Attachment 2 - PSPEC 1.1 Amend 03.pdf

Attachment 2 - PSPEC 1.1

PERFORMANCE SPECIFICATION

FOR THE

WIRED IN THE DEFENSE (WID)

MARINE ANALOG TACTICAL TELEPHONE (MATT)

PSPEC 1.1

Prepared by:

Marine Corps Systems Command

APPROVED FOR USE BY: ___________________________ DATE: _____________________

LtCol M. J. Beck

Program Manager

Command & Control Systems

DISTRIBUTION STATEMENT D: DISTRIBUTION AUTHORIZED TO DOD AND DOD CONTRACTORS

ONLY TO PRECLUDE PREMATURE DISSEMINATION, 16 July, 2020. OTHER REQUESTS FOR THIS

DOCUMENT SHOULD BE REFERRED TO COMMARCORSYSCOM (PfM CES).

DESTRUCTION NOTICE: Record copies of FOUO documents shall be disposed of in accordance with the Federal

Records Act (Title 44 Chapter 33 United States Code), and Marine Corps records management directives. Non-record FOUO documents may be destroyed by shredding or tearing into pieces and discarding the pieces in regular trash containers i

Revision Record

The table below identifies all changes incorporated into the updated version of this document after initial approval. A change in 20 percent of the document constitutes a new version.

Version Revision Description Date

1.0 - Original 16 July 2020

1.1 Updated to Version 1.0 8 January 2021

Questions concerning this document should be addressed to Product Manager, Tactical Hardware

& Infrastructure (PdM TH&I), Program Manager, Command and Control Systems (PM C2S) ii

Table of Contents

1.0 SCOPE

2.0 APPLICABLE DOCUMENTS

3.0 REQUIREMENTS

4.0 VERIFICATION

5.0 PACKAGING

6.0 NOTES

List of Tables

TABLE I. WID MATT Specification Requirements/Verifications Cross-Reference

Matrix

1.0 SCOPE

1.1 Scope. This specification prescribes the performance requirements and identifies verification methods for the Wired in the Defense (WID) Marine Analog Tactical Telephone

(MATT). The WID MATT provides the Warfighter with wired voice communications technology to be used during periods when the use of broadcast communications technologies are denied or would violate established Emissions Control (EMCON) protocols.

This is the original WID MATT performance specification. Marine tactical field telephones were traditionally used to provide a wired telecommunication network to enable and enhance command and control (C2) capabilities. The need for a small wired C2 device with no Radio

Frequency (RF) emission been identified by a Deliberate Universal Needs Statement (DUNS)

(#17073AA) to enhance and enable the command and control at the lowest levels and provide redundant C2 capability in more robust defensive communication architectures.

1.2 Requirement Levels. This specification lists two values for certain performance parameters. The threshold (T) is the minimum acceptable level. The objective (O) is the desired level at which performance of the WID MATT results in an operationally significant increase in capabilities. When only one requirement is stated, and no threshold or objective is identified, then it is the threshold requirement.

2.0 APPLICABLE DOCUMENTS

2.1 General. The documents listed in this section contain technical elements that are specified in sections 3.0 or 4.0 of this specification. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3.0 and 4.0 of this specification, whether or not they are listed here.

2.2 Government Documents.

Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified elsewhere within this document.

Unless otherwise specified, the issues of these documents are the latest versions.

DEPARTMENT OF DEFENSE STANDARDS

MIL-STD-188-124 Grounding, Bonding and Shielding for Common Long Haul/Tactical

Communication Systems Including Ground Based Communications-

Electronics Facilities and Equipment

MIL-STD-461G Requirements for the Control of Electromagnetic Interference

Characteristics of Subsystems and Equipment

MIL-STD-810H Environmental Engineering Considerations and Laboratory Tests

MIL-STD-1472G Human Engineering

MIL-STD-1474E Noise Limits

MIL-STD-882E System Safety

(Copies of these documents are available online at https://quicksearch.dla.mil/qsSearch.aspx or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)

Other Government documents, drawings and publication. The following other

Government documents, drawings, and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are the latest versions.

FEDERAL SPECIFICATIONS

SAE AMS-STD-

Colors Used in Government Procurement

MIL-HDBK-419 Grounding, Bonding and Shielding for Electronic Equipment and

Facilities

NFPA 70 National Fire Protection Association - National Electric Code (NEC)

2.3 Non-Government publication. The following documents form a part of this document to the extent specified herein. Unless otherwise indicated, the issues of these documents are the latest versions.

INSTITUTE OF ELECTRICAL AND ELECTRONICS ENGINEERS

IEEE 1100 Recommended Practice for Powering and Grounding Electronic

Equipment

2.4 Order of Precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption is obtained. In the event of a conflict between specification content and an applicable law or regulation, the contractor must contact the Contracting Officer to inquire regarding whether there is, or should be, an exemption.

3.0 REQUIREMENTS

3.1 General.

Handheld. The system shall be handheld. (T)

Weight. The total system shall weigh less than four pounds. (T) The total system shall weigh less than two pounds. (O) For the purposes of determining weight, the system is comprised of the articles listed in the Statement of Work (SOW) Paragraph 4.1.1 System Test

Articles.

Speaker. The system shall have an embedded speaker with volume control. (T) https://quicksearch.dla.mil/qsSearch.aspx

Speaker Volume. The speaker volume control shall provide a range from silent to 100 dB (± 3dB). (T)

Visual Incoming Call Indicator. The system shall provide the option for a visual indication for incoming call notification. (T)

Audio Incoming Call Indicator. The system shall provide the option for an audio indication for incoming call notification. (T)

Audio Outgoing Call Indicator. The system shall provide the option adjust speaker volume audio indication from 100 dB to silent for outgoing call initiation. (O)

Color. The system shall be either Green 383 Camouflage Chip Number 34094, Brown

383 Camouflage Chip Number 30051 or Black Camouflage Chip Number 37030. (T)

Binding Post. The system shall have a terminal binding post capable of accepting more than one field wire. (T)

Strain Relief. The binding post shall have strain relief. (T)

Keypad. The system shall not have a keypad. (T)

Silent Mode. The system shall have the ability to put the audio ring in silent mode.

(T)

Handset. The system shall provide the capability to connect to handsets available through the military supply system. (T)

Handset Free. The system shall have the capability to operate without an external handset. (T)

Special Tools. The system shall not require the use of special tools. (O)

3.2 Battery.

Batteries (USMC). The system shall have the capability to operate using batteries found in the Marine Corps supply system. (T)

Batteries (Commercial). The system shall have the capability to operate using batteries from commercially available sources. (T)

Battery Life (Standby). The system shall have a battery standby life of at least 24 hours. (T) The system shall have a battery standby life of 72 hours. (O)

Battery Life (Active). The system shall have an active in-use battery life of at least 8 hours. (T) Life (In-Use). The system shall have an active in-use battery life of 24 hours. (O)

3.3 Network Configuration.

Network Configuration. The system shall operate in a point-to-point configuration. (T)

Point-to-Point The system shall have a point-to-point distance of at least one kilometer. (T). The system shall have a point-to-point distance of three kilometers. (O)

Point-to-Multipoint. The system shall operate in a point-to-multipoint configuration.

(T)

Users. In a multi-point configuration with 100-meter separation between users, a minimum of ten users shall participate without noticeable degradation (T).

Full Duplex. The system shall be full duplex. (T)

3.4 Field Wire

WD1. The system shall have the ability to operate over WD1. (T)

WF16. The system shall have the ability to operate over WF16. (T)

CAT5. The system shall have the ability to operate over CAT5. (T)

CAT6. The system shall have the ability to operate over CAT6. (T)

3.5 Radio Frequencies.

ELF Emission. The system shall not emit RF electromagnetic radiation on the ELF frequency bands. (T)

ELF Susceptibility. The system shall not be susceptible to RF electromagnetic radiation on the ELF frequency bands. (T)

VHF Emission. The system shall not emit RF electromagnetic radiation on the VHF frequency bands. (T)

VHF Susceptibility. The system shall not be susceptible to RF electromagnetic radiation on the VHF frequency bands. (T)

HF Emission. The system shall not emit RF electromagnetic radiation on the HF frequency bands. (T)

HF Susceptibility. The system shall not be susceptible to RF electromagnetic radiation on the HF frequency bands. (T)

UHF Emission. The system shall not emit RF electromagnetic radiation on the UHF frequency bands. (T)

UHF Susceptibility. The system shall not be susceptible to RF electromagnetic radiation on the UHF frequency bands. (T)

3.6 Setup.

Setup. A point-to-point configuration shall take no more than 10 minutes to install and operate by a single user independent of the time it takes to lay the wire between the two handset locations. (T)

3.7 Environmental Requirements.

Immersion. The system shall be able to operate as required following immersion in one meter of water for 30 minutes. (T)

Transportability (Shock). The system shall withstand shock associated with transport and functional handling in accordance with MIL-STD- 516.8. (T)

Transportability (Vibrations). The system shall withstand vibrations associated with transport in trucks and trailers, aircraft, watercraft, and rail car in accordance with MIL-STD-

810H 514.8 Annex C. (T)

Operational Temperature. The system shall operate throughout a temperature range of

0 to +130 degrees F. (T)

Non-Operational Temperature. The system shall withstand temperatures throughout a temperature range from -40 to +149 degrees F (T), -40 to +158 degrees F (O).

Temperature Shock. The system shall withstand sudden changes in the temperature of the surrounding atmosphere without experiencing physical damage or deterioration in performance in accordance with MIL-STD-810H 503.7. (T)

Rain. The system shall withstand exposure to rain, water spray, and dripping water during operation without experiencing physical damage or deterioration in performance in accordance with MIL-STD-810H 506.6. (T)

Sand and Dust (Operation). In the operational mode, the system shall meet full performance requirements under conditions of blowing dust and sand in winds up to 15 miles per hour. (T)

Sand and Dust (Storage). In the storage modes, the system shall be protected from penetration by sand and dust in accordance with MIL-STD-810H 510.7. (T)

Salt Fog. The system shall withstand exposure to salt fog during operation without experiencing physical damage or deterioration in performance in accordance with MIL-STD-

810H 509.7. (T)

Humidity. The system shall operate when exposed to relative humidity up to 95% non-condensing in accordance with MIL-STD-810H 507.6. (T)

Operational Altitude. The system shall be capable of full performance between 1,300

ft. below mean sea-level and 15,000 ft. above mean sea-level. (T)

Non-Operational Altitude. The system shall not incur damage at altitudes up to

25,000 ft. above mean sea level. (T)

3.8 EMI

CS114. To control the electrical emissions and susceptibility characteristics of the system, the installation of its subsystems and associated interfaces shall conform with the following MIL-STD-461G performance requirements for Army Ground-based installation: CS

114. (T)

CS115. To control the electrical emissions and susceptibility characteristics of the system, the installation of its subsystems and associated interfaces shall conform with the following MIL-STD-461G performance requirements for Army Ground-based installation: CS

115. (T)

CS116. To control the electrical emissions and susceptibility characteristics of the system, the installation of its subsystems and associated interfaces shall conform with the following MIL-STD-461G performance requirements for Army Ground-based installation: CS

116. (T)

CS118. To control the electrical emissions and susceptibility characteristics of the system, the installation of its subsystems and associated interfaces shall conform with the following MIL-STD-461G performance requirements for Army Ground-based installation: CS

118. (T)

RS103. To control the electrical emissions and susceptibility characteristics of the system, the installation of its subsystems and associated interfaces shall conform with the following MIL-STD-461G performance requirements for Army Ground-based installation:

RS103. (T)

3.9 Workmanship.

Fabrication Quality. Finished items shall exhibit superior craftsmanship and durability, with suitability for their intended purpose. (T)

4.0 VERIFICATION

4.1 Standards. The Government shall use the verification methods described below in this section to determine if the system meets the requirements of Section 3.

TABLE I. WID MATT Specification Requirements/Verifications Cross-Reference

Matrix

METHOD OF VERIFICATION

A – Analysis

D – Demonstration

I – Inspection

T – Test

Section 3 Requirement

Section 4

Verification

Statements

Verification

Methods

A D I T

3.1 General

3.1.1 Handheld

4.2.1.1 X

3.1.2 Weight

4.2.1.2 X X

3.1.3 Speaker

4.2.1.3 X X

3.1.4 Speaker Volume

4.2.1.4 X X

3.1.5 Visual Incoming Call Indicator

4.2.1.5 X X

3.1.6 Audio Incoming Call Indicator

4.2.1.6 X

3.1.7 Audio Outgoing Call Indicator 4.2.1.7 X

3.1.8 Color

4.2.1.8 X

3.1.9 Binding Post

4.2.1.9 X X

3.1.10 Strain Relief

4.2.1.10 X X

3.1.11 Keypad

4.2.1.11 X

3.1.12 Silent Mode

4.2.1.12 X X

3.1.13 Handset 4.2.1.13 X X

3.1.14 Handset Free 4.2.1.14 X X

3.1.15 Special Tools 4.2.1.15 X

3.2 Battery

3.2.1 Batteries (USMC)

4.2.2.1 X X

METHOD OF VERIFICATION

A – Analysis

D – Demonstration

I – Inspection

T – Test

Section 3 Requirement

Section 4

Verification

Statements

Verification

Methods

A D I T

3.2.2 Batteries (Commercial) 4.2.2.2 X X

3.2.3 Battery Life (Standby) 4.2.2.3 X X

3.2.4 Battery Life (In-Use)

4.2.2.4 X X

3.3 Network Configuration

3.3.1 Network Configuration

4.2.3.1 X X

3.3.2 Point-to-Point

4.2.3.2 X X

3.3.3 Point-to-Multipoint 4.2.3.3 X X

3.3.4 Users

4.2.3.4 X X

3.3.5 Full Duplex 4.2.3.5 X X

3.4 Field Wire

3.4.1 WD1

4.2.4.1 X X

3.4.2 WF16

4.2.4.2 X X

3.4.3 CAT5

4.2.4.3 X X

3.4.4 CAT6

4.2.4.4 X X

3.5 Radio Frequencies

3.5.1 ELF Emission

4.2.5.1 X X

3.5.2 ELF Susceptibility 4.2.5.2 X X

3.5.3 VHF Emission

4.2.5.3 X X

3.5.4 VHF Susceptibility 4.2.5.4 X X

3.5.5 HF Emission

4.2.5.5 X X

3.5.6 HF Susceptibility 4.2.5.6 X X

3.5.7 UHF Emission

4.2.5.7 X X

3.5.8 UHF Susceptibility 4.2.5.8 X X

3.6 Setup

3.6.1 Setup 4.2.6.1 X X

D – Demonstration

I – Inspection

T – Test

Section 3 Requirement

Section 4

Verification

Statements

Verification

Methods

A D I T

3.7 Environmental Requirements

3.7.1 Immersion

4.2.7.1 X X

3.7.2 Transportability (Shock)

4.2.7.2 X X

3.7.3 Transportability (Vibrations)

4.2.7.3 X X

3.7.4 Operational Temperature

4.2.7.4 X X

3.7.5 Non-Operational Temperature

4.2.7.5 X X

3.7.6 Temperature Shock

4.2.7.6 X X

3.7.7 Rain

4.2.7.7 X X

3.7.8 Sand and Dust (Operation)

4.2.7.8 X X

3.7.9 Sand and Dust (Storage) 4.2.7.9 X X

3.7.10 Salt Fog

4.2.7.10 X X

3.7.11 Humidity

4.2.7.11 X X

3.7.12 Operational Altitude

4.2.7.12 X X

3.7.13 Non-Operational Altitude

4.2.7.13 X X

3.8 EMI

3.8.1 CS114

4.2.8.1 X X

3.8.2 CS115

4.2.8.2 X X

3.8.3 CS116

4.2.8.3 X X

3.8.4 CS118

4.2.8.4 X X

3.8.5 RS103 4.2.8.5 X X

D – Demonstration

I – Inspection

T – Test

Section 3 Requirement

Section 4

Verification

Statements

Verification

Methods

A D I T

3.9 Workmanship

3.9.1 Fabrication Quality

4.2.9.1 X X

4.2 Verification Statements.

General.

4.2.1.1 Handheld. During system demonstration, the handheld device must be found easy to use and transportable by a single operator when in its operational configuration.

4.2.1.2 Weight. The total system weight shall not exceed four pounds

4.2.1.3 Speaker. The system will contain speaker(s) with adjustable volume control that allows for communication at an individual or local group level.

4.2.1.4 Speaker Volume. The system will contain speaker(s) with adjustable volume control that allows for it to be heard over vehicle engine noise.

4.2.1.5 Visual Incoming Call Indicator. The visual ring indicator shall be visible at one meter away.

4.2.1.6 Audio Incoming Call Indicator. The audio incoming call indicator shall be audible from one meter away..

4.2.1.7 Audio Outgoing Call Indicator. The audio outgoing call indicator shall be audible from one meter away.

4.2.1.8 Color. By inspection, verify the system uses specified color per SAE AMS-STD- 595.

4.2.1.9 Binding Post. The binding post shall be capable of accepting multiple field wires in a multi-point configuration.

4.2.1.10 Strain Relief. Visually inspect the system for a loop, hook tie-off or other method for wire to remove direct stress to the binding posts from the wire.

4.2.1.11 Keypad. Verify by inspection that the system does not include a keyboard.

4.2.1.12 Silent Mode. Verify by analysis and demonstration that the system includes an audio ring in silent mode option.

4.2.1.13 Handset. Manufacturer’s documentation shall be analyzed to verify components utilized within the system design meet the specification. The system will be demonstrated to be compatible with commonly used military handsets.

4.2.1.14 Handset Free. Manufacturer’s documentation shall be analyzed to verify components utilized within the system design meet the specification.

4.2.1.15 Special Tools. Manufacturer’s documentation shall be analyzed to verify components utilized within the system design meet the specification.

Battery.

4.2.2.1 Batteries (USMC). Manufacturer’s documentation shall be analyzed to verify components utilized within the system design meet the specification. System shall be powered on using a variety of applicable batteries.

4.2.2.2 Batteries (Commercial). Manufacturer’s documentation shall be analyzed to verify components utilized within the system design meet the specification. System shall be powered on using a variety of applicable batteries.

4.2.2.3 Battery Life (Standby). The system is in standby, powered on and waiting to function, and will be tested to meet specification for 24 hours.

4.2.2.4 Battery Life (In-Use). The system is in-use, receiving or transmitting, and will be tested to meet specification for 8 hours.

Network Configuration.

4.2.3.1 Network Configuration. Demonstrate that the system operates without degradation.

4.2.3.2 Point-to-Point. Configure system in operational mode and demonstrate that two Marines can effectively communicate using the device.

4.2.3.3 Point-to-Multipoint. When a call ringdown is initiated from an end device, all other devices on the wire will ring and be able to receive and transmit effectively.

4.2.3.4 Users. A three-point Likert scale will be used during testing (1, 2, and 3).

Minimally acceptable is a two. All devices will be tested with the volume control at the same level.

4.2.3.5 Full Duplex. Demonstrate that two Marines can communicate effectively in full duplex mode.

Field Wire.

4.2.4.1 WD1. Manufacturer’s documentation shall be analyzed to verify components utilized within the system design meet the specification. If required, test per demo.

4.2.4.2 WF16. Manufacturer’s documentation shall be analyzed to verify components utilized within the system design meet the specification. If required, test per demo.

4.2.4.3 CAT5. Manufacturer’s documentation shall be analyzed to verify components utilized within the system design meet the specification. Test per demo.

4.2.4.4 CAT6. Manufacturer’s documentation shall be analyzed to verify components utilized within the system design meet the specification. If required, test per demo.

Radio Frequencies.

4.2.5.1 ELF Emission. RF emissions distance range shall be tested at 10 feet away from the conducting wire. ELF frequencies shall not be detected.

4.2.5.2 ELF Susceptibility. The system shall be tested in accordance with MIL-STD-461G and shall not exhibit any malfunction, degradation of performance, or deviation from operational condition as the result of electromagnetic radiation on the ELF frequency bands.

4.2.5.3 VHF Emission. RF emissions distance range shall be tested at 10 feet away from the conducting wire. VHF frequencies shall not be detected.

4.2.5.4 VHF Susceptibility. The system shall be tested in accordance with MIL-STD- 461G and shall not exhibit any malfunction, degradation of performance, or deviation from operational condition as the result of electromagnetic radiation on the VHF frequency bands.

4.2.5.5 HF Emission. RF emissions distance range shall be tested at 10 feet away from the conducting wire. HF frequencies shall not be detected.

4.2.5.6 HF Susceptibility. The system shall be tested in accordance with MIL-STD-461G and shall not exhibit any malfunction, degradation of performance, or deviation from operational condition as the result of electromagnetic radiation on the HF frequency bands.

4.2.5.7 UHF Emission. RF emissions distance range shall be tested at 10 feet away from the conducting wire. UHF frequencies shall not be detected.

4.2.5.8 UHF Susceptibility. The system shall be tested in accordance with MIL-STD- 461G and shall not exhibit any malfunction, degradation of performance, or deviation from operational condition as the result of electromagnetic radiation on the UHF frequency bands.

Setup.

4.2.6.1 Setup. Setup instructions will be analyzed for thoroughness and ease of use. One Marine will be able to setup, power on, and employ one handset in less than 10 minutes while utilizing the setup instructions.

Environmental Requirements.

4.2.7.1 Immersion. Manufacturer’s documentation shall be analyzed to verify components utilized within the system design meet the specification. Test in accordance with MIL-STD 810H Method 512.6, Immersion, Procedure I - (Immersion).

4.2.7.2 Transportability (Shock). Manufacturer’s documentation shall be analyzed to verify components utilized within the system design meet the specification. Test in accordance with MIL-STD-810H Method 516.8 Shock. Transit Drop Procedure IV, Table 516-X Tactical Transport Drop Test, Unpackaged Handling, Infantry and man-carried equipment. Drop Height of 5 ft, 5 drops (Flat bottom, two faces and two edges). If required, test in accordance with MIL-STD 810H 516.8 Functional Shock test.

4.2.7.3 Transportability (Vibration). Manufacturer’s documentation shall be analyzed to verify components utilized within the system design meet the specification. If required, test in accordance with MIL-STD 810H Method 514.8, Vibration.

4.2.7.4 Operational Temperature. Manufacturer’s documentation shall be analyzed to verify components utilized within the system design meet the specification. If required, test in accordance with MIL-STD 810H Method 501.7, High Temperature, Procedure II (Operational) and Method 502.7 Low Temperature, Procedure II (Operational).

4.2.7.5 Non-Operational Temperature. Manufacturer’s documentation shall be analyzed to verify components utilized within the system design meet the specification. If required, test in accordance with MIL-STD 810H Method 501.7, High Temperature, Procedure I (Storage) and Method 502.7 Low Temperature, Procedure I (Storage).

4.2.7.6 Temperature Shock. “Sudden changes” in temperature is defined as an air temperature change greater than 18 degrees Fahrenheit within one minute. Manufacturer’s documentation shall be analyzed to verify components utilized within the system design meet the specification. If required, test in accordance with MIL-STD 810H Method 503.7, Temperature Shock.

4.2.7.7 Rain. Manufacturer’s documentation shall be analyzed to verify components utilized within the system design meet the specification. If required, test in accordance with MIL-STD-810H, Method 506.6, Procedure I (Rain and Blowing Rain).

4.2.7.8 Sand and Dust (Operation). Manufacturer’s documentation shall be analyzed to verify components utilized within the system design meet the specification. If required, test in accordance with MIL-STD-810H, Method 510.7, Procedure I - Blowing Dust and Procedure II - Blowing Sand.

4.2.7.9 Sand and Dust (Storage). Manufacturer’s documentation shall be analyzed to verify components utilized within the system design meet the specification. If required, test in accordance with MIL-STD-810H, Method 510.7, Procedure I - Blowing Dust and Procedure II - Blowing Sand.

4.2.7.10 Salt Fog. Manufacturer’s documentation shall be analyzed to verify components utilized within the system design meet the specification. If required, test in accordance with MIL-STD-810H, Method 509.7, Salt Fog.

4.2.7.11 Humidity. Manufacturer’s documentation shall be analyzed to verify components utilized within the system design meet the specification. If required, test in accordance with MIL-STD 810H Method 507.6 Procedure II, Aggravated Cycle Table 507.6-IX, Modified from 10 cycles to 5-cycles @30-60 ℃ and 95% RH.

4.2.7.12 Operational Altitude. Manufacturer’s documentation shall be analyzed to verify components utilized within the system design meet the specification. If required, test in accordance with MIL-STD 810H Method 500.6, Low Pressure (Altitude), Procedure II (Operation).

4.2.7.13 Non-Operational Altitude. Manufacturer’s documentation shall be analyzed to verify components utilized within the system design meet the specification. If required, test in accordance with MIL-STD 810H Method 500.6, Low Pressure (Altitude), Procedure I (Storage).

EMI.

4.2.7.14 CS114. The system shall have the ability to withstand RF signals coupled onto equipment under test (EUT) associated cabling from 10 KHz to 200 MHz in accordance with MIL-STD-461G 5.12.3 CS114 Test Procedures.

4.2.7.15 CS115. The system shall have the ability to withstand impulse signals coupled onto EUT associated cabling in accordance with MIL-STD-461G 5.13.3 CS115 Test Procedures.

4.2.7.16 CS116. The system shall have the ability to withstand damped sinusoidal transients coupled onto system associated cables and power leads in accordance with MIL- STD-461G 5.14.3 CS116 Test Procedures.

4.2.7.17 CS118. The system shall withstand personnel borne electrostatic discharge (ESD) in a powered-up configuration in accordance with MIL-STD-461G 5.16.3 CS118 Test Procedures.

4.2.7.18 RS103. The system and associated cabling shall have the ability to withstand electric fields in accordance with MIL-STD-461G 5.21.3 RS103 Test Procedures.

Workmanship.

4.2.8.1 Fabrication Quality. The system will be visually inspected for processing flaws such as seams, laps, laminations, cracks, visible steps, sharp edges, nicks, scratches, burrs, deformations, and missing operation which may affect serviceability, functioning, operations, appearance or safety. Fins and other extraneous metal shall be removed from cast or forged parts.

5.0 PACKAGING

5.1 Standards. For acquisition purposes, the packaging requirements shall be as specified in the contract or order. When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory

Control Point’s packaging activity within the Military Service of Defense Agency, or within the military service’s system commands. Packaging data retrieval is available from the managing

Military Department’s or Defense Agency’s automated packaging files, Digital Versatile Disk-

Read Only Memory products, or by contacting the responsible packaging activity.

6.0 NOTES.

6.1 Verification Methods. All system performance requirements identified in the WID

MATT Specification Requirements/Verifications Cross-Reference Matrix (Table I) shall be accomplished by the Analysis, Demonstration, Inspection, or Test methods or a combination thereof. These verification methods are defined as follows:

Analysis. Verification by analysis involves proving that a system or component meets specified requirements by a technical evaluation of equations, charts, graphs, circuit diagrams and/or representative data. Applicable certifications are also submitted to confirm conformance and approval with Government and non-Government specifications, standards and/or publications. Through reviews of applicable and adequate documentation, it will be proven that the requirements have been met. Each specified piece of equipment will be identified and any specified quantities will be verified.

Demonstration. Verification that a specification requirement is met by observation of the operation or movement of the item. Non-developmental items, COTS, and Government

Furnished Materiel (GFM) are considered for demonstration only, since their implicit design has been adequately tested. Test procedures will be developed to ensure that each individual item operates as specified.

Inspection. Verification by physical manipulation, gauging, measurement, or counting involves a visual examination of the item, reviewing descriptive documentation, and comparing characteristics with a predetermined standard to determine conformance to requirements. Each specified piece of equipment will be identified and any specified quantities will be verified.

Test. Through functional and electrical means, the systematic operation of the item under required conditions, with instrumentation of the item and/or the recording/evaluation of quantitative and qualitative data will be used to prove that the requirements have been met.

The test data/test reports that are submitted shall clearly demonstrate the proposed system conforms to the requirements in section 3.

6.2 Handheld. IAW MIL-STD-1472H, paragraph 5.19 “This section addresses Personal

Electronic Devices (PED) that are carried and operated with one or two hands or worn by the user. This includes, but is not limited to, devices such as mobile telephones, tablets, and body-worn sensors.”