FC61 - Paint Schedule.pdf

VT Halter Marine, Inc.VT Halter Marine, Inc.

AMERON PERFORMANCE COATINGS AND FINISHES GROUP

PAGE 10F34

STEEL

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

KEEL TO LOWER EDGE OF DEEP LOAD LINE SPOT BLAST DA..\1AGED AREA TO NEAR WHITE SSPC.SP.IO. SANDSWEEP ALL REMAlNlNG

INCLUDING CENTERBOARD TRUNK AREA TO SSPC.SP7.

INTERIOR BELOW WATERLINE, RUBBER,

OTIffiR APPENDAGES BELOW DEEP LOAD

LINE

SPREAD RATE @ SPEC. Overcoat Time Application Method SYSTEM INFORMATION COLOR TYPE WFT DFT DFT Sq.Ft. per Gal at 70F Aidess Spray

COAT MILS MILS Conv. AirIess Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

AMERCOAT 385 RED FULL 8.0 5.0 212 148 8 hrs 6 X .21 mos

AMERCOAT 385 GRAY FULL 8.0 5.0 212 148 8 hrs 24 X .21 --.. ----------------------------------- hrs

ABC #4 RED FULL 8.0 5.0 189 132 8hrs 30 X .21 days

I ABC #4 BLACK FULL 8.0 5.0 189 132 8hrs X .21

Solid Curing Mixed Pot Dry at 70F Flash Thinner (1) Application (2) Ventilation Product Information Volume Agent Ratio Life Point TempF Humidity Cu.Ft./Gal

Ratio Base:Cure deg.F

Handle Hard Min Max Min Max 385 66 385 1 TO I 4 hrs 4 hrs 8hrs 120° 65 32° 120° 85%

ABC #4 59 N/A N/A N/A 4 hrs 6 hrs 82° 65 40° 100° 85%

(1) Not more than __ % by volume.

Remarks: (2) No coating to be applied when substrate is within SF of dewpoint.

HULL MARKINGS WITH AMERCOAT 229C WHITE AT 2.0 MILS

STEEL PAGE20F34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

SEA CHESTS & HIGH TURBULANCE AREAS SPOT BLAST TO SP-lO & SANDSWEEP ALL REMAINING AREA TO REMOVE ALL

CONTAMINATION.

SPRFAD RATE @ SPEC. Overcoat Time Application Method SYSTEM INFORMATION COLOR TYPE WFT DFT DFT Sq.Ft. per Gal at 70F Airless Spray

COAT MILS MILS Conv. Airless Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

AMERCOAT 385 RED FULL 8.0 5.0 212 148 8 hrs 6 X .21 mos

AMERCOAT 385 BLACK FULL 8.0 5.0 212 148 8hrs 24 X .21 ~*~~W8~~~~ ______ _ ___________ • __ hrs AMERLOCK 400 GFK RED FULL 6.0 5.0 266 186 8 hrs 24 X .. 55 hrs

AMERLOCK 400 GFK BLACK FULL 6.0 5.0 266 186 NIA X

Solid Curing Mixed Pot Dry at 70F Flash Thinner (1) Application (2) Ventilation Product Information Volume Agent Ratio Life Point TempF Humidity Cu.Ft./Gal

Ratio Base:Cure deg. F

Handle Hard Min Max Min Max 66 385 1 TO 1 4 hrs 4 hrs 8 hrs 120" 65 32" 120" 85%

385 .

83 400 3 PART 4 hrs 8hrs 12 hrs 131" 65 32" 90" 85%

400GFK

(3) Not more than __ % by volume.

Remarks: (4) No coating to be applied when substrate is within 5F of dewpoint.

STEEL PAGE30F34

COATINGS SPECIFICATION OWNER: JOB:

I SURFACE PREPARATION: AREA:

DEEP LOAD LINE TO RAIL AND OUTBOARD SPOT BLAST TO SP.IO AND SANTISWEEP ALL REMAINING AREA TO REMOVE ALL

SIDE OF BULWARKS CONTAMINATION.

SPREAD RATE @ SPEC. Overcoat Time Application Method SYSTEM INFOR;\1A TION COLOR TYPE WFT DFT DFT Sq.Ft. per Gal at 70F Airless Spray

COAT MILS MILS Cony. Airless Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

DIMETCOTE 302H GREEN FULL 4.0 3.0 417 292 4 hrs IND. X .21 I

AMEROCAT 385 RED FULL 8.0 5.0 212 148 8 hrs 72 X .21 hrs

AMERCOAT 229T WHITE FULL 4.0 2.0 361 253 N/A X .21

Solid Curing Mixed Pot Dry at 70F Flash Thinner (1) Application (2) Ventilation Product Infonnation Volume Agent Ratio Life Point TempF Humidity Cu. FUGal

Ratio Base: Cure deg. F

Handle Hard Min Max Min Max 302H 78 PWD I TO 1 4 hrs 1 hrs 4 hrs lIO° +·10 32° 90° 85%

385 66 385 I TO I 4 hrs 4 hrs 8 hrs 120° 65 32' 120° 85%

229T 45 229 4 TO 1 4hrs 4 hrs 8 hrs 105° 911 32° 90 0 85%

Remarks:

HULL MARKINGS 229T: BLACK 2.0 MILS D.F.T.

LIGmBLUE 2.0 MILS D.F.T.

DARK BLUE 2.0 MILS D.F.T.

STEEL PAGE40F34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

SPOT BLAT TO SP,l O AND SANDSW EEP ALL REMAINING AREA TO REMOVE ALL

CONTAMINATION.

SPREAD RATE @ SPEC. Overcoat Time Application. Method SYSTEM INFORMATION COLOR TYPE WFT DFT DFT Sq.Ft. per Gal at 70F Airless Spray

COAT MILS MILS Conv. Airless Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

DIMETCOTE 302H GREEN FULL 4.0 3.0 417 292 4 hrs IND. X .21

AMEROCAT 385 RED FULL 8.0 5.0 212 148 8 hrs 72 X .21 hrs

AMERCOAT 229T WHITE FULL 4.0 2.0 361 253 N/A X .21

Solid Curing Mixed Pot Dry at 70F Flash Thinner (1) Application (2) Ventilation ProducllnforIl1ation Volume Agent Ratio Life Point TempF Humidity CuR/Gal

Ratio Base:Cnre deg.F

Handle Hard Min Max Min Max 302H 78 PWD 1 TO 1 4 hrs I hrs 4 hrs 1100 +·10 32° 90° 85%

385 66 385 1 TO J 4hrs 4 hrs 8 hrs 1200 65 320 120° 85%

229T 45 229 4TO I 4 hrs 4 hrs 8 hrs 105 0 911 32° 90° 85%

(5) Not more than _ _ % by volume.

AREA: EXTERIOR STEEL SIS, DECKHOUSES, VENTS, OVERFLOWS, OVERHEAD, (6) No coating to be applied when substrate is within 5F of dewpoint.

SURF ACES. DECK GEAR LOCKERS. DOORS. STANCHIONS. EXTERIOR VERTICAL

AND INCLINED LADDERS. HANDRAILS, BREAKWATERS, VENTILATORS, STACK,

BUL W ARK MOUNTED CHOCKS, DAVITS AND RAILS.

STEEL PAGE 5 OF 34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

ALL EXTERIOR DECKS (6" UP ON VERT. SPOT BLAST TO SP-I0 SANDS WEEP ALL REMA1NING AREA TO REMOVE ALL

SURFACE) HOUSE TOPS TRAWLWAY, TRAWL CONTAMINATION.

RAMP: ETC (CONTINUED 1N REMARKS)

SPREAD RATE @ SPEC. Overcoat Time Application Method SYSTEM INFORMATION COLOR TYPE WIT DIT DIT Sq.Ft. per Gal at 70F Airiess Spray

COAT MILS MILS Conv. Airless Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

DIMETCOTE 302H GREEN FULL 4.0 3.0 417 292 4hrs IND. X .21

AMEROCAT 385 RED FULL 8.0 5.0 212 148 8 hrs IND X .21

AMERCOAT 385 DARK FULL 80 5.0 212 148 N/A X .21

WITH N/S #888 GRAY

Solid Curing Mixed Pot Dry at 70F Flash Thiuner (1) Application (2) VenWatioll Product Information Volwne Agent Ratio Life Point TempF Humidity Cu,FUGaI

, Ratio Base:Cure deg, F

Handle Hard Min Max Min Max 302H 78 PWD 1 TO 1 4 hrs 1 hrs 4 hrs 1100 +- 10 320 900 85%

385 66 385 I TO 1 4 hrs 4hrs 8 hrs 1200 65 320 1200 85%

385 N/S 665 385 1 TO 1 4 hrs 4 hrs 8 hrs 1200 65 32° 1200 85%

(7) Not more than __ % by volume, Remarks: (8) No coating to be applied when substrate is within 5F of dewpoillt

NOTE - 888 NON-SKID ADDED TO FINISH COAT AS REQUIRED!

* AREA - EXTERIOR HATCH COVERS & INBOARD SIDE OF BULWARKS

STEEL PAGE 6 OF 34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

ALL EXTERIOR FOUNDATIONS, DECK SPOT BLAST TO SP-lO AND SANDSWEEP ALL REMAINlNG AREA TO REMOVE ALL

FITTINGS AND WEATHER HATCH CONTAMINATION.

COAMINGS.

SPREAD RATE @ SPEC. Overcoat Time Application Method SYSTEM INfORMATION COLOR TYPE WFT DFT DFT Sq.Ft. per Gal at 70F Airless Spray

COAT MILS MILS Conv. Airless Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

DIMETCOTE 302H GREEN FULL 4.0 3.0 417 292 4 hrs IND. X .21

AMEROCAT 385 RED FULL 8.0 5.0 212 148 8hrs IND X .21

AMERCOAT 385 DARK FULL 80 5.0 212 148 N/A X .21

GRAY

Solid Curing Mixed Pot Dry at 70F Flash Thinner (1) Application (2) Ventilation Product Information Volume Agent Ratio Life Point TempF Humidity Cu.Ft.lGaI

Ratio Base:Cure deg. F

Handle Hard Min Max Min Max 302H 78 PWD 1 TO I 4 hrs I hrs 4 hrs 110° +- 10 32° 90° 85%

385 66 385 1 TO 1 4 hrs 4 hrs 8 hrs 120° 65 32° 120° 85%

(9) Not more than __ % by volume.

Remarks: (lO)No coating to be applied when substrate is within SF of devl'point.

STEEL PAGE 70F34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

DECK MACH. ELECTRIC BRAKE, MOTOR SPOT BLAST TO SP·I0 AND SANDSWEEP ALL REMAINING AREA TO REMOVE ALL

HOUSING EXTERIOR DECK MOUNTED CONTAMINATION.

CHOCKS, ETC,

(CONTINUED IN REMARKS)

SPREAD RATE @ SPEC. Overcoat Time Application Method SYSTEM INFORMATION COLOR TYPE WFT DFT DFT Sq.Ft. per Gal at 70F Aidess Spray

COAT MILS MILS Conv. Aidess Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

DlMETCOTE 302H GREEN FULL 4.0 3.0 417 292 4 hrs IND. X .21

AIvIERCOAT 385 RED FULL 8.0 5.0 212 148 8 hrs 72 X .21 hrs

A.'v1ERCOAT 229T BLAC FULL 4.0 2.0 361 253 N/A X .21 K

Solid Curing Mixed Pot Dry at 70F Flash Thinner (1) Application (2) Ventilation Prodnct Information Volume Agent Ratio Life Point TempF Humidity Cn.Ft/Gai

Ratio Base:Cure deg. F

Handle Hard Min Max Min Max 302H 78 PWD 1 TO 1 4 hrs 1 hrs 4 hrs llOo +·10 320 900 85%

385 66 385 I TO I 4 hrs 4 hrs 8hrs 1200 65 320 1200 85%

229T 45 229 4TOI 4 hrs 4hrs 8 hrs 1050 911 320 900 85%

(II) Not more than __ % by volume.

Remarks: (12) No coating to be applied when substrate is within 5F of dewpoint

CLEATS, BITTS AND F AIRLEADS!

STEEL PAGE80F34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

MASTS, BOOMS, TRUSSES, JACK AND ENSIGN SPOT BLAST TO SP.l0 SANDSWEEP ALL REMAINING AREA TO REMOVE ALL STAFF, KlNG POSTS AND SIMILAR FITTINGS CONTAMINATION.

SPREAD RATE @ SPEC. Overcoat Time Application Method SYSTEM INFORMATION COLOR TYPE WFT DFT DFT Sq.Ft. per Gal at 70F Airless Spray

COAT MILS MILS Conv. Aidess Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

DIMETCOTE 302H GREEN FULL 4.0 3.0 417 292 4 hrs IND. X .21

AMERCOAT 385 RED FULL 8.0 5.0 212 148 8 hrs 72 X .21 hrs

AMERCOAT 229T BUFF FULL 4.0 2.0 361 253 N/A X .21

Solid Curing Mixed Pot Dry at 70F Flash Thinner (1) Application (2) Ventilation Prodoct Information Volume Agent Ratio Life Point TempF Humidity Cu.Ft./GaI

Ratio Base:Cure deg.F

Handle Hard Min Max Min Max 302H 78 PWD I TO 1 4 hrs 1 hrs 4 hrs 110° +- 10 32° 90° 85%

385 66 385 I TO 1 4 hrs 4 hrs 8 hrs 120° 65 32° 120° 85%

229T 45 229 4 TO 1 4 hrs 4 hrs 8 hrs 105° 911 32° 90° 85%

(13) Not more than __ % by volume.

Remarks: (14) No coating to be applied when substrate is within 5F of dewpoint.

STEEL PAGE 90F34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

ANCHOR SPOT BLAST TO SP-tO AND SANDSWEEP ALL REMAINING AREA TO REMOVE ALL

CONTAMlNATION.

SPREAD RATE @ SPEC. Overcoat Time Application Method SYSTEM INFORMATION COLOR TYPE WFT DFT DFT Sq_Ft. per Gal at 70F Airless Spray

COAT MILS MILS Conv. Airless Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

DL'v1ETCOTE 302H GREEN FULL 4.0 3.0 417 292 4 hrs lND. X .21

AMERCOAT 385 BLACK FULL 8.0 5.0 212 148 8 hrs 72 X .21 hrs

Solid Curing Mixed Pot DIY at 70F Flash Thinner (1) Application (2) Ventilation Product Infonnation Volume Agent Ratio Life Point TempF Humidity Cu.FUGal

Ratio Base: Cure deg. F

Handle Hard Min Max Min Max 302H 78 PWD 1 TO 1 4 hrs 1 hrs 4hrs 110° +- 10 32° 90° 85%

385 66 385 1 TO 1 4 hrs 4hrs 8hrs 120° 65 32° 120° 85%

(l 5) Not more than __ % by volume.

Remarks: (16) No coating to be applied when substrate is within 5F of dewpoint

STEEL PAGE 10 OF 34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

ANCHOR CHAIN SPOT BLAST TO SP·IO AND SANDSWEEP ALL REMAINING AREA TO REMOVE ALL

CONTAMINATION.

SPREAD RATE @ SPEC. Overcoat T ime Application Method SYSTEM INFOI,,\1ATION COLOR TYPE WFT DFT DFT Sq.Ft. per Gal at 70F Airless Spray

COAT MILS MILS Cony. Airless Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

DIMETCOTE 302H GREEN FULL 4.0 3.0 417 292 4 hrs IND. X .21

AMERCOAT 385 BLACK FULL 8.0 5.0 212 148 8 hrs 72 X .21 hrs

Solid Cnting Mixed Pot Dry at 70F Flash Thinner (I) Application (2) Ventilation Product Information Volmne Agent Ratio Life Point TempF Humidity CuR/Gal

Ratio Base: Cure deg. F

Handle Hard Min Max Min Max 30m 78 PWD I TO I 4 hrs I hrs 4 hrs 110' +-10 32' 90' 85%

385 66 385 I TO 1 4 hrs 4 hrs 8 hrs 120' 65 32° 120° 85%

(17) Not more than __ % by volmne.

Remarks: (18) No coating to be applied when substrate is within SF of dewpoint.

MARKINGS: A.,,\1ERCOAT 229C RED AT 2.0 MILS D.F.T.

Ai\1ERCOAT 229C WllITE AT 2.0 MILS D.F.T.

AMERCOAT 229C BLUE AT 2.0 MILS D.F.T.

STEEL PAGE 11 OF 34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

SPOT BLAST TO SP-IO AND SANDSWEEP ALL REMAINING AREA TO REMOVE ALL

CONTAMINATION.

SPREAD RATE @ SPEC. Overcoat Time ~Jication Method SYSTEM INFORMA nON COLOR TYPE WFT DFT DFT Sq.Ft. per Gal at 70F Airless Spray

COAT MILS MILS Conv. Airless Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

AMERCOAT 385 RED FULL 8.0 5.0 212 148 8hrs 6 X .21 mos

AMERCOAT 385 OFF SIC -- -- -- -- 8 hrs 6 X X WHITE mos

AMERCOAT 385 OFF FULL 8.0 5.0 212 148 N/A X .21

WHITE

Solid Curing Mixed Pot Dry at 70F Flash Thinner (I) Application (2) Ventilation Product Information Volume Agent Ratio Life Point TempF Humidity CU.Ft./Gal

Ratio Base: Cure deg. F

Handle Hard Min Ma" Min Max

385 66 385 I TO 1 4 hrs 4 hrs 8 hrs 1200 65 320 1200 85%

(19) Not more than _ _ % by volume.

AREA: SAL TWA TER BALLAST TANKS, PUMPABLE FIXED BALLAST TANKS, (20) No coating to be applied when substrate is within 5F of dewpoint.

SEWARGE AND GREY WATER TANKS. COFFERDAMS, CENTERBOARD INTERIOR

STEEL ABOVE WATERLINE, VOIDS AND MISCELLANEOUS TANKS.

STEEL PAGE l20F 34

COATINGS SPECIFICA nON OWNER: JOB:

AREA: SURFACE PREPARATION:

FRESH AND POTABLE WATER TANKS NEAR WHITE METAL BLAST SP.I0

SPREAD RATE @ SPEC. O vercoat Time Application Method SYSTElV! INFORMATION COLOR TYPE WIT DFT DFT Sq.Ft. per Gal at 70F Aidess Spray

COAT MILS MILS Cony. Airless Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

AMERLOCK 400 GREY FULL 6.0 5.0 266 186 12 hrs 10 X .21 days

AMERLOCK 400 OFF SIC -- -- -- -- 12 hrs 10 X X _w~~ _______________________________

WIllTE days

AMERLOCK 400 OFF FULL 6.0 5.0 266 186 N/A X .21

\VHITE

Solid Curing Mixed Pot Dry at 70F Flash Thinner (1) Application (2) Ventilation Product Information Volume Agent Ratio Life Point Temp F Humidity CU.Ft.lGal

Ratio Base:Cure deg. F

Handle Hard Min Max Min Max AMERLOCK 400 83 400 1 TO 1 4 hrs 8 hrs 12 hrs 110° 65 32° 120° 85%

(2 1) Not more than __ % by volnme.

Remarks: (22) No coating to be applied when substrate is within 5F of dewpoint.

ALLOW 7 DAYS MINIMUM WITH FORCED AIR CIRCULATION AFTER COMPLETE

SYSTEM IS APPLIED PRIOR TO FLUSHING AND FILLING TANKS!

STEEL PAGE 13 OF 34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

CHAIN LOCKER & SUMP SPOT BLAST TO SP-IO AND SANDSWEEP ALL REMAINING AREA TO REMOVE ALL

CONTAMINATION.

SPRFAD RATE @ SPEC. Overcoat Time Application Method SYSTEM INFORMATION COLOR TYPE WIT DIT DFT Sq.Ft. per Oal at 70F Aidess Spray

COAT MILS MILS Cony. Airless Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

AMERCOAT 385 WHITE FULL 8.0 5.0 212 148 8hrs 6 X .21 mas

AMERCOAT 385 RED SIC -- -- -- -- 8 hrs 6 X X mas

AMERCOAT 385 RED FULL 8.0 5.0 212 148 N/A X .21

Solid Curing Mixed Pot Dry at 70F Flash Thinner (I) Application (2) Ventilation Prodncl Information VoIUIlle Agent Ratio Life Point TempF Humidity Cu.Ft./Gal

Ratio Base:Cure deg. F

Handle Hard Min Max Min Max 385 66 385 I TO I 4 hrs 4 hrs 8 hrs 120° 65 32° 1200 85%

(23) Not more thall __ % by volUllle.

Remarks: (24) No coating to be applied when substrate is within 5F of dewpoint.

STEEL PAGE 14F034

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

ELECTRICAL EQUIPMENT IF REQUIRED FOR POWER TOOL CORRODED AREAS AND INSURE AREA IS CLEAN OF OIL AND DRY.

TOUCH UP OF FACTORY APPLIED SYSTEM

SPREAD RATE @ SPEC. Overcoat Time AppUcation Method SYSTEM INFORMATION COLOR TYPE WFT DFT DFT Sq.Ft. per Gal at 70F Airless Spray

COAT MILS MILS Conv. Airless Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

AMERCOAT 5450 GRAY FULL 7.0 3,0 241 168 N/A X .21

Solid Curing Mixed Pot Dry at 70F Flash Thinner (1) Application (2) Ventilation Product Information Volume Agent Ratio Life Poiut TempF Humidity Cu.Ft./Gal

Ratio Base:Cure deg. F

Handle Hard Min Max Min Max

5450 45 N/A N/A N/A 12hrs 24 hrs 98° N/A 32° 90° 85%

(25) Not more than __ % by volume.

Remarks: ALREADY PRE-PRIMED NEED APPLY ONLY FINISH P AlNT 5450 GRAY (26) No coating to be applied when substrate is within SF of dewpoint

STEEL PAGE 150F34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

VERTICAL LADDERS SEE REMARKS NOTED:

(OUTSIDE OF TANKS)

SPREAD RATE @ SPEC. Overcoat Time Application Method SYSTEM INFORMATION COLOR TYPE WFT DFT DFT Sq.Ft. per Gal at 70F AirIess Spray

COAT MILS MILS Conv. AirIess Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

AiVlERCOAT 5105 GRAY FULL 3.5 2 .. 0 481 337 8 hrs IND. X .21

AMERCOAT 5450 BLACK I FULL 7.0 3.0 241 168 N/A X .21

Solid Curing Mixed Pot Dry at 70F Flash Thinner (1) Application (2) Ventilation Product Information Volume Agent Ratio Life Point TempF Humidity CuR/Gal

Ratio Base:Cure deg. F

Handle Hard Min Max Min Max 5105 60 N/A N/A N/A 4 hrs 8 hrs 100° N/A 320° 90° 85%

5450 45 NlA N/A N/A 12 hrs 24 hrs 98° N/A 32° 90° 85%

Remarks: (27) Not more than __ % by volume.

NOTE: ALL II\'TERlOR VERTICAL LADDERS SHALL BE SPOT BLASTED TO SP-I0 (28) No coating to be applied when substrate is within 5F of dewpoint.

AND SANDSWEEP ALL AREAS IF THAT AREA HAS GONE THROUGH AUTOBLAST. IF

NOT ALL AREA WOULD NEED TO BE BLASTED TO SF-IO!

STEEL PAGE l60F34

COATINGS SPECIFICATION OWNER: JOB:

AREA: ALL EXPOSED INTERIOR STEEL SURFACE PREPARATION:

BULKHEADS AND OVERHEADS IN LIVING POWER TOOL OR WIRE BRUSH DAMAGED AREAS, WIPE DOWN ENTIRE AREA WITH A MILD

QUARTERS AND IN SERVICE SPACES, WORK DETERGENT AND RINSE.

SHOPS, STOREROOMS, DECK

SPREAD RATE @ SPEC. Overcoat Time Application. Method SYSTEM INFOR,VlATION COLOR TYPE WFT DFT DFT Sq.Ft. pet Gal at 70F Airless Spray

COAT MILS MILS Cony. Aidess Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

AMERCOAT 5105 GRAY FULL 3.5 2 .. 0 481 337 8 hrs IND. X .21

AMERCOAT 5450 RT-8205 FULL 7.0 3.0 241 168 N/A X .21

Solid Curing Mixed Pot Dry at 70F Flash Thinner (1) Application (2) Ventilation Product lnfomlation Volume Agent Ratio Life Point TempF Humidity Cu.FUGal

Ratio Base: Cure deg. F

Handle Hard Mill Max Mill Max 5105 60 N/A N/A N/A 4 hrs 8 hrs 100° N/A 320° 90° 85%

5450 45 N/A N/A N/A 12 hrs 24 98° N/A 32° 90° 85%

HRS

AREALOCKERS AND SIMILAR SPACES, INTERIOR RAILINGS, STANCillONS, AND ASSOCIATED (29) Not more than __ % by volume.

FITTINGS. (30) No coatillg to be applied when substrate is SPACES WITH JOINER PANELS #1277 AND #1286 -AMERON 5450 (COLOR) RT 8205 within SF of dewpciut.

STATEROOMS, HOSPITAL PASSAGE WAYS, SHIPS OFFICE, BRIDGE, MESS ROOM, LOUNGE AND

CONFERENCE ROOM.

SPACES FINISHED IN ST AlNLESS STEEL - AMERON 5450 (COLOR) RT 1503 SPACES W1TH JOINER PANEL #120 I - AMERON 5450 (COLOR) RT 1505 ALL MODULES (T&S), ALL LABS EXCEPT THE FISH AND WET LABS. NOTE THAT THE HYDRO LAB IS TO HAVE VERJI,fICULlTE IN THE

PAINT.

NOTE: MACHINERY SPACE TO BE COATED WITH 5105 PRIMER & AMERCOAT 5450 (COLOR) RT8205

STEEL PAGE 17 OF 34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

SPOT BLAST TO SP·IO AND SANDSWEEP ALL REMAINING AREA TO REMOVE ALL

CONTAMINATION.

SPREAD RATE @ SPEC. Overcoat Time Application Method SYSTEM INFOR>vtATtON COLOR TYPE WFf DFf DFI' Sq,Ft, per Gal at 70F Airless Spray

COAT MILS MILS Conv, Airless Theoretical Practical Min, Max, Brush Roller Spray Spray Nozzle Fan

AMERCOAT 385 DARK FULL 9,0 6,0 176 124 8hes IND X ,21

GREY

AMERCOAT 385 RED FULL 9,0 6,0 176 124 N/A X ,21

Solid Curing Mixed Pot Dry at 70F Flash Thinner (l) Application (2) Ventilation Product Information Volume Agent Ratio Life Point Temp F Hnmidity Cu,FUGaI

Ratio Base:Cure deg, F

Handle Hard Min Max Min Max

385 66 385 I TO I 4 hrs 4 hrs 8 hrs 120° 65 32° 120° 85%

AREA EXPOSED IN'TERIOR DECKS (6" UP ON VERTICAL SURF ACES) IN AUXILIARY (31) Not more thall __ % by volume, MACHINERY AND SERVICE SPACES, WORKSHOPS, STOREROOMS, DECK LOCKERS (32) No coating to be applied when substrate is within 5F of dewpoint

AND SIMILAR SPACES,

A MER ON PERFORMANCE COATINGS AND FINISHES GROUP

STEEL PAGE 180F34

COATINGS SPECIFICATION OWNER: JOB:

AREA: WALKING SURFACES OF FLOOR SURFACE PREPARATION:

PLATES, GRATES, DECKS, AND PLATFORMS SPOT BLAST TO SP.I0 AND SANDSWEEP ALL REMAINING AREA TO REMOVE ALL IN MAIN MACHINERY SPACES. CONTAMlNATION.

SPREAD RATE @ SPEC. Overcoat Time Application Method SYSTEM INFOllc\1£,\TION COLOR TYPE WFT DFT DFT Sq.Ft. per Gal ar 70F Airless Spray

COAT MILS MILS Conv. Aidess Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

AMERCOAT 385 RED FULL 9.0 6.0 176 124 8hrs IND X .21

AMERCOAT 385 DARK FULL 9.0 6.0 176 124 N/A X .21

GREY

Solid Curing Mixed Pot Dry at 70F Flash Thioner (1) Application (2) Ventilation Product Information Volume Agent Ratio Life Point TempF Humidity Cu.FUGal

Ratio Base:Cure deg. F

Handle Hard Min Max Min Max

385 66 385 I TO I 4 hrs 4 hrs 8 hrs 120° 65 32° 120° 85%

REMARKS: (33) Not more than __ % by volume.

(34) No coating to be applied when substrate is within SF of dewpoint

STEEL PAGE 190F34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION :

MACH AND FOUNDATIONS WITIIlN MACH POWER TOOL CORRODED AREAS

SPACES ABOVE FLOOR PLATES TEMP BELOW

200QF

SPRFAD RATE @ SPEC. Overcoat Time Application Method SYSTEM INFORMATION COLOR TYPE WFT DFT DFT Sq.Ft. per Gal at 70F Airless Spray

COAT MILS MILS Conv. Airless Theoretical Practical Mill. Max. Brush Roll Spray Spray Nozzle Fan er AMERCOAT 5105 RED FULL 3.5 2 .. 0 481 337 8 hrs IND. X .21

AMERCOAT 5450 BULK- FULL 4.0 2.0 361 253 N/A X .21

HEAD

GRAY

Solid Curiug Mixed Pot Dry at 70F Flash Thinner (1) APPlication (2) Ventilation Product Information Volume Agent Ratio Life Point TempF Humidity ClLFt.lGal

Ratio Base:Cure deg.F

Handle Hard Min Max Min Max 5105 60 N/A N/A N/A 4 hrs 8 hrs 100° N/A 320° 90° 85%

5450 60 N/A N/A N/A 4 hrs 8 hrs 120° N/A 32° 90° 85%

REMARKS: (35) Not more than __ % by volume.

(36) No coating to be applied when substrate is within SF of dewpoint

COATINGS SPECIFICATION OWNER: JOB:

I

I

AREA: SURFACE PREPARATION:

MACH SPACES BELOW LOWER LEVEL FLOOR SPOT BLAST TO SP-IO SANDSWEEP ALL REMAINING AREA.

PLATES: ETC:

(CONTINUED IN REMARKS) NOTE: ANY REPAIR TO BURN DAMAGE MAY BE POWER TOOL CLEANED

SPREAD RATE @ SPEC. Overcoat Time Application Method SYSTEM INFORMATION COLOR TYPE WFT DFT DFT Sq.Ft. per Gal at 70F Airless Spray

COAT MILS MILS Conv. Airless Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

DlMETCOTE 302H GREEN FULL 4.0 3.0 417 292 4 hrs IND. X .21

AMERCOAT 385 RED FULL 9.0 6.0 176 124 N/A X .21

Solid Curing Mixed Pot Dry at 70F Flash Thinner (1) Application (2) Ventilation Product Information Volume Agent Ratio Life Point TempF Humidity Cu.Ft./Gal

Ratio Base:Cure deg.F

Handle Hard Min Max Min Max 302H 78 PWD 1 TO I 4 hrs I hrs 4 hrs lIOo +·10 32° 90° 85%

385 66 385 1 TO 1 4 hrs 4 hrs 8 hrs 120° 65 32° 120° 85%

(37) Not more than __ % by volume.

Remarks: (38) No coating to be applied when substrate is withiu 5F of dewpoint.

INCLUDING FLOOR PLATE SUPPORTS, FOUNDATIONS, TANK TOPS BILGE WELLS,

FERROUS PIPE AND OTHER STEEL SURFACES!

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

UNEXPOSED STEEL BEHIND INSULATION POWER TOOL CORRODED AREAS

AND JOINER WORK

SPREAD RATE @ SPEC. Overcoat Time Application Method SYSTEM INFORMATION COLOR TYPE WFT DFT DFT Sq.Ft. per Gal at 70F Airless Spray

COAT MILS MILS Conv. Airless TIlcoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan i\.".1ERCOAT 5105 RED FULL 3.5 2.0 481 337 8 hrs IND X .21

Solid Curing Mixed Pot Dry at 70F Flash Thinner (1) Application (2) Ventilation Productlnfonnation Volume Agent Ratio Life Point TempF Humidity Cu.Ft./Gal

Ratio Base:Cure deg. F

Handle Hard Min Max Min Max

5105 60 N/A N/A N/A 4 hrs 8 hrs 100° N/A 32° 90° 85%

NON ACOUSTIC AREA: (39) Not more than __ % by volume.

TOP COAT WITH 5450. (40) No coating to be applied when substrate is "ithin 5F of dewpoint.

ALUMINUM PAGE 220F34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

(CONTINUED IN REMARKS) LIGHT SAND SWEEP TO ETCH ALUMINUM

SPREAD RATE @ SPEC. Overcoat Time Application Method SYSTEM INFORMATION COLOR TYPE WFT DFT DFT Sq.Ft. per Gal at 70F Airless Spray

COAT MILS MILS Conv. Airless Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

AMERCOAT 385 RED FULL 8.0 5.0 212 148 8hrs 72 X .21 hrs

AMERCOAT 229T WHITE FULL 4.0 2.0 361 253 NIA X .21

Solid Curing Mixed Pot Dry at 70F Flash Thinner (1) Application (2) Ventilation Product Information Volume Agent Ratio Life Point TempF Humidity Cu.Ft./GaI

Ratio Base:Cure deg. F

Handle Hard Min Max Min Max

385 66 385 1 TO 1 4 hrs 4 hrs 8hrs 120° 65 32° 120° 85%

229T 45 229 1 TO 1 4 hrs 4 hrs 8 hrs 105° 911 32° 90° 85%

Remarks: (41) Not more than __ % by volume.

EXTERIOR ALUMINUM SIS, DECKHOUSE, VENTS, OVERFLOWS, OVERHEAD (42)No coating to be applied when substrate is within 5F of dewpoint.

SURF ACES, DECK GEAR LOCKERS, DOORS, STANCHIONS, EXTERIOR VENTICAL

AND INCLINED LADDERS, HANDRAILS, BREAKWATERS, VENTILATORS, STACK,

BUL W ARK MOlJNTED CHOCKS, DAVITS AND RAILS!

ALUMINUM PAGE 23 OF 34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

REMARKS LIGHT SAND SWEEP TO ETCH ALUMINUM OR APPLY ONE FULL COAT GALV APREP PRIMER

SPREAD RATE @ SPEC. Overcoat Time Application Method SYSTEM INFORMATION COLOR TYPE WFT OFT OFT Sq.Ft. per Gal at 70F Airless Spray

COAT MILS MILS Conv. Airless Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

AMERCOAT 385 RED FULL 9.0 6.0 176 124 8hrs [NO X .21

AMERCOAT 385 DARK FULL 9.0 6.0 176 124 N/A X .21

GRAY

(WITH #888 NON SKID)

Solid Curing Mixed Pot Dry at 70F Flash Thitmer (1) Application (2) Ventilation Product lufonnation Volume Agent Ratio Life Point TempF Humidity Cu. Ft./Ga\

Ratio Base: Cure deg. F

Handle Hard Min Max Min Max

385 66 385 I TO 1 4 hrs 4hrs 8hrs 1200 65 320 1200 85%

REMARKS: (43)Not more than __ % by volume.

ALL ALUMINUM EXTERIOR DECKS (6" UP ON VERTICAL SURFACES) HOUSE TOPS, (44)No coating to be applied when substrate is within SF of dewpoint.

EXTERIOR HATCH COVERS, FOUNDATIONS, DECK FITTINGS AND INBOARD SIDE

OF BULWARKS. NON SKID GRIT #888 IS TO BE ADDED TO THE FINISH COAT ON

ALL DECK SURFACES.

ALUMINUM PAGE 240F34

COATINGS SPECIFICATION OWNER: JOB:

AREA; SURFACE PREPARATION:

ALL EXTERIOR FOUNDATIONS, DECK LIGHT SAND SWEEP TO ETCH ALUMINUM

FITTINGS AND WEATHER HATCH COAMINGS

SPREAD RATE @ SPEC. Overcoat Time Application Method SYSTEM IN FORMA TION COLOR TYPE WFT DFT DFT Sq.Ft. per Gal at 70F Airless Spray

COAT MILS MILS Conv. Airless Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

AMERCOAT 385 RED FULL 9.0 6.0 176 124 8hrs IND X .21

AMERCOAT 385 DARK FULL 9.0 6.0 176 124 N/A X .21

GRAY

i Solid Curing Mixed Pot Dry at 70F Flash Thumer (1) Application (2) Ventilation

Product Information Volume Agent Ratio Life Point TempF Humidity Cu.Ft./GaI Ratio Base:Cure deg. F

Handle Hard Mill Max Min Max

385 66 385 1 TO I 4 hrs 4 hrs 8 hrs 120· 65 32· 120· 85%

AREA (45) Not more than __ % by vol1lllle.

(46) No coating to be applied when substrate is withiJl 5F of dewpoint.

ALUMINUM PAGE 25 OF 34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURPACE PREPARATION:

INTERIOR PILOTHOUSE OVERHEAD LIGHT SAND SWEEP TO ETCH ALUMINUM

Overcoat Time Apphcation Method SYSTEM INFORMATION COLOR TYPE WFT DFT at 70F AirIess Spray

COAT MILS MILS Cony. Aidess Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

AMERCOAT 385 RED FULL 8.0 5.0 212 148 8hrs 72 X .21 hrs

AMERCOAT 229T BLACK FULL 4.0 2.0 361 253 N/A X .21

Solid Curing Mixed Pot Dry at 70F Flash Thinner (1) Application (2) Ventilation Productllifonnation Volume Agent Ratio Life Point TempF Humidity eu.FUGaI

Ratio Base:Cure deg. F

Handle Hard Min Max Min Max

385 66 385 1 TO 1 4 hrs 4 hrs 8 hrs 1200 65 320 1200 85%

229T 45 229 4TO 1 4 hrs 4 hrs 8 hrs 1050 911 32° 90° 85%

REMARKS: (47) Not more than __ % by volume.

UNDERSIDE OF PILOTHOUSE VISOR AND OVERHEAD AMERCOAT 229T BLACK (48) No coating to be applied when substrate is within SF of dewpoint.

ALUMINUM PAGE 26F034

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURPACE PREPARATION:

MASTS, BOOMS, TRUSSES, JACK AND ENSIGN LIGHT SAND SWEEP TO ETCH ALUMINUM

STAFF, KINGPOSTS AND SIMILAR FITTINGS

Overcoat Time Application Method SYSTEM INFORMATION COLOR TYPE WFT OFT at 70F Airless Spray

COAT MILS MILS Conv. Airless Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

AMERCOAT 385 RED FULL 8.0 5.0 212 148 8hrs 72 X .21 hrs

AMERCOAT 229T BUFF FULL 4.0 2.0 361 253 N/A X .21

Solid Curing Mixed Pot Dry at 70F Flash Thinner (I) Application (2) Ventilation Product Information Volume Agent Ratio Life Point Temp F Humidity Cu.Ft./GaI

Ratio Base:Cure deg. F

Handle Hard Min Max Min Max

385 66 385 I TO 1 4 hrs 4hrs 8 hrs 120' 65 32' 120' 85%

229T 45 229 4 TOI 4 hrs 4 hrs 8 hrs 105' 911 32' 90' 85%

REMARKS: (49) Not more !han __ % by volume.

(50) No coating to be applied when substrate is within 5F of dcwpoint.

AMffiRONPERFORMANCECOATINGSANDF~SHESGROUP

ALUMINUM PAGE 270F34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

INTERIOR OF ROLL STABILIZATION TANK LIGHT SAND SWEEP TO ETCH ALUMINUM

A1\'D ALUMINUM PORTION OF

CENTERBOARD TRUNK

SPREAD RATE @ SPEC. Overcoat Time Application Method SYSTEM INFORMATION COLOR TYPE WFT DFT DFT Sq.Ft. per Gal at 70F Airless Spray

COAT MILS MILS Cony. Airless Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

AMERCOAT 385 RED FULL 8.0 5.0 212 148 8hrs 6 X .21 mos

OFF -- -- 8 hrs 6 x AMERCOAT 385 WH1TE SIC -- -- mos

AMERCOAT 385 OFF FULL 8.0 56.0 212 148 NIA X .21

WH1TE

Solid Curing Mixed Pot Dry at 70F Flash Thinner (I) Application (2) Ventilation Product Information Volume Agent Ratio Life Point TempF Humidity eu.FUGaI

Ratio Base:Cure deg. F

Handle Hard Min Max Min Max

385 66 385 1 TO 1 4 hrs 4 hrs 8 hrs 120' 65 32° 120' 85%

REMARKS: (51)Not more than __ % by volmne.

(52) No coating to be applied when substrate is ",thin 5F of dewpoint.

ALUMINUM PAGE 280F34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

EXPOSED INTERIOR LIGHT ETCH THE ALUMINUM

(CONTINUED IN REMARKS)

SPREAD RATE @ SPEC. Overcoat Time Application Method SYSTEloj fNFORMA TfON COLOR TYPE WFT DFT DFT Sq.Ft. per Gal at 70F Airless Spray

COAT MfLS MfLS Conv. Airless -- Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

AMERCOAT 385 wmTE FULL 8.0 5.0 212 148 6HRS 3 X .21

AMERCOAT 5450

I DAYS

X .21

FELL 7.0 3.0 241 168 N/A

i Solid Curing Mixed Pot Dry at 70F Flash Thinner (I) Application (2) Ventilation

Product Infonnation Volume Agent Ratio Life Point TempF Humidity CU.Ft/GaI Ratio Base:Cure deg.F

Handle Hard Min Max Min Max

385 66 385 I TO I 4 hrs 4 hrs 8 hrs 120° 65 32° 120° 85%

5450 45 N/A N/A N/A 8hrs 12hrs 98° N/A 32° 90° 85% I

I

REMARKS: (53) Not more than ___ % by volume.

BULKHEADS AND OVERHEADS IN LIVING QUARTERS, PELOT HOUSE, MACHINERY AND (54) No coating to be applied when substrate is within 5F of ;

SERv1CE SPACES, WORKSHOPS, STOREROOMS, DECK LOCKERS AND SIMILAR SPACES, de"'Point.

EXPOSED ]]\;'TERIOR ALlJM]]\;'UM,INTERlOR RAELINGS, STANCHIONS AND ASSOCIATED

FITTINGS!

SPACES WIlli JOINER P~'ffiLS #1277 A."ID #1286 - AMERON 5450 (COLOR) RT8205

STATEROOMS, HOSPITAL, PASSAGE WAYS, SHIPS OFFICE, BRIDGE, MESS ROOM,

LOUNGE M'D CONFERENCE ROOMS.

SPACES FINISHED IN STAINLESS STEEL - AMERON 5450 (COLOR) RT 1503

SPACES WITH JOINER PA.'ffiLS #1201 - AMERON 5450 (COLOR) RT 1505

ALL T & S MODULES, ALL LABS EXCEPT THE FISH AND WET LABS.

NOTE: THAT THE HYDRO LAB IS TO HAVE VERl\1ICULITE IN THE PAINT.

ALUMINUM PAGE 29 OF 34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

DECKS (6" ON VERTICAL SURFACES) IN LIGHT SWEEP T O ETCH THE ALUMINUM

MACH

(CONTINUED IN REMARKS)

SPREAD RATE @ SPEC. Overcoat Time Application Method SYSTEM INFORMATION COLOR TYPE WFT OFT OFT Sq.Ft. per Gal at 70F Airless Spray

COAT MILS MILS Conv. Airless Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

AMERCOAT 385 DARK FULL 9.0 6.0 176 124 8hrs IND X .21

GREY

AMEROCAT 385 RED FULL 9.0 6.0 176 124 N/A X .21

Solid Curing Mixed Pot Dry at 70F Flash Thinner (I) Application (2) Ventilation Product Information Volume Agent Ratio Life Point TempF Humidity Cu.Ft./Ga1

Ratio Base:Cure deg. F

Handle Hard Min Max Min Max

385 66 385 I TO 1 4 hrs 4 hIS 8 hrs 1200 65 320 1200 85%

REMARKS: (55)Not more than __ % by volume.

AND SERVICE SPACES, WORKSHOPS, STOREROOMS, EXPOSED INTERIOR DECKS, (56) No coating to be applied when substrate is within 5F of dewpoint.

DECK LOCKERS AND SIMILAR SPACES!

ALUMINUM PAGE 30 OF 34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

FLOOR PLATES, DECKS AND PLATFORMS IN LIGHT SWEEP TO ETCH THE ALUMINUM

MACH SPACE

SPREAD RATE @ SPEC. Overcoat Time Application Method SYSTEM INFORMATION COLOR TYPE WFT DFT DFT Sq.Ft. per Gal at 70F Airless Spray

COAT MILS MILS Cony. Airless Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

AMERCOAT 385 RED FULL 9.0 6.0 176 124 8hrs IND X .21

AMEROCAT 385 DARK FULL 9.0 6.0 176 124 N/A X .21

GREY

Solid Curing Mixed Pot Dry at 70F Flash Thinner (1) Application (2) Ventilation Product Information Vohune Agent Ratio Life Point TempF Humidity Cn.FUGal

Ratio Base:Cnre deg. F

Handie Hard Min Max Min Max

385 66 385 lTD I 4 hrs 4 hrs 8 hrs 1200 65 320 1200 85%

REMARKS: (57) Not more than _ _ % by volume.

(58) No coating to be applied when substrate is within 5F of dewpoint.

ALUMlN1JM PAGE 31 OF 34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

MACH & FOUNDATIONS ETCH THE ALUMINUM

BELOW 200· (CONTINUED IN REMARKS)

SPREAD RATE @ SPEC. Overcoat Time Application Method SYSTEM IN FORMA TION COLOR TYPE WFT DFT DFT Sq.Ft. per Gal at 70F AirIess Spray

COAT MILS MILS Conv. Airless Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

AMERCOAT 385 EQUIP. FULL 8.0 5.0 212 148 N/A X .21

GREY

Solid Curing Mixed Pot Dry at 70F Flash Thinner (1) Application (2) Ventilation Product Information Volume Agent Ratio Life Point TempF Humidity Cu.FUGaI

Ratio Base:Cure deg. F

Handle Hard Min Max Min Max

385 66 385 I TO 1 4 hrs 4 hrs 8 hrs 120° 65 32° 120° 85%

REMARKS: (59) Not more than __ % by volume.

MACHINERY AND FOUNDATIONS WITHIN MACHINERY SPACES ABOVE FLOOR (60) No coating to be appliod when substrate is within SF of dcwpoint.

PLATES WHERE TEMP IS BELOW 200°[1

ALUMINUM PAGE 33 OF 34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

STACK MARKINGS

SPREAD RA IE @ SPEC. Overcoat T ime Application Method SysTSV11NFOIU"IA nON COLOR TYPE WFT DFT DFT Sq.Ft. per Gal at 70F Airless Spray

COAT MILS MILS Conv. Airless Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fao

Solid Curing Mixed Pot Dry at 70F Flash TItinner (1) Application (2) Ventilation Product luformation Volume Agent Ratio Life Point TempF Humidity Cu.Ft.lGaI

Ratio Base:Cure deg. F

Handle Hard Min Max Min Max

AMERCOAT 229T 45 229T 4 to II 4 hrs 4 hrs 8 hrs 105° 911 32° 90° 85%

REMARKS: (63) Not more than ~_% by volume.

TOP BAND BLACK AMERCOAT 229T 2115 STACK HEIGHT (64) No coating to be applied when substrate is within 5F of dewpoint.

MIDDLE BAND LIGHT BLUE Il lS STACK HEIGHT BOTTOM BAND DARK BLUE 1115 5T ACK I-lEIGHT

PAGE 340F34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

FUEL, LUBE AND DIRTY OlL TANK

BROOM SWEEP

SPREAD RATE @ SPEC. Overcoat Time Application Method SYSTEM INFORMATION COLOR TYPE WFT OFT OFT Sq. Ft. per Gal at 70F Airless Spray

COAT MILS MILS Conv. Airless Theoretical Practical' Min. Max. Brush Roller Spray Spray Nozzle Fan

Solid Curing Mixed Pot Dry at 70F Flash Thinner (I) Application (2) Ventilation Product Information Volume Agent Ratio Life Point Temp F Humidity Cu.FUGaI

Ratio Base:Cure deg. F

Handle Hard Min Max Min Max

(65) Not more than ___ % by volume.

(66) No coating to be applied when substrate is within 5F of dewpoint.

NO PAINT TO BE APPLIED

ALUMINUM PAGE 320F34

COATINGS SPECIFICATION OWNER: JOB:

AREA: SURFACE PREPARATION:

UNEXPOSED ALUMINUM BEHIND

INSULATION AND JOINER WORK NO COATING REQUIRED

(CONTINUED IN REMARKS)

SPREAD RATE @ SPEC. Overcoat Time Application Method SYSTG\I INFOR.\IA TION COLOR TYPE WFT OFT OFT Sq.Ft. per Gal at 70F AirJess Spray

COAT MILS MILS Conv. Airless Theoretical Practical Min. Max. Brush Roller Spray Spray Nozzle Fan

Solid Curing Mixed Pot Dry at 70F Flash Thhmer (1) Application (2) Ventilation Product Information Volume Agent Ratio Life Point TempF Huntidity Cu.FtlGaI

Ratio Base: Cure deg. F

Handle Hard Min Max Min Max i REMARKS: (61) Not more than __ % by volume.

NON-ACOUSTIC (62) No coating to be applied when substrate is within 5F of dewpoint.

EXPOSED INSULATION SHALL BE TOPCOATED WITH ONE 3.0 MIL D.F.T. TOPCOAT

OF AMERCOAT 5450 WHITE

Amercoat® 2291 Gloss epoxy topcoat

Product Datal Application Instructions

• Gloss topcoat with unlimited recoatability

• Combines the durability and toughness of epoxy with the color and gloss retention of the acrylic polymer

• LowVOC

• Resistant to a broad range of corrosive atmospheres

• Resists soH pickup ~ cleans easily e Hard, flexible and abrasion resistant

Typical Uses Arnercoat 229'1' can be used as a finish coat where attractive appearance and a wide range of corrosion resistanee is requiredl.

• All above-water areas on ships

• Dock side structures and equipment

• Off shore platforms

• Petroleum refineries and containers

• Chemical plants

• General industrial and marino applications

Typical Systems

1st Coat

Amercoat 235, Amercoat 240, Amorcoat 370 or Amercoat 385

Amerlock Series

Amercoat 68HS or Amercoat 302H

2nd Coat

Amercoat 229'1'

Amercoat 229T

Amercoat 385

:lrdCoat

Amercoat 229T

,,1 of 4

Physical Data Finish Closs

Color* See color card

Components 2

Mixing ratio 4 parts resin to 11nart cure (by volume)

Curing mechanism Solvent rBlease ree

Volume Solids 56%± 3%

VOC (EPA Method 24) lb/gal giL unthinned 3.2 384 thinned (" - pinl/gal) 3.5 420

Dry film thickness (per coat) 2-4 mils (50-100

Coals lor 2

Theoretical coverage ft2/gal m2/L 2 mil 449 11.0 4 mils 224 5.5

Temperature rnsistancB, dry

OF 'C

continuous 200 93 intermittent 250 121

Fla..sh Point OF °C cure 80 27 rnsin 108 42 Alnercoat 65 78 2J::: .J

Amercoat 101 145 63 Amercoa.t 12 2 -1 7

Thinners Amercoat 65, Clea.ner Amercoat 12

. ,. ,. .. may requilje additional coats to achirme adequate hiding. particularly when applied oller d4rk or contrasting primer than with stan.~ard producliOl: batch?s. {( colDr is critic~l, Cht[!e batches at natu.ral breaks 111 struc/,ure or tnlermlX batch.esfor COflslstenc .

Yellow. red and orange colors willfadefaster than olher color due to the replacement of lead-based pigments with lead-fi"ee pigments 1 these colors.

Application Equipm nt The following is a guide; suit hIe equipment from other manufacturers may be used Changes in pressure and tip size may be needed for proper s ray characteristics.

Ail-less spray-Standard e lipment such as Graco, DeVilbiss, Binks, Speeflo, or others hay ng a 30: 1 or higher pump ratio and it Huid tip with 0.G17- to 0.021-inch orifice.

Conventional spray-Indu. trial c-::quipment such as DeVilbiss or Binks spray gUll. Separatt air and fluid pressure regulators, and a moisture and oil trap i 1 main air supply line are recommended.

Brush or roller ~ Natural brittle brush or solvent-resistant roller with %-inch to %-inch I ap. For best (l"ppearance when rolling, level any air bubbles with bristle brush.

Application Procedu e Amercoat 2291' is packaged n two components in the proper proportions which must be lixed together bcti'Jr8 use:

1. Flush equipment with thi mer or Amercoat 12 before use.

2. Stir each component thor ughly, then add cure to resin and mix until uniformly blend)d to a workable consistency. Do not mix more material th n will be used within 6 hours at 65-80°F (18-2rC). Pot Iij', is shortened by higher tempera tures. See pot life data.

3. If relative humidity is less than 70r ;.;), no induction time is required. If relative hurni ity is 70(;{) or greater, allow the mixed material to sit for 3 minutes prior to the start of the application. After the ind etioll periods has elapsed, stir the mixed material again to e Isure that it is uniformly blended, then proceed with the ap lieation.

4. Thin only if necessary for orkability.

5. When applying by conve tioHa.l spray, use adequate air pressure and volume to e sure proper atomization.

6. Apply a wet coat in even 1 arallel passes, oV(~rlap 50 percent to avoid holidays, bare ar ,as and pinholes. Ifrequired, cross spray at right angles.

7. Application of 5.4 mils 0'i5 microns) wet mm thickness will normally provide 3 mils ( 5 microns) dry film.

8. Clean all equipment with hinner or Amercoat 12 immediately after use.

Page30t4

Shipping Data Packaging unit" I ga.l cure 0.2 galin 1-qt can resin 0.8 gal in I-gal can

Shipping weight (approx) Ib

I-gal unit cure 3 resin 11

5-gal unit cure 9 resin 55

5-gal 1 gal in l-gal can 4 gal in 5-gal can kg

1.4 s.n

4.1 2c

Shelflife when stored indoors at 40 to 1 (lO'F (4 to 38'C) resin and cure 1 yoar from shipmE-mt date

229T PrJ/AI