B08-Attach_11-307127_YELL_Rehab_Ft_Yellowstone_Exteriors_Final_CD_Product_File.pdf

National Park Service

Yellowstone National Park

307127 YELL Rehabilitate Exteriors of

Historic Fort Yellowstone buildings

Product File

Construction Documents

02 May 2023

Table of Contents

(All Specifications sections from Divisions 2-32 are included - Not all sections include products)

Division 2 Existing Conditions

022119 Utilities Surveys

024100 Site Demolition

024119 Selective Demolition

Division 3 Concrete

030100 Maintenance of Concrete

033000 Cast-in-Place Concrete

034816 Precast Architectural Concrete

Division 4 Masonry

040300 Historic Treatment of Masonry

Division 5 Metals

050300 Historic Treatment of Decorative Metals

051200 Structural Steel Framing

055000 Metal Fabrications

055213 Pipe and Tube Railings

Division 6 Wood, Plastics, and Composites

060312 Historic Wood Repair

061000 Rough Carpentry

061600 Sheathing

061800 Glue Laminated Construction

062000 Finish Carpentry

Division 7 Thermal and Moisture Protection

071300 Sheet Waterproofing

072100 Thermal Insulation

072500 Weather Barriers

073116 Metal Shingles

073129 Wood Shingles and Shakes

073213 Clay Roof Tiles

076200 Sheet Metal Flashing and Trim

077200 Roof Accessories

079200 Joint Sealants

Division 8 Openings

080314 Historic Treatment of Wood Doors

080352 Historic Treatment of Wood Windows

081433 Stile and Rail Wood Doors

087100 Door Hardware

088000 Glazing

Division 9 Finishes

090391 Historic Treatment of Plain Painting

092116 Gypsum Board Assemblies

Division 26 Electrical

260010 Supplemental Requirements for Electrical

260519 Low-Voltage Electrical Power Conductors and Cables

260533 Raceways and Boxes for Electrical Systems

260543 Underground Ducts and Raceways for Electrical Systems

Division 31 Earthwork

310500 Geotextiles for Earthwork

311000 Site Clearing

312113 Radon Mitigation System

312219 Topsoil

312320 Street and Site Excavation, Grading, and Backfill

312500 Erosion and Sediment Control

Division 32 Exterior Improvements

321200 Asphalt Paving

321300 Exterior Concrete

321540 Washed Rock

321723 Pavement Markings

323113 Herbivory Protection Fence

328400 Landscape Irrigation

329223 Sodding

329300 Planting

Division 33 Utilities

334000 Storm Drain Systems

307127 YELL Rehabilitate Exteriors Historic Fort Yellowstone Buildings – Final Construction Documents

DIVISION 02: EXISTING CONDITIONS

022119 UTILITIES SURVEYS

None

024100 SITE DEMOLITION

024119 SELECTIVE DEMOLITION

307127 YELL Rehabilitate Exteriors Historic Fort Yellowstone Buildings – Final Construction Documents

DIVISION 03: CONCRETE

030100 MAINTENANCE OF CONCRETE

Cleaning Materials:

D/2 Biological Solution

Cementitious Patching and Repair Materials:

ARDEX Engineered Cements

Dayton Superior Corporation

Euclid Chemical Company – Eucopatch, Duraltop Flowable

W.R. Meadows, Inc.

Epoxy Patching and Repair Materials:

Euclid Chemical Company – Dural Injection Gel

Bonding Agent and Anti-Corrosion Coating:

Euclid Chemical Company – Duralprep A.C.

033000 CAST-IN-PLACE CONCRETE

Foundation Vent:

Air Vent, Inc. – FA109

Waterstops:

Sika Corporation Greenstreak - PVC Waterstops

034816 PRECAST ARCHITECTURAL CONCRETE

Precast Concrete Chimney Caps:

Custom

Precast Concrete Splash Blocks:

Custom

1/2

D/2 Biological Solutions, Inc. | PO Box 3746, Westport, MA 02790 | (917) 693-7441 | d2bio.com

D/2 Biological Solution

Discover the D/2 difference!

D/2 Biological Solution is a biodegradable, easy to use liquid that removes stains from mold, algae, mildew, lichens and air pollutants. It is effective on marble, granite, limestone, brownstone, travertine, masonry, terra cotta, concrete, stucco, wood, and other architectural surfaces including monuments, sculpture and headstones. A contact time of only 10 to 15 minutes followed by scrubbing with a soft nylon or natural bristle brush will loosen most biological and air pollutant staining.

D/2 Biological Solution is effective for removing harmful biological and air pollutant staining from many building materials including masonry, marble, granite, limestone, brownstone, travertine, terra cotta, concrete, stucco, wood, canvas and vinyl & aluminum siding.

Features and Benefits

• Fast acting: 10 to 15 minutes contact time for great results.

• Biodegradable

• Contains no acids, salts, or chlorine

• pH neutral

• Will not etch metals or glass

• Safer to use around plantings

• Is not a hazardous material and requires no special handling or protection

• Use full strength, no in-field mixing required

• Shelf life of 5 years

Application Procedures

Always do a spot test sample before proceeding with project. D/2 works best when air and surface temperatures are 45°F or above. Use

D/2 undiluted for best results. In the event of excessive plant exposure, rinse all plants and water in all planted ground areas.

Immediate Result Method

1. Apply D/2 Biological Solution with a brush, roller, hand pump sprayer (garden style pump sprayer) or low pressure power sprayer.

2. Allow undiluted D/2 to remain on the surface

10-15 minutes.

3. Apply additional D/2 as necessary to maintain a wet surface.

4. Scrub with soft nylon or natural bristle brush.

DO NOT USE METAL BRUSH.

5. Lightly mist with water and continue scrubbing.

6. Rinse thoroughly with clean, potable water.

No Scrub/No Rinse Method

1. Apply D/2 Biological Solution with a brush or pump sprayer to a dry surface. Do not pre-wet the surface.

2. Allow to dry. Repeat if there are heavy biological stains.

D/2 works with the elements and results occur within one week to one month depending on severity of growth and weather conditions. The surface will become cleaner over time as the subsurface biological stains release.

Safety Information

D/2 Biological Solution is non-mutagenic, and contains no carcinogenic compounds as defined by NTP, IARC, or OSHA. It is considered essentially non-toxic by swallowing, as it has an oral LD50 of 2.0 g/kg of body weight. No special ventilation is required during use.

2/2

D/2 Biological Solutions, Inc. | PO Box 3746, Westport, MA 02790 | (917) 693-7441 | d2bio.com

Packaging and Coverage

D/2 Biological Solution is available in 1 gallon and 5 gallon containers, and 55 gallon drums.

The area that can be treated with one gallon of

D/2 will vary considerably as a function of the nature and extent of biological deposits, as well as the physical characteristics of the surface.

Typical coverage to remove medium deposits will vary from 250 to 350 square feet per gallon.

Technical Data

Physical Form . . . . . Transparent, low viscosity liquid

Color . . . . . . . . . . . . . . . . . . . . . . . . Almost colorless pH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.5

Specific Gravity . . . . . . . . . . . . . . . . . . . . . . . 1.01g/cc

Solubility in Water . . . . . . . . . . . . . . . . . . . . Complete

Vapor Pressure . . . . . . . . . . . . . . 25 mm Hg @ 20°C

Notice: The information contained herein is based on our own research and the research of others, and it is provided solely as a service to help users. It is believed to be accurate to the best of our knowledge. However, no guarantee of its accuracy can be made, and it is not intended to serve as the basis for determining this product's suitability in any particular situation. For this reason, purchasers are responsible to make their own tests and assume all risks associated with using this product.

10/2012

ARDEX CPTM

Concrete Patch

AF 134 11/14

EN

G

IN

EE

R

ED

C O

N C

R

ET

E R

EP

AI

R S

Y

ST

EM

S

Trowel-grade, cementitious topping for filling and repairing concrete above, on or below grade.

Engineered with Portland cement and select high-performance polymers.

Install over: Interior and exterior concrete floors, walls, steps and ramps.

Key Features

• Freeze-thaw resistant

• Suitable for foot and rubber tire traffic

• Easy to apply and hardens quickly

• Horizontal and vertical application

Installation

• Packaging: 40 lb bag

• Coverage: 22.5 sq. ft. at 1/4” (21.1 m2 at 6 mm) per bag

• Neat: 1/4” to 1/2” (6 to 12 mm) neat

• Aggregate: up to 2” (5 cm)

• Working time: 30 minutes

• Pot life:30 minutes

• Walkable: 2 hours

• Apply:

• ARDEX CD™ in 4 hours

• ARDEX CG™ in 24 hours Performance

• ASTM C109 (air mod) Compressive Strength:

• 3,600 psi (253 kg/cm2) at 28 days

• VOC: 0

+1-724-203-5000 888-512-7339 www.ardexamericas.com

TECHNICAL DATA SHEET

Visit www.daytonsuperior.com for the most up to date technical information

C o n cr e te

R e p a ir

Sec

American Owned American Made

14-1

SECTION 14

Concrete Repair

PRODUCT PAGE

Guide To Concrete Repair ................................................................. 14-3

FORM & POUR REPAIR MORTARS

Civil / Structural FPX ........................................................................ 14-5 Perma Patch™ FP ............................................................................ 14-7

GENERAL USE REPAIR MORTARS

Polyfast™ FS ................................................................................... 14-9 Recrete™ 20 Minute ..................................................................... 14-11 Recrete™ 5 Minute ....................................................................... 14-13 Recrete™ Light 20 Minute ............................................................ 14-15

HORIZONTAL REPAIR MORTARS

HD 50 ............................................................................................. 14-17 Pave Patch 3000 ............................................................................. 14-19 Special Patch .................................................................................. 14-21 Thin Resurfacer .............................................................................. 14-23

RESINOUS REPAIR

Rapid Resin Repair ......................................................................... 14-25 Sure Patch™ .................................................................................. 14-27

SPECIALTY REPAIRS

Anchor All ...................................................................................... 14-29 Snaplugs® ..................................................................................... 14-31 Waterstop™ .................................................................................. 14-33

VERTICAL / OVERHEAD REPAIR

Architectural Finish™ .................................................................... 14-35 Civil / Structural VO ........................................................................ 14-37 HD 25 VO ....................................................................................... 14-39 Perma Patch™ VO ......................................................................... 14-41

C o n cr e te

R e p a ir

Sec

American Owned American Made

14-3

® Guide to Concrete Repair

In repair and restoration work it is recommended to first take care of the cause before repairing the effect. Many times a condition survey is needed to determine the cause(s) and to plan the proper, most cost-effective approach to correct the problem.

In repair and restoration surface preparation is very important.

The best of products with poor surface preparation is no better than the lesser product with the proper surface preparation.

Surface Preparation

■ I.K.E.

Identify what the problem is Know and understand the problem Eradicate the cause before addressing the effect

■ Surface Preparation: A necessity for a successful application:

Water-blast, sand-blast, scabbler, scarifier, grinder, needle gun, hammer chisels, shot-blasting

P rovide a high profile substrate for a good mechanical bond

Remove excessive or complex edge conditions

H ave a defined edge…saw cut or use a grinding wheel to create a clean defined edge to which you will work the repair mortar

■ SSD…concrete substrate to be in a Saturated-Surface-Dry condition so that the concrete will not absorb water from the repair mortar

■ Mixing methods: drill & paddle, mortar mixer, concrete mixer (when stone added), pump, by hand

■ When mixing less than a full bag always first mix the bag so that a representative sample is obtained.

■ Add the powder to the water

■ Water requirements stay the same regardless if the material is used neat or if pea gravel is used

■ Application methods: by hand, form & pump, form & pour, dry packing, pneumatic (spraying), pneumatic (shotcrete)

■ ICRI Guideline No. 03732 and the ACI 546 Concrete Repair

Guide provides an in depth description of various types of surface preps, substrate condition surveys, and selection & specifying methods of surface preparation

DayTON SupErIOr rEpaIr MOrTarS GEnEral UsE rEpaIrs:

reCrete™ 5 Minute & reCrete™ 20 Minute

■ Cost-effective repair mortar with no polymers or fibers

■ Min. thickness 1/8”, max. 2”, neat

■ Extend with clean washed stone > 2” per Data Sheet

■ Can be modified with Acrylic Bonding Agent J40 1:1, for enhanced performance polyfast™ Fs

■ Rapid setting vertical and overhead applications

■ Polymer modified

■ Min. thickness 1/4”, max. 2”, neat

■ Extend with clean washed stone > 2” per Data Sheet

■ Easily shaped and finished

■ Pleasing concrete gray color

VErtICal / OVErhEad:

architectural Finish™.

■ Polymer modified

■ Use for rubbing, smoothing, resurfacing repairing vertical surfaces

■ Colored blended to a light gray

■ 30 minute working time

■ Featheredge to 1/8” application depth perma patch VO™

■ One component W/water or 2-component W/approved admixture

■ High strength

■ Min. thickness 1/4”, max. 2” neat

■ Formulated for vertical / overhead applications

■ High bond strength

■ Shrinkage compensated

■ Can be sprayed or pumped through small volume pneumatic equipment

■ Rapid strength gain

■ Can be extended with aggregate for deep applications

■ Very low permeability hd-25 VO

■ Designed for vertical and overhead applications

■ Polymer modified

■ Min. thickness 1/4”, max. 2” neat

■ Extend with clean washed stone > 2” per Data Sheet

■ More rapid initial strength gain than Polyfast

9/17/12 • Page 1 of 1

TECHNICAL DATA SHEET

CONTINUED

C o n cre te R e p a ir

Sec

14-4 Visit www.daytonsuperior.com for the most up to date technical information

9/17/12 • Page 2 of 2

Civil / structural VO

■ Vertical or overhead applications

■ Formulated for use in spray applications using the wet process

■ Can also be applied be hand or trowel

■ Contains a corrosion inhibitor

■ Very high compressive strengths

FOrM & pOur:

Civil / structural FpX

■ For form & pour or horizontal applications

■ Extended with blended aggregate

■ Contains a corrosion inhibitor

■ Long working time perma patch™ F/p

■ Self finishing

■ Up to 40 minute working time

■ Ideal for form & pour or form & pump applications

HOrIzONTal:

thin resurfacer

■ Polymer modified

■ Min. thickness 1/16”, max. 1/2” and cannot be extended

■ Substitute 1 qt. Of water with J-40 for enhanced performance special patch

■ Shrinkage compensated

■ High early strength

■ Good resistance to freeze-thaw and impact hd-50

■ Pourable consistency

■ Very rapid setting

■ Polymer modified, fiber reinforced

■ Min. thickness ½”, max. 2”, neat

■ Extend with clean washed stone > 2” per Data Sheet

■ Capable of being extended up to 80% (40# stone) per bag

■ Most popular DOT approved repair mortar pave patch 3000

■ Pourable consistency

■ Shrinkage compensated

■ Very rapid setting

■ Min. thickness ½”, max. 2”, neat

■ Extend with clean washed stone > 2” per Data Sheet

■ Capable of being extended up to 60% (40# stone) per bag rESINOuS BaSED rEpaIr MOrTarS rapid resin repair

■ 100% solids 3-component low modulus repair material

■ Non-shrink

■ Chemically resistant

■ Cures from -20°F to 130°F

■ Meets USDA requirements

■ “0” VOC

■ Low odor sure patch™

■ 100% solids 3-component low modulus repair material

■ Trowelable

■ Rapid strength gain

■ Moisture insensitive

EpOxy/CEMENTITIOuS BONDINg agENT/rEBar prIMEr perma prime™ 3C

■ True breathable bonding agent

■ Long open time

■ Epoxy-modified with corrosion inhibitor

SpECIalTy rEpaIrS:

snaplugs®

■ High Strength cement compound

■ Plugs for tie cone holes

■ Gray in color

■ Saves time and labor anchor all

■ Shrinkage compensated

■ Pourable

■ Fast setting

■ Ideal for posts and dowels

Waterstop

■ Rapid setting hydraulic cement

■ For plugging & stopping water or fluid leaks in concrete or

CMU

■ Initial set 2½ min., final set 3½ min.

■ Non-corrosive, non-rusting

Guide to Concrete Repair

C o n cr e te

R e p a ir

Sec

American Owned American Made

14-5

DESCrIpTION One component, shrinkage compensated Portland-Cement based concrete repair material containing blended coarse aggregate.

Civil/Structural FPX is enhanced with a corrosion inhibitor for rebar & steel protection and is designed primarily for large volume placements including structural elements. typically in applications from 1 inch (2.54 cm) to 8 inches (20.32 cm).

uSE For repair of concrete utilizing form & pour or form & pump applications. Can be used on-grade, above, and below grade;

horizontal, vertical and overhead; interior or exterior; structural and general repairs where 1 in. (2.54 cm) to 8 in. (20.32 cm) thickness is required. Excellent for use as a repair material for parking facilities, industrial plants, bridges, tunnels, dams, balconies or any deep section repair of concrete.

FEaTurES

■ Pre-extended with coarse aggregate for labor saving.

■ Corrosion inhibitor protects steel reinforcement from both chloride intrusion and carbonation.

■ High bond strength.

■ Compatible with coefficient of thermal expansion of concrete.

■ Increased resistance to deicing salts.

■ Excellent for deep section structural repairs.

■ Freeze/Thaw resistant.

■ Extended working time for ease of placement.

■ Not a vapor barrier.

prOpErTIES Application Time: 45 min.-60 min.

Initial set: 1 hr. 30 min.

Consistency:

Initial: Flowable, Slump at 30 minutes: >4 in. (10.16 cm) Compressive Strength: ASTM C-39 1 day: 2,500 psi (17.2 MPa) 7 days: 4,500 psi (31.0 MPa) 28 days: 5,500 psi (37.9 MPa) Flexural Strength: ASTM C-78: 28 days 700 psi (4.83 MPa) Splitting Tensile Strength: ASTM C-496: 28 days 750 psi (5.17 MPa) Bond Strength: ASTM C-882, modified: 28 days 1,500 psi (10.3 MPa) note: The data shown is typical for controlled laboratory conditions. Reasonable variation from these results can be expected due to interlaboratory precision and bias. When testing the field mixed material, other factors such as variations in mixing, water content, temperature and curing conditions should be considered.

ESTIMaTINg guIDE Yield: Approximately 0.44 cu. ft. (0.0125 cu m) /55 lb. (24.9 kg) bag paCKagINg

ItEM # paCKaGE sIZE lbs. kg

308765 Bag 55 24.94

308771 Supersak 2500 1133.98

STOragE Civil/Structural FPX should be stored in a cool, dry interior area.

At no time, should material be exposed to high moisture, rain or snow conditions. Shelf life of unopened bags, when stored in a dry facility is 12 months.

applICaTION surface preparation: The concrete must be sound and free of all foreign material, including oil, grease, dust, laitance, or other surface contaminants. Surface preparation in accord with ICRI Guidelines is recommended. Saw cut the perimeter of the repair to a maximum depth of ½ in. (1.3 cm). Best results will be obtained by abrasive blasting the area to be repaired, providing uniform depth, a high surface profile and a firm bonding area.

All surfaces to be repaired should be in a saturated-surface-dry (SSD) condition with no standing water on the surface.

Supported patches deeper than 2 in. (5.08 cm) may require reinforcement or anchorage. Applications for unsupported repairs exceeding 1in. (2.54 cm) in thickness may require anchorage. Please consult the engineer of record for special requirements that may be required.

Mixing: Never mix partial bags. Mix with a forced action mixer.

Use suitable size container with an appropriate paddle at a slow speed (400-500 rpm) with a heavy duty drill. For larger projects use a mortar mixer. Add recommended amount of water into the container followed by the Civil/Structural FPX powder. Mix thoroughly for at least 5 minutes.

Water requirements: Add 4.5 pints (2.1 L) of clean potable water /55 lb. (24.9 kg) bag.

placement: Using freshly mixed Civil/Structural FPX (do not dilute), scrub a thin layer into the SSD substrate with a stiff

Civil/Structural FPX Form & Pour Extended Repair Mortar

10/11/11 • Page 1 of 2

TECHNICAL DATA SHEET

CONTINUED

C o n cre te R e p a ir

Sec

14-6 Visit www.daytonsuperior.com for the most up to date technical information

10/11/11 • Page 2 of 2 brush and place the Civil/Structural FPX before the scrub coat dries. In certain conditions the use of an approved Dayton Superior surface bonding agent, may be required. Contact Technical services for further information. Mix only enough material that can be placed within a 40-minute period. DO NO

RETEMPER.

Apply Civil/Structural FPX by pour or pump into a formed vertical surface or horizontal area . Confirm pump type and hose diameters will accept material with pump manufacturer prior to placement. Place at a minimum depth of 1 in. (2.54 cm) up to 8

in. (20.32 cm). DO NOT FEATHER EDGE.

Curing: Formwork should remain in place until material reaches 2500 psi (17.2 MPa) or as specified by engineering documents.

To assure maximum durability, moist cure or use approved Dayton Superior curing compound conforming to ASTM C309.

ClEaN up Clean tools and equipment while material is still wet with water.

Hardened material requires mechanical or abrasive methods.

lIMITaTIONS FOr prOFESSIONal uSE ONly Application thickness: Minimum 1 in. (2.54 cm) Maximum 8 in.

(20.32 cm).

Do not place at temperatures below 40°F(5°C) or if the temperature is expected to drop below 40°F(5°C) in the next 24 hours.

In hot weather follow ACI Committee 305 recommended procedures.

Colder temperatures will extend the setting time and warmer temperatures will reduce the setting time.

Please consult the engineer of record for the project for special requirements.

prECauTIONS rEaD MSDS prIOr TO uSINg prODuCT

■ Product contains Crystalline Silica and Portland Cement, Avoid breathing dust – Silica may cause serious lung problems

■ Use with adequate ventilation

■ Wear protective clothing, gloves and eye protection (Goggles, Safety Glasses and/or Face Shield)

■ Keep out of the reach of children

■ Do not take internally

■ In case of ingestion, seek medical help immediately

■ May cause skin irritation upon contact, especially prolonged or repeated. If skin contact occurs, wash immediately with soap and water and seek medical help as needed

■ If eye contact occurs, flush immediately with clean water and seek medical help as needed

■ Dispose of waste material in accordance with federal, state and local requirements

MaNuFaCTurEr Dayton Superior Corporation 1125 Byers Road Miamisburg, OH 45342 Customer Service: 888-977-9600 Technical Services: 866-329-8724 Website: www.daytonsuperior.com

WarraNTy Dayton Superior Corporation (“Dayton”) warrants for 12 months from the date of manufacture or for the duration of the published product shelf life, whichever is less, that at the time of shipment by Dayton, the product is free of manufacturing defects and conforms to Dayton’s product properties in force on the date of acceptance by Dayton of the order. Dayton shall only be liable under this warranty if the product has been applied, used, and stored in accordance with Dayton’s instructions, especially surface preparation and installation, in force on the date of acceptance by Dayton of the order. The purchaser must examine the product when received and promptly notify Dayton in writing of any non-conformity before the product is used and no later than 30 days after such non-conformity is first discovered. If Dayton, in its sole discretion, determines that the product breached the above warranty, it will, in its sole discretion, replace the non-conforming product, refund the purchase price or issue a credit in the amount of the purchase price. This is the sole and exclusive remedy for breach of this warranty. Only a Dayton officer is authorized to modify this warranty. The information in this data sheet supersedes all other sales information received by the customer during the sales process. THE FOREGOING WARRANTY SHALL BE EXCLUSIVE AND IN

LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES

OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND ALL OTHER

WARRANTIES OTHERWISE ARISING BY OPERATION OF LAW, COURSE OF DEALING,

CUSTOM, TRADE OR OTHERWISE.

Dayton shall not be liable in contract or in tort (including, without limitation, negligence, strict liability or otherwise) for loss of sales, revenues or profits; cost of capital or funds; business interruption or cost of downtime, loss of use, damage to or loss of use of other property (real or personal); failure to realize expected savings;

frustration of economic or business expectations; claims by third parties (other than for bodily injury), or economic losses of any kind; or for any special, incidental, indirect, consequential, punitive or exemplary damages arising in any way out of the performance of, or failure to perform, its obligations under any contract for sale of product, even if Dayton could foresee or has been advised of the possibility of such damages. The Parties expressly agree that these limitations on damages are allocations of risk constituting, in part, the consideration for this contract, and also that such limitations shall survive the determination of any court of competent jurisdiction that any remedy provided in these terms or available at law fails of its essential purpose.

Civil/Structural FPX Form & Pour Extended Repair Mortar

C o n cr e te

R e p a ir

Sec

American Owned American Made

14-7

DESCrIpTION Perma Patch™ FP is a specially designed patching and structural repair product for any maintenance and new construction projects where prolonged working time up to 40 minutes and fast strength in two to three hours is required.

uSE Can be used for all structural and general horizontal concrete repairs (interior, exterior, above and below grade) where sufficient working time during placement and high early strength is required.

FEaTurES

■ Flowable/self consolidating

■ Up to 40 minutes working time

■ Ideal for horizontal or formed vertical/overhead applications prOpErTIES Initial Setting Time (ASTM C-266) 30-40 min.

Final Setting Time (ASTM C-266) 45-55 min.

Compressive Strength ASTM C-109 3 hours >1000 psi (6.89 MPa) 1 day >2500 psi (17.24 MPa) 7 days >6000 psi (41.37 MPa) 28 days >8500 psi (58.62 MPa) Flexural Stength ASTM C-78 7 days 1000psi 28 days 1100 psi Splitting Tensile ASTM C496 1 day 200 psi 7 days 525 psi 28 days 675 psi Direct Tensile CRD C 164 1 day 125 psi 7 days 150 psi 28 days 190 psi Modulus of Elasticity ASTM C469 28 days 4.5 x 10-6 psi Bond Strength ACI 503R 1 day 150 psi 7 days 175 psi 28 days 250 psi Coefficient of thermal expansion CRD C39 modified

4.9 x 10-6 o in/in/degF Freeze/thaw resistance ASTM C666 procedure A 300 cycles >95% Scaling resistance ASTM C672 50 cycles 0 rating

Rapid chloride permeability ASTM C1202 28 days 770 coulombs

TEST DATA at 75° F (23.9°C)

Note: The data shown is typical for controlled laboratory conditions. Reasonable variation from these results can be expected due to interlaboratory precision and bias. When testing the field mixed material, other factors such as variations in mixing, water content, temperature and curing conditions should be considered.

ESTIMaTINg guIDE Yield: 0.38 cu. ft. /50 lb. (0.0107 cu m /22.7 kg) bag paCKagINg

ItEM # paCKaGE sIZE lbs. kg

308246 Bag 50 22.67

STOragE Shelf life of unopened bags, when stored in a dry facility, is 12 months. Excessive temperature differential and/or high humidity can shorten the shelf life expectancy. Store in a cool, dry area free of direct sunlight.

applICaTION surface preparation: The concrete must be sound and free of all foreign material, including oil, grease, dust, laitance, or other surface contaminants. Surface preparation in accord with ICRI Guidelines is recommended. Saw cut the perimeter of the repair to a maximum depth of ½ in. (1.3 cm). Best results will be obtained by abrasive blasting the area to be repaired, providing uniform depth, a high surface profile and a firm bonding area.

All surfaces to be repaired should be in a saturated-surface-dry (SSD) condition with no standing water on the surface.

Supported repairs deeper than 2 in. (5.1 cm) may require reinforcement or anchorage. Please consult the engineer of record for the project for special requirements.

Mixing: Mix with a low speed drill or, for larger projects, a mortar mixer. Add recommended amount of mixing liquid into the container followed by Perma Patch™ FP powder. Do not mix more than 3 minutes. Mix only enough material that can be placed within 40-minute period. Do No Retemper.

Water requirements standard Mix: Add 7 pints (3.29 L) of clean potable water /50

lb. (22.7 kg) bag.

acrylic admix: Add 7 pints (3.29 L) of Acrylic Bonding Agent J40 diluted 1:1 with clean potable water per 50 lb. (22.7kg) bag.

Perma Patch™ FP Form & Pour Repair Mortar

TECHNICAL DATA SHEET

CONTINUED

C o n cre te R e p a ir

Sec

14-8 Visit www.daytonsuperior.com for the most up to date technical information

10/11/11 • Page 2 of 2

For improved performance and greater adhesion, use Dayton Superior Acrylic Bonding Agent J-40 for part of the mix water.

plaCEMEnt:

Vertical: Apply Perma Patch™ FP by pour or pump into a formed vertical surface. Care should be taken to confirm pump and hose diameters would accept material with pump manufacturer Material can be placed neat to a minimum of ¼

in. (0.6 cm) up to a maximum thickness of 2 in. (5.1 cm) depth.

Pour or pump material into formed areas.

horizontal: Using freshly mixed Perma Patch™ FP (do not dilute), scrub a thin layer into the SSD substrate with a stiff brush and place the Perma Patch™ FP before the scrub coat dries. Material can be placed neat to a minimum of ¼ in. (0.6

cm) up to a maximum depth of 2 in. (5.1 cm). Pour or pump material into curbed areas. DO NOT FEATHER EDGE.

Extending for Volume placement: For patches over 2 in. (5.1

cm) in depth add 30-60% by weight 15-30 lbs. (6.8-13.6 kg) clean, SSD, 3/8 in.(0.1 cm) pea gravel. Extension will depend on depth and finish desired. Placement of 6-50 lbs. (22.67 kg) bags is the maximum amount for any one application. For larger applications, contact Technical Services.

CurINg Perma Patch™ FP is self-curing under most conditions, however, to assure maximum durability under severe drying conditions (wind, high temperature, low humidity), water cure or use approved ASTM C-309 Dayton Superior water based curing compound.

ClEaN up Use water when material is wet. Hardened material requires abrasive methods.

lIMITaTIONS FOr prOFESSIONal uSE ONly When using less than one bag always dry mix the full bag prior to each use.

Do not place at temperatures below 40°F(5°C) or if the temperature is expected to drop below 40°F(5°C) in the next 24 hours.

In hot weather follow ACI Committee 305 recommended procedures.

Colder temperatures will extend the setting time and warmer temperatures will reduce the setting time.

Not for use as a parge coating or stucco type application.

Placement of 6-50 lb. (22.7 kg) bags is the maximum amount for any one application.

Mixing equipment should be cleaned with water frequently and prior to material hardening.

prECauTIONS rEaD MSDS prIOr TO uSINg prODuCT

■ Product contains Crystalline Silica and Portland Cement, Avoid breathing dust – Silica may cause serious lung problems

■ Use with adequate ventilation

■ Wear protective clothing, gloves and eye protection (Goggles, Safety Glasses and/or Face Shield)

■ Keep out of the reach of children

■ Do not take internally

■ In case of ingestion, seek medical help immediately

■ May cause skin irritation upon contact, especially prolonged or repeated. If skin contact occurs, wash immediately with soap and water and seek medical help as needed

■ If eye contact occurs, flush immediately with clean water and seek medical help as needed

■ Dispose of waste material in accordance with federal, state and local requirements

MaNuFaCTurEr Dayton Superior Corporation 1125 Byers Road Miamisburg, OH 45342 Customer Service: 888-977-9600 Technical Services: 866-329-8724 Website: www.daytonsuperior.com

WarraNTy Dayton Superior Corporation (“Dayton”) warrants for 12 months from the date of manufacture or for the duration of the published product shelf life, whichever is less, that at the time of shipment by Dayton, the product is free of manufacturing defects and conforms to Dayton’s product properties in force on the date of acceptance by Dayton of the order. Dayton shall only be liable under this warranty if the product has been applied, used, and stored in accordance with Dayton’s instructions, especially surface preparation and installation, in force on the date of acceptance by Dayton of the order. The purchaser must examine the product when received and promptly notify Dayton in writing of any non-conformity before the product is used and no later than 30 days after such non-conformity is first discovered. If Dayton, in its sole discretion, determines that the product breached the above warranty, it will, in its sole discretion, replace the non-conforming product, refund the purchase price or issue a credit in the amount of the purchase price. This is the sole and exclusive remedy for breach of this warranty. Only a Dayton officer is authorized to modify this warranty. The information in this data sheet supersedes all other sales information received by the customer during the sales process. THE FOREGOING WARRANTY SHALL BE EXCLUSIVE AND IN

LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES

OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND ALL OTHER

WARRANTIES OTHERWISE ARISING BY OPERATION OF LAW, COURSE OF DEALING,

CUSTOM, TRADE OR OTHERWISE.

Dayton shall not be liable in contract or in tort (including, without limitation, negligence, strict liability or otherwise) for loss of sales, revenues or profits; cost of capital or funds; business interruption or cost of downtime, loss of use, damage to or loss of use of other property (real or personal); failure to realize expected savings;

frustration of economic or business expectations; claims by third parties (other than for bodily injury), or economic losses of any kind; or for any special, incidental, indirect, consequential, punitive or exemplary damages arising in any way out of the performance of, or failure to perform, its obligations under any contract for sale of product, even if Dayton could foresee or has been advised of the possibility of such damages. The Parties expressly agree that these limitations on damages are allocations of risk constituting, in part, the consideration for this contract, and also that such limitations shall survive the determination of any court of competent jurisdiction that any remedy provided in these terms or available at law fails of its essential purpose.

Perma Patch™ FP Form & Pour Repair Mortar

C o n cr e te

R e p a ir

Sec

American Owned American Made

14-9

DESCrIpTION Polyfast™ FS is a is shrinkage compensated, high strength mortar containing portland cement, special polymers and additives to provide an outstanding strength gain along with a fast set. Polyfast™ FS is a single component trowelable material formulated for vertical, overhead and horizontal repairs.

uSE Polyfast™ FS is a polymer modified mortar that can be used for vertical, horizontal and overhead repairs of concrete structures for interior or exterior, above or below grade applications. It can be used as a structural repair for bridges, tunnels, parking structures, dams, walls, columns, etc. It is also excellent for the repair of precast concrete products, i.e., pipes, beams, steps, etc.

FEaTurES

■ Ideal for vertical and overhead applications

■ Higher strength than typical concrete

■ “Built-in” bonding agent/polymer modified

■ Very low chloride permeability

■ Fast setting

■ One component – just add water

■ Excellent bond strength

■ Shrinkage compensating prOpErTIES Set Times: ASTM C-266 @ 72°F (22°C) Initial Set: 30 minutes Final Set: 45 minutes

Compressive Strength: ASTM C-109 1 Day 4,100 psi (22.2 MPa) 3 Days 6,500 psi (44.8 MPa) 7 Days 8,100 psi (55.8 MPa) 28 Days 9,000 psi (62.0 MPa)

Bond Strength: ASTM C-1042 7 Days 5,100 psi (35.1 MPa)

Flexural Strength: ASTM C-348 7 Days 1,100psi (7.6 MPa) 28 Days 2,000psi (13.8 MPa)

Length Change of Hardened Cement Mortar and Concrete:

ASTM C-157 and ASTM C-928:

Water Cure Air Cure 28 Days 0.027% -0.030% ASTM C-928 Max to 0.15% Max to -0.15% note: The data shown is typical for controlled laboratory conditions. Reasonable variation from these results can be expected due to interlaboratory precision and bias. When testing the field mixed material, other factors such as variations in mixing, water content, temperature and curing conditions should be considered.

ESTIMaTINg guIDE Approximately 0 .42 cu. ft. /50 lb.(0.012 cu m /22.67 kg) bag or pail.

paCKagINg

ItEM # paCKaGE sIZE lbs. kg

67358 Bag 50 22.67

67359 Pail 50 22.67

STOragE Shelf life of unopened bags, when stored in a dry facility, is 12 months. Excessive temperature differential and/or high humidity can shorten the shelf life expectancy. Store in a cool, dry area free of direct sunlight.

applICaTION surface preparation: The concrete must be sound and free of all foreign material, including oil, grease, dust, laitance, or other surface contaminants. Surface preparation in accord with ICRI Guidelines is recommended. Saw cut the perimeter of the repair to a maximum depth of ½ in (1.3 cm). Best results will be obtained by abrasive blasting the area to be repaired, providing uniform depth, a high surface profile and a firm bonding area.

All surfaces to be repaired should be in a saturated-surface-dry (SSD) condition with no standing water on the surface.

Supported patches deeper than 2 in. (5.1 cm) may require reinforcement or anchorage. Consult project engineer for specific requirements.

Mixing: Mix only as much product that can be easily placed within 10 minutes. Polyfast™ FS sets initially in approx. 30 minutes. For mixing, Dayton Superior recommends a low RPM drill with a mud paddle. When mixing less than a full unit, always first agitate the bag/pail so that a representative sample is obtained. Always add Polyfast™ FS to the water, thoroughly mixing to a putty-like consistency for at least 2-3 minutes.

Water requirements: 3.5 to 4 quarts. (3.3 - 3.8L)/50 lb. (22.7

kg) bag or pail. Use less water for a stiffer mix.

Polyfast™ FS Repair Mortar

6/26/12 • Page 1 of 2

TECHNICAL DATA SHEET

CONTINUED

C o n cre te R e p a ir

Sec

14-10 Visit www.daytonsuperior.com for the most up to date technical information

6/26/12 • Page 2 of 2 placement: Using freshly mixed material, scrub a thin layer into the SSD substrate with a stiff fiber brush and place the repair mortar by trowel or hand before the scrub coat dries. Trowel the material onto the surface to a minimum thickness of ¼ in. (0.6

cm) and a maximum neat thickness of 2 in. (5.1 cm). Additional lifts can be placed up to 6 in. (15.2 cm) and between each lift, the substrate must be left roughened or scarified. Prior to each lift, the surface must be in a SSD condition and a scrub coat applied immediately prior to the next lift being applied.

The less Polyfast™ FS is handled the better. Application should always be finished by the time of initial set or stiffening. Never leave excess material lapping over the edges of the repair. The finished repair should be smooth and level with the surrounding concrete. After leveling, Polyfast™ FS can be finished to achieve desired texture with broom, sponge, float or trowel.

For repairs over 2 in. (5.1 cm) thick, rather than applying in lifts, up to 15 lbs. (6.8 kg) of clean, SSD pea gravel /50 lbs. (22.7 kg.)

can be added to the Polyfast™ FS.

CurINg Adequate curing is important, especially during windy, hot or dry conditions. A wet burlap cure or a Dayton Superior water based curing compound,.

ClEaN up Use water when material is wet. Hardened material requires abrasive methods.

lIMITaTIONS FOr prOFESSIONal uSE ONly When using less than one bag always dry mix the full bag prior to each use.

DO NOT place at unprotected temperatures below 40°F(5°C) or if the temperature is expected to drop below 40°F(5°C) in the next twenty-four hour period.

Ideal installation temperatures are from 50°F (10°C) to 80°F (27°C).

Cooler temperatures will slow set-time and strength gain.

Hot temperatures will accelerate set time. In hot weather, follow ACI Committee 305 recommended procedures.

Do not apply over a smooth hard toweled surfaces without first roughening the surface.

DO not featheredge. Minimum thickness for patching is ¼ in.

(0.6 cm).

Do not re-temper the mixed material or use admixtures.

Mixing equipment should be cleaned with water frequently and prior to material hardening.

Not for use as a parge coating or stucco type application.

prECauTIONS rEaD MSDS prIOr TO uSINg prODuCT

■ Product contains Crystalline Silica and Portland Cement, Avoid breathing dust – Silica may cause serious lung problems

■ Use with adequate ventilation

■ Wear protective clothing, gloves and eye protection (Goggles, Safety Glasses and/or Face Shield)

■ Keep out of the reach of children

■ Do not take internally

■ In case of ingestion, seek medical help immediately

■ May cause skin irritation upon contact, especially prolonged or repeated. If skin contact occurs, wash immediately with soap and water and seek medical help as needed

■ If eye contact occurs, flush immediately with clean water and seek medical help as needed

■ Dispose of waste material in accordance with federal, state and local requirements

MaNuFaCTurEr Dayton Superior Corporation 1125 Byers Road Miamisburg, OH 45342 Customer Service: 888-977-9600 Technical Services: 866-329-8724 Website: www.daytonsuperior.com

WarraNTy Dayton Superior Corporation (“Dayton”) warrants for 12 months from the date of manufacture or for the duration of the published product shelf life, whichever is less, that at the time of shipment by Dayton, the product is free of manufacturing defects and conforms to Dayton’s product properties in force on the date of acceptance by Dayton of the order. Dayton shall only be liable under this warranty if the product has been applied, used, and stored in accordance with Dayton’s instructions, especially surface preparation and installation, in force on the date of acceptance by Dayton of the order. The purchaser must examine the product when received and promptly notify Dayton in writing of any non-conformity before the product is used and no later than 30 days after such non-conformity is first discovered. If Dayton, in its sole discretion, determines that the product breached the above warranty, it will, in its sole discretion, replace the non-conforming product, refund the purchase price or issue a credit in the amount of the purchase price. This is the sole and exclusive remedy for breach of this warranty. Only a Dayton officer is authorized to modify this warranty. The information in this data sheet supersedes all other sales information received by the customer during the sales process. THE FOREGOING WARRANTY SHALL BE EXCLUSIVE AND IN

LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES

OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND ALL OTHER

WARRANTIES OTHERWISE ARISING BY OPERATION OF LAW, COURSE OF DEALING,

CUSTOM, TRADE OR OTHERWISE.

Dayton shall not be liable in contract or in tort (including, without limitation, negligence, strict liability or otherwise) for loss of sales, revenues or profits; cost of capital or funds; business interruption or cost of downtime, loss of use, damage to or loss of use of other property (real or personal); failure to realize expected savings;

frustration of economic or business expectations; claims by third parties (other than for bodily injury), or economic losses of any kind; or for any special, incidental, indirect, consequential, punitive or exemplary damages arising in any way out of the performance of, or failure to perform, its obligations under any contract for sale of product, even if Dayton could foresee or has been advised of the possibility of such damages. The Parties expressly agree that these limitations on damages are allocations of risk constituting, in part, the consideration for this contract, and also that such limitations shall survive the determination of any court of competent jurisdiction that any remedy provided in these terms or available at law fails of its essential purpose.

Polyfast™ FS

C o n cr e te

R e p a ir

Sec

American Owned American Made

14-11

DESCrIpTION Recrete™ 20 Minute is a general purpose cement based concrete repair and patching material. Recrete™ 20 Minute is specially formulated to provide a fast setting repair mortar with excellent workability. Recrete™ 20 Minute can be used for repair and patching of vertical, overhead and horizontal areas subject to light traffic both interior and exterior.

uSE Recrete™ 20 Minute is a general purpose concrete patching product which can be used to repair concrete pipe, precast concrete products, large floor cracks, concrete steps, walls, columns, concrete blocks, sidewalks, driveways, etc. The Recrete™ 20 Minute is ideal for vertical and overhead applications because of its “putty-like” consistency and it’s ability to be shaped, molded and sanded.

FEaTurES

■ Suitable for horizontal, vertical and overhead applications

■ Twice the strength of typical concrete

■ Can be shaped and molded

■ Fast setting

■ Rapid strength gain, over 3000 psi (20.7 MPa) in 24 hours prOpErTIES Compressive strength test and setting times have been determined and established in accordance with ASTM C-109 and

ASTM C-266.

Compressive Strength - ASTM C-109 1 day 3,000 psi (20.7 MPa) 7 days 4,500 psi (31.0 MPa) 28 days 6,500 psi (44.8 MPa)

Set Time- ASTM C-266 Initial: 15 minutes Final: 35 minutes note: The data shown is typical for controlled laboratory conditions. Reasonable variation from these results can be expected due to interlaboratory precision and bias. When testing the field mixed material, other factors such as variations in mixing, water content, temperature and curing conditions should be considered.

ESTIMaTINg guIDE Yield: 0 .45 to 0.48 cu. ft. /50 lb. (0.0126 - 0.0134 cu m /22.7 kg) bag or pail.

paCKagINg

ItEM # paCKaGE sIZE lbs. kg

67311 Bag 50 22.67

67312 Pail 50 22.67

STOragE Shelf life of unopened containers, when stored in a dry facility, is 12 months. Excessive temperature differential and /or high humidity can shorten the shelf life expectancy. Store in a cool, dry area free of direct sunlight.

applICaTION surface preparation: Remove all dirt, grease, oil and surface coatings that will come in contact with the repair material. All loose concrete must be removed until firm substrate is exposed.

On horizontal patches, best results will be obtained by saw cutting the area to be repaired up to a maximum of ½ in. (1.3

cm) providing uniform depth with a high surface profile. The actual depth of repair can be greater than the ½ in. (1.3 cm) saw cut. All surfaces to be repaired should be in a saturated surface dry (SSD) condition with no standing water on the surface. Using freshly mixed Recrete™ 20 Minute, scrub a thin layer onto the SSD substrate with a stiff fiber brush and place the Recrete™ 20 Minute before this bond coat dries.

Mixing: Mix only as much as can be easily placed within 10 minutes. Recrete™ 20 Minute sets initially in approximately 15 minutes depending upon temperature. Always add Recrete™ 20 Minute to the water, thoroughly mixing to a putty like consistency for at least 2 – 3 minutes. For mixing, Dayton Superior recommends a low RPM drill with a mud paddle. When mixing less than a full unit, always first agitate the bag/pail so that a representative sample is obtained.

Water requirements: Mix with water at the rate of 4 – 5 quarts /50 lb. (3.8 – 4.8 L /22.67 kg) bag. For improved performance and greater adhesion, use Dayton Superior Acrylic Bonding Agent J40 for part of the mix water. Dilute the Acrylic Bonding Agent J40 with up to 3 parts water and use the diluted mixture for mixing of the Recrete™ 20 Minute.

Acrylic Bonding Agent J40 is recommended as an admixture for the Recrete™ 20 Minute for all applications subject to frequent freezing and thawing cycles or for projects where enhanced physical properties are desired.

placement: Following proper bond coat application, pack the material firmly into the prepared area, ensuring intimate contact with the bonding surface. Use slightly more material than is

Recrete™ 20 Minute

08/23/12 • Page 1 of 2

TECHNICAL DATA SHEET

CONTINUED

C o n cre te R e p a ir

Sec

14-12 Visit www.daytonsuperior.com for the most up to date technical information

08/23/12 • Page 2 of 2 needed and roughly shape during placement. After the initial set, when Recrete™ 20 Minute is surface hard, shave the material to the desired final shape using a steel trowel. Maximum depth of neat repair mortar is 2 in. (5.1 cm) for each lift. For large repairs over 2 in. (5.1 cm) thick, up to 25 lbs. (11.34 kg) of clean, SSD pea gravel should be added per 50 lbs. (22.67 kg.) of Recrete™ 20 Minute.

THE LESS RE-CRETE 20 MINUTE SET IS HANDLED THE BETTER.

DO NOT ADD EXCESS WATER OR RETEMPER.

Never leave excess material lapping over edges of repair.

Finished patch should be smooth and level with the surrounding concrete. After leveling, Recrete™ 20 Minute can be rubbed with a wet sponge and textured, if desired.

Curing: Adequate curing is important, especially during windy, hot and dry conditions. A wet burlap cure or a Dayton Superior water based curing compound or cure & seal is recommended.

ClEaN up Use water prior to material setting hard. Hardened material requires abrasive removal methods.

lIMITaTIONS FOr prOFESSIONal uSE ONly Minimum thickness for repair is 1/8 in (0.3 cm). Do not feather edge.

Do not use for resurfacing or topping large floor areas.

Not for use as a parge coating or stucco type application.

Do not add other cements or additives to this product.

Mixing equipment should be cleaned with water frequently and prior to material hardening.

Cold weather will slow down the set time of Recrete™ 20 Minute and hot weather will accelerate it. The minimum application temperature is 40°F (4°C).

Prepackaged material segregates while in the bag, thus when mixing less than a full bag it is recommended to first agitate the bag to assure it is blended prior to sampling.

prECauTIONS rEaD…