31S5-2FSQ217-06.pdf

TO 31S5-2FSQ217-06

TECHNICAL MANUAL

WORK UNIT CODE MANUAL

ORGANIZATIONAL MAINTENANCE

GLOBAL POSITIONING SYSTEM (GPS)

MASTER CONTROL STATION

(MCS)/ALTERNATE MCS (AMCS)

AN/FSQ-217 (V)

HARRIS CORPORATION GOVERNMENT COMMUNICATIONS SYSTEMS DIVISION

2SC0491

This revision supersedes TO 31S5-2FSQ217-06 dated 31 October 2009 and all changes.

DISTRIBUTION STATEMENT - E - Distribution authorized to DOD components only for Administrative or Operational use (15 January 2012). Other requests shall be referred to SMC_SLG/GPL - TOMA, 1050 East Stewart Avenue, Peterson AFB, CO 80914-2902.

WARNING - This Document contains technical data whose export is restricted by the Arms Export Control Act (Title 22, USC, Sec 2751 et. seq.) or the Export Administra-tion Act of 1979, as amended (Title 50, USC, App 2401et.seq.). Violations of these export laws are subject to severe criminal penalties. Disseminate in accordance with provisions of DoD Directive 5230.25.

HANDLING AND DESTRUCTION NOTICE - Handle in compliance with the distribu-tion statement and destroy by any method that will prevent disclosure of the contents or reconstruction of the document.

Published under authority of the Secretary of the Air Force.

15 JANUARY 2012

LIST OF EFFECTIVE PAGES

INSERT LATEST CHANGED PAGES.

DESTROY SUPERSEDED PAGES.

NOTE: The portion of the text affected by the changes is indicated by a vertical line in the outer margins of the page.

Changes to illustrations are indicated by shaded or screened areas, or by miniature pointing hands. Changes to wiring diagrams are indicated by shaded areas.

Dates of issue for original and changed pages are:

Original . . . 0 . . . . 15 JANUARY 2012

TOTAL NUMBER OF PAGES IN THIS PUBLICATION IS 64 CONSISTING OF THE

FOLLOWING:

Page *Change Page *Change Title A I-001

II-001 - II-003

II-004 Blank

III-001 - III-002

IV-001 - IV-005

IV-006 Blank V-001 V-002 Blank

VI-001 - VI-004

VII-001 - VII-002

VIII-001

VIII-002 Blank

IX-001 - IX-004

X-001 - X-002

XI-001

XI-002 Blank

XII-001

XII-002 Blank 01-001 - 01-002 03-001 03-002 Blank 04-001 04-002 Blank

CA-001 - CA-005

CA-006 Blank

CF-001 - CF-003

CF-004 Blank

CL-001

CL-002 Blank

CQ-001 - CQ-002

CT-001

CT-002 Blank

CW-001

CW-002 Blank

DE-001

DE-002 Blank

DJ-001

DJ-002 Blank

*Zero in this column indicates an original page

A USAF

Table Of Contents Code Page

TABLE OF CONTENTS I-001

FOREWORD II-001

TYPE MAINTENANCE CODES III-001

ACTION TAKEN CODES IV-001

WHEN DISCOVERED CODES V-001

HOW MALFUNCTIONED CODES ALPHABETICAL

LISTING - AVIONICS/ELECTRICAL/COMPUTER VI-001

HOW MALFUNCTIONED CODES ALPHABETICAL

LISTING - PHYSICAL/MECHANICAL VII-001

HOW MALFUNCTIONED CODES ALPHABETICAL

LISTING - NO DEFECT VIII-001

HOW MALFUNCTIONED CODES NUMERICAL

LISTING - AVIONICS/ELECTRICAL/COMPUTER IX-001

HOW MALFUNCTIONED CODES NUMERICAL

LISTING - PHYSICAL/MECHANICAL X-001

HOW MALFUNCTIONED CODES NUMERICAL

LISTING - NO DEFECT XI-001

UNIQUE DATA CODES MCS

(MAINTENANCE COST SYSTEM) XII-001

SUPPORT GENERAL CODES

(EXCEPT 03000 AND 04000) 01-001

03000 SUPPORT GENERAL CODES 03-001

04000 SUPPORT GENERAL CODES 04-001

WORK UNIT CODE SYSTEM

CA MCS/AMCS CENTRAL PROCESSING SYSTEM CA-001

CF MCS/AMCS INPUT/OUTPUT CONTROL SYSTEM CF-001

CL MCS/AMCS INPUT/OUTPUT SYSTEM CL-001

CQ MCS/AMCS AUXILARY STORAGE SYSTEM CQ-001

I-001

Table Of Contents Code Page

CT MCS/AMCS POWER CONTROL & DISTRIBUTION

SYSTEM CT-001

CW MCS/AMCS DISPLAY/PROJECTION SYSTEM CW-001

DE MCS/AMCS AUXILIARY DEVICES SYSTEM DE-001

DJ MCS/AMCS INTERFACE SYSTEMS DJ-001

I-001

FOREWORD

1 GENERAL

NOTE

This manual contains baseline configuration data for KI-17 Interface Modification (KIM) Upgrade configuration.

THE COMPLETE DETAILS ON USE OF CODES PRINTED IN THIS MANUAL

ARE PRESCRIBED IN AFI 21-101 AND TO 00-20-2-SERIES TECHNICAL ORDERS.

2 USE OF CODES

IT IS NECESSARY TO USE CODES FOR RECORDING MAINTENANCE

ACTIONS IN ORDER TO CONVERT THIS INFORMATION INTO LANGUAGE FOR

TRANSLATION BY ACCOUNTING MACHINES AND COMPUTERS. THE MAIN-

TENANCE FORMS ARE SENT TO DATA AUTOMATION, AND INFORMATION

RECORDED ON THEM IS USED PERIODICALLY TO PRODUCE REPORTS

FOR USE IN THE MANAGEMENT OF THE MAINTENANCE FUNCTION, SUCH

AS DETERMINING DEFICIENT MATERIAL, FACILITIES, OR PROCEDURES.

2.1. WORK UNIT CODE. THIS CODE CONSISTS OF FIVE ALPHABETIC

AND NUMERIC CHARACTERS AND IS USED TO IDENTIFY THE SYSTEM,

SUBSYSTEM, AND COMPONENT WHICH WERE WORKED ON. FOR ITEMS NOT

OTHERWISE CODED, THE ABBREVIATION NOC IS USED. THE NUMBER 99 IS

USED IN THE FOURTH AND FIFTH CHARACTERS OF THE WORK UNIT CODE

FOLLOWED BY THE ABBREVIATION NOC AND SHOULD ONLY BE USED WHEN

AN ITEM DOES NOT HAVE A SPECIFIC WORK UNIT CODE ASSIGNED. NOTE:

COMMUNICATION-ELECTRONIC (CE) USE CODE "00NOC." AN AFTO FORM 22

MAY BE SUBMITTEDWHEN A 99NOC CODE IS USED DUE TO LACK OF AWORK

UNIT CODE FOR A REPAIRABLE ITEM. THIS MANUAL HAS BEEN PREPARED

IN TWO CHAPTERS; CHAPTER 1 CONTAINS WORK UNIT CODE - NOUN -

SYSTEM/SUBSYSTEM/ REFERENCE DESIGNATION INDEX LISTINGS FOR THE

WEAPON SYSTEM, AND SUPPORT EQUIPMENT PECULIAR TO THE WEAPON

SYSTEM. CHAPTER 2 CONTAINS SYSTEM/SUBSYSTEM/ REFERENCE

DESIGNATION INDEX - NOUN -WORK UNIT CODE LISTINGS FOR THEWEAPON

SYSTEM, AND SUPPORT EQUIPMENT PECULIAR TO THE WEAPON SYSTEM.

2.2. UNIQUE DATA CODES FOR MCS. THIS CODE CONSISTS OF FIVE

ALPHABETIC OR NUMERIC CHARACTERS, AND IS USED TO IDENTIFY DIRECT

LABOR MAN-HOURS EXPENDED IN OTHER THAN DIRECT LABOR, I.E., ALERT

DUTY, DETAIL, LEAVE, TRAINING, ETC.

2.3. TYPEMAINTENANCE CODE. THIS CODE CONSISTS OF ONE ALPHABETIC

OR NUMERIC CHARACTER, AND IDENTIFIES THE TYPE OF MAINTENANCE

BEING PERFORMED, (I.E., SCHEDULED OR UNSCHEDULED MAINTENANCE).

2.4. ACTION TAKEN CODE. THIS CODE CONSISTS OF ONE ALPHABETIC

OR NUMERIC CHARACTER, AND IDENTIFIES WHAT WORK WAS DONE, (I.E.,

REMOVED, REPLACED).

II-001

NOTE

COLLECTIVELY, THE WORK UNIT CODE AND THE ACTION

TAKEN CODE IDENTIFY A "UNIT OF WORK" AS DEFINED

IN AFI 21-101.

2.5. WHEN DISCOVERED CODE. THIS CODE CONSISTS OF ONE ALPHABETIC

OR NUMERIC CHARACTER, AND IS USED TO DESCRIBE AT WHAT TIME A

DISCREPANCY WAS DISCOVERED.

2.6. HOW MALFUNCTIONED CODE. THIS CODE CONSISTS OF THREE

NUMERIC CHARACTERS, AND IS USED TO DESCRIBE THE EQUIPMENT

MALFUNCTION.

3 SECURITY

WHEN MAINTENANCE IS BEING PERFORMED ON CLASSIFIED EQUIPMENT,

THE LISTING OF A WORK UNIT CODE COULD POSSIBLY LEAD TO A BREACH

OF SECURITY, SUCH AS BETRAYING MISSION CAPABILITY. EXTREME

CAUTION SHOULD BE EXERCISED. IF ANY QUESTION EXISTS, IT WILL BE

RESOLVED ACCORDING TO AFI 31-401 AND OTHER APPLICABLE DIRECTIVES.

4 CHANGES TO CODES

4.1. SYSTEM CODES. THE SYSTEM CODES IN THIS MANUAL ARE STANDARD

THROUGHOUT THE AIR FORCE, AND WILL ONLY BE REVISED BY OFFICIAL

PUBLICATION. RECOMMENDED CHANGES TO THIS MANUAL REGARDING ITS

USE, FORMAT, PROCEDURES, OR THE ACTION TAKEN, WHEN DISCOVERED,

HOW MALFUNCTIONED, OR SUPPORT GENERAL CODES, WILL BE

SUBMITTED THROUGH COMMAND CHANNELS.

4.2. CHANGES. RECOMMENDED CHANGES TO WORK UNIT CODES OR

EQUIPMENT LISTINGS, IN THIS MANUAL, SHALL BE SUBMITTED ON AN AFTO

FORM 22, IN ACCORDANCE WITH TO 00-5-1, TO THE FOLLOWING ADDRESS:

SMC_SLG/GPL - TOMA

1050 EAST STEWART AVENUE

PETERSON AFB, CO 80914-2902

5 COMMUNICATION ELECTRONIC (CE) ONLY

COMPLETE DETAILS ON USE OF THE CODES CONTAINED IN THIS MANUAL

ARE PRESCRIBED IN AFI 21-101 AND 00-20-2-SERIES TECHNICAL ORDERS.

NOTE

THIS WORK UNIT CODE MANUAL SHOULD ONLY BE USED

FOR REPORTINGMAINTENANCE ACTIONS ON EQUIPMENT

THAT IS A PARTOF THEAN/FSQ-141, GLOBAL POSITIONING

SYSTEM, OPERATIONAL CONTROL SEGMENT (GPS/OCS).

COMPLETE DETAILS ON USE OF THE CODES CONTAINED

IN THIS MANUAL ARE PRESCRIBED IN AFI 21-101 AND

00-20-2-SERIES TECHNICAL ORDERS.

II-002

THE COMMUNICATION ELECTRONIC (CE) SYSTEM CODES ARE AS FOLLOWS:

A. STANDARD RADAR SYSTEM CODES (Not Applicable to Navigational Radar)

AA ANTENNA SYSTEM

AE CONTROL SYSTEM

AF TEST CONTROL SYSTEM

AG INDICATOR SYSTEM

AK TRANSMITTER SYSTEM

AP RECEIVER SYSTEM

AQ DATA HANDLING SYSTEM

AT ECCM SYSTEM

AU TIMING SYSTEM

AV RF SYSTEM

AX TOWER SYSTEM

BA COMMUNICATIONS AND INTER-COMMUNICATIONS

BC IFF SYSTEM

BE OPTICS SYSTEM

BF MAPPING SYSTEM

BH SUPPORT EQUIPMENT

BK PERFORMANCE MONITOR

BM TELEVISION SYSTEM

BW MISCELLANEOUS SYSTEM

BY MULTIPLEXER SYSTEM

B. STANDARD COMPUTER SYSTEM CODES

CA CENTRAL PROCESSING SYSTEM

CF INPUT/OUTPUT CONTROL SYSTEM

CL INPUT/OUTPUT SYSTEM

CQ AUXILIARY STORAGE SYSTEM

CT POWER CONTROL AND DISTRIBUTION SYSTEM

CW DISPLAY/PROJECTION SYSTEM

DA TEST/MONITOR AND ALARM SYSTEM

DE AUXILIARY DEVICES SYSTEM

DJ INTERFACE SYSTEMS

DM SUPPORT EQUIPMENT

II-003/(II-004 blank)

TYPE MAINTENANCE CODES

CODE DEFINITION

A SERVICE: INCLUDES ALL UNITS OF WORK ASSOCIATED WITH

SERVICING, CLEANING, AND MOVEMENT OF EQUIPMENT.

B UNSCHEDULED MAINTENANCE: INCLUDES ALL UNITS OF

WORK ACCOMPLISHED BETWEEN SCHEDULED INSPECTIONS,

EXCLUDES TCTO ACCOMPLISHMENT.

D SCHEDULED INSPECTION: INCLUDES ALL UNITS OF WORK

ACCOMPLISHED DURING SCHEDULED INSPECTIONS SUCH

AS DAILY, SAFETY, AND SERVICING INSPECTION, EXCLUDING

PERIODIC/PHASED INSPECTION.

F DAILY/SHIFT/PHASE/PERIODIC: INCLUDES ALL UNITS OF

WORK ACCOMPLISHED DURING DAILY/SHIFT/ PHASED/

PERIODIC INSPECTIONS. THIS CODE WILL BE USED ON BOTH

THE "LOOK" PHASE OF THE INSPECTION AND ON ALL "FIX"

PHASE DOCUMENTS GENERATED FOR CORRECTION OF

DEFICIENCIES NOTED DURING THE INSPECTION.

G TRANSPORT: INCLUDES ALL UNITS OF WORK PERFORMED

BY ACTIVITIES IN RECORDING AIRCRAFT AND EQUIPMENT

TRANSPORTABILITY (TO BE USED WITH ACTION CODE

"Q"). THIS CODE SHOULD BE USED IN CONJUNCTION WITH

THE TEARDOWN AND BUILD-UP OF EQUIPMENT BEING

TRANSPORTED BY AIR, LAND AND SEA.

H EMERGENCY ON-SITE REPAIR: INCLUDES ALL UNITS OF

WORK AUTHORIZED AND ACCOMPLISHED AS A RESULT OF

AN EMERGENCY REQUEST FOR ASSISTANCE. APPLICABLE

TO ALL LEVELS OF MAINTENANCE PERFORMED BY 38 EIG

AND INSTALLATION TEAMS AND ORGANIZATIONAL AND

INTERMEDIATE MAINTENANCE PERFORMED BY AFMC MOBILE

MAINTENANCE TEAMS. EXCLUDES ACCOMPLISHMENT OF

TCTOs.

J SCHEDULED CALIBRATION OF EQUIPMENT OR COMPONENTS:

INCLUDES ALL UNITS OF WORK ACCOMPLISHED

CONCURRENTLY WITH A SCHEDULED CALIBRATION.

Q FORWARD-SUPPORT SPARES: INCLUDES ALL UNITS OF WORK

PERFORMED BY ALL ACTIVITIES IN RECORDING IN-SHOP

MAINTENANCE ACTIONS ON AFMC FORWARD-SUPPORT

SPARES, EXCLUDING ACCOMPLISHMENT OF TCTOs.

R DEPOT MAINTENANCE: INCLUDES ALL UNITS OF WORK

ACCOMPLISHED WHEN DEPOT MAINTENANCE OR

REHABILITATION IS PERFORMED, REGARDLESS OF LOCATION

INCLUDES EMERGENCY ON-SITE REPAIR. EXCLUDES

ACCOMPLISHMENT OF TCTOs.

III-001

TYPE MAINTENANCE CODES

CODE DEFINITION

S SPECIAL INSPECTION: INCLUDES ALL UNITS OF WORK

ACCOMPLISHED DURING ALL PHASES OF SPECIAL

INSPECTIONS. EXCLUDING ACCOMPLISHMENT OF TCTOs.

T TIME-COMPLIANCE TECHNICAL ORDER: INCLUDES

ACCOMPLISHMENT OF ALL TCTOs AND STATUS REPORTING.

III-002

ACTION TAKEN CODES

CODE DEFINITION

0 BENCH CHECKED -- NRTS WARRANTY ITEM: REPAIR NOT

AUTHORIZED, ITEM UNDER WARRANTY.

1 BENCH CHECKED -- NRTS (NOT REPARABLE THIS STATION)

-- REPAIR NOT AUTHORIZED -- SHOP IS NOT AUTHORIZED

TO ACCOMPLISH THE REPAIR. THIS CODE SHALL ONLY BE

USED WHEN IT IS SPECIFICALLY PROHIBITED BY CURRENT

TECHNICAL DIRECTIVES. THIS CODE SHALL NOT BE USED

DUE TO LACK OF AUTHORITY FOR EQUIPMENT, TOOLS,

FACILITIES SKILLS, PARTS, OR TECHNICAL DATA.

2 TEST/INSPECT -- NRTS -- LACK OF EQUIPMENT, TOOLS,

SKILLS, OR FACILITIES -- REPAIR AUTHORIZED BUT CANNOT

BE ACCOMPLISHED DUE TO LACK OF EQUIPMENT, TOOLS OR

FACILITIES. THIS CODE SHALL BE USED WITHOUT REGARD

AS TO WHETHER THE EQUIPMENT, TOOLS, OR FACILITIES

ARE AUTHORIZED OR UNAUTHORIZED. MAY BE USED FOR

ON-EQUIPMENT WHEN AN END ITEM ID IS RETURNED TO

DEPOT.

3 BENCH CHECKED -- NRTS -- DUE TO LEAN LOGISTICS POLICY.

REPAIR COULD NOT BE ACCOMPLISHED DUE TO PARTS

NON-AVAILABILITY WITHIN THE TIME LIMIT IMPOSED BY LEAN

LOGISTICS POLICY.

4 BENCH CHECKED -- NRTS -- LACK OF PARTS -- PARTS ARE

NOT AVAILABLE TO ACCOMPLISH REPAIR.

5 BENCH CHECKED -- NRTS -- SHOP BACKLOG -- REPAIR

CANNOT BE ACCOMPLISHED DUE TO EXCESSIVE SHOP

BACKLOG.

6 BENCH CHECKED -- NRTS -- LACK OF TECHNICAL DATA

-- REPAIR CANNOT BE ACCOMPLISHED DUE TO LACK OF

MAINTENANCE MANUALS, DRAWINGS, ETC., WHICH DESCRIBE

DETAILED REPAIR PROCEDURES AND REQUIREMENTS.

7 BENCH CHECKED -- NRTS -- LACK OF EQUIPMENT, TOOLS,

FACILITIES, SKILLS, PARTS OR TECHNICAL DATA -- REPAIR

AUTHORIZED BUT CANNOT BE ACCOMPLISHED DUE TO

LACK OF AUTHORIZATION TO OBTAIN OR POSSES REQUIRED

EQUIPMENT, TOOLS, FACILITIES, SKILLS, PARTS, OR

TECHNICAL DATA.

IV-001

CODE DEFINITION

8 BENCH CHECKED -- RETURN TO DEPOTS -- RETURNED TO

DEPOTS BY DIRECTION OF SYSTEM MANAGER (SM) OR

ITEM MANAGER (IM). USE ONLY WHEN ITEMS THAT ARE

AUTHORIZED FOR BASE-LEVEL REPAIR ARE DIRECTED TO BE

RETURNED TO DEPOT FACILITIES BY SPECIFIC WRITTEN OR

VERBAL COMMUNICATION FROM THE IM OR SM, OR WHEN

ITEMS ARE TO BE RETURNED TO DEPOT FACILITIES FOR

MODIFICATION IN ACCORDANCE WITH A TIME-COMPLIANCE

TECHNICAL ORDER (TCTO), OR AS MDR EXHIBITS.

9 BENCH CHECKED -- CONDEMNED -- ITEM CANNOT BE

REPAIRED AND IS TO BE PROCESSED FOR CONDEMNATION,

RECLAMATION OR SALVAGE. THIS CODE WILL ALSO BE USED

WHEN A "CONDEMNED" CONDITION IS DISCOVERED DURING

FIELD MAINTENANCE DISASSEMBLY OR REPAIR.

A BENCH CHECKED AND REPAIRED -- BENCH CHECK AND

REPAIR OF ANY ONE ITEM IS ACCOMPLISHED AT THE SAME

TIME (FOR ON-EQUIPMENT ONLY) (ALSO SEE CODE F).

B BENCH CHECKED -- SERVICEABLE (FOR OFF-EQUIPMENT

WORK ONLY) -- ITEM IS BENCH CHECKED AND NO REPAIR IS

REQUIRED. THIS CODE WILL BE USED WHEN IT IS DEFINITELY

DETERMINED THAT THE DISCREPANCY DOES NOT EXIST

OR CANNOT BE REPLICATED. MUST BE USED WITH HOW

MALFUNCTION CODE 672, 799, 812, OR 948. BENCH CHECK

SERVICEABLE (BCS) IS THE TERMINOLOGY FOR BASE-LEVEL

ACTION TAKEN CODE B AND RETEST OKAY (RTOK) IS THE

TERMINOLOGY FOR DEPOT-LEVEL ACTION TAKEN CODE B.

C BENCH CHECKED-REPAIR DEFERRED -- BENCH CHECK IS

ACCOMPLISHED AND REPAIR ACTION IS DEFERRED (SEE

CODE F).

D BENCH CHECKED-TRANSFERRED TO ANOTHER BASE OR

UNIT -- ITEM IS BENCH CHECKED AT A FORWARD OPERATING

BASE, DISPERSED OPERATING BASE, OR ENROUTE BASE

AND IS FOUND BASE FOR REPAIR. NOT USED FOR ITEMS

RETURNED TO DEPOT FOR OVERHAUL. USED ALSO FOR PME

OR OTHER EQUIPMENT SENT TO ANOTHER BASE/UNIT FOR

BENCH CHECK, CALIBRATION, OR REPAIR TO BE RETURNED

AND FOR ITEM FORWARDED TO CONTRACTORS ON BASE

LEVEL JOBS.

E INITIAL INSTALLATION -- FOR INSTALLATION ACTIONS NOT

RELATED TO A PREVIOUS REMOVAL ACTION SUCH AS

INSTALLATION OF ADDITIONAL EQUIPMENT OR INSTALLATION

OF AN ITEM TO REMEDY A SHIP-SHORT CONDITION. MUST

USE WITH HOW MAL CODE 799.

IV-002

CODE DEFINITION

F REPAIR -- NOT TO BE USED TO CODE "ON-EQUIPMENT"

WORK IF ANOTHER CODE WILL APPLY. WHEN IT IS USED

IN SHOP ENVIRONMENT, THIS CODE WILL DENOTE REPAIR

AS A SEPARATE UNIT OF WORK AFTER A BENCH CHECK.

SHOP REPAIR INCLUDES THE TOTAL REPAIR MAN-HOURS

AND INCLUDES CLEANING, DISASSEMBLY, INSPECTION,

ADJUSTMENT, REASSEMBLY AND LUBRICATION OF MINOR

COMPONENTS INCIDENT TO THE REPAIR WHEN THESE

SERVICES ARE PERFORMED BY THE SAME WORKCENTER.

FOR PRECISION MEASUREMENT EQUIPMENT, THIS CODE

WILL BE USED ONLY WHEN CALIBRATION OF REPAIRED ITEM

IS REQUIRED (SEE CODE G).

G REPAIRS AND/OR REPLACEMENT OF MINOR PARTS,

HARDWARE, AND SOFTGOODS (SEALS, GASKETS,

ELECTRICAL CONNECTORS, FITTINGS, TUBING, HOSE,

WIRING, FASTENERS, VIBRATION ISOLATORS, BRACKETS,

ETC.) -- WORK UNIT CODES DO NOT COVER MOST

NON-REPAIRABLE ITEMS; THEREFORE, WHEN ITEMS SUCH

AS THOSE IDENTIFIED ABOVE ARE REPAIRED OR REPLACED,

THIS ACTION TAKEN CODE WILL BE USED. WHEN THIS ACTION

TAKEN CODE IS USED, THE WORK UNIT CODE WILL IDENTIFY

THE ASSEMBLY BEING DIRECTLY RELATED TO PARTS BEING

REPAIRED.

H EQUIPMENT CHECKED -- NO REPAIR REQUIRED -- (FOR

"ON-EQUIPMENT" WORK ONLY) ALL DISCREPANCIES WHICH

ARE CHECKED AND FOUND TO REQUIRE NO FURTHER

MAINTENANCE ACTION. THIS CODE WILL BE USED ONLY

IF IT IS DEFINITELY DETERMINED THAT A REPORTED

DEFICIENCY DOES NOT EXIST OR CANNOT BE DUPLICATED.

MUST BE USED WITH HOW MAL CODE 672, 799, 812 OR 948.

CANNOT DUPLICATE (CND) IS THE TERMINOLOGY FOR ALL

ON-EQUIPMENT ACTION TAKEN CODE H MAINTENANCE

ACTIONS.

J CALIBRATED -- NO ADJUSTMENT REQUIRED -- USE

THIS CODE WHEN AN ITEM IS CALIBRATED AND FOUND

SERVICEABLE WITHOUT NEED FOR ADJUSTMENT, OR IS

FOUND TO BE IN TOLERANCE BUT IS ADJUSTED MERELY TO

PEAK OR MAXIMIZE THE READING. IF THE ITEM REQUIRES

ADJUSTMENT TO ACTUALLY MEET CALIBRATION STANDARDS

OR TO BRING IN TOLERANCE, USE CODE K.

K CALIBRATED -- ADJUSTMENT REQUIRED -- ITEM MUST BE

ADJUSTED TO BRING IT IN TOLERANCE ORMEET CALIBRATION

STANDARDS. IF THE ITEM WAS REPAIRED OR NEEDS REPAIR

IN ADDITION TO CALIBRATION AND ADJUSTMENT, USE CODE F.

IV-003

CODE DEFINITION

L ADJUST -- INCLUDES ADJUSTMENTS NECESSARY FOR

SAFETY AND PROPER FUNCTIONING OF EQUIPMENT SUCH AS

ADJUST, BLEED, BALANCE, RIG, FIT, REROUTE, SEAT/RESEAT,

POSITION/REPOSITION, PROGRAM/REPROGRAM, OR

ACTUATING RESET BUTTON, SWITCH OR CIRCUIT BREAKER.

FOR USE WHEN A DISCREPANCY OR CONDITION IS

CORRECTED BY THESE TYPESOF ACTIONS. IF THE IDENTIFIED

COMPONENT OR ASSEMBLY ALSO REQUIRES REPLACEMENT

OF BITS AND PIECES AS WELL AS ADJUSTMENT, ENTER THE

APPROPRIATE REPAIR ACTION TAKEN CODE INSTEAD OF L.

M DISASSEMBLE --DISASSEMBLY ACTIONWHEN THE COMPLETE

MAINTENANCE JOB IS BROKEN INTO PARTS AND REPORTED

AS SUCH. DO NOT USE FOR ON-EQUIPMENT WORK.

N ASSEMBLE -- ASSEMBLY ACTION WHEN THE COMPLETE

MAINTENANCE JOB IS BROKEN INTO PARTS AND REPORTED

AS SUCH. DO NOT USE FOR ON-EQUIPMENT WORK.

P REMOVED -- ITEM IS REMOVED AND ONLY THE REMOVAL

IS TO BE ACCOUNTED FOR. THIS INSTANCE DELAYED OR

ADDITIONAL ACTIONS WILL BE ACCOUNTED FOR SEPARATELY

(SEE CODES Q, R, S, T, AND U).

Q INSTALLED -- ITEM IS INSTALLED AND ONLY THE INSTALLATION

ACTION IS TO BE ACCOUNTED FOR (SEE E, P, R, S, T, AND U)

(THIS CODE APPLIES TO REINSTALLATION/ RELOADING OF

APPLICATION SOFTWARE).

R REMOVE AND REPLACE -- ITEM IS REMOVED AND ANOTHER

LIKE ITEM IS INSTALLED (SEE CODES T AND U) AND REMOVAL

AND/OR REPLACEMENT OF SUBASSEMBLIES FROM THEIR

NEXT HIGHER ASSEMBLY.

S REMOVE AND REINSTALL -- ITEM IS REMOVED AND THE SAME

ITEM REINSTALLED (SEE CODES T AND U). MUST BE USED

WITH HOW MAL CODE 800, 804 OR 805. NOT FOR SERIALLY

TRACKED OR TCI, SEE PARAGRAPH 7-4.

T REMOVED FOR CANNIBALIZATION -- A COMPONENT IS

CANNIBALIZED. THE WORK UNIT CODE WILL IDENTIFY THE

COMPONENT BEING CANNIBALIZED. MUST BE USED WITH

HOW MALFUNCTION CODE 799 OR 875.

U REPLACED AFTER CANNIBALIZATION -- THIS CODE

WILL BE ENTERED WHEN A COMPONENT IS REPLACED

AFTER CANNIBALIZATION. MUST BE USED WITH HOW

MALFUNCTIONED CODE 799 OR 875.

IV-004

CODE DEFINITION

V CLEAN -- CLEANING IS ACCOMPLISHED TO CORRECT

DISCREPANCY AND/OR CLEANING IS NOT ACCOUNTED

FOR AS PART OF A REPAIR ACTION SUCH AS CODE F.

INCLUDES WASHING, ACID BATH, BUFFING, SAND BLASTING,

DEGREASING, DECONTAMINATION, ETC. CLEANING AND

WASHING OF COMPLETE ITEMS SUCH AS GROUND

EQUIPMENT VEHICLES, MISSILES, OR AIRPLANES SHOULD BE

RECORDED BY UTILIZING SUPPORT GENERAL CODES.

X TEST-INSPECTION-SERVICE -- ITEM IS TESTED OR INSPECTED

OR SERVICED (OTHER THAN BENCH CHECK) AND NO REPAIR

IS REQUIRED. THIS CODE DOES NOT INCLUDE SERVICING OR

USED WHEN DOCUMENTING TIME AGAINST A REPORTED

DISCREPANCY IDENTIFYING A TEST, INSPECT OR SERVICE

TOWARD A WUC ITEM FOR ON- AND OFF-EQUIPMENT

MAINTENANCE THAT IS UNRELATED TO A CND ACTION. WILL

BE USED WHEN A REPORTED DISCREPANCY IDENTIFYING A

DEFICIENCY TOWARD A WORK UNIT CODE ITEM IS IDENTIFIED

TO BE "WITHIN LIMITS", WITH THE APPROPRIATE NO DEFECT

HOW MALFUNCTION CODE. WILL BE USED TO DOCUMENT

OPERATIONAL CHECKS PERFORMED SEPARATELY AFTER A

MAINTENANCE ACTION IN THE SAME JOB CONTROL NUMBER

THAT IS UNRELATED TO A CND ACTION. WILL BE USED WHEN

TESTING ITEMS RECEIVED FROM SUPPLY.

Y TROUBLESHOOT -- TIME EXPENDED IN LOCATING A

DISCREPANCY IS GREAT ENOUGH TO WARRANT SEPARATING

THE TROUBLESHOOT TIME FROM THE REPAIR TIME. USE OF

THIS CODE NECESSITATES COMPLETION OF TWO SEPARATE

LINE ENTRIES, OR TWO SEPARATE FORMS, ONE FOR THE

TROUBLESHOOT PHASE AND ONE FOR THE REPAIR PHASE.

WHEN RECORDING THE TROUBLESHOOT TIME SEPARATE

FROM THE REPAIR TIME, THE TOTAL TIME TAKEN TO ISOLATE

THE PRIMARY CAUSE OF THE DISCREPANCY SHOULD BE

RECORDED UTILIZING THE WORK UNIT CODE OF THE

DEFECTIVE ITEM OR ASSEMBLY. IF THE DISCREPANCY WAS

NOT ISOLATED, THE SUBSYSTEM OR SYSTEM WORK UNIT

CODE SHOULD BE USED.

Z CORROSION TREATMENT -- INCLUDES CLEANING, TREATING,

PRIMING, AND PAINTING OF CORRODED OR REPAIRED

COMPONENTS AND DETERIORATED COATINGS. THIS CODE

SHOULD ALWAYS BE USED WHEN ACTUALLY TREATING

CORRODED ITEMS OR THOSE WITH DETERIORATED PAINT.

THE ITEM THAT IS CORRODED OR HAS DAMAGED PAINT

WILL BE IDENTIFIED BY THE WORK UNIT CODE (ALSO SEE

SUPPORT GENERAL CODE 09000).

IV-005/(IV-006 blank)

WHEN DISCOVERED CODES

CODE DEFINITION

4 CORROSION CONTROL INSPECTION.

C DURING EQUIPMENT OPERATION/CAUSED EQUIPMENT DOWN

TIME.

D DURING EQUIPMENT OPERATION/DID NOT CAUSE EQUIPMENT

DOWN TIME.

H SCHEDULED INSPECTION CEM PHASE OR PERIODIC (DOES

NOT INCLUDE DAILY/SHIFT).

J DAILY INSPECTION/SHIFT VERIFICATION.

P FUNCTIONAL/OPERATIONAL/SYSTEMS CHECK.

Q SPECIAL INSPECTION.

R QUALITY CONTROL CHECK.

S DEPOT LEVEL MAINTENANCE.

T DURING SCHEDULED CALIBRATION.

V DURING UNSCHEDULED CALIBRATION.

W DISASSEMBLY FOR MAINTENANCE.

Y UPON RECEIPT OR WITHDRAWAL FROM SUPPLY STOCKS.

Z DURING INITIAL EQUIPMENT INSTALLATION.

V-001/(V-002 blank)

HOW MALFUNCTIONED CODES

APLHABETICAL LISTING

CODE DEFINITION

AVIONICS/ELECTRICAL/COMPUTER

127 ADJUSTMENT OR ALIGNMENT IMPROPER

652 ALIGN TIME EXCESSIVE

627 ATTENUATION INCORRECT

045 BATTERY REPLACED, NO OTHER FAULT

674 BIT FAULT INDICATED WRONG UNIT

673 BIT FAULT INDICATOR FAILURE

675 BIT FAULT NOT DUPLICATED, PARAMETERS CONFIRMED BY

DATA

070 BROKEN

672 BUILT IN TEST (BIT) FALSE ALARM

644 BUILT-IN TEST (BIT) INDICATED FAULT

080 BURNED OUT OR DEFECTIVE LAMP, METER OR INDICATING

DEVICE

969 CANNOT RESONATE INPUT CAVITY

025 CAPACITANCE INCORRECT

956 COMPUTER EQUIPMENT MALFUNCTION

949 COMPUTER MEMORY ERROR/DEFECT

028 CONDUCTANCE INCORRECT

029 CURRENT INCORRECT

311 DAMAGED OR DEFECTIVE COMPONENT (BULB, TRANSISTOR,

INTEGRATED CIRCUIT, FUSE, ETC.)

943 DATA ERROR

312 DEGRADED SYSTEM PERFORMANCE

974 DOES NOT TRACK TUNING CURVE

309 ELECTRICAL MEASUREMENTS INCORRECT

866 EXPIRATION OF MAXIMUM TIME, (TO DIRECTED)

602 FAILED OR DAMAGED DUE TO MALFUNCTION OF ASSOCIATED

EQUIPMENT

VI-001

APLHABETICAL LISTING

CODE DEFINITION

AVIONICS/ELECTRICAL/COMPUTER

242 FAILED TO OPERATE - SPECIFIC REASON UNKNOWN

290 FAILS DIAGNOSTIC/AUTOMATIC TEST

959 FAILS TO TRANSFER TO REDUNDANT EQUIPMENT

051 FAILS TO TUNE OR DRIFTS

940 FAILURE OF APPLICATION SOFTWARE

698 FAULTY CARD, TAPE, PROGRAM, OR DISK

001 FAULTY TUBE, TRANSISTOR, OR INTEGRATED CIRCUIT

037 FLUCTUATES, UNSTABLE, OR ERRATIC

991 FREQUENCY OUT OF BAND, UNSTABLE, OR INCORRECT

982 FROZEN TUNING MECHANISM

472 FUSE BLOWN OR DEFECTIVE CIRCUIT PANEL/BREAKER

065 HIGH VOLTAGE OR STANDING WAVE RATIO

942 ILLEGAL OPERATION OR ADDRESS

816 IMPEDANCE INCORRECT

308 IMPROPER OPERATION

721 IMPROPER RESPONSE TO ELECTRICAL INPUT

718 IMPROPER RESPONSE TO MECHANICAL INPUT

088 INCORRECT GAIN

064 INCORRECT MODULATION

255 INCORRECT OUTPUT

626 INDUCTANCE INCORRECT

987 INPUT/OUTPUT PULSE DISTORTION

350 INSULATION BREAKDOWN

901 INTERMITTENT

678 INTERNAL SELF-PROTECTION CIRCUIT ACTIVATED

383 LOCK ON MALFUNCTION

VI-002

APLHABETICAL LISTING

CODE DEFINITION

AVIONICS/ELECTRICAL/COMPUTER

962 LOW POWER (ELECTRICAL)

957 NO DISPLAY

254 NO OUTPUT

607 NO-GO INDICATION

941 NON-PROGRAMMED HALT

876 NON-TECHNICAL ORDER DIRECTED REMOVAL/REMOVAL FOR

RECONFIGURATION

450 OPEN

457 OSCILLATING

609 OUT OF TRACK/FAILS TO TRACK

964 POOR SPECTRUM

875 REMOVAL FOR OR REPLACEMENT AFTER (CANNIBALIZATION)

870 REMOVAL FOR RESEARCH, TEST, OR DIAGNOSTIC EVENT

878 REMOVAL TO PERFORM SCHEDULED/SPECIAL INSPECTION

(PE, HSI, ETC., - TO-DIRECTED)

567 RESISTANCE INCORRECT

583 SCOPE PRESENTATION INCORRECT OR FAULTY

635 SENSITIVITY INCORRECT

615 SHORTED

649 SWEEP MALFUNCTION

695 SYNC ABSENT OR INCORRECT

752 TAPE MISSING/DEFECTIVE

911 TCTO NOT COMPLIED WITH, TCTO COMPLIED WITH IN ERROR,

OR PLACED IN WORK IN ERROR

580 TEMPERATURE SENSITIVE

877 TO-IDENTIFIED COMPONENTS

637 TRIGGERING INCORRECT

VI-003

APLHABETICAL LISTING

CODE DEFINITION

AVIONICS/ELECTRICAL/COMPUTER

561 UNABLE TO ADJUST TO LIMITS

939 UNABLE TO LOAD PROGRAM

944 UPDATE OR VERIFICATION OF PROGRAM/SOFTWARE LOAD

692 VIDEO FAULTY

691 VIDEO OUT OF FOCUS

169 VOLTAGE INCORRECT

694 WEAK VIDEO

VI-004

APLHABETICAL LISTING

CODE DEFINITION

PHYSICAL/MECHANICAL

651 AIR IN SYSTEM

710 BEARING FAILURE OR FAULTY

780 BENT, BUCKLED, COLLAPSED, DENTED, DISTORTED, OR

TWISTED

135 BINDING, STUCK, OR JAMMED

070 BROKEN

900 BURNED OR OVERHEATED

111 BURST OR RUPTURED

006 CONTACTS, CONNECTORS OR CONNECTIONS DEFECTIVE

170 CORRODED MILD/MODERATE

667 CORRODED SEVERE

190 CRACKED

020 CUT, WORN, CHAFFED, FRAYED, OR TORN

972 DAMAGED PROBE

865 DETERIORATED (FOR PROTECTIVE COATING/SEALING

DEFECTIVE; USE WITH ACTION TAKEN CODE Z.)

230 DIRTY, CONTAMINATED, OR SATURATED BY FOREIGN

MATERIAL

932 DOES NOT ENGAGE, LOCK, OR UNLOCK CORRECTLY

553 DOES NOT MEET SPECIFICATIONS, DRAWING, OR OTHER

CONFORMANCE REQUIREMENTS (USE WITH "WHEN

DISCOVERED" CODE Y)

305 EQUIPMENT OR MATERIAL PHYSICALLY DAMAGED

306 EQUIPMENT OR MATERIAL PHYSICALLY FAILED

690 EXCESSIVE VIBRATION OR ROUGH OPERATION

632 EXPENDED (THERMAL BATTERY, FIRE EXTINGUISHER, ETC.)

602 FAILED OR DAMAGED DUE TO MALFUNCTION OF ASSOCIATED

EQUIPMENT

086 IMPROPER HANDLING, SHIPPING OR MAINTENANCE DAMAGE

VII-001

APLHABETICAL LISTING

CODE DEFINITION

PHYSICAL/MECHANICAL

159 INTERNAL REDUCTION GEAR FAILURE

410 LACK OF, OR IMPROPER LUBRICATION

884 LEAD BROKEN

381 LEAKING INTERNAL OR EXTERNAL

890 LIGHTNING STRIKE DAMAGE

730 LOOSE

105 LOOSE, DAMAGED, OR MISSING HARDWARE (NUTS, BOLTS,

SCREWS, CLAMPS, SAFETY-WIRE, ETC.)

750 MISSING

008 NOISY/CHATTERING

200 OIL LEAKAGE

948 OPERATOR ERROR

458 OUT OF BALANCE

192 OVER TEMPERATURE

425 PITTED, NICKED, CHIPPED, SCORED, SCRATCHED, OR CRAZED

525 PRESSURE INCORRECT/FLUCTUATES

002 SERVICING (MAY BE USED WITH WUC ITEMS)

585 SHEARED

874 STORAGE DAMAGE OR DETERIORATION

315 SURGES/FLUCTUATES

334 TEMPERATURE LIMITS EXCEEDED

167 TENSION OR TORQUE INCORRECT

599 TRAVEL OR EXTENSION INCORRECT

622 WET/CONDENSATION

VII-002

APLHABETICAL LISTING

CODE DEFINITION

NO DEFECT

799 NO DEFECT

800 NO DEFECT - COMPONENT REMOVED/REINSTALLED TO

FACILITATE OTHER MAINTENANCE (INCLUDES DISCONNECT/

CONNECTION OF ELECTRICAL WIRES, HYDRAULIC LINES,

ETC.).

788 NO DEFECT - FAILURE CAUSED BY IMPROPER TURN ON

SEQUENCE.

812 NO DEFECT - INDICATED DEFECT CAUSED BY ASSOCIATED

EQUIPMENT MALFUNCTION.

813 NO DEFECT - INDICATED DEFECT CAUSED BY ASSOCIATED

SOFTWARE/KEY CODE FAILURE.

677 NO DEFECT - UNKNOWN SYSTEM LIMITATION.

802 NO DEFECT - PARTIAL TCTO COMPLIANCE.

804 NO DEFECT - REMOVED FOR SCHEDULED MAINTENANCE,

MODIFICATION OR RELIABILITY ASSESSMENT.

798 NO DEFECT - TCTO COMPLIED WITH BY RECORD CHECK OR

INSPECTION. NO MODIFICATION REQUIRED.

801 NO DEFECT - TCTO COMPLIED WITH, ALL APPLICABLE

OPERATIONS COMPLETED.

793 NO DEFECT - TCTO KIT RECEIVED BY BASE SUPPLY OR PARTS

ARE AVAILABLE IN SUPPLY.

796 NO DEFECT - TCTO NOT APPLICABLE: THIS IS AN ERROR

CODE USED TO TELL THE IM/SM THAT THIS SPECIFIC PIECE OF

EQUIPMENT SHOULD NOT HAVE BEEN INCLUDED IN THE TCTO.

THIS CODE IS NOT TO BE USED TO REPORT COMPLIANCE.

797 NO DEFECT - TCTO PREVIOUSLY COMPLIED WITH.

921 NO DEFECT - ITEM HAS BEEN REBUILT, REFURBISHED,

BEEN REPLACED (CONSUMABLE ITEM) OR HAS HAD PARTS

REPLACED BECAUSE OF TECHNICAL ORDER (TIME CHANGE)

REQUIREMENTS (TO BE USED WITH ACTION TAKEN REPAIR

CODE G, OR R, P, AND Q FOR TIME CHANGE).

VIII-001/(VIII-002 blank)

NUMERICAL LISTING

CODE DEFINITION

AVIONICS/ELECTRICAL/COMPUTER

001 FAULTY TUBE, TRANSISTOR, OR INTEGRATED CIRCUIT

025 CAPACITANCE INCORRECT

028 CONDUCTANCE INCORRECT

029 CURRENT INCORRECT

037 FLUCTUATES, UNSTABLE, OR ERRATIC

045 BATTERY REPLACED, NO OTHER FAULT

051 FAILS TO TUNE OR DRIFTS

064 INCORRECT MODULATION

065 HIGH VOLTAGE OR STANDING WAVE RATIO

070 BROKEN

080 BURNED OUT OR DEFECTIVE LAMP, METER OR INDICATING

DEVICE

088 INCORRECT GAIN

127 ADJUSTMENT OR ALIGNMENT IMPROPER

169 VOLTAGE INCORRECT

242 FAILED TO OPERATE - SPECIFIC REASON UNKNOWN.

254 NO OUTPUT

255 INCORRECT OUTPUT

290 FAILS DIAGNOSTIC/AUTOMATIC TEST

308 IMPROPER OPERATION

309 ELECTRICAL MEASUREMENTS INCORRECT

311 DAMAGED OR DEFECTIVE COMPONENT (BULB, TRANSISTOR,

INTEGRATED CIRCUIT, FUSE, ETC.)

312 DEGRADED SYSTEM PERFORMANCE

350 INSULATION BREAKDOWN

383 LOCK ON MALFUNCTION

450 OPEN

IX-001

NUMERICAL LISTING

CODE DEFINITION

AVIONICS/ELECTRICAL/COMPUTER

457 OSCILLATING

472 FUSE BLOWN OR DEFECTIVE CIRCUIT PANEL/BREAKER

561 UNABLE TO ADJUST TO LIMITS

567 RESISTANCE INCORRECT

580 TEMPERATURE SENSITIVE

583 SCOPE PRESENTATION INCORRECT OR FAULTY

602 FAILED OR DAMAGED DUE TO MALFUNCTION OF ASSOCIATED

EQUIPMENT

607 NO-GO INDICATION

609 OUT OF TRACK/FAILS TO TRACK

615 SHORTED

626 INDUCTANCE INCORRECT

627 ATTENUATION INCORRECT

635 SENSITIVITY INCORRECT

637 TRIGGERING INCORRECT

644 BUILT-IN TEST (BIT) INDICATED FAULT

649 SWEEP MALFUNCTION

652 ALIGN TIME EXCESSIVE

672 BUILT IN TEST (BIT) FALSE ALARM

673 BIT FAULT INDICATOR FAILURE

674 BIT FAULT INDICATED WRONG UNIT

675 BIT FAULT NOT DUPLICATED, PARAMETERS CONFIRMED BY

DATA

678 INTERNAL SELF-PROTECTION CIRCUIT ACTIVATED

691 VIDEO OUT OF FOCUS

692 VIDEO FAULTY

694 WEAK VIDEO

IX-002

NUMERICAL LISTING

CODE DEFINITION

AVIONICS/ELECTRICAL/COMPUTER

695 SYNC ABSENT OR INCORRECT

698 FAULTY CARD, TAPE, PROGRAM, OR DISK

718 IMPROPER RESPONSE TO MECHANICAL INPUT

721 IMPROPER RESPONSE TO ELECTRICAL INPUT

752 TAPE MISSING/DEFECTIVE

816 IMPEDANCE INCORRECT

866 EXPIRATION OF MAXIMUM TIME, (TO DIRECTED)

870 REMOVAL FOR RESEARCH, TEST, OR DIAGNOSTIC EVENT

875 REMOVAL FOR OR REPLACEMENT AFTER (CANNIBALIZATION)

876 NON-TECHNICAL ORDER DIRECTED REMOVAL/REMOVAL FOR

RECONFIGURATION

877 TO-IDENTIFIED COMPONENTS

878 REMOVAL TO PERFORM SCHEDULED/SPECIAL INSPECTION

(PE, HSI, ETC., - TO-DIRECTED)

901 INTERMITTENT

911 TCTO NOT COMPLIED WITH, TCTO COMPLIED WITH IN ERROR,

OR PLACED IN WORK IN ERROR

939 UNABLE TO LOAD PROGRAM

940 FAILURE OF APPLICATION SOFTWARE

941 NON-PROGRAMMED HALT

942 ILLEGAL OPERATION OR ADDRESS

943 DATA ERROR

944 UPDATE OR VERIFICATION OF PROGRAM/SOFTWARE LOAD

949 COMPUTER MEMORY ERROR/DEFECT

956 COMPUTER EQUIPMENT MALFUNCTION

957 NO DISPLAY

959 FAILS TO TRANSFER TO REDUNDANT EQUIPMENT

IX-003

NUMERICAL LISTING

CODE DEFINITION

AVIONICS/ELECTRICAL/COMPUTER

962 LOW POWER (ELECTRICAL)

964 POOR SPECTRUM

969 CANNOT RESONATE INPUT CAVITY

974 DOES NOT TRACK TUNING CURVE

982 FROZEN TUNING MECHANISM

987 INPUT/OUTPUT PULSE DISTORTION

991 FREQUENCY OUT OF BAND, UNSTABLE, OR INCORRECT

IX-004

NUMERICAL LISTING

CODE DEFINITION

PHYSICAL/MECHANICAL

002 SERVICING (MAY BE USED WITH WUC ITEMS)

006 CONTACTS, CONNECTORS OR CONNECTIONS DEFECTIVE

008 NOISY/CHATTERING

020 CUT, WORN, CHAFFED, FRAYED, OR TORN

070 BROKEN

086 IMPROPER HANDLING, SHIPPING OR MAINTENANCE DAMAGE

105 LOOSE, DAMAGED, OR MISSING HARDWARE (NUTS, BOLTS,

SCREWS, CLAMPS, SAFETY-WIRE, ETC.)

111 BURST OR RUPTURED

135 BINDING, STUCK, OR JAMMED

159 INTERNAL REDUCTION GEAR FAILURE

167 TENSION OR TORQUE INCORRECT

170 CORRODED MILD/MODERATE

190 CRACKED

192 OVER TEMPERATURE

200 OIL LEAKAGE

230 DIRTY, CONTAMINATED, OR SATURATED BY FOREIGN

MATERIAL

305 EQUIPMENT OR MATERIAL PHYSICALLY DAMAGED

306 EQUIPMENT OR MATERIAL PHYSICALLY FAILED

315 SURGES/FLUCTUATES

334 TEMPERATURE LIMITS EXCEEDED

381 LEAKING INTERNAL OR EXTERNAL

410 LACK OF, OR IMPROPER LUBRICATION

425 PITTED, NICKED, CHIPPED, SCORED, SCRATCHED, OR CRAZED

458 OUT OF BALANCE

525 PRESSURE INCORRECT/FLUCTUATES

X-001

NUMERICAL LISTING

CODE DEFINITION

PHYSICAL/MECHANICAL

553 DOES NOT MEET SPECIFICATIONS, DRAWING, OR OTHER

CONFORMANCE REQUIREMENTS. (USE WITH "WHEN

DISCOVERED" CODE Y)

585 SHEARED

599 TRAVEL OR EXTENSION INCORRECT

602 FAILED OR DAMAGED DUE TO MALFUNCTION OF ASSOCIATED

EQUIPMENT

622 WET/CONDENSATION

632 EXPENDED (THERMAL BATTERY, FIRE EXTINGUISHER, ETC.)

651 AIR IN SYSTEM

667 CORRODED SEVERE

690 EXCESSIVE VIBRATION OR ROUGH OPERATION

710 BEARING FAILURE OR FAULTY

730 LOOSE

750 MISSING

780 BENT, BUCKLED, COLLAPSED, DENTED, DISTORTED, OR

TWISTED

865 DETERIORATED (FOR PROTECTIVE COATING/SEALING

DEFECTIVE; USE WITH ACTION TAKEN CODE Z.)

874 STORAGE DAMAGE OR DETERIORATION

884 LEAD BROKEN

890 LIGHTNING STRIKE DAMAGE

900 BURNED OR OVERHEATED

932 DOES NOT ENGAGE, LOCK, OR UNLOCK CORRECTLY.

948 OPERATOR ERROR

972 DAMAGED PROBE

X-002

NUMERICAL LISTING

CODE DEFINITION

NO DEFECT

677 NO DEFECT - UNKNOWN SYSTEM LIMITATION.

788 NO DEFECT - FAILURE CAUSED BY IMPROPER TURN ON

SEQUENCE.

793 NO DEFECT - TCTO KIT RECEIVED BY BASE SUPPLY OR PARTS

ARE AVAILABLE IN SUPPLY.

796 NO DEFECT - TCTO NOT APPLICABLE: THIS IS AN ERROR

CODE USED TO TELL THE IM/SM THAT THIS SPECIFIC PIECE OF

EQUIPMENT SHOULD NOT HAVE BEEN INCLUDED IN THE TCTO.

THIS CODE IS NOT TO BE USED TO REPORT COMPLIANCE.

797 NO DEFECT - TCTO PREVIOUSLY COMPLIED WITH.

798 NO DEFECT - TCTO COMPLIED WITH BY RECORD CHECK OR

INSPECTION. NO MODIFICATION REQUIRED.

799 NO DEFECT

800 NO DEFECT - COMPONENT REMOVED/REINSTALLED TO

FACILITATE OTHER MAINTENANCE (INCLUDES DISCONNECT/

CONNECTION OF ELECTRICAL WIRES, HYDRAULIC LINES,

ETC.).

801 NO DEFECT - TCTO COMPLIED WITH, ALL APPLICABLE

OPERATIONS COMPLETED.

802 NO DEFECT - PARTIAL TCTO COMPLIANCE.

804 NO DEFECT - REMOVED FOR SCHEDULED MAINTENANCE,

MODIFICATION OR RELIABILITY ASSESSMENT.

812 NO DEFECT - INDICATED DEFECT CAUSED BY ASSOCIATED

EQUIPMENT MALFUNCTION.

813 NO DEFECT - INDICATED DEFECT CAUSED BY ASSOCIATED

SOFTWARE/KEY CODE FAILURE.

921 NO DEFECT - ITEM HAS BEEN REBUILT, REFURBISHED,

BEEN REPLACED (CONSUMABLE ITEM) OR HAS HAD PARTS

REPLACED BECAUSE OF TECHNICAL ORDER (TIME CHANGE)

REQUIREMENTS (TO BE USED WITH ACTION TAKEN REPAIR

CODE G, OR R, P, AND Q FOR TIME CHANGE).

XI-001/(XI-002 blank)

WORK

UNIT UNIQUE DATA CODES FOR MCS

CODE (MAINTENANCE COST SYSTEM)

ALT00 Alert Duty. All man-hours expended while waiting for alert aerospace vehicles to takeoff or land, such as strategic, defense,tactical, standing by for crash alert, or for alert missile when no work is being accomplished. Not to be used for standby, awaiting work assignments, lag or other delays, or when direct productive effort is being expended.

CMP00 Compensatory Time For Overtime. All direct assigned man-hours excused from normal duty as a result of previously expended overtime man-hours.

DTL00 Detail, Squadron or Base Duties. Manhours expended by direct labor personnel (labor code 100) performing on-base duties such as charge of quarters, policing, building maintenance, driver, dining hall, parade, commanders call, general military training, nontechnical training, etc.

LVE00 Leave. Man-hours excused from duty, pass or official, military, medical, or sick leave.

TRN00 Maintenance Training. Man-hours expended in on-the-job training, formal and informal maintenance technical training.

NOTE

These codes are to be used to account for man-hour expenditures of personnel with an assigned "direct" labor code when performing one of the above functions. Documentation guidance for AFTO form 349 entries is contained in 00-20-2-series technical orders.

XII-001/(XII-002 blank)

UNIT SUPPORT GENERAL CODES

CODE (EXCEPT 03000 AND 04000)

NOTE

Support general codes are for recording production credit of repetitive tasks of a general nature, and are not used for recording malfunctions, repair, not repairable this station (NRTS), or condemnation actions. The multitude of tasks, which must be accomplished, preclude listing the all in this table. This is not intended to restrict documentation of tasks. All support general work must be identified to the most appropriate code.

System program managers, majcoms, and local commands may add additional lower level codes to 01000, 02000, 05000, 06000, 07000, and 09000 to track specific actions under the category definition. However, data transmitted up channel is rolled up to the two-digit level. Categories 03000 and 04000 will remain standardized as listed in this appendix. Note that some codes have more than one definition. HQ AFMC/ENB is OPR for these codes.

01000 GROUND HANDLING, SERVICING, AND RELATED TASKS

Ground Handling

Equipment Moving or Repositioning

Installation/Relocation of Equipment

Removal of Equipment

Mission Equipment Operation or Support When Not Associated With Scheduled or Unscheduled Maintenance

Servicing And Related Tasks

Scheduled Power Changeover

Troubleshooting End Items Or Facilities (use only for end items or facilities that do not have a WUC assigned)

Unscheduled Power Changeover

Power Production Service and Checkout

Environmental Control

Rehabilitation of Antenna Systems

Unscheduled Antenna System Service

Clearing of Antenna/Transmission Right-of-Way

Installation of New Antenna System

01-001

UNIT SUPPORT GENERAL CODES

CODE (EXCEPT 03000 AND 04000)

Receiver or Transmitter Frequency Changes

Tape Development, Reproduction and Analysis

Telephone Number Change

Rehabilitation of Equipment

02000 EQUIPMENT AND FACILITY CLEANING

Washing or Degreasing

Cleaning and Treating Equipment to Prevent Corrosion

Ground Snow, Frost, and Ice Removal

Cleaning Antenna Systems, Mobile Facilities and Fixed Facilities

Decontamination

05000 PRESERVATION, DE-PRESERVATION, AND STORAGE OF

EQUIPMENT

06000 GROUND SAFETY

07000 PREPARATION AND MAINTENANCE OF RECORDS

This Code Will be Used to Record Only the Direct Labor Expended in Preparation/Maintenance of Status and Historical Forms (this excludes initiation and completion of production document forms).

08000 SPECIAL PURPOSE

09000 SHOP SUPPORT GENERAL CODE

Fabricate (Includes fabrication or local manufacture of miscellaneous items).

Stenciling/Painting (includes stenciling, lettering, installing decals, instrument range marking, etc., and painting for cosmetic purposes only). Do Not Use This Code For Treating Corrosion or Painting of Parts/Assemblies/Equipment For Corrosion Prevention/Control.

Testing and Servicing Fire Extinguishers

Reclamation

01-002

UNIT

CODE SUPPORT GENERAL CODES

SCHEDULED INSPECTIONS

03100 AS REQUIRED (OTHER THAN AS SPECIFIED BELOW)

03107 7 DAY INTERVAL

03114 14 DAY INTERVAL

03121 21 DAY INTERVAL

03128 28 DAY INTERVAL

03142 42 DAY INTERVAL

03156 56 DAY INTERVAL

03184 84 DAY INTERVAL

03268 168 DAY INTERVAL

03336 336 DAY INTERVAL

03-001/(03-002 blank)

UNIT

CODE SUPPORT GENERAL CODES

SPECIAL INSPECTIONS

04110 OPERATIONAL OR SYSTEM CHECKS

04111 SPECIAL MODIFICATION INSPECTION

04112 EQUIPMENT INVENTORY

04141 CORROSION CONTROL INSPECTION (USE IF ACCOMPLISHED

SEPARATELY FROM A SCHEDULED INSPECTION)

04-001/(04-002 blank)

UNIT

CODE

MCS/AMCS CENTRAL PROCESSING SYSTEM

CA000 CENTRAL PROCESSING SYSTEM

CAA00 SERVER SUBASSEMBLY, DATA PROCESSING, V880, (2 ea)

OPS XFR SERVER # 1, 3A12A4

OPS XFR SERVER # 2, 3A13A4

CAAA0 SERVER, DATA PROCESSING

CAAC0 INTERFACE UNIT, ADP, PCI BUS/1000 BASE-SX, A2, A3 (2 ea)

CAAD0 INTERFACE UNIT, PCI ADAPTER, QUAD FAST ETHERNET, A14

CAAE0 POWER SUPPLY, PS1, PS2, PS3 (3 ea) CAAF0 ADAPTER, SCSI HOST, PCI DUAL ULTRA320, A1, A15 (2 ea)

CAA99 NOC

CAB00 COMPUTER SYSTEM, DIGITAL, (12 ea)

COSE, 1A1 - 1A12

CABA0 COMPUTER SUBASSEMBLY, DIGITAL, A1

CABAA Disk Drive Unit, DVD-ROM, A1 CABAB Disk Drive Unit, Internal Floppy, A2 CABAC Graphics Accelerator Card, A3, A4 (2 ea) CABAD Disk Drive Unit, A5 CABAE Interface Unit, ADP PCI BUS/1000 BASE-SX, A7 CABAF Interface Unit, ADP, PCI BUS/ULTRA-3 SCSI, A9

CABB0 KEYBOARD INSTRUMENT, ELECTRONICS AND MOUSE, DATA

ENTRY, A2

CABD0 DISPLAY UNIT, A3, A4, A5 (3 ea)

CAB99 NOC

CAC00 COMPUTER SYSTEM, DIGITAL, (3 ea)

NETWORK MANAGER, 1A13

SYSTEM ADMINISTRATION, 3A18

LAB CONTROL, 3A20

CACA0 COMPUTER SUBASSEMBLY, DIGITAL, A1

CACAA Disk Drive Unit, DVD-ROM Drive, A1 CACAB Disk Drive Unit, Internal Floppy, A2 CACAC Graphics Accelerator Card, A3 CACAD Disk Drive Unit, A5 CACAE Interface Unit, ADP PCI BUS/1000 BASE-SX, A7, A8 (2 ea) CACAF Interface Unit, ADP, PCI BUS/ULTRA-3 SCSI, A9

CACB0 KEYBOARD INSTRUMENT, ELECTRONIC & MOUSE, DATA

ENTRY, A2

CACD0 DISPLAY UNIT, A3

CACE0 EXTERNAL CD-RW DRIVE, A6 (1A13 and 3A18 Only)

CAC99 NOC

CA-001

UNIT

CODE

MCS/AMCS CENTRAL PROCESSING SYSTEM

CA000 CENTRAL PROCESSING SYSTEM - Continued CAD00 COMPUTER SYSTEM, DIGITAL, (2 ea)

ARTS, 3A52

ARTS, 3A53

CADA0 COMPUTER SUBASSEMBLY, DIGITAL, A1

CADAA Disk Drive Unit, DVD-ROM Drive, A1 CADAB Disk Drive Unit, Internal Floppy, A2 CADAC Graphics Accelerator Card, A3 CADAD Disk Drive Unit, A5 CADAE Module, PC Time And Frequency, A6 CADAF Interface Unit, ADP PCI BUS/1000 BASE-SX, A7 CADAG Interface Unit, ADP, PCI BUS/ULTRA-3 SCSI, A9

CADB0 KEYBOARD, INSTRUMENT, ELECTRONIC & MOUSE, DATA

ENTRY, A2

CADD0 TRANSCEIVER, F/O, PASSIVE, A5

CADE0 DISPLAY UNIT, A3

CAD99 NOC

CAE00 COMPUTER SYSTEM, DIGITAL, (2 ea)

OPS TRANSFER, 3A54

OPS TRANSFER, 3A55

CAEA0 COMPUTER SUBASSEMBLY, DIGITAL, A1

CAEAA Disk Drive Unit, DVD-ROM Drive, A1 CAEAB Disk Drive Unit, Internal Floppy, A2 CAEAC Graphics Accelerator Card, A3 CAEAD Disk Drive Unit, A5 CAEAE Interface Unit, ADP PCI BUS/1000 BASE-SX, A7 CAEAF Interface Unit, ADP, PCI BUS/ULTRA-3 SCS, A9

CAEB0 KEYBOARD, INSTRUMENT, ELECTRONIC AND MOUSE, DATA

ENTRY, A2

CAED0 DISPLAY UNIT, A3

CAE99 NOC

CAF00 SERVER SUBASSEMBLY, DATA PROCESSING, 280R, (14 ea)

MISSION SERVER #3 AND #4, 3A7A6, 3A7A7

TT&C #1 - #6 SERVER, 3A8A1 - 3A8A6

GATEWAY #1 AND #2 SERVER, 3A9A1, 3A9A2

CRYPTO SERVER #1 AND #2, 3A9A3, 3A9A4

L-BAND #1 AND #2 SERVER, 3A9A5, 3A9A6

CAFA0 SERVER, DATA PROCESSING, (MCS Only) CAFAA Interface Unit, ADP, PCI BUS/ULTRA-3 SCSI, A2 CAFAB Interface Unit, ADP PCI BUS/1000 BASE-SX, A1 CAFAC 4GB Memory (4X 1GB SDRAM DIMMS), A7A1 - A7A4 CAFAE External Floppy Disk (3A9A3, 3A9A4 Only), A11

CA-002

UNIT

CODE

MCS/AMCS CENTRAL PROCESSING SYSTEM

CA000 CENTRAL PROCESSING SYSTEM - Continued CAF00 SERVER SUBASSEMBLY, DATA PROCESSING, 280R, (14 ea)

MISSION SERVER #3 AND #4, 3A7A6, 3A7A7

TT&C #1 - #6 SERVER, 3A8A1 - 3A8A6

GATEWAY #1 AND #2 SERVER, 3A9A1, 3A9A2

CRYPTO SERVER #1 AND #2, 3A9A3, 3A9A4

L-BAND #1 AND #2 SERVER, 3A9A5, 3A9A6 - Continued

CAFB0 SERVER, DATA PROCESSING, [AMCS Only] CAFBA Interface Unit, ADP, PCI BUS/ULTRA-3 SCSI, A2 CAFBB Interface Unit, ADP PCI BUS/1000BASE-SX, A1 CAFBC 2GB Memory (4X 512MB SDRAM DIMMS), A7A1 - A7A4 CAFBD Memory Expansion Kit (4 X 512MB SDRAM DIMMS), A7A5

- A7A8 CAFBF External Floppy Disk (3A9A3, 3A9A4 Only), A11

CAF99 NOC

CAG00 COMPUTER SUBASSEMBLY, CATALYST SWITCH, 2950

3A3A2 3A56A1 [MCS Only]

CAGA0 COMPUTER, DIGITAL DATA TRANSFER CATALYST SWITCH

CAGB0 INTERFACE UNIT, COMMUNICATION EQUIPMENT, 1000

BASE-SX, A1, A2 (2 ea)

CAG99 NOC

CAH00 COMPUTER SUBASSEMBLY, CATALYST SWITCH, 6506, (2 ea)

CATALYST SWITCH # 1, 3A3A3

CATALYST SWITCH # 2, 3A3A4

CAHA0 COMPUTER, DIGITAL DATA TRANSFER CATALYST SWITCH

CAHB0 CIRCUIT CARD ASSY, SUPERVISOR, A1

CAHBA Memory Card, Personal Computer, A1

CAHC0 INTERFACE UNIT, COMMUNICATION EQUIPMENT, GIGABIT

ETHERNET, A2-A4 (3 ea)

CAHD0 POWER SUPPLY, PS1

CAH99 NOC

CAJ00 COMPUTER SUBASSEMBLY, CATALYST SWITCH, 4003, (2 ea)

OPS XFR CATALYST SWITCH # 1, 3A10A3

OPS XFR CATALYST SWITCH # 2, 3A10A4

CAJA0 COMPUTER, DIGITAL DATA XFR, CATALYST SW

CAJB0 CIRCUIT CARD ASSY, GIGABIT ETHERNET, A2, A3 (2 ea) CAJBA Interface Unit, Communication Equipment, 1000 BASE-SX, A1-A6 (6 ea)

CAJ99 NOC

CA-003

UNIT

CODE

MCS/AMCS CENTRAL PROCESSING SYSTEM

CA000 CENTRAL PROCESSING SYSTEM - Continued

CAK00 COMPUTER SYSTEM, DIGITAL

ALMANAC PC, 1A68

CAKA0 COMPUTER SUBASSEMBLY, DIGITAL, A1

CAKAA Disk Drive Unit 48X CD-RW Drive, A1 CAKAB Transport, Magnetic Tape, Internal, A2 CAKAC Disk Drive Unit, Internal Floppy, A3 CAKAD Interface Unit, Communications Equipment, Ethernet, PCI A4

CAKB0 MOUSE, DATA ENTRY, A4

CAKC0 DISPLAY UNIT, A2

CAKD0 KEYBOARD, DATA ENTRY, A3

CAKE0 COMPUTER, DIGITAL

CAK99 NOC

CAL00 SERVER SUBASSEMBLY, DATA PROCESSING, 280R, (6 ea)

MISSION SERVER #1, 3A4A4

MISSION SERVER #2, 3A4A5

COMMON 1 SERVER, 3A6A1

COMMON 2 SERVER, 3A6A2

MISSION SERVER #5, 3A11A3

MISSION SERVER #6, 3A11A4

CALA0 SERVER, DATA PROCESSING [MCS Only] CALAA Interface Unit, ADP, PCI BUS/ULTA320 SCSI, A2, A10 (2 ea) CALAB Interface Unit, ADP PCI BUS/1000 BASE-SX, A1 CALAC 4GB Memory (4X 1GB SDRAM DIMMS), A7A1 - A7A4 (4 ea) CALAD Interface Unit, PCI Adapater, Quad Fast Ethernet, A9 (3A4, 3A11 ONLY)

CALAE Adapter, Dual Gb Enet and Dual SCSI/P, A9 (3A6 ONLY) CALB0 SERVER, DATA PROCESSING [AMCS Only] CALBA Interface Unit, ADP, PCI BUS/ULTRA320 SCSI, A2, A10 CALBB Interface Unit, ADP PCI BUS/1000BASE-SX, A1 CALBC 2GB Memory (4X 512MB SDRAM DIMMS), A7A1 - A7A4 (4 ea) CALBD Memory Expansion Kit (4 X 512MB SDRAM DIMMS), A7A5

- A7A8 (4 ea) CALBE Interface Unit, PCI Adapter, Quad Fast Ethernet, A9 (3A4, 3A11 ONLY)

CALBF Adapter, Dual Gb Enet and Dual SCSI/P, A9 (3A6 ONLY)

CAL99 NOC

CAM00 DATA PROCESSING SERVER V240 ASSY, 3A68A2, 3A68A5

(2 ea)

CAMA0 SERVER, DATA PROCESSING, V240

CAMB0 DISK DRIVE, 73 GB, A1-A4 (4 ea)

CA-004

UNIT

CODE

MCS/AMCS CENTRAL PROCESSING SYSTEM

CA000 CENTRAL PROCESSING SYSTEM - Continued

CAM00 DATA PROCESSING SERVER V240 ASSY, 3A68A2, 3A68A5

(2 ea) - Continued

CAMC0 DVD ROM INTERNAL, A5

CAMD0 POWER SUPPLY, 400-WAT 2U, A6, A7 (2 ea)

CAME0 ADAPTER, SCSI HOST, PCI DUAL ULTRA 320, A8

CAMF0 CARD, GRAPHICS ACCELERATOR, A9

CAMG0 INTERFACE Unit, PCI-X 4 GB FC HBA, A10

CAM99 NOC

CAN00 COMPUTER SUBASSY, SB2500 W/S (NWO), 1A33, 1A34 (2 ea)

CANA0 SB2500 WORKSTATION, A1

CANAA Hard Drive,146 GB, A1 CANAB Graphics Accelerator Card, A2, A5 (2 ea)

CANB0 KEYBOARD, INSTRUMENT, ELECTRONIC & MOUSE, DATA

ENTRY, A2

CANC0 DISPLAY UNIT, A3, A4, A5 (3 ea)

CAND0 DUAL PORT SERVER ADAPTER, 1000BASE-SX, A1A4

CAN99 NOC

CAP00 MOW/TAT2 SYSTEM EQUIPMENT

CAPA0 MOW AND TAT2 WORKSTATION ASSEMBLY, 1A70, 1A71 (2 ea)

CAPB0 KEYBOARD, INSTRUMENT, ELECTRONIC & MOUSE, DATA

ENTRY

CAPC0 22" WIDE SCREEN FLATPANEL MONITOR, 1A75

CAP99 NOC

CA-005/(CA-006 blank)

UNIT

CODE

MCS/AMCS INPUT/OUTPUT CONTROL SYSTEM

CF000 INPUT/OUTPUT CONTROL SYSTEM

CFA00 VME, RED, ALTERED, (3 ea)

RED VME-A, 3A37A4

RED VME-B, 3A37A5

RED VME-B, 3A37A511 [AMCS ONLY]

RED VME-C, 3A38A3 [MCS ONLY]

CFAA0 VME, RED

CFAB0 CARD, PROCESSOR, DOWNLINK, A1

CFAE0 CARD, IRIG, A4

CFAF0 CARD, PROCESSOR, UPLINK, A5

CFA99 NOC

CFB00 VME, BLACK ARTS, ALTERED, (3 ea)

BLACK ARTS VME-A, 3A41A4

BLACK ARTS VME-B, 3A41A5

BLACK ARTS VME-C, 3A41A11 (AMCS ONLY)

BLACK ARTS VME-C, 3A42A1 [MCS ONLY]

CFBA0 VME, CHASSIS

CFBB0 CARD, PROCESSOR, DOWNLINK, A1

CFBD0 CARD, PROCESSOR UPLINK, A5

CFB99 NOC

CFC00 SWITCHING SET SUBASSEMBLY, COMMUNICATION, 7513,

(2 ea)

COMMUNICATIONS ROUTER # 1, 3A29A1

COMMUNICATIONS ROUTER # 2, 3A29A2

CFCA0 SWITCHING SET, COMMUNICATIONS

CFCC0 CCA, VERSATILE INTERFACE PROCESSOR A3-A5, A12 (4 ea) CFCCA Interface Unit, Communication Equipment Serial, A1 CFCD0 CCA, GIGABIT ETHERNET PROCESSOR, A6, A13 (2 ea) CFCDA Interface Unit, Communication Equipment, 1000 BASE-SX, A1 CFCDB Microcircuit, Memory, SDRAM, A2

CFCE0 CCA, ROUTE SWITCH PROCESSOR, A7

CFCEA Route Switch Processor CFCEB Memory Card, Personal Computer, A1 CFCEC Microcircuit, Memory, DRAM, A2

CFCF0 CCA, VERSATILE INTERFACE PROCESSOR, A9

CFCFA Interface Unit, Communication Equipment, Serial, A1 CFCFB Interface Unit, Communication Equipment, 100 BASE-FX, A2

CFCG0 CCA, VERSATILE INTERFACE PROCESSOR, A11

CFCGA Interface Unit, Communications Equipment, 100 BASE-FX, A1 CFCGB Interface Unit, Communications Equipment, 100 BASE-TX, A2

CF-001

UNIT

CODE

MCS/AMCS INPUT/OUTPUT CONTROL SYSTEM

CF000 INPUT/OUTPUT CONTROL SYSTEM - Continued

CFC00 SWITCHING SET SUBASSEMBLY, COMMUNICATION, 7513,

(2 ea)

COMMUNICATIONS ROUTER # 1, 3A29A1

COMMUNICATIONS ROUTER # 2, 3A29A2 - Continued

CFCH0 POWER SUPPLY PS1, PS2 (2 ea) CFCJ0 CCA VERSATILE INTERFACE PROCESSOR, A2, A10 (2 ea) CFCJA Interface Unit, Communications Equipment, Serial, A1 CFCJB Interface Unit, Communication Eqpt, 100Base-TX, A2

CFCK0 CCA VERSATILE INTERFACE PROCESSOR, A1

CFCKA Interface Unit, Communication Equipment 100Base-TX, A1, A2 (2 ea)

CFC99 NOC

CFD00 SWITCH SUBASSEMBLY, FIBER OPTIC, 3A4A1

CFDA0 SWITCH, FIBER OPTIC

CFDB0 CONNECTOR, RCPT, FIBER OPTIC, MULTIMODE LC, A1-A12,

A18-A32 [MCS ONLY] (27 ea)

CFDC0 CONNECTOR, RCPT, FIBER OPTIC, MULTIMODE LC, A1-A32

[AMCS ONLY] (32 ea)

CFDD0 CONNECTOR, RCPT, FIBER OPTIC, MULTIMODE LC, A13 -

A17 [MCS ONLY] (5 ea)

CFD99 NOC

CFE00 SWITCH SUBASSEMBLY, ELECTRIC, SERIAL ASCII, 3A4A2

CFEA0 SWITCH, ELECTRICAL, SERIAL ASCII

CFEB0 INTERFACE UNIT, ADP, SERIAL, A1-A6 (6 ea)

CFE99 NOC

CFF00 SWITCH, ELECTRONIC, (COMMON SCSI), 3A7A1

CFF99 NOC

CFG00 SWITCHING SET SUBASSEMBLY, COMMUNICATION, 7204,

(2 ea)

OPS XFR ROUTER # 1, 3A10A1

OPS XFR ROUTER # 2, 3A10A2

CFGA0 SWITCHING SET, COMMUNICATION

CFGB0 INTERFACE UNIT, COMMUNICATION EQUIPMENT, SERIAL, A2

CFGC0 CIRCUIT CARD ASSEMBLY, NETWORK PROCESSOR, A4

CFGD0 CIRCUIT CARD ASSEMBLY, GIGABIT ETHERNET, A1

CFGDA Interface Unit, Communication Equipment, 1000 BASE SX, A1

CF-002

UNIT

CODE

MCS/AMCS INPUT/OUTPUT CONTROL SYSTEM

CF000 INPUT/OUTPUT CONTROL SYSTEM - Continued

CFG00 SWITCHING SET SUBASSEMBLY, COMMUNICATION, 7204,

(2 ea)

OPS XFR ROUTER # 1, 3A10A1

OPS XFR ROUTER # 2, 3A10A2 - Continued

CFGE0 CIRCUIT CARD ASSEMBLY, I/O CONTROLLER, A3

CFG99 NOC

CFM00 MEDIA CONVERTER

CFMA0 TRANSCEIVER, FIBER OPTIC, PASSIVE (10 ea)

3A37A9-A10

3A37A12 [AMCS ONLY]

3A38A8 [MCS ONLY]

3A41A9-A10

3A41A12 [AMCS ONLY]

3A42A6 [MCS ONLY]

3A52A5, 3A53A5

CFMB0 MEDIA CONVERTER (2 ea)

3A56A10-A11 [MCS ONLY]

CFMC0 MEDIA CONVERSION MODULE

3A56A7A1 [MCS ONLY]

CFMD0 CONVERTER, SIGNAL DATA (8 ea)

1A23 [MCS ONLY]

3A56A6 3A65A14

3A65A13 [MCS ONLY]

3A65A17, A19 [AMCS ONLY]

3A67A16, A17 [AMCS ONLY]

CFME0 FIBER MEDIA CONVERTER (2 ea) 3A68A8A1-A8A2

CFM99 NOC

CFN00 ROUTER ASSEMBLY, MODEL 2621, 3A67A11, 3A67A12,

3A67A14 (3 ea) [AMCS ONLY]

CFNA0 ROUTER 2621

CFNB0 MICROCIRCUIT, MEMORY, SDRAM, A1

CFNC0 MICROCIRCUIT, MEMORY, INTERNAL FLASH, A2

CFN99 NOC

CFL00 SWITCHING SET COMMUNICATION, 2950, 3A67A13 [AMCS

ONLY]

CFL99 NOC

CF-003/(CF-004 blank)

UNIT

CODE

MCS/AMCS INPUT/OUTPUT SYSTEM

CL000 INPUT/OUTPUT SYSTEM

CLA00 PRINTER ASSY, LASERJET, 2200DN, (7 Total) 1A15-1A19, 3A24 [MCS ONLY] (6 ea)

1A18 [AMCS ONLY]

CLAA0 PRINTER, AUTO DATA PROCESSING

CLAB0 MICROCIRCUIT, MEMORY, SDRAM, A1

CLA99 NOC

CLB00 PRINTER ASSEMBLY, 4050N, 1A15-1A17 [AMCS ONLY] (3 ea)

CLBA0 PRINTER, AUTO DATA PROCESSING, A1

CLBB0 ADAPTER, TOKEN RING, A2

CLB99 NOC

CLC00 PRINTER ASSY, LASERJET 9000DN

1A20 [MCS ONLY]

1A69 [AMCS ONLY]

CLCA0 PRINTER, AUTO DATA PROCESSING

CLCB0 MICROCIRCUIT, MEMORY SDRAM, A1

CLC99 NOC

CLD00 TERMINAL, DATA PROCESSOR, 3A25-3A28 (3 ea)

CLD99 NOC

CLE00 PRINTER ASSY, 530DN, 1A22 [MCS Only]

CLE99 NOC

CLF00 PRINTER, LASERJET, 1A73

CLF99 NOC

CL-001/(CL-002 blank)

UNIT

CODE

MCS/AMCS AUXILARY STORAGE SYSTEM

CQ000 AUXILARY STORAGE SYSTEM

CQA00 TRANSPORT, MAGNETIC TAPE, EXT

1A14 3A19

CQA99 NOC

CQB00 MEMORY UNIT SUBASSY, DATA STORAGE, (17 ea)

MISSION 1 RAID 1, 3A5A3

MISSION 1 RAID 2, 3A5A4

MISSION 2 RAID 1, 3A5A5

MISSION 2 RAID 2, 3A5A6

COMMON 1 RAID 1, 3A6A3

COMMON 1 RAID 2, 3A6A4

COMMON 2 RAID 1, 3A6A5

COMMON 2 RAID 2, 3A6A6

MISSION 5 RAID 1, 3A11A5

MISSION 5 RAID 2, 3A11A6

MISSION 6 RAID 1, 3A11A7

MISSION 6 RAID 2, 3A11A8

OPS XFR 1 RAID 1, 3A12A2

OPS XFR 1 RAID 2, 3A12A3

OPS XFR 2 RAID 1, 3A13A2

OPS XFR 2 RAID 2, 3A13A3

LAB CONTROL, 3A21

CQBA0 MEMORY UNIT, DATA STORAGE, RACKMOUNTED, [Except 3A21]

CQBB0 MEMORY UNIT, DATA STORAGE, DESKTOP, 3A21

CQBC0 HARD DRIVE, 36.4 GB INTERNAL, A1-A11 (11 ea) (A1-A12 (12

ea) (3A21 ONLY))

CQBD0 ENVIRONMENTAL SERVICES MODULE (ESM), A13

CQBE0 FAN MODULE, (2 ea) CQBF0 POWER SUPPLY, PS1, PS2 (2 ea)

CQB99 NOC

CQC00 TRANSPORT SUBASSEMBLY, MAGNETIC TAPE LIBRARY (2 ea)

8MM COMMON # 1 TAPE LIBRARY, 3A7A2

8MM COMMON # 2 TAPE LIBRARY, 3A7A3

CQCA0 TRANSPORT, MAGNETIC TAPE LIBRARY, 8mm CQCB0 TRANSPORT, MAGNETIC TAPE, INTERNAL, A1, A2 (2 ea)

CQC99 NOC

CQD00 TRANSPORT,…