Appendix_H_-_Baseline_Calibration_Limit_(BCL)_Listing.docx

PRECISION MEASUREMENT EQUIPMENT LABORATORY (PMEL)

PWS

FAXXXX-1X-D-0111

APPENDIX H – BASELINE CALIBRATION LIMIT (BCL) LISTING

1.0 Andersen BCL

2.0 Andrews BCL

3.0 Arnold BCL

4.0 Barksdale BCL

5.0 Beale BCL

6.0 Cannon BCL

7.0 Cape Canaveral BCL

8.0 Columbus BCL

9.0 Dover BCL

10.0 Dyess BCL

11.0 Eielson BCL

12.0 Ellsworth BCL

13.0 Elmendorf BCL

14.0 FE Warren BCL

15.0 Fairchild BCL

16.0 Feltwell BCL

17.0 Grand Forks BCL

18.0 Hill BCL

19.0 MacDill BCL

20.0 Malmstrom BCL

21.0 Maxwell BCL

22.0 McConnell BCL

23.0 Minot BCL

24.0 Moody BCL

25.0 Offutt BCL

26.0 Patrick BCL

27.0 Peterson BCL

28.0 Robins BCL

29.0 Scott BCL

30.0 Sheppard BCL

31.0 Thule BCL

32.0 Tinker BCL

33.0 Vance BCL

34.0 Vandenberg BCL

35.0 Whiteman BCL

36.0 Wright-Patterson BCL

PMEL PWS

H – 2 image1.emf

Baseline Calibration Listing_Andersen.xls K1_K2_K3_K4_K8 joe.hennessy@hubersuhner.com PMEL ANDERSEN AFB GUAM f041655

Baseline Calibration Listing K1, K3, K4, K8

ITEMS IN RED HAVE BEEN CHANGED OR ADDED

P/N NOMENCLATURE ID# LIMITATION EXCHANGE STANDARDS PREVIOUS IDs

K1

067-0508-00 CALIBRATION FIXTURE A222885 ALL RANGES CAL'D +/- 0.5%

CBU

260-6XLPM VOM SSA260-6XLP A222994 INDICATION ONLY. DO NOT USE FOR QUANTITATIVE MEASUREMENTS; NPC

5A RANGE CAL'D TO +/- 4 % FS. Cal'd in Horizontal Position Only (TO Directed).

3100A-4006 POWER SUPPLY A220978 MONITOR ALL OUTPUTS SOURCE ONLY

3400A VOLTMETER RMS SSA H60-3400A A221292 NOT CAL'D BELOW 50 HZ A222999

1mv Range not Cal'd (CBU).

400EL AC VOLTMETER A223000 3mV TO 300V 10 HZ TO 40 HZ CAL'D TO +/-(3%F.S. + 2.5% OF RDG)

40 HZ TO 2 MHZ CAL'D TO +/-(2.5% F.S.) PREVIOUS

Removed limitation made CBU 1/21/9 jlp

415B PWR SUPPLY A223020 MONITOR ALL OUTPUTS; LABEL REACCOMPLISHED 95129 (NPC)

432BH05 PWR METER A222847 NOISE NOT CAL'D

6111A PWR SUPPLY A223026 MONITOR ALL OUTPUTS (NPC)

AFTO 350 Broken Meter Bracket

6205B DUAL POWER SUPPLY SSA 6205C A223075 MONITOR ALL OUTPUTS (NPC)

77AN MULTIMETER A223196 AC/DC 10 AMP RANGE NOT CAL'D10A AC/DC NOT CAL'D

32 Momn range not cal'd

77AN MULTIMETER A223198 10 AMP RANGE NOT CAL'D

77AN MULTIMETER A223266 Not Cal'd Above 1.9 M Ohms

NPC

80E VOLTAGE DIVIDER C451963 T.O. DIRECTED ACCURACY +/- .025%; FRONT PANEL METER INOPERATIVE S/N 00852

FRONT PANEL METER REPAIRED

80E VOLTAGE DIVIDER A794014 TO Directed. Accuracy +/- 0.025% up to rated voltage; Front panel meter not certified; Use with a differential voltmeter; Model 80E-10 SN 264 12/17/08 jlp

80F-15 VOLTAGE DIVIDER F041357 DCV CAL'D ONLY. CAL'D TO +/- .4%; CBU

80K-40 HIGH VOLTAGE PROBE E182882 ACCURACY +/- .2% (TO DIRECTED) DC ONLY

* +/- 1%, 20 to 35 KVDC at 20 to 30 degrees C add 1% at 10 degrees C to < 20 & > 30 to 45 degrees C; +/- 2%, 0 to < 20 & > 35 to 40 KVDC. DC Cal'd Only. Use w/10 Mohm Input Voltmeter

801A DC GEN-DETECTOR A222899 3uV RANGE NOT CAL'D (PREVIOUS)

845AR NULL DETECTOR A222902 1uV AND 3uV RANGES NOT CAL'D

1uV Range not Cal'd.

893A AC DIFFERENTIAL VOLTMETER A223101 1000 VAC RANGE NOT CAL'D BELOW 50 HZ

CBU

9 SING-MULTI RANGE DC METERS A222990 50 AMP RANGE NOT CAL'D (PREVIOUS); CBU

GPC-3030D Power supply J287862 Monitor all Outputs NPC 9/4/08

HSR203 SR ANGLE IND A224429 NOT CAL'D FOR REFERENCE INPUTS BELOW 26 VOLTS (CBU)

MD1 TS INSULATION BREAKDOWN A223023 VOLTMETER CAL'D TO +/- 3.5%FS, VOLTS OUTPUT

NOT CAL'D ABOVE 14KVDC AMPS METER CAL'D

TO 200uA ONLY, DC OUTPUT POWER NOT CAL'; CALLED DC OPERATION; CBU

VOLTMETER CAL'D TO 14KVDC ONLY TO 3.5% F.S. AMP METER NOT CAL'D DC INPUT POWER (DC OPERATION) NOT CAL'D (PREVIOUS)

ESH25 ELECTROSTATIC VOLTMETER A223010 DC Volts Cal'd Only

MV823B-S1 MILLIVOLTMETER RF A223012 1 mV range not cal'd. NOT CAL'D ABOVE 400 MHZ. >10 MHZ TO 150 MHZ +/- ( 3% of Rdg + 1% FS)

TO DIRECTED

PR28 HI VOLTAGE PROBE B194298 DC CAL'D ONLY

WGMC8-40 432BOPT009 PWR MTR 2EA A221011 NOISE NOT CAL'D. USE ONLY WITH 10' CABLE. P/O WGMC8-40

NOISE NOT CAL'D. USE ONLY WITH 10' CABLE. P/O WGMC8-40; CBU

WGMC8-40 432BOPT009 PWR MTR 2EA A221012 NOISE NOT CAL'D. USE ONLY WITH 10' CABLE. P/O WGMC8-40

NOISE NOT CAL'D. USE ONLY WITH 10' CABLE. P/O WGMC8-40;CBU

152-90-9904 CU Substitution Box A495293 25 CU = 25.25 CU. 300 CU = 298.5 CU. TO Directed

TS-183-B/U Battery Tester A223040 CBU

E3634A Power Supply DC J287495 Monitor all outputs. NPC 8/25/08

E3634A DC Power Supply A223023 Monitor All Outputs. NPC

801C Generator/Detector B112008 1 uV Range Not Calibrated

16345A CALIRATION BOX A220744 Unit designated CBU. drj 5/5/08

K2

240C POWER RESISTOR A222943 Monitor All Outputs (NPC)

K3

1062.5502.11 SIGNAL GENERATOR E225109 SMY Residual AM is certified to <0.03% (TO directed) Infor Timebase Factor SPCL 51 set to 1727, P/O CIVS with FMAV E225108

SMY Residual AM is certified to <0.03% (TO Directed); SSB Phase Noise, Incidental AM, Not Cal'd. P/O CIVS

11801C SAMPLING OSCILLOSCOPE MAINF C983357 CHANNEL 1 and 2 cald only

205AG SIG GEN AUDIO A223153 MONITOR ALL OUTPUTS/ NPC

240C COMMON RATIO BRIDGE A222900 TO Directed Info for Temp Coefficients

2465A OSCILLOSCOPE A904258 CH3 & CH4 Vertical Bandwidth Cal'd w/o X 10 Attenuator Probe (TO Directed)

278 PROGRAMMABLE FUNCTION GEN A224230 MONITOR ALL OUTPUTS; NPC

284 PULSE GENERATOR F041646 CBU

3011 Feedthru Termination B111683 Range; DC to 1 GHz. VSWR<= 1.25 VSWR only cal'd at male connector end only;verifyDC inpedance prior to use; P/N 3011 S/N 111683

3011 Feedthru Termination B111684 Range; DC to 1 GHz. VSWR <= 1.25 VSWR ONLY CAL'D AT MALE CONNECTTOR END ONLY. Verify Dc impedance prior to use; P/N 3011 s/ 111684

3011 Feedthru Termination B111685 Range; DC to 1 GHz. VSWR <= 1.25 VSWR ONLY CAL'D AT MALE CONNECTTOR END ONLY. Verify Dc impedance prior to use; P/N 3011 s/ 111683

3048MS 8663A-003 SYNTH SIGNAL A495459 PULSE FUNCTION NOT CAL'D, ATTEN NOT CAL'D BELOW -100db, SSB PHASE NOISE FOR REAR PANEL 640 MHz

OUTPUT CAL'D TO -150dbc @ OFFSETS > OR "=" 100khZ

640 MHz output not cal'd (TO Directed). Incidental AM, SSB Phase Noise, SSB Broadband & Noise Floor, Spectral Purity, & Non-Harmonics Not Cal'd. Monitor Pulse Function; Absolute level calibration not cal'd below-120dbm

3048MS 8662A-003 SYNTH SIGNAL A495458 RF ATTEN NOT CAL'D BELOW -110dBm; SSB PHASE NOISE & INCIDENTAL AM NOT CAL'D; SPURIOUS SIGNALS NOT CAL'D

640 MHz output not Cal'd (TO Directed). (Other limitations removed)

Absolute level calibration not cal'd below 100dbm

3048MS 11848AOPT201 PHASE NOISE I A495461 REAR TRACKING GENERATOR INPUT NOT CAL'D

3048MS 8671BOPTH19 SYN CW GEN C764153 HARMONICS CALIBRATED UP TO THE 2ND HARMONIC OF 9GHZ (T.O. DIRECTED) P/O 3048MS; ICO

3310A FUNCTION GEN A222848 MONITOR ALL OUTPUTS (NPC)

3312A FUNCTION GEN A222849 MONITOR ALL OUTPUTS (NPC)

3320B FREQ SYNTHESIZER A223054 MONITOR ALL OUTPUTS; NPC

3325A SYNTHESIZER FUNCTION GEN A482929 Monitor DC Offset and DC Function(previous) High Amp Option 002 Not Cal'd

3335A SYNTHESIZER LEVEL GEN A482128 50 OHM ATTENUATOR 10 DB +/- .031DB; 20 DB +/- .041DB; 40DB +/- .061DB; 60DB +/- .08DB; 70DB +/- .091DB;80DB +/- .101DB;90DB +/- .121DB

750 OHM FLATNESS NOT CAL'D

40db +/- .061db, 60db +/- .08db, 70db +/- .091db, 80db +/- .101db, 90db +/- .121db

3336COPT004-005 SYNTHESIZER LEVEL GEN A494097 PHASE NOT CAL'D

334A DISTORTION ANALYZER A222814 AM DETECTOR NOT CAL'D (T.O. DIRECTED)

Distortion measurement of AM carriers with the TI RF Det selected T.O. Directed

334A DISTORTION ANALYZER A223264 AM DETECTOR NOT CAL'D (T.O. DIRECTED)

Distortion measurement of AM carriers with the TI RF Det selected T.O. Directed

334A DISTORTION ANALYZER A480380 .1% DISTORTION/300uV METER RANGE NOT CAL'D (PREVIOUS) AM DETECTOR NOT CAL'D (T.O. DIRECTED)

AM DETECTOR NOT CALIBRATED: DISTORITION MEASUREMENT OF AM RF CARRIERS WITH TI RF DET SELECTED/CBU.

3586C SELECTIVE LEVEL METER A223981 AMPLITUDE ACCURACY 50 AND 75 OHM INPUTS CAL'D TO +/- .03db FROM

20KHZ TO 32.5MHZ ON THE -80 TO +20dbm RANGE/ CBU

3585B Spectrum Analyzer A495463 Intermodulation Distortion Cal's to -75 dBc; P/O 3048MS

479S6 SIG GEN VOR/ILS C983995 9960 hz dist. Not cal'd; 1300 hz mb not cal'd; 113.7 MHz not cal'd

527E Frequency Difference Meter A222103 Range 10 parts to 11th cannot be verified due to excessive noise (TO Directed)

5345A FREQUENCY COUNTER F041564 LEVEL PRESET NOT CAL'D

652A T/OSCILLATOR A222815 Freq cald to +/- 3.5% expand mode ref @ 1Khz Atten cald to +/- .5db below -30db

Attenuator accuracy at -40DB +/-.081 and -50DB +/- .091 TO Directed/CBU

652A T/OSCILLATOR A223314 DISTORTION CAL'D TO +/- 2% FROM 10 TO 1KhZ. ATTENUATOR CAL'D TO +/-.5 DB BELOW -40DB FLATNESS CAL'D TO +/-3.1%

Attenuator Accuracy: -40 dBm +/- 0.018 dB; -50 dBm +/- 0.091 dB; Expand Mode Ref Frequency 1 kHz (1 X 1 kHz). TO Directed

8447A001 AMPLIFIER DUAL A222837 GAIN +/- .8DB. MONITOR ALL OUTPUTS.

8447F AMPLIFIER A500382 MONITOR ALL OUTPUTS/ NPC

8566A SPECTRUM ANALYZER A241184 NOT CAL'D ABOVE 18GHZ, AVERAGE NOISE LEVEL LESS THAN OR = TO -120 DB FROM 2.39 GHZ TO 5.71 GHZ

Not Cal'd > 18 GHz. Avg Noise </= -120dB from 2.39 GHz to 5.71 GHz. Noise Sidebands; Residual Responses; 2nd Harmonic Distortion; 3rd Order Intermodulation Distortion; Multiple, Image, and Out-Of-Band Responses; Gain Compression; & Line Related Sidebands not Cal'd. (Changes are added as result of new calibration steps in K-pro. (20070625) SJN).

8640BOPT001-002-003 SIG GEN A222817 OUTPUT LEVEL NOT CAL'D BELOW -100db RANGE, PULSE AND SSB NOT CAL'D/cbu

8640BOPT003 SIG GEN A222821 Freq, output level, attenuation and internal ref cald ONLY. output attenuator not cald below -120dbm (PREVIOUS)

Frequency Range, Harmonics, Output Level and Attenuation, Output Level Flatness, & Internal Reference Cal'd Only. Attenuator Not Cal'd Below -120 dBm. (1 Feb 08; SJN)

8640BOPT003 SIG GEN A222824 PULSE, AM AND FM FUNCTIONS NOT CAL'D, SINGLE SIDEBAND PHASE NOISE

NOT CAL'D, OUTPUT ATTEN NOT CAL'D BELOW -100dbM CBU

8660COPT001-003 SIG GEN A222810 CBU

86603A Plug-in C875506 CBU

86633B Mod. Section AM/FM C875895 CBU

8662AOPT043W55 SYNTHESIZED SIGNAL GENERATOR A222142 Incident AM, SSB Ph Noise, SSB Broadband Noise Floor, Spect Purity Non-Harmonics Not Cal'd (Previous) Abs Ampl not cal'd below -100dBm 640 MHz output not cal'd (T.O. Dir)

8662AOPT3 SYNTHESIZER SIG GEN A494903 OUTPUT NOT CAL'D BELOW -119dBm; SSB PHASE NOISE NOT CAL'D; INCIDENTAL AM NOT CAL'D; SEE SPURIOUS SIGNALS LIMITATIONS ON FORM ATTACHED. (PREVIOUS)

8662AOPT003 SYNTHESIZER SIG GEN B110827 640 MHz output Not Cal'd (T.O. Directed). Incidental AM, SSB Phase Noise, SSB Broadband Noise Floor, Spectral Purity Non-Harmonics Not Cal.d (Previous) drj 7/10/08

Cal Interval changed to CBU drj 10-14-08

8662AOPT3 SYNTHESIZER SIG GEN A495458 RF ATTEN NOT CAL'D BELOW-110DBM. SSB PHASE NOISE AND INCIDENTAL (Removed drj 6/3/08)

AM NOT CAL'D. SPURIOUS SIGNALS NOT CAL'D (Removed drj 6/3/08)

640 MHz output not cal'd (TO Directed). Absolute Level Calibration Not Cal'd bel0ow -100 dbm drj 6/3/08

8672A SIG GEN A222813 CBU

f041656

9500B/3200 Oscilloscope Calibrator B111301 Square Wave Voltage Not Cal'd below 5 mVpp (TO Directed). P/O 9500B/3200AF

9530 ACTIVE HEAD, 3.2 GHz B111302 EDGE PULSE(rise and fall times) Not Cal'd. P/O 9500B/3200AF

9530 ACTIVE HEAD, 3.2 GHz B111303 EDGE PULSE(rise and fall times) Not Cal'd. P/O 9500B/3200AF

9530 ACTIVE HEAD, 3.2 GHz B111304 EDGE PULSE(rise and fall times) Not Cal'd. P/O 9500B/3200AF

9530 ACTIVE HEAD, 3.2 GHz B111305 EDGE PULSE(rise and fall times) Not Cal'd. P/O 9500B/3200AF

9550 CALIBRATOR HEAD B111306 P/O 9500B/3200AF. CBU

9560 CALIBRATOR HEAD B111307 CBU

AN/UPM-155 54602A DIGITIZING OS C875648 CH. 4 BW DC - 200MhZ

ANAPM270V3 TRANSPONDER TS A222844 DETECTED VIDEO NOT CAL'D (CBU)

Removed limitation

CG5011 PROGRAMMABLE CAL GEN A494215 CURRENT NOT CAL'D P/O F7529A2TYPEII

E4407B-H50 Spectrum Analyzer J287618 Firmware Revision: A.14.03. No Parameters cal'd above 18 GHz. Info: Timebase set to C:124 F:148. (New item added to inventory, 6 Dec 07. SJN)

H06-5347A MICROWAVE COUNTER/POWER METER C762710 Power Reference Output certified to +/-2% (TO Directed). Not Calibrated above 18 GHz. drj 10-28-08

MRT-HT RUB FREQ STD SSA:MRTH A496723 FRACTION FREQUENCY OUTPUT CAL'D ONLY TO <5 x 10 -11

PM6654COPT9678B-9696 Programmable Counter/Timer C983849 CBU

TTU27E TACHOMETER TEST A223022 CBU

PATECCORE MRT-HT RUBIDIUM A221319 (FFO) cald to > 5 X 10-11

PG502 PULSE GEN 250MHZ C983144 MONITOR ALL OUTPUTS; NPC

PM 1024A FEED THRU TERMINATION B111654 VSWR Only Cal'd, SWR of 1.2 from DC to 500MHz.

PM 1024A FEED THRU TERMINATION B111655 VSWR Only Cal'd, SWR of 1.2 from DC to 500MHz.

PM 3341 Feed thru Termination B111687 Range: DC to 500 MHz Accuracy VSWR<+ 1.2 vswr ONLY CAL'D AT MALE CONNECTOR END ONLY ; VERIFY DC IMPEDANCE PRIOR

PM 3341 FEED THRU TERMINATION B111682 RANGE: DC TO 500 MHZ; VSWR <= 1.2 VSWR ONLY CAL'D AT MALE CONNECTOR END ONLY. VERIFY DC IMPEADANCE PRIOR TO USE

SD24 TDR/SAMPLING HEAD C983359 TDR/TDT Functions Not Cal'd (Output Amplitude and Reflected Risetime.) Info: RT Ch 1 15.6pS, Chan 2 15.6pS P/O F4703A3

P/O F4703A3

SG503 SINE WAVE GEN C875454 FLATNESS +/- 2% FROM 50MHZ TO 100MHZ (T.O. DIRECTED) CAL'D WITH CABLE P/N 012-0482-00 CBU jlp 3/4/09

Absolute Amplitude Not Cal'd Flatness; 2% to 50MHsZ, 3% From 50 to 100MHZ, 5% from 100MHZ to 250MHZ

Flatness +/- 2% from 50 to 100MHz. Cal'd with Cable 012-0057

Flatness Limited to +/- 2% from 50 MHz to 100 MHz Cal'd with Precision Cable P/N 012-0057-01 (T.O. Directed).

SG5030 LVL SINE WAVE GEN A852498 CAL'D WITH LEVELING HEAD, P/N015-2340001SN B010672; FLATNESS CORRECTION 50-100 MHZ

AMPLITUDE FLATNESS AT 75-100MHZ ADD +.8% CORRECTION TO AMPLITUDE REFERENCE LEVEL P/O F7529a2 Type II

Removed red line

Cal'd w/leveling head ID# B010672; P/O F7529A2 Type II

Unit designated CBU drj 5/8/08

Frequency Range, External Counter and internal Reference Cal'd only

015-2350-01 P/O SG5030/A852498 J287487 CBU drj 5/8/08

SG503 SINE WAVE GEN F041656 Flatness +/- 2% from 50 to 100MHz Cal'd with cable 012-057-01 CBU jlp 3/4/09

SG503 SINE WAVE GEN F041663 FLATNESS CAL'D TO +/- 2% FROM 50MHZ TO 100MHZ (T.O. DIRECTED) CAL'D W/ PRECISION CABLE P/N 012-0482-00

SG503 SINE WAVE GEN C875454 FLATNESS CAL'D TO +/- 2% FROM 50MHZ TO 100MHZ, CAL'D WITH CABLE

P/N 012-0482-00 (TO DIRECTED)

SG504 Leveled Sine Wave Generator F041657 Cal'd with Output Head 015-0282-00, S/N 11350 (TO Directed) CBU

TDS410 DIGITIZING OSCILLOSCOPE A494930 PROBE NOT CAL'D/CBU

Probe Comp Not Cal'd (Previous)/CBU

TG501OPT1 TIME MARK GEN C983134 1NS, 2NS RANGES NOT CAL'D

1nS Range not Cal'd

9610A/AF RF REFERENCE SOURCE E225428 Certified to P/N 9640A Specs in 33K3-4-3570-1 (TO Dir) Except Modulation Functions not Cal'd, Atten not cal'd less than -120 dBm and not below -87dBm for 500KHz. Cal'd with Head J288572 P/O 9610A/AF

K4

11583A ATTEN COAXIAL SET A220743 CAL'D 10MHZ TO 18GHZ/ CBU

11583C ATTEN COAXIAL SET B111414 CAL'D FROM DC TO 18 GHZ SERIAL NUMBER 90155

DC to 18 GHz. See Cal Chart in Box. Stated Accuracies are from Charted Values.

11691DOPT001 DIR COUPLER A223996 CBU

11792AH15 SENSOR A495317 REFERENCED TO 3.5 TO N-TYPE ADAPTER, S/N 2407A00683, CAL'D < 18GHZ, SEE CHART , P/O 8902MS

N Type Adapter married to Unit. Not Cal'd above 18 GHz. See Cal Chart. P/O 8902MS

1870A POWER SPLITTER C983239 PHASE TRACKING NOT CAL'D P/N 1870A S/N 2962

1870A POWER SPLITTER C983242 PHASE TRACKING NOT CAL'D P/N 1870A S/N 3105

1870A POWER SPLITTER C983273 PHASE TRACKING NOT CAL'D ABOVE 12 GHZ P/N 1870A S/N 3010

2-10 Attenuator C764647 S/N AE5309. NPC. 24 Jul 1989

2027-3005 COAXIAL DIRECTIONAL COUPLER F022610 Coupling Coefficient 60dB±1dB at 1.075GHz.Coupling Coefficient Variation ±.5dB. Standardized Coupling Coefficient per Freq before each use.

219-3 3db Attenuator B110650 3db +/- 1db

219-3 3db Attenuator B110651 3db +/- 1db

26A-3 3 dB attenuator J288011 Cal'd from DC to 18 gHz only +/ 0.5 dB

26A-10-026 10 dB Attenuator J287571 DC-18 GHz; 10 dB +/- 0.6 dB

New Item added 4 Dec 2007

26A-10-026 10 dB Attenuator J287572 DC-18 GHz; 10 dB +/- 0.6 dB

New Item added 4 Dec 2007

2760 PULSE POWER SOURCE F041230 MONITOR ALL OUTPUTS / CBU

MONITOR ALL OUTPUTS / NPC

28A50-1 PRECISION TERMINATION C764781 SWR<1.02, DC TO 18GHz P/O 8902MS

28N50-2 COAXIAL TERMINATION C954312 SWR ≤ 1.005 +[0.0033 x F(GHz)] DC to ≤4.545 GHz; ≤1.02, >4.545 to 13 GHz; ≤1.03, 13 to

17 GHz; ≤1.02, 17 to 18 GHz

28NF50-2 COAXIAL TERMINATION C954393 SWR ≤ 1.005 +[0.0033 x F(GHz)] DC to 18 GHz.

3004-10 DIR COUPLER COAX A223144 DIRECTIVITY >15DB / CBU

3095 COAXIAL COUPLER A223139 COUPLING ACCURACY +/-1.2db FROM CHARTED VALUES, DIRECTIVITY > 25db SEE AFTO 249 / CBU

3095 COAXIAL COUPLER A223140 SEE CAL CHART

346AOPT01-SP01 Microwave Frequency Counter B111768 Not Cal'd Above 18Ghz, Power Measurement not cal'd.

355DOPT003 VHF ATTENUATOR A221285 CAL'D FROM 10MHZ-50MHZ; 120db position not cald

3551 FIX ATTENUATOR SET A223911 3 dB +/- .3dB, DC to 18 GHz; 6dB Attenuator Removed, 10 dB +/- .5 dB DC to 18 GHz; 20 dB +/- 1dB DC to 18GHz

400594 PISTON POSITION SENSOR J287915 Standardization/Verification required every 6 months IAW Com Data, Operation & Maint. Manual dated 2006; Sensor S/N-7915; P/O PG7601-SYS-AF 11/07/08

4022 DIRECTIONAL POWER SENSOR C954007 See AFPSL CERTIFICATE OF CALIBRATION; CALIBRATED IN FORWARD POWER ONLY; P/O 4421A300; SEE SPEC'S ON BACK OF AFTO 99 TAG; S/N 7602

See AFPSL Certificate of Calibration: 071590018. Model: 4022 S/N: 7602 TO Directed Limitation: Cal'd in FWD power only. Part of 4421A300. Frequency Range: 30 MHz to 1 GHz. Power Range: 0.3 to 1000 Watts. Accuracy: +/- 3.00% of reading. Output Calibrated Only.

4021 DIRECTIONAL POWER SENSOR C954006 See AFPSL CERTIFICATE OF CALIBRATION; CALIBRATED IN FORWARD POWER ONLY; P/O 4421A300; SEE SPEC'S ON BACK OF AFTO 99 TAG; S/N 7540

See AFPSL Certificate of Calibration: 071000066. Model: 4021 S/N: 7540 TO Directed Limitation: Cal'd in FWD power only. Part of 4421A300. Frequency Range: 2 to 30 MHz Power Range: 0.3 to 1000 Watts. Accuracy: +/- 3.00% of reading. Output Calibrated Only.

4227-16 DIRECTIONAL COUPLER C875103 NOT CAL'D ABOVE 18GHZ

NOT CAL'D ABOVE 18GHZ. CBU

432B POWER METER A221011 CBU

435A POWER METER A222792 POWER REF +/-2% (T.O DIRECTED)

436AOPT022 POWER METER A220542 POWER REF CAL'D TO +/-2% (T.O DIRECTED) P/O 436A OPT E41

478A-3 ZIFOR III A583364 SEE AFPSL CERTIFICATE A824973

See AFPSL Cert of Cal. Report (TO Directed Limitation). See Reverse. Model 478A3 S/N 276

5532-26 Sensor Module E225745 No Parameter Cal'd above 18 GHz; Use Type N Adapter S/N 5745 only; P/O MMS 30 Mar 09 jlp

478A H73 THERMISTOR MOUNT See AFPSL Certificate of Calibration Report No. 062980005; Cal'd from 10 to 1090 MHz; Model 478A-H73 S/N 70042. Replaced 6-11-08 drj F057470

A352628 See AFPSL Certificate of Calibration: 081120028 Cal'd from 10 to 1090 MHz, TO Directed Limitation. Model 478-H73 S/N 70075. 6-11-08 drj E204323

478A H63 THERMISTOR MOUNT A495336 SEE CHART PART NUMBER 478A863 S/N 55983; CBU

50-6 Attenuator C764243 P/N 50-6. S/N R7086. NPC. 8 Jun 1993

548ACCN2304W36 MICROWAVE FREQ COUNTER A223061 NOT CAL'D ABOVE 18GHZ, BAND 4 NOT CAL'D

588C MICROWAVE PULSE COUNTER B110875 Not Cal'd above 18 GHz.

70420A OPT 001 TEST SET B112149 See Agilent Certificate # 1-285378763-1

70427A DOWN CONVERTER B112150 TO Directed Limitation. AM Detector Noise Floor Not Cal'd. P/O E5504BOPT01, 406.406.E18. S/N 3816A00556

778D Directional Coupler F041205 Operational Check Only. Monitor all outputs. NPC

798C DIR COUPLER A223145 SEE CHART S/N 07457; CBU

E8257D LOW NOISE SIGNAL GENERATOR J290307 No Parameter cal'd above 18GHz

8340B SYNTHESIZED SWEEPER A223049 NOT CAL'D ABOVE 18GhZ. SINGLE SIDE BAND PHASE NOISE NOT CAL'D. HARMONICS OF 18 GHz CAL'D UP TO 9GhZ ONLY

No Parameters Cal'd above 18 GHz.

8340B SYNTHESIZED SWEEPER A499995 NOT CAL'D ABOVE 18GHZ, SWEPT FREQUENCY ACCURACY AND PHASE

SSB Phase noise Not Cal'd. No Parameter Cal'd > 18 GHz. Fan Noise sidebands approx 2.8KHz from carrier <55dBc.

NOISE NOT CAL'D, HARMONICS CAL'D TO 2nd HARMONIC OF 9GhZ. XTAL not cald >0db

8481H PWR SENSOR B204458 NOT CAL'D ABOVE 9GHZ. SEE CAL CHART S/N 1925A04216

Not Cal'd above 13 GHz. See Cal Chart. S/N 1925A04216

8482A PWR SENSOR A223338 SEE CAL CHART S/N 2349A10043 P/O 436A OPT E41; CBU

8485A PWR SENSOR B204560 SEE CAL CHART, NOT CAL'D ABOVE 18GHZ, USE APC-N ADAPTER S/N 02525; S/N 2347A02525 P/O 436A OPT E41; CBU

8485A PWR SENSOR C764474 NOT CAL'D ABOVE 18GHZ; P/O 436A OPT E41; S/N 2703A05023; CBU

Not Cal'd above 18 GHz. See Cal Chart. Referenced to adapter s/n 2703A05023. P/O 436A Opt E41/ CBU

8494OOPT001 0-11 dB Step Attenuator A284885 Unit Designated NPC, Measure Attenuation Prior to Use drj 7/19/08

8496AOPT001 ATTEN VAR A222866 CAL'D FROM 10MHZ TO 4GHZ, 110 db position not cald

8496BOPT001 ATTEN VAR A223137 0-100 db steps cald only

Full CAL DC TO 2 GHZ, ABOVE 2 GHZ 0dB to 60dB CAL'D ONLY

8502A(W)DETECTORS 8502A PEAK POWER ME A220302 P/O 8502A w/ Detectors jlp 29 apr 09

8502A(W)DETECTORS 17071 DETECTOR C875365 NOT CAL'D ABOVE 18GHZ; Calibrated for N type measurements using adapter sn 365; P/O 8502A w/detectors jlp 4/15/9

Not cal'd above 18 GH, use user supplied cal factors, se chart, calibrated only for N-Type Measurements using adapter SN 365

86633B Modulation section C875895 CBU

86603A RF Section C875506 CBU

8901AOPT001 Modulation Analyzer A222828 CBU

8902AOPT30 MW MEASUREMENT RECEIVER B203966 CAL'D TO 8902MS SPECS, POWER REFERENCE OUTPUT +/- 2% (TO DIRECTED) Special Calibration Meeting OPT 050 specs. P/O 8902MS no OPT 002. Para 4.3 thru 4.9 cal'd

No limitation

8902MS 8902AOPT030,0 MEAS RECEIVER A495475 POWER REFERENCE OUTPUT +/- 2% (TO DIRECTED)

Special Cal meeting POT050 Specs.Cal"d to 8902MS (OPT H15) Specs. (T.O. Dir) Frequency Counter Sensitivity not cal'd. P/O 88902MS

8902MS 18A50 PREC AIR LINE C764786 SWR LESS THAN 1.03, 1 - 18 GHz ONLY AS PER T.O.; P/O 8902MS; S/N 701021

8902MS 8662a B110970 SSB PHASE NOISE NOT CAL'S. NO PARAMETER CAL'D>18 GHZ. ATTENUATOR CAL'D TO -90DBM. >=2.1 GHZ HARMONICS < 55DBC P/O 8902MS

8902MS 8662A B110971 Not Cal'd > 18 GHz. Attenuator Cal'd to -90dBm. >/= 2.1 GHz Harmonics < -55dBc. SSB Phase Noise & Residual FM Not Cal'd. (prev). P/O 8902MS

909A OPT012 Termination B111371 Cal'd to 1 GHz for VSWR < 1.06

909A OPT012 Termination J287124 S/N 287124. Cal'd to 1 GHz for VSWR < 1.06

900-G10/ACP-I STANDARD ATTENUATOR C875170 SEE AFPSL CERTIFICATE OF CALIBRATION. CALIBRATED AT 30 MHZ ONLY.9.980DB ACCURACY +/- .010DB; S/N 1166

SEE AFPSL CERTIFICATE OF CALIBRATION REPORT NO. 063390036. TO DIRECTED LIMITATION. CALIBRATED AT 30 MHZ ONLY.

989C943H04 Attenuator B194998 Cald +/- 1 dB. NPC. 21 Feb 1991

9610A/AF-75 75-Ohm Leveling Head (N64) E225429 See Fluke Certificate# F16128 dtd 20070913. 9610A/AF-75, S/N 915152525. Cal'd w/9610A/AF, E225428, S/N 915152386. CBU

ATT-0219-10-NNN-02 ATTENUATOR B111618 DC TO 18GHZ, 10 +/- 0.5 DB

ATT-0219-10-NNN-02 ATTENUATOR B111617 DC TO 18GHZ, 10 +/- 0.5 DB

ATT-0219-10-06-NNN-02 ATTENUATOR B111615 DC TO 18GHZ, 6+/- 0.3 DB

ATT-0219-06-NNN-02 ATTENUATOR B111616 DC TO 18GHZ, 6+/- 0.3 DB

AN/UPM-155 8000000218-1 RADAR TEST SE C875313 P/O AN-UPM/155; CBU

AS4 ATTEN STD SET A220834 SEE AFTO FORM 249 FOR CHARTED VALUES

50-6 (6 DB) Attenuator Not Cal'd. See Cal Chart

E448A Opt 107 Spectrum Analyzer E225741 Noise sidebands ≥ 6 MHz offset certified to ≤ - 150dBc/Hz and at ≥10 MHz offset certified to ≤ -153 dBc/Hz. Other Input Related and General Spurious Responses will be certified to 18 GHz only. Audio Distrotion is only Cal'd to 100 KHz. T.O. Dir. No parameter Cal'd above 18 GHz.

E8257 Signal General J287742 No parameters above 18 GHz cal'd; Modulation deviation Cal'dto 400KHz only

AS-4 Attenuator Set C983274 50-6(6dB) Attenuator Not Cal'd (Previous). +/- 0.5 dB from charted value and at charted frequencies

DLM2000 DIGITAL LIGHT METER B111853 20.200 Fc and 200/2,000 Lux ranges accy: +/- 3% of reading. 2,000 fC and 20,000 Lux ranges accy: +/- 5% of reading. (TO Directed)

E8257D-520-HA1-UNX-1EA-1E1-UNT LOW NOISE SIGNAL GENERATOR J290309 Monitor All Outputs. P/O E5504BOPT001,406,406,E18

F1116N STANDARD THERMISTOR MOUNT C455566 See AFPSL Cert of Cal. Report# 070190024 Model F1116N S/N 877 C784062

Cal'd from 0.1 to 10 MHz TO Directed drj 9/16/08

F1109N STANDARD THERMISTOR MOUNT A793123 See AFPSL Cal. Cert. Report# 062130117 Model F1109N(w)5184 s/n 387(w)AJ9915 A518979

AFPSL Extended Calibration.

HPDC1 HIGH POWER DIRECTIONAL COUPLER A907285 SEE AFPSL CERTIFICATE OF CALIBRATION REPORT # 060110013 MODEL HPDC1 S/N 1500 A523409

MG3693A Signal Generator B111627 Frequency Display Resolution, 0.1Hz > 10 GHz. Phase Modulation not Cal'd. (TO Directed). Ext AM/FM opts not cal'd. Attenuation not Cal'd < -100 dB. No Parameter Cal'd > 18 GHz. SSB Phase Noise and Residual FM not Cal'd.

MG3694A Signal Generator B112120 No Parameter Cal'd > 18 GHz. Attenuator Cal'd to -100 dB. (prev) SSB Phase Noise Residual FM not Cal'd. T.O. Dir: Frequency Resolution < 10 GHz 0.1Hz, >10GHz 1Hz. P/O 8902MS

P752C DIR COUPLER A223164 COUPLING VARIATION +/- .7db (CBU)

P752D DIR COUPLER A223162 DIRECTIVITY > 30db (CBU)

PMCS-1A 436AOPT022 POWER METER A222353 POWER REFERENCE OUT +/- 2% (TO DIRECTED)

1025A Load B111652 VSWR not Cal'd

1025A Load B111653 VSWR not Cal'd

PMCS1B 1805A RF PWR LV CTL A495479 CAL'D FOR 1mW DC SUB POWER ONLY; LOG DRIVER NOT CAL'D P/O PMCS (PREVIOUS)

DC Substituted Power Cal'd at 1 mW only. LOG Driver not Cal'd. P/O PMCS1B (Previous) 27 Nov 06

PPTS 101 PULSE POWER TEST SET F041159 NPC/ Monitor all outputs

Q8486A POWER SENSOR C764816 CBU

Q8486A POWER SENSOR F041114 SEE CAL CHART; P/O 436A OPT E41; CBU

R8486A POWER SENSOR F041115 SEE CHART; P/O 436A OPT E41; CBU

R8486A POWER SENSOR C764915 SEE DATA SHEET; S/N A02056; P/O 436A OPT E41; (CBU)

N5532A-550 50 GHz Sensor Module E225746 Cal'd from 50 MHz to 50 GHz P/O N5530SE50 CBU jlp 20090410

K8

067-0625-00 PEAK TO PEAK DETECTOR E083128 SEE AFPSL CAL REPORT A164327

067-1338-00 CALIBRATION STEP GENERATOR C784862 SEE AFPSL CERTIFICATE OF CALIBRATION REPORT NO. 062000166. T.O. DIRECTED

LIMITATION CERTIFIED FOR RISETIME ONLY, CERTIFIED VALUE: 15.9ps

1432J RES DECADE A223045 zero ohms = .03; 1 ohm step cal'd to +/-.5% of rdg; 10 OHM STEP CAL'D TO +/- .3% OF Rdg

1616 PREC. CAPACITANCE BRIDGE A220811 CAPACITANCE RANGE AND ACCURACY IS DOWNGRADED TO +/- 100ppm AT Item is no longer here

1KHZ FROM 0.01 Pf to 1uF. AT OTHER FREQUENCIES TO 10 KHZ, ACCURACY

IS +/- [100ppm +(CuF)(fKHZ)ppm]. ALL OTHER CAPACITANCE RANGES

AND TRANSFORMER NOT CAL'D.

E007504 Capacitance Range and Accuracy is downgraded to +/- 100ppm @ 1kHz from 0.01pF to 1uF; at all other frequencies to 10kHz, accuracy is +/- [100ppm + (20 CuF)( FkHz)2 ppm]. All other Capacitance Ranges not certified. (TO Directed) P/O 1621

1689M RLC DIGIBRIDGE F041106 CBU

240C RATIO BRIDGE A222900 CAL' AT 23.4 DEG C

34401A Digital Multimeter J287412 AC Voltage and AC Current Not Calibrated Below 10Hz. (TO Directed)

This is a new item purchased with Reimbursable Funds

34970 CONVERTER THERMAL VOLT A495357 SEE AFPSL CERTIFICATE OF CALIBRATION. S/N 1324

100KHZ, 500KHZ and 1 MHZ cal'd only

4310AF TEMPERATURE STABILIZED RESISTANCE STANDARD

473292 TEST UNIT CAPACITANCE CALIB. A222955 SEE AFTO 249 FOR ACTUAL VALUES/CBU

4708 OPT20,30,80,90 AC VOLTAGE CALIBRATOR C454103 AC AMPS NOT CAL'D/ CBU

5000 PHASE ANGLE CALIB STD A222903 PHASE NOT CALIBRATED BELOW 400HZ/ CBU

5100B METER CALIBRATOR A439994 DC VOLTAGE CALIBRATED ONLY/CBU

Low & High Voltage Cal'd Only; CBU

5220A TRANSCONDUCTANCE AMP. C875338 COMPLIANCE VOLTAGE LIMITED TO +/- 50uV. ACA 5 KHZ +/- 3% (PRIVIOUS) ACA & FR DOWNGRADED TO +/- (.1% OF OUTPUT +1mA). 30HZ TO 2KHZ; CBU

5300 SYNCHRO RESOLVER STD E087596 T.O. Directed Resolver function not cal'd above 3Khz

530S741 SYNCHRO RESOLVER STD A223027 CBU

5520A/AF MULTI-PRODUCT CALIBRATOR B110948 PHASE CALIBRATION NOT CAL'D

5440BAF DC VOLTAGE CALIBRATOR A500388 DIVIDED OUTPUT: 0 - 220mv CAL'D TO +/- (18ppm +.5uv),

0.22 - 2.2V CAL'D TO (+/- 11ppm + 1.0 uv); CBU

This item was NRTS'd and Replaced

5440BAF DC Voltage Calibrator A425614 Monitor All Outputs. CBU.

This item was received as Serviceable from Supply. However, looking at PAMS History you can see it was a problem child of Laughlin AFB. They did not NRTS it as they should have, they turned it in Serviceable. This item is crippled, but it does what we need on the occasional basis when a 5720 might not have enough oomph.

5700 A/NAF CALIBRATOR F041105 22mA AC RANGE AT 20 HZ IS DOWNGRADED TO +/- (750ppm OF OUTPUT +400nA) T.O. DIRECTED

5720A CALIBRATOR F041505 20mA AC RANGE AT 20 HZ IS DOWNGRADED TO +/- (550ppm OF OUTPUT +

400 nA) AND 22 mA ACC RANGE at 5 KHZ IS DOWNGRADED TO +/- (550 PPM OF OUTPUT + E087291

700nA)

5790A/AF AC MEASUREMENT STD E087290 See Certificate of Calibration: 081780073. Internal Date will not agree with 99's date calibrated. AFTO Form 99 is the authority. Perform zero Cal at least every 30 days. TO Directed. E087295

E087270

5790A/AF03 AC MEASUREMENT STD E087281 See Certificate of Calibration: 080780029. Internal date will not agree with 99s date calibrated-AFTO Form 99 is the authority. Perform Zero Cal at least every 30 days. TO Directed Limitation

6000 PHASEMETER A626468 +/- .1 DEGREES 6KhZ TO 50KhZ (T.0.); NOT CAL'D BELOW 400Hz (PREVIOUS)

NOT CAL'D BELOW 400HZ

6517AAF Terra ohm meter E087838

6620 PRECISION PHASEMETER C453897 NOT CAL'D BELOW 400HZ. REMOVED NUMEROUS LIMITATIONS.

Cald' 100 mVRMS to 120 VRMS. +/- 1 Degree @ 10 Hz to 50 kHz. (Previous)

5520A/AF CALIBRATOR B110948 PHASE NOT CAL'D.

720A Kelvin Voltage Divider E096430 CBU drj 2/9/09

732A DC REFERENCE STANDARD C784617 1 VDC "=" 1.0000165, 1.018 VDC "=" 1.0180230, 10 VDC "=" 10.0000419/ CBU

734A/AF DC REFERENCE STANDARD C455765 See AFPSL Certificate of Calibration Report for 734A/AF S/N 6230055 and 732B/AFs B111026, B111027, B111028 and b111029. 1.018 V Output Not Specified by OEM

742A-1 RESSITANCE STANDARD E228284 Resistance Value: 1.000009537 Ohms. Uncertainty: +/- 8.83 ppm. Temp. Range: 18 Deg C to 28 Deg C.

750EL AMP DC A222946 OUTPUT CAL'D TO +/- .15%

10/23/02 NPC

752A REFERENCE DIVIDER A222906 PERFORM SELF TEST BEFORE USE (PAGE 2-3, PARAGRAPH 2-17) CBU

8100 TRANSCONDUCTANCE AMP E087007 NOT CAL'D ABOVE 20 AAC AND 10 KHZ. (T.O. DIRECTED) S/N 170/ CBU

Not Cal'd above 20AAC on the 100A Range & above 10KHz on all ranges (TO Directed)

825 RESISTANCE BOX A222966 ZERO RESISTANCE 0.0158 OHMS, ZERO RESISTANCE SUBTRACTED FOR

DECADES < 1, 10 OHMS PER STEP

NRTS 9

825 RESISTANCE BOX A756394 Zero Ohms </= to 0.024. Compensate for Zero Ohms for 1 Ohm range. Accuracy is +/- 1 % of setting on all dials.

835 PHASE SHIFTER C454592 NOT CAL'D BELOW 400HZ

8840AAF DMM A222306 ACV NOT CAL'D ABOVE 19 KHZ (PREVIOUS) INFO ONLY: 200 OHMS RANGE CAL'D IN 4 WIRE ONLY

RESISTANCE CAL'D TO +/- .06%

8840AAF DDM A411169 200 Range Cal'd in 4 wire only TO Directed

8840AAF DDM C029335 200 Range Cal'd in 4 wire only TO Directed

8840AAF DMM A222304 DC RATIO NOT CAL'D. INFO ONLY: 200 OHM RANGE CAL'D IN 4-WIRE

ONLY. (T.O. DIRECTED)

9210 CURRENT SHUNT A222959 SEE CAL CHART; CBU A715325

9211A CURRENT SHUNT A899914 SEE AFPSL certification of calibration report No. 081020064 Model 9211A S/N 54357 drj 9/16/08 A175245

EL-9800 Current Shunt Set E087375 See AFPSL Certificate of Calibration for limitations specified in the TO. Report No. 06144082. Shunts 16510, 16530, 16550, and 16580. Model EL-9800. Set 165

938 CAPACITANCE METER A224380 INDICATION ONLY. DO NOT USE FOR QUANTITATIVE MEASUREMENTS; NPC E087393

AH2700A CAPACITANCE BRIDGE E087708 SEE AFPSL CERTIFICATE OF CALIBRATION REPORT NO.061710065

AVM 100 NULL DETECTOR C983512 1uV RANGE NOT CAL'D

AVM-2000 NULL METER J283101 100nV & 300nV Range Not Cal'd. Standardization/Verification required w/in 24 hours before use or as needed before use, IAW ComData Preparation for Use. (T.O. Dir).

DT72A AC VOLTAGE DIVIDER A497694 > OR = TO 50HZ TO 1KHZ, +/- 2 PPM; > 1KHZ [( KHZ SQUARED x 2)=PPM] (TO DIRECTED); CBU

>/= 50 Hz to 1 kHz, +/- 2 ppm, > 1 kHz [(kHz2 X 2) = ppm]. TO Directed. CBU A074056

DT72A AC VOLTAGE DIVIDER A639479 EXCHANGE STANDARD. SEE AFPSL CERTIFICATE OF CALIBRATION: 072260050. Model DT72A. S/N AA2040388DT72A. TO Directed Limitation: Limited from OEM Specs due to AFPSL Standards.

DA1855A DIFFERENTIAL AMPLIFIER J287512 Gain X10 Accuracy +/- 2% of setting/CBU

DB62 DECADE RESISTOR A222960 ZERO OHM = .0324 OHM; 1 OHM/STEP CAL'D TO +/-(.36% + .006 OHM);

100 OHM/STEP CAL'D TO +/-(.05% + .006 OHM)

Zero Ohms = 0.01205 Ohms. 1 Ohm/Step Cal'd to +/- (0.36% + 0.0006 Ohms) 100 Ohm/Step Cal'd to +/- (0.05% + 0.006 Ohms). Previous

DB62 DECADE RESISTOR A222957 ZERO RESISTANCE AT TIME OF CAL .0096 OHM; 100 OHM/STEP +/-(.03% + .006

OHM); 1MOHM CAL'D TO +/-(.0412% + .006 OHM) (LACK OF STANDARD)

Zero Ohms at time of Cal: 0.0168 ohms. 100 Ohm/Step Cal'd to +/- (0.03% of setting + 0.0006 Ohms). Compensate for Zero Ohms of first 3 decades. E087129

EL9800 CURRENT SHUNT SET E087375 SEE AFPSL CERT OF CALIBRATION REPORT # 061440082 SHUNTS # 16510, 16530, 16550 AND 16580

HCS1AF AC CURRENT SHUNTS A495309 SEE AFPSL CERTIFICATE OF CALIBRATION. 100kHZ NOT CAL'D ABOVE

20mA. S/N 0943500068700

See AFPSL CERTIFICATE OF CALIBRATION. TO Directed Limitation: Cal'd from 40 Hz to 20 kHz Only.

MD1 FUEL QTY GAGE TSTR A244644 MONITOR ALL OUTPUTS ( NPC)

PMCS1B 3478A DMM A495474 30 Meg ohm Range not Cal'd; Cal'din 4 wire ohn mode only; P/o PMCS1 11 May 09 jlp

30 Megohm Range not cal'd; P/O PMCS1

QUAD10 PHASE COMPARATOR ACCESSORY A220299` 100V RANGE ABOVE 20KHZ AND 300V RANGE NOT CAL'D (TO DIRECTED) This item is no longer here

RS925D RESISTANCE STANDARD A222901 CAL'D AT 22.42 DEGREES CELSIUS AND 41% RELATIVE HUMIDITY.

1K OHM STEP AND HIGHER TO +/- 20PPM, 100 OHM STEP +/- 30PPM, 10 OHM

STEP AND LOWER +/- (40PPM + .001 OHM) TO DIRECTED

B110433 TO Directed Information for Temp Coefficients This item is no longer here

RS925D RESISTANCE STANDARD A222945 CAL'D AT 24 DEGREES CELSIUS AND 32% RELATIVE HUMIDITY.

> OR "=" 100OHM/STEP, +/- 3PPM/DEGREE CELSIUS; 10 OHM/STEP,+/- 15 PPM/DEGREE CELSIUS; < OR "=" 1 OHM/

STEP, +/- 20ppm/DEGREE CELSIUS, WIRING AND SWITCHES +/-50 uOHMS/degree Celsius (T.O. DIRECTED)

AFPSL Cal'd RS925D F273307 TO Directed Information for Temp Coefficients

RX1LM T/ADAPTER A222933 S1 POSITION 4 (95KM OHM NOT CAL'D), S2 POSITION 10 (5KM OHM NOT

INSTALLED) SEE CHART FOR VALUES

See Charts for Actual Values

RX1LM HI MEG RESISTOR J287198 See Attached Chart for Values & Voltages

RX1LM HI MEG RESISTOR A495314 UNIT CAL'D @ 20V DC SEE ATTACHED TAG (CBU)

See attached Chart for values and voltages C453560

SR104 STANDARD RESISTOR A008294 SEE AFPSL CERTIFICATE OF CALIBRATION REPORT No. 063490056 A925662

SC1000 CAPACITOR A500147 See AFPSL Certificate of Calibration Report No. 052770038

SR1010-1 RES TRANSFER STD A222951 ACCURACY +/- 100 PPM CAL'D @ 21.6C (CBU)

SR1030 RESISTANCE STANDARD C875627 CBU

SR1030-1 RESISTANCE TRANS STANDARD A220486 SEE CHART +/- 70 PPM (CBU)

SR103010 RESISTANCE TRANS STANDARD A220487 SEE CHART +/- 70 PPM (CBU)

SR1030100K RESISTANCE TRANS STANDARD A220491 SEE CHART (CBU)

SR103010K RESISTANCE TRANS STANDARD A220490 SEE CHART

(CBU)

SR1060 STANDARD RESISTOR SET A224428 100 OHM, 1 KOHM, 10 KOHM AND 100 KOHM BOXES CAL'D TO +/- 50ppm

1 OHM AND 10 OHM BOXES CAL'D TO +/- 70 PPM, CAL'D AT 23.00C, SEE CHARTS

FOR VALUES

SS32 STANDARD CAPACITOR KIT A222953 SEE CALIBRATION CHART FOR ACTUAL VALUES

ZM16BU DECADE RESISTOR A222939 MONITOR ALL DECADE SETTINGS BEFORE USE (NPC) (NRTS'd; Replaced with F466516)

F466516 NPC; Monitor all outputs

4360 Shunt A222920 CBU Old A870713

1852A HIGH POWER STANDARD REF SET A161946 SEE AFPSL CERTIFICATE OF CALIBRATION REPORT # 062680119 MODEL 1852A S/N 024

ASL Coupler Frequency Cal'd from 300 to 1000 MHz Only. See AFPSL Certificate of Calibration Report# 062680119

AS-4 PRECISION ATTENUATOR SET A220834 SEE CHART FOR CHARTED VALUES

50-6(6dB) Attenuator Not Cal'd (Previous). +/- 0.5 dB from charted value and at charted frequencies

438A POWER METER A220818 POWER REFERENCE OUTPUT ACCURACY +/- 2% (T.O. DIRECTED)

8340B SYNTHESIZED SWEEPER A222104 MAX LEVEL OUTPUT 5DBM FROM 13GHZ TO 18GHZ. HARMONICS CAL'D UP TO 2ND HARMONIC OF 96HZ. SPURIOUS SIGNALS BETWEEN 13.5 GHZ AND 18 GHZ CAL'D TO LESS THAN -40 DBC. NO PARAMETERS CERTIFIED ABOVE 18 GHZ.

No Parameter Cal'd > 18 GHz. Monitor Pulse Amplitude. (para 4.11). [Previous limitations removed.] 13 Dec 07

TS3427ARN TIME INTERVAL TEST SET A222708 0-1uS DELAY ADJUST NOT CAL'D/cbu

64A PRECISION STEP ATTENUATOR A222819 DC NOT CAL'D. INSERTION LOSS +/- 2DB. DRUM B CAL'D +/-.2DB

DC NOT CAL'D. Cal'd from 10 MHz to 1300 MHz Info: Specs from AFCAV.

3500 FILTER A222838 CBU

8496B OPT 001 ATTENUATOR/110DB A222864 100-110DB POSITIONS NOT CAL'D. CAL'D FROM 10MHZ-18GHZ

1316-3000KB OSCILATOR A222894 Deleted limitation

548A MICROWAVE FREQUENCY COUNTER A222806 NOT CAL'D ABOVE 18GHZ. BAND 4 NOT CAL'D (PREVIOUS)

251-400V AC POWER SOURCE A223046 MONITOR ALL OUTPUTS; NPC

3045C-20 DIRECTIONAL COUPLER A223147 CBU

3045C-20 DIRECTIONAL COUPLER A223149 CBU

154397 TRANSPONDER TEST KIT A223041 NCR

3002-30 COAXIAL DIRECTIONAL COUPLER A223170 SEE CHART FOR COUPLING VALUES

3043B-10 COAXIAL DIRECTIONAL COUPLER A223171 CBU

E204247

478AH73 Thermistor Mount E204301 See AFPSL Certificate of Calibration Report N. 081400096 . Cal'd from 10 to 1090 MHZ Model 478A-H73 S/N 79683 drj 7/1/08 E071382

478A-3 VOR BEARING STANDARD A487593 SEE AFPSL CERTIFICATE OF CALIBRATION REPORT #011710043 MODEL 478A3 S/N 366 SEE REVERSE

067-1338-00 CALIBRATION STEP GENERATOR C784862 CERTIFICATE FOR RISETIME ONLY; SEE AFPSL CERTIFICATE OF CALIBRATION REPORT # 021760080 CERTIFIED VALUE: 16.4 ps S/N B010353

015-0611-00 PROGRAMABLE PULSE HEAD A494212 P/O SICL F7529A2 TYPE 2

P/O F7529A2TYPEII. CBU

CG50110PT01 Calibration Generator A494215 Low Amplitude Edge (50 ohm load only) +/- 4%; P/O F7529A2TYPEII CBU

015-0310-01 COMPARATOR A495409 NCR

9028 POWER ATTENUATOR B110685 DC - 4GHZ +/- .1DB; 4GHZ-10GHZ +/- 2DB; NOT CAL'D ABOVE 10GHZ

AS-6A ATTENUATOR SET A500168 CAL'D AT 10MHZ, 4.5GHZ, 9GHZ, 13.5GHZ AND 18GHZ; 20DB ATTENUATOR REMOVED FROM BOX FAILED TO MEET SPECS

3db, 10db and 20db attenuator cal'd only. 20db Atten. +/- 1.5db

8163Q STANDARD PLATINUM RESISTANCE THERMOMETER A858950 T.O. DIRECTED LIMITED CALIBRATION; SEE CALIBRATION CERTIFICATE FOR CALIBRATION LIMITATIONS AND UNCERTAINTIES S/N G91357

436A OPT 022 POWER METER A645711 POWER REF OUT, CAL'D TO +/- 2% (T.O. DIRECTED) P/O 436A OPT E41 A164327

067-0625-00 PEAK TO PEAK DETECTOR E083128 SEE AFPSL CAL REPORT

478AH73 THERMISTOR MOUNT B195418 SEE AFPSL CERTIFICATE OF CALIRBRATION; TEST INSTRUMENT CALIBRATED FROM 10 TO 1090MhZ; REPORT # 013340086 MODEL 478AH73 S/N 79797

11975A AMPLIFIER C764152 P/O 3048MS

CBU

4226-20 DIRECTIONAL COUPLER C764914 NO CAL CHART; CBU

4226-10 DIRECTIONAL COUPLER C875088 CBU

16934 POWER DETECTOR C875364 NOT CAL'D ABOVE 18GHZ. P/O 8502A WITH DETECTORS

See Chart of Calibration. For Freq. Corrections, use User Supplied Calibration factor in dB. P/O 8502A(W)Detectors

SR1030 1K RESISTANCE TRANSFER STANDARD C875616 CBU

TG501 OPT 1 TIME MARK GENERATOR C983135 1nS MARKER AMPLITUDE NOT CAL'D

11801C DIGITAL SAMPLING SCOPE E143026 CH 1 AND CH 2 POSITION CAL'D ONLY

CH 1 AND CH 2 POSITION OF SLOT 1 CAL'D ONLY

160AR OPT 1 LOW THERMAL SCANNER E087194 NCR

AFTO 350. Line A #8 Scanner not Working

4421-101 RF POWER METER DISPLAY E204695 NCR

FMAV MODULATION ANALYZER E225108 ANALYZER TOTAL HARMONIC DISTORTION CALIBRATION, NOT CAL'D

CALIBRATION VILID ONLY WITH CAL CORRECTION ON PO CIVS; T0 DIRECTED

SG503 LEVEL SINE WAVE GENERATOR F041108 OUTPUT AMPLITUDE NOT CAL'D. FLATNESS CAL'D TO +/-2% FROM 50-100 MHZ (T.O. DIRECTED) CAL'D W/ CABLE 012-0482-00; P/O F5030A1; CBU

28N50-2 50 OHM TERMINATION F041444 SWR < OR EQUAL TO 1.02, DC TO < OR EQUAL TO 4.545 GHZ; < OR EQUAL TO 1.005 + .0033 X F(GHZ), >4.545 TO 18 GHZ. S/N 807001

5345 ELECTRONIC COUNTER F041564 CH. A SENSITIVITY - 18 DBM

K5_K6

36 MXS ANDERSEN AFB BASE LINE LIMITATIONS FOR PHYSICAL DIMENSIONAL AREA

PART NO. NOMEN LIMITATION

ITEMS IN RED HAVE BEEN CHANGED OR DELETED

K5 B

2190A (W) Y2003 THERMOCOUPLE SIM. CALIB A483005 CAL'D FOR USE WITH J AND K THERMOCOUPLE ONLY. K RANGE -132C TO

0C +/-.4C, USE THERMOCOUPLE CARDS IDENTIFIED AS CALD WITH UNIT

ONLY, REFERENCE ZERO TO ICE POINT BEFORE USE. (CBU)

16 Aug 07; designated item CBU

Card Cal'd for Type K Only. Card Identified w/shoe tag. (Info) 13 Dec 07

2626-S Temp/Humidity Probe J287637 Temperature Cal'd +/- 1 Deg F. Humidity Cal'd +/- 3% RH.

(New item added to inventory. 1 Feb 08. SJN)

2626-S Probe, Temp/Humidity B112271 Temperature Cal'd +/- 1 Deg F. Humidity Cal'd +/- 3% RH.

2626-S Temp/Humidity Probe B112270 Temperature Cal'd +/- 1 Deg F. Humidity Cal'd +/- 3% RH.

2626-S Temp/Humidity Probe J287636 Temperature Cal'd +/- 1 Deg F. Humidity Cal'd +/- 3% RH.

(New item added to inventory. 1 Feb 08. SJN)

2626-S Temp/Humidity Probe B112208 Temperature Cal'd +/- 1 Deg F. Humidity Cal'd +/- 3% RH. S/N A5A633

3604 Dry-well Temp.calibration system C875576 TOD Not certified above 900 deg F.

Cal'd to 800°F 1/9/09 drj

402CP45 THERMOMETER C764801 NPC (ACCY+/- 1 DEGREE F) S/N #3

402CP45 THERMOMETER C764802 NPC (ACCY+/- 1 DEGREE F) S/N #6

402CP45 THERMOMETER C764798 ACCY +/- 1 DEGREE F S/N #1

402CP45 THERMOMETER C764800 ACCY +/- .4 DEGREE F (2 DIV); S/N #4; CBU

566 PSYCHROMETER A500169 Cal'd for use as a Psychrometer only. 3/31/08 drj

Cal'd at room temperture +/- 1 Deg F T.O. Dir

8113Q PLATINUM RES THERMOMETER A858950 TO DIRECTED LIMITED CALIBRATION. SEE CALIBRATION CERTIFICATE OR CALIBRATION LIMITATIONS

AND UNCERTAINTIES. SERIAL NUMBER G91357

DELETE EXCHANGE

5698-25 PLATINUM RES THERMOMETER E289765 T.O. DIRECTED LIMITED CALIBRATION. SEE AFPSL CERTIFICIATE OF CALIBRATION REPORT NO. 053550097; MODEL 5698-25 S/N 95090

720350-1 THERMOCOUPLE/mVOLT CALIB A223665 K=+/-2.5C/J=+/-2C/T=+/-2C. ENSURE THE CHECK READINGS ARE IN TOLERANCE PRIOR TO USE

TO DIRECTED. CHANNEL A CAL'D ONLY.

Ch. A mv output Cal'd 0-20mv only. Acc= +/-.03% of Rdg + 8LSD

9540A Digital Thermometer E204041 0-60 degrees celsius accy +/- .1degrees celsius

New limitation; 3 Jan 08: Cal'd to +/- 0.2 degrees C.

Cal'd from -15 to 60 degrees celsius

CT485B-110V TEMP HUMIDITY RECORDER C875321 TEMP. CAL'D +/-2F. RH CAL'D +/-5%

Humidity cal't at 20, 50 and 80 % +/-3% Temperture cal'd at 50,77and 90 degs +/-2 2 degs F

CT485B-110V TEMP HUMIDITY RECORDER C875323 RH cal'd +/- 5% Temp cal'd +/- 2 deg F; Temp cal'd @40,65 &90 Deg F +/- 2 deg F. Humidity cal'd @ 20, 50 & 80% RH. Digital display not cal'd (T.O. directed) cal'd w/probe S/N C877523

CT485B-110V TEMP HUMIDITY RECORDER B111000 Humidity cal'd at 20,50, 80% +/- 4% Tempture cal'd at 50, 77, 104 deg F +/- 2 deg F Cal'd with probe h95T6

CT485B-110V TEMP HUMIDITY RECORDER C875322 RH CAL'D +/-5%. TEMP CAL'D +/- 2 DEG F

Temp cal'd@ 50, 77 & 90 +/- 2 DegF; Humidity cal'd @ 20, 55 & 90 +/-3%RH; Digital display not cal'd ( TO directed) Cal'd w/ temp probe H9A T5

CT485-110V TEMP HUMIDITY RECORDER F033367 CAL'D +/- 2 DEGREES F; +/- 5% RH

Humidity cal'd at 20, 50, and 80% +/- 3%. Temp cal'd at 50, 77 and 90 degress F +/- 2 deg.. Cal'd w/probe H95-T6. Digital readout not cal'd. CBU

K170-6C ICE PT REF SYS SSA K120-4C A483146 TERMINALS 1 AND 4 CAL'D ONLY

PHT-770 Hygo-Thermometer B112106 Temp Cal'd @ 45, 65, & 90 Degrees F. Humidity Cal'd @ 20, 50, & 80% RH. P/O AUDITKIT40 (TI S?N: 9335184). [New item added 26 Feb 08. SJN]

K6

10: THIS BELONGS TO YULISTA GAGE BLOCK SET B111018 ACCURACY: +/- 20uIN. FROM STATED VALUE. See Report of Calibration number 200708294900 dated 28 Sep 2007. S/N 0145. P/O 598-10-18, S/N 0145.

Accy: +/- 20u" from state value; See calibration chart; P/O=598-10-18 20081021 jlp

120X E3M1K3A10000 C875018 Accy. +/-2 Div / CBU

1425-24 HOOK GAGE RODS A223512 23" rod +/- .0004", 9" & 7" rods +/- .00035", 11" & 17" rods cal'd +/- .0003".

5" rod +/- .00025", 3" rod +/- .00015"; S/N 21

See Charted Values

1425-24 Hook Gage Stand B110789 Cal'd +/- 0.0025"H20; Thermometer accuracy not verified P/O 1425-24 Hook Gauge Stand S/N is 35 jlp 13 May 08

185 MAGNETIC BACK MIRROR B203638 SEE AFPSL CERTIFICATE OF CALIBRATION; S/N 87133; T.O. DIRECTED LIMITATION; MIRROR FLATNESS < 10.0 uIN over central 90% / CBU

SEE AFPSL CERTIFICATE OF CALIBRATION; S/N 87133; T.O. DIRECTED LIMITATION; MIRROR FLATNESS < 10.0 uIN over central 90%

2000-0-C Magnahelic Gage (Airlock) C875010 Cal'd +/- .02" H20. Use in Vertical Position Only

2000-300-3 1LB DISK B111364 Accy: +/- 0.05%

2456 Piston gauge Monitor B111496 Perform standardization before use. P/O 2465A series

25-2002-00 MIKE MASTER A223245 CBU

2465-601-58500 PISTONS G151202 SEE AFPSL CERTIFICATE OF CALIBRATION, REPORT NO. 032310113 (T.O. DIRECTED) MODEL 2465/2460-SERIES I.R S/N TL-877 SICL P/O 2465-601-58500

G151203 SAME AS ABOVE EXCEPT MR S/N C-138

G151204 SAME AS 63 EXCEPT; HR S/N V-972R

G151201 SAME AS 63 EXCEPT:2465-781-SERIES S/ 37962

3461-1-1, 3461-5-30 P GAGE GPA A495466 ACCY: +/- 2 DIV P/O 3461-1-1

ACCY: +/- 1 DIV P/O 3461-1-1

3461-1-1, 3461-5-100 P GAGE GPA B204658 ACCY: +/- 1 DIV P/O 3461-1-1

3461-1-1, 3461-5-300 P GAGE GPA B204659 ACCY: +/- 1 DIV P/O 3461-1-1

3461-1-1, 3461-5-10000 PRESS GAUGE A495467 +/- 1div; NOT CAL'D ABOVE 5000PSI

3461-1-104 3461-35-1000 P GAGE GPM C764275 Not cal'd above 600 psi

3461-1-104 3460-150-3000 RELIEF VALVE C764276 NCR

3461-1-104 3460-150-1000 RELIEF VALVE C764277 CBU

CM 3461-35-3000 P GAGE GPM C764278 Cal'd +/- 1 div P/O 3461-1-104 11/18/08 jlp

36 GAGE BLOCK SET G037140 See AFPSL Certificate of Calibration Report No.082420052 Model 36; S/N 121702.7 T.O. Directed Limitation 11/17/08 jlp G151103

384E PARALLEL BARS C875035 NPC

400B5 UNIVERSAL CALIBRATOR C875583 CAL'D @ 73 DEGREES F +/-6 DEGREES F; ACCUACY: 0-0.1 inch +/- 75 u inch; 0-0.5 inch +/- .0001 inch; TO Directed high and low magniciation cal's to +/- 100uin CBU

400594 PISTON POSITION SENSOR J287915 Stnadardization/Verification required every 6 months IAW COM DATA, Operation & Maint. Manual dated 2006; Sensor S/N 7915; P/O PG 7601-SYS-AF 11/07/08

VACUUM SENSOR J287496 Accy is +/- 0.534 Pa from2 to 5 Pa and +/-0.632 Pa at 6 Pa and +/-0.731 Pa (T.O. Directed) S/N 292 P/O PG7601-SYS-AF

470 SINE BAR CALIBRATOR A221109 FLATNESS OF SURFACE NOT CAL'D. ANGLE CAL'D TO +/- 0.5% OF DEVIATION FROM CENTER (500 ARC SEC) OF MICROMETER OR +/- 0.05 ARC SEC, WHICHEVER IS GREATER. P/N 470, S/N 89106

8 GAGE BLOCK SET A991577 SEE CAL REPORT; ACC +/- 5uin /in FROM CHARTED VALUES

568, V BLOCK C875024 NPC

599-750 V BLOCKS C875036 NPC

599-920-52 PARALLEL BARS C875030 NPC

599-920-52 PARALLEL BARS C875032 NPC

599-920-64 PARALLEL BARS C875029 NPC

599-920-64 PARALLEL BARS C875031 NPC

599-920-8 PARALLEL BARS C875033 NPC

599-920-8 PARALLEL BARS C875034 NPC

599-920-84 PARALLEL BARS C875037 NPC

599-920-84 PARALLEL BARS C875038 NPC

599-920-88 PARALLEL BARS C875027 NPC

599-920-88 PARALLEL BARS C875028 NPC

7024083 T.I. Setting Standard B112095 PARRALLELISM +/- 40 UIN (T.O. DIRECTED)

711-T1 DIAL INDICATOR A223249 CAL'D IN CW DIRECTION ONLY; LABEL REACCOMPLISHED 95136; CBU

71-7020S VARIABLE OPT WEDGE J287201 SEE AFPSL CERTIFICATE OF CALIBRATION: 070720086 MODEL 71-7020S S/N 415216

T.O. DIRECTED LIMITATION: UNCERTAINTY +/-0.5 ARC SEC. P/O 71-7030

71-7020S VARIABLE OPT WEDGE A498453 SEE CERTIFICATE OF CALIBRATION

S/N 411626 AFTO FORM 99 (TO DIRECTED)

750-5 DOSIMETER CHARGER A481725 NCR

74z-0-0-193 torque wrench J287522 C?W only, set @ 141.611 oz/in, ACC +/- 6 % I.V.

74Z-0-0-79 Torque wrench J288044 CW only + side up; set @ 3.98in/lbs; -(0.88 in/lbs) + (1.32 in/lbs)

74Z-0-0-21 Torque wrench J288043 CW only + side up; set @ 8.85 in/ lbs; -(1.85 in lbs) + (1.15 in/lbs)

779 DIAL COMPARATOR B111440 ACC. +/- .00004 (2 DIV) P/O 779 S/N K1001580

81 GAGE BLOCK SET, WORKING F041655 Accy. +/- 20 uin from stated value. See cal report. Accessories:Flatness and parallelism cal'd only

82A2X GAGE BLOCKS F041655 SEE REPORT OF MEASUREMENTS

901B Digital Pressure Indicator F272616 Cal'd to +/- 0.04% FS up to 800psi

9191 RIGHT ANGLE IRON B111253 SQUARENESS CAL'D .0004IN TIR (TO DIRECTED) PARALLELISM CAL'D .0002 IN TIR (20081015 Limitation removed)

9192 ANGLE PLATE A222609 NPC

9194 ANGLE PLATE B111424 SQUARENESS ACCURACY; .0005 in TIR, FLATNESS ACCURACY; .0003 IN TIR; made CBU

9228 SINE PLATE B111417 PARALLELISM OF PLATE <300uin

A6000AF/RPM3 DHI PRESSURE CALIB. F405868 NOT CAL'D BELOW 100 PSIA OLD ID#

RANGES H2 AND H3 NOT CAL'D F041859

Leak test not performed; run autozero daily when used in gage mode. Run autozero at least every 30 days when used in absolute & when returned from shipment. Accy: +/- .025% of rng P/O HGC-30000-AF drj 5/7/08

AG16LM ANGLE BLOCK SET A724840 SEE AFPSL CERTIFICATE OF CALIBRATION REPORT NO. 063210097 FOR T.O. DIRECTED LIMITATIONS AND ACTUAL VALUES, MODEL: AG16LM S/N 52584.12 A448961

A5 Torque Wrench F041995 Cal'd CW only @ 8" lbs +/- 6 %, Cal'd with open end 1/4 "adapter S/N E23-2-6 and 5/16 adapter S/N E23-2-5

B SUPER MIC. A480455 MEASURING FORCE ON TAILSTOCK SET AT 16+/-2 OZ. TI NULL METER FOR NULL INDICATION ONLY

C3H3-10T LOAD CELL 20K E204570 SEE CERTIFICATE OF CALIBRATION / Cal'd with E218552 A882186

C3H3-30T LOAD CELL 60K C936017 SEE CERTIFICATE OF CALIBRATION / Cal'd with E218552 E289552

CM Gage F022130 Cal'd to +/- 1 div from 0-60 psi and +/- 2 div above 60 pse 9/4/08

CP225D Analytical Balance B112255 Perform Internal Calibration before use (and calibration). Calibrated with Control Module, S/N 19012604.

New item added 27 Dec 07 (SJN)

CP34001S Analytical Balance J287354 Peform External Calibration prior to use (and calibration) to achieve certified accuracy. See Note 2 in AFCAV entry. (25 Jan 08, SJN)

In order to achieve certified accuracy, perform external calibration prior to use (and calibration). Use MMS 10 kg (or Class F1 or better) to perform the external calibration. 4/4/08 drj

CX1 HIEGHT MEASURING INSTRUMENT G037273 LINEARITY +/- .0002 IN (T.O. DIRECTED)

D614-104 PENTA BLOCK A500616 ANGLE=90'-2"; LABEL REACCOMPLISHED 95137 (CBU)

A500616 This item was exchanged with Hickam's ID# B035809. There's was inop. & this one hasn't been here in over 13 years.

B035809 Actual Angle: 90 deg, 0' 3.1" +/- 1". NRTS-8; (Retaining for inventory Purposes only)

D615 REFERENCE MIRROR A496176 D615, S/N 4823 (CBU)

SEE AFPSL CERTIFICATE OF CALIBRATION S/N 4823 T.O. DIRECTED LIMITATION MIRROR FLATNESS ≤ 4.0 UIN

D616 MIRROR C764774 ACCURACY: FLATNESS 0-.000005 INCH MAXIMUM TO DIRECTED (CBU)

EXCHANGE STANDARD DELETED 20011205

DMP40 DIGITAL FORCE INDICATOR E218552 SEE CERTIFICATE OF CALIBRATION E218546

DPG100-250 DIGITAL PRESSURE GAUGE B110093 CAL'D TO +/- 1PSI

GX-2000 Analytiical Balance J287358 In order to achieve certified accy., perform internal cal. prior to use (and calibration). Direct Readout, Repeatability, and Shift Test cal'd. Linearity not cal'd. (T.O. Dir)

FCS3ASSC 10-25-.1 P/O FCS3ASSC1 C936247 SEE CERTIFICATE OF CALIBRATION AND DATA SHEET

(PART OF FCS-3A-SS-C1KIT # 88-110 S/N 10018

EXCHANGE STANDARD DELETED 20010823

FCS3ASSC 10-25-1 P/O FCS3ASSC1…