C68-0001AM.22 Truck Mounted Attenuator A6.xlsx
XLSX spreadsheet 19 KB Posted
- Attached to
- Truck and Trailer Attenuator Contract
- Solicitation number
- RFP 591 220000001069 1
- Issued by
- Michigan
About this file
This is a specification document issued by Department 591 (RFP No. 220000001069) for a truck-mounted attenuator system meeting ASHTO Report MASH (2016) TL3 standards. The attenuator is a replaceable cartridge system designed for installation on trucks with a gross vehicle weight rating of 37,000 pounds. The system must weigh approximately 1,795 pounds and consist of a bi-folding articulating frame assembly, dual cartridge system, support structure, underride design, and hydraulic system for raising and lowering the unit. The attenuator shall feature LED lighting compliant with FMVSS 108 standards, including brake, tail, ICC bar, and turn signals, along with two synchronized amber/green LED strobe lights in the rear strike plate. The system must be capable of quick attachment and detachment from the vehicle while keeping major components together, and shall include four hand-crank jacks with swivel casters for removal and storage.
The specification requires that all materials be new and of the latest production model, with all welding performed by or under the direction of a certified welder and all metal work manufactured in America. The attenuator must pass all ASHTO Report MASH (2016) TL 3 tests (TL 3-50 through TL 3-54) when mounted to a truck weighing up to 9,000 kilograms with automatic transmission in neutral and parking brakes locked on clean, dry pavement. The system must feature a hydraulic lock mechanism with manual mechanical backup to secure the frame assembly at 90 degrees, and the exit velocity of impacting vehicles shall not exceed 5 percent of incoming velocity. Contractors must respond with "YES" to each specification section or provide detailed explanations and available alternatives if unable to comply.
View the file
Other files
| File | Type | Posted |
|---|---|---|
| C68-0501A.22 Trailer Mounted Attenuator A4.xlsx | XLSX spreadsheet | |
| Schedule A.docx | DOCX document | |
| Standard Contract Terms.docx | DOCX document | |
| C68-0501.22 Trailer Mounted Attenuator A3.xlsx | XLSX spreadsheet | |
| C68-0001A.22 Truck Mounted Attenuator A2.xlsx | XLSX spreadsheet | |
| C68-0001M.22 Truck Mounted Attenuator A5.xlsx | XLSX spreadsheet | |
| Schedule B Pricing.xlsx | XLSX spreadsheet | |
| RFP Instructions.docx | DOCX document | |
| C68-0001.22 Truck Mounted Attenuator A1.xlsx | XLSX spreadsheet | |
| C68-0501M.22 Trailer Mounted Attenuator A7.xlsx | XLSX spreadsheet |
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
Sheet1
| RFP Dept. 591, No. 220000001069 | |
| Specification # C68-0001AM.22 Truck Mounted Attenuator, Replaceable Cartridge. Meeting ASHTO Report MASH (2016) TL3 Standards |
All items specified and furnished by the Contractor shall be new of the latest model in current production and shall include all standard features normally offered with these models CONTRACTOR must respond to each section with YES. (or additional information as requested)
If NO is indicated provide explanation and available option.
| Contract to identify proposed make and model | ||
| Brands or trade names are for identification purposes only and do not limit the Contractor to such brands | Make and Model | |
| 1.0 | Basic Requirements: | |
| 1.1 | All wires passing through holes in metal or non-metal wearing surfaces, which could cause wear of the insulation, shall be adequately protected by rubber or plastic grommets, and/or non-metal conduit. Ends of all wires shall be adequately anchored to prevent loosening. All wiring shall be properly secured to the unit by proper wiring hangers. |
| 1.2 | Ends of all wires shall be adequately anchored to prevent loosening |
| 1.3 | All electrical connections shall be soldered and enclosed in heat shrink or in water tight junction blocks |
| 1.4 | Scotch locks and wire nuts are not acceptable |
| 1.5 | Unit number will be provided and shall be welded to the unit in 2 inch high numbers or welded or stamped to a plate and bolted to the unit |
| 1.6 | Truck mounted system shall be designed for installation at the back of a truck with a gross vehicle weight (GVW) of 37,000 pounds and attached to the vehicle undersides with a quick attachment |
| 1.7 | Hitch assembly shall in no way hinder the operation of an underbody plow blade in its operation of raise and lower or traverse from right to left. |
| 1.8 | Attenuator shall consist of the following basic components: |
| a | Bi-folding articulating frame assembly |
| b | Dual cartridge system |
| c | Support structure |
| d | An under-ride design for attaching the system to the truck |
| e | Hydraulic system to raise and lower the unit |
| 1.9 | Both cartridges shall also be included in the system to raise the frame assembly and cartridge to a vertical position |
| 2.0 | When frame is in horizontal position the frame assembly shall be capable of collapsing when impacted by an errant vehicle |
| 2.1 | Total weight of system shall be approximately 1,795 pounds |
| 2.2 | Attenuator shall be designed to make attachment or detachment from the truck simple and fast with the major components listed above remaining together when detached from the support vehicle |
| 2.3 | Attenuator shall have a standard trailer lighting system compliant with FMVSS 108 standards, wired for turn signals independent of stop lights |
| 2.4 | Lighting system shall include brake, tail, ICC bar, and turn signals that are LED type |
| 2.5 | Wiring for the rear lights shall be routed and secured in the system frame |
| 2.6 | Light connector shall be round 7 pin Berg type |
| 2.7 | Light connector wired to MDOT specifications |
| 2.8 | Lights shall be provided that are visible whether the system is in travel position or operating position |
| 2.9 | Two (2) flush mount strobe lights which are synchronized shall be provided in the rear strike plate, lights shall be an amber/green LED combination light. Flash pattern is to be set to the following pattern, Amber - Quad fast flash, Green - Single slow flash. 4" round Whelen # 2EP00ZCRMDOT, Oval # 50AG2ZCRMDOT or equivalent |
| 3.0 | Four (4) hand crank jacks with swivel casters shall be attached to the system to allow removal of the unit from the truck for storage |
| 3.1 | Rear strike facing surface of the frame assembly shall display a black on yellow inverted "V" chevron pattern with a 4" wide color bands when in the horizontal position |
| 3.2 | All welding shall be done by, or under the direction of a certified welder |
| 3.3 | Metal work shall be made in America |
| 3.4 | All exposed metal of the attenuator shall be primed and painted black, unless it is galvanized |
| 3.5 | Hydraulic system shall consist of a pump with a 12 or 24 volt DC motor, cylinders, hoses, switches, wiring and necessary subcomponents to tilt the frame assembly to a 90 degree position from horizontal |
| 3.6 | Hydraulic system shall hydraulically lock to secure the frame assembly in the 90 degree position |
| 3.7 | A manual mechanical lock mechanism shall also be provided |
| 3.8 | The attenuator system shall be capable of tilting 5 degrees from horizontal when the back end of the attenuator contacts a rigid surface such, as a driveway |
| 3.9 | Complete hydraulic system, including the pump and hoses, shall be factory assembled and mounted to the attenuator |
| 4.0 | Attenuator system steel support frame and strike plate shall be easily refurbishable and reusable after a typical design impact |
| 4.1 | Cartridges shall be a light weight aluminum type |
| 4.2 | Attenuator shall have the following performance criteria: |
| 4.3 | Attenuator, when mounted to a truck weighing up to 9,000kg (19,845lb) (actual weight) with automatic transmission in neutral and parking brakes locked, truck situated on clean dry pavement, shall perform as follows: |
| 4.4 | Attenuator shall have passed all tests required under ASHTO Report MASH(2016) TL 3-50 |
| 4.5 | Attenuator shall have passed all tests required under ASHTO Report MASH(2016) TL 3-51 |
| 4.6 | Attenuator shall have passed all tests required under ASHTO Report MASH(2016) TL 3-52 |
| 4.7 | Attenuator shall have passed all tests required under ASHTO Report MASH(2016) TL 3-53 |
| 4.8 | Attenuator shall have passed all tests required under ASHTO Report MASH(2016) TL 3-54 |
| 4.9 | To minimize potential damage to the shadow truck, no portion of the attenuator's energy absorbing elements shall protrude forward of the underride during impact. |
| 5.0 | To minimize the potential for secondary impacts, the exit velocity of the impacting vehicle (rebound) shall be no more than 5% of the incoming velocity |
| 5.1 | The Attenuator shall be capable of passing an accelerated endurance test, which duplicates anticipated shock loading the system may encounter in actual use. |
| END OF SPECIFICATION |
&14Attachment A6 2200000000
Sheet2
File details come from the government source that posted it. Updated .