Appendix D GAD315415 for DPs 5 and 8 - high pressure pumps.pdf

A

B

C

D

A

B

C

D

GOULDS PUMPS

R6.20 157,5[ ]

REF.

3.50 88,9[ ]

MIN.2.70

68,6[ ]

5.29 134,4[ ]

MIN.SUBMERGENCE

AT RATED FLOW

17.90 454,7[ ]

11.50 292,1[ ]

TOTAL

PUMP LENGTH

359.85 9140,2[ ]

10.75 273,1[ ]

GROUT

2.00 50,8[ ]

1.75 44,5[ ]

4.75 120,7[ ]

RECOMMENDED

DRILLED HOLE

DIAMETER IS

0.88 MIN.

1.31 MAX.

LTR ZONE REVISION BY DATE

A1 - ADDED

SW 07-12-16

A2 - REVISED

B1 - ADDED GREASE LINES

SW 12-08-16B2 - REVISED

B3 - ADDED

SW 03-09-17

C2 - ADDED

D - ADDED ANCHOR BOLT DETAIL SW 05-03-17

E1 - ADDED

SW 05-22-17

E2 - REVISED

F - REVISED SW 05-24-21

SHEET 1 OF 3

THIRD ANGLE

PROJECTION

FGAD315415

REVDRAWING

COPYRIGHT

APPROVED

CHECKED

S.W 03-02-16

DRAWN

HCL 03-02-16

DRAWING SCALE: NONE DIMENSIONS IN INCHES[MM]

PUMP OUTLINE DRAWING

MODEL VIT-FF

CUSTOMER: CDM CONSTRUCTORS INC.

GOULDS SERIAL NO.: 315415

PRODUCT NO: ----

CUSTOMER P.O. NO.: 110426.P.005

PUMP ITEM NO.: DOWN RIVER RAW WATER PUMPS DP-5 & DP-8

SERVICE: HIGH PRESSURE SCREEN BACKWASH PUMPS

CUSTOMER DATA

07-12-16DATE:S.WEBSTERSIGNATURE:

CERTIFIED FOR CONSTRUCTION ONLY WHEN SIGNED.

FOR PERFORMANCE INFORMATION REFER TO DATA SHEET

STAGES:3SIZE:8X13CMC

2PUMP QTY:MODEL: VIT-FF

FOR DRIVER INFORMATION SEE DRIVER PRINT

NIDECMFR.

DRIVER SPECIFICATIONS

TYPE: TENSION PLATEMFR: ITT

SHAFT SEAL

NOXYESGUARD PROVIDED:

ADJUSTABLETYPE:

ITTMFR:

COUPLING SPECIFICATIONS

V I T F F

T5

LIFTING LUG

-DETAIL-

A2

A2

A1

A2

A2

A2

PIT BOTTOM

A1SACRIFICIAL

ANODES ON

BOWL ASSEMBLY

C1

C1

C1

ANCHOR BOLT

-DETAIL-

SUPPLIED BY CUSTOMER

SOLE PLATE

(2) WASHER

HEX NUT

D

RECOMMENDED SOLUTION

SIMPSON AT-XP + 7/8 316 SS

PER ASTM F593 OR EQUIVALENT

4 PLACES

E1

E2

SQ.

22.00 558,8[ ]

OPENING

19.00 482,6[ ]

4 PLACES

1.00 25,4[ ]

TYP.

11.00 279,4[ ]

SEE

NOTE 3

32.25 819,2[ ]

36.00 914,4[ ]

SEE

NOTE 6

SEE

NOTE 7

15.50 393,7[ ]

1.75 44,5[ ]

9.50 241,3[ ]

SQ.

25.00 635,0[ ]

TYP.

12.50 317,5[ ]

3.50 88,9[ ]

2.50 63,5[ ] 2.40

61,0[ ]

0.50 12,7[ ]

0.50 12,7[ ]

R1.00 25,4[ ]

1.00 25,4[ ]

SOLE PLATE

-DETAIL-

DISCH.�q�

COUPLING GUARDS

(2) LIFTING LUGS

SEE NOTE 11

T4

T4

HEAD MOUNTING

FLANGE

T3

SEE NOTE 2 AND 5

PUMP ROTATION CCW

SEE SOLE PLATE

DETAIL

SEE DETAIL A

CONDUIT BOX

TOP VIEW

50�$�

C1 - REVISED

F

F

F F

F

F

F

F

F

F T8

PRESSURE

GAUGE

T7

T8

T1 F

T1

DRIVER SUPPORT

DRAIN LINE

1923.24240.0TOTAL

74.8165.0SOLEPLATE

430.9950.0DRIVER

14.532.0COUPLING

1403.03093.0PUMP

KGLBS ITEM

WEIGHTS(APPROXIMATE)

A

B

C

D

A

B

C

D

GOULDS PUMPS

SHEET 2 OF 3

THIRD ANGLE

PROJECTION

FGAD315415

REVDRAWING

COPYRIGHT

APPROVED

CHECKED

S.W 03-02-16

DRAWN

HCL 03-02-16

DRAWING SCALE: NONE DIMENSIONS IN INCHES[MM]

PUMP OUTLINE DRAWING

MODEL VIT-FF

CUSTOMER: CDM CONSTRUCTORS INC.

GOULDS SERIAL NO.: 315415

PRODUCT NO: ----

CUSTOMER P.O. NO.: 110426.P.005

PUMP ITEM NO.: DOWN RIVER RAW WATER PUMPS DP-5 & DP-8

SERVICE: HIGH PRESSURE SCREEN BACKWASH PUMPS

CUSTOMER DATA

C NO

ZZ

LE

Fz

Mz

S H A F T

FxFy My

Mx

L

COMMERCIAL (HI)

SINGLE NOZZLE LOADS

V I T F F

A2

10. FOR PUMPS OVER 200HP[149 KW] THE PUMP ASSEMBLY HAS BEEN

DESIGNED SO THAT ITS NATURAL FREQUENCY RESPONSES AVOID

THE SPECIFIED MOTOR SPEED (OR SPEEDS) BY AN ADEQUATE

SAFTEY MARGIN.THE DESIGN ASSUMES A RIGID FOUNDATION

11. ONLY USE LIFTING LUGS ON DISCHARGE HEAD TO LIFT THE PUMP

12. ON OFF SEASON PERIOD, CUSTOMER SHOULD OPEN VALVE AND INJECT

CLEAN WATER 1.5 - 2.5 GPMS FOR 3 MINUTES PRIOR TO

BUMP START AND CONTINUE FLUSH DURING THE BUMP START PROCESS.

13. ON OFF SEASON PERIOD, CUSTOMER SHOULD OPEN VALVE AND INJECT

CLEAN WATER 1.5 TO 2.5 GPMS FOR 3 MINUTES PRIOR TO

BUMP START AND CONTINUE FLUSH DURING THE BUMP START PROCESS.

14. VALVE TO BE OPEN 10%.

15. SET PRESSURE AT 35 PSI.

16. PERIODIC OBSERVATION AND CLEAN OUT OF FILTER IS REQUIRED.

17. RECOMMENDED BUMP TEST SPEED:

PUMP MINIMUM WET SPEED (HIGH WET WELL) IS 1424 RPM;

PUMP MAXIMUM WET SPEED (LOW WET WELL) IS 1780 RPM;

PUMP MAXIMUM DRY SPEED IS ZERO RPM. MULTI-STAGE UNITS

ARE TO BE ROTATED BY HAND ONLY(SEE NOTE 13).

CONNECTIONS TABLE

NO SIZE TYPE QTY PURPOSE STATUS FOR USE BY

T1 1/2" NPT 1 MOTOR SUPPORT DRAIN CONNECTED ITT

T2 1/2" NPT 1 TENSION PLATE (PLAN 32) INJECTION CONNECTED ITT

T3 8" 150# ASME RF SLIP ON FLANGE 1 PUMP DISCHARGE OPEN CUSTOMER

T4 1/2" NPT 1 PLAN 32 INJECTION CONNECTED ITT

T5 1/2" NPT 1 ALL AUXILIARY CONNECTIONS PLUGGED CUSTOMER

T6 3/8" NPT 2 AUXILIARY CONNECTION PLUGGED CUSTOMER

T7 1/2" NPT 1 OFF SEASON LUBE INJECTION VALVE CLOSED CUSTOMER

T8 1/2" NPT 1 FILTER RETURN CONNECTED ITT

T9 1/2" NPT 1 TENSION PLATE LUBE INJECTION CONNECTED ITT

T10 3/4" NPT 1 FILTER HOUSING DRAIN NOTE 14 ITT

5.25 133,4[ ]

FOUNDATION LOADS

NORMAL OPERATIONAL FOUNDATION LOAD IN VERTICAL

DIRECTION �x� = 5945 LBS [26457 N]

FLANGE

SIZE

Fx Fy Fz Mx My Mz

LBS. [NEWTON] FT-LBS.[NEWTON-METER]

8"

[3594]

[3238]

[3998]

[1686]

[2032]

[1458]

F

-DETAIL A-

WATER FLUSH

TENSION PLATE

ADJUSTABLE

COUPLING

T6 T6

FROM SPIN FILTER

SEE GAD SHEET 3 OF 3

T7

T2

T9

F

F

SEE NOTE 12

F

F

F

F

F

F

1. ALL PUMPS EQUIPMENT SUPPLIED MUST BE INSTALLED,PIPED

AND OPERATED IN ACCORDANCE WITH API 686 AND THE INSTRUCTION

MANUAL PROVIDED WITH EQUIPMENT

2. TOLERANCE ON ALL PUMP DIMENSIONS IS �#�.12[3,0] OR �#�.12[3,0]

PER 5 FEET[1,5 M] WHICHEVER IS GREATER.TOLERANCE ON ALL

PIPING DIMENSIONS IS AS FOLLOWS: DISCHARGE FLANGE IS

�#�.12[3,0] , AUXILIARY CONNECTIONS ARE �#�1.0[25,4]

3. OPENING DIAMETER TO CLEAR PUMP,DRAIN AND COLUMN ASSEMBLY

IS 18.00 [457,2] MIN/19.00 [482,6] MAX

4. BEFORE INITIAL PUMP START UP, THE ROTOR MUST BE LIFTED

0.187[4,74].TO LIFT ROTOR USE ADJUSTING PLATE ON THE

ADJUSTABLE COUPLING.

5. M.A.W.P. DISCHARGE = 136.1 PSIG [9.38 BARG] @ 70�$�F [21.1�$�C]

6. MINIMUM HEIGHT REQUIRED TO REMOVE DRIVER IS 10.00 [254,0].

LIFT DRIVER SEPARATELY.DIMENSION DOES NOT INCLUDE THE

REQUIRED RIGGING DISTANCE BETWEEN THE TOP OF DRIVER

TO THE HOOK.

7. MINIMUM HEIGHT REQUIRED TO REMOVE ASSEMBLED PUMP

(LESS MOTOR) IS 408.0 [10363,2].DIMENSION DOES NOT INCLUDE

THE REQUIRED RIGGING DISTANCE BETWEEN THETOP OF

PUMP TO THE HOOK.

8. BOLT HOLES ON ALL FLANGES STRADDLE VERTICAL CENTERLINE

9. PRIOR TO PUMP INSTALLATION, SOLE PLATE SHALL BE

MOUNTED SEPARATELY ON FOUNDATION/STRUCTURE SUPPORTS.

SOLE PLATE SHALL BE LEVELED TO .002 INCHES PER FOOT

[,050 MM PER 304,8 MM] SECURED IN PLACE,AND EPOXY

GROUT SHALL BE FILLED BETWEEN FOUNDATION SUPPORTS

AND THE UNDERSIDE AND SIDES OF THE SOLE PLATE.AFTER

GROUT SETS,THE ANCHOR BOLTS SHALL BE FULLY TIGHTENED.

NOTES

A

B

C

D

A

B

C

D

GOULDS PUMPS

SHEET 3 OF 3

THIRD ANGLE

PROJECTION

FGAD315415

REVDRAWING

COPYRIGHT

APPROVED

CHECKED

S.W 03-02-16

DRAWN

HCL 03-02-16

DRAWING SCALE: NONE DIMENSIONS IN INCHES[MM]

PUMP OUTLINE DRAWING

MODEL VIT-FF

CUSTOMER: CDM CONSTRUCTORS INC.

GOULDS SERIAL NO.: 315415

PRODUCT NO: ----

CUSTOMER P.O. NO.: 110426.P.005

PUMP ITEM NO.: DOWN RIVER RAW WATER PUMPS DP-5 & DP-8

SERVICE: HIGH PRESSURE SCREEN BACKWASH PUMPS

CUSTOMER DATA

T4

DISCHARGE

NOZZLE

MODIFIED PLAN 32 AND

OFF SEASON LUBRICATION

SCHEMATIC

T6T6

1/2" X 1" NPT ADAPTER

F

1" TUBING

T8

3/4" X 1/2"

REDUCING ADAPTER

HEAD MOUNTING

PLATE

T7

PRESSURE GAUGE

PRESSURE SWITCH

(SEE NOTE 15)

1/2" MALE X 1/4" FEMALE REDUCER

SIGHT FLOW

INDICATOR

T9T2

TEE 1/2"

TENSION

PLATE

SPIN CLEAR FILTER

(SEE NOTE 16)

1-1/2" TO 1"

REDUCING COUPLING

1" TUBING

1" NPT X 1"

TUBE CONNECTOR

1/2" PIPE NIPPLE

1/2" X 1" NPT ADAPTER

3/4" FLEXIBLE HOSE

WITH NPT ENDS

1/2"NPT X 1/2"

MALE TUBE

CONNECTOR

T10 (NOTE 14)

1" NPT X 1"

TUBE CONNECTOR