B08_Attach_3_DOI_Shared_Specs_Part2.pdf

UNIFORM COMPONENT SPECIFICATIONS

OUTDOOR WORK VEST (Spec S043)

GENERAL DESCRIPTION

The Bureaus’ seek consistency of style and fit in the outdoor vest and this spec is an effort to standardize the style and fit.

The images provided below are the current images of each outdoor vest. Except for the color characteristics and customization indicated below, the outdoor vest for each Bureau should be consistent under this specification.

The garment is an insulated weight work vest.

PERFORMANCE/WORK ENVIRONMENT CHARACTERISTICS

• Worn as an inner or outer layer in an outdoor work environment

• The fit shall be comfortable and allow for be full range of motion to including bending

• The fabric weave shall be wind and water resistant

• The fabric shall be anti-microbial/odor resistant

• The fabric shall be stain and snag resistant

• The fabric should be machine washable

• The fabric shall be colorfast and resist fading, shrinking and pilling

• The zipper front closure shall extend from bottom hem up thru collar, with a storm flap

• The garment has two large front patch pockets at the bottom

• Unisex

COLOR CHARACTERISTICS

• Dark Brown – FWS

• Navy - BLM

STYLE CHARACTERISTICS

• Badge Tab: Reinforced with matching material and two centered reinforced eyelets for badge on left chest

• Name Plate: Reinforced with matching material and two centered reinforced eyelets for nameplate on right chest

• Hanger Loop: Should have a nylon or similar tape hanger loop sewn into the inside of the collar at center back

• Zipper: Should have a long pull-tab

• Collar: Should be a stand-up collar

CUSTOMIZATION CHARACTERISTICS

FWS:

• General Employee: Standard large FWS emblem on left chest.

• FWO: FWO badge emblem on left chest with options of plain back or FEDERAL OFFICER lettering with Fish & Wildlife Service lettering centered back

• Wildlife Inspector: Inspector badge emblem on left chest with options of plain back or

FEDERAL OFFICER lettering with Fish & Wildlife Service lettering centered back.

BLM – Small BLM patch attached to left front chest.

SIZE CHARACTERISTICS

Stock: Med XS - 4XL Long M - 3XL

Non-stock: Med XXS, 5XL and Long XXS, 4XL, 5XL

IMAGES

FWS – Outdoor Vest

BLM – There currently no image of a navy vest with customization.

INSULATED FLEECE LINED VEST (Spec S044)

The Bureaus’ seek consistency of style and fit in the fleece lined vest and this spec is an effort to

The images provided below are the currently available images of each fleece lined vest. Except for the color characteristics and customization indicated below, the fleece vest for each Bureau should be

This vest has two iterations, one with badge tabs (described below) and one without badge tabs. The garment is an insulated fleece vest.

• The fit shall be comfortable and allow for be full range of motion to including bending and reaching overhead

• The fabric weave shall be wind and water resistant

• The fabric shall be anti-microbial/odor resistant

• The fabric shall be stain and snag resistant

• The fabric shall be machine washable

• The fabric shall be colorfast and resist fading, shrinking and pilling

• The zipper front closure shall extend from bottom hem up thru collar

• Ranger Green – NPS, USACE

• Badge Tab: Reinforced with matching material and two centered reinforced eyelets for badge on left chest

• Name Plate: Reinforced with matching material and two centered reinforced eyelets for nameplate on right chest

• Pockets: Should have two front slash pockets, lined and with secure closures

• Hanger Loop: Should have a nylon or similar tape hanger loop sewn into the inside of the collar at center back

Stock: Med XS - 4XL

Long M - 3XL

NPS – Insulated Vest (shown without badge tab and name tab)

USACE – Fleece Lined Vest (shown with badge tab and name tab)

ALL FLEECE VEST (Spec S045)

The Bureaus’ seek consistency of style and fit in the fleece vest and this spec is an effort to standardize the style and fit.

The images provided below are the currently available images of each fleece vest. Except for the color characteristics and customization indicated below, the fleece vest for each Bureau should be consistent under this specification.

This vest has two iterations, one with badge tabs (described below) and one without badge tabs. The garment is fleece vest.

reaching overhead

• The fabric weave shall be wind and water resistant

• The fabric shall be anti-microbial/odor resistant

• The fabric shall be stain and snag resistant

• The fabric shall be machine washable

• The fabric shall be colorfast and resist fading, shrinking and pilling

• The zipper front closure shall extend from bottom hem up thru collar

• The vest shall conform to true male sizing

• The vest shall conform to true female sizing

• Black – FWS

• Navy – BLM

• Pockets: Should have two front slash pockets, lined and with secure closures

• Hanger Loop: Should have a nylon or similar tape hanger loop sewn into the inside of the collar at center back

FWS

• Left chest shall have standard small FWS emblem.

BLM

• Small BLM patch or heat seal logo on upper left chest

Male

• Stock: S-3XL; Long M-3XL

• Non-stock: XS, 3XL-5XL; Long L-5XL

Female

• Stock: S-2XL; Long M-2XL

• Non-stock: XXS-XS, 3XL-5XL; Long M-5XL

Male Female

FLEECE LINED JACKET (Spec S046)

The Bureaus’ seek consistency of style and fit in the fleece lined jacket and this spec is an effort to

The images provided below are the current images of each fleece lined jacket. Except for the color characteristics and customization indicated below, the fleece lined jacket for each Bureau should be

The garment is a fleece lined jacket. The fleece jacket is part of an integrated outerwear system that also includes a waist-length over shell jacket, a hip-length over shell jacket and a down parka.

The fleece lined jacket can be worn alone, or it can be zipped into the waist-length over shell jacket and a hip-length over shell.

This jacket has two iterations, one with badge tabs (described below) and one without badge tabs.

NPS - This uniform item is designated as a CORE item.

USACE – This uniform item is designated as a CORE item.

• Worn as an outer layer in an outdoor work environment

• Worn as a layer under/within other jackets in the integrated system.

• The fit shall be comfortable and allow for be full range of motion to including bending

• The fabric weave shall be wind and water resistant

• The fabric shall be anti-microbial/odor resistant

• The fabric shall be stain and snag resistant

• The fabric should be machine washable

• The fabric shall be colorfast and resist fading, shrinking and pilling

• The jacket shall conform to true male sizing

• The jacket shall conform to true female sizing

▪ Ranger Green – NPS, USACE

• Badge Tab: Optional - reinforced with matching material and two centered reinforced eyelets for badge on left chest

• Name Plate: Optional - reinforced with matching material and two centered reinforced eyelets for nameplate on right chest

• Pockets: Should have two front slash pockets, lined and with secure closures

• Sleeves: Should have a knit cuff at the wrist collar at center back

• Bottom: Should be a snug fit knitted waistband

• Zipper: The front zipper shall extend from bottom hem up thru collar

NPS, USACE - Appropriate agency patch sewn on center top of left sleeve

Stock: XS – 3XL

Non-stock: XXS, 4XL, 5XL

NPS – Fleece Jacket

USACE– Fleece Jacket

FLEECE LIGHT WEIGHT JACKET (Spec S047)

The Bureaus’ seek consistency of style and fit in the fleece jacket and this spec is an effort to

The images provided below are the current images of each fleece jacket. Except for the color characteristics and customization indicated below, the fleece jacket for each Bureau should be

• The fit shall be comfortable and allow for be full range of motion to including bending

• The fabric weave shall be wind and water resistant

• The fabric shall be anti-microbial/odor resistant

• The fabric shall be stain and snag resistant

• The fabric should be machine washable

• The fabric shall be colorfast and resist fading, shrinking and pilling

▪ Navy – FWS, BLM

▪ Black - FWS

Detail Design

• Fabric: 7.7 oz/260 gsm to 8 oz /265 gsm 100% Polyester, anti-pill

• Pockets: Two front lower zipper pockets, lined and with secure closures

• Sleeves: Knit or open cuff at the wrist

• Hanger Loop: Should have a nylon or similar tape hanger loop sewn into the inside of the collar at center back

• Bottom: Open or knitted waistband

• Zipper: Center front zipper shall extend from bottom hem up thru collar

• Collar: Fleece chin guard

FWS-Volunteer (Navy)

• The standard Volunteer log embroidered on the left chest.

FWS – SPO (Black)

• Large standard FWS Embroidered Logo on left chest.

BLM – General

• DOI rocker and large agency patch on center top of right and left sleeve;

▪ BLM triangle shall be below rocker with ½” distance between bottom center of the rocker and top of the BLM triangle

FWS – Volunteer

FWS- Special Purposed Ordering

Female

BLM – There are currently no images of male and female fit fleece jacket with customization.

FLEECE HEAVY WEIGHT JACKET (Spec S048)

The Bureaus’ seek consistency of style and fit in the fleece jacket and this spec is an effort to

The images provided below are the current images of each fleece jacket. Except for the color characteristics and customization indicated below, the fleece jacket for each Bureau should be

BLM - This uniform item is designated as a CORE item.

FWS – This uniform item is designated as a CORE item.

• The fit shall be comfortable and allow for be full range of motion to including bending

• The fabric weave shall be wind and water resistant

• The fabric shall be anti-microbial/odor resistant

• The fabric shall be stain and snag resistant

• The fabric should be machine washable

• The fabric shall be colorfast and resist fading, shrinking and pilling

▪ Brown – FWS, BLM, NPS

• Fabric Weight: 9.62 oz/sq yd

• Name Plate: Optional - reinforced with matching material and two centered reinforced eyelets for nameplate on right chest

• Pockets: Should have two front slash pockets, lined and with secure closures

• Sleeves: Knit or open cuff at the wrist

• Hanger Loop: Should have a nylon or similar tape hanger loop sewn into the inside of the collar at center back

• Bottom: Open or knitted waistband

• Zipper: The front zipper shall extend from bottom hem up thru collar

FWS- General Employees (Brown)

• The large standard FWS emblem shall be sewn on the left sleeve.

FWS-Wildlife Inspector (OLE) (Brown)

• The large standard FWS emblem shall be sewn on the right and left sleeves.

• The FWS OLE badge emblem shall be sewn on left chest.

BLM

• Law Enforcement

▪ Rocker and agency patch on upper top center of right and left sleeve;

▪ Ranger or Special Agent Law Enforcement badge on upper left front

▪ BLM triangle shall be below rocker with ½” distance between bottom center of the rocker and top of the BLM triangle

▪ Optional right chest direct embroidery name; first initial and last name or first and last name; tan thread

• Volunteer

▪ Small volunteer patch on upper left chest

▪ Embroider "VOLUNTEER" centered 1/4" below logo in blue PMS color 310

FWS - General

Inspector

BLM - Law Enforcement and Volunteer

Ranger Special Agent

Volunteer

APEX JACKET (Spec S049)

The Bureaus’ seek consistency of style and fit in the windbreaker and this spec is an effort to

The images provided below are the current images of each windbreaker. Except for the color characteristics and customization indicated below, the windbreaker for each Bureau should be

The garment is a windbreaker.

This garment has two iterations, one with badge tabs (described below) and one without badge tabs.

• The fabric weave shall be wind and water resistant

• The fabric shall be anti-microbial/odor resistant

• The fabric shall be stain and snag resistant

• The fabric should be machine washable

• The fabric shall be colorfast and resist fading, shrinking and pilling

• Badge Tab: Optional - reinforced with matching material and two centered reinforced eyelets for badge on left chest

• Name Tabs: Optional reinforced with matching material and two centered reinforced eyelets for nameplate on right chest

• Pockets: Should have two front pockets with secure closures, at minimum one zippered pocket in upper front

• Zippers: Side zippers should extend from the bottom hem to the under arm and be located mouth to mouth for two-way movement and access up and down

• Sleeves: Should have a mechanism for adjustable closing at the wrist cuff collar at center back

NPS - Agency patch sewn on center top of left sleeve. With and without badge and name tabs.

USACE - Agency patch sewn on center top of left sleeve. With badge and reinforced name tabs.

▪ Stock: XS – 3XL

▪ Non-stock: XXS, 4XL, 5XL

NPS

USACE

SOFT SHELL JACKET (Spec S050)

The Bureaus seek consistency of style in the work belt and this spec is an effort to standardize the style.

The images provided below are the currently available images of each Softshell Jacket. Except for the color characteristics and customization indicated below for each Bureau should be consistent under this specification.

BOR - This uniform item is designated as a CORE item.

• Perform in a mild climate from approximately 41° to 65°F

• The fit shall be durable, comfortable and 4-way stretch for full range of motion

• The fabric weave shall be wind and water resistant

• The fabric weave shall be breathable and possess moisture wicking capabilities

• The fabric shall be anti-microbial/odor resistant

• The fabric shall be stain and snag resistant

• The fabric should be machine washable

• The jacket shall conform to true male and female true sizing

• Navy - BOR, BSEE, BLM

Component

Unisex – BSEE and BOR

Male and Female - BLM

• Waterproof 8,000 to 10,000 mm

• Breathability 10,000 g/mm²

• Wind resistant 10 CFM to 5 CFM

• UPF 35+

• 4-way stretch fabric

• Fleece or microfleece lined

• Two front lower side zippered pockets

• One to two chest zipper exterior pocket,

• Two interior zipper or velcro pockets

• One to two sleeve pockets

• Full zip through stand-up storm flap collar with chin guard

• Hem/Bottom - open, drawstring or elastic

• Cuffs – open, velcro, snap or elastic

• Female fit should have longer length than male style

BSEE

• BSEE logo on upper left chest

• Employee name will be embroidered on right chest.

• American flag on left shoulder

• DOI Patch on right sleeve

BOR

• Reclamation Logo VWhite Embroidered Front Right Chest

• Rocker and agency patch on upper top center of right and left sleeve

• BSEE and BOR – Unisex

• BLM - Male and Female

Male sizing S - 5XL

Female sizing XS - 3XL

BSEE

BOR - Unisex

BLM – There currently are images of a navy male or female softshell jacket with customization.

NYLON WINDBREAKER (Spec S051)

The Bureaus’ seek consistency of style and fit in a wind and water-resistant and this spec is an effort to

• Worn in year-round indoor and outdoor work environment

• Wind, water and abrasion resistant

• The fit shall be comfortable and allow for full range of motion to include bending, reaching, climbing, squatting without coming apart at the seams

• Roll away hood with rain bill

▪ Brown – BLM, FWS

▪ Navy – BOR, BLM, FWS

Components

• 100% nylon taslan shell with polyurethane coating

• 100% polyester taffeta lining in sleeves

• Roll away hood with rain bill

• Front zipper closure

• Center front/lower pockets

• Law Enforcement - Brown

▪ Large law enforcement badge (Ranger or Special Agent) on upper front left chest

▪ Corresponding language on the center back POLICE US RANGER (Ranger badge) OR

POLICE US AGENT (Special Agent badge).

• Volunteer - Brown

▪ Small BLM Volunteer heat seal or patch on upper left chest.

▪ Embroider “VOLUNTEER” centered ¼” below logo in blue PMS color 310

• General – Navy

▪ DOI rocker and large agency patch on center top of right and left sleeve;

▪ Top of rocker shall be 1” below sleeve seam

▪ BLM triangle shall be below rocker with ½” distance between bottom center of the rocker and top of the BLM triangle

FWS

• Wildlife Inspectors

▪ Standard large FWS emblem on center top of right and left sleeves.

▪ Standard OLE Inspector emblem on upper front left chest.

▪ FEDERAL OFFICER lettering on center back with Fish and Wildlife Service underneath it tan.

• General Employee

▪ Standard large FWS emblem on center top of left sleeve.

• Volunteers

▪ Standard large FWS Volunteer emblem on center top of right sleeve.

• Reclamation VWhite Logo embroidered on front left chest

Unisex

▪ Stock: XS-4XL

Law Enforcement

General

BLM - Unisex

FWS - OLE Inspectors

FWS - General

FWS - Volunteer

WAIST LENGTH OVER SHELL JACKET WITH DETACHABLE HOOD (Spec S052)

The Bureaus seek consistency of style and fit in the waist length over shell and this spec is an effort to

The images provided below are the currently available images of each waist length over shell. Except for the color characteristics and customization indicated below, the waist length over shell for each

Bureau should be consistent under this specification.

The garment is a waist length over shell with a detachable non-insulated hood. The waist length over shell is part of an integrated outerwear system that also includes a hip-length over shell jacket, a fleece jacket, and a down parka.

This over shell can be worn alone or the fleece jacket or the down parka can be zipped in as a liner.

• The garment shall be fully lined and uninsulated

• The garment shall have a front storm flap, a two-way zipper with outer snap closures and an adjustable waist cord

• The garment shall have adjustable side vents for radio and pants pocket access

• The fabric weave shall be wind and water resistant

• The fabric shall be anti-microbial/odor resistant

• The fabric shall be stain and snag resistant

• The fabric should be machine washable

• The fabric shall be colorfast and resist fading, shrinking, and pilling

• The front zippers shall be located mouth to mouth for two-way movement and access up and down

• The hood shall be detachable

• The fabric shall be GORE-TEX or equivalent

▪ Dark Brown – FWS, BLM on left chest

• Name Tab: Reinforced with matching material and two centered reinforced eyelets for nametag on right chest

• Drawstring: Concealed drawstring tunnel at the waistline, beginning and ending at the zipper tape/weather flap seams.

• Pockets: Should have hand-warmer slash pockets on the front, at minimum one zippered patch pocket inside the breast and pockets in the side seams with secure closures

• Zippers: Shall have double sliders with long tabs and close with storm flaps

• Sleeves: Should be fully lined with a mechanism for adjustable closing at the wrist cuff

• Hanger Loop: Should have a nylon or similar tape hanger loop sewn into the inside of the collar at center back

• Hood: Lined, non-insulated matching fabric with visor, drawstring front closure with cord locks and snap front closure, and snap attachments to matching placement on over shell

• Part of integrated outwear system (waist length over shell, fleece jacket and down parka)

NPS, USACE - The appropriate agency patch sewn centered onto top of left sleeve.

BLM - Law Enforcement

• Left and right sleeve shall have DOI rocker and large BLM triangle patch

▪ Top of rocker shall be 1” below sleeve seam

▪ BLM triangle shall be below rocker with ½” distance between bottom center of the rocker and top of the BLM triangle

• Left chest

▪ Official BLM small Ranger or Special Agent badge centered above pocket

• Right chest

▪ Optional direct embroidery, tan thread

▪ First initial and last name, all caps

FWS – General Employee

• Standard large FWS emblem on left sleeve FWO and Wildlife Inspector

• Standard large FWS emblem on right and left sleeve

• FWO or Inspector standard badge emblem on left chest

USACE - The detachable hood is included with the jacket

The detachable hood is sold separately for NPS, FWS and BLM.

Stock: XS - 3XL

NPS – Waist Length Shell (System)(shown with badge tab and name tab)

USACE *There is currently no image of the USACE waist length over shell. The USACE waist length over shell should be the same style as the other waist length over shells, with appropriate customization and available in Ranger green.

FWS- General Employee

FWS Law Enforcement

HIP LENGTH OVER SHELL JACKET WITH DETACHABLE HOOD (Spec S053)

The Bureaus’ seek consistency of style and fit in the hip length over shell and this spec is an effort to

The images provided below are the currently available images of each hip length over shell. Except for the color characteristics and customization indicated below, the hip length over shell for each Bureau should be consistent under this specification.

The garment is a hip length over shell with a detachable non-insulated hood. The hip length over shell is part of an integrated outerwear system that also includes a waist-length over shell jacket, a fleece jacket and a down parka.

This over shell can be worn alone or the fleece jacket or the down parka can be zipped in as a liner.

• The garment shall be fully lined and uninsulated

• The garment shall have front storm flaps, a front two way zipper with outer snap closures and an adjustable waist cord

• The garment shall have adjustable side vents for radio and pants pocket access

• The fabric weave shall be wind and water resistant

• The fabric shall be anti-microbial/odor resistant

• The fabric shall be stain and snag resistant

• The fabric should be machine washable

• The fabric shall be colorfast and resist fading, shrinking and pilling

• The front zippers shall be located mouth to mouth for two way movement and access up and down

• The vent zipper at side seam shall allow access to radio or other items on belt

• The hood shall be detachable

• Dark Brown –FWS, BLM, NPS on left chest

• Name Plate: Reinforced with matching material and two centered reinforced eyelets for nametag on right chest

• Drawstring: Concealed drawstring tunnel at the waistline, beginning and ending at the zipper tape/weather flap seams.

• Pockets: Should have hand-warmer slash pockets on the front, at minimum one zippered patch pocket inside the breast and pockets in the side seams with secure closures

• Side Vents: Should be closed with an inseam zipper

• Zippers: Shall have double sliders with long tabs and storm flaps

• Sleeves: Should be fully lined with a mechanism for adjustable closing at the wrist cuff

• Hanger Loop: Should have a nylon or similar tape hanger loop sewn into the inside of the collar at center back

• Hood: Lined, non-insulated matching fabric with visor, drawstring front closure with cord locks and snap front closure, and snap attachments to matching placement on over shell

NPS, USACE - The appropriate agency patch sewn centered onto top of left sleeve.

NPS - Brown version requires no customization

FWS- General Employees

• The large standard FWS emblem shall be sewn on the left sleeve.

FWS-Wildlife Inspector (OLE)

• The large standard FWS emblem shall be sewn on the right and left sleeves.

• The FWS OLE badge emblem shall be sewn on left chest.

▪ Optional: FEDERAL OFFICER Lettering with FISH & WILDLIFE SERVICE beneath it on center back of garment.

• Top of rocker shall be 1” below sleeve seam

• BLM triangle shall be below rocker with ½” distance between bottom center of the rocker and top of the BLM triangle

• Left chest

▪ Official BLM small Ranger or Special Agent badge centered above pocket

• Right chest

▪ First initial and last name, all caps

The detachable hood is sold separately.

NPS – Hip Length Shell (System)(shown with badge tab and name tab)

FWS – Hip Length Shell (System)

BLM – Law Enforcement

Ranger

Special Agent

HIP LENGTH PARKA WITH DETACHABLE INSULATED HOOD (Spec S054)

The Bureaus seek consistency of style and fit in the hip length parka with detachable insulated hood and this spec is an effort to standardize the style and fit.

The images provided below are the currently available images of each hip length parka with detachable insulated hood. Except for the color characteristics and customization indicated below, the hip length parka with detachable insulated hood for each Bureau should be consistent under this specification.

The garment is a hip-length parka with a detachable insulated hood.

USACE – This uniform item is designated as a CORE item.

• The fit shall be comfortable and allow for be full range of motion to include bending

• Parka shall be fully lined and insulated

• Parka shall have a front storm flap and a two-way zipper with outer snap closures and an adjustable waist cord with cord locks

• The fabric weave shall be wind and water resistant

• The fabric shall be anti-microbial/odor resistant

• The fabric shall be stain and snag resistant

• The fabric should be machine washable

• The fabric shall be colorfast and resist fading, shrinking and pilling

• Front zippers shall be located mouth to mouth for two-way movement and access up and down

• The vent zipper at side seam shall allow for access to radio or other items on belt

• The hood shall be insulated and detachable

• Ranger Green - USACE (requires badge and name tabs)

• Dark Brown – BLM (NO badge and name tabs) on left chest

• Name Tab: Reinforced with matching material and two centered reinforced eyelets for nametag on right chest

• Drawstring: Should have a concealed drawstring tunnel at the waistline, beginning and ending at the zipper tape/weather flap seams

• Cuffs and Collar: Should be knitted cuff sewn into the lining/outer seam

• Pockets: Should have hand-warmer slash pockets on the front, at minimum one zippered patch pocket inside the breast and pockets in the side seams with secure closures

• Lining: should be sewn into the insulation batting to prevent rolling and bunching

• Side Vents: Should be closed with an inseam zipper

• Zippers: Shall have double sliders with long tabs and storm flaps

• Sleeves: Should be fully lined

• Hanger Loop: Should have a nylon or similar tape hanger loop sewn into the inside of the collar at center back

• Hood: Lined and insulated matching fabric with visor, drawstring front closure with cord locks and snap front closure, and snap attachments to matching placement on parka included.

• Agency patch sewn centered onto top of left sleeve.

• USACE requires badge and name tabs.

• No badge or name tabs

• Left and right sleeve shall have DOI rocker and large BLM triangle patch

▪ Top of rocker shall be 1” below sleeve seam

▪ BLM triangle shall be below rocker with ½” distance between bottom center of the rocker and top of the BLM triangle

• Left chest

▪ Official BLM small Ranger or Special Agent badge centered above pocket

• Right chest

▪ First initial and last name, all caps, font Roboto

USACE – Hip Length Parka with Hood (shown with badge and name tabs)

UNIFORM COMPONENTS SPECIFICATIONS

DOWN PARKA/LINER (Spec S055)

The Bureaus’ seek consistency of style and fit in the down parka/liner and this spec is an effort to

The images provided below are the currently available images of each down parka/liner. Except for the color characteristics and customization indicated below, the down parka/liner for each Bureau should be consistent under this specification.

The Garment is a Down parka with two front, zippered pockets.

The down parka is part of an integrated outerwear system that also includes a fleece jacket, a waist-length over shell jacket and a hip-length over shell.

The down parka can be worn alone, or it can be zipped into the waist-length over shell and a hip-length over shell jackets as a liner.

The parka/liner has two iterations, one with badge tabs (described below) and one without badge tabs.

• Worn to perform physical work primarily outdoors

• The fit shall be comfortable and allow for full range of motion

• The fabric weight shall be suitable extreme cold climates

• The fabric shall be machine-washable

• The fabric shall resist fading

• The fabric shall resist stains

• The fabric shall be wrinkle resistant

• Ranger Green- NPS

• Dark Brown- FWS, BLM

• Basic Material: Basic Material: The material should be Ranger green, taslan nylon, with nylon lining, nylon scrim with 1 oz. urethane coat, DWR between body fabric and insulation (to both sides of insulation), Ranger Green. The fill should be goose down.

• Thread: All thread should be minimum size 60/36.

• Zipper: The front zipper should be a separating 1-way zipper with reversible pull DTM body.

The (2) front pocket and (1) inner pocket zippers should be non- separating 1-way zipper with reversible pull DTM body. Each zipper should have an additional zipper pull. The end should be made of rubber, and the cord should be made of nylon. The color should be black.

General Instructions

• Stitching: A chainstitch of 6 to 7 stitches per inch should be used for basting the garment. A chainstitch of 8 stitches per inch should be used for sewing the garment together. A lockstitch should be used for quilting the lining.

• Front: The fronts should have one-way zipper closure from the top of the collar to the bottom edge. The front zipper should be 25” long. The front raw edges of shell and liner should be serged to the zipper tape. The slider should finish on the right front. The zipper should be topstitched 1/8” gauge.

• Back: The back should be 2 piece raglan style. It should also have a male snap centered 1” below the collar (for compatibility w/ over-shell).

• Collar: The collar should be 3 ½” high at the fronts and 3” high at center back. The collar front edges should align with the jacket fronts. The collar should be lined with same fabric and top edge stitched 1/16” gauge.

• Pockets: The front slash zipper pockets shall have 6 1/2” openings. The bottom of the opening shall be 4” from the side seam. The top of the opening shall be 6” from the side seam. The slash opening should be folded back and stitched to the zipper tapes with 1/16” topstitching. Pocket layers should consist of two layers of nylon.

• Sleeves: The sleeves should be one piece, raglan style construction. The bottom of the sleeves should be finished with a flared knit cuff 3” wide.

• Bottoms: The jacket bottom should be finished with a 1” DT hem to create a self fabric tunnel.

• Name Plate Tab and Badge Tab: This item should be made available in versions with name plate tab and badge tab and without name plate tab and badge tab. Name plate and badge tabs should consist of self fabric, and ends should be turned under ¼” and backtacked down 1/16” from edges. The name plate tab should be placed on the outside of the jacket on the right upper front.

The badge tab should be placed on the outside of the jacket on the left upper front.

NPS Patch:

• Agency patch should be sewn on left sleeve 9 1/2” down from neck seam. The patch should be sewn with inconspicuous stitching using thread closely matching the emblem background color.

FWS- General Employees

• The large standard FWS emblem shall be sewn on the left sleeve.

FWS-Fish and Wildlife Officer (FWO)

• The large standard FWS emblem shall be sewn on the right and left sleeves.

• The FWS FWO badge emblem shall be sewn on left chest.

FWS-Wildlife Inspector (OLE)

• The large standard FWS emblem shall be sewn on the right and left sleeves.

• The FWS OLE badge emblem shall be sewn on left chest.

• Left and right sleeve shall have DOI rocker and large BLM triangle patch

▪ Top of rocker shall be approximately 9 ½" down from neck seam

▪ BLM triangle shall be 1/2'” below rocker

▪ BLM triangle shall be below rocker with ½” distance between bottom center of the rocker and top of the BLM triangle

• Left chest

▪ Official BLM small Ranger or Special Agent badge centered above pocket

▪ The patch should be sewn with inconspicuous stitching using thread closely matching the emblem background color

• Right chest

▪ First initial and last name, all caps, font Roboto

Stock:

• Regular: XS – 4XL

• Long: M – 3XL

Non-Stock

• Regular XXS, 5XL

• Long S, 4XL

NPS –Image shown without badge and name tabs

FWS Law Enforcement- FWO & OLE

BLM – Law Enforcement

TACTICAL SYSTEM JACKET W/LINER AND HOOD (Spec S___)

The Bureaus’ seek consistency of style and fit in the Tactical System Jacket with liner and hood and this spec is an effort to standardize the style and fit.

The images provided below are the currently available images. Except for the color characteristics and customization indicated below, the jacket for each Bureau should be consistent under this specification.

The jacket is an integrated outerwear system that also includes a waist-length over shell jacket and a hip-length over shell and hood.

The jacket can be worn alone, or it can be zipped into the waist-length over shell and a hip-length over shell jackets as a liner.

• Worn to perform physical work primarily outdoors

• The fabric weight shall be suitable extreme cold climates

• The fabric shall be machine-washable

• The fabric shall resist fading

• The fabric shall resist stains

• The fabric shall be wrinkle resistant

• Ranger Green- BOR, NPS

• The outershell 100% water poof, breathable, wind resistant nylon; softshell zip out water and wind resistant exterior and warm, brushed fleece; hood removable and packable when not in use.

• Agency logo embroidered one inch below shoulder seam centered on left arm of both outer and inner jackets

• Agency patch sewn on center top of left sleeve

• Regular: XS – 4XL

• Long: M – 3XL

BOR - Unisex:

RAINCOAT (Spec S056)

The Bureaus’ seek consistency of style and fit in the raincoat and this spec is an effort to standardize

The images provided below are the currently available images of each raincoat. Except for the color characteristics and customization indicated below, the raincoat for each Bureau should be consistent

The garment is a full-length caped raincoat.

• Worn as an outer layer in an outdoor ceremony and work environment

• The fit shall be comfortable and allow for be full range of motion to include bending

• The fabric weave should be wind resistant

• The fabric shall be waterproof

• The fabric shall be anti-microbial/odor resistant

• The fabric shall be stain and snag resistant

• The fabric shall be colorfast and resist fading, shrinking, and pilling

• The fabric should be a lightweight material

▪ Ranger Green - NPS, USACE

▪ Black with Hood – BOR

• Badge Tab: Reinforced with matching material and two centered reinforced eyelets for badge on left chest

• Name Tab: Reinforced with matching material and two centered reinforced eyelets for nametag on right chest

• Sleeves: Should be raglan style

• Cape: Should have a mesh panel under the cape for breathability. Cape should cover the shoulder area on the back of coat and be sewn into the top of the sleeve seam

NPS and USACE - Agency patch sewn centered onto top of left sleeve.

BOR - Reclamation White logo embroidered on front left chest

NPS – Image is for customization only

USACE - Image is for customization only

HIP LENGTH WORK JACKET WITH PERMANENT LINER (Spec S057)

The garment is a 100% cotton, 10oz duck cloth work jacket.

reaching

• The fabric weight shall be suitable for all weather conditions

• The fabric shall be stain and snag resistant

• The fabric should be machine washable

• The fabric shall be colorfast and resist fading, shrinking, and pilling

• Pockets: Should have two front slash pockets at the sides, lined and with secure closures.

The front should also have two plain, mitered breast pockets with scalloped flaps and buttonholes, with corresponding buttonholes on the pockets. The left pocket should also have a pencil slot/pocket.

There should be one interior pocket on the left side.

• Sleeves: Should have a straight cuff closed with a button and corresponding buttonhole at the wrist

• Lining: Should have a permanent synthetic fabric lining for the body and the sleeves

• Zipper: The front zipper shall extend from bottom hem to the neck and be covered with a storm flap with metal snaps for closure

NPS and USACE: Appropriate agency patch sewn on center top of left sleeve

BLM - General

• Left and right sleeve shall have rocker and large BLM triangle patch

• Body Length Size

• Short - XS-M

• Regular - XS-2XL

• Long -L-2XL

NPS – Work Jacket

USACE – Work Jacket

BLM – There currently are no images of navy with customization.

WORK DUCK JACKET (Spec S058)

The garment shall be a 100% cotton dark brown duck work jacket with hood.

reaching

• The fabric weight shall be suitable for all weather conditions

• The fabric shall wind resistant

• The fabric should be machine washable

• Brown – FWS

• 100% cotton premium duck

• Quilted polyester insulation lining

• Triple stitched seams

• Brass zipper and rivets at stress points

• Attached hood with drawstrings

• Two chest front hand-warmer pockets and two front scoop pockets

• Inside pocket and media pockets

• Pencil pocket on sleeve

• Rib knit waist and cuffs

▪ Top of rocker shall be 1” below sleeve seam

▪ BLM triangle shall be below rocker with ½” distance between bottom center of the rocker and top of the BLM triangle

• General Employee

▪ Standard large FWS emblem shall be sewn on left sleeve.

• FWO – Law Enforcement

▪ Standard large FWS emblem shall be sewn on right and left sleeves

▪ FWO LE Badge on left chest

▪ Optional: “FEDERAL OFFICER” lettering with FISH & WILDLIFE SERVICE beneath it on center back of garment

• Wildlife Inspector- Law Enforcement

▪ Standard large FWS emblem shall be sewn on right and left sleeves

▪ Wildlife Inspector Badge emblem left chest

▪ Optional: “FEDERAL OFFICER” lettering with FISH & WILDLIFE SERVICE beneath it on center back of garment

▪ Regular Small-5XL

▪ Tall Medium – 5XL

• Maintain stock and non-stock size range

BLM - There currently is no image of a navy duck jacket with agency customization.

FWS: FWO

FWS: Wildlife Inspector

HOODED SWEATSHIRT (Spec S059)

The garment is a basic hooded sweatshirt with full zip closure.

• Worn in an indoor and outdoor work environment

• The fabric weight shall be suitable for an indoor and outdoor environment

• The fabric shall be machine-washable

• The fabric shall be colorfast and resist fading

• The fabric shall resist stains

• Garment shall have full front zipper closure and pockets

• Brown – BLM

• Navy – BLM, BOR

• Red – USACE

• Ranger Gray - NPS

• Pockets: Should have split muff pocket on lower front

• Collar and Sleeve Welts: Rib knit dyed to match shirt color

• Cotton/Polyester Blend

• Rib-knit cuffs and waistband with spandex

• Unlined hood with matching drawstring

• Split front pouch pocket

• Metal front full zipper

General - Navy

• Left and right sleeve shall have rocker and large BLM triangle patch

Fire & Aviation – Navy

• Small BLM patch added on front center of the cap with ‘FIRE” embroidered ¼” above patch in red thread

Volunteer – Brown

• Small BLM patch added on front center of chest.

• Embroider “VOLUNTEER” centered ¼” below the patch in blue PMS 310.

USACE

• Volunteer patch shall be sewn centered on upper left chest

BOR

• Reclamation HWhite logo embroidered on front left chest

• Agency patch sewn on center top of left sleeve

SIZES

• Unisex S-5XL

General – There currently is no image of navy with general customization.

Fire and Aviation Volunteer

NPS – There currently is no image of ranger gray with customization.

SERVICE DRESS “IKE” JACKET (Spec S060)

The Bureaus seek consistency of style and fit in the Service Dress “Ike” Jacket and this spec is an effort to standardize the style and fit.

The images provided below are the currently available images of each Service Dress “Ike” Jacket.

Except for the color characteristics and customization indicated below, the Service Dress “Ike” Jacket for each Bureau should be consistent under this specification.

The garment is a Service Dress Jacket in both male and female.

An Eisenhower-style jacket with zipper front and one-piece back, rolled collar with peak lapels, two front patch pockets pleated with scalloped flaps, regular coat sleeves, and knit inserts at bottom of each side over hip.

• Worn as an outer layer in a ceremonial, court, political, media or other formal setting

• The fabric shall be anti-microbial/odor resistant

• The fabric shall be stain and snag resistant

• The fabric shall be colorfast and resist fading, shrinking and pilling

• Ranger Green - NPS, USACE

STYLE CHARACTERISTICS MALE FIT

• Basic Material: Material shall be Raeford Style 646-168 or equal. Shade to be Ranger green.

Elastique weave, 16 - 16 ½ oz. per linear yard. 55% Polyester/45% Wool. Fusible Interlinings:

N/A.

• Linings: The coat shall be fully lined. The material for lining fronts, sleeves, pocket, flaps and back shall be Rayon lining, 3.7 ounce, color black, conforming to Class 1 of current issue of

Military Specification MIL-C-368.

• Thread: All thread, except #8 cotton gimp for buttonhole reinforcement, shall be cotton-covered polyester conforming to ticket numbers 70-2 ply 50-2 or 3 ply, and 30-2 or 3 ply of

MIL-T-43548. Color of all thread shall be dyed to match shade of self-fabric.

• Buttons: A 24 ligne bronze NPS Waterbury button or equal shall be inserted in each eyelet and fastened on the back side with a ring.

• Zipper: A Talon # 42 or equal zipper shall extend from bottom of lapel to bottom edge of front. Zipper shall be brass, separating style, with brass slides. Zipper tape shall be a polyester/cotton blend fabric dyed to match basic material. Zipper length shall vary according to body length or jacket.

• Knitted band insert: Waistband insert shall be 2x2 ply rib ½ cardigan of 93% nylon/ 7% elastic. The shade shall be dyed to match outer fabric. It shall measure 4” wide by 2 7/8” high and shall start at the side seam over the hip to the back.

• Shoulder Pads: Style #7, weight 1/2 ounce/pair of pads of 1/4 ounce/pad. Size: Neck to shoulder, 4 ¼”; armhole to armhole as wrapped around shoulder, 9 ¼”. Content: Polyester foam.

• Labels: See general reference and requirements sheet.

• Cutting: N/A.

• Stitching: All seaming and stitching of jacket shall use ticket number 30 or 50 except that overedging stitching may use ticket number 70-2 ply.

• Buttonholes: A buttonhole shall be centered ½” from center point tip of pocket flap and shall be an uncut eyelet end, square bar type.

• Front: One-piece fronts with a chest patch pocket on each side. Zipper to extend from bottom of lapel to bottom edge of front. Front edges to be topstitched ¼”. Facings shall be of basic material and cut in one piece. Front facing shall extend from neckline seam to bottom and shall be no less than 5” at top, tapering to no less than 3” at the bottom.

• Collar: Collar shall be one piece of basic material, having an inter liner of a good quality collar canvas that shall be padded to the felt undercollar. Collar and lapels shall be symmetrical in shape and be uniform in shape and size. Collar shall measure 1 5/8” from roll line at center back and 2” at notch. The lapels shall measure 4” at notch point and taper down to top of zipper. The collar shall cover the neck seams, fit the neck without caving in or sagging over shoulders, and fit the front shoulders neatly without looseness or folds under the collar. Collar and lapels shall be topstitched ¼” from the edge.

• Pocket Flaps: Front pocket flaps shall be constructed from basic material and lined with the

3.7-ounce Rayon lining fabric. Flaps, topstitched 3/16”, are to be 3-pointed style 5 ¾” wide, 2

¼” at side points, and 3” at center points. Top of flap shall be located ½” above top of pocket.

A male snap component shall be located under each side point and shall be fastened to the lining and not show on the outside of the flap. Snaps shall not be sewn on.

• Pockets: Two outside breast pleated patch pockets are made of self-material. Box pleat of pocket shall be 1 ½” wide and sewn down to prevent spreading. Pockets shall be 5 5/8” wide by

6” deep with rounded corners at the bottom. The pocket shall be lined with the 3.7-ounce

Rayon lining fabric. Pocket closure shall be by two 3/8” snaps located to correspond with male snaps on flap. Pocket shall be topstitched 3/16” from edge. One piped slash pocket shall be located under right front and sewn into the jacket lining. The pocket shall be constructed from the 3.7-ounce Rayon lining fabric and shall finish 5 ½” wide and 6” deep.

• Sleeves: The two-piece sleeve shall be set and joined with fullness properly distributed over the sleeve head and shall hang uniformly straight. Cloth sweat shields of basic material shall have edges piped with good quality Rayon binding. Sweat shields shall be stitched down all around.

Sleeves shall be hand felled at top half of armhole and machine stitched at bottom half. Sleeves shall be fully lined with the 3.7-ounce Rayon lining fabric with a 1½” minimum turn under at the bottom of the sleeve.

• Badge Reinforcement: Black enameled badge holder, Waterbury No. 9705, or equal, shall be placed above the left pocket flap, centered, and sewn on by hand. Base of holder shall be ½” above top of pocket flap.

• Bottom: Bottom lining hem shall be turned under not less than 5/8” and securely stitched.

Lining shall not be visible on outside of jacket. The self-goods turned up at the bottom of the jacket shall be a minimum of 2 1/2”.

• Lining: The seam allowance of the lining shall be tacked to corresponding side seam and sleeve seam allowances of the coat.

• NPS - National Park Service arrowhead shoulder patch shall be sewn on securely in the center of the left sleeve with the top edge 1 ¼” to 1 ½” below the shoulder seam depending on the garment size. The patch shall be sewn with inconspicuous stitching using brown thread closely matching the emblem background color.

• USACE - The Corps of Engineers ensign shoulder patch shall be sewn securely in the center of the left sleeve with the top edge 1 ½” below the shoulder seam. The patch shall be sewn with inconspicuous stitching using white thread to match the emblem background color. Red around red border.

Short 38-44, 50 Standard

34 and 46 Non-Standard

Regular 38-54 Standard, 34 Non-Standard

Long 38-56 Standard

X-long 40-54 Standard

NPS/USACE Male Ike Jacket

Size 34 36 38 40 42 44 46 48 50 52 54 56

Chest 40 42 44 46 48 50 52 54 56 58 60 62

Back Length

Short * * * * * * * *

RG * * * * * * * * * * *

Long * * * * * * * * * *

X- Long

STYLE CHARACTERISTICS FEMALE FIT

• Basic Material: Material shall be Raeford Style 646-168 or equal. Shade to be Ranger green.

Elastique weave, 16 - 16 ½ oz. per linear yard. 55% Polyester/45% Wool.

• Fusible Interlinings: N/A.

• Linings: The coat shall be fully lined. The material for lining fronts, sleeves, pocket, flaps and back shall be Rayon lining, 3.7-ounce, color black, conforming to Class 1 of current issue of

Military Specification MIL-C-368.

• Thread: All thread, except #8 cotton gimp for buttonhole reinforcement, shall be cotton-covered polyester conforming to ticket numbers 70-2 ply 50-2 or 3 ply, and 30-2 or 3 ply of

MIL-T-43548. Color of all thread shall be dyed to match shade of self-fabric.

• Buttons: A 24 ligne bronze NPS Waterbury button or equal shall be inserted in each eyelet and fastened on the back side with a ring.

• Zipper: A Talon # 42 or equal zipper shall extend from bottom of lapel to bottom edge of front.

Zipper shall be brass, separating style, with brass slides. Zipper tape shall be a polyester/cotton blend fabric dyed to match basic material. Zipper length shall vary according to body length or jacket.

• Knitted band insert: Waistband insert shall be 2x2 ply rib ½ cardigan of 93% nylon/ 7% elastic. The shade shall be dyed to match outer fabric. It shall measure 4” wide by 2 7/8” high and shall start at the side seam over the hip to the back.

• Shoulder Pads: Style #7, weight 1/2 ounce/pair of pads of 1/4 ounce/pad. Size: Neck to shoulder, 4”; armhole to armhole as wrapped around shoulder, 8”. Content: Polyester foam.

• Labels: See general reference and requirements sheet.

• Cutting: N/A.

• Stitching: All seaming and stitching of jacket shall use ticket number 30 or 50 except that overedging stitching may use ticket number 70-2 ply.

• Button Holes: A buttonhole shall be centered ½” from center point tip of pocket flap and shall be an uncut eyelet end, square bar type.

• Front: One piece fronts with a chest patch pocket on each side. Zipper to extend from bottom of lapel to bottom edge of front. Front edges to be topstitched ¼”. Facings shall be of basic material and cut in one piece. Front facing shall extend from neckline seam to bottom and shall be no less than 5” at top, tapering to no less than 3 1/2” at the bottom.

• Darts: Shall be formed by cutting a small notch in the top of front panel and sewing it back together. Dart shall begin in the shoulder seam and follow the breast line to approximately the center of the top pocket.

• Collar: Collar shall be one piece of basic material, having an interliner of a good quality collar canvas that shall be padded to the felt undercollar. Collar and lapels shall be symmetrical in shape and be uniform in shape and size. Collar shall measure 1 5/8” from roll line at center back and 2” at notch. The lapels shall measure 3 ½” at notch point and taper down to top of zipper. The collar shall cover the neck seams, fit the neck without caving in or sagging over shoulders, and fit the front shoulders neatly without looseness or folds under the collar. Collar and lapels shall be topstitched ¼” from the edge.

• Pocket Flaps: Front pocket flaps shall be constructed from basic material and lined with the

3.7 ounce Rayon lining fabric. Flaps, topstitched 3/16”, are to be 3 pointed style 5 ½” wide, 2

½” at side points and at center points. Top of flap shall be located ½” above top of pocket. A male snap component shall be located under each side point and shall be fastened to the lining and not show on the outside flap. Snaps shall not be sewn on.

• Pockets: Two outside breast pleated patch pockets of self-material. Box pleat of pocket shall be 1 3/8” wide and sewn down to prevent spreading. Pockets shall be 5 ¼” wide by 6” deep with rounded corners at the bottom. The pocket shall be lined with the 3.7 ounce Rayon lining fabric. Pocket closure shall be by two 3/8” snaps located to correspond with male snaps on flap.

Pocket shall be topstitched 3/16” from edge. One piped slash pocket shall be located under left front and sewn into the jacket lining. The pocket shall be constructed from the 3.7 ounce Rayon lining fabric and shall finish 5” wide and 5 ½” deep.

• Sleeves: The two piece sleeve shall be set and joined with fullness properly distributed over the sleeve head, and shall hang uniformly straight. Cloth sweat shields of basic material shall have edges piped with good quality Rayon binding. Sweat shields shall be stitched down all around.

Sleeves shall be hand felled at top half of armhole and…