Attach_07_VAFB_Electrical_Material_Specifications_Part2.pdf

TSgt Rus se ll W ell s

ADSCO LINE PRODUCTS 03/02Please call for pricing.

Pole-Top Extension Stainless Steel

The steel pole-top extension solves the problem of installing new primary circuits on established poles.

• Used in pairs

• Use with the heel plate shown below

• All holes accommodate 5/8 inch bolts

Heel Plate Stainless Steel

The steel heel plate is used with the pole-top extensions to improve rigidity.

• Center hole is used to attach flat brace or 18 inch drop angle cross arm brace

• Fits top pole diameters from 5 to 13 inches

APPX. SHIPPING WT.

CAT. NO MATERIAL LBS. PER 100 PCS.

HP-125 1-4" PLATE 500

ANGLE

SIZE APPX. SHIPPING WT.

CAT. NO. LENGTH INCHES A B C D LBS. PER 100 PCS.

PTE-87 7' 3-1/2" 3 X 3 X 1/4 24 17-3/4 - 2 3920

PTE-148 12' 4" 3 X 3 X 1/4 33 24 30 2 6650

INCHES

This product was compiled by:

TSgt Russell C. Wells Vandenberg AFB, California

FA461019RA029 - ATTACHMENT 07

se ll W ell s

ADSCO LINE PRODUCTS 03/02Please call for pricing.

ADSCO

STAINLESS STEEL DEAD-END GRIPS

FOR USE ON STAINLESS STEEL STRAND: TYPE 302

FOR USE ON STAINLESS STEEL STRAND: TYPE 316

Catalog Applied Subset Rod Color Rated Number Size Units Wt/Lbs. Length Diameter Code Strength Size Type

AG-807 1/4" 100 59 28 4 .100 Yellow 9,500 1/4" 3W-7W

AG-808 9/32" 100 58 27 4 .100 Black 10,500 9/32" 3W-7W

AG-809 5/16" 50 40 31 5 .100 Orange 13,200 5/16" 3W-7W

AG-810 3/8" 50 62 37 5 .114 Green 18,000 3/8" 3W-7W

AG-811 7/16" 25 55 43 5 .138 Red 27,000 7/16" 3W-7W

AG-812 1/2" 20 60 50 6 .138 Blue 32,000 1/2" 7W-19W

AG-813 9/16" 10 50 60 6 .162 Yellow 36,000 9/16" 7W-19W

TYPE 302 STAINLESS STEEL ADSCO DEAD-ENDS

Per Carton Strand

Catalog Applied Subset Rod Color Rated Number Size Units Wt/Lbs. Length Diameter Code Strength Size Type

AG-907 1/4" 100 53 26 4 .100 Yellow 7,500 1/4" 3W-7W

AG-908 9/32" 100 58 27 4 .100 Black 9,550 9/32" 3W-7W

AG-909 5/16" 50 41 31 5 .100 Orange 11,500 5/16" 3W-7W

AG-910 3/8" 50 62 37 5 .114 Green 16,200 3/8" 3W-7W

AG-911 7/16" 25 55 43 5 .138 Red 24,000 7/16" 3W-7W

AG-912 1/2" 20 60 50 6 .138 Blue 30,000 1/2" 7W-19W

AG-913 9/16" 10 50 60 6 .162 Yellow 33,000 9/16" 7W-19W

Per Carton Strand

TYPE 316 STAINLESS STEEL ADSCO DEAD-ENDS

This product was compiled by:

TSgt Russell C. Wells se ll W ell s

ADSCO LINE PRODUCTS 03/02 Please call for pricing.

MATERIALS:

Grip – made of the same basic material as the strand they are designed for.

Identification Tag – shows catalog number, nominal strand size and strand diameter range.

Color Code – identifies correct strand sizes.

Cross over marks – mark A shows starting point for application on small diameter terminations. Mark B shows starting point for application on larger diameter terminations described on page 2.

GENERAL RECOMMENDATIONS

POWER GRIP DEAD ENDS are recommended for single wood poles associated with distribution construction and for guying transmission towers.

They are compatible to the strand and are ideal for use in coastal areas and in polluted areas.

APPLICATION INSPECTION

DEAD ENDS may be removed and re-applied a maximum of 3 times during new construction with-out damaging their performance characteristics, however they should not be reused after original installation.

DEAD ENDS are designed generally to hold the full rated strength of 90 to 110 ton of grade galvanized steel strand.

DEAD ENDS should be used on hardware that is held in a fixed position; the fitting should not be allowed to rotate or spin about the axis of the strand.

Further, they should not be used as tools; such as come-alongs, pulling-in grips, etc.

Lay direction of both the DEAD END and the strand should be the same. In most cases left hand lay is standard. For appearance and safety, the stranded tail should be cut as close as convenient to the cross over mark. If desired the strand tail can, instead, extend through the loop for grounding purposes.

DEAD ENDS retain a positive grip under all conditions whether the guy is relaxed or under tension. Once the legs of the DEAD END are in position, the assembly is complete and permanent.

DEAD ENDS will remain fully operative under the most difficult conditions, tension, impact, temperature extremes, in fact, any force to be met in functional performance. They will never relinquish their gripping power.

POWER

GRIP DEAD END

IDENTIFICATION

TAG

CABLED LOOP

COLOR CODE AND

CROSS OVER MARKS

LONG LEG

SHORT LEG

A B

This product was compiled by:

TSgt Russell C. Wells se ll W ell s

ADSCO LINE PRODUCTS 03/02Please call for pricing.

Lag Screws, Screw Eye Bolts Stainless Steel

Screw Bolts Stainless Steel

CATALOG NO. MIN. THREAD APPROX.

FETTER DRIVE FETTER DRIVE TWIST DRIVE SIZE LENGTH SHIP WT.

GIMLET POINT REG. POINT PILOT POINT PILOT POINT (INCH) (INCH) (LBS/100)

LS-415G 1/4 X 1-1/2 1-1/4 2.4

LS-420G LS-420 1/4 X 2 1-1/2 2.7

LS-425G LS-425 1/4 X 2-1/2 1-3/4 3.3

LS-430G 1/4 X 3 2 3.7

LS-525G 5/16 X 2-1/2 1-3/4 5.3

LS-625 3/8 X 2-1/2 1-3/4 8.8

LS-630G LS-630 LS-630P 3/8 X 3 2 9.9

KS-640 KS-640P 3/8 X 4 2-1/2 13

LS-830 LS-830P LS-830TP 1/2 X 3 2 19

LS-835 LS-835P 1/2 X 3-1/2 2-1/4 20

LS-840G LS-840 LS-840P LS-840TP 1/2 X 4 2-1/2 23

LS-845 LS-845P 1/2 X 4-1/2 2-3/4 26

LS-850 LS-850P LS-850TP 1/2 X 5 3 27

LS-1050 5/8 X 5 3 44

CATALOG DIAMETER APPROX. SHIP WT.

NO. (INCH) (LBS/100)

SEB-860 1/2 53

This product was compiled by:

TSgt Russell C. Wells se ll W ell s

2-35ADSCO LINE PRODUCTS 03/02 Please call for pricing.

SPECIFICATIONS

MATERIAL: BODY - AISI TYPE 316 STAINLESS STEEL

COTTER PIN: STAINLESS STEEL

Socket Eye

CATALOG NO. SE-30M-SS316

ULTIMATE BREAKING STRENGTH: 30,000 LBS.

DIMENSION IN INCHES: W = 1

R = 13/16

L = 2 1/16

DIA = 11/16

WEIGHT LBS./C: 1.40

This product was compiled by:

TSgt Russell C. Wells se ll W ell s

ADSCO LINE PRODUCTS 03/02Please call for pricing.

Strand-Eye Anchor Rods TYPE 316 Stainless Steel

Rolled threads are furnished on all rods up to and including ¾” diameter. 1” and larger have cut threads. Length of thread –3-1/2”. Manufactured to ANSI Standards.

STOCK LGTH APPROX. WT. STOCK LGTH APPROX. WT. STOCK LGTH APPROX. WT.

NO. FT. LBS. PER 100 PCS. NO. FT. LBS. PER 100 PCS. NO. FT. LBS. PER 100 PCS.

AR1-125316 5 300 - - - - - -

AR1-126316 6 450 - - - - - -

AR1-127316 7 500 - - - - - -

AR1-585316 5 590 - - - - - -

AR1-586316 6 664 AR2-586316 6 690 - - -

AR1-587316 7 766 AR2-587316 7 765 - - -

AR1-588316 8 830 AR2-588316 8 840 - - -

AR1-346316 6 960 AR2-346316 6 970 - - -

AR1-347316 7 1230 AR2-347316 7 1130 AR3-347316 7 1130

AR1-348316 8 1245 AR2-348316 8 1403 AR3-348316 8 1255

- - - AR2-349316 9 1460 AR3-349316 9 1460

- - - AR2-3410316 10 1520 - - -

AR1-108316 8 2300 AR2-108316 8 2310 AR3-108316 8 2310

- - - AR2-109316 9 2530 - - -

AR1-1010316 10 2600 AR2-1010316 10 2895 AR3-1010316 10 2895

- - - AR2-11410316 10 4400 AR3-11410316 10 4620

5/8" Diameter Rod --- Minimum Strength 16,000 Lbs.

3/4" Diameter Rod --- Minimum Strength 23,000 Lbs.

1" Diameter Rod --- Minimum Strength 36,000 Lbs.

1 1/4" Diameter Rod --- Minimum Strength 58,000 Lbs.

SINGLE EYE-Figure 2-6 DOUBLE EYE-Figure 2-7 TRIPLE EYE-Figure 2-8

1/2" Diameter Rod --- Minimum Strength 10,000 Lbs.

Figure 2-6 Figure 2-7

Figure 2-8

This product was compiled by:

TSgt Russell C. Wells se ll W ell s

ADSCO LINE PRODUCTS 03/02 Please call for pricing.

Thimble Eye Nut MATERIAL: SPECIFICATIONS: TYPE 316 Stainless Steel

Guying Hardware (cont.)

CATALOG

NUMBER FOR BOLT DIA. A" B" C" D" E" F"

TEN-58316SS 5/8" 1-1/2" 1-1/2" 7/8" 1-3/8" 1-7/8" 3"

TEN-34316SS 3/4" 1-1/2" 1-1/2" 7/8" 1-3/8" 1-7/8" 3"

DIMENSIONS-INCHES

STOCK FIGURE DESCRIPTION APPROX. WT.

NO. NO. BOLT HOLE SIZE LBS. 100 PCS.

AGA1-316 2-24 1- BOLT TYPE 11/16 1/4 X 1 1/2 X 4 1/8 84

AGA12-316 2-24 1- BOLT TYPE 13/16 1/4 X 2 X 4 1/8 114

AGA2-316 2-25 2- BOLT TYPE 9/16-13/16 1/4 X 1 1/2 X 7 118

AGA22-316 2-25 2- BOLT TYPE 9/16-13/16 1/4 X 2 X 7 1/4 150

GJH 2-26 1- HOLE MOUNTING 11/16 3/8 X 1 3/4 X 4 84

SP1-316 2-27 STANDARD 7/32 14 GA X 4 X 8 74

SP2-316 2-28 GUY HOOK TYPE 7/32 14 GA X 4 X 8 154

LP12-316 2-29 5/8 BOLT-2 HOLE 11/16 X 15/16 3/16 X 2 1/2 X 7 90

LP13-316 2-29 5/8 BOLT-3 HOLE 11/16 X 15/16 3/16 X 2 1/2 X 7 86

LP22-316 2-29 3/4 BOLT-2 HOLE 13/16 X 1 1/16 1/4 X 2 1/2 X 7 119

LP23-316 2-29 3/4 BOLT-3 HOLE 13/16 X 1 1/16 1/4 X 2 1/2 X 7 115

PBB-316 2-30 11/16 - 1300

LIFT PLATES

PUSH BRACE BRACKET

DIMENSIONS-INCHES

GUY HOOKS

ANGLE GUY ATTACHMENTS

STRAIN PLATES

This product was compiled by:

TSgt Russell C. Wells se ll W ell s

ADSCO LINE PRODUCTS 03/02 Please call for pricing.

Transformer Brackets Stainless Steel

These brackets support two transformers.

• Manufactured from flat steel welded onto a rigid frame

• Mounting slots accommodate ¾ inch bolts

• 1600 pound maximum total weight allowed

These brackets support three transformers and have these features.

• Extremely stable mounting on the pole

• Angled to have an aesthetically pleasing appearance

• Reversible plastic or steel mounting blocks that allow mounting transformers with 11-1/4 or 23-1/4 inch spacing between hanger brackets

• 1400 pounds maximum transformer weight at each position

• Allows pre assembly of all equipment and connections on the ground before being easily raised into place

A B R APPX. SHIPPING WT.

CAT. NO. INCHES INCHES INCHES LBS. PER 100 PCS.

TB-6375 26 6-3/8 4 2900

TB-400 26 4 4 2150

A B APPX. SHIPPING WT.

CAT. NO. INCHES INCHES LBS. PER 100 PCS.

CTB-43 43 60 11,500

CTB-21 21-1/2 60 11,500

This product was compiled by:

TSgt Russell C. Wells se ll W ell s

ADSCO LINE PRODUCTS 03/02Please call for pricing.

Turnbuckles - DROP FORGED

DROP FORGED HEX BODY

STAINLESS STEEL

1035 STEEL • 5:1 SAFETY FACTOR

USE FOR STRAIGHT OR IN-LINE PULLS ONLY

STUB ENDS

HOOK & HOOK

EYE & EYE JAW & JAW

HOOK & EYE

JAW & EYE

N O

T E

U

S E

W E

IG

H

T S

O F

E Y

E

E Y

E T

U R

N B

U C

K

LE

S T

O G

E T

A P

P R

O X

IM

A

T E

W E

IG

H

T S

O F

S T

U B

E N

D T

U R

N B

U C

K

LE

S

Federal Specifications FF-T-791 b Type 1 Form-1 Class 4

Federal Specifications FF-T-791 b Type 1 Form-1 Class 7

Federal Specifications FF-T-791 b Type 1 Form-1 Class 3

Federal Specifications FF-T-791 b Type 1 Form-1 Class 6

Federal Specifications FF-T-791 b Type 1 Form-1 Class 5

Federal Specifications FF-T-791 b Type 1 Form-1 Class 8

DIAMETER Avg. OVERALL

& TAKE-UP ends in closed with HOOKS JAW JAW in Inches position (in Inches) or EYES and EYE and JAW

1/4 x 4 8-1/4 .30 .32 .36

5/16 x 4-1/2 9-9/16 .63 .47 .52

3/8 x 6 11-7/8 .75 .76 .81

1/2 x 6 13-5/16 1.60 1.53 1.50

1/2 x 9 16-5/16 1.83 1.71 1.74

1/2 x 12 19-5/16 2.25 2.06 2.40

5/8 x 6 15-1/2 2.75 2.35 3.02

5/8 x 9 18-1/2 3.13 3.06 3.31

5/8 x 12 21-1/2 3.50 3.78 4.00

3/4 x 6 17 3.89 4.00 4.11

3/4 x 9 20 4.61 4.75 5.10

3/4 x 12 23 5.43 5.36 5.65

3/4 x 18 29 7.25 7.00 7.00

7/8 x 12 24-5/8 8.10 8.00 8.17

7/8 x 18 30-5/8 9.25 9.75 9.00

1 x 6 20-5/8 9.33 9.00 9.75

1 x 12 26-5/8 11.93 11.20 12.00

1 x 18 32-5/8 14.00 13.30 14.00

1 x 24 38-5/8 17.25 17.00 17.00

1-1/4 x 12 29-7/8 18.00 20.00 21.50

1-1/4 x 18 35-7/8 23.00 24.18 25.50

1-1/4 x 24 41-7/8 27.00 27.50 28.70

1-1/2 x 12 32-3/8 27.50 28.50 30.05

1-1/2 x 18 38-3/8 31.00 35.00 34.25

1-1/2 x 24 44-3/8 37.50 38.73 40.67

1-3/4 x 18 41-3/4 52.50 53.75 55.04

1-3/4 x 24 47-3/4 58.00 61.00 63.36

2 x 24 51-3/4 85.25 89.00 94.00

2-1/2 x 24 58-1/2 144.25 150.00 165.00

2-3/4 x 24 61-1/2 194.00 183.00 198.00

WEIGHT EACH in Lbs.

This product was compiled by:

TSgt Russell C. Wells se ll W ell s

ADSCO LINE PRODUCTS 03/02 Please call for pricing.

Turnbuckles - ENGINEERING DATA Dimensions and Strength

PROOF LOAD TWICE SAFE WORKING LOAD

ULTIMATE LOAD FIVE TIMES SAFE WORKING LOAD

Dimension “W” figured with stub screwed in as shown. To determine the overall length of longer takeup turnbuckles, add the difference in takeup.

SAFE working

LOAD

A B C D E F G H in Lbs.

1/4 5/8 1/4 13/32 9/32 1/2 1-5/8 5/8 500

5/16 7/8 1/4 15/32 9/32 1/2 2 11-16 800

3/8 7/8 5/16 1/2 5/16 19/32 2-3/16 13/16 1 200

1/2 1-1/16 3/8 5/8 13-32 3/4 2-3/4 1 2 200

5/8 1-5/16 1/2 3/4 1/2 1-1/32 3-1/2 1-5/16 3 500

3/4 1-1/2 5/8 15/16 9/16 1-9/32 4-1/8 1-5/8 5 200

7/8 1-3/4 3/4 1-1/8 11/16 1-15/32 4-27/32 1-7/8 7 200

1 2-1/16 7/8 1-3/16 25/32 1-21/32 5-17/32 2-1/8 10 000

1-1/4 2-13/16 1-1/8 1-3/4 1 2-3/32 7-3/16 2-5/8 15 200

1-1/2 2-13/16 1-3/8 2-1/16 1-1/16 2-15/32 7-7/8 3-1/8 21 400

1-3/4 3-3/8 1-5/8 2-3/8 1-1/4 2-29/32 9-3/8 3-1/2 28 000

2 3-11/16 2 2-1/2 1-9/16 3-17/32 10-7/8 4-3/16 37 000

2-1/2 4-7/16 2-1/4 2-7/8 1-9/16 4-5/8 13-11/32 5-5/8 60 000

2-3/4 4-3/16 2-3/4 3-1/2 1-5/8 5-3/8 15 6-1/8 75 000

DIMENSIONS in Inches

SAFE working

A B C D E LOAD in Lbs.

1/4 11/32 7/32 25/32 1-25/32 500

5/16 7/16 9/32 15/16 2-3/16 800

3/8 17/32 11/32 1-1/8 2-9/16 1 200

1/2 23/32 7/16 1-7/16 3-7/32 2 200

5/8 7/8 1/2 1-3/4 3-7/8 3 500

3/4 1 5/8 2-1/8 4-11/16 5 200

7/8 1-1/4 3/4 2-3/8 5-1/4 7 200

1 1-7/16 7/8 3 6-3/8 10 000

1-1/4 1-13/16 1-1/8 3-9/16 7-3/4 15 200

1-1/2 2-1/8 1-1/4 4-1/8 8-5/8 21 400

1-3/4 2-3/8 1-1/2 4-11/16 10 28 000

2 2-11/16 1-3/4 5-3/4 12-1/8 37 000

2-1/2 3-1/8 2 6-1/2 13-9/16 60 000

2-3/4 3-1/4 2-1/4 7 15 75 000

DIMENSIONS in Inches

SAFE working

A B C D E LOAD in Lbs.

1/4 1/4 13/32 29/64 1-21/32 400

5/16 5/16 1/2 1/2 1-31/32 700

3/8 3/8 39/64 9/16 2-23/64 1 000

1/2 1/2 25/32 21/32 2-15/16 1 500

5/8 5/8 1 27/32 3-11/16 2 250

3/4 3/4 1-13/64 63/64 4-33/64 3 000

7/8 7/8 1-3/8 1-1/8 5-3/16 4 000

1 1 1-17/32 1-1/4 5-27/32 5 000

1-1/4 1-1/4 1-13/16 1-1/2 7-7/32 5 000

1-1/2 1-5/16 1-3/4 1-7/8 8-11/32 7 500

DIMENSIONS in Inches

SAFE working

A R S T U W LOAD in Lbs.

1/4 4 4-3/4 3/8 2-5/8 10 500

5/16 4-1/2 5-7/16 15/32 2-21/32 10-3/4 800

3/8 6 7-1/8 9/16 4-7/16 16 1 200

1/2 6 7-1/2 3/4 4-1/4 16 2 200

5/8 6 7-7/8 15/16 4-1/16 16 3 500

3/4 6 8-1/4 1-1/8 4-3/8 17 5 200

7/8 6 8-5/8 1-5/16 4-11/16 18 7 200

1 6 9 1-1/2 5 19 10 000

1-1/8 6 9-1/8 1-9/16 4-15/16 19 12 400

1-1/4 6 9-1/8 1-9/16 5-7/16 20 15 200

1-3/8 6 9-3/4 1-7/8 5-3/8 20-1/2 18 000

1-1/2 6 9-3/4 1-7/8 5-3/8 20-1/2 21 400

1-5/8 6 10-3/8 2-3/16 5-5/16 21 25 000

1-3/4 6 10-3/8 2-3/16 5-13/16 22 28 000

2 6 11 2-1/2 6 23 37 000

2-1/2 6 13-1/2 3-3/4 6-1/4 26 60 000

2-3/4 24 31-1/2 3-3/4 6-1/2 44-1/2 75 000

DIMENSIONS in Inches

JAW

EYE

HOOK

STUB END

This product was compiled by:

TSgt Russell C. Wells se ll W ell s

ADSCO LINE PRODUCTS 03/02Please call for pricing.

Turnbuckles - Eye and Eye TYPE 316 Stainless Steel

Sail Guide with Ring TYPE 316 Stainless Steel

Other Sizes & Types - Call for Price

ADSCO PART SCREW CLOSED STD.

NUMBER DIA. LENGTH PKG.

TB3/16X23/4SS316 3/16" 2-3/4" 1

TB1/4X31/2SS316 1/4" 3-1/2" 1

TB5/16X43/4SS316 5/16" 4-3/4" 1

ADSCO PART STD.

NUMBER PKG

AKS-46-01 5

This product was compiled by:

TSgt Russell C. Wells se ll W ell s

ADSCO LINE PRODUCTS 03/02Please call for pricing.

Stainless Steel Wire Rope Clips TYPE 304 AND 316 (Drop Forged)

*Based on clean, unlubricated threads.

Minimum torque required to reach max. holding power

RIGHT WAY FOR MAXIMUM ROPE STRENGTH

When using U-bolt clips, extreme care must be exercised to make certain that they are attached correctly. The correct way to attach U-bolts is shown above; the “U” section is in contact with the ropes “dead-end” and is clear of the thimble. The “live-end”, carrying the load is gripped by the saddle of the clip. Also, the tightening and retightening of the nuts must be accomplished as required.

Caution: Never use any wire rope clip to directly connect two straight lengths of wire rope.

Minimum

HOW TO SIZE Number Torque Approx.

ORDER of Clips in Lbs. Ft Weight

Required Each

To order 1/8" 2 4.5 .05lbs use the 3/16" 2 7.5 .106

Prefix: 1/4" 2 15 .19

WRC-Size 5/16" 2 30 .30 followed 3/8" 2 45 .46 by SS- 1/2" 3 65 .68

T304 or 316 5/8" 3 95 1.0

Example: 3/4" 4 130 1.5

WRC-1/2SS304 1" 5 225 2.69

This product was compiled by:

TSgt Russell C. Wells se ll W ell s

ADSCO LINE PRODUCTS 03/02 Please call for pricing.

WIRE ROPE WEIGHT

DIA. SIZE EACH

in Inches A B C D E F in Lbs.

1/8 1-15/16 1-1/16 1-5/16 11/16 5/32 5/8 3.3

3/16 1-15/16 1-1/16 1-5/16 11/16 7/32 5/8 3.3

1/4 1-15/16 1-1/16 1-5/16 11/16 9/32 5/8 3.3

5/16 2-1/8 1-1/4 1-1/2 13/16 3/8 3/4 4

3/8 2-3/8 1-15/32 1-5/8 15/16 7/16 7/8 7.50

1/2 2-3/4 1-3/4 1-7/8 1-1/8 9/16 1-1/16 18.80

5/8 3-1/2 2-3/8 2-1/4 1-3/8 11/16 1-1/4 36.

3/4 3-3/4 2-11/16 2-1/2 1-5/8 13/16 1-1/2 60.

7/8 5 3-3/16 3-1/2 1-7/8 15/16 1-3/4 90.

1 5-11/16 3-3/4 4-1/4 2-1/2 1-1/16 2-3/8 105.

1-1/8-1-1/4 6-1/4 4-5/16 4-1/2 2-3/4 1-5/16 2-5/8 166.

1-1/2 7-1/2 5-3/8 5 3-1/4 1-9/16 3-1/8 325.

1-3/4 10-3/4 7-1/4 7-1/4 4-1/4 1-7/8 4-1/8 583.25

2 10-3/4 7-1/4 7-1/4 4-1/4 2-1/8 4-1/8 583.25

DIMENSIONS IN INCHES

Wire Rope Thimbles Stainless Steel

HEAVY DUTY

STANDARD

PER FED. SPEC. FF-T-276B, TYPE III • ALSO AVAILABLE WITH WELDED GUSSET

WELDED GUSSET PLATES AVAILABLE FOR GUSSET 2”, 2 1/4”, AND 2 1/2”

MEETS FEDERAL SPECIFICATIONS FF-T-276B, TYPE II

WIRE ROPE MAX. PIN WEIGHT

DIA. SIZE DIA. per 100 in Inches A B C D E F in Inches in Lbs.

1/4 2-3/16 1-1/2 1-5/8 7/8 13/32 9/32 13/16 6.5

5/16 2-1/2 1-13/16 1-7/8 1-1/16 1/2 11/32 15/16 11.25

3/8 2-7/8 2-1/8 2-1/8 1-1/8 21/32 13/32 1-1/16 25.00

7/16 3-1/4 2-3/8 2-3/8 1-1/4 3/4 15/32 1-3/16 50.00

1/2 3-5/8 2-3/4 2-3/4 1-1/2 27/32 17/32 1-7/16 51.00

9/16 3-5/8 2-11/16 2-3/4 1-1/2 29/32 19/32 1-7/16 51.00

5/8 4-1/4 3-1/8 3-1/4 1-3/4 1 21/32 1-5/8 75.00

3/4 5 3-3/16 3-3/4 2 1-1/4 25/32 1-7/8 147.00

7/8 5-1/2 4-1/4 4-1/4 2-1/4 1-3/8 15/16 2-1/8 175.00

1 6-1/8 4-15/16 4-1/2 2-1/2 1-9/16 1-1/16 2-3/8 275.00

1-1/8-1-1/4 7 5-7/8 5-1/8 2-7/8 1-7/8 1-5/16 2-3/4 400.00

1-1/4-1-3/8 9-1/16 6-13/16 6-1/2 3-1/2 2-1/4 1-7/16 3-1/4 817.00

1-3/8-1-1/2 9 7-1/8 6-1/4 3-1/2 2-5/8 1-9/16 3-3/8 1175.00

1-5/8 11-1/4 8-1/8 8 4 2-3/4 1-23/32 3-7/8 1700.00

1-3/4 12-13/16 8-1/2 9 4-1/2 2-7/8 1-27/32 4-3/8 1775.00

1-7/8-2 15-1/8 10-3/8 12 6 3-1/8 2-3/32 5-7/8 2500.00

2-1/4 17-1/8 11-7/8 14 7 3-5/8 2-3/8 6-7/8 3950.00

2-1/2 17-1/2 13-1/2 15-3/4 8-1/2 4-1/4 2-5/8 8-1/4 5000.00

DIMENSIONS IN INCHES

Stainless Steel HEAVY DUTY

TYPE 304 • ROLLED NOT FORGED

WIRE ROPE WEIGHT

DIA. SIZE per 100 in Inches in Lbs.

1/8 Lt. Duty 2.5

3/16 Lt. Duty 2.5

1/4 8.3

5/16 10.9

3/8 25.1

1/2 49.5

5/8 73

3/4 130

7/8 175

1 275

This product was compiled by:

TSgt Russell C. Wells se ll W ell s

ADSCO LINE PRODUCTS 03/02Please call for pricing.

Forged Dimensions in inches Weights in pounds

*1/8 only is supplied with reg.

Hex nut and zinc plated U-bolt.

How to attach drop Forged wire rope clips

The right way to attach wire rope clips is illustrated at left. The base of saddle should bear on the live end of the rope- U-bolt on the short or dead end. Staggering or reversing the clips does NOT give additional holding power.

1. ATTACH FIRST CLIP one base width from dead end of rope. Tighten nuts securely.

2. ATTACH SECOND CLIP as close to loop as possible. Tighten nuts firmly but not completely tight.

3. ATTACH ALL OTHER CLIPS (if required) equally spaced between the first two. Tighten nuts firmly.

CAUTION

Apply the initial load to the rope. Alternately and uniformly retighten all nuts securely, to compensate for any reduction of rope diameter. Inspect and periodically retighten. The number of clips shown should be used for 6 v 19 or 6 x 37 class, fiber core or IWRC, IPS or XIPS, right regular or long lay Wire Rope, and 8 x 19 or 8 x 7 class, fibre core, IPS or XIPS, Wire Rope.

For 6 x 19 Seale construction or similar large outer wire constructions, add one extra clip for sizes 1” and larger. Where service conditions are unusually severe, or for other classes of rope not mentioned above, add one additional clip.

Drop Forged Wire Rope Clips, when properly applied to new rope will develop high efficiencies (approximately 80%) based upon the catalog breaking strength of the wire rope. Failure to follow the above instructions will cause a reduction in efficiency.

Please include stock number and size when ordering.

• All clips are supplied with cold-forged double chamfered, heavy hex, UNC-2B nuts. *

• Meet Federal Specification FF-C-450c Type I, Class 1.

• Base, U-bolt and nuts are hot-dip galvanized in accordance with ASTM Specification A-153. *

• Forged wire rope clips are not designed for load carrying purposes therefore, working load limits have not been established.

MIN. NO. Min.

Size for Clips for Spacing Appx. Wt.

HOW TO ROPE Max between per 100

ORDER DIA. A B C D E F G H Strength Clips Pcs.

1/8 1/2 1 7/16 3/4 15/16 7/32 27/32 7/16 2 3/4 6.0

To order 3/16 19/32 1-3/32 5/8 31/32 1-3/16 1/4 15/16 1/2 2 1-1/8 9.0

1/4 11/16 1-7/16 7/8 1-7/32 1-1/2 5/16 1-1/8 11/16 2 1-1/2 18.0 use the 5/16 7/8 1-11/16 1 1-5/8 1-31/32 3/8 1-5/16 3/4 2 1-7/8 30.0

3/8 1 1-15/16 7/8 1-5/8 2 7/16 1-1/2 7/8 2 2-1/4 44.5

Prefix 1/2 1-3/16 2-1/4 1-1/16 1-29/32 2-5/16 1/2 1-13/16 1-3/32 3 3 71.6

5/8 1-1/4 2-3/8 1-7/16 2-3/8 2-7/8 9/16 2-1/16 1-1/4 3 3-3/4 100.0

WRC 3/4 1-1/2 2-3/4 1-1/2 2-13/16 3-3/8 5/8 2-5/16 1-15/32 4 4-1/2 140.0

size 7/8 1-3/4 3-3/16 1-7/8 3-1/8 3-7/8 3/4 2-7/16 1-1/2 4 5-1/4 200.0 follow ed 1 1-7/8 3-1/2 2-1/4 3-1/2 4-1/4 3/4 2-11/16 1-3/4 5 6 245.0

1-1/8 2-1/16 3-11/16 2-3/16 3-7/8 4-5/8 3/4 3 2 6 6-3/4 285.0 by FGD. 1-1/4 2-3/16 4-1/16 2-3/8 4-1/4 5-1/8 7/8 3-1/4 2-5/32 6 7-1/2 415.0

1-1/2 2-19/32 4-1/2 2-7/16 5 5-7/8 7/8 3-3/8 2-13/32 7 9 543.0

DIMENSIONS

This product was compiled by:

TSgt Russell C. Wells se ll W ell s

ADSCO LINE PRODUCTS 03/02 Please call for pricing.

Malleable / Zinc Plated or Self Colored Dimensions in inches/Weights in pounds

• All regular hex nuts.

• Clips meet FF-C-450 Type I Class 2

• Bulk pack

• Wire rope clips are not designed for load carrying purposes therefore, Working Load Limits have not been established.

USE CLIPS PROPERLY FOR MAXIMUM EFFICIENCY

1. U-Bolt should bear on dead end of rope.

2. Recommended number of clips, depending on safety requirement:

3. Spacing between clips should be 6 times the rope diameter.

4. Nuts should be re-tightened after initial load.

Zinc plated will be supplied unless otherwise specified.

SELF-COLORED ZINC-PLATED

RECOMMENDED

SIZE NUMBER OF CLIPS

1/16 to 3/8 2-4 7/16 to 5/8 3-4

3/4 to 1 4-5 1-1/8 to 1-1/4 6-8

HOW TO ROPE APPX. WT.

ORDER SIZE PER 100 PCS.

* 1/16 3.0

* 1/8 4.5 3/16 6.5

To order 1/4 12.0 5/16 12.0 use the 3/8 19.0 7/16 21.8

Prefix: 1/2 37.0 9/16 46.0

WRC-Size 5/8 54.0 3/4 80.0 followed 7/8 116.0 1 137.0 by MAL. 1-1/8 267.0 1-1/4 328.0

HOW TO ROPE APPX. WT.

ORDER SIZE PER 100 PCS.

* 1/16 3.0

To order * 1/8 4.5 3/16 6.5 use the 1/4 12.0 5/16 12.0

Prefix: 3/8 19.0 7/16 21.8

WRC-Size 1/2 37.0 9/16 46.0 followed 5/8 54.0 3/4 80.0 by ZP. 7/8 116.0 example: 1 137.0

WRC-1/2ZP 1-1/8 267.0

1-1/4 328.0

*NOTE: Not covered by FF-C-450 Type 1 Class 2

This product was compiled by:

TSgt Russell C. Wells se ll W ell s

ADSCO LINE PRODUCTS 03/02 Please call for pricing.

WIRE ROPE WEIGHT

DIA. SIZE EACH

in Inches A B C D E F in Lbs.

1/8 1-15/16 1-1/16 1-5/16 11/16 5/32 5/8 3.3

3/16 1-15/16 1-1/16 1-5/16 11/16 7/32 5/8 3.3

1/4 1-15/16 1-1/16 1-5/16 11/16 9/32 5/8 3.3

5/16 2-1/8 1-1/4 1-1/2 13/16 3/8 3/4 4

3/8 2-3/8 1-15/32 1-5/8 15/16 7/16 7/8 7.50

1/2 2-3/4 1-3/4 1-7/8 1-1/8 9/16 1-1/16 18.80

5/8 3-1/2 2-3/8 2-1/4 1-3/8 11/16 1-1/4 36.

3/4 3-3/4 2-11/16 2-1/2 1-5/8 13/16 1-1/2 60.

7/8 5 3-3/16 3-1/2 1-7/8 15/16 1-3/4 90.

1 5-11/16 3-3/4 4-1/4 2-1/2 1-1/16 2-3/8 105.

1-1/8-1-1/4 6-1/4 4-5/16 4-1/2 2-3/4 1-5/16 2-5/8 166.

1-1/2 7-1/2 5-3/8 5 3-1/4 1-9/16 3-1/8 325.

1-3/4 10-3/4 7-1/4 7-1/4 4-1/4 1-7/8 4-1/8 583.25

2 10-3/4 7-1/4 7-1/4 4-1/4 2-1/8 4-1/8 583.25

DIMENSIONS IN INCHES

Wire Rope Thimbles Stainless Steel

HEAVY DUTY

STANDARD

PER FED. SPEC. FF-T-276B, TYPE III • ALSO AVAILABLE WITH WELDED GUSSET

WELDED GUSSET PLATES AVAILABLE FOR GUSSET 2”, 2 1/4”, AND 2 1/2”

MEETS FEDERAL SPECIFICATIONS FF-T-276B, TYPE II

WIRE ROPE MAX. PIN WEIGHT

DIA. SIZE DIA. per 100 in Inches A B C D E F in Inches in Lbs.

1/4 2-3/16 1-1/2 1-5/8 7/8 13/32 9/32 13/16 6.5

5/16 2-1/2 1-13/16 1-7/8 1-1/16 1/2 11/32 15/16 11.25

3/8 2-7/8 2-1/8 2-1/8 1-1/8 21/32 13/32 1-1/16 25.00

7/16 3-1/4 2-3/8 2-3/8 1-1/4 3/4 15/32 1-3/16 50.00

1/2 3-5/8 2-3/4 2-3/4 1-1/2 27/32 17/32 1-7/16 51.00

9/16 3-5/8 2-11/16 2-3/4 1-1/2 29/32 19/32 1-7/16 51.00

5/8 4-1/4 3-1/8 3-1/4 1-3/4 1 21/32 1-5/8 75.00

3/4 5 3-3/16 3-3/4 2 1-1/4 25/32 1-7/8 147.00

7/8 5-1/2 4-1/4 4-1/4 2-1/4 1-3/8 15/16 2-1/8 175.00

1 6-1/8 4-15/16 4-1/2 2-1/2 1-9/16 1-1/16 2-3/8 275.00

1-1/8-1-1/4 7 5-7/8 5-1/8 2-7/8 1-7/8 1-5/16 2-3/4 400.00

1-1/4-1-3/8 9-1/16 6-13/16 6-1/2 3-1/2 2-1/4 1-7/16 3-1/4 817.00

1-3/8-1-1/2 9 7-1/8 6-1/4 3-1/2 2-5/8 1-9/16 3-3/8 1175.00

1-5/8 11-1/4 8-1/8 8 4 2-3/4 1-23/32 3-7/8 1700.00

1-3/4 12-13/16 8-1/2 9 4-1/2 2-7/8 1-27/32 4-3/8 1775.00

1-7/8-2 15-1/8 10-3/8 12 6 3-1/8 2-3/32 5-7/8 2500.00

2-1/4 17-1/8 11-7/8 14 7 3-5/8 2-3/8 6-7/8 3950.00

2-1/2 17-1/2 13-1/2 15-3/4 8-1/2 4-1/4 2-5/8 8-1/4 5000.00

DIMENSIONS IN INCHES

Stainless Steel HEAVY DUTY

TYPE 304 • ROLLED NOT FORGED

WIRE ROPE WEIGHT

DIA. SIZE per 100 in Inches in Lbs.

1/8 Lt. Duty 2.5

3/16 Lt. Duty 2.5

1/4 8.3

5/16 10.9

3/8 25.1

1/2 49.5

5/8 73

3/4 130

7/8 175

1 275

This product was compiled by:

TSgt Russell C. Wells

Fused Cutout / Lightning Arrester Specifications

Information compiled by: TSgt Russell Wells se ll W ell s

Type ICX Interchangeable Cutout

15-38 kV Outdoor Distribution Cutout Product Bulletin 1VAG271201-DB se ll W ell s

Product Features

• 15, 27, or 38 kV

• 110, 125, 150, 180, or 200 kV BIL

• 100 A, 200 A Fused

• 300 A Disconnect Blade

• Porcelain, Silicone, or Polymer Concrete Insulators Available

• Seacoast Design

• ECD (Emission Control Device)

• Cutout/Arrester Combo

• Kick-out Spring

Description The ABB ICX interchangeable cutout is used on overhead distribution systems to provide overcurrent protection and visible indication of fuse operation. The ICX provides a visible break sectionalizing point for maintenance personnel and is equipped with hooks to use with a portable loadbreak tool. This allows the ICX to be used as a loadbreak switch to open the circuit with load current flowing.

Silicone or Polymer Concrete insulators, Emission Control Devices (ECDs), Seacoast design, cutout/arrester combinations, and Autolink options are available on certain models.

Ratings The ICX cutout is offered in three frame sizes and five BIL ratings.

Each of the frames accommodates fuseholders with various ratings.

ICX ratings are 110 kV through 200 kV BIL.

Design Features The ICX 100 A fuse is provided with a moisture proof tube as a stan-dard offering. Cutouts perform by expelling gases during interruption from the bottom of the fuse tube. For the highest interrupting rating, a link extender rod is attached to the fuse tube cap, improving the effi-ciency of gas expulsion and arc interruption. Fuse tubes with more than one rating are clearly labeled to indicate each interrupting capability.

This minimizes the number of styles that must be stocked, while pro-viding the broadest range of application flexibility.

Interchangeability The ICX cutout is designed to be electrically and mechanically inter-changeable with the S&C type “XS”, A.B. Chance type “C”, and Cooper type “L” cutouts. Fuseholder caps are also interchangeable with the S&C design. Testing has confirmed the performance of the ICX fuse-holder and fuse support with S&C and Chance.

Standards and Design Testing The ICX cutout meets or exceeds all applicable requirements of EEI, NEMA SG-2-1986, and ANSI C37.41.1994 and C37.42-1989 standards.

- 2 -

ICX with ECD

ICX with arrester combination

15 kV ICX polymer concrete se ll W ell s

Silicone Rubber Silicone rubber has been used for more than 25 years as an outdoor insulation material and has become the fastest growing choice for polymeric material for medium and high voltage outdoor insulation. Silicone was selected for its superior performance, durability, and insulation properties.

It has the unique ability to maintain its hydrophobicity and offers greater stability against heat and ultraviolet radiation compared to other polymers. In addition, silicone cutouts are 30% - 50% lighter than porcelain units. Silicone insula-tors are available in all ratings up to 180 kV BIL.

Polymer Concrete ABB has been using polymer concrete for more than 10 years. It is available in the 110 and 125 kV BIL ratings.

Polymer concrete provides a safe, shatter-proof design with molded-in rods to prevent moisture penetration. Polymer concrete is cold weather friendly since it resists damage from freeze/thaw cycles. This makes it an excellent replacement for porcelain in colder climates. It is a field-proven material that provides excellent electrical properties and dielectric strengths, as well as superior mechanical durability.

ICX with ECD The ICX is available with an Emission Control Device (ECD). The ECD prevents forest fires and provides added operator and environment protection. The unlatching oper-ation of the dropout is unique in the ECD, as it automati-cally resets to the service position upon closing the dropout carrier.

Kick-out Spring All ICX fuse tubes are available with an optional kick-out spring. The spring assists the drop-out operation by increas-ing the kick-out force on the tube.

Fuse Tube Construction The ICX cutouts utilize two different types of fuse tubes: a moisture-proof fuse tube or a high-strength glass fuse tube.

The moisture proof fuse tube is standard on all 100 A designs and is notated by the letter "M" in the 8th digit of the style number (refer to Ordering Instructions on pages 6-7). The moisture-proof tube reduces swelling that can create problems with interruption.

The 200 A design utilizes a high-strength glass fuse tube and is notated by the letter "A" in the 8th digit of the style number (refer to Ordering Instructions on pages 6-7). This fuse tube is composed of a horn fiber liner surrounded by a glass filament wound outer shell. The durable tube with-stands the rigors of high fault current interruptions. In addition, the tube is applied with electrostatic powder paint to provide protection against the effects of ultraviolet rays.

Voltage Levels Single voltage rated cutouts can be applied on any single or three-phase system where the line-to-line voltage does not exceed the cutout rating. Dual voltage rated cutouts are suit-able on single-phase circuits where maximum line-to-ground voltage does not exceed the value shown to the left of the slash (for example, does not exceed 7.8kV in 7.8/15kV).

ICX cutouts may be used on three-phase circuits that are solidly grounded and the maximum line-to-line voltage does not exceed the value shown to the right of the slash (for example, does not exceed 27kV in 15/27 kV).

Each frame size has fault interrupting ratings at more than one voltage level. An extensive testing program was per-formed to develop these multi-voltage capabilities. As a result of this program, the voltage rating of some ICX cutouts may be increased by changing the fuseholder.

Options

27 kV Silicone ICX with 300 A blade (600 mm creep)

15 kV Silicone ICX

- 3 -

Construction Details

27 kV ICX with Autolink

27 kV Silicone ICX (180 kV BIL)

FA461019RA029 - ATTACHMENT 07

user Highlight se ll W ell s

- 4 -

Unit Dimensions kV Class

BIL

(kV)

Unit Dimensions (in) Creep* (in)

Weight* (lb)A B C D E FR

15 110 12.79 7.33 6.50 8.55 6.60 11.41 9.1 14.0

27 125 13.30 7.84 8.17 10.25 6.08 14.88 12.8 20.0

27 or 38 150 13.30 7.84 8.17 10.25 6.08 14.88 17.0 26.5

27 or 38 170 13.96 8.51 10.42 13.00 5.27 19.21 26.2 35.5 kV Class

BIL

(kV)

Unit Dimensions (mm) Creep* (mm)

Weight* (kg)A B C D E FR

15 110 325 186 165 217 168 290 231 6.4

27 125 338 199 208 260 154 378 325 9.0

27 or 38 150 338 199 208 260 154 378 432 12.0

27 or 38 170 356 216 265 330 134 488 665 16.1

A

FR

E

1.00 [25]

D

17-20 DEG

1.56 [40]

4.12-5.12 [105-130]

7.75 [197]

3.0-4.0 [76-102]

2.25 [57]

B

.312 NEMA "A" BRKT

.375 NEMA "B" BRKT

C

Note: Metric dimensions are displayed in [mm].

* Creep and weight values are for standard porcelain units.

se ll W ell s

- 5 -

Bracket Dimensions

Note: Metric dimensions are displayed in [mm].

.38 [10]

7.8 [198]

1.5 [38]

5.4 [137]

Extended bracket

NEMA A bracket NEMA B bracket

Pole Mounting bracket

.312 [8]

7.8 [198]

1.6 [40]

2.6 [67]

.375 [10]

7.8 [198]

1.6 [40]

2.6 [67]

12.8 [325]

6.9 [175]

2.2 [56]

9.1 [231]

Part numbers listed on page 8.

se ll W ell s

- 6 -

X

DIGIT 3

Fuse Support

N = Porcelain

J = Silicone

Z = Polymer concrete

S = Seacoast design porcelain

E = Emission control porcelain

DIGIT 5

Bracket

N = No bracket

A = NEMA A

B = NEMA B

L = Extended

U = Pole Mounting

DIGIT 4

Terminal Connectors

N = No terminal

C = Clamshell

E = Eyebolt

DIGIT 6

Special Options

N = None

F = Wildlife guard

Y = Combo box

DIGIT 11

Additional Options

K = Kick-out spring on fuse tube

S = Seacoast design silicone

DIGITS 7-10

Fuseholder

AM11 = 100A, 10kAIC, Solid cap

LM11 = 100A, 16kAIC, Link extender

KA21 = 200A, 12kAIC, Link extender

PA21 = 200A, 10kAIC, Link extender

CA31 = 300A, Solid blade (rated 7.8/15 kV)

DIGIT 2

Insulator BIL

1 = 110 kV BIL

ICX 15 kV

ICX 27 kV

X

DIGIT 3

Fuse Support

N = Porcelain

J = Silicone

Z = Polymer concrete

S = Seacoast design porcelain

E = Emission control porcelain

DIGIT 5

Bracket

N = No bracket

A = NEMA A

B = NEMA B

L = Extended

U = Pole Mounting

DIGIT 4

Terminal Connectors

N = No terminal

C = Clamshell

E = Eyebolt

DIGIT 6

Special Options

N = None

F = Wildlife guard

Y = Combo box

DIGIT 11

Additional Options

K = Kick-out spring on fuse tube

S = Seacoast design silicone

DIGITS 7-10

Fuseholder

AM12 = 100A, 8kAIC, Solid cap

GM12 = 100A, 12kAIC, Link extender

MM12 = 100A, 12kAIC, Link extender

WA22 = 200A, 12kAIC, Link extender

DA32 = 300A, Solid blade

(rated 15/27 kV)

VA22 = 200A, 12kAIC, Link extender

DIGIT 2

Insulator BIL

2 = 125 kV BIL

4 = 150 kV BIL 600 mm creep

(silicone only)

8 = 180 kV BIL 750 mm creep

9 = 200 kV BIL 1130 mm creep

5 = 150 kV BIL

(silicone only)

(silicone only)

(125 kV BIL only)

Ordering Instructions

FA461019RA029 - ATTACHMENT 07

user Highlight user Highlight user Highlight user Highlight user Highlight user Highlight user Highlight user Highlight user Highlight se ll W ell s

- 7 -

X

DIGIT 3

Fuse Supports

N = Porcelain

J = Silicone

S = Seacoast design porcelain

E = Emission control porcelain

DIGIT 5

Bracket

N = No bracket

A = NEMA A

B = NEMA B

L = Extended

U = Pole Mounting

DIGIT 4

Terminal Connectors

N = No terminal

C = Clamshell

E = Eyebolt

DIGIT 6

Special Options

N = None

F = Wildlife guard

Y = Combo box

DIGIT 11

Additional Options

K = Kick-out spring on fuse tube

S = Seacoast design silicone

DIGITS 7-10

Fuseholder

TA12 = 100A, 10kAIC, Link extender

DA32 = 300A, Solid blade

DIGIT 2

Insulator BIL

4 = 150 kV BIL 600mm creep (silicone only)

5 = 150 kV BIL

8 = 180 kV BIL 750mm creep (silicone only)

ICX 38 kV, 150 or 180 kV BIL

ICX 38 kV, 170 kV BIL

X

DIGIT 3

Fuse Supports

N = Porcelain

S = Seacoast design porcelain

DIGIT 5

Bracket

N = No bracket

A = NEMA A

B = NEMA B

L = Extended

U = Pole Mounting

DIGIT 4

Terminal Connectors

N = No terminal

C = Clamshell

E = Eyebolt

DIGIT 6

Special Options

N = None

F = Wildlife guard

Y = Combo box

DIGIT 11

Additional Options

K = Kick-out spring on fuse tube

S = Seacoast design silicone

DIGIT 2

Insulator BIL

7 = 170 kV BIL

DIGITS 7-10

Fuseholder

RA15 = 100A, 10kAIC, Link extender

FA34 = 300A, Solid blade

RA14 = 100A, 12kAIC, Link extender

SA24 = 200A, 10kAIC, Link extender (tube rated for 15/27 kV)

(tube rated for 27 kV) se ll W ell s

V

A G

-D

B R e v

B M a y re p la c e s

-6

C o p y ri g h t

A

B B

A ll ri g h ts r e s e rv e d

ABB Inc.

406 Banner Ave.

Greensboro, NC 27401 Tel: +1-336-275-7310 www.abb.com/mediumvoltage

Style Number

Voltage Rating

(kV)

BIL

(kV)

Current Rating

(A)

Interrupting Rating (kAIC) Cap Type

Corresponding Cutout*

7194C60G01MP 15 110 100 10 Solid AM11

7194C60G02MP 15 110 100 16 Link Extender LM11

7194C60G03 7.8/15 110 200 12 Link Extender PA21

7194C60G04 15 110 300 - Solid Disconnect Blade CA31

7194C60G05MP 27 125 or 150 100 8 Solid AM12

7194C60G06MP 27 125 or 150 100 12 Link Extender MM12

7194C60G07 15/27 125 or 150 200 10 Solid BA22

7194C60G08 27 125 or 150 300 - Solid Disconnect Blade DA32

7194C60G08 38 150 300 - Solid Disconnect Blade DA32

7194C60G11MP 27 170 100 12 Link Extender MM13

7194C60G12MP 38 170 300 - Solid Disconnect Blade EA33

7194C60G19 15 110 200 10 Link Extender KA21

7194C60G26 27 125 or 150 200 12 Link Extender VA22

Style Number

Voltage Rating

(kV)

BIL

(kV)

Current Rating

(A)

Interrupting Rating (kAIC) Cap Type

3A31186H01 15 110 100 10 Solid Cap

9861A62G05 15 110 100 16 Link Extender

9861A62G08 7.8/15 110 200 12 Link Extender

3A31187H01 15/27 125 or 150 200 10 Solid Cap

3A31186H01 27 125 or 150 100 8 Solid Cap

9861A62G06 27 125 or 150 100 12 Link Extender

9861A62G07 27 170 100 12 Link Extender

* Used with ICX cutouts having the following characters in digit positions 7-10 of the ABB cutout style number.

Optional Cutout Parts

Replacement Fuseholders

Replacement Fuseholder Caps

Brackets

Style Number Type

367C723G05 NEMA A

403A101G03 NEMA B

367C802G05 Extended

791C890G16 Pole Mounting

JUNE 2006

31-1

OHIO BRASS – AIKEN, SC

POWER SYSTEMS, INC.

Printed in USA

Section

IEEE C62.11 TESTED

DynaVar ® Distribution Class (PDV) and

Riser Pole (PVR) Surge Arresters

Introducing the NEW PDV-100 OPTIMA U.S. Patent Numbers: 6,828,895

& 6,956,458