CED 2P22-E Table- end cap- European style.pdf
PDF 156 KB Posted
- Attached to
- Wooden Display Fixtures
- Solicitation number
- HQC004-25-Q-E014
- Issued by
-
Defense Commissary Agency
About this file
This document is a Minimal Acceptable Standards specification for a European-style mobile end cap table for produce displays, issued by the Defense Commissary Agency (DeCA). The specification details a wooden display fixture with precise dimensional requirements of 72 inches long/wide, 30 inches deep, and 46 inches high, constructed of light oak with moisture-resistant sealant. Key features include four adjustable steel legs, casters, plastic liners, a plastic bumper, and three stepped display decks with varying lengths and depths.
The specification mandates that the end cap must be shipped fully assembled and ready to use, with a one-year warranty covering parts, service, and labor. The contractor must provide a point of contact for service, installation and operating instructions, and a parts list at delivery. DeCA requires continued parts support for the equipment's projected life cycle plus an additional 5 years. The document is part of a broader market research effort for wooden display fixtures across commissary locations, with potential solicitation number HQC004-25-Q-E014.
View the file
Other files
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
INITIATED
11/13/17
CED
PRODUCE
DEPARTMENT
Minimal Acceptable Standards
REVISION
04/12/24
2P22-E Table, end cap, European style PAGE 2 of 4
FY16r.05
1 Purpose of this Equipment: To serve as mobile end caps for produce displays and increase usable merchandising area.
2 Federal Supply Class: 7125
3 General Operating Specifications:
3.1 Dimensions:
3.1.1 72 inches long / wide, 30 inches deep, 46 inches high.
3.1.2 Dimensional sizes may vary plus or minus 2 inches in any direction.
3.2 Salient Characteristics that shall be provided:
3.2.1 Oak construction.
3.2.2 Moisture resistant protective sealant.
3.2.3 Casters: 2 swivel and minimum 2 locking.
3.2.4 Four adjustable steel legs.
3.2.5 Plastic liners on product display surface.
3.2.6 Plastic bumper extending around the front and sides of the end cap.
3.2.7 Front corners, left and right, to be cut off on a diagonal line to eliminate the sharp corners and to give the unit a polygon appearance.
3.2.8 Bottom shelf/display deck extending the full length of the end cap.
3.2.9 Upper ledge of end cap extending 2 inches above the bottom shelf/display deck.
3.2.10 Three stepped shelf/display decks.
3.2.11 Base shelf/display deck to be 55 inches long by 20 inches deep.
3.2.12 Middle shelf/display deck to be 40 inches long by 12 inches deep.
3.2.13 Top shelf/display deck to be 26 inches long by 5 inches deep.
3.2.14 Overflow pallet at the bottom located under end cap:
3.2.14.1 49 inches long / wide, 30 inches deep, 5 inches high.
3.2.14.2 Attached to tracks which are mounted on the inside edge of the left and right side of the end cap’s legs.
3.2.14.3 Able to slide forward and backward within the tracks.
3.2.15 Back panel:
3.2.15.1 Top edge is sloped from both ends
3.2.15.2 Sloped ends measure to a height of 23 inches above the bottom display deck
3.2.15.3 Flat top measures 27 inches across.
3.3 Industry Standards / Requirement(s):
3.3.1 Warranty period shall be for (1) year from date of delivery against defective material and workmanship and shall include parts, service and labor.
INITIATED
11/13/17
CED
PRODUCE
DEPARTMENT
Minimal Acceptable Standards
REVISION
04/12/24
2P22-E Table, end cap, European style PAGE 3 of 4
FY16r.05
3.4 Information Technology requirements: N / A
3.5 Color Requirement(s): Light Oak
4 Electrical Requirements: N / A
5 Standard Contractor Requirements:
5.1 Must be shipped assembled and ready to use
5.2 Information to be provided by the Contractor to the commissary at the time of delivery:
5.2.1 Point of Contact for Service
5.2.2 Installation and Operating Instructions
5.2.3 Parts List
5.3 Maintenance Sustainability Requirements: Continued parts support is required for the projected life cycle of the equipment plus 5 years.
6 Special Coordinating / Safety Instructions: N / A
| 1 Purpose of this Equipment: To serve as mobile end caps for produce displays and increase usable merchandising area. |
| 3.3 Industry Standards / Requirement(s): |
| 3.5 Color Requirement(s): Light Oak |
| 5 Standard Contractor Requirements: |
| 6 Special Coordinating / Safety Instructions: N / A |
File details come from the government source that posted it. Updated .