A04_0040564583_Attch_0003_Phase_I_and_II_Product_Specs_MALU_Exterior_Lighting_Improvements.pdf

ATTENTION:

READ BEFORE REMOVING FIXTURE FROM CARTON.

Tools Required: Allen Key (3/16"), Phillips screw driver, electrical wiring tools.

NOTE: This lighting fixture should not be used in area of limited ventilation or in high ambient temperature enclosures. It must be stored in a dry location prior to installation. Do not expose lighting fixture to rain, dust or other environmental conditions prior to installation.

Best results will be obtained if installed and maintained according to the following recommendations.

NOTE: Care must be taken not to set lighting fixture down on optical lenses or lift the fixture in the lens area.

APPLICATIONS

• Minimum 90ºC Supply Conductors when connections are made external to the unit.

• Rated for 40ºC (104ºF) ambient.

• Suitable for wet location.

• Wall mount luminaire only.

• Construction is suitable for down mount only.

• Must be mounted above grade at minimum 4 feet or higher.

• Suitable for mounting on combustible construction grade wall surfaces.

INSTALLATION

Standard Down Mount Application— FIG. 1 and FIG. 1a

1 Remove the mounting plate from the fixture by loosening the two socket head cap screws using 3/16" allen key.

2 Loosen the lock nut from the mounting plate.

3 Detach tether from the mounting plate.

4 Mount the mounting plate to the junction box or wall with gasket contacting wall, away from the luminaire and secure to the structure with screws (by others).

These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible contingency during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please contact your nearest representative.

ENTRI LED

Sheet 1 of 4

1/6/10 IMI-722INSTALLATION INSTRUCTIONS

IMPORTANT: READ CAREFULLY BEFORE INSTALLING FIXTURE.

UN

WARNING: Risk of Fire/Electric Shock. If not qualified, consult an electrician.

WARNING: Risk of Electric Shock. Disconnect power at fuse or circuit breaker before installing or servicing.

WARNING: Risk of Burn. Disconnect power and allow fixture to cool before servicing.

WARNING: Risk of Personal Injury. Fixture may become damaged and/or unstable if not installed properly.

NOTE: Specifications and dimensions subject to change without notice.

Visit our web site at www.cooperlighting.com Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX 770.486.4801 AVU091925

FIG. 1

Door Latch

Fixture

Mounting Bracket

Tether

Lock Nut (2)

J-Box or Wall

Gasket on Back

Allen Head Screws (2)

Mounting Plate (Secure to J-Box or Wall)

Plug (Make sure this is in place before securing fixture to wall)

FIG. 1a

Mounting plate must be in upright position as specified by label.

NOTE: Care must be taken not to set lighting fixture down on optical lenses or lift the fixture in the lens area.

5 Make sure plug at bottom of housing is in place properly as shown in FIG. 1a.

6 Make electrical connections.

7 Re-attach tether to mounting plate.

8 Tighten the lock nut.

NOTE: Tether must be able to rotate freely; therefore, do not over tighten lock nut. Fixture must hang from the tether, NOT from electrical wires.

9 Slide the luminaire-mounting bracket over the top lid of the mounting plate to nest the hanging mechanism.

Hold luminaire in place while allowing the back surface of luminaire to rest against wall.

10 Screws must be captured behind lower beveled edge of mounting plate to ensure luminaire is secure. Press luminaire firmly against wall and re-tighten the two (2) socket head cap screws to secure the luminaire to the mounting plate.

THRUWAY BOX-VA2001-XX ACCESSORIES

FIG. 2, 2a, and 2b, for use in down mount application only.

NOTE: Unit with a thruway box weighs more than 25 pounds. Therefore, connect mounting plate to the wall using the 4 larger holes and appropriate anchors/hardware (not provided).

1 Remove the mounting plate from the back of thruway box by loosening two (2) Allen head screws.

2 Mount the mounting plate to the wall using the four (4) larger holes with required hardware (by others). Plate must be in the correct upright position.

These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible contingency during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please contact your nearest representative.

ENTRI LED

Sheet 2 of 4

1/6/10 IMI-722INSTALLATION INSTRUCTIONS

IMPORTANT: READ CAREFULLY BEFORE INSTALLING FIXTURE.

UN

NOTE: Specifications and dimensions subject to change without notice.

Visit our web site at www.cooperlighting.com Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX 770.486.4801 AVU091925

FIG. 2

Gasket

Thruway Box Housing Allen Head

Screws (2)

(4) Larger Holes

Mounting Screws

Gasket on Back

Mounting Plate (Secure to Wall)

Donut Gasket (on Back Box)

Wireway Plug Mounting Bracket

Thurway Box Cover

FIG. 2a

Allen Head Screw

Gasket on Back

10-24 x 5/8" SST Screw 10-24 x 5/8"

SST Screw

Thruway Box Cover

Thruway Box Housing

Thruway Box Gasket

Tether

Hex Washer Nut

Nylon Lock Nut

Mounting Plate (Remove from back of fixture)

Tether’s Connection (Connect to the back of fixture)

WARNING: Risk of Fire/Electric Shock. If not qualified, consult an electrician.

WARNING: Risk of Electric Shock. Disconnect power at fuse or circuit breaker before installing or servicing.

WARNING: Risk of Burn. Disconnect power and allow fixture to cool before servicing.

WARNING: Risk of Personal Injury. Fixture may become damaged and/or unstable if not installed properly.

3 Slide the thruway box mounting bracket over the lid of the mounting plate.

4 Re-tighten the two (2) Allen head screws to secure the thruway box to the mounting plate.

5 If used with thru branch wiring, then remove plugs on side as required and install 3/4" NPS pipe. Seal pipe with Teflon tape or paste.

6 Remove the thruway box cover from the thruway box housing by loosening five (5) screws.

7 Remove mounting plate from the back of the fixture by loosening two (2) Allen head screws.

8 Install the fixture-mounting plate on thruway box cover with four (4) screw and nuts provided.

9 Pull supply wires through center hole and re-install thruway box cover back on thruway box housing.

NOTE: Make sure wire plug stays in place.

10 Attach the tether from the back of fixture to the mounting plate.

11 Tighten the lock nut.

NOTE: Tether must be able to rotate freely; therefore, do not over tighten lock nut.

12 Slide the luminaire-mounting bracket over the top lid of the mounting plate

13 Tighten the two (2) Allen screws to secure the luminaire to the mounting plate.

THRUWAY BOX WITH OPTIONS

FIG 3 and 3a, for use in down mount application only

1 Repeat step 1 through 6 in “Thruway Box—VA2001-XX Accessories.”

2 Remove the thruway box cover from thruway box housing by loosening five (5) screws.

3 Remove the thruway box door by loosening four (4) screws.

4 Pull supply wires and re-install thruway box cover back on thruway box housing.

These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible contingency during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please contact your nearest representative.

ENTRI LED

Sheet 3 of 4

1/6/10 IMI-722INSTALLATION INSTRUCTIONS

IMPORTANT: READ CAREFULLY BEFORE INSTALLING FIXTURE.

UN

NOTE: Specifications and dimensions subject to change without notice.

Visit our web site at www.cooperlighting.com Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX 770.486.4801 AVU091925

Fixture

Mounting Plate

Thruway Box

FIG. 2b

Mounting Plate (secure to wall)

Mounting Plate

Quick Disconnect

FIG. 3

WARNING: Risk of Fire/Electric Shock. If not qualified, consult an electrician.

WARNING: Risk of Electric Shock. Disconnect power at fuse or circuit breaker before installing or servicing.

WARNING: Risk of Personal Injury. Fixture may become damaged and/or unstable if not installed properly.

NOTE: Make sure wire plug stays in place.

5 Attach the tether from the back of fixture to the mounting plate.

6 Tighten the lock nut.

NOTE: Tether must be able to rotate freely; therefore do not over tighten lock nut.

7 Plug the quick-disconnect.

8 Push the wires into the thruway box.

9 Slide the luminaire-mounting bracket over the top lid of the mounting lid.

10 Tighten the two (2) Allen head screws to secure the luminaire to the mounting plate.

11 Re-install the thruway box door.

WIRE GUARD INSTALLATION (OPTIONAL)

FIG. 4, for use in down mount application only.

1 Unscrew four (4) Philip screw from the bottom of the housing.

2 Align the four (4) holes in clips of wire guard with holes in the bottom of housing.

3 Secure wire guard to luminaire with four (4) provided screws.

MAINTENANCE:

NOTE: A regular maintenance schedule should be followed to retain optimal light output and thermal performance.

Optical lens cleaning should be performed with a clean dry soft cloth to remove any dust or other contaminants.

Additional cleaning can be performed with non-abrasive acrylic cleanser.

NOTE: DO NOT USE GLASS CLEANERS.

These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible contingency during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please contact your nearest representative.

ENTRI LED

Sheet 4 of 4

1/6/10 IMI-722INSTALLATION INSTRUCTIONS

IMPORTANT: READ CAREFULLY BEFORE INSTALLING FIXTURE.

UN

NOTE: Specifications and dimensions subject to change without notice.

Visit our web site at www.cooperlighting.com Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX 770.486.4801 AVU091925

Quick Disconnect

FIG. 3a

WARNING: Risk of Fire/Electric Shock. If not qualified, consult an electrician.

WARNING: Risk of Electric Shock. Disconnect power at fuse or circuit breaker before installing or servicing.

WARNING: Risk of Burn. Disconnect power and allow fixture to cool before servicing.

WARNING: Risk of Personal Injury. Fixture may become damaged and/or unstable if not installed properly.

Housing

Wire Guard

Screw (Secure to Housing)

FIG. 4

Installation and Technical InformationBEGA

In the interest of product improvement, BEGA reserves the right to make technical changes without notice.

Replacement PartsAccessories Please refer to the appropriate accessory installation sheet for further instruction when applicable.

BEGA 1000 Bega Way, Carpinteria, CA 93013 (805)684-0533 Fax (805)566-9474 www.bega-us.com © Copyright BEGA-US 2018

Figure 2: Secondary Wall Mount Screw Holes

Figure 1 (Generic Image)

LED ceiling and wall luminaires 33 509 Tools Required:

2.5mm hex key 3mm hex key Phillips head screwdriver medium Flat head screwdriver

Protection class: IP65

Weight: 7.7 lbs.

Dimensions A: 10-1/4 ”

B: 4-3/4 ”

Relamping/Maintenance No relamping required.

Lamp: 10.5W LED

33 509 7/26/2018

Description

Lens Gasket

Driver LED Module (3000K) LED Module (4000K)

Part No

11297611 831382

75983-01

LED-0381/930

LED-0381/940

Notice to Installer for 33 509:

1. BEGA luminaires may be damaged if connected to conduit systems containing water- Article 300-5G of National Electric Code requires that “Conduits or raceways through which moisture may contact energized live parts shall be sealed or plugged at either or both ends”.

2. Mounts directly to a standard octagonal 4” wiring box (by others) using BEGA mounting kit (supplied).

NOTE: Recommended that installer uses (2) screws (by others) to lock in place back housing, along with BEGA mounting kit, to wall surface for eased installation. (Fig. 2)

3. In conformance with U.L. Standards 1598, a silicone-based sealant MUST be used between the mounting plate edge and supporting wall.

4. LEDs are high-quality electronic components! Please avoid touching the light output opening of the LED directly during installation.

33 509 - Installation:

1. Loosen 3mm set screw on luminaire outer trim ring and turn ring to the stop (ccw).

Remove trim ring with glass from luminaire base.

2. Loosen (2) hex screws on LED module plate and CAREFULLY remove LED module -trying not to come into direct contact with the LED chips.

3. Install (2) long 8-32 x 3/4” mounting screws (provided) in the back of the adapter plate as shown (Figure 1).

4. Attach adapter plate to wiring box using (2) 8-32 x 1/2” screws provided. Feed luminaire wires through luminaire base and adapter plate.

5. Make supply wiring and luminaire wiring connections in the octagonal wiring box:

MAIN VOLTAGE SUPPLY WIRE TO BLACK LUMINAIRE WIRE

NEUTRAL (COMMON) SUPPLY WIRE TO WHITE LUMINAIRE

WIRE GREEN GROUND WIRE TO GREEN LUMINAIRE WIRE

Dimming (if applicable):

DIMMING CONTROL WIRE (+) TO POSITIVE DRIVER DIM CONTROL WIRE

DIMMING CONTROL WIRE (-) TO NEGATIVE DRIVER DIM CONTROL WIRE

6. Place a small bead of silicone around the back side of the luminaire base that will come in contact with the finished wall (exterior applications only).

7. Attach luminaire to adaptor plate over the mounting screws using the (2) acorn nuts provided in the mounting kit. Tighten the nuts to back the screws into the wiring box and secure the plate to the box.

8. Replace the LED module carefully along with luminaire lens and trim ring. Turn trim ring to the stop (cw) and tighten outer set screw to secure.

CSA certified to U.S. and Canadian standards.

Suitable for wet locations.

In the interest of product improvement, BEGA reserves the right to make technical changes without notice.

BEGA 1000 Bega Way, Carpinteria, CA 93013 (805)684-0533 Fax (805)566-9474 www.bega-us.com © Copyright BEGA-US 2018

LED ceiling and wall luminaires 33 509

33 509 7/26/2018

Product Safety Warnings:

THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.

SUITABLE FOR WET LOCATIONS.

MIN 90°C SUPPLY CONDUCTORS.

CE PRODUIT DOIT ÊTRE INSTALLÉ SELON LE CODE D’INSTALLATION PERTINENT, PAR UNE PERSONNE QUI CONNAÎT

BIEN LE PRODUIT ET SON FONCTIONNEMENT AINSI QUE LES RISQUES INHÉRENTS.

CONVIENT AUX EMPLACEMENTS MOUILLÉS.

LES FILS D’ALIMENTATION 90°C MIN.

PRODUCT SPECIFICATIONSPRODUCT SPECIFICATIONS

LED ENGINE

Light engine shall include an array of 30 solid state Cree X- Series high power LEDs (light emitting diodes). The emitters shall be mounted to a metal core circuit board using SMT tech-nology. The LEDs and circuit boards shall then be mounted to a high performance heat sink which is vented to the outside ambient air to provide dynamic airflow for cooling the system.

OPTICS

External light control shall consist of high precision refractive lenses mounted above the LED emitter arrays in such a way to achieve optimum uplight control. The lenses shall also control horizon-tal light distribution so that Type II, III, IV or V IESNA distribution patterns are achieved.

LENS

The K729 Aurora Jr. pendant is available with or without a lens. Lens options include; sag glass lens; shallow glass lens;

rippled acrylic shallow lens; or rippled acrylic deep dish lens.

The glass lens shall be made of #9000 clear borosilicate glass (fully annealed). It shall maintain a minimum thickness of 0.16”.

The acrylic lens shall be moulded of rippled acrylic Acrylite Plus Acrylic Polymer, or equivalent, having a minimum thickness of 0.15”. The lens is secured by means of a cast A319 aluminum holding ring that is sealed to pro-vide an IP66 Ingress rating. Ad-ditionally, a continuous circular gasket rated for 270°F must hold the lens into place within the cast ring assembly and assist in seal-ing the fixture.

CAST HOUSING

The luminaire shall consist of a heavy Grade A319 cast aluminum housing that acts as the enclo-sure for the engine and is of ade-quate thickness to give structural rigidity. The engine must be af-fixed to the inside of the housing with stainless steel screws.

PLUMBIZER

The K729 Aurora Jr. comes with multiple mounting options in-cluding the KPL10, KPL11, KPL20, KPL21, KPL30, KPL31 and KPL40.

Please contact King Luminaire for more details and specifications.

DRIVER

The LED universal dimmable driver will be class 2 and capable of 120 - 277V or 347 - 480V input voltage, greater than 0.9 power factor, less than 20% total har-monic distortion. The case tem-perature of the driver can range from -40°C up to 70°C. Each LED system comes with a stan-dard surge protection designed to withstand up to 20kV/10kA of transient line surge as per IEEE C62.41.2 C High. An in-line ferrite choke is utilized to provide pro-tection against EFT’s. The driver assembly will be mounted on a fabricated aluminum bracket to allow complete tool-less mainte-nance.

PHOTOMETRICS

Fixtures are tested to IESNA LM79 specifications. These re-ports are available upon request.

CHROMATICITY

High output LEDs come standard at 3000K & 4000K (+/- 300K) with a minimum nominal 70 CRI.

Additional CCT emitters are available upon request.

LUMEN MAINTENANCE

Reported (TM21) and Calculated (L70) reports are available upon request with a minimum calcu-lated value of 100,000 hrs.

WIRING

All internal wiring and connec-tions shall be completed so that it will be necessary only to attach the incoming supply connectors to Mate-N-Lok connectors or to a terminal block. Mate-N-Lok shall be certified for 600V operation.

Internal wire connectors shall be crimp connector only and rated at 1000V and 150°C. All wiring to be CSA certified and/or UL listed, type SFF-2, SEWF-2, or SEW-2 No. 14 gauge, 150°C, 600V, and color coded for the required volt-age.

THERMALS

Fixtures tested to DOE sanc-tioned standards to determine the maximum in-situ solder-point or junction-point temperatures of the LED emitters. This report is available upon request.

FINISH

Housing is finished with a 13 step KingCoat™ SuperDurable poly-ester TGIC powder coat. Stan-dard colors include strobe white, brown metal, marina blue, gate gray, Chicago bronze, standard gold, standard black, federal green and rain forest. Please see our website for a complete list of colors. RAL and custom color matches are available.

MISCELLANEOUS

All exterior hardware and fas-teners, wholly or partly exposed, shall be stainless steel alloy. All internal fasteners are stainless steel or zinc coated steel. All remaining internal hardware is stainless steel, aluminum alloy, or zinc coated steel.

WARRANTY

The K729 Aurora Jr. LED lumi-naire comes with a 7 year limited warranty.

CERTIFICATION:

CSA US Listed Suitable for wet locations

ISO 9001

IP66

ARRA Compliant LM79 / LM80 Compliant

DRIVER INFO:

>0.9 Power Factor <20% Total Harmonic Distortion 120 - 277V & 347 - 480V -40°C Min. Case Temperature 70°C Max. Case Temperature Surge Protection: ANSI C136.2 extreme level 20kV/10kA

EPA:

Flat: 0.63 sq. ft.

Sag Lens: 0.66 sq. ft.

Shallow Lens: 0.74 sq. ft.

Deep Dish Lens: 0.84 sq. ft.

FIXTURE WEIGHT:

Flat: 19 lbs Sag Lens: 22 lbs Shallow Lens: 23 lbs Deep Dish Lens: 23 lbs

17 5/8" 20 3/4" 23 1/2" 28 1/8"

K729K729 AURORA JR. - LEDAURORA JR. - LED

A 3/4 scaled version of the K829, the K729 Aurora Jr. provides a gently curved fixture designed to be used on its own in a street or area lighting system, or in combination with its matching K800 luminaire.

This allows both roadway and pedestrian concerns to be individually met without any compromise.

Not all product variations listed on this page are DLC qualified.

Visit www.designlights.org/search to confirm qualification.

1-30-2020

K729

LUMINAIRE STYLE

K7 29 - Aurora Jr.

OPTICAL OPTIONS

P4FL - P4 Flat (no lens) P4SA - P4 Sag Glass Lens P4SH - P4 Shallow Glass Lens P4RAS - P4 Shallow Acrylic Lens P4RAD - P4 Deep Dish Acrylic Lens

IES LIGHTING

CLASSIFICATION

II - Type 2

III - Type 3 IV - Type 4 V - Type 5 SOURCE

SSL - Solid State

7030 (30 emitters)

SERIES

WATTAGE

40, 60, 75, 100

- - - (SSL) 7030

120V (120-277V) 480V (347-480V)*

*Select wattages available within this range, contact King Luminaire

LINE VOLTAGE

KPL10, KPL11, KPL20,

KPL21, KPL30, KPL31,

KPL40

*leave blank if not required

PLUMBIZER

PHOTO CONTROL OPTIONS

PR - Photo Receptacle, available with

KPL11, KPL20, KPL21, KPL30, KPL31

PE - Photo Receptacle and Photo Eye.

Available with KPL11, KPL20, KPL21, KPL30, KPL31

PEBC - Photo Electric Buttoncell

* leave blank if not required

PAINT COLOR

GN - Federal Green BE - Blue

GY - Gray BN - Brown BK - Black BZ - Bronze

*Additional options available on website

WATTAGE

SELECTOR

WS - Wattage Selector

* leave blank if not required

CCT

3K - 3000K 4K - 4000K

HOW TO ORDERHOW TO ORDER

K729 AURORA JR. - LED

17 5/8" 20 3/4" 23 1/2" 28 1/8"

FIXTURE OPTIONSFIXTURE OPTIONS

Lens Options

Sag Shallow Deep Dish

Plumbizer/Mounting Options

Flat (no lens) www.scgrp.com

1 3/4”

5 5/8”

7 5/8”

6 1/2”

7 3/8” 10” 7 3/4”

KPL10 KPL11* KPL20** KPL21**

KPL31** KPL40KPL30**

*Available with PR7 **Available with PR7 or finial

OVERVIEW • SPECIFICATIONS • ORDERING INTERIOR + EXTERIOR | F080 DUO

DATE P ROJ EC T FI R M T Y PE

RISE™

1/4ECOS E N S E LIG HTING .COM

20191216

P • 310.496 . 6255 F • 310.496 . 6256 T • 855.632.6736

855.6 . ECOSEN

ECOSENSE LIGHTING INC.

837 NORTH SPRING STREET

SUITE 103

LOS ANGELES, CA 90012

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.

VISIT ECOSENSELIGHTING.COM FOR THE MOST CURRENT SPECIFICATIONS.

FOR A LIST OF PATENTS VISIT ECOSENSELIGHTING.COM/IP-PORTFOLIO/

©2019 ECOSENSE LIGHTING INC. ALL RIGHTS RESERVED. ECOSENSE, THE

ECOSENSE LOGO, TRoV, TROV AND ECOSPEC ARE REGISTERED TRADEMARKS

OF ECOSENSE LIGHTING INC.

RISE™, SLIM COVE™, FREEDOM TO CREATE™, MACRO™, FLIP-TO-FLAT™ ARE

TRADEMARKS OF ECOSENSE LIGHTING INC.

RISE IS A SYSTEM OF BEAUTIFULLY DESIGNED OUTDOOR RATED LUMINAIRES THAT

PROVIDE EFFICIENT AND POWERFUL LIGHT USING THE LATEST IN LED TECHNOLOGY.

RISE F080 DUO IS A UNIQUE CONFIGURATION THAT PAIRS UP TWO RISE F080 SINGLES

ALLOWING YOU TO DOUBLE YOUR LUMEN POWER, DELIVERING UP TO 2340 LUMENS.

THIS UNIQUE FIXTURE CAN BE USED TO POWERFULLY LIGHT ONE OBJECT OR AIMED

SEPARATELY, ALLOWING YOU TO ILLUMINATE MULTIPLE APPLICATIONS. THIS

POWERFUL AND COMPACT LED LIGHT FIXTURE CAN BE USED IN SPOT, ACCENT,

LANDSCAPE AND FLOODLIGHT APPLICATIONS. ITS UNIQUE MACRO™ LOCK FEATURE

ALLOWS FOR FULL 180 DEGREE TILT AND 360 DEGREE PAN AIMABILITY OF EACH

FIXTURE HEAD USING ONLY ONE TWIST.

FEATURES:

• POWERFUL CBCP

• EXTREMELY COMPACT

• POWERFUL OUTPUT UP TO 2340 LUMENS

• MACRO™ LOCK - 180° TILT AND 360° PAN

• 12 UNIQUE BEAM ANGLES

• MULTIVOLT (110V-277V)

• 8 CCTS: 2200K THROUGH 6500K

• 80+ AND 90+ CRI

• DIMMABLE TO 5%

• IP66 RATED

ACCESSORIESBEAM ANGLECRI CCT/

COLOR

POWER/

LUMEN

OUTPUT*

FIXTURE

CONFIG.

FIXTURE

MODEL

FINISHES WIRING AND

MOUNTING

05 - Laser Spot (5°) 10 - Very Narrow Spot (10°) 15 - Narrow Spot (15°) 20 - Spot (20°) 40 - Flood (40°) 60 - Medium Flood (60°) 70 - Wide Flood (70°) 90 - Very Wide Flood (90°) E1 - Elliptical 1 (15°x60°) E2 - Elliptical 2 (30°x60°) E3 - Elliptical 3 (60°x15°) E4 - Elliptical 4 (60°x30°)

22 - 2200K 25 - 2500K 27 - 2700K 30 - 3000K 35 - 3500K 40 - 4000K 50 - 5000K 65 - 6500K RD - Red GR - Green BL - Blue AM - Amber

*2200K and 2500K not available in 40°, 60°, 70° and 90°

K - Black Z - Bronze S - Silver W - White C - Custom*

*Provide RAL #

X - No Accessory H - Half Snoot F - Full Snoot

Will ship as X if not specified

B - 10’ External Cable

Side Exit; Surface Mount;

UL Listed

C* - 10’ External Cable

Bottom Exit; Surface

Mount - 1/2” NPT; UL Listed

D* - 10’ External Cable

Side Exit; Surface Mount;

CE Listed

E* - 10’ External Cable

Bottom Exit; Surface

Mount - 1/2” NPT; CE Listed

*Will Ship as C if not specified

F080 2V - 2 Heads, Vertical Orientation

2H - 2 Heads, Horizontal Orientation

* ENERGY STAR REPORTED TESTING HOURS TO DATE.

CALCULATIONS FOR LED FIXTURES ARE BASED ON

MEASUREMENTS THAT COMPLY WITH IES LM-80

TESTING PROCEDURES AND IES TM-21 CALCULATOR

** ESTIMATED HOURS

NOTE: Information on this Spec Sheet is subject to change, please visit ecosenselighting.com/downloads/rise for the most updated information.

COLOR RENDERING INDEX 80+, 90+

COLOR CONSISTENCY 3-STEP MACADAM ELLIPSE

ALL LUMEN DATA IS FROM 4000K 80CRI FIXTURES. PLEASE SEE PHOTOMETRY SPEC SHEET FOR ADDITIONAL LUMEN DATA.

LUMEN DEPRECIATION WATTS L70 @ 25C L70 @ 50C L90 @ 25C L90 @ 50C

8 - 80 9 - 90* X - For RD, GR, BL, AM

*90 CRI not available in

2500K, 5000K, and 6500K

LO - Low Output

MO - Medium Output

HO - High Output

LOW

MEDIUM

HIGH

>60,500*

>(109,000)**

>60,500*

>(109,000)**

>60,500*

>(181,000)*

>60,500*

>(109,000)**

>60,500*

>(109,000)**

>36,000*

>60,500*

>(109,000)**

>60,500*

>(109,000)**

>60,500*

>(69,800)**

>60,500*

>(109,000)**

>60,500*

>(109,000)**

>33,200*

PERFORMANCE

8 Low Output 618 76 43,982

15 Medium Output 1,062 71 75,623

23 High Output 1,488 65 105,982

WATTS POWER LUMEN OUTPUT EFFICACY CBCP

5° 40° 5° 40° 5°

*SEE PHOTOMETARY CHART FOR LUMEN DATA

1,522

2,280

40°

1,410

2,502

3,748

RISE™

2/4ECOS E N S E LIG HTING .COM

20191216

P • 310.496 . 6255 F • 310.496 . 6256 T • 855.632.6736

855.6 . ECOSEN

ECOSENSE LIGHTING INC.

837 NORTH SPRING STREET

SUITE 103

LOS ANGELES, CA 90012

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.

VISIT ECOSENSELIGHTING.COM FOR THE MOST CURRENT SPECIFICATIONS.

FOR A LIST OF PATENTS VISIT ECOSENSELIGHTING.COM/IP-PORTFOLIO/

©2019 ECOSENSE LIGHTING INC. ALL RIGHTS RESERVED. ECOSENSE, THE

ECOSENSE LOGO, TRoV, TROV AND ECOSPEC ARE REGISTERED TRADEMARKS

OF ECOSENSE LIGHTING INC.

RISE™, SLIM COVE™, FREEDOM TO CREATE™, MACRO™, FLIP-TO-FLAT™ ARE

TRADEMARKS OF ECOSENSE LIGHTING INC.

ELECTRICAL

POWER FACTOR >0.9

STARTUP TEMPERATURE -40˚F TO 122˚F (-40˚C TO 50˚C)

OPERATING VOLTAGE MULTIVOLT: 110-277VAC, 50/60 Hz

OPERATING TEMPERATURE -40˚F TO 122˚F (-40˚C TO 50˚C)

DRIVER INTEGRAL TO FIXTURE; DE-RATED POWER AND SYNCHRONOUS START-UP AT FULL BRIGHTNESS

STORAGE TEMPERATURE -40˚F TO 176˚F (-40˚C TO 80˚C)

WATTAGE LOW OUTPUT = 8W; MEDIUM OUTPUT = 15W; HIGH OUTPUT = 23W

CONTROL DIMMING 110-277VAC, ELV TYPE, REVERSE PHASE, TRAILING EDGE

POWER FACTOR >0.9 for 120V (HO, MO, LO), 230V (HO, MO), 277V (HO)

THD <0.2 for 120V (HO, MO, LO), 230V (HO, MO), 277V (HO)

PHYSICAL DIMENSIONS SEE DIMENSION PAGES

HOUSING/LENS EXTRUDED ALUMINUM; UV STABILIZED POLYCARBONATE; STAINLESS STEEL FASTENERS

WEIGHT 5.0LBS / 2.26KG

WIRING LENGTH OF EXTERIOR CABLE 10’ (3.05m)

MOUNTING OPTIONS B - EXTERNAL CABLE SIDE EXIT; SURFACE MOUNT ; UL LISTED

SURFACE MOUNT PLATE INCLUDED

TOOLS 2.5mm HEX KEY AND PHILLIPS #0 SCREWDRIVER FOR INTERCHANGEABLE LENS + SNOOTS 4mm HEX KEY FOR AIMING 5mm HEX KEY FOR MAIN TILT ARM

CORROSION RESISTANT RISE HAS A HIGH-PERFORMING, CORROSION-RESISTANT FINISH THAT USES HIGH DURABILITY

TRIGLYCIDYL ISOCYANURATE (TGIC) POWDER COATINGS SPECIFICALLY DESIGNED FOR

NATATORIUMS AND EXTERIOR WEATHER EXPOSURE. THIS FINISH HAS BEEN TESTED AND

APPROVED TO MARINE GRADE CORROSION RESISTANCE STANDARD IN UL1598A, ASTM B117 SALT

FOG TEST FOR 200 HOURS.

ENVIRONMENT OUTDOOR • UL CERTIFIED FOR WET LOCATIONS IP66

IMPACT RATED TO IK10

MEETS 3G ANSI C136.31 VIBRATION STANDARD FOR BRIDGE APPLICATIONS WHEN USED WITH

SURFACE MOUNT PLATE (INCLUDED) OR WALL MOUNT ARMS (SOLD SEPERATLY)

WIND LOAD (EPA) EFFECTIVE PROJECTED AREA 2H=0.24ft2 ; 2V=0.39ft2

0-10V CONTROL OPTIONS

All products come standard with ELV dimming capabilities. 0-10V Control options required for operation at 0-10V.

100-120VAC / 277VAC Linear Dimming Control Module 0-10V - Plenum Rated ................................................................................ LDCM-PL-120-277-010V-GR

OPTIONAL ACCESSORIES

Snoots Full Snoot, Color Finish (K=Black, Z=Bronze, S=Silver, W=White, C=Custom) ....................................................................................................... F080-F-(K,Z,S,W,C)

FIXTURE RATING &

CERTIFICATIONS

CE, UL CERTIFIED

RoHS COMPLIANT, IK10

LIMITED WARRANTY 5 YEARS

RoHS

COMPLIANT

IK10

NOTE: Information on this Spec Sheet is subject to change, please visit ecosenselighting.com/downloads/rise for the most updated information.

C - EXTERNAL CABLE BOTTOM EXIT; 1/2” NPT; UL LISTED

SURFACE MOUNT PLATE INCLUDED

Half Multi-Fixture Snoot, Color Finish (K=Black, Z=Bronze, S=Silver, W=White, C=Custom) ......................................................................... F080-HM-(K,Z,S,W,C)

D - EXTERNAL CABLE SIDE EXIT; SURFACE MOUNT ; CE LISTED

SURFACE MOUNT PLATE INCLUDED

E - EXTERNAL CABLE BOTTOM EXIT; SURFACE MOUNT : CE LISTED

SURFACE MOUNT PLATE INCLUDED

Interchangeable Lens

If inner optic = 5°, Desired angle ................................................................................................................................................................... Order the following spread lens 5 Degree .......................................................................................................................................................................................................................................... F080-LENS-05 10 Degree ........................................................................................................................................................................................................................................ F080-LENS-10 15 Degree .......................................................................................................................................................................................................................................... F080-LENS-15 20 Degree ....................................................................................................................................................................................................................................... F080-LENS-20 40 Degree ....................................................................................................................................................................................................................................... F080-LENS-40 60 Degree ....................................................................................................................................................................................................................................... F080-LENS-60 80 Degree ....................................................................................................................................................................................................................................... F080-LENS-80 15x60 or 60x15 Degree ............................................................................................................................................................................................................. F080-LENS-E1E3 30x60 or 60x30 Degree ......................................................................................................................................................................................................... F080-LENS-E2E4 Full Set of Beam Angle Lens Degree (5, 10, 15, 20, 40, 60, 80, 15X60 or 60X15, 30X60 or 60X30) ............................................................... F080-LENS-FULLSET

RISE™

3/4ECOS E N S E LIG HTING .COM

20191216

P • 310.496 . 6255 F • 310.496 . 6256 T • 855.632.6736

855.6 . ECOSEN

ECOSENSE LIGHTING INC.

837 NORTH SPRING STREET

SUITE 103

LOS ANGELES, CA 90012

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.

VISIT ECOSENSELIGHTING.COM FOR THE MOST CURRENT SPECIFICATIONS.

FOR A LIST OF PATENTS VISIT ECOSENSELIGHTING.COM/IP-PORTFOLIO/

©2019 ECOSENSE LIGHTING INC. ALL RIGHTS RESERVED. ECOSENSE, THE

ECOSENSE LOGO, TRoV, TROV AND ECOSPEC ARE REGISTERED TRADEMARKS

OF ECOSENSE LIGHTING INC.

RISE™, SLIM COVE™, FREEDOM TO CREATE™, MACRO™, FLIP-TO-FLAT™ ARE

TRADEMARKS OF ECOSENSE LIGHTING INC.

Honeycomb Louver Honeycomb Louver F080........................................................................................................................................................................................................... F080-LV-HComb

Canopy Plate (Not for use with wire Option B - External Cable Side Exit) RISE Canopy Plate (K=Black, Z=Bronze, S=Silver, W=White, C=Custom) .............................................................................................. RISE-CANOPY-04-(K,Z,S,W,C)

If inner optic = 40°, Desired angle ..................................................................................................................................................................... Order the following spread lens 5 Degree ....................................................................................................................................................................................................................................... NOT SUPPORTED 10 Degree ..................................................................................................................................................................................................................................... NOT SUPPORTED 15 Degree ....................................................................................................................................................................................................................................... NOT SUPPORTED 20 Degree ...................................................................................................................................................................................................................................... NOT SUPPORTED 40 Degree .......................................................................................................................................................................................................................................... F080-LENS-10 60 Degree ........................................................................................................................................................................................................................................... F080-LENS-40 70 Degree ........................................................................................................................................................................................................................................... F080-LENS-60 90 Degree .......................................................................................................................................................................................................................................... F080-LENS-80 15x60 or 60x15 Degree ............................................................................................................................................................................................................... NOT SUPPORTED 30x60 or 60x30 Degree ............................................................................................................................................................................................................ NOT SUPPORTED Full Set of Beam Angle Lens Degree (5, 10, 15, 20, 40, 60, 80, 15X60 or 60X15, 30X60 or 60X30) .................................................................. F080-LENS-FULLSET

Color Filters Red ............................................................................................................................................................................................................................................ F080-FILTER-RED Blue .......................................................................................................................................................................................................................................... F080-FILTER-BLUE Green .................................................................................................................................................................................................................................... F080-FILTER-GREEN Amber .................................................................................................................................................................................................................................. F080-FILTER-AMBER

F080 Multi-Fixture (DUO, QUAD) Wall Mount Arm (for use only with Wiring Option C - External Cable Bottom Exit) Wall Mount Arm, 6 inch, Color Finish (K=Black, Z=Bronze, S=Silver, W=White, C=Custom) ................................................................ F170-WMA-06-(K,Z,S,W,C) Wall Mount Arm, 12 inch, Color Finish (K=Black, Z=Bronze, S=Silver, W=White, C=Custom) ................................................................. F170-WMA-12-(K,Z,S,W,C) Wall Mount Arm, 18 inch, Color Finish (K=Black, Z=Bronze, S=Silver, W=White, C=Custom) ................................................................ F170-WMA-18-(K,Z,S,W,C) Wall Mount Arm, 24 inch, Color Finish (K=Black, Z=Bronze, S=Silver, W=White, C=Custom) ................................................................. F170-WMA-24-(K,Z,S,W,C)

Ground Stake (for use only with Wiring Option C - External Cable Bottom Exit) Landscape Stake, 12in ............................................................................................................................................................................................................ F170-LS-1S-STK-12

DIMENSIONS - F080 2V (VERTICAL)

inch mm inch mm

3.47

88.04

10.38

263.72

5.

1.

2.50 63.50

3.09 78.50

3.35 85.02

.5

9.

5.19

131.81

NOTE: Information on this Spec Sheet is subject to change, please visit ecosenselighting.com/downloads/rise for the most updated information.

RISE™

4/4ECOS E N S E LIG HTING .COM

20191216

P • 310.496 . 6255 F • 310.496 . 6256 T • 855.632.6736

855.6 . ECOSEN

ECOSENSE LIGHTING INC.

837 NORTH SPRING STREET

SUITE 103

LOS ANGELES, CA 90012

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.

VISIT ECOSENSELIGHTING.COM FOR THE MOST CURRENT SPECIFICATIONS.

FOR A LIST OF PATENTS VISIT ECOSENSELIGHTING.COM/IP-PORTFOLIO/

©2019 ECOSENSE LIGHTING INC. ALL RIGHTS RESERVED. ECOSENSE, THE

ECOSENSE LOGO, TRoV, TROV AND ECOSPEC ARE REGISTERED TRADEMARKS

OF ECOSENSE LIGHTING INC.

RISE™, SLIM COVE™, FREEDOM TO CREATE™, MACRO™, FLIP-TO-FLAT™ ARE

TRADEMARKS OF ECOSENSE LIGHTING INC.

DIMENSIONS - F080 2H (HORIZONTAL)

10.38

263.72

4.72

120.00

6.51

165.45

2.50

63.50

2.49

63.31

.5

9.

5.17

131.41

NOTE: Information on this Spec Sheet is subject to change, please visit ecosenselighting.com/downloads/rise for the most updated information.

FIXTURE SPECIFICATIONS:

MODEL 1188 Architectural Series • Inground & Well Lights

SPECIFICATION SHEET

DIMENSIONS:

DOOR:

Die-cast, low copper content, A360 aluminum. Post anodized Type III (hard anodized) and powder coated for maximum corrosion protection.

Captive stainless steel fasteners affixed to a ventilated door. Inner vents allow hot air to escape from around optic housing while outer vents allow cool air to enter fixture housing.

FIXTURE HOUSING:

Compression-molded, glass-reinforced polymer for strength and high UV stability. Molded with integral junction box. Unibody construction allows for superior door and optic housing support. J-box comes standard with two ¾” NPT bottom B34 tapped holes. ¾” NPT front F34, ¾” NPT side S34 and ¾” NPT all A34 conduit entry holes optional (Consult Factory).

OPTIC HOUSING:

Die-cast A360 aluminum. Finned for maximum heat disapation. Type III hard anodized and Thermkote treated for maximum corrosion protection.

Optic and driver compartment separately sealed while being electrically connected.

DRIVER COMPARTMENT:

Injection molded PPS for maximum corrosion protection. Driver compartment houses electronic LED driver and thermostat which cuts power to fixture in abnormal ambient temperature conditions. Driver compartment is completely epoxy potted to protect electronics from moisture.

DOOR FINISH:

Durable powder coat finish available in Black, Architectural Bronze, Dark Bronze, Granite, White, Architectural Brick, Light Bronze, Special Bronze, Glossy Gray, Rust, Hunter Green, Weathered Bronze, Weathered Iron, Graphite Metallic, Verde, Pewter, Mocha and Olde Finish. Custom Powder coat finishes available on request.

LED:

Cree® CXA 3050COB driven at 700mA, 800mA, or 900mA.

CRI:

The CRI range is 83 - 84.

COLOR TEMPERATURE:

LED’s are offered in 2700°K, 3000°K, 3500°K, 4000°K, or 5000°K CCT ANSI white 4 step Cree® East White™ bins

LIGHT DISTRIBUTION:

Very Narrow Spot VNS (NEMA 2x2), Narrow Spot NS (NEMA 2x2), Medium Flood MF (NEMA 4x4), and Wide Flood WF (NEMA 6x6).

REFLECTOR:

Specular or semi-specular optics designed for maximum performance and uniformity. Very Narrow Spot VNS optic incorporates an internal source shield to eliminate unwanted glare outside the beam pattern.

LENS/SEAL:

½” thick tempered pressed clear glass sealed with a solid molded silicone gasket.

WIRING:

3’ 18/3 outdoor-rated hard usage cable standard for non-dimming ND and Phase Cut TRIAC (120V only) dimming PCT fixtures. 3’ 18/5 outdoor-rated hard usage cable standard for 0-10V dimming 010 fixtures. Cable exits fixture housing through a liquid tight cable fitting.

DRIVER:

Integral CUL listed LED driver, either non-dimmable ND or dimmable.

Dimming: 0-10VDC 010 and Phase Cut TRIAC (120V only) PCT options available. Multi-Volt MV 120V-277V driver input standard.

ACCESSORIES:

TO5 - Tilt Optic 5°, TO10 - Tilt Optic 10°, TO15 - Tilt Optic 15°, TO25 - Tilt Optic 25°, DF - Diffuse Filter, LSF - Linear Spread Filter, RBK - Rebar Bracket Kit, STR - Stainless Trim Ring, and HS - Half Glare Shield. Dichroic Lenses: YL - Yellow, RL - Red, BL - Blue, GL - Green.

MOUNTING:

Fixture suitable for direct burial in earth or poured concrete applications.

CERTIFICATION:

C ETL US wet location listed. IP68

All Vista Architectural luminaires are MADE IN THE U.S.A.

1625 Surveyor Avenue • Simi Valley, CA 93063 • (805) 527-0987 • (800) 766-VISTA (8478) FAX: (888) 670-VISTA (8478) • email@vistapro.com • www.vistapro.com

Vista Professional Outdoor Lighting reserves the right to modify the design and/or construction of the fixture shown without further notification.

Type:

Model:

Project:

12” 304.8mm

12” 304.8mm

4⅝” 118.3mm

2½” 63.5mm

F34

¾” NPT FRONT

TAPPED HOLE

(2 PLCS)

OPTIONAL

S34

¾” NPT SIDE

TAPPED HOLE

(2 PLCS)

OPTIONAL

4⅝” 118.3mm

4” 103.2mm

4⅛” 104.8mm

2¾” 69.9mm

MOUNTING HOLE (4 PLCS)

STANDARD FOR OPTIONAL

REBAR MOUNT BRACKET (RMB)

DRAIN HOLE

(4 PLCS)

STANDARD

¾” NPT BOTTOM

TAPPED HOLE

(2 PLCS)

STANDARD

TOP VIEW FRONT VIEW SIDE VIEW BOTTOM VIEW

1625 Surveyor Avenue • Simi Valley, CA 93063 • (805) 527-0987 • (800) 766-VISTA (8478) FAX: (888) 670-VISTA (8478) • email@vistapro.com • www.vistapro.com

FIXTURE ORDERING INFORMATION

TO ORDER FIXTURE: Select appropriate choice from each column as in the following example.

EXAMPLE: 1188-GG-NS-30-A-MV-CX-ND-F34-TO5

MODEL 1188 Architectural Series • Inground & Well Lights

SPECIFICATION SHEET

Vista Professional Outdoor Lighting reserves the right to modify the design and/or construction of the fixture shown without further notification.

LED:

• High lumen output LED powered for high efficacy

• Cree® CXA 3050 COB driven at 700mA, 800mA, or 900mA.

• 2700°K, 3000°K, 3500°K, 4000°K, or 5000°K CCT ANSI white 4 step

Cree® Easy White™ bins.

• 1150- 3248 Delivered Lumens

• 25-35 Watts

OPTICS/AIMING:

• Specular or semi-specular optics designed for maximum performance and uniformity.

• Very Narrow Spot VNS (NEMA 2x2), Narrow Spot NS (NEMA 2x2), Medium Flood MF (NEMA 4x4), and Wide Flood WF (NEMA 6x6).

• Fixture aiming achieved via a series of tilt optic lenses and patent pending magnetic aiming system.

ELECTRICAL:

• Constant current 700mA, 800mA, or 900mA output driver.

• Multi-Volt MV 120V-277V universal input.

• 3’ 18/3 outdoor-rated hard usage cable standard for non-dimming fixtures and Phase Cut TRIAC PCT dimming fixtures.

• 3’ 18/5 outdoor-rated hard usage cable standard for 0-10V dimming fixtures.

1188 SERIES-LOAD RATING:

• Peak compressive force of 8,000 lbs. This represents 95% of max load to load failure on average. Independent tests performed by SGS US Testing Company, Inc., an ISO 17025 accredited National Testing Laboratory.

LAMP SPECIFICATIONS

MODEL DOOR FINISH DISTRIBUTION COLOR TEMPERATURE DELIVERED LUMENS

1188 Standard B - Black Z - Architectural Bronze DZ - Dark Bronze GT - Granite W - White Premium BR - Architectural Brick LZ - Light Bronze SB - Special Bronze GG - Glossy Gray R - Rust HG - Hunter Green WB - Weathered Bronze WI - Weathered Iron GM - Graphite Metallic Hand Finished G - Verde P - Pewter M - Mocha OF - Olde Finish

VNS - Very Narrow Spot NS - Narrow Spot MF - Medium Flood WF - Wide Flood

27 - 2700°K 30 - 3000°K 35 - 3500°K 40 - 4000°K 50 - 5000°K

A - 1500-2000 B - 2000- 2500 C - 2500-3000

1188-VNS not available with B & C lumen packages.

VOLTAGE LENS DIMMING CONDUIT ENTRIES ACCESSORIES

MV - Multi-Volt (120V-277V)

CX - Crowned Clear AX - Anti Slip Clear

ND - No Dimming 010 - 0-10V PCT - Phase Cut TRIAC (120V only)

B34 - Bottom ¾ “ (standard)

TO5 - Tilt Optic 5° TO10 - Tilt Optic 10° TO15 - Tilt Optic 15° TO25 - Tilt Optic 25° DF - Diffuse Filter LSF - Linear Spread Filter

RBK - Rebar Bracket Kit STR - Stainless Trim Ring HS - Half Glare Shield YL - Yellow Lens RL - Red Lens BL - Blue Lens GL - Green Lens *Colored Lenses not available with B & C Lumen packages.

F34 - Front ¾” S34 - Sides ¾” A34 - All ¾” (available as an option) (Consult Factory)

MODEL 1188 Architectural Series • Inground & Well Lights

SPECIFICATION SHEET

LUMEN OUTPUT PACKAGES Watts Lumens

1625 Surveyor Avenue • Simi Valley, CA 93063 • (805) 527-0987 • (800) 766-VISTA (8478) FAX: (888) 670-VISTA (8478) • email@vistapro.com • www.vistapro.com 1188 3.20.20

Vista Professional Outdoor Lighting reserves the right to modify the design and/or construction of the fixture shown without further notification.

Beam Spread A B C

VNS

34.9 Watts

1698.9 Lumens

NS

31.5 Watts 35.9 Watts 36.7 Watts

2180 Lumens 2488 Lumens 2796 Lumens

MF

30.7 Watts 35.0 Watts 35.8 Watts

2120 Lumens 2418 Lumens 2718 Lumens

WF

32.4 Watts 37.0 Watts 37.8 Watts

2532 Lumens 2891 Lumens 3248 Lumens

Anaheim Convention Center, CA

The TL310/410-WCS Series Plugging Boxes are recessed wall mounted or free-standing pedestal mounted enclosures designed for the temporary connection of electrical devices in exterior applications.

Cast covers feature a unique cord slot system that prevents ingress of water from rain and sprinklers.

Plugging Boxes are appropriate in parks, schools, convention centers and other public gathering areas for connection of power and AV equipment.

Wet Location While In Use

C.W. Cole & Company, Inc.

2560 Rosemead Boulevard South El Monte, CA 91733-1593 Tel. (626) 443-2473 Fax (626) 443-9253 info@colelighting.com www.colelighting.com

TL310/TL410-WCS

SERIES

TL310-WCS

Two-gang capacity

-GFCI

duplex

-RJ11

1-6 jacks per insert

Device Capacity Chart

Mixed and matched quantities not to exceed total in any column.

-RJ45

1-6 jacks per insert

-USB

1-6 jacks per insert

-HDMI

1-6 jacks per insert

SPECIFICATIONS

Construction Cover is cast aluminum with self-closing, locking door • All units keyed alike • Cord slots backed with a rubber baffle system prevents the ingress of water • Recessed housing is 16 gauge electro-galvanized steel • Pedestal models are 1/8" aluminum • Cover and housing coated with metallic aluminum polyester powder coating

Electrical Various wiring device combinations are available as indicated with catalog suffixes • Barrier pro-vided between high and low voltage devices

• Recessed housing has eight 1/2"- 3/4"-1" com-bination trade-size knockouts • Pedestal allows for two conduit stub-ups • ETL listed while in use

Mounting Recessed housing suitable for concrete pour.

Pedestal models include four 4" 5/16-18 stainless steel sleeve anchors.

How to Specify

1. Select catalog number with desired features.

2. Add suffixes for options required to meet job conditions. When requesting device in multiples please add suffix and quantity seperated by a slash. Example: Two GFCI and one RJ45 device

= -GFCI/2-RJ45/1

Weather resistant /tamper resistant receptacle -GFCI

Telephone or data connection in modular Decora® cutout -RJ11 or -RJ45

Universal Serial Bus port -USB

High-definition multimedia interface -HDMI

Specify device to be installed or desired provisions-only -9/(device or provisions) 30 amp or greater will require deep housing -9/(indicate receptacle)

Installed Devices

Options Bronze cover: Satin finished, clear coated.

(Recessed only) Add suffix -B.

Pedestal height over 6": Add suffix -PED/(height).

No key: Add suffix -NK.

Custom color: Contact factory. Add suffix -CC.

ADA compliant pedestal: Add suffix -PED/ADA.

Maintains the minimum ADA required 15" receptacle height when pedestal is mounted at grade.

Catalog Numbers

Recessed/Deep housing, solid receptacle plate with voltage barrier TL310-WCS Recessed/Shallow housing, solid receptacle plate with voltage barrier TL310-WCS-SH 6" Pedestal housing, solid receptacle plate with voltage barrier TL310-WCS-PED

Deep Housing Shallow Housing Shallow Housing Front View

TL310-WCS Series

Wet Location While In Use

TL310-WCS-SH TL310-WCS-B-NK TL310-WCS-PED

Pedestal

Seam welded all around

5-3/4" (146mm)

3" (76mm)

3-7/8" (98mm) 10-3/4" (273mm)

7-1/2"sq.(191mm) trim

Device mounting area: 4" x 4"

(102mm x 102mm)

3/8" (76mm)Typ.

5-1/2" (114mm)

7-1/2"sq.

(191mm)

8-1/2" (216mm)

3-3/4" (95mm) Inside dimension

10-1/2" (267mm)

5-3/4" (146mm) Inside dimension

6" (152mm)

High/Low voltages protected by barrier

13-1/2" (381mm)

22-1/2" ADA

(572mm)

7-1/2" sq (191mm) trim

5-3/4" (146mm)

5-3/4" (146mm)

6-1/8"sq.

(156mm)

5-1/2" (140mm) 2-9/16" (65mm)

2" (51mm)

C.W. Cole & Company, Inc. | T: 626.443.2473 | F: 626.443.9253 | www.colelighting.com | info@colelighting.com

Options

Bronze cover: Satin finished, clear coated.

(Recessed only) Add suffix -B.

Pedestal height over 6": Add suffix -PED/(height).

No key: Add suffix -NK.

Custom color: Contact factory. Add suffix -CC.

ADA compliant pedestal:

Add suffix -PED/ADA.

Maintains the minimum ADA required 15" receptacle height when pedestal is mounted at grade.

SPECIFICATIONS

Construction Cover is cast aluminum with self-closing, locking door • All units keyed alike • Cord slots backed with a rubber baffle system prevents the ingress of water • Recessed housing is 16 gauge electro-galvanized steel • Pedestal models are 1/8" aluminum…