://www.alsc.org ). The box/pallet manufacturer and the manufacturer of wood used as inner packaging shall ensure traceability to the original source of heat treatment.

(i) MARKING

(1) Each box/pallet shall be marked to show the conformance to the International Plant Protection Convention Standard. The quality mark shall be placed on both ends of the outer packaging, between the end cleats or end battens. Pallet markings shall be applied to the stringer or block on diagonally opposite sides or ends of the pallet and be contrasting and clearly visible. All dunnage lumber used in configuring and/or securing the load shall also comply with ISPM-15 and be marked with an ALSC approved dunnage stamp on opposite surfaces. Foreign manufacturers shall have the heat treatment and marking of non-manufactured wood products verified in accordance with the ISPM-15 compliance program.

(j) Palletization shall be in accordance with 19-48-4116/14, revision 17, dated 01 NOV 2016. 19-48-4116, Revision 13, dated Jan 2017, applies. This drawing is the basic palletization drawing called out in this contract. Marking shall be in accordance with ACV00561, Revision F, dated 02 DEC 2008. Wood Packaging Material (WPM) shall be in accordance with ACV00831, Dated: 01 MAR 2010. 2-D barcodes are required.

DODIC: AB30

NSN: 1305-01-673-1262

NOMEN: Cal .50 4 API M8/1 API-DT MK257 (SMP860)

DODIC: A091

NSN: 1305-01-255-9109

NOMEN: CTG CAL 22 LONG RANGE MATCH

COMMERCIAL PACKAGING REQUIREMENTS

(a) Packaging - Preservation, packaging, packing, unitization and marking furnished by the supplier shall provide protection for a

14 35

Name of Offeror or Contractor:

PIIN/SIIN MOD/AMD

minimum of one year, provide for multiple handling, redistribution and shipment by any mode and meet or exceed the following requirements.

(1) Cleanliness - Items shall be free of dirt and other contaminants which would contribute to the deterioration of the item or which would require cleaning by the customer prior to use. Coatings and preservatives applied to the item for protection are not considered contaminants.

(2) Preservation - Items susceptible to corrosion or deterioration shall be provided protection such as preservative coatings, volatile corrosion inhibitors, desiccants, water-proof and/or water-vapor-proof barriers.

(3) Cushioning - Items requiring protection from physical and mechanical damage (e.g. fragile, sensitive, critical material) or which could cause physical damage to other items, shall be protected by wrapping, cushioning, pack compartmentalization, or other means to mitigate shock and vibration and prevent damage during handling and shipment.

(b)Packing

(1) Unit packages and intermediate packages meeting the requirements for a shipping container may be utilized as shipping containers. All shipping containers shall be the most cost effective and shall be of the minimum cube to contain and protect the items.

A unit package shall be so designed and constructed that it will contain the contents with no damage to the item(s), and with minimal damage to the unit pack during shipment and storage in the shipping container, and will allow subsequent handling.

(2) Bulk Packaging Items packaged directly in shipping containers shall be separated with pads, liners, partitions or dividers as required to protect the items, strengthen the container and to distribute the load.

(3) Unit Package Quantity - Unless otherwise specified, the unit package quantity shall be one each part, set, assembly, kit, etc.

(4) Shipping Containers - The shipping container (including any necessary blocking, bracing, cushioning, or waterproofing) shall comply with the regulations of the carrier used and shall provide safe delivery to the destination at the lowest tariff cost. The shipping container shall be capable of multiple handling, stacking at least ten feet high, and storage under favorable conditions (such as enclosed facilities) for a minimum of one year.

(c) Unitization

(1) Shipments of identical items going to the same destination shall be palletized if they have a total cubic displacement of 50 cubic feet or more unless skids or other forklift handling features are included on the containers. Pallet loads must be stable, and to the greatest extent possible, provide a level top for ease of stacking. A palletized load shall be of a size to allow for placement of two loads high and wide in a conveyance. The weight capacity of the pallet must be adequate for the load. The preferred commercial expendable pallet is a 40 x 48 inch, 4-way entry pallet although variations may be permitted as dictated by the characteristics of the items being unitized. The load shall be contained in a manner that will permit safe handling during shipment and storage.

(d) Marking

(1) All unit packages, intermediate packs, exterior shipping containers, and, as applicable, unitized loads shall be marked in accordance with MIL-STD-129, Revision R, Date 18 February 2014 including 2D bar coding on outer shipping container and the unitized load. The contractor is responsible for application of special markings as discussed in the Military Standard regardless of whether specified in the contract or not. Special markings include, but are not limited to, shelf-life markings, structural markings, and transportation special handling markings.

(e)Hazardous Materials

(1) A hazardous material is defined as a substance which has been determined by the Department of Transportation to be capable of posing an unreasonable risk to health, safety, and property when transported in commerce and which has been so designated. (This includes all items listed as hazardous in Title 49 CFR and other applicable modal regulations effective at the time of shipment.)

Ammunition and explosives (Hazard Class 1) are special cases and must be properly hazard classified and registered with the competent authority of the United States (Department of Transportation).

(2)…