31S5-2FSQ217-6WC-1.pdf

TO 31S5-2FSQ217-6WC-1

WORK CARDS

SCHEDULED MAINTENANCE

FOR

MASTER CONTROL STATION (MCS),

GLOBAL POSITIONING SYSTEM

AN/FSQ-217 (V)1

LOCKHEED MARTIN INTEGRATED SYSTEMS & SOLUTIONS

F04701-96-C-0025

This revision supersedes TO 31S5-2FSQ217-6WC-1 dated 31 October 2009 and all changes.

DISTRIBUTION STATEMENT - E - Distribution authorized to DoD components only for Administrative or Operational Use (15 January 2012). Other requests shall be referred to SMC_SLG/GPL - TOMA, 1050 East Stewart Avenue, Peterson AFB, CO 80914-2902.

WARNING - This document contains technical data whose export is restricted by the Arms Export Control Act (Title 22, U.S.C., Sec. 2751 et seq) or the Export Administration Act of 1979, as amended, (Title 50, U.S.C., Appr. 2401 et seq). Violations of these export laws are subject to severe criminal penalties.

Disseminate in accordance with provisions of DoD Directive 5230.25.

HANDLING AND DESTRUCTION NOTICE - Handle in compliance with distribution statement and destroy by any method that will prevent disclosure of contents or reconstruction of the document.

Published under authority of the Secretary of the Air Force

15 JANUARY 2012

LIST OF EFFECTIVE CARDS INSERT LATEST CHANGED CARDS. DESTROY SUPERSEDED CARDS.

NOTE The portion of the text affected by the changes is indicated by a vertical line in the outer margins of the card. Changes to illustrations are indicated by shaded or screened areas, or by miniature pointing hands.

Dates of issue for original and changed cards are:

Original . . . . . . . . . . . . . . . . . . .0 . . . . . . . . . . . . . . .15 JANUARY 2012

TOTAL NO OF CARDS IN THIS PUBLICATION IS 30 CONSISTING OF THE FOLLOWING:

Card *Change Card *Change Card *Change No. No. No. No. No. No.

Title A i - viii 1-001 - 1-006 2-001 - 2-011 3-001 - 3-003 4-001

*Zero in this column indicates an original card

A USAF

PUBLICATION NUMBER

INSPECTION REQUIREMENTS

TABLE OF CONTENTS

FIGURE CHANGE NO CARD NO.

i

TABLE OF CONTENTS

Section Card

FOREWORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

SAFETY SUMMARY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

WORK AREA DIAGRAMS

DIAGRAM, WORK AREA 1 AND 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi

DIAGRAM, WORK AREA 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

DIAGRAM, WORK AREA 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii

INSPECTION

7-DAY INSPECTION, MCS WORK AREA 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-001

7-DAY INSPECTION, MCS WORK AREA 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-002

7-DAY INSPECTION, MCS WORK AREA 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-004

7-DAY INSPECTION, MCS WORK AREA 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-006

INSPECTION REQUIREMENTS

TABLE OF CONTENTS

FIGURE CHANGE NO CARD NO.

i

Section Card

SERVICING

28-DAY SERVICING, MCS WORK AREA 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-001

28-DAY SERVICING, MCS WORK AREA 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-003

28-DAY SERVICING, MCS WORK AREA 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-006

28-DAY SERVICING, MCS WORK AREA 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-010

28-DAY SERVICING, KI-17 BENCH STOCK BATTERY RECHARGING . . . . . . . . . . . . . . . . . . . . . . . . . 2-011

84-DAY SERVICING, TAPE DRIVES (1A14, 3A7A2, 3A7A3, 3A16, 3A19) . . . . . . . . . . . . . . . . . . . . . . . . 3-001

84-DAY SERVICING, TAPE DRIVE (3A7A4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-002

84-DAY SERVICING, TAPE DRIVE (3A7A5A1, 3A7A5A2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-003

546-DAY SERVICING, KI-17 BATTERY REPLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-001

INSPECTION REQUIREMENTS

FOREWORD

FIGURE CHANGE NO CARD NO.

ii

FOREWORD

These work cards are a step-by-step guide in abbreviated form for use as a reference to ensure accomplishment of selected tasks by a predetermined sequence procedure. The intent of these work cards is to eliminate the probability of omission of a step in the accomplishment of the intended task. The procedures contained herein are presented in the shortest practical form for use by qualified personnel and are not intended to provide full technical instructions. These work cards provide, in an abbreviated form, procedures for appropriate tasks, inspections, etc. These procedures are derived from, but do not replace, the detailed procedures contained in Technical Orders (TOs). When malfunctions occur, reference to the TO shall be made.

NOTE

Recommended changes to this set of work cards shall be submitted on AFTO Form 22, through command headquarters in accordance with (IAW) TO 00-5-1.

INSPECTION REQUIREMENTS

FOREWORD

FIGURE CHANGE NO CARD NO.

ii

INSPECTION REQUIREMENTS

INTRODUCTION

FIGURE CHANGE NO CARD NO.

iii

INTRODUCTION

1. THESE WORK CARDS PROVIDE THE REQUIREMENTS FOR SCHEDULED MAINTENANCE AND WILL BE USED AS A GUIDE TO ENSURE THAT NO ITEM IS OVERLOOKED. THE CARD SIZE AFFORDS CONVENIENT HANDLING BY MAINTENANCE PERSONNEL WHILE PERFORMING SCHEDULED MAINTENANCE. TO AFFORD MORE EFFICIENT MAINTENANCE PLANNING AND ASSIGNMENT OF WORK, THE REQUIREMENTS ARE ARRANGED BY WORK AREAS UTILIZING SEPARATE CARDS FOR REQUIREMENTS TO BE

ACCOMPLISHED DURING A SPECIFIC SCHEDULED MAINTENANCE FREQUENCY.

2. THE STEPS WITHIN THE WORK CARDS ARE ARRANGED TO PROVIDE A LOGICAL SEQUENCE OF THE PERFORMANCE OF THE REQUIREMENTS PERTAINING TO THE WORK AREAS TO WHICH THE CARD APPLIES. WHERE THE SAME WORK IS BEING ACCOMPLISHED, THE APPLICABLE WORK UNIT CODES ARE LISTED ONCE, OPPOSITE THE FIRST STEP OF THE PROCEDURE.

ONLY IF THE WORK UNIT CODE CHANGES FOR A STEP WILL A NEW WORK UNIT CODE BE LISTED. DETAILED INSTRUCTIONS FOR THE USE OF THESE CARDS AND THE DESCRIPTION AND APPLICATION OF OTHER FORMS AND CHARTS TO BE USED IN

CONJUNCTION WITH THESE CARDS ARE CONTAINED IN 00-20 SERIES TECHNICAL ORDERS.

3. CHANGES AND REVISIONS TO THESE WORK CARDS WILL BE PUBLISHED WHEN NECESSARY TO ADD, DELETE, REVISE, OR CHANGE REQUIREMENTS. SUCH CHANGES AND REVISIONS WILL BE BASED ON FACTUAL DATA AS A RESULT OF EXPERIENCE WITH THE EQUIPMENT. DATA WILL BE GATHERED THROUGH AFI 21-116 DATA FIELD EVALUATION, UNSATISFACTORY REPORTS, AND OTHER FACTUAL FAILURE DATA.

4. FOR ALL OUT OF SERVICE WORK CARDS, COORDINATE SERVICING TASK WITH JOB CONTROL. FAILURE TO DO SO CAN RESULT

IN LOSS OF MISSION EFFECTIVENESS.

INSPECTION REQUIREMENTS

INTRODUCTION

iii

INSPECTION REQUIREMENTS

SAFETY SUMMARY

FIGURE CHANGE NO CARD NO.

iv

1. GENERAL SAFETY INSTRUCTIONS.

The following general safety precautions are not related to any specific procedure and therefore do not appear elsewhere in this publication. These are recommended precautions that personnel must understand and apply during any phase of operation and maintenance.

1.1. Keep Away From Live Circuits. Operating personnel must at all times observe all safety regulations. Do not replace components with the AC power turned on. Under certain conditions, dangerous potentials due to charges retained by capacitors may still exist when the power control is set to the off position. To avoid severe shock or injuries, always remove power and discharge a circuit to ground before touching it.

1.2. Emergency Power Off (EPO). This facility has been equipped with Emergency Power Off (EPO) switches to remove power in the event an emergency occurs. The EPO switches are located near the exits of the equipment rooms.

1.3. Do Not Service Or Adjust Alone. Under no circumstances should any person reach into or enter the enclosure for the purpose of servicing or adjusting the equipment, except in the presence of someone who is capable of rendering aid.

1.4. RESUSCITATION. Personnel working with or near high voltages should be familiar with modern methods of resuscitation. Cardiopulmonary resuscitation procedures are provided in TO 31-1-141-1 and annual refresher training requirements are outlined in Air Force Occupational Safety and Health (AFOSH) standard (STD 91-50). Other information may be obtained from Base Medical Services.

INSPECTION REQUIREMENTS

SAFETY SUMMARY

FIGURE CHANGE NO CARD NO.

iv

1.5. Electrostatic Discharge (ESD) Sensitive Devices. If a circuit card contains a part identified as an ESD item, applicable precautions will appear in this publication. All electrostatically sensitive devices will be marked with the symbol . When an entire paragraph, including all subparagraphs, is considered ESD critical, the symbol will be placed between the step number and title.

When all subordinate paragraph steps are not related to handling maintenance, which could damage ESD parts, only those related will be annotated. The following caution will immediately precede ESD procedures/steps:

CAUTION

Observe precautions for handling electrostatic (ESD) discharge sensitive items. (Refer to TO-00-25-234)

INSPECTION REQUIREMENTS

SAFETY SUMMARY

FIGURE CHANGE NO CARD NO.

v

2. WARNINGS, CAUTIONS AND NOTES.

2.1. Definitions Of Warnings, Cautions, And Notes are Described Below.

WARNING

An operating or maintenance procedure, practice, condition, statement, etc., which, if not strictly ob-served, could result in injury to or death of personnel.

CAUTION

An operating or maintenance procedure, practice, condition, statement, etc., which, if not strictly observed, cold result in damage to, or destruction of equipment or loss of mission effectiveness

NOTE

An essential operating or maintenance procedure, condition, or statement which must be highlighted.

INSPECTION REQUIREMENTS

SAFETY SUMMARY

FIGURE CHANGE NO CARD NO.

v

3. ELECTRICAL POWER.

3.1. ON. When power is required during the accomplishment of the tasks entered on the card, the word “ON” will be placed in this block.

3.2. OFF. When it is mandatory that power be off during the accomplishment of the tasks entered on the card, the word “OFF” will be placed in this block.

3.3. ON or OFF. When power may be on or off during the accomplishment of the tasks entered on the card, this block will be left blank.

3.4. ON and OFF. When some items require power on but some require it to be off, the words “ON/OFF” will be placed in this block and each power on requirement will be preceded by an “at” (@) symbol in the body of the card.

INSPECTION REQUIREMENTS

DIAGRAM

FIGURE CHANGE NO CARD NO.

vi

WORK AREA 1 AND 2

INSPECTION REQUIREMENTS

DIAGRAM

FIGURE CHANGE NO CARD NO.

vi

WORK AREA 1 - MOD 11 ROOM 6 COMPUTER ROOM

- EQUIPMENT RACK (3A56)

WORK AREA 2 - MOD 11 ROOM 7, OPERATIONS AREA

- COSE WORKSTATIONS (1A1 - 1A12)

- NETWORK MANAGER (1A13)

- - EXTERNAL CD/RW (1A13A6)

- - TAPE DRIVE (1A14)

- PRINTERS (1A15 - 1A20)

- ALMANAC PC (1A68)

- MOW/TAT2 SYSTEM EQUIPMENT

- - MOW WORKSTATION (1A70)

- - TAT2 WORKSTATION (1A71)

- - PRINTER A/B SWITCH (1A72)

- - PRINTER (1A73)

- - KVM SWITCH, (1A74)

- - 22” MONITOR (1A75)

- - TAPE DRIVE (1A76)

INSPECTION REQUIREMENTS

DIAGRAM

FIGURE CHANGE NO CARD NO.

vii

WORK AREA 3

INSPECTION REQUIREMENTS

DIAGRAM

FIGURE CHANGE NO CARD NO.

vii

WORK AREA 3 - MOD 17A ROOM 1 COMPUTER ROOM

- OPERATIONS RACKS (3A3 - 3A9, 3A11, 3A65)

- OPS TRANSFER RACKS (3A10, 3A12, 3A13)

- SYSTEM ADMINISTRATION WORKSTATION (3A18)

- - EXTERNAL CD-RW (3A18A6)

- - TAPE DRIVE (3A19)

- LAB CONTROLLER WORKSTATION (3A20)

- - TAPE LIBRARY (3A16)

- - LAB CONTROLLER D2 RAID (3A21)

- PRINTER (3A24)

- CRYPTO 1, 2 TERMINALS (3A25, 3A26)

- SYSTEM MAINT TERMINALS (3A27, 3A28)

- EXTERNAL COMMUNICATIONS RACK (3A29)

- ARTS RACKS (3A37 - 3A42, 3A59)

- ARTS WORKSTATIONS (3A52, 3A53)

- OPS TRANSFER WORKSTATIONS (3A54, 3A55)

- ADSU RACK (3A68)

INSPECTION REQUIREMENTS

DIAGRAM

FIGURE CHANGE NO CARD NO.

viii

WORK AREA 4

INSPECTION REQUIREMENTS

DIAGRAM

FIGURE CHANGE NO CARD NO.

viii

WORK AREA 4 - MOD 11B ROOM 1 AND 2

- NAVIGATION WARFARE OPERATOR (NWO) TERMINAL (1A33, 1A34)

- PRINTER (1A22)

- MEDIA CONVERTER (1A23)

CARD NO.

1-001

WORK AREA(S)

TYPE MECH RQR MECH NO. CARD TIME

00:30

PUBLICATION NUMBER

TO 31S5-2FSQ217-6WC-1

CHANGE NO.

MAN

MIN

WORK

AREA

WORK UNIT CODE

SYS SUB 7-DAY INSPECTION

INSPECTION

REQUIREMENTS

ELECTRICAL POWER

ON

SERVICE

IN

FIGURE CARD NO.

1-001

MCS WORK AREA 1

005 1 1. INSPECT WORK AREA 1 FOR OVERALL CONDITION. CHECK AREA FOR GENERAL CLEANLINESS.

005 1 2. INSPECT EQUIPMENT RACK (3A56) FOR EXTERNAL OVERALL CLEANLINESS, DAMAGE,

CORROSION, LOOSE OR MISSING HARDWARE, AIR FLOW, AND EVIDENCE OF OVERHEATING.

020 1 3. INSPECT EQUIPMENT RACK (3A56) FOR, FOR OVERALL CONDITION.

A. OPEN RACK FRONT AND REAR DOOR.

B. CHECK RACK FOR CLEANLINESS, DAMAGE, CORROSION, LOOSE OR MISSING

HARDWARE, AIR FLOW AND EVIDENCE OF OVERHEATING.

C. CHECK RACK CABLING AND WIRING FOR DAMAGE, CHAFING, AND WEAR.

WARNING

AVOID CONTACT WITH MOVING BLOWER FAN.

D. REMOVE TWO SCREWS SECURING THE GRILL TO THE FRONT OF THE BLOWER IN THE RACK.

E. CHECK BLOWER FILTERS FOR CLEANLINESS.

F. CHECK RACK BLOWER FANS FOR PROPER OPERATION.

(CONTINUED ON BACK)

CARD NO.

1-001

WORK AREA(S)

TYPE MECH RQR MECH NO. CARD TIME

00:30

PUBLICATION NUMBER

CHANGE NO.

MAN

MIN

WORK

AREA

WORK UNIT CODE

SYS SUB 7-DAY INSPECTION

INSPECTION

REQUIREMENTS

ELECTRICAL POWER

ON

SERVICE

IN

FIGURE CARD NO.

1-001

(CONTINUED FROM FRONT)

G. CHECK FOR FAULT INDICATORS THEN REFER TO INDIVIDUAL EQUIPMENT TECHNICAL

ORDER FOR APPROPRIATE MAINTENANCE ACTION TO BE TAKEN.

H. CLOSE RACK FRONT AND REAR DOOR.

4. NOTIFY JOB CONTROL AND CREW COMMANDER OF ANY DISCREPAN-

CIES NOTED DURING INSPECTION.

1-002

WORK AREA(S)

TYPE MECH RQR MECH NO. CARD TIME

01:18

PUBLICATION NUMBER

TO 31S5-2FSQ217-6WC-1

CHANGE NO.

MAN

MIN

WORK

AREA

WORK UNIT CODE

SYS SUB 7-DAY INSPECTION

INSPECTION

REQUIREMENTS

ELECTRICAL POWER

ON

SERVICE

IN

FIGURE CARD NO.

1-002

MCS WORK AREA 2

005 2 1. INSPECT WORK AREA 2 FOR OVERALL CONDITION. CHECK AREA FOR GENERAL CLEANLINESS.

020 2 CA B00 2. COSE WORKSTATION (1A1 - 1A12).

CA BA0 A. INSPECT COMPUTER SUBASSEMBLY, DIGITAL (A1), FOR EXTERNAL CLEANLINESS,

DAMAGE, AIR FLOW AND EVIDENCE OF OVERHEATING.

CA BB0 B. INSPECT KEYBOARD AND MOUSE (A2), FOR EXTERNAL CLEANLINESS, AND DAMAGE.

CA BD0 C. INSPECT DISPLAY UNITS (A3, A4, A5), FOR EXTERNAL CLEANLINESS, DAM-

AGE, AND EVIDENCE OF OVERHEATING.

005 2 CA K00 3. ALMANAC PC WORKSTATION (1A68) .

CA KA0 A. INSPECT COMPUTER SUBASSEMBLY, DIGITAL (A1), FOR EXTERNAL CLEANLINESS,

DAMAGE, AIR FLOW AND EVIDENCE OF OVERHEATING.

CA

CA

KB0

KD0

B. INSPECT KEYBOARD AND MOUSE (A3, A4), FOR EXTERNAL CLEANLINESS, AND DAMAGE.

CA KC0 C. INSPECT DISPLAY UNIT (A2), FOR EXTERNAL CLEANLINESS, DAMAGE, AND

EVIDENCE OF OVERHEATING.

008 2 CA C00 4. NETWORK MANAGER WORKSTATION (1A13).

CA CA0 A. INSPECT COMPUTER SYSTEM, DIGITAL (A1), FOR EXTERNAL CLEANLINESS,

DAMAGE, AIR FLOW AND EVIDENCE OF OVERHEATING.

CA CB0 B. INSPECT KEYBOARD AND MOUSE (A2), FOR EXTERNAL CLEANLINESS, AND DAMAGE.

(CONTINUED ON BACK)

CARD NO.

1-002

WORK AREA(S)

TYPE MECH RQR MECH NO. CARD TIME

01:18

PUBLICATION NUMBER

WORK

AREA

WORK UNIT CODE

SYS SUB 7-DAY INSPECTION

INSPECTION

REQUIREMENTS

ELECTRICAL POWER

ON

SERVICE

IN

FIGURE CARD NO.

1-002

(CONTINUED FROM FRONT)

CA CD0 C. INSPECT DISPLAY UNIT (A3), FOR EXTERNAL CLEANLINESS, DAMAGE, AND

EVIDENCE OF OVERHEATING.

CA CE0 D. INSPECT EXTERNAL CD-RW (A6) FOR EXTERNAL CLEANLINESS, DAMAGE,

AND EVIDENCE OF OVERHEATING.

CQ A00 E. INSPECT TAPE DRIVE (1A14), FOR EXTERNAL CLEANLINESS, DAMAGE, AIR

FLOW AND EVIDENCE OF OVERHEATING.

020 2 5. MOW/TAT2 SYSTEM EQUIPMENT.

CA PA0 A. INSPECT MOW WORKSTATION (1A70), FOR EXTERNAL CLEANLINESS, DAMAGE,

AIR FLOW AND EVIDENCE OF OVERHEATING.

CA PB0 B. INSPECT KEYBOARD AND MOUSE, FOR EXTERNAL CLEANLINESS, AND DAMAGE.

CA PC0 C. INSPECT DISPLAY UNIT (1A75), FOR EXTERNAL CLEANLINESS, DAMAGE,

AND EVIDENCE OF OVERHEATING.

CA PA0 D. INSPECT TAT2 WORKSTATION (1A71), FOR EXTERNAL CLEANLINESS, DAMAGE,

AIR FLOW AND EVIDENCE OF OVERHEATING.

DE JA0 E. INSPECT KVM SWITCH (1A74) FOR EXTERNAL CLEANLINESS AND DAMAGE.

DE JB0 F. INSPECT PRINTER A/B SWITCH (1A72) FOR EXTERNAL CLEANLINESS AND DAMAGE.

CQ L00 G. INSPECT TAPE DRIVE (1A76), FOR EXTERNAL CLEANLINESS, DAMAGE, AIR

FLOW AND EVIDENCE OF OVERHEATING.

CL F00 H. INSPECT PRINTER (1A73) FOR EXTERNAL CLEANLINESS, DAMAGE, AIR FLOW

AND EVIDENCE OF OVERHEATING.

020 2 CL A00 6. INSPECT PRINTERS (1A15 - 1A19) FOR EXTERNAL CLEANLINESS, DAMAGE,

AIR FLOW AND EVIDENCE OF OVERHEATING.

(CONTINUED ON NEXT CARD)

1-003

WORK AREA(S)

TYPE MECH RQR MECH NO. CARD TIME

01:18

PUBLICATION NUMBER

TO 31S5-2FSQ217-6WC-1

CHANGE NO.

MAN

MIN

WORK

AREA

WORK UNIT CODE

SYS SUB 7-DAY INSPECTION

INSPECTION

REQUIREMENTS

ELECTRICAL POWER

ON

SERVICE

IN

FIGURE CARD NO.

1-003

(CONTINUED FROM PREVIOUS CARD

005 2 CL C00 7. INSPECT PRINTER (1A20) FOR EXTERNAL CLEANLINESS, DAMAGE, AIR FLOW

AND EVIDENCE OF OVERHEATING.

8. NOTIFY JOB CONTROL AND CREW COMMANDER OF ANY DISCREPAN-

CIES NOTED DURING INSPECTION.

(REVERSE BLANK)

CARD NO.

1-003

WORK AREA(S)

TYPE MECH RQR MECH NO. CARD TIME

01:18

PUBLICATION NUMBER

INSPECTION REQUIREMENTS

7-DAY INSPECTION

1-003

1-004

WORK AREA(S)

TYPE MECH RQR MECH NO. CARD TIME

03:18

PUBLICATION NUMBER

TO 31S5-2FSQ217-6WC-1

CHANGE NO.

MAN

MIN

WORK

AREA

WORK UNIT CODE

SYS SUB 7-DAY INSPECTION

INSPECTION

REQUIREMENTS

ELECTRICAL POWER

ON

SERVICE

IN

FIGURE CARD NO.

1-004

MCS WORK AREA 3

005 3 1. INSPECT WORK AREA 3 FOR OVERALL CONDITION. CHECK AREA FOR GENERAL CLEANLINESS.

013 3 CA C00 2. SYSTEM ADMINISTRATION WORKSTATION (3A18).

CA CA0 A. INSPECT COMPUTER SYSTEM, DIGITAL (A1), FOR EXTERNAL CLEANLINESS,

DAMAGE, AIR FLOW AND EVIDENCE OF OVERHEATING.

CA CB0 B. INSPECT KEYBOARD AND MOUSE (A2), FOR EXTERNAL CLEANLINESS, AND DAMAGE.

CA CD0 C. INSPECT DISPLAY UNIT (A3), FOR EXTERNAL CLEANLINESS, DAMAGE, AND

EVIDENCE OF OVERHEATING.

CA CE0 D. INSPECT EXTERNAL CD-RW (A6) FOR EXTERNAL CLEANLINESS, DAMAGE,

AND EVIDENCE OF OVERHEATING.

CQ A00 E. INSPECT TAPE DRIVE (3A19), FOR EXTERNAL CLEANLINESS, DAMAGE, AIR

FLOW AND EVIDENCE OF OVERHEATING.

114 3 3. INSPECT OPERATIONS EQUIPMENT RACKS (3A3 - 3A13, 3A29, 3A65) AND ARTS EQUIPMENT

RACKS (3A37 - 3A42, 3A59), FOR EXTERNAL CLEANLINESS, DAMAGE, AND AIR FLOW.

A. OPEN AND UNLOCK AS APPROPRIATE RACK FRONT AND REAR DOORS.

B. CHECK RACK FOR CLEANLINESS, DAMAGE, CORROSION, LOOSE OR MISSING

HARDWARE, AIR FLOW AND EVIDENCE OF OVERHEATING.

C. CHECK RACK CABLING AND WIRING FOR DAMAGE, CHAFING, AND WEAR.

(CONTINUED ON BACK)

CARD NO.

1-004

WORK AREA(S)

TYPE MECH RQR MECH NO. CARD TIME

03:18

PUBLICATION NUMBER

WORK

AREA

WORK UNIT CODE

SYS SUB 7-DAY INSPECTION

INSPECTION

REQUIREMENTS

ELECTRICAL POWER

ON

SERVICE

IN

FIGURE CARD NO.

1-004

(CONTINUED FROM FRONT)

WARNING

AVOID CONTACT WITH MOVING BLOWER FAN.

D. REMOVE TWO SCREWS SECURING THE GRILL TO THE FRONT OF THE BLOWER IN THE RACK.

E. CHECK BLOWER FILTERS FOR CLEANLINESS.

F. CHECK RACK BLOWER FANS FOR PROPER OPERATION.

G. REPLACE TWO SCREWS SECURING THE GRILL TO THE FRONT OF THE BLOWER.

H. CHECK FOR FAULT INDICATORS THEN REFER TO INDIVIDUAL EQUIPMENT TECHNICAL

ORDER FOR APPROPRIATE MAINTENANCE ACTION TO BE TAKEN.

I. CLOSE AND LOCK, AS APPROPRIATE, RACK FRONT AND REAR DOORS.

006 3 4. INSPECT ADSU RACK (3A68) FOR EXTERNAL CLEANLINESS, DAMAGE, AND AIR FLOW.

A. OPEN RACK FRONT AND REAR DOORS.

B. CHECK RACKS FOR CLEANLINESS, DAMAGE, CORROSION, LOOSE OR MISSING

HARDWARE, AIR FLOW AND EVIDENCE OF OVERHEATING.

C. CHECK RACK CABLING AND WIRING FOR DAMAGE, CHAFING, AND WEAR.

D. CHECK FOR FAULT INDICATORS THEN REFER TO INDIVIDUAL EQUIPMENT TECHNICAL

ORDER FOR APPROPRIATE MAINTENANCE ACTION TO BE TAKEN.

E. CLOSE RACK FRONT AND REAR DOORS.

010 3 CA D00 5. ARTS WORKSTATIONS (3A52, 3A53).

CA DA0 A. INSPECT COMPUTER SYSTEM, DIGITAL (A1), FOR EXTERNAL CLEANLINESS,

DAMAGE, AIR FLOW AND EVIDENCE OF OVERHEATING.

1-005

WORK AREA(S)

TYPE MECH RQR MECH NO. CARD TIME

03:18

PUBLICATION NUMBER

TO 31S5-2FSQ217-6WC-1

CHANGE NO.

MAN

MIN

WORK

AREA

WORK UNIT CODE

SYS SUB 7-DAY INSPECTION

INSPECTION

REQUIREMENTS

ELECTRICAL POWER

ON

SERVICE

IN

FIGURE CARD NO.

1-005

(CONTINUED FROM PREVIOUS CARD

CA DB0 B. INSPECT KEYBOARD AND MOUSE (A2), FOR EXTERNAL CLEANLINESS, AND DAMAGE.

CA DE0 C. INSPECT DISPLAY UNIT (A3), FOR EXTERNAL CLEANLINESS, DAMAGE, AND

EVIDENCE OF OVERHEATING.

CA DD0 D. INSPECT PASSIVE F/O TRANSCEIVER (A5) FOR EXTERNAL CLEANLINESS,

DAMAGE, AND EVIDENCE OF OVERHEATING.

010 3 CA E00 6. OPS TRANSFER WORKSTATIONS (3A54, 3A55).

CA EA0 A. INSPECT COMPUTER SYSTEM, DIGITAL (A1), FOR EXTERNAL CLEANLINESS,

DAMAGE, AIR FLOW AND EVIDENCE OF OVERHEATING.

CA EB0 B. INSPECT KEYBOARD AND MOUSE (A2), FOR EXTERNAL CLEANLINESS, AND DAMAGE.

CA ED0 C. INSPECT DISPLAY UNIT (A3), FOR EXTERNAL CLEANLINESS, DAMAGE, AND

EVIDENCE OF OVERHEATING.

020 3 CL D00 7. TERMINALS.

A. INSPECT CRYPTO 1 & 2 TERMINALS (3A25, 3A26) FOR EXTERNAL CLEANLINESS,

DAMAGE, AIR FLOW AND EVIDENCE OF OVERHEATING.

B. INSPECT SYSTEM MAINTENANCE TERMINALS (3A27, 3A28) FOR EXTERNAL CLEANLINESS,

DAMAGE, AIR FLOW AND EVIDENCE OF OVERHEATING.

C. INSPECT ADAPTERS (3A27A1, 3A28A1), FOR EXTERNAL CLEANLINESS AND DAMAGE.

(CONTINUED ON BACK)

CARD NO.

1-005

WORK AREA(S)

TYPE MECH RQR MECH NO. CARD TIME

03:18

PUBLICATION NUMBER

WORK

AREA

WORK UNIT CODE

SYS SUB 7-DAY INSPECTION

INSPECTION

REQUIREMENTS

ELECTRICAL POWER

ON

SERVICE

IN

FIGURE CARD NO.

1-005

(CONTINUED FROM FRONT)

005 3 CL A00 8. INSPECT PRINTER (3A24), FOR EXTERNAL CLEANLINESS, DAMAGE, AIR FLOW

AND EVIDENCE OF OVERHEATING.

015 3 CA C00 9. LAB CONTROLLER WORKSTATION (3A20).

CA CA0 A. INSPECT COMPUTER SYSTEM, DIGITAL (A1), FOR EXTERNAL CLEANLINESS,

DAMAGE, AIR FLOW AND EVIDENCE OF OVERHEATING.

CA CB0 B. INSPECT KEYBOARD AND MOUSE (A2), FOR EXTERNAL CLEANLINESS, AND DAMAGE.

CA CD0 C. INSPECT DISPLAY UNIT (A3), FOR EXTERNAL CLEANLINESS, DAMAGE, AND

EVIDENCE OF OVERHEATING.

CQ B00 D. INSPECT LAB CONTROLLER D2 RAID (3A21) FOR EXTERNAL CLEANLINESS, DAMAGE, AIR FLOW AND EVIDENCE OF OVERHEATING.

CQ F00 E. INSPECT TAPE LIBRARY (3A16) FOR EXTERNAL CLEANLINESS, DAMAGE,

AIR FLOW AND EVIDENCE OF OVERHEATING.

10.NOTIFY JOB CONTROL AND CREW COMMANDER OF ANY DISCREPAN-

CIES NOTED DURING INSPECTION.

1-006

WORK AREA(S)

TYPE MECH RQR MECH NO. CARD TIME

00:20

PUBLICATION NUMBER

TO 31S5-2FSQ217-6WC-1

CHANGE NO.

MAN

MIN

WORK

AREA

WORK UNIT CODE

SYS SUB 7-DAY INSPECTION

INSPECTION

REQUIREMENTS

ELECTRICAL POWER

ON

SERVICE

IN

FIGURE CARD NO.

1-006

MCS WORK AREA 4

010 4 CA N00 1. NWO WORKSTATIONS (1A33, 1A34).

CA NA0 A. INSPECT COMPUTER SYSTEM, DIGITAL (A1), FOR EXTERNAL CLEANLINESS,

DAMAGE, AIR FLOW AND EVIDENCE OF OVERHEATING.

CA NB0 B. INSPECT KEYBOARD AND MOUSE (A2), FOR EXTERNAL CLEANLINESS, AND DAMAGE.

CA NC0 C. INSPECT DISPLAY UNITS (A3, A4, A5), FOR EXTERNAL CLEANLINESS, DAM-

AGE, AND EVIDENCE OF OVERHEATING.

005 4 CL E00 2. INSPECT PRINTER (1A22), FOR EXTERNAL CLEANLINESS, DAMAGE, AND

EVIDENCE OF OVERHEATING.

005 4 CF MD0 3. INSPECT MEDIA CONVERTER (1A23), FOR EXTERNAL CLEANLINESS, DAMAGE, AND EVIDENCE OF OVERHEATING.

4. NOTIFY JOB CONTROL AND CREW COMMANDER OF ANY DISCREPAN-

CIES NOTED DURING INSPECTION.

(REVERSE BLANK)

CARD NO.

1-006

WORK AREA(S)

TYPE MECH RQR MECH NO. CARD TIME

00:20

PUBLICATION NUMBER

INSPECTION REQUIREMENTS

7-DAY INSPECTION

1-006

2-001

WORK AREA(S)

TYPE MECH RQR MECH NO. CARD TIME

00:40

PUBLICATION NUMBER

TO 31S5-2FSQ217-6WC-1

CHANGE NO.

MAN

MIN

WORK

AREA

WORK UNIT CODE

SYS SUB 28-DAY SERVICING

INSPECTION

REQUIREMENTS

ELECTRICAL POWER

ON

SERVICE

IN

FIGURE CARD NO.

2-001

MCS WORK AREA 1

1. PRELIMINARY ACTIONS.

CAUTION

ENSURE THE SERVICING CLOTH IS ONLY DAMP. DETERGENT MUST NOT

RUN FROM THE CLOTH WHILE WIPING EQUIPMENT. EXCESSIVE MOISTURE

WILL CAUSE ARCING AND SHORTING OF POWER.

NOTE

CLEANING CLOTHS SHALL BE DISPOSED OF IN PROPER CONTAINER.

A. EQUIPMENT NEEDED:

ANTI-STATIC VACUUM CLEANER

LINT-FREE CLOTHS

BUCKET, WATER, DETERGENT

MONITOR ANTI-STATIC CLEANING KIT

COMMON SCREWDRIVER

B. COORDINATE SERVICING TASKS WITH JOB CONTROL AND CREW COMMANDER. FAILURE

TO DO SO CAN RESULT IN LOSS OF MISSION EFFECTIVENESS.

(CONTINUED ON BACK)

CARD NO.

2-001

WORK AREA(S)

TYPE MECH RQR MECH NO. CARD TIME

00:40

PUBLICATION NUMBER

WORK

AREA

WORK UNIT CODE

SYS SUB 28-DAY SERVICING

INSPECTION

REQUIREMENTS

ELECTRICAL POWER

ON

SERVICE

IN

FIGURE CARD NO.

2-001

(CONTINUED FROM FRONT)

030 1 2. EQUIPMENT RACK 3A56.

A. USING A LINT-FREE CLOTH AND MILD DETERGENT, CLEAN EXTERIOR OF RACK.

B. USING A VACUUM CLEANER, VACUUM DIRT AND DUST IN AND AROUND EQUIPMENT.

C. OPEN EQUIPMENT RACK FRONT AND REAR DOORS.

WARNING

AVOID CONTACT WITH MOVING BLOWER FAN.

D. REMOVE TWO SCREWS SECURING THE GRILL TO THE FRONT OF THE BLOWER IN THE

RACK. REMOVE THE GRILL. REMOVE THE FILTER LOCATED BEHIND THE GRILL.

E. CLEAN THE FILTER.

(1) USING WARM WATER, WASH FILTERS TO REMOVE DIRT AND DUST.

(2) RINSE IN CLEAR WATER.

(3) SHAKE OFF EXCESS WATER AND PAT DRY WITH LINT-FREE CLOTH.

(4) ALLOW FILTER TO DRY (IN DIRECT SUNLIGHT, IF POSSIBLE).

(5) REPLACE THE FILTER AND SECURE THE GRILL TO THE BLOWER IN EACH RACK.

F. USING LINT-FREE CLOTH AND VACUUM CLEANER, CLEAN INTERIOR OF RACK.

(1) VACUUM AND OR WIPE AWAY ACCUMULATIONS OF DIRT AND DUST

IN CRACKS, CORNERS AND CREVICES.

(2) VACUUM CABLE BUNDLES CAREFULLY.

2-002

WORK AREA(S)

TYPE MECH RQR MECH NO. CARD TIME

00:40

PUBLICATION NUMBER

TO 31S5-2FSQ217-6WC-1

CHANGE NO.

MAN

MIN

WORK

AREA

WORK UNIT CODE

SYS SUB 28-DAY SERVICING

INSPECTION

REQUIREMENTS

ELECTRICAL POWER

ON

SERVICE

IN

FIGURE CARD NO.

2-002

(CONTINUED FROM PREVIOUS CARD

CAUTION

WHEN SLIDING EQUIPMENT CHASSIS OUT OF THE RACK, CHECK THE CABLE

TO PREVENT BINDING AT THE REAR OF THE EQUIPMENT.

(3) SLIDE OUT INDIVIDUAL EQUIPMENT CHASSIS AS NECESSARY FOR ACCESS.

(4) WIPE EXTERIOR OF EACH PIECE OF EQUIPMENT WITH A LINT-FREE CLOTH.

(5) VACUUM INTERIOR OF EACH RACK BLOWER.

G. REPLACE THE FILTER AND GRILL IN THE RACK AND SECURE TO THE FRONT

OF THE BLOWER USING TWO SCREWS.

H. CLOSE THE FRONT AND REAR DOORS.

010 3. PERFORM OPERATIONS CHECK PRIOR TO TURNING OVER CONTROL.

4. NOTIFY JOB CONTROL AND CREW COMMANDER THAT THE 28-DAY SERVICING IS COMPLETE.

(REVERSE BLANK)

CARD NO.

2-002

WORK AREA(S)

TYPE MECH RQR MECH NO. CARD TIME

00:40

PUBLICATION NUMBER

INSPECTION REQUIREMENTS

28-DAY SERVICING

2-002

2-003

WORK AREA(S)

TYPE MECH RQR MECH NO. CARD TIME

06:50

PUBLICATION NUMBER

TO 31S5-2FSQ217-6WC-1

CHANGE NO.

MAN

MIN

WORK

AREA

WORK UNIT CODE

SYS SUB 28-DAY SERVICING

INSPECTION

REQUIREMENTS

ELECTRICAL POWER

ON

SERVICE

IN

FIGURE CARD NO.

2-003

MCS WORK AREA 2

1. PRELIMINARY ACTIONS.

CAUTION

ENSURE THE SERVICING CLOTH IS ONLY DAMP. DETERGENT MUST NOT

RUN FROM THE CLOTH WHILE WIPING EQUIPMENT. EXCESSIVE MOISTURE

WILL CAUSE ARCING AND SHORTING OF POWER.

NOTE

CLEANING CLOTHS SHALL BE DISPOSED OF IN PROPER CONTAINER.

A. EQUIPMENT NEEDED:

ANTI-STATIC VACUUM CLEANER

LINT-FREE CLOTHS

MONITOR ANTI-STATIC CLEANING KIT

BUCKET

DETERGENT

WATER

B. COORDINATE SERVICING TASKS WITH JOB CONTROL AND CREW COMMANDER. FAILURE

TO DO SO CAN RESULT IN LOSS OF MISSION EFFECTIVENESS.

(CONTINUED ON BACK)

CARD NO.

2-003

WORK AREA(S)

TYPE MECH RQR MECH NO. CARD TIME

06:50

PUBLICATION NUMBER

WORK

AREA

WORK UNIT CODE

SYS SUB 28-DAY SERVICING

INSPECTION

REQUIREMENTS

ELECTRICAL POWER

ON

SERVICE

IN

FIGURE CARD NO.

2-003

(CONTINUED FROM FRONT)

025 2 CA C00 2. NETWORK MANAGER WORKSTATION (1A13) CLEANING.

CA CA0 A. USING A LINT-FREE CLOTH AND MILD DETERGENT, CLEAN EXTERIOR OF

COMPUTER SYSTEM, DIGITAL (A1).

CA CB0 B. KEYBOARD AND MOUSE (A2).

(1) UNPLUG AND DISASSEMBLE THE MOUSE AND CLEAN BOTH THE BALL AND

THE ROLLER BARS USING A CLEAN LINT-FREE CLOTH.

(2) REASSEMBLE THE MOUSE AND CLEAN SURFACE OF THE MOUSE USING A CLEAN

LINT-FREE CLOTH. CONNECT THE MOUSE TO THE KEYBOARD.

(3) USING A VACUUM CLEANER, VACUUM ACCUMULATIONS OF DIRT AND DUST IN

CRACKS, CORNERS AND CREVICES IN THE KEYBOARD.

CA CD0 C. USING THE MONITOR ANTI-STATIC CLEANING KIT, CLEAN THE DISPLAY UNIT (A3).

CA CE0 D. USING A LINT-FREE CLOTH AND MILD DETERGENT, CLEAN EXTERIOR

OF EXTERNAL CD-RW (A6).

CQ A00 E. USING A LINT-FREE CLOTH AND MILD DETERGENT, CLEAN EXTERIOR OF TAPE DRIVE (1A14).

F. USING A VACUUM CLEANER, VACUUM ACCUMULATIONS OF DIRT AND DUST IN CRACKS,

CORNERS AND CREVICES IN THE WORKSTATION AREA.

2-004

WORK AREA(S)

TYPE MECH RQR MECH NO. CARD TIME

06:50

PUBLICATION NUMBER

TO 31S5-2FSQ217-6WC-1

CHANGE NO.

MAN

MIN

WORK

AREA

WORK UNIT CODE

SYS SUB 28-DAY SERVICING

INSPECTION

REQUIREMENTS

ELECTRICAL POWER

ON

SERVICE

IN

FIGURE CARD NO.

2-004

(CONTINUED FROM PREVIOUS CARD

240 2 CA B00 3. COSE WORKSTATION (1A1 - 1A12) CLEANING.

CA BA0 A. USING A LINT-FREE CLOTH AND MILD DETERGENT, CLEAN EXTERIOR OF

COMPUTER SYSTEM, DIGITAL (A1).

CA BB0 B. KEYBOARD AND MOUSE (A2).

(1) UNPLUG AND DISASSEMBLE THE MOUSE AND CLEAN BOTH THE BALL AND

THE ROLLER BARS USING A CLEAN LINT-FREE CLOTH.

(2) REASSEMBLE THE MOUSE AND CLEAN SURFACE OF THE MOUSE USING A CLEAN

LINT-FREE CLOTH. CONNECT THE MOUSE TO THE KEYBOARD.

(3) USING A VACUUM CLEANER, VACUUM ACCUMULATIONS OF DIRT AND DUST IN

CRACKS, CORNERS AND CREVICES IN THE KEYBOARD.

CA BD0 C. USING THE MONITOR ANTI-STATIC CLEANING KIT, CLEAN THE DISPLAY UNITS (A3, A4, A5).

D. USING A VACUUM CLEANER, VACUUM ACCUMULATIONS OF DIRT AND DUST IN CRACKS,

CORNERS AND CREVICES IN THE WORKSTATION AREA.

055 2 4. MOW/TAT2 SYSTEM EQUIPMENT CLEANING.

CA PA0 A. USING A LINT-FREE CLOTH AND MILD DETERGENT, CLEAN EXTERIOR

OF MOW WORKSTATION (1A70).

CA PB0 B. USING A LINT-FREE CLOTH AND MILD DETERGENT, CLEAN EXTERIOR

OF KEYBOARD AND MOUSE.

(CONTINUED ON BACK)

CARD NO.

2-004

WORK AREA(S)

TYPE MECH RQR MECH NO. CARD TIME

06:50

PUBLICATION NUMBER

WORK

AREA

WORK UNIT CODE

SYS SUB 28-DAY SERVICING

INSPECTION

REQUIREMENTS

ELECTRICAL POWER

ON

SERVICE

IN

FIGURE CARD NO.

2-004

(CONTINUED FROM FRONT)

CA PC0 C. USING THE MONITOR ANTI-STATIC CLEANING KIT, CLEAN THE DISPLAY UNIT (1A75).

CA PA0 D. USING A LINT-FREE CLOTH AND MILD DETERGENT, CLEAN EXTERIOR

OF TAT2 WORKSTATION (1A71).

DE JA0 E. USING A LINT-FREE CLOTH AND MILD DETERGENT, CLEAN EXTERIOR OF KVM SWITCH (1A74).

DE JB0 F. USING A LINT-FREE CLOTH AND MILD DETERGENT, CLEAN EXTERIOR OF

PRINTER A/B SWITCH (1A72).

CQ L00 G. USING A LINT-FREE CLOTH AND MILD DETERGENT, CLEAN EXTERIOR OF TAPE DRIVE (1A76).

CL F00 H. USING A LINT-FREE CLOTH AND MILD DETERGENT, CLEAN EXTERIOR OF PRINTER (1A73).

I. USING A VACUUM CLEANER, VACUUM ACCUMULATIONS OF DIRT AND DUST IN CRACKS,

CORNERS AND CREVICES IN THE SYSTEM EQUIPMENT AREA.

020 2 CA K00 5. ALMANAC PC (1A68) CLEANING.

CA KA0 A. USING A LINT-FREE CLOTH AND MILD DETERGENT, CLEAN EXTERIOR OF

COMPUTER SUBASSEMBLY, DIGITAL (A1).

CA

CA

KB0

KD0

B. USING A LINT-FREE CLOTH AND MILD DETERGENT, CLEAN EXTERIOR OF

KEYBOARD AND MOUSE (A3, A4).

CA KC0 C. USING THE MONITOR ANTI-STATIC CLEANING KIT, CLEAN THE DISPLAY UNIT (A2).

D. USING A VACUUM CLEANER, VACUUM ACCUMULATIONS OF DIRT AND DUST IN CRACKS,

CORNERS AND CREVICES IN THE WORKSTATION AREA.

050 2 CL A00 6. PRINTERS (1A15 - 1A19) CLEANING.

A. USING A LINT-FREE CLOTH AND MILD DETERGENT, CLEAN EXTERIOR OF EQUIPMENT.

B. USING A VACUUM CLEANER, VACUUM ACCUMULATIONS OF DIRT AND DUST

IN CRACKS, CORNERS AND CREVICES.

2-005

WORK AREA(S)

TYPE MECH RQR MECH NO. CARD TIME

06:50

PUBLICATION NUMBER

TO 31S5-2FSQ217-6WC-1

CHANGE NO.

MAN

MIN

WORK

AREA

WORK UNIT CODE

SYS SUB 28-DAY SERVICING

INSPECTION

REQUIREMENTS

ELECTRICAL POWER

ON

SERVICE

IN

FIGURE CARD NO.

2-005

(CONTINUED FROM PREVIOUS CARD

010 2 CL C00 7. PRINTER (1A20) CLEANING.

A. USING A LINT-FREE CLOTH AND MILD DETERGENT, CLEAN EXTERIOR OF EQUIPMENT.

B. USING A VACUUM CLEANER, VACUUM ACCUMULATIONS OF DIRT AND DUST

IN CRACKS, CORNERS AND CREVICES.

010 8. PERFORM OPERATIONS CHECK PRIOR TO TURNING BACK TO OPERATIONS.

9. NOTIFY JOB CONTROL AND CREW COMMANDER THAT THE 28-DAY SERVICING IS COMPLETE.

(REVERSE BLANK)

CARD NO.

2-005

WORK AREA(S)

TYPE MECH RQR MECH NO. CARD TIME

06:50

PUBLICATION NUMBER

INSPECTION REQUIREMENTS

28-DAY SERVICING

2-005

2-006

WORK AREA(S)

TYPE MECH RQR MECH NO. CARD TIME

08:00

PUBLICATION NUMBER

TO 31S5-2FSQ217-6WC-1

CHANGE NO.

MAN

MIN

WORK

AREA

WORK UNIT CODE

SYS SUB 28-DAY SERVICING

INSPECTION

REQUIREMENTS

ELECTRICAL POWER

ON

SERVICE

IN

FIGURE CARD NO.

2-006

MCS WORK AREA 3

1. PRELIMINARY ACTIONS.

CAUTION

ENSURE THE SERVICING CLOTH IS ONLY DAMP. DETERGENT MUST NOT

RUN FROM THE CLOTH WHILE WIPING EQUIPMENT. EXCESSIVE MOISTURE

WILL CAUSE ARCING AND SHORTING OF POWER.

NOTE

CLEANING CLOTHS SHALL BE DISPOSED OF IN PROPER CONTAINER.

A. EQUIPMENT NEEDED:

ANTI-STATIC VACUUM CLEANER

LINT-FREE CLOTHS

MONITOR ANTI-STATIC CLEANING KIT

BUCKET, WATER, DETERGENT

COMMON SCREWDRIVER

B. COORDINATE SERVICING TASKS WITH JOB CONTROL AND CREW COMMANDER. FAILURE

TO DO SO CAN RESULT IN LOSS OF MISSION EFFECTIVENESS.

(CONTINUED ON BACK)

CARD NO.

2-006

WORK AREA(S)

TYPE MECH RQR MECH NO. CARD TIME

08:00

PUBLICATION NUMBER

WORK

AREA

WORK UNIT CODE

SYS SUB 28-DAY SERVICING

INSPECTION

REQUIREMENTS

ELECTRICAL POWER

ON

SERVICE

IN

FIGURE CARD NO.

2-006

(CONTINUED FROM FRONT)

020 3 CA C00 2. SYSTEM ADMINISTRATION WORKSTATION (3A18) CLEANING.

CA CA0 A. USING A LINT-FREE CLOTH AND MILD DETERGENT, CLEAN EXTERIOR OF

COMPUTER SYSTEM, DIGITAL (A1).

CA CB0 B. KEYBOARD AND MOUSE (A2).

(1) UNPLUG AND DISASSEMBLE THE MOUSE AND CLEAN BOTH THE BALL AND

THE ROLLER BARS USING A CLEAN LINT-FREE CLOTH.

(2) REASSEMBLE THE MOUSE AND CLEAN SURFACE OF THE MOUSE USING A CLEAN

LINT-FREE CLOTH. CONNECT THE MOUSE TO THE KEYBOARD.

(3) USING A VACUUM CLEANER, VACUUM ACCUMULATIONS OF DIRT

AND DUST IN THE KEYBOARD.

CA CD0 C. USING THE MONITOR ANTI-STATIC CLEANING KIT, CLEAN THE DISPLAY UNIT (A3).

CA CE0 D. USING A LINT-FREE CLOTH AND MILD DETERGENT, CLEAN EXTERIOR

OF EXTERNAL CD-RW (A6).

CQ A00 E. USING A LINT-FREE CLOTH AND MILD DETERGENT, CLEAN EXTERIOR OF TAPE DRIVE (3A19).

F. USING A VACUUM CLEANER, VACUUM ACCUMULATIONS OF DIRT AND DUST IN CRACKS,

CORNERS AND CREVICES IN THE WORKSTATION AREA.

040 3 CL D00 3. CRYPTO #1 & # 2 TERMINALS (3A25, 3A26), SYSTEM MAINTENANCE TER-

MINALS (3A27, 3A28) CLEANING.

A. USING A LINT-FREE CLOTH AND MILD DETERGENT, CLEAN EXTERIOR OF EQUIPMENT.

B. USING A VACUUM CLEANER, VACUUM ACCUMULATIONS OF DIRT AND DUST IN CRACKS,

CORNERS AND CREVICES OF TERMINALS AND IN AREA AROUND TERMINALS.

2-007

WORK AREA(S)

TYPE MECH RQR MECH NO. CARD TIME

08:00

PUBLICATION NUMBER

TO 31S5-2FSQ217-6WC-1

CHANGE NO.

MAN

MIN

WORK

AREA

WORK UNIT CODE

SYS SUB 28-DAY SERVICING

INSPECTION

REQUIREMENTS

ELECTRICAL POWER

ON

SERVICE

IN

FIGURE CARD NO.

2-007

(CONTINUED FROM PREVIOUS CARD

010 3 CL A00 4. PRINTER (3A24) CLEANING.

A. USING A LINT-FREE CLOTH AND MILD DETERGENT, CLEAN EXTERIOR OF EQUIPMENT.

B. USING A VACUUM CLEANER, VACUUM ACCUMULATIONS OF DIRT AND DUST

IN CRACKS, CORNERS AND CREVICES.

040 3 CA D00 5. ARTS #1 & #2 WORKSTATIONS (3A52, 3A53) CLEANING.

CA DA0 A. USING A LINT-FREE CLOTH AND MILD DETERGENT, CLEAN EXTERIOR OF

COMPUTER SYSTEM, DIGITAL (A1).

CA DB0 B. KEYBOARD AND MOUSE (A2) CLEANING.

(1) UNPLUG AND DISASSEMBLE THE MOUSE AND CLEAN BOTH THE BALL AND

THE ROLLER BARS USING A CLEAN LINT-FREE CLOTH.

(2) REASSEMBLE THE MOUSE AND CLEAN SURFACE OF THE MOUSE USING A CLEAN

LINT-FREE CLOTH. CONNECT THE MOUSE TO THE KEYBOARD.

(3) USING A VACUUM CLEANER, VACUUM ACCUMULATIONS OF DIRT

AND DUST IN THE KEYBOARD.

CA DE0 C. USING THE MONITOR ANTI-STATIC CLEANING KIT, CLEAN THE DISPLAY UNIT (A3).

(CONTINUED ON BACK)

CARD NO.

2-007

WORK AREA(S)

TYPE MECH RQR MECH NO. CARD TIME

08:00

PUBLICATION NUMBER

WORK

AREA

WORK UNIT CODE

SYS SUB 28-DAY SERVICING

INSPECTION

REQUIREMENTS

ELECTRICAL POWER

ON

SERVICE

IN

FIGURE CARD NO.

2-007

(CONTINUED FROM FRONT)

CA DD0 D. USING A LINT-FREE CLOTH AND MILD DETERGENT, CLEAN EXTERIOR OF

PASSIVE F/O TRANSCEIVER (A5).

E. USING A VACUUM CLEANER, VACUUM ACCUMULATIONS OF DIRT AND DUST IN

CRACKS, CORNERS AND CREVICES OF WORKSTATION AREAS.

040 3 CA E00 6. OPS TRANSFER # 1 AND #2 WORKSTATIONS (3A54, 3A55) CLEANING.

CA EA0 A. USING A LINT-FREE CLOTH AND MILD DETERGENT, CLEAN EXTERIOR OF

COMPUTER SYSTEM, DIGITAL (A1).

CA EB0 B. KEYBOARD AND MOUSE (A2) CLEANING.

(1) UNPLUG AND DISASSEMBLE THE MOUSE AND CLEAN BOTH THE BALL AND

THE ROLLER BARS USING A CLEAN LINT-FREE CLOTH.

(2) REASSEMBLE THE MOUSE AND CLEAN SURFACE OF THE MOUSE USING A CLEAN

LINT-FREE CLOTH. CONNECT THE MOUSE TO THE KEYBOARD.

(3) USING A VACUUM CLEANER, VACUUM ACCUMULATIONS OF DIRT

AND DUST IN THE KEYBOARD.

CA ED0 C. USING THE MONITOR ANTI-STATIC CLEANING KIT, CLEAN THE DISPLAY UNIT (A3).

D. USING A VACUUM CLEANER, VACUUM ACCUMULATIONS OF DIRT AND DUST IN

CRACKS, CORNERS AND CREVICES OF WORKSTATION AREAS.

2-008

WORK AREA(S)

TYPE MECH RQR MECH NO. CARD TIME

08:00

PUBLICATION NUMBER

TO 31S5-2FSQ217-6WC-1

CHANGE NO.

MAN

MIN

WORK

AREA

WORK UNIT CODE

SYS SUB 28-DAY SERVICING

INSPECTION

REQUIREMENTS

ELECTRICAL POWER

ON

SERVICE

IN

FIGURE CARD NO.

2-008

(CONTINUED FROM PREVIOUS CARD

020 3 CA C00 7. LAB CONTROLLER WORKSTATION (3A20) CLEANING.

CA CA0 A. USING A LINT-FREE CLOTH AND MILD DETERGENT, CLEAN EXTERIOR OF

COMPUTER SYSTEM, DIGITAL (A1).

CA CB0 B. KEYBOARD AND MOUSE (A2) CLEANING.

(1) UNPLUG AND DISASSEMBLE THE MOUSE AND CLEAN BOTH THE BALL AND

THE ROLLER BARS USING A CLEAN LINT-FREE CLOTH.

(2) REASSEMBLE THE MOUSE AND CLEAN SURFACE OF THE MOUSE USING A CLEAN

LINT-FREE CLOTH. CONNECT THE MOUSE TO THE KEYBOARD.

(3) USING A VACUUM CLEANER, VACUUM ACCUMULATIONS OF DIRT

AND DUST IN THE KEYBOARD.

CA CD0 C. USING THE MONITOR ANTI-STATIC CLEANING KIT, CLEAN THE DISPLAY UNIT (A3).

CQ B00 D. USING A LINT-FREE CLOTH AND MILD DETERGENT, CLEAN EXTERIOR OF

LAB CONTROLLER D2 RAID (3A21).

CQ F00 E. USING A LINT-FREE CLOTH AND MILD DETERGENT, CLEAN EXTE-

RIOR OF TAPE LIBRARY (3A16).

F. USING A VACUUM CLEANER, VACUUM ACCUMULATIONS OF DIRT AND DUST IN

CRACKS, CORNERS AND CREVICES OF WORKSTATION AREA.

(CONTINUED ON BACK)

CARD NO.

2-008

WORK AREA(S)

TYPE MECH RQR MECH NO. CARD TIME

08:00

PUBLICATION NUMBER

WORK

AREA

WORK UNIT CODE

SYS SUB 28-DAY SERVICING

INSPECTION

REQUIREMENTS

ELECTRICAL POWER

ON

SERVICE

IN

FIGURE CARD NO.

2-008

(CONTINUED FROM FRONT)

255 3 8. EQUIPMENT RACKS (3A3 - 3A13, 3A29, 3A37 - 3A42, 3A59, 3A65, 3A68) CLEANING.

A. USING A LINT-FREE CLOTH AND MILD DETERGENT, CLEAN EXTERIOR OF EQUIPMENT.

B. USING A VACUUM CLEANER, VACUUM ACCUMULATIONS OF DIRT AND DUST

IN CRACKS, CORNERS AND CREVICES.

C. OPEN EQUIPMENT RACK FRONT AND REAR DOORS.

WARNING

AVOID CONTACT WITH MOVING BLOWER FAN.

NOTE

STEPS D, E AND G DO NOT APPLY TO RACK 3A68.

D. REMOVE TWO SCREWS SECURING THE GRILL TO THE FRONT OF THE BLOWER IN THE

RACK. REMOVE THE GRILL. REMOVE THE FILTER LOCATED BEHIND THE GRILL.

E. CLEAN THE FILTER.

(1) USING WARM WATER, WASH FILTERS TO REMOVE DIRT AND DUST.

(2) RINSE IN CLEAR WATER.

(3) SHAKE OFF EXCESS WATER AND PAT DRY WITH LINT-FREE CLOTH.

(4) ALLOW FILTER TO DRY (IN DIRECT SUNLIGHT, IF POSSIBLE).

(5) REPLACE THE FILTER AND SECURE THE GRILL TO THE BLOWER IN EACH RACK.

2-009

WORK AREA(S)

TYPE MECH RQR MECH NO. CARD TIME

08:00

PUBLICATION NUMBER

TO 31S5-2FSQ217-6WC-1

CHANGE NO.

MAN

MIN

WORK

AREA

WORK UNIT CODE

SYS SUB 28-DAY SERVICING

INSPECTION

REQUIREMENTS

ELECTRICAL POWER

ON

SERVICE

IN

FIGURE CARD NO.

2-009

(CONTINUED FROM PREVIOUS CARD

F. USING LINT-FREE CLOTH AND VACUUM CLEANER, CLEAN INTERIOR OF RACK.

(1) VACUUM AND OR WIPE AWAY ACCUMULATIONS OF DIRT AND DUST

IN CRACKS, CORNERS AND CREVICES.

(2) VACUUM CABLE BUNDLES CAREFULLY.

CAUTION

WHEN SLIDING EQUIPMENT CHASSIS OUT OF THE RACK, CHECK THE CABLE

TO PREVENT BINDING AT THE REAR OF THE EQUIPMENT.

(3) SLIDE OUT INDIVIDUAL EQUIPMENT CHASSIS AS NECESSARY FOR ACCESS.

(4) WIPE EXTERIOR OF EACH PIECE OF EQUIPMENT WITH A LINT-FREE CLOTH.

(5) VACUUM INTERIOR OF EACH RACK BLOWER (EXCEPT 3A68).

G. REPLACE THE FILTER AND GRILL IN THE RACK AND SECURE TO THE FRONT

OF THE BLOWER USING TWO SCREWS.

H. CLOSE THE FRONT AND REAR DOORS.

010 9. PERFORM OPERATIONS CHECK PRIOR TO TURNING BACK TO OPERATIONS.

10.NOTIFY JOB CONTROL AND CREW COMMANDER THAT THE 28-DAY SERVICING IS COMPLETE.

(REVERSE BLANK)

CARD NO.

2-009

WORK AREA(S)

TYPE MECH RQR MECH NO. CARD TIME

08:00

PUBLICATION NUMBER

INSPECTION REQUIREMENTS

28-DAY SERVICING

2-009

2-010

WORK AREA(S)

TYPE MECH RQR MECH NO. CARD TIME

01:05

PUBLICATION NUMBER

TO 31S5-2FSQ217-6WC-1

CHANGE NO.

MAN

MIN

WORK

AREA

WORK UNIT CODE

SYS SUB 28-DAY SERVICING

INSPECTION

REQUIREMENTS

ELECTRICAL POWER

ON

SERVICE

IN

FIGURE CARD NO.

2-010

MCS WORK AREA 4

1. PRELIMINARY ACTIONS.

CAUTION

ENSURE THE SERVICING CLOTH IS ONLY DAMP. DETERGENT MUST NOT

RUN FROM THE CLOTH WHILE WIPING EQUIPMENT. EXCESSIVE MOISTURE

WILL CAUSE ARCING AND SHORTING OF POWER.

NOTE

CLEANING CLOTHS SHALL BE DISPOSED OF IN PROPER CONTAINER.

A. EQUIPMENT NEEDED:

ANTI-STATIC VACUUM CLEANER

LINT-FREE CLOTHS

MONITOR ANTI-STATIC CLEANING KIT

BUCKET

DETERGENT

WATER

B. COORDINATE SERVICING TASKS WITH JOB CONTROL AND CREW COMMANDER. FAILURE

TO DO SO CAN RESULT IN LOSS OF MISSION EFFECTIVENESS.

(CONTINUED ON BACK)

CARD NO.

2-010

WORK AREA(S)

TYPE MECH RQR MECH NO. CARD TIME

01:05

PUBLICATION NUMBER

WORK

AREA

WORK UNIT CODE

SYS SUB 28-DAY SERVICING

INSPECTION

REQUIREMENTS

ELECTRICAL POWER

ON

SERVICE

IN

FIGURE CARD NO.

2-010

(CONTINUED FROM FRONT)

030 4 CA N00 2. NWO WORKSTATIONS (1A34, 1A33) CLEANING.

CA NA0 A. USING A LINT-FREE CLOTH AND MILD DETERGENT, CLEAN EXTERIOR OF

COMPUTER SYSTEM, DIGITAL (A1).

CA NB0 B. USING A LINT-FREE CLOTH AND MILD DETERGENT, CLEAN EXTERIOR OF

KEYBOARD AND MOUSE (A2).

CA NC0 C. USING THE MONITOR ANTI-STATIC CLEANING KIT, CLEAN THE DISPLAY UNITS (A3, A4, A5).

D. USING A VACUUM CLEANER, VACUUM ACCUMULATIONS OF DIRT AND DUST IN

CRACKS, CORNERS AND CREVICES IN WORKSTATION AREAS.

020 4 CL E00 3. PRINTER (1A22) CLEANING.

A. USING A LINT-FREE CLOTH AND MILD DETERGENT, CLEAN EXTERIOR OF EQUIPMENT.

B. USING A VACUUM CLEANER, VACUUM ACCUMULATIONS OF DIRT AND DUST

IN CRACKS, CORNERS AND CREVICES.

010 4 CF MD0 4. MEDIA CONVERTER (1A23) CLEANING

A. USING A LINT-FREE CLOTH AND MILD DETERGENT, CLEAN EXTERIOR OF EQUIPMENT.

005 5. PERFORM OPERATIONS CHECK PRIOR TO TURNING BACK TO OPERATIONS.

6. NOTIFY JOB CONTROL AND CREW COMMANDER THAT THE 28-DAY SERVICING IS COMPLETE.

2-011

WORK AREA(S)

TYPE MECH RQR MECH NO. CARD TIME

00:25

PUBLICATION NUMBER

TO 31S5-2FSQ217-6WC-1

CHANGE NO.

MAN

MIN

WORK

AREA

WORK UNIT CODE

SYS SUB 28-DAY SERVICING

INSPECTION

REQUIREMENTS

ELECTRICAL POWER SERVICE

IN

FIGURE CARD NO.

2-011

KI-17 BENCH STOCK BATTERY RECHARGING

1. PRELIMINARY ACTIONS.

A. EQUIPMENT NEEDED:

BENCH STOCK KI-17 BATTERIES

BATTERY CHARGER

B. RETRIEVE BATTERIES FROM BENCH STOCK.

025 2. KI-17 BENCH STOCK BATTERY RECHARGING

NOTE

NI-CAD BATTERIES LOSE THEIR CHARGE AT APPROX. 1%/DAY AND MUST BE

PERIODICALLY CHARGED TO ENSURE THEY ARE ALWAYS READY TO BE INSTALLED.

A. PLUG PANASONIC BQ-4D CHARGER INTO STANDARD 110-120 VOLT AC OUTLET.

(CONTINUED ON BACK)

CARD NO.

2-011

WORK AREA(S)

TYPE MECH RQR MECH NO. CARD TIME

00:25

PUBLICATION NUMBER

WORK

AREA

WORK UNIT CODE

SYS SUB 28-DAY SERVICING

INSPECTION

REQUIREMENTS

ELECTRICAL POWER SERVICE

IN

FIGURE CARD NO.

2-011

(CONTINUED FROM FRONT)

NOTE

• BE SURE TO PROPERLY MATE EACH BATTERY SIDES WITH ITS PROPER

TERMINAL INSIDE THE CHARGER COMPARTMENT.

• INDICATOR LIGHT SHOULD COME ON FOR EACH COMPARTMENT THAT IS

LOADED, INDICATING THAT CHARGING IS OCCURING.

B. LOAD BATTERIES INTO CHARGING COMPARTMENT (BATTERIES MUST AL-

WAYS BE CHARGED IN IDENTICAL PAIRS).

NOTE

• BATTERIES CAN BE REMOVED EARLIER THAN INDICATED, BUT AVAILABLE

BATTERY POWER WILL BE REDUCED PROPORTIONATELY.

• RED CHARGING INDICATOR LIGHTS DO NOT GO OUT WHEN CHARGING TIME IS

OVER. BATTERIES CAN BE LEFT IN CHARGING UNIT WITHOUT HARM, BUT FOR

MAXIMUM BATTERY LIFE, REMOVE THE BATTERIES AFTER FULLY CHARGING.

C. CHARGE BATTERY FOR APPROXIMATELY SIX HOURS.

3. POST SERVICING ACTIONS.

A. RETURN RECHARGED BATTERIES TO BENCH STOCK.

B. NOTIFY JOB CONTROL AND CREW COMMANDER THAT THE 28-DAY SERVICING IS COMPLETE.

3-001

WORK AREA(S)

2, 3

TYPE MECH RQR MECH NO. CARD TIME

00:20

PUBLICATION NUMBER

TO 31S5-2FSQ217-6WC-1

CHANGE NO.

MAN

MIN

WORK

AREA

WORK UNIT CODE

SYS SUB 84-DAY SERVICING

INSPECTION

REQUIREMENTS

ELECTRICAL POWER

ON

SERVICE

IN

FIGURE CARD NO.

3-001

TAPE DRIVES (1A14, 3A7A2, 3A7A3, 3A16, 3A19)

020 1. PRELIMINARY ACTIONS.

A. REQUIRED EQUIPMENT.

TAPE DRIVE CLEANING CARTRIDGE (3A16 USES P/N: 315205) (1A14, 3A19,

3A7A2 AND 3A7A3 USE PN: 386445).

B. IF THE POWER IS OFF, TURN THE POWER TO THE TAPE DRIVE UNIT ON. WHEN THE

POWER CYCLE IS COMPLETE, REMOVE ANY DATA CARTRIDGE IN THE UNIT.

(CONTINUED ON BACK)

CARD NO.

3-001

WORK AREA(S)

2, 3

TYPE MECH RQR MECH NO. CARD TIME

00:20

PUBLICATION NUMBER

WORK

AREA

WORK UNIT CODE

SYS SUB 84-DAY SERVICING

INSPECTION

REQUIREMENTS

ELECTRICAL POWER

ON

SERVICE

IN

FIGURE CARD NO.

3-001

(CONTINUED FROM FRONT)

CAUTION

IF THE CLEANING CARTRIDGE IS EJECTED FROM THE DRIVE WITHOUT PERFORMING

THE CLEANING PROCESS, OR IF THERE IS NO CLEANING FABRIC REMAINING

ON THE SUPPLY REEL, THE CLEANING CARTRIDGE HAS REACHED THE END

OF ITS USEFUL LIFE. DISCARD AND USE A NEW CLEANING CARTRIDGE. DO

NOT REWIND AND REUSE THE CLEANING CARTRIDGE.

2. CLEANING

2, 3 CQ

CQ

CQ

A00 C00 F00

A. PLACE THE CLEANING CARTRIDGE INTO THE DRIVE.

NOTE

THE TAPE DRIVE WILL AUTOMATICALLY PERFORM THE CLEANING PROCESS.

WHEN THE PROCESS IS COMPLETE, THE CLEANING CARTRIDGE IS

AUTOMATICALLY UNLOADED AND EJECTED.

B. WAIT FOR THE CLEANING PROCESS TO COMPLETE.

C. REPEAT PROCESS FOR EACH TAPE DRIVE.

3. POST SERVICING ACTIONS.

A. RECORD THE DATE THE CLEANINGS WERE PERFORMED ON THE CLEANING RECORD.

B. PUT THE CLEANING TAPES AWAY.

3-002

WORK AREA(S)

TYPE MECH RQR MECH NO. CARD TIME

00:20

PUBLICATION NUMBER

TO 31S5-2FSQ217-6WC-1

CHANGE NO.

MAN

MIN

WORK

AREA

WORK UNIT CODE

SYS SUB 84-DAY SERVICING

INSPECTION

REQUIREMENTS

ELECTRICAL POWER

ON

SERVICE

IN

FIGURE CARD NO.

3-002

TAPE DRIVE (3A7A4)

020 3 CQ D00 1. PRELIMINARY ACTIONS.

A. REQUIRED EQUIPMENT (LOCATED IN CLEANING SUPPLY COMPART-

MENT OF THE TAPE DRIVE).

Q-TIP APPLICATOR.

91% ISOPROPYL ALCOHOL.

NOTE

WHEN THE TAPE DRIVE HAS EXPERIENCED A DATA ERROR THE TAPE HEAD

SHOULD BE CLEANED AS SOON AS POSSIBLE.

B. IF THE POWER IS OFF, TURN THE POWER TO THE TAPE DRIVE UNIT ON. WHEN THE

POWER CYCLE IS COMPLETE, REMOVE ANY DATA TAPE REEL.

C. OPEN THE TAPE COMPARTMENT COVER.

D. ACCESS THE CLEANING SUPPLY COMPARTMENT AND RETRIEVE CLEANING SUPPLIES.

3 2. USING THE CLEANING SUPPLIES CLEAN FOREIGN MATERIAL FROM:

A. TWO TAPE ROLLERS.

B. TAPE CLEANING BLADES.

C. HEADS.

D. THE SUPPLY (FRONT REEL HUB).

(CONTINUED ON BACK)

CARD NO.

3-002

WORK AREA(S)

TYPE MECH RQR MECH NO. CARD TIME

00:20

PUBLICATION NUMBER

WORK

AREA

WORK UNIT CODE

SYS SUB 84-DAY SERVICING

INSPECTION

REQUIREMENTS

ELECTRICAL POWER

ON

SERVICE

IN

FIGURE CARD NO.

3-002

(CONTINUED FROM FRONT)

3 3. POST CLEANING ACTIONS.

A. RETURN CLEANING SUPPLIES TO SUPPLY COMPARTMENT.

B. CLOSE TAPE COMPARTMENT COVER.

3-003

WORK AREA(S)

TYPE MECH RQR MECH NO. CARD TIME

00:20

PUBLICATION NUMBER

TO 31S5-2FSQ217-6WC-1

CHANGE NO.

MAN

MIN

WORK

AREA

WORK UNIT CODE

SYS SUB 84-DAY SERVICING

INSPECTION

REQUIREMENTS

ELECTRICAL POWER

ON

SERVICE

IN

FIGURE CARD NO.

3-003

TAPE DRIVE (3A7A5A1, 3A7A5A2)

020 1. PRELIMINARY ACTIONS.

A. REQUIRED EQUIPMENT.

TAPE DRIVE CLEANING CARTRIDGE (PN: 309258-002).

B. IF THE POWER IS OFF, TURN THE POWER TO THE TAPE DRIVE UNIT ON. WHEN THE

POWER CYCLE IS COMPLETE, REMOVE ANY DATA CARTRIDGE IN THE UNIT.

(CONTINUED ON BACK)

CARD NO.

3-003

WORK AREA(S)

TYPE MECH RQR MECH NO. CARD TIME

00:20

PUBLICATION NUMBER

WORK

AREA

WORK UNIT CODE

SYS SUB 84-DAY SERVICING

INSPECTION

REQUIREMENTS

ELECTRICAL POWER

ON

SERVICE

IN

FIGURE CARD NO.

3-003

(CONTINUED FROM FRONT)

CAUTION

IF THE CLEANING CARTRIDGE IS EJECTED FROM THE DRIVE WITHOUT PERFORMING

THE CLEANING PROCESS, OR IF THERE IS NO CLEANING FABRIC REMAINING

ON THE SUPPLY REEL, THE CLEANING CARTRIDGE HAS REACHED THE END

OF ITS USEFUL LIFE. DISCARD AND USE A NEW CLEANING CARTRIDGE. DO

NOT REWIND AND REUSE THE CLEANING CARTRIDGE.

3 CQ E00 2. CLEANING.

A. PLACE THE CLEANING CARTRIDGE INTO THE DRIVE.

NOTE

THE TAPE DRIVE WILL AUTOMATICALLY PERFORM THE CLEANING PROCESS.

WHEN THE PROCESS IS COMPLETE, THE CLEANING CARTRIDGE IS

AUTOMATICALLY UNLOADED AND EJECTED.

B. WAIT FOR THE PROCESS TO COMPLETE.

C. REPEAT PROCESS FOR EACH TAPE DRIVE.

3. POST SERVICING ACTIONS.

A. RECORD THE DATE THE CLEANING WAS PERFORMED ON THE CLEANING RECORD.

B. PUT THE CLEANING TAPE(S) AWAY.

4-001

WORK AREA(S)

TYPE MECH RQR MECH NO. CARD TIME

00:20

PUBLICATION NUMBER

TO 31S5-2FSQ217-6WC-1

CHANGE NO.

MAN

MIN

WORK

AREA

WORK UNIT CODE

SYS SUB 546-DAY SERVICING

INSPECTION

REQUIREMENTS

ELECTRICAL POWER

ON

SERVICE

IN

FIGURE CARD NO.

4-001

KI-17 BATTERY REPLACEMENT

CAUTION

THE NICAD BATTERIES CAN BE SAFELY REMOVED FROM AN OPERATIONAL KI-17

UNIT WITHOUT INTERRUPTING OPERATIONS OR LOSS OF KEYS AND ALGORITHMS.

HOWEVER, REMOVAL OF BATTERIES WHILE THE UNIT IS POWERED DOWN WILL

RESULT IN LOSS OF ALL KEYS AND ALGORITHMS AND REQUIRE RELOADING IN

ACCORDANCE WITH PROCEDURES CONTAINED IN TO 31S5-2FSQ217-2.

NOTE

THE PURPOSE OF THIS SERVICING ACTION IS TO REPLACE THE NICAD BATTERIES

IN THE OPERATIONAL KI-17 UNITS WITH FRESH BATTERIES FROM BENCH STOCK.

NICAD BATTERIES HAVE A SHELF LIFE OF APPROXIMATELY 18 MONTHS.

015 3 1. PRELIMINARY ACTIONS.

DE DAB A. OBTAIN THE SPARE NICAD BATTERIES FROM BENCH STOCK.

B. OPEN THE FRONT DOOR OF THE COMSEC RACK (3A59).

(CONTINUED ON BACK)

CARD NO.

4-001

WORK AREA(S)

TYPE MECH RQR MECH NO. CARD TIME

00:20

PUBLICATION NUMBER

WORK

AREA

WORK UNIT CODE

SYS SUB 546-DAY SERVICING

INSPECTION

REQUIREMENTS

ELECTRICAL POWER

ON

SERVICE

IN

FIGURE CARD NO.

4-001

(CONTINUED FROM FRONT)

005 3 2. REPLACE BATTERIES IN KI-17 UNITS (3A59A1, 3A59A2, AND 3A59A3).

DE DA0 A. AT A KI-17 UNIT TURN THE BLUE BATTERY SLEEVE COUNTER-CLOCKWISE

UNTIL THREADS DISENGAGE.

B. PULL THE SLEEVE OUT OF THE UNIT.

DE DAB C. REMOVE THE BATTERIES FROM THE SLEEVE.

D. PLACETHREENICADBATTERIESOBTAINEDFROMBENCHSTOCK INTOTHEBATTERYSLEEVE.

E. INSERT THE LOADED BATTERY SLEEVE INTO THE KI-17 UNIT AND RO-

TATE CLOCKWISE UNTIL SECURE.

F. REPEAT STEPS A THROUGH E FOR THE REMAINING KI-17 UNITS.

3. POST SERVICING ACTIONS.

A. CLOSE THE FRONT DOOR OF THE COMSEC RACK (3A59).

B. DISCARD USED BATTERIES IN ACCORDANCE WITH LOCAL DISPOSAL POLICY.

C. PERFORM OPERATIONS CHECK PRIOR TO TURNING BACK TO OPERATIONS.

D. NOTIFY JOB CONTROL AND CREW COMMANDER THAT THE TIME REPLACE-

MENT ITEMS ARE COMPLETE.