B.08 Appendix C - Up River Vertical Turbine Pump O_M Manual.pdf

ITT Corporation Industrial Process Goulds Pumps Engineered Systems-Los Angeles 3951 Capitol Avenue City of Industry, CA 90601

(P) 562-908-4181

EQUIPMENT

INSTALLATION, OPERATION AND MAINTENANCE

PACKAGE

UP RIVER PUMP STATION

PROJECT NAME: SAVANNAH HARBOR EXPANSION PROJECT (SHEP) DISSOLVED OXYGEN INJECTION SYSTEM

SOLICITITION NUMBER: W912HN-13-R-0018

OWNER: U.S. ARMY CORPS OF ENGINEERS (SAVANNAH DISTRICT)

100 WEST OGLETHORPE AVENUE

SAVANNAH, GA 31401

SITE ADDRESS: SHEP DISSOLVED OXYGEN INJECTION SYSTEM-UP RIVER

PLANT MCINTOSH ROAD

RINCON, GA 31326

GENERAL CONTRACTOR: CDM CONSTRUCTORS, INC.

2301 MAITLAND CENTER PARKWAY

SUITE 300

MAITLAND, FL 32751

(P) 407-660-2552

(F) 407-660-8912

MANUFACTURER: ITT GOULDS- ENGINEERED SYSTEMS-LOS ANGELES (ESLA)

LOCAL REPRESENTATIVE: TENCARVA MACHINERY COMPANY

1370 UNION HILL INDUSTRIAL COURT

SUITE G

ALPHARETTA, GA 30004

(P) 770-643-4859

(F) 770-552-0319

EQUIPMENT: VERTICAL TURBINE PUMP ASSEMBLIES

SPECIFICATION SECTION: 43 21 39 – PUMPS: WATER, VERTICAL TURBINE

SUBMITTAL DATE: DECEMBER 20, 2017

Table of Contents

1. Equipment Scope of Supply Speece Cone Pumps UP-1/UP-2/UP-3 Equipment Scope of Supply High Pressure Screen Backwash Pumps UP-4/UP-7 Equipment Scope of Supply Mixing Water Pumps UP-5/UP-8 Equipment Scope of Supply Low Pressure Screen Backwash Pumps UP-6/UP-9 Equipment Scope of Supply Up River Vertical Turbine Pump Grease Lubrication System Equipment Scope of Supply

2. Sample Nameplates Vertical Turbine Pump Nameplate Sample Vertical High Thrust Motor Sample Nameplate

3. Vertical Turbine Pump Curves Speece Cone Pumps UP-1/UP-2/UP-3 High Pressure Screen Backwash Pumps UP-4/UP-7 Mixing Water Pumps UP-5/UP-8

Low Pressure Screen Backwash Pumps UP-6/UP-9

4. Vertical Turbine Pump Data Speece Cone Pumps UP-1/UP-2/UP-3 High Pressure Screen Backwash Pumps UP-4/UP-7 Mixing Water Pumps UP-5/UP-8 Low Pressure Screen Backwash Pumps UP-6/UP-9

5. Vertical Turbine Pump Coating Data and Coating Procedure Intershield 300V Abrasion Resistant Auminum Pure Epoxy Data Sheet Intersleek 381 Silicone Elastomer Tie Coat Data Sheet Intersleek 425 Silicone Elastomer Foul Release Data Sheet Blasting and Coating Procedure 12708-AF AkzoNobel Intersleek 425 Suitability Letter

6. Vertical Turbine Pump Assembly Dimensional Data Speece Cone Pumps UP-1/UP-2/UP-3 General Arrangement Drawings High Pressure Screen Backwash Pumps UP-4/UP-7 General Arrangement Drawings Mixing Water Pumps UP-5/UP-8 General Arrangement Drawings Low Pressure Screen Backwash Pumps UP-6/UP-9 General Arrangement Drawings

7. Vertical Turbine Pump Installation, Operation and Maintenance Manual

8. Vertical Turbine Pump Motor Data Nidec General Information for Integral Horsepower Motors on Variable Frequency Drives Speece Cone Pumps UP-1/UP-2/UP-3 High Pressure Screen Backwash Pumps UP-4/UP-7 Mixing Water Pumps UP-5/UP-8 Low Pressure Screen Backwash Pumps UP-6/UP-9

9. Vertical Turbine Pump Motor Installation, Operation and Maintenance Manual

10. Recommended Pump Spare Parts & Anticipated Service Life

11. Vertical Turbine Pump Zinc Anode Data

12. Recommended Pump and Motor Lubricants

13. Vertical Turbine Pump Operating Speeds

14. Vertical Turbine Pump Grease Lubrication System Data Safety Precautions Hydraulic Troubleshooting Electric Motor Troubleshooting UPS-1 & UPS-2 Mechanical Components Drawing UPS-1 & UPS-2 Dimensional Drawing UPS-1 & UPS-2 P&ID Drawing UPS-1 Schematic Drawings UPS-2 Schematic Drawings UPS-1 & UPS-2 Mechanical Component Data UPS-1 & UPS-2 Electrical Component Data Grease System Accessory Data UP-1/2/3 Distribution Panel Dimensional Drawing UP-4/UP-7 Distribution Panel Dimensional Drawing UP-5/6/8/9 Distribution Panel Dimensional Drawing UP-1/2/3 P&ID Drawing UP-4/7 P&ID Drawing UP-5/6/8/9 P&ID Drawing Distribution Panel Mechanical Component Data UP-1 Distribution Schematic Drawings UP-2 Distribution Schematic Drawings UP-3 Distribution Schematic Drawings UP-4 Distribution Schematic Drawings UP-5 Distribution Schematic Drawings UP-6 Distribution Schematic Drawings UP-7 Distribution Schematic Drawings UP-8 Distribution Schematic Drawings UP-9 Distribution Schematic Drawings Distribution Panel Electrical Component Data

15. Vertical Turbine Pump Grease Lubrication System Spares List

Up River Pump Station Equipment Scopes of Supply

Speece Cone Pumps UP‐1/UP‐2/UP‐3 Equipment Scope of Supply

Goulds Pumps Vertical Products Operations

3951 Capitol Avenue

Equipment Scope of Supply ‐ Specification Section 43 21 39 – Pumps: Water, Vertical Turbine

Speece Cone Pumps

Design Criteria Designation: UP‐1/UP‐2/UP‐3

Quantity: Three (3) Units Design Flow: 38,770 GPM Design TDH: 120 Feet Bowl Efficiency: >81.5% Column Pipe Diameter: Thirty–six (36) Inches Discharge Flange: Thirty‐six (36) Inch 150# Raised Face Pattern Motor Horsepower Rating: One Thousand‐Five hundred (1,500) Design Speed: 720 RPM (10P) Motor Voltage: 4160/3/60 (Medium Voltage) Sump Depth: 464.14 Inches (38.68 Feet) Total Pump Length (TPL): 444 Inches (37 Feet)

Discharge Head Assembly Discharge Head Material: ASTM A790 UNS S31803/A181 Gr F51/A240 UNS S31803 Duplex Stainless Steel Discharge Head Design: Above Grade Sealing Method: Packing Packing Material: Acrylic Yarn and Graphite Tension Plate Material: ASTM A479 UNS S31803 Duplex Stainless Steel Head Shaft Material: ASTM A582 Type 416 Stainless Steel Head Shaft Diameter: 3.6875 Inches Head Shaft Coupling Material: ASTM A564 TP630 Cond H1150 Type A 17‐4 PH Stainless Steel Head Shaft Coupling Design: Type A Adjustable Sole Plate Material: ASTM A240 Type 316L Stainless Steel Discharge Head Fastener Material: ASTM A479 UNS S31803 Duplex Stainless Steel Coupling Guard Material: ASTM A240 Type 316L Stainless Steel

Column Assembly Column Piping Material: Duplex Stainless Steel Column Design: Enclosed line shaft Column Piping Configuration: Flanged Line Shaft Material: Type 416 Stainless Steel Line Shaft Diameter: 3.6875 Inches Line Shaft Coupling Material: Type 410 Stainless Steel Line Shaft Coupling Design: Keyed Line Shaft Bearing Material: Modified Federal Alloy III Bronze Enclosing Tube Material: ASTM A790 UNS S31803 Duplex Stainless Steel Column Fastener Material: ASTM A479 UNS S31803 Duplex Stainless Steel

Bowl Assembly Bowl Material: ASTM A890 Grade 1B ACI Type CD4MCuN Bowl Bearing Material: Modified Federal Alloy III Bronze Bowl Wear Ring Material: Type 420 HT CA‐40 Stainless Steel (285‐350 BHN) Sand Collar Material: Duplex Stainless Steel Bowl Shaft Material: Type 416 Stainless Steel Bowl Shaft Diameter: 4.000 Inches Impeller Material: ASTM A890 Grade 1B ACI Type CD4MCuN Impeller Design: Enclosed‐Dynamically Balanced Impeller Wear Ring Material: Type 410 CA‐15 Stainless Steel Suction Bell Material: ASTM A890 Grade 1B ACI Type CD4MCuN Suction Bearing Plug Material: ASTM A240 Type 316L Stainless Steel Bowl Fastener Material: ASTM A276 Type 316L Stainless steel

Corrosion Protection Anti‐Fouling coating of the following pump components:

Exterior: Discharge Head, Column and Bowl Assembly Interior: Discharge Head, Column and Bowl Assembly

Vertical High Thrust Motors Design: Vertical high thrust solid shaft (VSS) Enclosure Rating: Weather Protected‐II Insulation: Class H Efficiency Rating: Premium‐Inverter Duty Ambient Temperature Rating: 40o C Service Factor: 1.15 on sine wave power; 1.00 on VFD power NEMA Design: B Starting Method: VFD Reverse Rotation Protection: Non‐Reverse Ratchet (NRR) Motor Winding Thermal Protection: RTDs (100 Ohm Platinum) with two (2) per phase Motor Bearing Thermal Protection: RTDs (100 Ohm Platinum) with one (1) per bearing Motor Eddy Current Protection: Insulated upper bearing and shaft grounding ring (SGR) Motor Moisture Protection: 115/1/60/700W Space Heaters L‐10 Bearing Life: 100,000 hours based on condition point thrust Vibration Sensor: Metrix 440 Vibration Switch

Pump Spares None.

Motor Spares None.

Special Tools None.

Pump Accessories All pump accessories including pump discharge pressure gauges and air release valves are by others.

Lubricants No motor initial or post start‐up lubricants provided.

Pump Engineering Analysis Lateral and torsional analysis of the pump assemblies

Pump Factory Testing Non‐Witnessed pump bowl assembly full speed performance test per ANSI/H.I. 14.6.5. with a calibrated motor.

Non‐witnessed pump hydrostatic test.

Motor Factory Testing Non‐witnessed complete initial test

Pump/Motor Field Testing Vibration testing by others.

Note: All instrumentation including temporary flow meters is by others.

Controls All controls are by others.

Services Field service for pump installation certification, start‐up, field testing and training.

High Pressure Backwash Pumps UP‐4/UP‐7

Goulds Pumps Vertical Products Operations

3951 Capitol Avenue

High Pressure Screen Backwash Pumps

Designation: UP‐4/UP‐7

Quantity: Two (2) Units Design Flow: 1140 GPM Design TDH: 205 Feet Bowl Efficiency: >75.0% Column Pipe Diameter: Ten (10) Inches Discharge Flange: Ten (10) Inch 150# Raised Face Pattern Motor Horsepower Rating: One hundred (100) Design Speed: 1800 RPM (4P) Motor Voltage: 460/3/60 (Low Voltage) Sump Depth: 464.16 Inches (38.68 Feet) Total Pump Length (TPL): 461.75 Inches (38.48 Feet)

Discharge Head Assembly Discharge Head Material: ASTM A790 UNS S31803/A181 Gr F51/A240 UNS S31803 Duplex Stainless Steel Discharge Head Design: Above Grade Sealing Method: Packing Packing Material: Acrylic Yarn and Graphite Tension Plate Material: ASTM A479 UNS S31803 Duplex Stainless Steel Head Shaft Material: ASTM A582 Type 416 Stainless Steel Head Shaft Diameter: 1.1875 Inches Head Shaft Coupling Material: ASTM A276 Type 316 Stainless Steel Head Shaft Coupling Design: Type A Adjustable Sole Plate Material: ASTM A240 Type 316L Stainless Steel Discharge Head Fastener Material: ASTM A479 UNS S31803 Duplex Stainless Steel Coupling Guard Material: ASTM A240 Type 316L Stainless Steel

Column Assembly Column Piping Material: Duplex Stainless Steel Column Design: Enclosed line shaft Column Piping Configuration: Flanged Line Shaft Material: Type 416 Stainless Steel Line Shaft Diameter: 1.1875 Inches Line Shaft Coupling Material: Type 410 Stainless Steel Line Shaft Coupling Design: Threaded Line Shaft Bearing Material: Modified Federal Alloy III Bronze

Bowl Bearing Material: Modified Federal Alloy III Bronze Bowl Wear Ring Material: Type 420 HT CA‐40 Stainless Steel (285‐350 BHN) Sand Collar Material: Duplex Stainless Steel Bowl Shaft Material: Type 416 Stainless Steel Bowl Shaft Diameter: 1.6875 Inches Impeller Material: ASTM A890 Grade 1B ACI Type CD4MCuN Impeller Design: Enclosed‐Dynamically Balanced Impeller Wear Ring Material: Type 410 CA‐15 Stainless Steel Suction Bell Material: ASTM A890 Grade 1B ACI Type CD4MCuN Suction Bearing Plug Material: ASTM A240 Type 316L Stainless Steel Bowl Fastener Material: ASTM A276 Type 316L Stainless steel

Corrosion Protection Anti‐Fouling coating of the following pump components:

Exterior: Discharge Head, Column and Bowl Assembly Interior: Discharge Head, Column and Bowl Assembly

Vertical High Thrust Motors Design: Vertical high thrust solid shaft (VSS) Enclosure Rating: Weather Protected‐II Insulation: Class H Efficiency Rating: Premium‐Inverter Duty Ambient Temperature Rating: 40o C Service Factor: 1.15 on sine wave power; 1.00 on VFD power NEMA Design: B Starting Method: VFD Reverse Rotation Protection: Non‐Reverse Ratchet (NRR) Motor Winding Thermal Protection: Normally Closed (NC) Thermostats with one (1) per phase Motor Eddy Current Protection: Insulated upper bearing and shaft grounding ring (SGR) Motor Moisture Protection: 115/1/60/192W Space Heaters L‐10 Bearing Life: 100,000 hours based on condition point thrust

Pump Spares None.

Motor Spares None.

Special Tools None.

Pump Accessories All pump accessories including pump discharge pressure gauges and air release valves are by others.

Pump Factory Testing Non‐Witnessed pump bowl assembly full speed performance test per ANSI/H.I. 14.6.5. with a calibrated motor.

Non‐witnessed pump hydrostatic test.

Motor Factory Testing Non‐witnessed complete initial test

Pump/Motor Field Testing

Mixing Water Pumps UP‐5/UP‐8

Goulds Pumps Vertical Products Operations

3951 Capitol Avenue

Mixing Water Pumps

Designation: UP‐5/UP‐8

Quantity: Two (2) Units Design Flow: 1,200 GPM Design TDH: 40 Feet Bowl Efficiency: >73.0% Column Pipe Diameter: Eight (8) Inches Discharge Flange: Eight (8) Inch 150# Raised Face Pattern Motor Horsepower Rating: Twenty (20) Design Speed: 1800 RPM (4P) Motor Voltage: 460/3/60 (Low Voltage) Sump Depth: 464.16 Inches (38.68 Feet) Total Pump Length (TPL): 458.75 Inches (38.23 Feet)

Discharge Head Assembly Discharge Head Material: ASTM A790 UNS S31803/A181 Gr F51/A240 UNS S31803 Duplex Stainless Steel Discharge Head Design: Above Grade Sealing Method: Packing Packing Material: Acrylic Yarn and Graphite Tension Plate Material: ASTM A479 UNS S31803 Duplex Stainless Steel Head Shaft Material: ASTM A582 Type 416 Stainless Steel Head Shaft Diameter: 1.00 Inches Head Shaft Coupling Material: ASTM A276 Type 316 Stainless Steel Head Shaft Coupling Design: Type A Adjustable Sole Plate Material: ASTM A240 Type 316L Stainless Steel Discharge Head Fastener Material: ASTM A479 UNS S31803 Duplex Stainless Steel Coupling Guard Material: ASTM A240 Type 316L Stainless Steel

Column Assembly Column Piping Material: Duplex Stainless Steel Column Design: Enclosed line shaft Column Piping Configuration: Flanged Line Shaft Material: Type 416 Stainless Steel Line Shaft Diameter: 1.00 Inches Line Shaft Coupling Material: Type 410 Stainless Steel Line Shaft Coupling Design: Threaded Line Shaft Bearing Material: Modified Federal Alloy III Bronze

Bowl Bearing Material: Modified Federal Alloy III Bronze Bowl Wear Ring Material: Type 420 HT CA‐40 Stainless Steel (285‐350 BHN) Sand Collar Material: Duplex Stainless Steel Bowl Shaft Material: Type 416 Stainless Steel Bowl Shaft Diameter: 2.1875 Inches Impeller Material: ASTM A890 Grade 1B ACI Type CD4MCuN Impeller Design: Enclosed‐Dynamically Balanced Impeller Wear Ring Material: Type 410 CA‐15 Stainless Steel Suction Bell Material: ASTM A890 Grade 1B ACI Type CD4MCuN Suction Bearing Plug Material: ASTM A240 Type 316L Stainless Steel Bowl Fastener Material: ASTM A276 Type 316L Stainless steel

Corrosion Protection Anti‐Fouling coating of the following pump components:

Exterior: Discharge Head, Column and Bowl Assembly Interior: Discharge Head, Column and Bowl Assembly

Vertical High Thrust Motors Design: Vertical high thrust solid shaft (VSS) Enclosure Rating: Totally Enclosed Fan Cooled Insulation: Class F Efficiency Rating: Premium‐Inverter Duty Ambient Temperature Rating: 40o C Service Factor: 1.15 on sine wave power; 1.00 on VFD power NEMA Design: B Starting Method: VFD Reverse Rotation Protection: Non‐Reverse Ratchet (NRR) Motor Winding Thermal Protection: Normally Closed (NC) Thermostats with one (1) per phase Motor Eddy Current Protection: Insulated upper bearing and shaft grounding ring (SGR) Motor Moisture Protection: 115/1/60/48W Space Heaters L‐10 Bearing Life: 100,000 hours based on condition point thrust

Pump Spares None.

Motor Spares None.

Special Tools None.

Pump Accessories All pump accessories including pump discharge pressure gauges and air release valves are by others.

Pump Factory Testing Non‐Witnessed pump bowl assembly full speed performance test per ANSI/H.I. 14.6.5. with a calibrated motor.

Non‐witnessed pump hydrostatic test.

Motor Factory Testing Non‐witnessed complete initial test

Pump/Motor Field Testing

Low Pressure Backwash Pumps UP‐6/UP‐9

Goulds Pumps Vertical Products Operations

3951 Capitol Avenue

Low Pressure Screen Backwash Pumps

Designation: UP‐6/UP‐9

Quantity: Two (2) Units Design Flow: 1,755 GPM Design TDH: 80 Feet Bowl Efficiency: >73.0% Column Pipe Diameter: Ten (10) Inches Discharge Flange: Ten (10) Inch 150# Raised Face Pattern Motor Horsepower Rating: Sixty (60) Design Speed: 1800 RPM (4P) Motor Voltage: 460/3/60 (Low Voltage) Sump Depth: 464.16 Inches (38.68 Feet) Total Pump Length (TPL): 459.88 Inches (38.32 Feet)

Discharge Head Assembly Discharge Head Material: ASTM A790 UNS S31803/A181 Gr F51/A240 UNS S31803 Duplex Stainless Steel Discharge Head Design: Above Grade Sealing Method: Packing Packing Material: Acrylic Yarn and Graphite Tension Plate Material: ASTM A479 UNS S31803 Duplex Stainless Steel Head Shaft Material: ASTM A582 Type 416 Stainless Steel Head Shaft Diameter: 1.1875 Inches Head Shaft Coupling Material: ASTM A276 Type 316 Stainless Steel Head Shaft Coupling Design: Type A Adjustable Sole Plate Material: ASTM A240 Type 316L Stainless Steel Discharge Head Fastener Material: ASTM A479 UNS S31803 Duplex Stainless Steel Coupling Guard Material: ASTM A240 Type 316L Stainless Steel

Column Assembly Column Piping Material: Duplex Stainless Steel Column Design: Enclosed line shaft Column Piping Configuration: Flanged Line Shaft Material: Type 416 Stainless Steel Line Shaft Diameter: 1.1875 Inches Line Shaft Coupling Material: Type 410 Stainless Steel Line Shaft Coupling Design: Threaded Line Shaft Bearing Material: Modified Federal Alloy III Bronze

Bowl Bearing Material: Modified Federal Alloy III Bronze Bowl Wear Ring Material: Type 420 HT CA‐40 Stainless Steel (285‐350 BHN) Sand Collar Material: Duplex Stainless Steel Bowl Shaft Material: Type 416 Stainless Steel Bowl Shaft Diameter: 1.9375 Inches Impeller Material: ASTM A890 Grade 1B ACI Type CD4MCuN Impeller Design: Enclosed‐Dynamically Balanced Impeller Wear Ring Material: Type 410 CA‐15 Stainless Steel Suction Bell Material: ASTM A890 Grade 1B ACI Type CD4MCuN Suction Bearing Plug Material: ASTM A240 Type 316L Stainless Steel Bowl Fastener Material: ASTM A276 Type 316L Stainless steel

Corrosion Protection Anti‐Fouling coating of the following pump components:

Exterior: Discharge Head, Column and Bowl Assembly Interior: Discharge Head, Column and Bowl Assembly

Vertical High Thrust Motors Design: Vertical high thrust solid shaft (VSS) Enclosure Rating: Totally Enclosed Fan Cooled Insulation: Class F Efficiency Rating: Premium‐Inverter Duty Ambient Temperature Rating: 40o C Service Factor: 1.15 on sine wave power; 1.00 on VFD power NEMA Design: B Starting Method: VFD Reverse Rotation Protection: Non‐Reverse Ratchet (NRR) Motor Winding Thermal Protection: Normally Closed (NC) Thermostats with one (1) per phase Motor Eddy Current Protection: Insulated upper bearing and shaft grounding ring (SGR) Motor Moisture Protection: 115/1/60/144W Space Heaters L‐10 Bearing Life: 100,000 hours based on condition point thrust

Pump Spares None.

Motor Spares None.

Special Tools None.

Pump Accessories All pump accessories including pump discharge pressure gauges and air release valves are by others.

Pump Factory Testing Non‐Witnessed pump bowl assembly full speed performance test per ANSI/H.I. 14.6.5. with a calibrated motor.

Non‐witnessed pump hydrostatic test.

Motor Factory Testing Non‐witnessed complete initial test

Pump/Motor Field Testing

Vertical Turbine Pump Sample Nameplate

H��� Mounted Nameplate

$�j?

��{X�

��X��{X� j�����

�X��� j @�����X|

$��^~�jX$@ @?��@�$@��j�$$}j� j��

$}�@?X{ j��}?�@

?@���{X� jX@Xj��?�@ j jX@ @?X{

�X}��$��}��$

()9��7 BC� (����� �� ��� ��

��)* BC� "��

� ��I�

� ��I� *C&)7 3�

9�3�*� 9�

9��)& -7CD 9�

(?"��CB B<�

F)�9 �?�7� F���

A

B

C

D

A

B

C

D

ITT

GOULDS PUMPS

Engineered for lifeITT

GOULDS PUMPS

Engineered for lifeITT

GOULDS PUMPS

Engineered for life

1.50 0.06

0.28

0.125

0.25

0.04

6.50

5.00

LTR ZONE REVISION BY DATE

ORDER NO.:

QUANTITY:

BY:

DATE:

REMARKS

NO ENGINEERING NOTES

TEMPERATURE BASIS FOR M.A.W.P SHALL

BE INCLUDED

WHEN DESIGN INCLUDES THRUST POT,

BEARING IDENTIFICATION PER GOULDS

DRAWING NUMBER SHALL BE INCLUDED.

3 USE ADDITIONAL PLATES AS NEEDED.

SERIAL NO.

P.O. NO.

R.P.M.

MODEL

M.A.W.P. DISCH.

RATED FLOW

M.A.W.P. SUCT.

CASE HYDROSTATIC TEST PRESSURE

DISCHARGE

SUCTION

YEAR BUILT

ITEM NO.

LIFT ROTOR

SIZE

RATED HEAD

INSPECTED BY

www.gouldspumps.com

ROTATION

NP105_06

PLACE SMALL MARK AT THIS POINT

STANDARD PLATE THICKNESS 0.040 �#� 0.005

HORIZONTAL GRAIN. MATERIAL 316 SS.

BACKGROUND GRAY.

ITT LOGO YELLOW.

315410

110426.P.006

44GHC- 1 STAGE

38770 GPM 120.0 FT

86.5 PSIG

129.7 PSIG

SERVICE: UPRIVER RAW WATER PUMPS

ITT

Goulds Pumps

ASSEMBLED IN USA

315410

SANTHOSH

05-09-16

UP-1

UP-2

UP-3

SCALE

NONE

LTR ZONE REVISION BY DATE

DRAWN BY DATE CHECKED BY DATE

SANTHOSH 05-09-16 S.WEBSTER 05-09-16

TITLE

NAMEPLATE, STANDARD

PATTERN NUMBER

DRAWING NUMBER

PND315410

LTR ZONE REVISION BY DATE

TOLERANCES EXCEPT AS NOTED:

DECIMALS: .000 = �#�.010 [0,254]

.00 = �#�.032 [0,813] .0 = �#�.062 [1,575]

ANGLES: �#� 1/4 DEGREE

CONCENTRICITY: MAX T.I.R. BETWEEN

ANY TWO CONCENTRIC DIAMETERS

IS 1/2 THEIR MAX TOLERANCE

SQUARENESS:

MACHINED FACES MUST BE

PARALLEL WITH EACH OTHER

AND PERPENDICULAR TO MACHINED

DIAMETERS WITHIN .002 [0,051]T.I.R.

BREAK ALL SHARP EDGES .005-.015

[0,127-0,381]

DIMENSIONS IN [ ] ARE IN MILIMETERS

DRAWN BY DATE CHECKED BY DATE

TITLE

PATTERN NUMBER

DRAWING NUMBER

LTR ZONE REVISION BY DATE

DRAWN BY DATE CHECKED BY DATE

TITLE

PATTERN NUMBER

DRAWING NUMBER

LTR ZONE REVISION BY DATE

DRAWN BY DATE CHECKED BY DATE

TITLE

PATTERN NUMBER

DRAWING NUMBER

LTR ZONE REVISION BY DATE

THIS DOCUMENT CONTAINS CONFIDENTIAL AND

TRADE SECRET INFORMATION WHICH IS THE

PROPERTY OF THE VERTICAL PRODUCTS, DIVISION

OF GOULDS PUMPS, INC. AND RECEIPT OR

POSSESION DOES NOT CONVEY ANY RIGHTS TO

LOAN, SELL, OR OTHERWISE DISCLOSE SAID

INFORMATION, REPRODUCTION OR USE OF SAID

INFORMATION FOR ANY PURPOSE OTHER THAN

THAT IN CONNECTION WITH WHICH SAID

INFORMATION WAS SUPPLIED MAY NOT BE MADE

WITHOUT EXPRESS WRITTEN PERMISSION OF

GOULDS PUMPS VERTICAL PRODUCTS DIVISION.

THIS DOCUMENT IS TO BE RETURNED TO THE

VERTICAL PRODUCTS DIVISION UPON REQUEST

AND IN ALL EVENTS UPON COMPLETION OF

THE PURPOSE FOR WHICH IT IS LOANED.

AFTER IMPELLER

US PATENT NO.9046107 APPLIES

Engineered Systems Los Angeles

SPINS FREELY

0.375 IN BUILT IN

SEE REMARKS

VIT-FF

A

B

C

D

A

B

C

D

ITT

GOULDS PUMPS

Engineered for lifeITT

GOULDS PUMPS

Engineered for lifeITT

GOULDS PUMPS

Engineered for life

1.50 0.06

0.28

0.125

0.25

0.04

6.50

5.00

LTR ZONE REVISION BY DATE

ORDER NO.:

QUANTITY:

BY:

DATE:

REMARKS

NO ENGINEERING NOTES

TEMPERATURE BASIS FOR M.A.W.P SHALL

BE INCLUDED

WHEN DESIGN INCLUDES THRUST POT,

BEARING IDENTIFICATION PER GOULDS

DRAWING NUMBER SHALL BE INCLUDED.

3 USE ADDITIONAL PLATES AS NEEDED.

SERIAL NO.

P.O. NO.

R.P.M.

MODEL

M.A.W.P. DISCH.

RATED FLOW

M.A.W.P. SUCT.

CASE HYDROSTATIC TEST PRESSURE

DISCHARGE

SUCTION

YEAR BUILT

ITEM NO.

LIFT ROTOR

SIZE

RATED HEAD

INSPECTED BY

www.gouldspumps.com

ROTATION

NP105_06

PLACE SMALL MARK AT THIS POINT

STANDARD PLATE THICKNESS 0.040 �#� 0.005

HORIZONTAL GRAIN. MATERIAL 316 SS.

BACKGROUND GRAY.

ITT LOGO YELLOW.

315411

110426.P.006

12JHC- 4 STAGES

1140 GPM 205,1 FT

132.8 PSIG

199.2 PSIG

Goulds Pumps

ASSEMBLED IN USA

315411

SANTHOSH

05-09-16

UP-4

UP-7

SCALE

NONE

LTR ZONE REVISION BY DATE

DRAWN BY DATE CHECKED BY DATE

SANTHOSH 05-09-16 S.WEBSTER 05-09-16

TITLE

NAMEPLATE, STANDARD

PATTERN NUMBER

DRAWING NUMBER

PND315411

LTR ZONE REVISION BY DATE

TOLERANCES EXCEPT AS NOTED:

DECIMALS: .000 = �#�.010 [0,254]

.00 = �#�.032 [0,813] .0 = �#�.062 [1,575]

ANGLES: �#� 1/4 DEGREE

CONCENTRICITY: MAX T.I.R. BETWEEN

ANY TWO CONCENTRIC DIAMETERS

IS 1/2 THEIR MAX TOLERANCE

SQUARENESS:

MACHINED FACES MUST BE

PARALLEL WITH EACH OTHER

AND PERPENDICULAR TO MACHINED

DIAMETERS WITHIN .002 [0,051]T.I.R.

BREAK ALL SHARP EDGES .005-.015

[0,127-0,381]

DIMENSIONS IN [ ] ARE IN MILIMETERS

DRAWN BY DATE CHECKED BY DATE

TITLE

PATTERN NUMBER

DRAWING NUMBER

LTR ZONE REVISION BY DATE

DRAWN BY DATE CHECKED BY DATE

TITLE

PATTERN NUMBER

DRAWING NUMBER

LTR ZONE REVISION BY DATE

DRAWN BY DATE CHECKED BY DATE

TITLE

PATTERN NUMBER

DRAWING NUMBER

LTR ZONE REVISION BY DATE

THIS DOCUMENT CONTAINS CONFIDENTIAL AND

TRADE SECRET INFORMATION WHICH IS THE

PROPERTY OF THE VERTICAL PRODUCTS, DIVISION

OF GOULDS PUMPS, INC. AND RECEIPT OR

POSSESION DOES NOT CONVEY ANY RIGHTS TO

LOAN, SELL, OR OTHERWISE DISCLOSE SAID

INFORMATION, REPRODUCTION OR USE OF SAID

INFORMATION FOR ANY PURPOSE OTHER THAN

THAT IN CONNECTION WITH WHICH SAID

INFORMATION WAS SUPPLIED MAY NOT BE MADE

WITHOUT EXPRESS WRITTEN PERMISSION OF

GOULDS PUMPS VERTICAL PRODUCTS DIVISION.

THIS DOCUMENT IS TO BE RETURNED TO THE

VERTICAL PRODUCTS DIVISION UPON REQUEST

AND IN ALL EVENTS UPON COMPLETION OF

THE PURPOSE FOR WHICH IT IS LOANED.

AFTER IMPELLER

US PATENT NO.9046107 APPLIES

Engineered Systems Los Angeles

SPINS FREELY

0.187 IN BUILT IN

SEE REMARKS

A

B

C

D

A

B

C

D

ITT

GOULDS PUMPS

Engineered for lifeITT

GOULDS PUMPS

Engineered for lifeITT

GOULDS PUMPS

Engineered for life

1.50 0.06

0.28

0.125

0.25

0.04

6.50

5.00

LTR ZONE REVISION BY DATE

ORDER NO.:

QUANTITY:

BY:

DATE:

REMARKS

NO ENGINEERING NOTES

TEMPERATURE BASIS FOR M.A.W.P SHALL

BE INCLUDED

WHEN DESIGN INCLUDES THRUST POT,

BEARING IDENTIFICATION PER GOULDS

DRAWING NUMBER SHALL BE INCLUDED.

3 USE ADDITIONAL PLATES AS NEEDED.

SERIAL NO.

P.O. NO.

R.P.M.

MODEL

M.A.W.P. DISCH.

RATED FLOW

M.A.W.P. SUCT.

CASE HYDROSTATIC TEST PRESSURE

DISCHARGE

SUCTION

YEAR BUILT

ITEM NO.

LIFT ROTOR

SIZE

RATED HEAD

INSPECTED BY

www.gouldspumps.com

ROTATION

NP105_06

PLACE SMALL MARK AT THIS POINT

STANDARD PLATE THICKNESS 0.040 �#� 0.005

HORIZONTAL GRAIN. MATERIAL 316 SS.

BACKGROUND GRAY.

ITT LOGO YELLOW.

315412

110426.P.006

12ELC- 1 STAGE

1200 GPM 40.0 FT

39.5 PSIG

59.2 PSIG

Goulds Pumps

ASSEMBLED IN USA

315412

SANTHOSH

05-09-16

UP-5

UP-8

SCALE

NONE

LTR ZONE REVISION BY DATE

DRAWN BY DATE CHECKED BY DATE

SANTHOSH 05-09-16 S.WEBSTER 05-09-16

TITLE

NAMEPLATE, STANDARD

PATTERN NUMBER

DRAWING NUMBER

PND315412

LTR ZONE REVISION BY DATE

TOLERANCES EXCEPT AS NOTED:

DECIMALS: .000 = �#�.010 [0,254]

.00 = �#�.032 [0,813] .0 = �#�.062 [1,575]

ANGLES: �#� 1/4 DEGREE

CONCENTRICITY: MAX T.I.R. BETWEEN

ANY TWO CONCENTRIC DIAMETERS

IS 1/2 THEIR MAX TOLERANCE

SQUARENESS:

MACHINED FACES MUST BE

PARALLEL WITH EACH OTHER

AND PERPENDICULAR TO MACHINED

DIAMETERS WITHIN .002 [0,051]T.I.R.

BREAK ALL SHARP EDGES .005-.015

[0,127-0,381]

DIMENSIONS IN [ ] ARE IN MILIMETERS

DRAWN BY DATE CHECKED BY DATE

TITLE

PATTERN NUMBER

DRAWING NUMBER

LTR ZONE REVISION BY DATE

DRAWN BY DATE CHECKED BY DATE

TITLE

PATTERN NUMBER

DRAWING NUMBER

LTR ZONE REVISION BY DATE

DRAWN BY DATE CHECKED BY DATE

TITLE

PATTERN NUMBER

DRAWING NUMBER

LTR ZONE REVISION BY DATE

THIS DOCUMENT CONTAINS CONFIDENTIAL AND

TRADE SECRET INFORMATION WHICH IS THE

PROPERTY OF THE VERTICAL PRODUCTS, DIVISION

OF GOULDS PUMPS, INC. AND RECEIPT OR

POSSESION DOES NOT CONVEY ANY RIGHTS TO

LOAN, SELL, OR OTHERWISE DISCLOSE SAID

INFORMATION, REPRODUCTION OR USE OF SAID

INFORMATION FOR ANY PURPOSE OTHER THAN

THAT IN CONNECTION WITH WHICH SAID

INFORMATION WAS SUPPLIED MAY NOT BE MADE

WITHOUT EXPRESS WRITTEN PERMISSION OF

GOULDS PUMPS VERTICAL PRODUCTS DIVISION.

THIS DOCUMENT IS TO BE RETURNED TO THE

VERTICAL PRODUCTS DIVISION UPON REQUEST

AND IN ALL EVENTS UPON COMPLETION OF

THE PURPOSE FOR WHICH IT IS LOANED.

AFTER IMPELLER

US PATENT NO.9046107 APPLIES

Engineered Systems Los Angeles

SPINS FREELY

0.187 IN BUILT IN

SEE REMARKS

A

B

C

D

A

B

C

D

ITT

GOULDS PUMPS

Engineered for lifeITT

GOULDS PUMPS

Engineered for lifeITT

GOULDS PUMPS

Engineered for life

1.50 0.06

0.28

0.125

0.25

0.04

6.50

5.00

LTR ZONE REVISION BY DATE

ORDER NO.:

QUANTITY:

BY:

DATE:

REMARKS

NO ENGINEERING NOTES

TEMPERATURE BASIS FOR M.A.W.P SHALL

BE INCLUDED

WHEN DESIGN INCLUDES THRUST POT,

BEARING IDENTIFICATION PER GOULDS

DRAWING NUMBER SHALL BE INCLUDED.

3 USE ADDITIONAL PLATES AS NEEDED.

SERIAL NO.

P.O. NO.

R.P.M.

MODEL

M.A.W.P. DISCH.

RATED FLOW

M.A.W.P. SUCT.

CASE HYDROSTATIC TEST PRESSURE

DISCHARGE

SUCTION

YEAR BUILT

ITEM NO.

LIFT ROTOR

SIZE

RATED HEAD

INSPECTED BY

www.gouldspumps.com

ROTATION

NP105_06

PLACE SMALL MARK AT THIS POINT

STANDARD PLATE THICKNESS 0.040 �#� 0.005

HORIZONTAL GRAIN. MATERIAL 316 SS.

BACKGROUND GRAY.

ITT LOGO YELLOW.

315413

110426.P.006

14JHC- 1 STAGE

1755 GPM 79.9 FT

59.9 PSIG

89.8 PSIG

Goulds Pumps

ASSEMBLED IN USA

315413

SANTHOSH

05-09-16

UP-6

UP-9

SCALE

NONE

LTR ZONE REVISION BY DATE

DRAWN BY DATE CHECKED BY DATE

SANTHOSH 05-09-16 S.WEBSTER 05-09-16

TITLE

NAMEPLATE, STANDARD

PATTERN NUMBER

DRAWING NUMBER

PND315413

LTR ZONE REVISION BY DATE

TOLERANCES EXCEPT AS NOTED:

DECIMALS: .000 = �#�.010 [0,254]

.00 = �#�.032 [0,813] .0 = �#�.062 [1,575]

ANGLES: �#� 1/4 DEGREE

CONCENTRICITY: MAX T.I.R. BETWEEN

ANY TWO CONCENTRIC DIAMETERS

IS 1/2 THEIR MAX TOLERANCE

SQUARENESS:

MACHINED FACES MUST BE

PARALLEL WITH EACH OTHER

AND PERPENDICULAR TO MACHINED

DIAMETERS WITHIN .002 [0,051]T.I.R.

BREAK ALL SHARP EDGES .005-.015

[0,127-0,381]

DIMENSIONS IN [ ] ARE IN MILIMETERS

DRAWN BY DATE CHECKED BY DATE

TITLE

PATTERN NUMBER

DRAWING NUMBER

LTR ZONE REVISION BY DATE

DRAWN BY DATE CHECKED BY DATE

TITLE

PATTERN NUMBER

DRAWING NUMBER

LTR ZONE REVISION BY DATE

DRAWN BY DATE CHECKED BY DATE

TITLE

PATTERN NUMBER

DRAWING NUMBER

LTR ZONE REVISION BY DATE

THIS DOCUMENT CONTAINS CONFIDENTIAL AND

TRADE SECRET INFORMATION WHICH IS THE

PROPERTY OF THE VERTICAL PRODUCTS, DIVISION

OF GOULDS PUMPS, INC. AND RECEIPT OR

POSSESION DOES NOT CONVEY ANY RIGHTS TO

LOAN, SELL, OR OTHERWISE DISCLOSE SAID

INFORMATION, REPRODUCTION OR USE OF SAID

INFORMATION FOR ANY PURPOSE OTHER THAN

THAT IN CONNECTION WITH WHICH SAID

INFORMATION WAS SUPPLIED MAY NOT BE MADE

WITHOUT EXPRESS WRITTEN PERMISSION OF

GOULDS PUMPS VERTICAL PRODUCTS DIVISION.

THIS DOCUMENT IS TO BE RETURNED TO THE

VERTICAL PRODUCTS DIVISION UPON REQUEST

AND IN ALL EVENTS UPON COMPLETION OF

THE PURPOSE FOR WHICH IT IS LOANED.

AFTER IMPELLER

US PATENT NO.9046107 APPLIES

Engineered Systems Los Angeles

SPINS FREELY

0.187 IN BUILT IN

SEE REMARKS

Vertical High Thrust Solid Shaft Motor Sample Nameplate

REV

AOF

DWG NO.CODE

ISSUED BY APPROVED BY

TITLEREVISION DESCRIPTION FOR:

mmINCHES

SCALE UNITS

SOLIDEDGE

MATERIAL:

DWG

SIZE

SHEET

NUMBER

TOLERANCES ON DIMENSIONS

(UNLESS OTHERWISE SPECIFIED)

ANGLES X°= ±1°

NIDEC CONFIDENTIAL

NMCA (OCT-2013)

NIDEC MOTOR CORPORATION 28-Feb-14

REVISION DATE

NIDEC MOTOR

CORPORATION

ITEMS AND MATERIALS SPECIFIED HEREIN MUST

COMPLY WITH THE EUROPEAN REDUCTION OF

HAZARDOUS SUBSTANCES (RoHS 2) DIRECTIVE

2011/65/EU, REGULATIONS (EC) NO. 1907/2006

("REACH") AS OF 1 JUNE 2007 AND ALL

SUBSEQUENT UPDATES. PLEASE REFER TO

THE OFFICIAL EU DOCUMENTS FOR COMPLETE

DEFINITION, RESTRICTIONS, AND LIMITS FOR

EACH SUBSTANCE.

COLORS :

BLACK : LINES, LETTERS AND NUMBERS

RED : THE BACKGROUND BEHIND "US"

IN LOGO

2B FINISH : BACKGROUND

MATERIAL :

MIN. #28 GA. (.0149)

MAX. #27 GA. (.0164)

#304-2B STAINLESS STEEL

SIZE :

OVERALL HORIZONTAL ........... : 4.00

OVERALL VERTICAL ................. : 3.00

CORNER RADII .......................... : .13 R

NOTE TO SUPPLIER :

THIS PLATE TO BE MADE AS SHOWN IN

ILLUSTRATION.

NOTES :

1. PLATE TO BE ETCHED.

UPDATED AGENCY MARKINGS.

ECO A1007-50

NAMEPLATE, BLANK

F

J. HAGENER. KING

INNONE

28-FEB-14

0422707

SEE NOTE

CSTG NO.

PART NO. FRAME

SEE TABLE ---

TYPE

NAMEPLATE

PART NUMBER

422707-001 422707-005

YES

NO

CATALOG #

LOWER

END BRG

FR

PH

INSUL

CLASS

HP

MAX

AMB

DUTY

°C ID#

WT

TYPE

RPM

UPPER

END BRG

MODEL #

ENCL

BAL

AMPS

VOLTS

HZSF

CODE DES

AMPS

NEMA NOM

EFFICIENCY

I N V E R T E R D U T Y

MAX

KVAR

.266

.040

DETAIL A

3.625

AREA FOR PART

NUMBER PER TABLE

SEE DETAIL A

.1252 X O

422707-006 422707-008

.125

PF

OIL CAPACITY QTS. QTS.LOWER

END BRG

UPPER

END BRG

TORQUE HZ RANGE MAX RPM

LB-FT

INV. TYPESF 1.0

MADE IN OF IMPORTED AND DOMESTIC COMPONENTS

R

NIDEC MOTOR

CORPORATION

.188.250

R

E51488

NEMA MG1

PART 31

www.usmotors.com

MARKINGS TO BE

RIGHT JUSTIFIED

AND ADDED FROM

RIGHT TO LEFT

PER TABLE

PART NUMBER INCLUDES

THESE AGENCY MARKINGS

R

E51488

R

191252

NONONO

NO

NO

NO

NO

NO

NO

YES

NO

YES

NO

YES

191252

R

ENERGY

R

C US

E51488

Vertical Turbine Pump Curves

Single Line Curve

Model: VIT Size: 44GHC 60Hz RPM: 710 Stages: 1

UP-2/UP-3

0��"�"!��� � �� �.(1 '( ((�'2 ��"��� '3�(,�2'(1

����� ,(43(' ( , Operating Conditions Pump Performance 5!��!�� +�"��

�� �%��6���!�:�

�A�� 34 (�$"

Notes: ( ��6�%�"���"�&)���"�����$$��"�����)��$��&�����������"�!��6����

Model: VIT Size: 44GHC 60Hz RPM Variable Stages: 1

Job/Inq.No. :

Purchaser : CDM CONSTRUCTORS INC.

End User : ACOE-City of Savannah Issued by : Timothy Brandt Item/Equip.No. : Upriver Raw Water Pumps UP-1/

UP-2/UP-3

Quotation No. : TB16-01-11 02 Date : 05/07/2016

Service : Raw Water Order No. : 110426.P.006 Certified By : Rev. : 0 Operating Conditions Pump Performance @ 710 RPM Liquid: Water Published Efficiency: 89.9 % Specific Speed 1st stg: 4,232 gpm(US) ft Temp.: 70.0 deg F Rated Pump Efficiency: 86.6 % Specific Speed Adl stg: 4,232 gpm(US) ft S.G./Visc.: 1.000/1.000 cp Rated Total Power: 1,356.5 hp Min. Hydraulic Flow: 20,357.6 gpm Flow: 38,770.0 gpm Non-Overloading Power: 1,378.6 hp TDH: 120.0 ft Imp. Dia. First 1 Stg(s): 29.28 in NPSHa: 45.1 ft NPSHr: 34.5 ft Solid size: Shut off Head: 190.5 ft % Susp. Solids (by wtg):

Vapor Press:

Max. Solids Size: 5.8700 in

Notes: 1 . Elevated temperature effects on performance are not included.

mbrandt Typewritten Text ***Preliminary minimum speed to maintain 8,000# thrust requirement

Model: VIT Size: 12JHC 60Hz RPM: 1780 Stages: 4

UP-7

2��"�"!��� � �� �0(3 '( ((�'4 ��"��� ',�(5�4'(3

���%!���� 6!7�� ���������������0��8*���

����� 5(9,(( ( 4 Operating Conditions Pump Performance

�� �%��;���!�7�

�6�� ,5 ,�$"

/�#�*"71� B�)��� Notes: ( ��;�%�"���"�&)���"�����$$��"�����)��$��&�����������"�!��;����

Model: VIT Size: 12ELC 60Hz RPM: 1780 Stages: 1

UP-8

2��"�"!��� � �� �0(3 '( ((�'4 ��"��� '5�(6�4'(3

���%!���� �!7!�8�+�"��

����� 6(,5(4 ( 4 Operating Conditions Pump Performance 9!��!�� +�"��

�� �%��:���!�8�

�C�� 56 '�$"

/�#�*"81� B�)��� Notes: ( ��:�%�"���"�&)���"�����$$��"�����)��$��&�����������"�!��:����

Model: VIT Size: 14JHC 60Hz RPM: 1780 Stages: 1

UP-9

2��"�"!��� � �� �0(, '( ((�'3 ��"��� '4�(5�3'(, ���%!���� 6�*� ���������������0��7*���

����� 5(84(5 ( 3 Operating Conditions Pump Performance 6!��!�� +�"��

�� �%��9���!�<�

�C�� 45 (�$"

/�#�*"<1� B�)��� Notes: ( ��9�%�"���"�&)���"�����$$��"�����)��$��&�����������"�!��9����

Vertical Turbine Pump Data

Pump Data

May 5, 2016

CDM CONSTRUCTORS INC.

P.O. NO: 110426.P.006

Product Number: 315410 Proposal No: TB16-01-11 02 Item No: Upriver Raw Water Pumps UP-1/UP-2/UP-3

MODEL: VIT Size: 36 x 44GHC 1 STAGES QTY:3 Pump Design:ANSI/HI 2.3-2008 (Commercial Design Std.)

Operating Conditions SERVICE Raw Water LIQUID Water (70.0 deg F) SP.GR 1.000 Viscosity 1.000 cp LIQUID TYPE Non Toxic CAPACITY 38,770.0 gpm RATED HEAD 120.0 ft SUMP DEPTH 38.68 (ft) (Pumping level 23.22 ft) NPSHa 45.1 ft at 1st imp.eye

Performance at 710 RPM Shut-off Min. Flow Design

Flow(1) Run Out

Flow FLOW RATE (gpm) -0- 20357.6 38770.0 47341.8 TDH (ft) 190.6 141.1 120.1 97.5

PUMP EFFY (%) -0- 58.8 84.0 82.9

POWER (hp) 1258.6 1231.7 1398.7 1406.5 NPSHr (ft) (2) 26.1 34.8 44.8 DOWN THRUST (Lb) 42110.2 NA 27627.8 23050.7 DISCH. PRESS. (psi g) (3) 71.1 40.6 MIN REQ.SUBMERG.(in) (4) 66.6 88.4 96.2

(1) Guaranteed Values

(2) First stage impeller eye elevation

(3) Pressure at Discharge centerline

(4) for vortex suppression, based on H.I. 1994 Edition

MAWP values Bowl - Std 86.5 psi g Column 86.5 psi g Disch.Head, Disch.Side 86.5 psi g Seal Hsg/Piping 86.5 psi g

Materials and Dimensions Bowl Assy BOWL ASTM A890 Grade 1B ACI Type CD4MCUN standard SUCTION BELL ASTM A890 Grade 1B ACI Type CD4MCUN IMPELLER ASTM A890 Grade 1B ACI Type CD4MCUN (Enclosed) keyed to the shaft, dynamically balanced to

8W/N BOWL SHAFT ASTM A582 Type 416 4.0000 (in) diameter

SUCTION BELL BEARING Federal Alloy III (Modified) BOWL BEARINGS Federal Alloy III (Modified) BOWL WEAR RINGS Type 420 HT CA-40 Stainless Steel (285-350 BHN) Set screwed IMPELLER WEAR RINGS Type 410 CA-15 Stainless Steel Set screwed

BOWL BOLTING ASTM A276 TP 316L

BOWL FEATURES

Grease return lines back to mounting plate, 316 Stainless Steel tubing Special design discharge bowl to relieve the injected grease Suction bearing housing plug material 316L Stainless Steel

Column Assy COLUMN ASTM A790 UNS S31803 / A240 UNS S31803 36.00 (in) diameter, 30.53 (ft) long Flanged

COLUMN BOLTING ASTM A479 UNS S31803

COLUMN SHAFT ASTM A582 Type 416, 3.6875 (in) diameter (enclosed) lineshaft sleeve: none ENCLOSING TUBE BRG Federal Alloy III (Modified), 5ft spacing ENCLOSING TUBE ASTM A790 UNS S31803, 8.0000 (in) diam., tube fluid: Grease LINESHAFT CPLG ASTM A276 Type 410 Cond T, Keyed TPL 37.01 (ft)

Head Assy DISCHARGE HEAD ASTM A790 UNS S31803 / A182 Gr F51 / A240 UNS S31803 O-Head

HEAD BOLTING ASTM A479 UNS S31803

HEADSHAFT MATERIAL ASTM A582 Type 416, 3.6875 (in) HEADSHAFT CPLG ASTM A564 TP630 Cond H1150 Type A adjustable COUPLING GUARD 316L Stainless Steel DISCHARGE FLANGE 36 (in) 150# R.F.

HEAD FEATURES

ASTM A240 TP 316L Sole Plate Special Name plates

Sealing Method PACKING Acrylic yarn and graphite

TENSION PLATE ASTM A479 UNS S31803

Engineering Analysis Rotor Torsional Critical Frequency Analysis (complete pump & driver) (FEA) Structural Natural Frequency Analysis (complete pump & driver) (FEA) - for ESLA Internal Use Rotor Lateral Critical Frequency Analysis (complete pump & drive) (FEA)

Testing Assembled Pump Performance Test (Non-Witness) with calibrated customer motor 60 Hz and lab packing box Hydro Test Discharge Head (Non-Witness)

(Test acceptance criteria per ANSI/HI 14.6-2011, grade 2B)

Coatings Anti-Fouling Coating Bowl Interior & Exterior Anti-Fouling Coating Column Interior & Exterior Anti-Fouling Coating Discharge Head Interior Anti-Fouling Coating Enclosing Tube Exterior

Miscellaneous Upriver Grease Lubrication Systems & Start-Up

Proposal No: TB16-01-11 02 Item No: Upriver Raw Water Pumps UP-1/UP-2/UP-3 MODEL: VIT 44GHC

Must comply with Buy American Act

Sacrificial anodes are specified as recommended by pump manufacturer. Since we are including the anti-fouling coating, sacrificial anodes will not be recommended.

Coating material should be by International, as follows (tech sheet attached):

a.Preparation: SSPC-SP10 b.Primer: Intershield 300V with two (2) coats each of 5-7 mils DFT c.Intermediate Coat: Intersleek 381 with one coat of 3-5 mile DFT d.Top Coat: Intersleek 425 one coat with a 6 mil DFT

Driver : Electric motor Vertical solid shaft Manufacturer : Nidec (US Motors) FURNISHED BY Pump mfg MOUNTED BY Customer RATING 1,500.0 hp ENCLOSURE TEAAC PHASE/FREQ/VOLTS 3/60 Hz/4160 SPEED 720 RPM INSULATION/SF F/1.15 FRAME/BD 8011PH/42 (in) VAR. SPEED RANGE 568 / 710 rpm

Driver Features 100,000 Hour Bearing Life Bearing RTDs Complete Motor Test (Non-Witnessed) Driver Calibration Motor freight Non-reverse ratchet Reed frequency data required Space Heater Suitable for VFD Vibration Sensors-Metrix 440 Dual Set Point Winding RTDs (3 Per Phase)

Weights Total Bowl Weight 8,340.0 (lb)

Total Column Weight 8,000.0 (lb)

Discharge Head Weight 4,400.0 (lb)

Driver Weight 9,000.0 (lb)

Total Unit Weight 29740.0 (lb)

Comments

Program Version 1.57.0.

Proposal No: TB16-01-11 02 Item No: Upriver Raw Water Pumps UP-1/UP-2/UP-3 MODEL: VIT 44GHC

Judy.Leong Text Box

Hydraulic Details Item No Upriver Raw Water Pumps UP-1/UP-2/UP-3 Pump Type VIT Proposal # TB16-01-11 02 SO # 315410-1-3

Liquid Characteristics Hydraulic Requirements

Service Raw Water Rated capacity 38,770.0 gpm Liquid Water Rated Head (TDH) 120.0 ft Specific Gravity 1.000 Total sump depth 38.68 ft Temperature 70.0 deg F NPSHa 45.1 ft Viscosity/Solids size 1.000 cp Suction Press./Differential 0.0 / 40.6 psi g

Pumping level 23.22 ft Bowl Performance curve readings at 710 RPM 1st stage Additional stage(s) Bowl size 44GHC Curve No E6144GAPC4-1 No of stages 1 0 (0 Std, 0 Hi, 0 Lag) Rated Head (ft) 121.8 0.0 Rated effy/corrected effy (%) 89.9/88.1 0.0/0.0 Impeller trim (in) 29.28 NPSH required RT/RO (ft) 34.8/44.8 Capacity @ RO (gpm) 47,337.1 RO head (ft) 100.1 0.0 RO effy corrected (%) 87.9 0.0 Shut off head (ft) 190.5 0.0 Shut off power (hp) 1,258.2 total Bowl material correction factor - 0.00 Impeller material correction factor 0.99 0.00 Flow viscosity correction factor (rated) 1.000 1.000 Head viscosity correction factor (rated) 1.000 1.000 Efficiency viscosity correction factor (rated) 1.000 1.000

Efficiency derate 1.0 Min Req.Submergence @ RT/RO (in) 88.41/96.24 Maximum Allowable Working Press. (Suction) 0.0 Max. Allow. Working Press.(Disch.Head,Disch.Side) 86.5 Maximum Allowable Working Press. (Bowl) 86.5 Maximum Allowable Working Press. (Column) 86.5 Max. Allowable Working Press. (Seal Hsg/Piping) 86.5 Hydrotest Press. For Bowl Assy 129.7 Hydrotest Press. For Column 129.7 Hydrotest Press. For Disch.Head, Disch.Side 129.7 Hydrotest Press. For Seal Hsg / Piping 129.7 Duration (min) 5 Allowable column friction loss per 100 ft column 10.0 Allowable column velocity limitation (ft/sec) 16.0 Allowable head friction loss (ft) 2.5

Pump Performance/Dimension Shut-off Rated Run-out Power (hp) 1,258.2 1,356.5 1,363.9 Pressure @ discharge flange (psi g) 71.1 40.6 Total thrust (Lb) 42,101.9 27,621.8 23,045.3 Thrust Bearing Loss (hp) 1.47 1.23 Pump efficiency (%) 86.6 62.1 Total Hydraulic losses (ft) 1.73 2.59 Total pump head @ disch.bowl (ft) 192.27 121.85 100.14 Pressure @ discharge bowl (psi g) 83.23 52.75 43.35 Min. Hydraulic / Thermal flow (gpm) 20,357.6 / N/A Total pump length (in) 444.07

Bowl Dimensions and Characteristics Number of stages 1 (1 Std, 0 High, 0 Lag) Bowl size/material 44GHC / - CD4MCuN Dimensions

1st stage Additional stage(s) Bowl length (in) 46.0000 0.0000 Bowl diameter (in) 45.7500 0.0000 Bowl thickness 0.8700 0.0000 Bowl lateral (in) 1.2500 0.0000 Bowl throat diameter (in) 25.1200

Bell diameter (in) 47.0000 Bell length to bell lip (in) 26.8800 Hub projection (in) 4.7800 Impeller eye to bottom of pit (in) 51.7500 Bell bottom to bottom of pit (in) 20.09 Strainer length (in) 0.0000 Strainer diameter (in) 0.0000 Discharge bowl length (in) 0.0000 Total bowl length (in) 77.66 Bowl shaft length (in) 91.2000

Weights

Bowl weight (lb) 5,080.0 0.0 Impeller weight (lb) 550.0 0.0

Bell weight (lb) 2,710.0 Strainer weight (lb) 0.0 Discharge bowl weight (lb) 0.0 Total bowl assembly weight (lb) 8,340.0

Characteristics-Bowl

K-factor @ shut-off 210.00 0.00 K-Factor @ design 210.00 0.00 K-Factor @ run-out 210.00 0.00 WR2 wet (Lbs Ft²) 939.00 0.00 Max.solid size (in) 5.8700 0.0000 Std bolting pressure limit (psi g) 150.0 √ 0.0 High-P bolting pressure limit (psi g) 200.0 √ 0.0 Lagged bowl pressure limit (psi g) 200.0 √ 0.0

Proposal No : TB16-01-11 02 Item No: Upriver Raw Water Pumps UP-1/UP-2/UP-3 Model: VIT May 4, 2016 (14:30:20 PM)

Characteristics-Shaft

Bowl shaft diameter (in) 4.0000 Bowl shaft material/Combined stress 416SS /18,000

Column - Dimensions and Characteristics Dimensions

Column nominal diameter (in) 36.00 √ Column length (in) 366.41 Bearing spacing 10ft Column pipe thickness (in) 0.3750 Column outside diameter (in) 36.0000 Column flange diameter (in) 43.0000 Taper column angle (deg) 8 Taper column length (in) 26.43 Enclosed Tube size (in) 6.0000 Enclosed tube thickness (in) 0.0000 Enclosed tube O.D. (in) 0.0000

Weight

Total Column weight (lb) 8,000.0 Characteristics-Column Rated Run-out

Column friction loss per 100 ft column 1.54 2.30 Total Column friction loss (ft) 0.47 0.70 Enlargement loss (ft) (bowl->column) 0.00 0.00 Column velocity (ft/sec) 12.76 15.58

Characteristics-Lineshaft

Lineshaft diameter (in) 3.6875 Discharge Head - Dimensions & Flow Properties

Discharge head size / material 36 / Duplex stainless steel Discharge flange rating 150 # RF ANSI Discharge Pipe OD (in) 36.0000 Discharge Thickness (in) 0.3750 Suction head size - Suction head flange rating - Discharge friction loss (RT/RO) (ft) 1.3 / 1.9 Velocity Head at discharge Nozzle (RT/RO) (ft) 2.327 / 3.468 Suction friction loss (RT/RO)-Can loss (RT/RO) (ft) - /0.0 Headshaft diameter / material 3.6875 in / 416SS Headshaft sleeve size (in) - Discharge head weight (lb) 4,400.0 √

Total Unit Weight (bowl-column-head-motor) 29740.0 lb

Proposal No : TB16-01-11 02 Item No: Upriver Raw Water Pumps UP-1/UP-2/UP-3 Model: VIT May 4, 2016 (14:30:20 PM)

Dimensions

Discharge Head C Dimension (in) 36.00 Discharge Head D Dimension (in) 38.00 Discharge Head ES/ET Dimension (in) 72.00 Discharge Head F Dimension (in) 2.75 Discharge Head G Dimension (in) 58.00 Discharge Head Actual Inside Diameter (in) 36.00 Distance from grade to bottom of motor stand (in) 50.000 Subbase W Dimension (in) Subbase X Dimension (in) Subbase Z Dimension (in) Subbase Y Dimension (in) 1.75 Discharge Head bolt circle (in) 54 Discharge Head J Dimension (in) 1.63

(C) Length of driver including shaft (in) (OD) Driver OD dimension (in) (AG) Driver height/length excluding shaft (in) 112.06 √ (AB) Shaft End to Rear of Rear Foot. (in)

NOTE: √ Indicates user-input values (or protected values) Program Version 1.57.0.0

Proposal No : TB16-01-11 02 Item No: Upriver Raw Water Pumps UP-1/UP-2/UP-3 Model: VIT May 4, 2016 (14:30:20 PM)

Goulds Pumps Vertical Products Operations Speed - Torque Curve

S.O. No. 315410-1-3 Customer : CDM CONSTRUCTORS INC.

P.O. No. : 110426.P.006 Proposal No : TB16-01-11 02 Item No. : Upriver Raw Water Pumps UP-1/UP-2/UP-3 VIT / 44GHC Speed : 710 RPM 100% Torque : 9,307.20 Feet*lb force at Shut off (closed valve) 100% Torque : 10,089.40 Feet*lb force at Run out (open valve) 100% Torque : 10,034.50 Feet*lb force at Rated Point WR2 of pump : 942.9 [Lbs Ft²]

Size: 44GHC Date: 05/04/2016 Rev. No: 0

P.O. NO: 110426.P.006

Product Number: 315411 Proposal No: TB16-01-11 02 Item No: Upriver Raw Water Pumps UP-4/UP-7

MODEL: VIT Size: 10 x 12JHC 4 STAGES QTY:2 Pump Design:ANSI/HI 2.3-2008 (Commercial Design Std.)

Operating Conditions SERVICE High Pressure Screen Backwash LIQUID Water (70.0 deg F) SP.GR 1.000 Viscosity 1.000 cp LIQUID TYPE Non Toxic CAPACITY 1,140.0 gpm RATED HEAD 205.0 ft SUMP DEPTH 38.68 (ft) (Pumping level 28.02 ft) NPSHa 43.4 ft at 1st imp.eye

Performance at 1780 RPM Shut-off Min. Flow Design

Flow(1) Run Out

Flow FLOW RATE (gpm) -0- 339.0 1140.0 1626.0 TDH (ft) 268.0 260.4 205.1 106.6

PUMP EFFY (%) -0- 42.7 75.5 57.0

POWER (hp) 38.7 52.2 78.1 76.7 NPSHr (ft) (2) 3.6 17.5 29.3 DOWN THRUST (Lb) 3452.6 2587.8 2094.8 1098.8 DISCH. PRESS. (psi g) (3) 103.5 76.2 MIN REQ.SUBMERG.(in) (4) 13.3 19.2 21.8

(1) Guaranteed Values

(2) First stage impeller eye elevation

(3) Pressure at Discharge centerline

(4) for vortex suppression, based on H.I. 1994 Edition

MAWP values Bowl - Std 132.8 psi g Column 132.8 psi g Disch.Head, Disch.Side 132.8 psi g Seal Hsg/Piping 132.8 psi g

Materials and Dimensions Bowl Assy BOWL ASTM A890 Grade 1B ACI Type CD4MCUN standard SUCTION BELL ASTM A890 Grade 1B ACI Type CD4MCUN IMPELLER ASTM A890 Grade 1B ACI Type CD4MCUN (Enclosed) keyed to the shaft, dynamically balanced to

8W/N BOWL SHAFT ASTM A582 Type 416 1.6875 (in) diameter

BOWL WEAR RINGS Type 420 HT CA-40 Stainless Steel (285-350 BHN) Set screwed IMPELLER WEAR RINGS Type 410 HT CA-15 Stainless Steel Set screwed

BOWL BOLTING ASTM A276 TP 316L

BOWL FEATURES

Grease return lines back to mounting plate, 316 Stainless Steel tubing Special design discharge bowl to relieve the injected grease Suction bearing housing plug material 316L Stainless Steel

Column Assy COLUMN ASTM A790 UNS S31803 / A240 UNS S31803 10.00 (in) diameter, 33.2 (ft) long Flanged

COLUMN BOLTING ASTM A479 UNS S31803

COLUMN SHAFT ASTM A582 Type 416, 1.1875 (in) diameter (enclosed) lineshaft sleeve: none ENCLOSING TUBE BRG Federal Alloy III (Modified), 3.3ft spacing ENCLOSING TUBE ASTM A790 UNS S31803, 2.0000 (in) diam., tube fluid: Grease LINESHAFT CPLG ASTM A276 Type 410 Cond T, Threaded TPL 38.51 (ft)

Head Assy DISCHARGE HEAD ASTM A790 UNS S31803 / A182 Gr F51 / A240 UNS S31803 w/Duplex Stainless Steel driver stand

HEAD BOLTING ASTM A479 UNS S31803

HEADSHAFT MATERIAL ASTM A582 Type 416, 1.1875 (in) HEADSHAFT CPLG ASTM A276 Type 316 Type A adjustable COUPLING GUARD 316L Stainless Steel DISCHARGE FLANGE 10 (in) 150# R.F.

HEAD FEATURES

ASTM A240 TP 316L Sole Plate Special Name plates

Sealing Method PACKING Acrylic yarn and graphite

TENSION PLATE ASTM A479 UNS S31803

Engineering Analysis Rotor Torsional Critical Frequency Analysis (complete pump & driver) (FEA) Structural Natural Frequency Analysis (complete pump & driver) (FEA) - for ESLA Internal Use Rotor Lateral Critical Frequency Analysis (complete pump & drive) (FEA)

Testing Assembled Pump Performance Test (Non-Witness) with…