J09 Appendix B Maintenance Inspection Requirement.docx
DOCX document 24 KB Posted
- Attached to
- ManliftS MX
- Solicitation number
- FA448426R0003
About this file
This is an appendix to a federal contract solicitation that outlines maintenance inspection requirements for manlifts governed by American National Standards Institute (ANSI) standards ANSI a92.5-1992 and ANSI a92.5-2006. The inspection procedures must be performed every three months or 150 hours, whichever comes first, or more frequently based on environmental conditions and usage severity. Inspections are also required following any maintenance performed on the equipment.
The inspection requirements cover multiple system components including chassis elements (tires, wheel assemblies, axles, drive hubs, motors, brakes, hydraulic lines, electrical connections, and batteries), turntable components (lift cylinders, drive motors, swing bearings, valves, and ground controls), and boom systems (pivot bushings, lift cylinders, leveling links, uprights, telescope cylinders, and platform leveling components). Each inspection area specifies checks for damage, wear, lubrication, proper meshing, leakage, security of fasteners and connections, corrosion evidence, and proper fluid levels, with replacement of hydraulic filter elements at recommended intervals. These detailed inspection requirements support compliance with American National Standard Boom-Supported Elevating Work Platforms and Occupational Safety and Health standards as mandated under solicitation FA448426R0003 for the Department of the Air Force Air Mobility Command.
View the file
Other files
Show all 23
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
Maintenance Inspection Governed by American National Standards Institute (ANSI) ANSI a92.5-1992 AND ANSI a92.5-2006 Note: ANSI/SIA 92.5-1992 also requires an annual inspection to be performed. See annual machine inspection report CGF330.
A systematic inspection to assist in detecting defective, damaged, or improperly installed parts. The inspection shall be performed every 3 months or 150 hours whichever comes first, or more often when required by environment, severity, and frequency of usage. This inspection is also to be performed after maintenance has been performed on the machine.
Chassis:
Check front and rear tires and wheel assemblies for loose or worn spindles, components and hardware for security, tires for wear, damage and proper inflation.
Check front and rear axle for loose, missing and worn parts, pivot pin for security.
Check drive hubs for damage and leaks, and motors and brakes for damage.
Check oil level in drive hubs for proper levels, add as required.
Check valves and hydraulic lines for damage, leakage and security.
Check pump/motor and accessories for damage, loose or missing parts, leakage and security.
Check electrical connections for corrosion and tightness and wiring for insulation damage. Check hydraulic filters for condition of element and replace as required.
Check batteries for damage, loose or missing vent caps, electrical connections for tightness and evidence of corrosion, and proper electrolyte level, add as required.
Turntable Check turntable of damage, loose or missing parts, and security. Check lift cylinders and hydraulic lines for damage, leakage and security. Check drive motors for damage, loose or missing parts, hydraulic lines and component housings for evidence of leakage. Check worm gear for the proper meshing with swing gear.
Check swing bearing for damage, wear, lubrication and loose or missing bearing bolts.
Check valves and hydraulic lines for damage, leakage, security and electrical connections for tightness and evidence of corrosion.
Check ground controls for damage, loose or missing parts, security, electrical connection for tightness and evidence of corrosion and wiring for insulation damage. Check all switches for proper function.
Replace hydraulic filter elements at recommended intervals.
Check all cowl and access doors for damage, proper operation and security.
Check all boom pivot bushings for lubrication and wear.
Check lower boom lift cylinder and hydraulic lines for damage, security and leakage.
Check all pin and shaft retaining hardware for security and wear.
Check all electrical cables for damage, loose and corroded connections.
Check lower boom and leveling link for damage, missing parts and security.
Check all min and shaft retaining hardware for security and wear.
Check limit switch connections and plunger for corrosion and security.
Check limit switch connections and plunger for corrosion and security.
Check upright for damage, wear, lubrication, and security.
Check upper boom lift cylinder an cross pins and hydraulic lines for damage, wear, lubrication, and leakage and security.
Check upper boom for damage, missing parts and security.
Check hydraulic lines mounted on the upright for damage, leakage and security.
Check upper boom pads for damage, missing parts and security.
Check upper boom telescope cylinder, cross pins and hydraulic lines for damage, wear, lubrication, leakage and security.
Check platform leveling cylinder, cross pins and hydraulic lines for damage, wear, lubrication, leakage and security.
File details come from the government source that posted it. Updated .