Attachment 22a.1.c - ALH-211130 00 CABLE ASSEMBLY CASS DC POWER.pdf

2012/08/06

W31P4Q-08-C-0148

DATEAPPROVALS

PROJECT APPROVAL

DESIGN ACTIVITY

CCB CHAIR

T. ALKIRE

J. WETHINGTON

ENGR

K. HANVEY

J. BULLEIGH

CONTRACT NO.

1 OF 3 SHEETNONE SCALE

NG-IPS-ALH8-AC-D00 (IBCS)

CAGE CODESIZE DWG NO. REV.

WARNING - This document contains technical data whose export

Official version of this document is electronically controlled in an online PLM system. Verify version level prior to use.

NOTES:

1. APPLICABLE STANDARDS/SPECIFICATIONS:

ASME Y14.5M - 1994, DIMENSIONING AND TOLERANCING

2. WORKMANSHIP SHALL MEET OR EXCEED IPC/WHMA-A-620 CLASS 3.

3. SEE ALH-900000 FOR ENGINEERING APPROVED EQUIVALENTS FOR

NON-DEVELOPMENTAL OFF THE SHELF PARTS.

4 BAND MARKINGS:

4.1 BAND MARKINGS SHALL BE SINGLE THERMAL MARKING EMPLOYING

A PERMANENT BLACK MATERIAL. CHARACTERS SHALL BE

VERTICAL GOTHIC TYPE. HEIGHT SHALL BE PROPORTIONAL AND

LEGIBLE.

4.2 BAND SHALL EXTEND PROPORTIONALLY BEYOND LETTERING ON

FRONT AND REAR OF MARKINGS.

5 ENTER MANUFACTURER'S CAGE CODE IN PLACE OF "_ _ _ _ _" IAW

MIL-STD-130.

6 CABLE LENGTHS DETERMINED BY 4-DIGIT DASH NUMBER (i.e.

ALH-123456-0120 IS 120 INCHES).

CABLE TOLERANCE: THE LENGTH OF A CABLE SHALL BE MEASURED

FROM ONE END OF THE CABLE ASSEMBLY TO THE OTHER END

(REFERENCE CABLE ASSEMBLY DIAGRAM). CABLE LENGTH TOLERANCE

SHALL BE AS SHOWN IN THE CABLE LENGTH TOLERANCE TABLE

UNLESS OTHERWISE DEFINED ON THE DRAWING/DOCUMENTATION.

7. CABLES SHALL BE TESTED BY REQUIREMENT TS-1C IDENTIFIED IN

ALH-102546.

8 BAND MARKING ORIENTATION: FOR CABLES LESS THAN OR EQUAL TO

18 INCHES, ONLY ONE CENTER BAND MARKING LABEL "A" IS REQUIRED

ON THE CABLE CENTERED ±.5 INCHES ON THE EXPOSED CABLE

BETWEEN CONNECTORS OR TERMINALS. MARKING LABELS "B" AND "C"

ARE TO BE LOCATED 1" ±.5" FROM BACKSHELL/TERMINAL IN PLACE OF

DIMENSION SHOWN.

9 REPLACE: MM-YYYY WITH MONTH AND YEAR OF MANUFACTURE;

XX WITH DRAWING REVISION USED FOR MANUFACTURE.

10. CABLE PREPARATION, CRIMP TOOL/DIE, AND CONNECTOR/WIRE

ASSEMBLY SHALL BE AS SPECIFIED IN THE INDIVIDUAL CONNECTOR

SPECIFICATIONS OR AS REQUIRED TO MEET THE OVERALL CABLE

ASSEMBLY REQUIREMENTS.

11 FOR ADEQUATE STRAIN RELIEF, THIS AREA MAY REQUIRE ONE OR

MORE LAYER(S) OF FN 2.

WARNING - This document contains technical data whose export

Copyright 2012 Northrop Grumman Systems Corporation

DISTRIBUTION STATEMENT C: Distribution authorized to the U.S. Government Agencies and their contractors; Administrative and Operational Use; 05 Jan 2007. Other requests for this document shall be referred to ATTN: SFAE-MSLS-IAMD, Program Executive Office Missiles and Space, Integrated Air and Missile Defense Project Office. Bldg. 5250 Martin Road, Huntsville, Al 35898-8000.

is restricted by the Arms Export Control Act (Title 22, U.S.C., Sec 2751, et. seq.) or the Export Administration Act of 1979, as amended, Title 50, U.S.C., App. 2401 et. seq. Violations of these export laws are subject to severe criminal penalties. Disseminate in accordance with provisions of DoD Directive 5230.25.

2012/08/06

REV.DWG NO.SIZE CAGE CODE

NGMS-ALH8-AC-D04

SCALE NONE SHEET 2 OF 3

Official version of this document is electronically controlled in an online PLM system. Verify version level prior to use.

VIEW A-A

KEYWAY

A D C

B

A A

CABLE ASSEMBLY

A

TABLE

MARKING DESCRIPTION

318U8 ASSY ALH-211130-XXXX

MM-YYYY REV XX MFR _ _ _ _ _

CASS DC POWER CABLE

A

28 V DC

PWR SOURCE

B

SEE TABLE

FOR MARKINGS4X

C

AB

28 V DC

J4

C

2X 2.0±.52X 1.0±.5

2 2X

LENGTH SHALL BE AS REQUIRED

FOR CABLE ASSEMBLY

REV.DWG NO.SIZE CAGE CODE

NGMS-ALH8-AC-D04

SCALE NONE SHEET 3 OF 3

Official version of this document is electronically controlled in an online PLM system. Verify version level prior to use.

WIRING DIAGRAM

REF

REF

5C

A

B

D

RED (+28 VDC)

BLACK (-28 VDC RTN)

B

C

A

D

WHITE

TRIM CONDUCTOR

FLUSH WITH END

OF CABLE

2X