Attachment_2_Raytheon_Ktech_Telemetry_System_(RTMS)_Capabilities_Interface_Reference_Document__(IRD).pdf

MSW (Rev 06-24-2004) Page 1 of 4

AIRCRAFT MODIFICATION REQUEST REQUEST NUMBER

DATE SUBMITTED

FROM

CODE

E

TELEPHONE NUMBER

AIRCRAFT (TYPE / MODEL / SERIES)

C-130

TO

MOD TITLE

C-130 TM System

BUNO / MODEX

PROPOSAL ABSTRACT

This modification will install the Telemetry (TM) Antenna, Pedestal and Mounting Plate in the nose of the C-130 & an Operator Pallet in the cargo bay. The following NAVPASS AMR SERNOs were previously installed and will be incorporated under this AMR SERNO.

See ENCL (1).

VX-30-2012-00050A [FLT CLNC 042004Z DEC 2013] -- all wiring, circuit breakers VX-30-2012-00050B [FLT CLNC 042003Z DEC 2013] -- Doubler at Pressure Bulkhead & FS-245 Disconnect Panel VX-30-2012-00050C [FLT CLNC 202009 DEC 2012] -- Overhead Disconnect Panel VX-30-2012-00050D [FLT CLNC 202009 DEC 2012] -- GPS/Iridium Antennas on Roof of Acft VX-30-2012-00050E [FLT CLNC 202009 DEC 2012] -- L-Band Antennas on Belly of Acft

TECHNICAL POC

CODE

PHONE

REQUESTED B

TITLE

DATE

ROUTING / REVIEW

REVIEWERS CODE SIGNATURE SAT UNSAT DATE STRUCTURAL ADEQUANCY

ANALYSYIS REQUIRED FOR

MOD APPROVAL?

ANALYSIS MEMO

SER. NO./DATE

YES

NO

ANALYSYIS REQUIRED FOR

MOD APPROVAL?

ANALYSIS MEMO

SER. NO./DATE

EMC/EMI/HERO/SOF

ANALYSYIS REQUIRED FOR

MOD APPROVAL?

ANALYSIS MEMO

SER. NO./DATE

REVIEWERS’ REMARKS

AUTHORIZED TO PROCEED

APPROVED DISAPPROVED

MOD APPROVAL AUTHORITY SIGNATURE DATE:

APPROVERS’ REMARKS

FLIGHT CLEARANCE REQUEST IS VIA e.POWER.

MSW (Rev 06-24-2004) Page 2 of 4

AIRCRAFT MODIFICATION REQUEST AIRCRAFT

BUNO

REQUEST NO

AERONAUTICAL SYSTEMS MODIFICATION DATA – GENERAL DESCRIPTION

DETAIL DESCRIPTION OF AERONAUTICAL SYSTEM MODIFICATION AND

EQUIPMENT INSTALLATION

JOB ORDER NUMBER

ASSOCIATED

DRAWINGS

LISTING:

ENCL (1): Aircraft Layout ENCL (2): TM Antenna (Dwg & Photos) ENCL (3): Operator Pallet (Photos) ENCL (4): Previously Installed Items (Photos) ENCL (5): TM Functional & Electrical Dwgs ENCL (6): Electrical Loads Calculations ENCL (7): Weight & Balance info ENCL (8): Structural Analysis of TM Antenna – separate document in NAVPASS

ENCL (9): Structural Analysis of TM Operator Pallet – separate document in NAVPASS ENCL (10): MIL-704A Safe for Flight Tests ENCL (11): Horizontal & Vertical Cable Support Bars Dwg

This modification on the C-130 is intended as a backup TM receive system to the NP-3D Billboard TM system. The TM system on the NP-3D consists of a phase arrayed system with 5-beams while the C-130 system is a mechanically steered system consisting of a single beam. GPS data is received by the acft, while Iridium data, Iridium voice and L-band data is transmitted from the acft.

The TM antenna is designed to rotate +/- 60-degrees in both elevation and azimuth However, due to interference with the aircraft structure the antenna rotation is restricted to +40/-7-degrees in elevation and +/- 35-degrees in azimuth via preset software stops. The TM antenna mounting plate will be secured by two support arms which utilize the same fastener locations as the APS-115 antenna.

See ENCL (2).

The TM Operator Pallet consists of a Knight Aerospace pallet (identical to the Hairy Buffalo pallet) with (3) Platform Systems racks and (2) standard P-3 crew seats. The racks are installed with the operator facing FWD in the cargo bay area. See ENCL (3) for more details.

In order to install the TM antenna in the acft nose the existing APS-115 RADAR antenna & bracket must be removed.

The APS-115 Operator Pallet, if installed, must be removed to accommodate the installation of the TM Operator Pallet.

EMC: EMC SOF test will be completed as required.

HUMAN SYSTEM: EGRESS -- there’s approximately 30” of space between Rack 3 and the port side of the acft. See ENCL (3).

ELECTRICAL POWER: Power for the Operator Pallet is obtained from the DASC Power Panel. A new ckt brkr was installed. See ENCL (5). A partial MIL-704A test was successfully completed to address Safe for Flight issues.

ENCL (10).

STRUCTURES: Analyses were completed of the TM Antenna assembly and of the TM Operator Pallet. Due to the size of the structural analyses of both the TM Antenna assembly and the Operator Pallet the analyses [ENCLs (8) & (9)] can be found in NAVPASS under SERNO VX-30-2013-00060 in the Documents Tab.

RADAR & ANTENNA SYSTEM: See ENCL (2). Telemetry (TM) receive system only. L-band transmitter is the same system used on VX-30 NP-3D.

MSW (Rev 06-24-2004) Page 3 of 4

AIRCRAFT

BUNO/NALC

REQUEST NUMBER

POST-INSTALLATION DEVIATION DESCRIPTION

AMENDMENT

YES NO

DATE INSTALLED

QA VERIFIED (Signature)

REMARKS

PRIOR REQ/FLT CLNCS

MSW (Rev 06-24-2004) Page 4 of 4

AIRCRAFT MODIFICATION REQUEST AIRCRAFT

BUNO

REQUEST NO

REMOVE INSTALL EQUIPMENT TO BE REMOVED/INSTALLED WT APPROX CG POSITIONS IN A/C

LONGITUDINAL

COORDINATES

X APS-115 RADAR Antenna & Bracket 104-lbs 93 X TM Antenna & mounting assembly 122-lbs 93

X TM Operator Pallet 1862-lbs 304.5

PROJECT INSTALLATION WEIGHT AND BALANCE A/C WEIGHING REQUIRED YES NO

AIRCRAFT /STORE ALLOWABLE CENTER OF GRAVITY (%MAC) AS MODIFIED CENTER OF GRAVITY (%MAC) YES NO N/A

DATE GENERATED NATOPS CG LIMITS

FWD – AFT (%MAC)

TAKEOFF CR CONFIG FULL INTERNAL CG: TAKEOFF CR CONFIG FULL INTERNAL CG:

TAKEOFF PA CONFIG FULL INTERNAL CG: TAKEOFF PA CONFIG FULL INTERNAL CG:

LANDING CR CONFIG MIN FUEL CG: LANDING CR CONFIG MIN FUEL CG: CONFIGS ATTACHED

LANDING PA CONFIG MIN FUEL CG: LANDING PA CONFIG MIN FUEL CG:

COMPUTED / REVIEWED BY CODE PHONE DATE

roy.sakamoto Typewritten Text

ENCL (1)

Aircraft Layout roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text

ENCL (2)

TM Antenna (Dwgs & Photos) roy.sakamoto Typewritten Text

Support Arm (turqoise)

Mounting Plate Antenna Pedestal

TM Antenna

VX-30-2013-00060

(TM Antenna)

Long Angles on front of Mounting Plate

Short Angles on back of Mounting Plate

Existing APS-115 mounting channel (olive green)

TM Antenna, Pedestal & Mounting Plate (secured to a rack for photo purposes only)

Gray styrofoam simulates the upper portion of the C-130 Fuselage

Shows rear of antenna.

Antenna rotated in AZ & EL

Shows front of antenna.

Antenna rotated in EL only.

VX-30-2013-00060

(TM Antenna) roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text

ENCL (3)

Operator Pallet (Photos) roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text

2/11/2014 RACK Layout w/ Labels (ROY, REV 1, 1-21-2014) 1

C-130 TM Operator Pallet

Operator will be facing forward in acft.

Overhead Cable Support Bar

Horizontal Cable Support Bar

Egress on left side of rack.

ACFT FWD

RACK #3 RACK #2 RACK #1

C-130 TM Operator Pallet -- Racks

(FRONT VIEW)

2/11/2014 RACK Layout w/ Labels (ROY, REV 3, 2-5-2014) 2

RACK #1

C-130 TM Operator Pallet

(FRONT VIEW)

GPS/Time Code Generator [Spectracom, Secure Sync]

Antenna Control Unit (ACU) [Ktech, Antenna Operating Station]

Keyboard

Iridium Computer (CoreSystems)

Iridium Data (Multiplexed Iridium Link)

L-band Re-rad

UPS (Falcon, ED-2400RM-1)

Decomm Computer

2/11/2014 RACK Layout w/ Labels (ROY, REV 3, 2-5-2014) 3

NOTE: 4-Port GPS Splitter & Power Strip are on rear of the rack

RACK #2

(FRONT VIEW)

RF Up Converter 1 (Cross Tech, 2015)

Spectrum Analyzer (Rohde&Schwarz, FSL6)

Oscilloscope (Tektronix, DPO4104B)

Keyboard/Monitor (KVM)

Comm Box, ICS (AMS43 & Flight Cell DZM)

RF Signal Generator (Rohde&Schwarz, SMBV100A)

RF Multicoupler (Ktech, KMC-LS-02-08-SMA)

IMU/GPS

Wave Form Generator (RF Networks, SK10155)

4-Port RF Rotary Switch

RF Up Converter 2 (Cross Tech, 2015)

UPS (Falcon, ED-2400RM-1)

2/11/2014 RACK Layout w/ Labels (ROY, REV 1, 1-21-2014) 4

RACK #3

(FRONT VIEW)

Patch Panel (Trompeter, JSI-52/J3)

TM Recorder (Zodiac/Heim, GSS-102) [* -- mounted from the rear of the rack]

Keyboard/Monitor (Startech, RACKCONS 1708)

TM Receiver 2 (Semco, RC200-2)

TM Receiver 1 (Semco, RC200-2)

TM Controller (Zodiac/Heim, GSSr2)

Freq Converters 1 & 2 (Unitron, PS-94-444-29B)

2/11/2014 RACK Layout w/ Labels (ROY, REV 3, 2-5-2014) 5

RACK #3 RACK #2 RACK #1

(REAR VIEW)

2/11/2014 RACK Layout w/ Labels (ROY, REV 3, 2-5-2014) 6

Pallet/Rack Disconnect Panel

Pallet/Rack Power Disconnect Panel

4-Port GPS Splitter (view obstructed by rack) Power Strips

2/11/2014 RACK Layout w/ Labels (ROY, REV 1, 1-21-2014) 7

Pallet/Rack Disconnect Panel

Pallet/Rack Power Disconnect Panel

2/11/2014 RACK Layout w/ Labels (ROY, REV 1, 1-21-2014) 8

4-Port GPS Splitter

Overhead Cable Support Bar

Keyboard Monitor

Horizontal Cable Support Bar

ENCL (4)

Previously Installed Items (Photos)

VX-30-2012-00050A (ELECTRICAL WIRING, PWR, ICS – Part 1 of 3 slides)

Nose Wheel Well – looking FWD Nose Wheel Well – looking AFT Nose Wheel Well – Pressure Bulkhead

Wiring in Nose Wheel well area

Wiring under Flight Station area

FS-165 Pressure Blkhd – looking FWD FS-245 Disconnect Panel – looking AFT Cable run – looking FWD

FLT CLNC: 042003Z DEC 2013

Overhead Disconnect Panel wiring

Iridium/GPS Mounting Panel – looking up

View from below View from above panel

Iridium/GPS Antennas

Iridium/GPS antennas on roof

VX-30-2012-00050A (ELECTRICAL WIRING, PWR, ICS – Part 2 of 3 slides)

FLT CLNC: 042003Z DEC 2013

Location of DASC Power Circuit Breakers

New 25-A Circuit Breakers installed

ICS

ICS near FS-245, Port side (AFT of ladder)

ICS cabling

VX-30-2012-00050A (ELECTRICAL WIRING, PWR, ICS – Part 3 of 3 slides)

VX-30-2012-00050B (Doubler & FS-245 Disconnect Panel)

Doubler at Pressure Bulkhead, w/ feedthru connectors (before final paint)

FS-165

FS-245 Disconnect Panel

VX-30-2012-00050C (Overhead Disconnect Panel )

Location of Overhead Disconnect Panel Overhead Disconnect Panel

FS-335

VX-30-2012-00050D (Iridium-GPS Antenna)

Top View – w/o radome Underside View – shows mounting plate

FLT CLNC: 202009Z DEC 2012

FLT CLNC: 202009Z DEC 2012

VX-30-2012-00050E (L-band Antennas )

Location of DASC antennas

NAVAIR 01-75GAA-2-8

(2) L-band antennas replaced the (2) DASC UHF antennas

FS-562

FS-483

FLT CLNC: 202009Z DEC 2012

ENCL (5)

TM Functional & Electrical Dwgs

H

G

F

E

D

C

B

A

8 7 6 5 4 3 2 1

H

G

F

E

D

C

B

A

8 7 6 5 4 3 2 1

TM ANTENNA

PEDESTAL

TM RECEIVERS

(x2)

RF

MULTICOUPLER

UPCONVERTER

L-BAND RE RAD SPECTRUM

ANALYZER

ACU

4-PORT RF

SWITCH

IMU/GPS

RHC/LHC

IF

AGC/AM

CLK/DATA

L BAND

ANTENNA

DECOMM

COMPUTER

RECORDER

IRIG-B

GPS

IRIDIUM LINK

COMPUTER

4-PORT

SPLITTER

GPS/TIME CODE

GEN

GPS ANTENNA

IRIG-B

GPS

IRIG-B

IRIG-B

RHC/LHC

IRIDIUM DATA

ANTENNA

SYSTEM

CONTROLLER

TM Functional Block Diagram

Revision Date:

Drawn By:

JT Hernandez

Sheet Title:

TM Functional Block Diagram

C-130 TM System

SIZE: FSCM NO.: DWG NO.: REV.:

-- NAWCWD

Pt. Mugu, CA

SCALE: --

2014-0029-01

FILE

NAME:

C-130 TM FUNCTIONAL BLOCK

DIAGRAM (REV 1, ROY FROM JOSE'S

2014-0029-01).VSD

SHEET: 1 of 1 roy.sakamoto Typewritten Text TM Antenna roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text TM Antenna Pedestal roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text Escan roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text

D D

C C

B B

A A

ITAR Controlled Document:

This document contains data controlled under the international traffic in arms regulations and may not be exported, re-exported or transfered to a foreign person or destination without the authorization of the U.S. Department of State. Title

Size Part Number Rev

Date Sheet of

1300 EUBANK BLVD, SE

ALBUQUERQUE, NM 87123

TEL: (505) 998-5830

FAX: (505) 998-5836

Designed

Checked

Approved

Cannot open file Z:\Altium Library\Raytheon_Ktech_Logo.jpg

08/10/2012

M. PACE

08/08/2012

S. ROBERTS

08/06/2012

J. COOPER

8/21/2012 b 11-1202-020239 A

NAVY C-130 TM SYS - ESCAN MODULE CABLE HRNS

WHT

WHT/BLU

WHT

WHT/BLU

WHT/BLU

WHT/BLU

WHT/BLK

WHT

WHT

WHT

WHT/BLU

WHT

WHT/BLU

WHT/BLU

WHT/BLU

WHT

WHT20AWG

20AWG

20AWG

20AWG

20AWG

20AWG

20AWG

20AWG

TABLE 1

ESCAN MODULE 30.0 INCHES

HARNESS LABEL LENGTH

SEE TABLE 1

A B C

D E F

G H

J K

P2

D38999/26WC98PN

ESCAN D0

ESCAN D1

ESCAN D2

ESCAN D3

DGND

EN

SHIELD

ESCAN +24V

ESCAN 24V RET

ESCAN D0

ESCAN D1

ESCAN D2

ESCAN D3

DGND

EN

SHIELD

ESCAN +24V

ESCAN 24V RET

D B

-1

P1

M24308/4-2

WHT/BLK

108 9

15 16 17

34 20 20

1. ELECTRICALLY TEST CABLE ASSEMBLY USING BEST

COMMERCIAL PRACTICES.

2. TOLORANCES ARE AS FOLLOWS:

FOR LENGTH +/- 1.0 INCH

ALL UNUSED PIN CONTACTS WILL BE INSERTED IN

M38999/26WC98PN AND PASSED THROUGH ON CONTACT (H).

ALL SHIELD WIRES WILL BE TERMINATED IN CONNECTOR

M38999/26WC95PN USING M39029/58-363 CONTACTS.

NOTES:

ALL UNUSED PIN CONTACTS WILL BE INSERTED IN

M24308-4/2 AND PASSED THROUGH ON CONTACT (3).

ALL SHIELD WIRES WILL BE TERMINATED IN CONNECTOR

M24308/4-2 USING M39029/64-369 CONTACTS.6

PLACE EPS-300-1/2-BLK ADHESIVER LINED SHRINK TUBING

OVER ENTIRE CABLE LENGTH, 30.0".

PLACE TEXT LABEL 2.0" FROM END OF BACKSHELL. LABEL

CABLE USING CENTER JUSTIFICATION;

ESCAN MODULE

11-1202-020239

TO J2

ESCAN MODULE

11-1202-020239

TO J1

roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text Antenna to Pedestal Cable Pedestal-0 cable roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text RHCP-0, LHCP-0 cables

The cables from the DASC Overhead Disconnect Panel to the L-band Antennas are pre-existing cables that were installed as part for DASC AFC.

roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text

D D

C C

B B

A A

ITAR Controlled Document:

This document contains data controlled under the international traffic in arms regulations and may not be exported, re-exported or transfered to a foreign person or destination without the authorization of the U.S. Department of State. Title

Size Part Number Rev

Date Sheet of

1300 EUBANK BLVD, SE

ALBUQUERQUE, NM 87123

TEL: (505) 998-5830

FAX: (505) 998-5836

Designed

Checked

Approved

Cannot open file Z:\Altium Library\Raytheon_Ktech_Logo.jpg

07/27/2012

M. PACE

07/25/2012

S. ROBERTS

07/23/2012

J. COOPER

8/21/2012

B 11-1202-020222 A

NAVY C-130 - TM RACK 2 CONTROL PANEL

M

IL

-D

TL

-2

J1

D38999/20WJ61SN

M

IL

-D

TL

-2

J2

MS3470W12-10SW

1FT

PE9128

1FT

PE9128

1FT

PE9128

1FT

PE9128

1 FT

PE9154

1 FT

PE9154

1 FT

PE9154

1 FT

PE9154

1 FT

PE9154

1 FT

PE9154

1 FT

PE9154

1 FT

PE9154

1 FT

PE9154

1SHFT

PE9093

RG400/U

11-1202-020229

IRID DATA 1IRIDIUM DATA 1

RG400/U

11-1202-020229

IRID DATA 2IRIDIUM DATA 2

RG400/U

11-1202-020229

IRID DATA 3IRIDIUM DATA 3

RG400/U

11-1202-020229

IRID DATA 4IRIDIUM DATA 4

RG400/U

11-1202-020229

IRID DATA 5IRIDIUM DATA 5

RG400/U

11-1202-020229

IRID DATA 6IRIDIUM DATA 6

RG400/U

11-1202-020229

IRID VOICEIRIDIUM VOICE

PED CONTROL

11-1202-020224

PEDESTAL

PE-C400

11-1202-020228

RX RHCP

ICS TIE

11-1202-020225

ICS TIE

RG400/U

11-1202-020229

GPS IN

RG400/U

11-1202-020229

GPS OUT

RG316/U

11-1202-020232

IRIG-B OUT

PE-C400

11-1202-020228

RX LHCP

PE-C400

11-1202-020228

L-BAND RF OUT 1

PE-C400

11-1202-020228

L-BAND RF OUT 2

PEDESTAL

ICS TIE

GPS IN

GPS OUT

IRIG-B OUT

L-BAND

L-BAND

RX RF IN

RX RF IN

LHCP

RHCP

RF OUT 1

RF OUT 2

roy.sakamoto Typewritten Text

D D

C C

B B

A A

ITAR Controlled Document:

This document contains data controlled under the international traffic in arms regulations and may not be exported, re-exported or transfered to a foreign person or destination without the authorization of the U.S. Department of State. Title

Size Part Number Rev

Date Sheet of

1300 EUBANK BLVD, SE

ALBUQUERQUE, NM 87123

TEL: (505) 998-5830

FAX: (505) 998-5836

Designed

Checked

Approved

Cannot open file Z:\Altium Library\Raytheon_Ktech_Logo.jpg

07/274/2012

M. PACE

07/25/2012

S. ROBERTS

07/23/2012

J. COOPER

8/21/2012

B 11-1202-020224 A

NAVY C-130 - TM RACK 2 PEDESTAL CABLE

WHT/BLU

WHT

WHT

WHT/BLU

WHT

WHT/BLU

WHT

WHT/BLU

WHT/BLU

WHT

WHT/BLU

WHT

WHT

WHT/BLU

WHT

WHT/BLU

WHT

WHT/BLK

WHT

WHT/BLU

WHT/BLU

WHT

WHT/BLU

WHT

GRN

WHT/BLK

WHT/BLU

WHT

WHT/BLU

WHT

WHT/BLU

WHT/BLU

WHT

WHT/BLU

WHT

WHT/BLU

WHT

WHT

WHT/BLU

WHT

WHT/BLU

WHT

WHT/BLU

WHT

WHT/BLU

WHT

WHT/BLU

WHT

20AWG

20AWG

20AWG

20AWG

20AWG

20AWG

20AWG

20AWG

20AWG

20AWG

20AWG

20AWG

20AWG

20AWG

20AWG

20AWG

20AWG

20AWG

20AWG

20AWG

20AWG

20AWG

WHT/BLK

TABLE 1

PEDESTAL 36.0 INCHES

HARNESS LABEL LENGTH

SEE TABLE 1

A B C D

E

F

G H

J K

L

M

S T

U

V

W X Y Z a b c d e f g h k p q r s t u v i j y z

AA

BB

EE

CC

DD

HH

JJ

KK

LL

PP

MM

NN

x w

N

P R n m

FF

GG

D38999/26WJ61PN

WHT

WHT/BLU

WHT

WHT/BLU

GRN

WHT/BLU

EL RES R1

EL RES R2

EL RES S1

EL RES S3

SHIELD

EL RES S2

EL RES S4

EL THERMAL(+)

EL THERMAL(-)

WHT/BLK

EL ENC CLK(+)

EL ENC CLK(-)

EL ENC DATA(+)

EL ENC DATA(-)

SHIELD

EL +24V

EL 24V RET

AZ RES R1

AZ RES R2

AZ RES S1

AZ RES S3

SHIELD

AZ ENC CLK(+)

AZ ENC CLK(-)

AZ ENC DATA(+)

AZ ENC DATA(-)

SHIELD

ESCAN D0

ESCAN D1

ESCAN D2

ESCAN D3

DGND

EN

SHIELD

AZ +24V

AZ 24V RET

AZ RES S2

AZ RES S4

AZ THERMAL(+)

AZ THERMAL(-)

ESCAN +24V

ESCAN 24V RET

WHT

WHT/BLU

WHT

WHT/BLU

WHT

WHT/BLU

WHT/BLU

WHT

WHT/BLU

WHT

WHT

WHT/BLU

WHT

WHT/BLU

WHT

WHT/BLK

WHT/BLU

WHT

WHT/BLK

WHT

WHT/BLU

WHT

WHT/BLU

GRN

WHT/BLU

WHT/BLK

WHT

WHT/BLU

WHT/BLK

20AWG

20AWG

20AWG

20AWG

20AWG

20AWG

20AWG

20AWG

20AWG

20AWG

20AWG

20AWG

20AWG

20AWG

20AWG

20AWG

20AWG

20AWG

20AWG

20AWG

20AWG

20AWG

20AWG

GRN

WHT/BLK

WHT/BLK

WHT

WHT/BLK

WHT/BLU

WHT

WHT/BLU

WHT

WHT/BLU

WHT/BLU

WHT

WHT/BLU

WHT

WHT/BLU

WHT

WHT

WHT/BLU

WHT

WHT/BLU

WHT

WHT/BLU

WHT

WHT/BLU

WHT

WHT/BLU

WHT

WHT/BLK

WHT/BLK

20AWG

20AWG

20AWG

20AWG

20AWG

20AWG

WHT/BLU

WHT

WHT/BLU

WHT

WHT/BLU

WHT

WHT/BLK

WHT/BLU

WHT

20AWG

20AWG

EL PHASE (U)

EL PHASE (V)

EL PE

EL BRAKE(+)

EL BREAK(-)

SHIELD

EL PHASE (U)

EL PHASE (V)

EL PHASE (W)

EL PHASE (W)

AZ PHASE (U)

AZ PHASE (V)

AZ PE

AZ PHASE (U)

AZ PHASE (V)

AZ BRAKE(+)

AZ BREAK(-)

SHIELD

AZ PHASE (W)

AZ PHASE (W)

NOTES:

1. ELECTRICALLY TEST CABLE ASSEMBLY USING BEST

COMMERCIAL PRACTICES.

2. TOLORANCES ARE AS FOLLOWS:

FOR LENGTH +/- 1.0 INCH

ALL SHIELD WIRES WILL BE TERMINATED IN CONNECTOR

3 D38999/26WJ61PN AND PASSED THROUGH ON CONTACTS

(f), (h), (L), (r), (p), (N) AND (PP).

ALL SHIELD WIRES WILL BE TERMINATED IN CONNECTOR

D38999/20WJ61SN AND PASSED THROUGH ON CONTACTS

(f), (h), (L), (r), (p), (N) AND (PP).

3 4

PLACE TEXT LABEL 2.0" FROM END OF BACKSHELLS. LABEL

CABLE USING CENTER JUSTIFICATION;

PEDESTAL

11-1202-020224

TO J1

PEDESTAL

11-1202-020224

TO PEDESTAL

A B C D

E

F

G H

J K

L

M

S T

U

V

W X Y Z a b c d e f g h k p q r s t u v i j y z

AA

BB

EE

CC

DD

HH

JJ

KK

LL

PP

MM

NN

x w

N

P R n m

FF

GG

D38999/20WJ61SN

21 22 23 2425 25

5354 5459

D D

C C

B B

A A

ITAR Controlled Document:

This document contains data controlled under the international traffic in arms regulations and may not be exported, re-exported or transfered to a foreign person or destination without the authorization of the U.S. Department of State. Title

Size Part Number Rev

Date Sheet of

1300 EUBANK BLVD, SE

ALBUQUERQUE, NM 87123

TEL: (505) 998-5830

FAX: (505) 998-5836

Designed

Checked

Approved

Cannot open file Z:\Altium Library\Raytheon_Ktech_Logo.jpg

07/27/2012

M. PACE

07/25/2012

S. ROBERTS

07/23/2012

J. COOPER

8/21/2012

B 11-1202-020228 A

NAVY C-130 - TM RACKS LMR400 COAX CABLES

1FT

PE44522

1 FT

PE44522

SEE TABLE 1

TABLE 1

RX RHCP 65.0 INCHES

HARNESS LABEL LENGTH

RX LHCP 65.0 INCHES

L-BAND RF OUT 1 48.0 INCHES

L-BAND RF OUT 2 48.0 INCHES

60 60

1. ELECTRICALLY TEST CABLE ASSEMBLY USING BEST

COMMERCIAL PRACTICES.

2. TOLORANCES ARE AS FOLLOWS:

FOR LENGTH +/- 0.5 INCH

NOTES:

D D

C C

B B

A A

ITAR Controlled Document:

This document contains data controlled under the international traffic in arms regulations and may not be exported, re-exported or transfered to a foreign person or destination without the authorization of the U.S. Department of State. Title

Size Part Number Rev

Date Sheet of

1300 EUBANK BLVD, SE

ALBUQUERQUE, NM 87123

TEL: (505) 998-5830

FAX: (505) 998-5836

Designed

Checked

Approved

Cannot open file Z:\Altium Library\Raytheon_Ktech_Logo.jpg

07/27/2012

M. PACE

07/25/2012

S. ROBERTS

07/23/2012

J. COOPER

8/21/2012

B 11-1202-020230 A

NAVY C-130 - TM RACKS RG400/U, SMA-M TO SMA-M

SEE TABLE 1

TABLE 1

RX RHCP_1 55.0 INCHES

HARNESS LABEL LENGTH

RX LHCP_1 55.0 INCHES

L-BAND SMPL_1 55.0 INCHES

L-BAND SMPL_2 55.0 INCHES

1FT

PE4008

1 FT

PE4008

4657 57

1. ELECTRICALLY TEST CABLE ASSEMBLY USING BEST

COMMERCIAL PRACTICES.

2. TOLORANCES ARE AS FOLLOWS:

FOR LENGTH +/- 0.5 INCH

NOTES:

D D

C C

B B

A A

ITAR Controlled Document:

This document contains data controlled under the international traffic in arms regulations and may not be exported, re-exported or transfered to a foreign person or destination without the authorization of the U.S. Department of State. Title

Size Part Number Rev

Date Sheet of

1300 EUBANK BLVD, SE

ALBUQUERQUE, NM 87123

TEL: (505) 998-5830

FAX: (505) 998-5836

Designed

Checked

Approved

Cannot open file Z:\Altium Library\Raytheon_Ktech_Logo.jpg

07/27/2012

M. PACE

07/25/2012

S. ROBERTS

07/23/2012

J. COOPER

8/21/2012

B 11-1202-020231 A

NAVY C-130 - TM RACKS RG400/U, SMA-M TO BNC-M

SEE TABLE 1

TABLE 1

L-BAND OUT 1 48.0 INCHES

HARNESS LABEL LENGTH

L-BAND OUT 2 48.0 INCHES

1FT

PE4008

1 FT

PE4044

57 57

1. ELECTRICALLY TEST CABLE ASSEMBLY USING BEST

COMMERCIAL PRACTICES.

2. TOLORANCES ARE AS FOLLOWS:

FOR LENGTH +/- 0.5 INCH

NOTES:

D D

C C

B B

A A

ITAR Controlled Document:

This document contains data controlled under the international traffic in arms regulations and may not be exported, re-exported or transfered to a foreign person or destination without the authorization of the U.S. Department of State. Title

Size Part Number Rev

Date Sheet of

1300 EUBANK BLVD, SE

ALBUQUERQUE, NM 87123

TEL: (505) 998-5830

FAX: (505) 998-5836

Designed

Checked

Approved

Cannot open file Z:\Altium Library\Raytheon_Ktech_Logo.jpg

07/27/2012

M. PACE

07/25/2012

S. ROBERTS

07/23/2012

J. COOPER

8/21/2012

B 11-1202-020229 A

NAVY C-130 - TM RACKS RG400/U, TNC-M TO TNC-M

SEE TABLE 1

TABLE 1

GPS IN 15.0 INCHES

HARNESS LABEL LENGTH

GPS IN 1

GPS IN 2

GPS OUT

1FT

PE4047

1 FT

PE4047

IRID DATA 1

IRID DATA 2

IRID DATA 3

IRID DATA 4

IRID DATA 5

IRID DATA 6

IRID VOICE

43 43

4657 57

1. ELECTRICALLY TEST CABLE ASSEMBLY USING BEST

COMMERCIAL PRACTICES.

2. TOLORANCES ARE AS FOLLOWS:

FOR LENGTH +/- 0.5 INCH

NOTES:

40.0 INCHES

40.0 INCHES

12.0 INCHES

40.0 INCHES

40.0 INCHES

40.0 INCHES

40.0 INCHES

40.0 INCHES

40.0 INCHES

40.0 INCHES

D D

C C

B B

A A

ITAR Controlled Document:

This document contains data controlled under the international traffic in arms regulations and may not be exported, re-exported or transfered to a foreign person or destination without the authorization of the U.S. Department of State. Title

Size Part Number Rev

Date Sheet of

1300 EUBANK BLVD, SE

ALBUQUERQUE, NM 87123

TEL: (505) 998-5830

FAX: (505) 998-5836

Designed

Checked

Approved

Cannot open file Z:\Altium Library\Raytheon_Ktech_Logo.jpg

07/27/2012

M. PACE

07/25/2012

S. ROBERTS

07/23/2012

J. COOPER

8/21/2012

B 11-1202-020232 A

NAVY C-130 - TM RACKS RG316/U, BNC-M TO BNC-M

SEE TABLE 1

TABLE 1

IRIG-B OUT 64.0 INCHES

HARNESS LABEL LENGTH

IRIG-B OUT 1 24.0 INCHES

1 FT

PE4043

1FT

PE4043

IRIG-B OUT 2 70.0 INCHES

56 56

1. ELECTRICALLY TEST CABLE ASSEMBLY USING BEST

COMMERCIAL PRACTICES.

2. TOLORANCES ARE AS FOLLOWS:

FOR LENGTH +/- 0.5 INCH

NOTES:

roy.sakamoto Typewritten Text

D D

C C

B B

A A

ITAR Controlled Document:

This document contains data controlled under the international traffic in arms regulations and may not be exported, re-exported or transfered to a foreign person or destination without the authorization of the U.S. Department of State. Title

Size Part Number Rev

Date Sheet of

1300 EUBANK BLVD, SE

ALBUQUERQUE, NM 87123

TEL: (505) 998-5830

FAX: (505) 998-5836

Designed

Checked

Approved

Cannot open file Z:\Altium Library\Raytheon_Ktech_Logo.jpg

07/27/2012

M. PACE

07/25/2012

S. ROBERTS

07/23/2012 DesignedBy

8/21/2012

B 11-1202-020225 A

NAVY C-130 - TM RACK 2 ICS TIE CABLE

A B C

D

E F G H J

K

MS3476W12-10PW

A B C

D

E F G H J K

MS3470W12-10SW

WHT

WHT/BLU

20AWG

20AWG

20AWG

20AWGGRY

BLK

WHT

WHT/BLU

WHT

WHT/BLUT LOW OUT

T HI OUT

L LOW IN

L HI IN

UNIV ICS TIE HI

UNIV ICS TIE LOW

28VDC GND

+28VDC

20AWG

20AWG

20AWG

20AWG

TABLE 1

ICS TIE 38.0 INCHES

HARNESS LABEL LENGTH

SEE TABLE 1

WHT

WHT/BLU

20AWG

20AWG

20AWG

20AWG GRY

BLK

WHT

WHT/BLU

WHT

WHT/BLU

20AWG

20AWG

20AWG

20AWG

26 27 28 29 3030

49 50 5354 5458

1. ELECTRICALLY TEST CABLE ASSEMBLY USING BEST

COMMERCIAL PRACTICES.

2. TOLORANCES ARE AS FOLLOWS:

FOR LENGTH +/- 1.0 INCH

ALL UNUSED PIN CONTACTS WILL BE INSERTED IN

MS3476W12-10PW AND TERMINATED ON BACKSHELL.

ALL SHIELD WIRES WILL BE TERMINATED IN CONNECTOR

MS3476W12-10PW USING M39029/4-110 CONTACTS.

NOTES:

3. CABLE LENGTH FROM MS3470W18-8P TO TB1 IS 15.0".

PLACE TEXT LABEL 2.0" FROM END OF BACKSHELL. LABEL

CABLE USING CENTER JUSTIFICATION;

ICS TIE

11-1202-020225

TO ICS TIE

ICS TIE

11-1202-020225

TO ICS TIE

ALL UNUSED PIN CONTACTS WILL BE INSERTED IN

MS3470W12-10SW AND TERMINATED ON BACKSHELL.

ALL SHIELD WIRES WILL BE TERMINATED IN CONNECTOR

MS3470W12-10SW USING M39029/5-115 CONTACTS.6

D D

C C

B B

A A

ITAR Controlled Document:

This document contains data controlled under the international traffic in arms regulations and may not be exported, re-exported or transfered to a foreign person or destination without the authorization of the U.S. Department of State. Title

Size Part Number Rev

Date Sheet of

1300 EUBANK BLVD, SE

ALBUQUERQUE, NM 87123

TEL: (505) 998-5830

FAX: (505) 998-5836

Designed

Checked

Approved

Cannot open file Z:\Altium Library\Raytheon_Ktech_Logo.jpg

07/27/2012

M. PACE

07/25/2012

S. ROBERTS

07/23/2012

J. COOPER

8/21/2012

B 11-1202-020226 A

NAVY C-130 - TM RACK 1 AC POWER CABLES

L N

GND

4782.0100

L N

GND

HBL8115V

SEE TABLE 1

TABLE 1

AC PWR_1-01 40.0 INCHES

HARNESS LABEL LENGTH

AC PWR_1-02

AC PWR_1-03

AC PWR_1-04

AC PWR_1-05

AC PWR_1-06

AC PWR_1-07

AC PWR_1-08

AC PWR_1-09

AC PWR_1-10

WHT

WHT/BLU

WHT/ORG

18AWG

18AWG

18AWG

WHT

WHT/BLU

WHT/ORG39

5257 57

1. ELECTRICALLY TEST CABLE ASSEMBLY USING BEST

COMMERCIAL PRACTICES.

2. TOLORANCES ARE AS FOLLOWS:

FOR LENGTH +/- 1.0 INCH

NOTES:

40.0 INCHES

40.0 INCHES

40.0 INCHES

40.0 INCHES

40.0 INCHES

40.0 INCHES

40.0 INCHES

40.0 INCHES

40.0 INCHES

D D

C C

B B

A A

ITAR Controlled Document:

This document contains data controlled under the international traffic in arms regulations and may not be exported, re-exported or transfered to a foreign person or destination without the authorization of the U.S. Department of State. Title

Size Part Number Rev

Date Sheet of

1300 EUBANK BLVD, SE

ALBUQUERQUE, NM 87123

TEL: (505) 998-5830

FAX: (505) 998-5836

Designed

Checked

Approved

Cannot open file Z:\Altium Library\Raytheon_Ktech_Logo.jpg

07/27/2012

M. PACE

07/25/2012

S.ROBERTS

07/23/2012

J. COOPER

8/21/2012

B 11-1202-020227 A

NAVY C-130 - TM RACK 2 AC POWER CABLES

L N

GND

4782.0100

L N

GND

HBL8115V

SEE TABLE 1

TABLE 1

AC PWR_2-01

HARNESS LABEL LENGTH

AC PWR_2-02

AC PWR_2-03

AC PWR_2-04

AC PWR_2-05

AC PWR_2-06

AC PWR_2-07

AC PWR_2-08

WHT

WHT/BLU

WHT/ORG

18AWG

18AWG

18AWG

WHT

WHT/BLU

WHT/ORG39

5257 57

1. ELECTRICALLY TEST CABLE ASSEMBLY USING BEST

COMMERCIAL PRACTICES.

2. TOLORANCES ARE AS FOLLOWS:

FOR LENGTH +/- 1.0 INCH

NOTES:

40.0 INCHES

40.0 INCHES

40.0 INCHES

40.0 INCHES

40.0 INCHES

40.0 INCHES

40.0 INCHES

40.0 INCHES

D D

C C

B B

A A

ITAR Controlled Document:

This document contains data controlled under the international traffic in arms regulations and may not be exported, re-exported or transfered to a foreign person or destination without the authorization of the U.S. Department of State. Title

Size Part Number Rev

Date Sheet of

1300 EUBANK BLVD, SE

ALBUQUERQUE, NM 87123

TEL: (505) 998-5830

FAX: (505) 998-5836

Designed

Checked

Approved

Cannot open file Z:\Altium Library\Raytheon_Ktech_Logo.jpg

07/27/2012

M. PACE

07/25/2012

S. ROBERTS

07/23/2012

J. COOPER

8/21/2012

A 11-1202-020250 A

NAVY C-130 - TM RACKS PARTS LIST PG01

FN QTY PART NUMBER DESCRIPTION MANUFACTURER NOTES

PARTS LIST

2015-22 L-BAND UPCONVERTER, 70MHz TO 950-2150MHz2

OR EQUIVALENT

OR EQUIVALENT

ED2400RM-1

SECURESYNC SPECTRACOM

FALCON ELECTRIC, INC.2.4kVA 2U RACKMOUNT FREQUENCY CONVERTER W/BATTERY BACKUP

GPS TIME AND FREQUENCY REFERENCE

OR EQUIVALENTCROSS TECHNOLOGIES

OR EQUIVALENT1

DPO4104B

RAYTHEON KTECH

OR EQUIVALENT1

SM-4MIN

ROHDE&SCHWARZ

OR EQUIVALENT1

11-1201-020130

1GHz, 20MGS/s, 20M RECORD LGTH, 4+16 CHANNEL MIXED SIGNAL OSCOPE TEKTRONIX

OR EQUIVALENT1

FSL6

DC-18.0GHz SP-4T RF SWITCH RLC ELECTRONICS

COMMUNICATION BOX

9kHz-6GHz SPECTRUM ANALYZER

SK-10155-3 MULTI-TIER WAVEFORM GENERATOR1 OR EQUIVALENTTELETRONICS TECHNOLOGY CORP.

SMBV100A 9kHz-6GHz VECTOR SIGNAL GENERATOR1 OR EQUIVALENTROHDE&SCHWARZ

S14 OR EQUIVALENT1 4-P0RT ACTIVE GPS SPLITTER GPS SOURCE

OR EQUIVALENT

OR EQUIVALENT

N/A

20554-2U001.01 CORESYSTEMS

RAYTHEON KTECH

2U 3.33GHz, I5, RACK MOUNT COMPUTER

ANTENNA CONTROL UNIT (ACU)

KNC-LS-02-08-SMA OR EQUIVALENT1 L/S-BAND RF MULTICOUPLER RAYTHEON KTECH

N/A IMU/GPS BOX1 OR EQUIVALENTRAYTHEON KTECH

N/A1 OR EQUIVALENTL-BAND RE-RAD BOX RAYTHEON KTECH

RAYTHEON KTECH OR EQUIVALENTN/A1 IRIDIUM DATA BOX

INDUSTRIAL COMPUTER INC. OR EQUIVALENT4UDX79S11 4U 3.2GHz, I7, RACK MOUNT COMPUTER

AP95642 19" RACK MOUNT BLACK PDU, (10) NEMA 5-20R APC OR EQUIVALENT

RW119-S1601 19" RACK MOUNT MONITOR/KEYBOARD W/KVM SWITCH1 OR EQUIVALENTKVM SWITCH

RK-2T 19" RACK MOUNT KEYBOARD1 OR EQUIVALENTINDUSTRIAL COMPUTER INC.

OR EQUIVALENT1 COMPAEROD38999/20WJ61SN MIL-DTL-38999 SERIES III WALL MOUNT FLANGE RECEPTICLE

MS3476W12-10PW OR EQUIVALENT1 MIL-DTL-26482 SERIES II STRAIGHT PLUG COMPAERO

2 OR EQUIVALENTM85049/52-1-12W COMPAEROMIL-DTL-26482 SERIES II STRAIGHT BACKSHELL

61 OR EQUIVALENTM39029/56-351 COMPAEROMIL-DTL-38999 SERIES III SOCKET CONTACT, SIZE 20

D38999/26WJ61PN OR EQUIVALENT1 MIL-DTL-38999 SERIES III STRAIGHT PLUG COMPAERO

M85049/38-25W MIL-DTL-38999 SERIES III STRAIGHT BACKSHELL2 OR EQUIVALENTCOMPAERO

61 OR EQUIVALENTM39029/58-363 COMPAEROMIL-DTL-38999 SERIES III PIN CONTACT, SIZE 20

10 OR EQUIVALENTM39029/4-110 COMPAEROMIL-DTL-26482 SERIES II PIN CONTACT, SIZE 20

MS3470W18-8P OR EQUIVALENT1 MIL-DTL-26482 SERIES II WALL MOUNT FLANGE CONNECTOR COMPAERO

1 OR EQUIVALENTM85049/52-1-18W COMPAEROMIL-DTL-26482 SERIES II STRAIGHT BACKSHELL

10 OR EQUIVALENTM39029/4-113 COMPAEROMIL-DTL-26482 SERIES II PIN CONTACT, SIZE 12

OR EQUIVALENT1 ARVAN, INC.

OR EQUIVALENT3

MS18029-6S-6

MS25226-8N-2

MIL STANDARD TERMINAL BLOCK AND COVER, 8-32 UNC-2A

MIL STANDARD BUS BAR ARVAN, INC.

MS3470W12-10SW OR EQUIVALENT1 MIL-DTL-26482 SERIES II STRAIGHT PLUG COMPAERO

10 OR EQUIVALENTM39029/5-115 COMPAEROMIL-DTL-26482 SERIES II SOCKET CONTACT, SIZE 20 roy.sakamoto Typewritten Text

D D

C C

B B

A A

ITAR Controlled Document:

This document contains data controlled under the international traffic in arms regulations and may not be exported, re-exported or transfered to a foreign person or destination without the authorization of the U.S. Department of State. Title

Size Part Number Rev

Date Sheet of

1300 EUBANK BLVD, SE

ALBUQUERQUE, NM 87123

TEL: (505) 998-5830

FAX: (505) 998-5836

Designed

Checked

Approved

Cannot open file Z:\Altium Library\Raytheon_Ktech_Logo.jpg

07/27/2012

M. PACE

07/25/2012

S. ROBERTS

07/23/2012

J. COOPER

8/21/2012

A 11-1202-020249 A

NAVY C-130 - TM RACKS PARTS LIST PG02

FN QTY PART NUMBER DESCRIPTION MANUFACTURER NOTES

PARTS LIST

OR EQUIVALENT1

4782.0100

PASTERNACK

OR EQUIVALENT18 HUBBELL

OR EQUIVALENT18

PE9093

15A, IEC POWER ENTRY SOCKET SCHURTER

HBL8115V

BNC F/F BULKHEAD ADAPTOR

15A, HOSPITAL GRADE POWER ENTRY PLUG

PE91284 PASTERNACK OR EQUIVALENTTYPE-N F/F BULKHEAD ADAPTOR

PASTERNACK OR EQUIVALENT9 PE9154 TNC F/F BULKHEAD ADAPTORS37

PASTERNACK OR EQUIVALENT8 PE44522 TYPE-N/M STRAIGHT CRIMP/SOLDER CONNECTOR, 0.405", (PE-C400)

PE-C4004 PASTERNACK OR EQUIVALENTLOW LOSS FLEXIBLE COAX CABLE, 0.405", DOUBLE SHIELDED

PASTERNACK OR EQUIVALENT22 PE4047 TNC/M STRAIGHT CRIMP/SOLDER CONNECTOR, 0.195", (RG400/U)

RG400/U17 PASTERNACK OR EQUIVALENTFLEXIBLE COAX CABLE, 0.195", DOUBLE SHIELDED

PE400810 PASTERNACK OR EQUIVALENTSMA/M STRAIGHT CRIMP/SOLDER CONNECTOR, 0.195", (RG400/U)

BNC/M STRAIGHT CRIMP/SOLDER CONNECTOR, 0.102", (RG316/U)

RG316/U3 PASTERNACK OR EQUIVALENTFLEXIBLE COAX CABLE, 0.195", DOUBLE SHIELDED

PE40436 PASTERNACK OR EQUIVALENT

S02-03 TE CONNECTIVITY OR EQUIVALENT52 M85319/2 3, 0.170" DIA SOLDERABLE SHRINK TUBING W/DRAIN

TE CONNECTIVITY OR EQUIVALENT12-10AWG PIDG TERMINAL RING TERMINAL, 8-323578736

WMHS23053/5-106-9-S6 WIREMASTERS OR EQUIVALENT

WMHS23053/5-108-9-S1 WIREMASTERS OR EQUIVALENT

0.25" x 1.5" FLEXIBLE POLYOLEFIN SHRINK TUBING, WHT

0.50" x 1.0" FLEXIBLE POLYOLEFIN SHRINK TUBING, WHT

WMTG-183T14 MIL-DTL-27500-18TG3T14, 3-COND, TWP, ETFE, SHIELDED CBL WIREMASTERS OR EQUIVALENT18

WMTG-202T1426 MIL-DTL-27500-20TG2T14, 2-COND, TWP, ETFE, SHIELDED CBL WIREMASTERS OR EQUIVALENT

1 WMHS23053/5-111-9-S OR EQUIVALENT1.5" x 2.5" FLEXIBLE POLYOLEFIN SHRINK TUBING, WHT WIREMASTERS

BNC/M STRAIGHT CRIMP/SOLDER CONNECTOR, 0.102", (RG316/U)PE40446 PASTERNACK OR EQUIVALENT

3M OR EQUIVALENTEPS-300-1/2 BLK8 1/2" x 2.5", 3:1 ADHESIVE LINED SHRINK TUBING, BLK

1 WMHS23053/5-109-9-S OR EQUIVALENT0.75" x 38.0" FLEXIBLE POLYOLEFIN SHRINK TUBING, WHT WIREMASTERS

15 WIREMASTERS OR EQUIVALENTMIL-W-22759/18-20-0 BLKWM22759/18-20-0

13 WIREMASTERS OR EQUIVALENTMIL-W-22759/18-20-6 BLUWM22759/18-20-6

WMTG-123T14 MIL-DTL-27500-12TG3T14, 3-COND, TWP, ETFE, SHIELDED CBL WIREMASTERS OR EQUIVALENT1

W3

G

F

E

D

C

B

A

8 7 6 5 4 3 2 1

H

G

F

E

D

C

B

A

8 7 6 5 4 3 2 1

TM System Wiring Diagram – Receivers/Recorders Interface

SYSTEM CONTROLLER

Zodiac Heim GSSR2

(RACK 3)

RECORDER

Zodiac Heim GSS-102

(RACK 3)

VGA USB RJ45

RJ45

W1

W2

Notes:

1. W1 cables connect the instrumentation to the slide out Display/Mouse/Keyboard KVM switch, Avocent, part number CPS2-6A.

2. W2 is a PS2 to USB adapter cable.

Manufacturer is Adesso, part number ADP-PU21.

3. W3 cable is CAT 6 Ethernet cable that connects the GSSR2 Heim system controller to the GSS-102 interface chassis.

4. W4 cables are RG-142 terminated with male BNC connectors, Pasternack, part number

PE4044.

5. W5 cables are RG-142 terminated with male N Type connectors, Pasternack, part number PE4042 at receiver and SMA connectors, part number PE4008 at RF Multicoupler.

6. W6 cables are RG-316 terminated with male BNC connectors, Pasternack, part number

PE4043.

7. W7 cables are RG-179 coax cables terminated with male BNC connectors, Pasternack, part number PE4604.

8. W8 cables are RG-142 terminated with male BNC connectors, Pasternack, part number PE4044 at patch panel and male SMA connectors, part number PE4008 at IF Up Converters.

9. Cabling is built and installed in accordance with

NAVAIR 01-1A-505.

TM RECEIVER

SEMCO RC200-2

Receiver RX 1

(RACK 3)

VGA

Mouse Keyboard

TM RECEIVER

SEMCO RC200-2

Receiver RX 2

(RACK 3)

ACU

KAOS

(Rack 1)

AGC 1

AM 1

AGC 3

AM 3

AGC 2

AM 2

C2D1 D2C1

PCM Inputs

PCM Outputs

C2D1 D2C1 IN1IN2 O1 O2 IN O

ANALOG IN/OUT

IRIG-B TIMING IN/OUT

C1 IN1

O

TCG

REC

RX1 OUTPUTS RX2 OUTPUTS

REC OUTPUTS

C CD D

C CD DD1 C2

REC

D2

REC ANALOG

IN2 O1 O2 IN

O

TCG

O

O DECOMM

COMPUTER

(Rack 1)DATA

CLK

DATA

CLK

W6

GPS/TIME CODE GEN

(Rack 1)

IRIG B

IRIG B

IRIG B

RF MULTICOUPLER

(Rack 2)J1-1

J2-1 J1-3 J2-3

W5

KEYBOARD/MONITOR

Slide out

(RACK 3)

Prt 1Prt 2Prt 3Prt 4Prt 5

C1 D1

DECOM

IF

IN

O IF1

IF2

MON

VD1

VD2

J28 VD1

J26 VD0

J27 VD3

J25 VD2

J1 RF

J11 RF

J23 IF

J20 VD3

J7 IF1

J17 IF2

J10 VD3

J3 AGC A (LHC)

J2 AM (LHC)

J28 VD1

J26 VD0

J27 VD3

J25 VD2

J1 RF

J11 RF

J23 IF

J10 VD3

J7 IF1

J17 IF2

J20 VD3

C2 D2

DECOM

C CD D

IN IF2 VD2

IF

O IF1

MON

VD1

MONMON

UPCONVERTER 2

(Rack 2)

IF IN

UPCONVERTER 1

(Rack 2)

IF IN

W8

W4

W7

AGC 4

AM 4

J13 AGC B (RHC)

J12 AM (RHC)

J3 AGC A (LHC)

J2 AM (LHC)

J13 AGC B (RHC)

J12 AM (RHC)

VGA

Mouse Keyboard

Revision Date:

Drawn By:

JT Hernandez

Sheet Title:

TM System Diagram – RX RCDRS Interface

TM System

SIZE: FSCM NO.: DWG NO.: REV.:

-- NAWCWD

Pt. Mugu, CA

SCALE: --

2014-0030-01

FILE

NAME:

TM SYSTEM WIRING DIAGRAM - RX

RCDR INTERFACE 2014-0030-01.VSD SHEET: 1 of 2

F

E

D

C

B

A

8 7 6 5 4 3 2 1

H

G

F

E

D

C

B

A

8 7 6 5 4 3 2 1

SIZE: FSCM NO.: DWG NO.: REV.:

A NAWCWD

Pt. Mugu, CA

SCALE:

2014-0030-01

FILE

NAME:

TM SYSTEM WIRING DIAGRAM - RX RCDR

INTERFACE 2014-0030-01.VSD SHEET: 2 of 2

Cables Types

RJ-45 PICWIRE# 110339

Notes:

1. W3 cable is CAT 6 Ethernet cable that connects the GSSR2 Heim system controller to the GSS-102 interface chassis.

2. W4 cables are RG-142 terminated with male BNC connectors, Pasternack, part number PE4044.

3. W5 cables are RG-142 terminated with male N Type connectors, Pasternack, part number PE4042 at receiver and SMA connectors, part number PE4008 at RF Multicoupler.

4. W6 cables are RG-316 terminated with male BNC connectors, Pasternack, part number PE4043.

5. W7 cables are RG-179 coax cables terminated with male BNC connectors, Pasternack, part number PE4604.

6. W8 cables are RG-142 terminated with male BNC connectors, Pasternack, part number PE4044 at patch panel and male SMA connectors, part number PE4008 at IF Up Converters.

7. Cabling is built and installed in accordance with NAVAIR 01-1A-505.

PE4044 PE4008

W8

RG-142

6 FT

PE4604 PE4604

W7

RG-179

6 FT

PE4043 PE4043

W6

RG-316

6 FT

PE4042 PE4008

W5

RG-142

6 FT

PE4044 PE4044

W4

RG-142

6 FT

W3 PICWIRE CAT6 part # E50824

3 FT

RJ-45

PICWIRE#

110339

F

E

D

C

B

A

8 7 6 5 4 3 2 1

H

G

F

E

D

C

B

A

8 7 6 5 4 3 2 1

SIZE: FSCM NO.: DWG NO.: REV.:

A NAWCWD

Pt. Mugu, CA

SCALE:

2014-0030-01

FILE

NAME:

TM SYSTEM WIRING DIAGRAM - RX RCDR

INTERFACE 2014-0030-01.VSD SHEET: 2 of 2

Cables Types

RJ-45 PICWIRE# 110339

Notes:

1. W3 cable is CAT 6 Ethernet cable that connects the GSSR2 Heim system controller to the GSS-102 interface chassis.

2. W4 cables are RG-142 terminated with male BNC connectors, Pasternack, part number PE4044.

3. W5 cables are RG-142 terminated with male N Type connectors, Pasternack, part number PE4042 at receiver and SMA connectors, part number PE4008 at RF Multicoupler.

4. W6 cables are RG-316 terminated with male BNC connectors, Pasternack, part number PE4043.

5. W7 cables are RG-179 coax cables terminated with male BNC connectors, Pasternack, part number PE4604.

6. W8 cables are RG-142 terminated with male BNC connectors, Pasternack, part number PE4044 at patch panel and male SMA connectors, part number PE4008 at IF Up Converters.

7. Cabling is built and installed in accordance with NAVAIR 01-1A-505.

PE4044 PE4008

W8

RG-142

6 FT

PE4604 PE4604

W7

RG-179

6 FT

PE4043 PE4043

W6

RG-316

6 FT

PE4042 PE4008

W5

RG-142

6 FT

PE4044 PE4044

W4

RG-142

6 FT

W3 PICWIRE CAT6 part # E50824

3 FT

RJ-45

PICWIRE#

110339

F

E

D

C

B

A

8 7 6 5 4 3 2 1

H

G

F

E

D

C

B

A

8 7 6 5 4 3 2 1

15 A

D C B A

15 A

E

P1

P2

A B

E

C D

D C B A

E

UPS

FALCON

ED-2400-RM-1

UPS

FALCON

ED-2400-RM-1

LGN

LGNLGN

RACK 1

RACK 2 RACK 3

TB-1

TB-2

Ø A Ø B Ø C

Ø A Ø B Ø C

PALLET/RACK

DISC FS 280

Notes:

1. TB-1, TB-2, Terminal Block is part # MS27212-6-12

2. Terminal Block Cover is Part

# MS18029-6S-12

3. CB-1, CB-2, 15 AMP Three Phase Circuit Breaker is Klixon

9TC14-15

4. P1 is MS3106R18-11S

5. P2 is MS3106R20-15P

6. Wire is M22579/11-12

7. Wire is M27500-12TG3T14

8. Fabrication and installation complies with NAVAIR 01-1A- 505.

FREQUENCY

CONVERTER

UNITRON

PS-94-444-29B

FREQUENCY

CONVERTER

UNITRON

PS-94-444-29B

F G

A B

E

C D

F G

1 2

P1

P2 5

A B C

G H J

RACK 3RACK 2

TM System – Electrical Power for Racks

Revision Date:

Drawn By:

JT Hernandez

Sheet Title:

TM System – Electrical Power for Racks

TM System

SIZE: FSCM NO.: DWG NO.: REV.:

-- NAWCWD

Pt. Mugu, CA

SCALE: --

2014-0030-02

FILE

NAME:

TM SYSTEM - ELECTRICAL POWER

FOR RACKS (ROY, REVISED 2014-

0030-02 ON 5 FEB 2014).VSD

SHEET: 1 of 1

ENCL (6)

Electrical Loads Calculations

28V UPS #2 UPS #1

DC 60 HZ 60HZ

LOCATION EQUIPMENT A B C 120VAC, 20A 120VAC, 20A

GPS/TIME CODE GEN 80 0.7

4-PORT SPLITTER N/A

ACU 500 4.2

IRIDIUM LINK COMPUTER 520 4.3

IRIDIUM DATA 200 1.7

KEYBOARD N/A

L-BAND RE RAD 350 2.9

DECOM COMPUTER 650 5.4

UPS #1 2400

COMMUNICATION BOX 50 0.4

SPECTRUM ANALYZER 65 0.5

OSCILLOSCOPE 225 1.9

4-PORT RF SWITCH N/A

UPCONVERTER1 45 0.4

UPCONVERTER2 45 0.4

KEYBOARD/MONITOR 24 0.2

RF SIGNAL GENERATOR 150 1.3

RF NETWORK 60 0.5

RF MULTICOUPLER 30 0.3

IMU/GPS 120 1.0

UPS #2 2400

TM RECEIVER 1 120 1.0

TM RECEIVER 2 120 1.0

SYSTEM CONTROLLER 518 4.3

RECORDER 175 1.5

KEYBOARD/MONITOR 216 1.8

FREQ CONVERTER #1 12.0 12.0 12.0

FREQ CONVERTER #2 12.0 12.0 12.0

TOTALS 4363 24.0 24.0 24.0 0.0 16.4 19.2

UPS Power Capacity 20.0 20.0

Excess 3.6 0.8

RACK 1

RACK 2

RACK 3

AMPS

ELECTRICAL LOAD ANALYSIS - PROJECT POWER

PWR

WATTS

400 HZ

ENCL (7)

Weight & Balance

Rack weights CG (Rev 2 ROY 5 FEB 2013) - resized to single pages 2/12/2014, 15:21

Units are pounds and inches

Total Racks Weight 1085.68 without fasteners or clips

Left Rack (3) Middle Rack (2) Right Rack (1)

Faceplate C.G. from Faceplate C.G. from Faceplate C.G. from

Component Weight Height plate Component Weight Height plate Component Weight Height plate

Freq Cnvtr (Unitron)(2) 63 6 7 UPS (Inverter) 57.34 3.5 3.625 UPS (Inverter) 57.38 3.5 3.625 System Controller 37 3.5 14.25 IMU/GPS (Power Box) 29.48 8.75 9.75 L-Band Re Rad AMP Power Box 29.66 8.75 9.75 Receiver 1 37.12 3.5 18.25 RF Multicoupler 5.1 1.75 15 Decomm Computer 43.58 7 18.25 Receiver 2 37.12 3.5 22.25 RF Network 5.52 1.75 18 Iridium Link Computer (Core Systems) 23.28 3.5 23.5 Keyboard Monitor 33 1.75 29.125 RF Signal Generator 17.66 5.25 21.5 Iridium Data 13.88 1.75 26.625 Recorder 30 8.75 34.375 Upconverter 1 15.3 1.75 25 Keyboard 24.56 1.75 28.375 Patch Panel 6.5 3.5 49.125 Upconverter 2 14.98 1.75 27.5 ACU (K-tech Ant Operator Station) 63.28 17.5 38 Power Strip 3.5 1.75 3 Keyboard Monitor 38.48 1.75 29.25 GPS/Time Code Gen (Spectracom) 8.56 1.75 48.25

Oscilloscope 19.02 8.5 34.375 4-Port RF Splitter (Patch Panel) 2 5.25 44.75 Spectrum Analyzer 14.32 5.25 41.25 Communication Box (Flight Cell) 17.68 3.5 45.625 4-Port RF Switch (Patch Panel 1 5.25 48.25 Power Strip 3.5 1.75 3 Power Strip 3.5 1.75 3

Rack 81.5 no handles Rack 83 Rack 83 Angles .125 x 6 7.56 Angles .125 x 4 5.04 Angles .125 x 2 2.52 Angles .25 x 2 5 Angles .25 x 6 14.64 Angles .25 x 8 19.52 Mounting Plates 20 Spacers 3.1 Spacers 3 Spacers 1.5

SUB-TOTAL 362.8 SUB-TOTAL 345.16 SUB-TOTAL 377.72

Empty Pallet 540 NOTE:

Base Plate 130 Seats (2) 110 Item Weight (1 unit) Anchors (6) 3 .25" Rail - Angle 2.4 Overhead Cable Support Channel (mounted to Rack 2) 8.5 .125" Rail - Angle 1.3 Assorted Fasteners/Clips 3 Spacer 1" aprox 1.1 Cables (interconnect) 5 Spacer .375" 0.5

Fasteners < 1 per rack est.

Subtotal 799.5 NAS6603 used for faceplate mounting NAS517-3 used to attach the angles to the rack (4 per angle)

Total Pallet Loaded 1885.18 (weighed at 1862 lbs) NAS517-6 used to attach the plate to the pallet x24

Antenna Cable Support Bar (from FS 245 bulkhead) 4

C-130 TM System -- Pallet & Equipment Rack Weights

WEIGHT

Antenna 45 Pedestal 35 Mounting Plate 23.26 Support Bars 12.8 Support Bar to Mounting Plate -- angles 3.26 Mounting Plate lower part to Acft -- angles 0.75 Fasteners 1

Subtotal 121.07

C-130 TM System -- TM Antenna Weight

ENCL (8)

Structural Analysis of TM Antenna [Due to size of document it's stored in NAVPASS] roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text

ENCL (9)

Structural Analysis of TM Operator Pallet [Due to size of document it's stored in NAVPASS] roy.sakamoto Typewritten Text

ENCL (10)

MIL-704A Safe for Flight Test Results Memo roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text

ENCL (11)

Horizontal & Vertical Cable Support Bars Dwgs roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text roy.sakamoto Typewritten Text

HORIZONTAL CABLE SUPPORT BAR

VERTICAL CABLE SUPPORT BAR (Page 1 OF 3)

VERTICAL CABLE SUPPORT BAR (Page 2 OF 3)

VERTICAL CABLE SUPPORT BAR (Page 3 OF 3)

TM Antenna (Dwg & Photos)

ENCL (3):

Operator Pallet (Photos)

ENCL (4):

Previously Installed Items (Photos)

Layout & P/Ns

Receivers/Recorders Interface Dwgs Cable Types In Rack 3

ENCL (6):

Electrical Loads Calculations