MIST II Enclosure CC - GPM Amendment 2.pdf

ENCLOSURE CC

GOVERNMENT PRICING MODEL (GPM) – SPECIFIED

NON-MANAGEMENT

DIRECT LABOR CATEGORIES, DIRECT LABOR HOURS

AND POSITION DESCRIPTIONS

RFP 80GSFC20R0006

Amendment 2

RFP 80GSFC20R0006 Amendment 2 Enclosure CC

Government Pricing Model (GPM)-Specified Non-Management Direct Labor Categories and Direct Labor Hours By Site Location

Direct Labor Categories CY1 CY2 CY3 CY4 CY5 Chief Eng 34,765 34,765 34,765 34,765 34,765 Contamination Eng 4,778 4,778 4,778 4,778 4,778 Contamination Eng Jr 2,197 2,197 2,197 2,197 2,197 Contamination Eng Sr 4,595 4,595 4,595 4,595 4,595 Contamination Eng SME 2,055 2,055 2,055 2,055 2,055 Cryogenics Eng 4 4 4 4 4 Cryogenics Eng Sr 198 198 198 198 198 Cryogenics Eng SME 34 34 34 34 34 Elctromec Sys Eng 1,837 1,837 1,837 1,837 1,837 Elctromec Sys Eng Sr 11,548 11,548 11,548 11,548 11,548 Elctromec Sys Eng SME 2,343 2,343 2,343 2,343 2,343 Elect Eng Analog 2,939 2,939 2,939 2,939 2,939 Elect Eng Digital 2,830 2,830 2,830 2,830 2,830 Elect Eng Jr 4 4 4 4 4 Elect Eng Sr 8,814 8,814 8,814 8,814 8,814 Elect Eng SME 1,274 1,274 1,274 1,274 1,274 Electronic Tech 1,909 1,909 1,909 1,909 1,909 Electronic Tech Jr 733 733 733 733 733 Electronic Tech Sr 1,833 1,833 1,833 1,833 1,833 Electro-Optical Eng 2,096 2,096 2,096 2,096 2,096 Electro-Optical Eng Sr 762 762 762 762 762 Electro-Optical Eng SME 4 4 4 4 4 Eng Analysis Tech 10,424 10,424 10,424 10,424 10,424 Materials Eng 2,088 2,088 2,088 2,088 2,088 Materials Eng Jr 1,095 1,095 1,095 1,095 1,095 Materials Eng Sr 1,166 1,166 1,166 1,166 1,166 Materials Eng SME 817 817 817 817 817 Materials Eng Tech 1,785 1,785 1,785 1,785 1,785 Mech Designer 5,009 5,009 5,009 5,009 5,009 Mech Designer Jr 776 776 776 776 776 Mech Designer Sr 13,091 13,091 13,091 13,091 13,091 Mech Eng 3,900 3,900 3,900 3,900 3,900 Mech Eng Jr 7,898 7,898 7,898 7,898 7,898 Mech Eng Sr 13,333 13,333 13,333 13,333 13,333 Mech Eng SME 4,335 4,335 4,335 4,335 4,335 Mech Systems Eng 7,021 7,021 7,021 7,021 7,021 Mech Systems Eng Sr 24,748 24,748 24,748 24,748 24,748 Mech Systems Eng SME 4,654 4,654 4,654 4,654 4,654 Mech Tech 2,767 2,767 2,767 2,767 2,767 Mech Tech Jr 995 995 995 995 995 Mech Tech Sr 11,327 11,327 11,327 11,327 11,327 Metrology Tech 7,520 7,520 7,520 7,520 7,520 Optical Analyst 3,373 3,373 3,373 3,373 3,373 Optical Analyst Sr 5,079 5,079 5,079 5,079 5,079 Optical Systems Analyst 3,373 3,373 3,373 3,373 3,373 Optical Systems Analyst Sr 5,079 5,079 5,079 5,079 5,079 Proj Staff Eng Sr 122,606 122,606 122,606 122,606 122,606 Stress Analysis Eng 2,693 2,693 2,693 2,693 2,693 Stress Analysis Eng Sr 3,219 3,219 3,219 3,219 3,219 Stress Analysis SME 2,013 2,013 2,013 2,013 2,013 Struct Dyn Eng 4 4 4 4 4 Struct Dyn Eng Jr 4 4 4 4 4 Struct Dyn Eng Sr 19,201 19,201 19,201 19,201 19,201 Struct Dyn Eng SME 3,344 3,344 3,344 3,344 3,344 Test and Int Eng 5,080 5,080 5,080 5,080 5,080 Test and Int Eng Sr 16,283 16,283 16,283 16,283 16,283 Test and Int Tech 6,954 6,954 6,954 6,954 6,954 Test and Int Tech Sr 13,285 13,285 13,285 13,285 13,285 Thermal Coatings Eng 1,669 1,669 1,669 1,669 1,669 Thermal Coatings Eng Sr 1,822 1,822 1,822 1,822 1,822 Thermal Dev Eng 2,781 2,781 2,781 2,781 2,781 Thermal Dev Eng Sr 1,506 1,506 1,506 1,506 1,506 Thermal Eng 6,488 6,488 6,488 6,488 6,488 Thermal Eng Jr 4,383 4,383 4,383 4,383 4,383 Thermal Eng Sr 8,887 8,887 8,887 8,887 8,887 Thermal Eng SME 3,700 3,700 3,700 3,700 3,700 Total Onsite Hours 455,127 455,127 455,127 455,127 455,127

ONSITE GPM - Specified Non-Management

Total Onsite Hours 455,127 455,127 455,127 455,127 455,127

CY1 CY2 CY3 CY4 CY5

Chief Eng 14,057 14,057 14,057 14,057 14,057 Contamination Eng 142 142 142 142 142 Elctromec Sys Eng 243 243 243 243 243 Elect Eng Analog 1,167 1,167 1,167 1,167 1,167 Elect Eng Sr 4,988 4,988 4,988 4,988 4,988 Elect Eng SME 637 637 637 637 637 Electronic Tech 4,140 4,140 4,140 4,140 4,140 Electronic Tech Jr 1,147 1,147 1,147 1,147 1,147 Electronic Tech Sr 1,020 1,020 1,020 1,020 1,020 Electro-Optical Eng 66 66 66 66 66 Electro-Optical Eng Sr 4,602 4,602 4,602 4,602 4,602 Electro-Optical Eng SME 1,364 1,364 1,364 1,364 1,364 Eng Analysis Tech 3,810 3,810 3,810 3,810 3,810 Materials Eng 83 83 83 83 83 Materials Eng Jr 23 23 23 23 23 Materials Eng Sr 175 175 175 175 175 Materials Eng Tech 95 95 95 95 95 Mech Designer 269 269 269 269 269 Mech Designer Jr 1,430 1,430 1,430 1,430 1,430 Mech Designer Sr 1,862 1,862 1,862 1,862 1,862 Mech Eng 12,231 12,231 12,231 12,231 12,231 Mech Eng Jr 5,149 5,149 5,149 5,149 5,149 Mech Eng Sr 4,745 4,745 4,745 4,745 4,745 Mech Eng SME 4,335 4,335 4,335 4,335 4,335 Mech Systems Eng 1,865 1,865 1,865 1,865 1,865 Mech Systems Eng Sr 2,448 2,448 2,448 2,448 2,448 Mech Systems Eng SME 1,551 1,551 1,551 1,551 1,551 Mech Tech 5,020 5,020 5,020 5,020 5,020 Mech Tech Jr 885 885 885 885 885 Mech Tech Sr 696 696 696 696 696 Metrology Tech 7,520 7,520 7,520 7,520 7,520 Optical Analyst Sr 89 89 89 89 89 Optical Systems Analyst Sr 89 89 89 89 89 Proj Staff Eng Sr 13,082 13,082 13,082 13,082 13,082 Stress Analysis Eng 14 14 14 14 14 Stress Analysis Eng Sr 1,199 1,199 1,199 1,199 1,199 Stress Analysis SME 4,022 4,022 4,022 4,022 4,022 Struct Dyn Eng 330 330 330 330 330 Struct Dyn Eng Jr 2,005 2,005 2,005 2,005 2,005 Struct Dyn Eng Sr 4,511 4,511 4,511 4,511 4,511 Struct Dyn Eng SME 1,344 1,344 1,344 1,344 1,344 Test and Int Eng 2,900 2,900 2,900 2,900 2,900 Test and Int Eng Sr 933 933 933 933 933 Test and Int Tech 2,564 2,564 2,564 2,564 2,564 Test and Int Tech Sr 1,955 1,955 1,955 1,955 1,955 Thermal Eng 699 699 699 699 699 Thermal Eng Jr 4,404 4,404 4,404 4,404 4,404 Thermal Eng Sr 3,597 3,597 3,597 3,597 3,597 Thermal Eng SME 1,501 1,501 1,501 1,501 1,501 Total Offsite Hours 133,003 133,003 133,003 133,003 133,003

GRAND TOTAL 588,130 588,130 588,130 588,130 588,130

Direct Labor Categories Direct Labor Categories

OFFSITE GPM - Specified Non-Management

GRAND TOTAL 588,130 588,130 588,130 588,130 588,130

*CY – Contract Year

GPM-Specified Non-Management Direct Labor Position Descriptions

Position Title Duties Education Experience Chief Engineer Supports complex and/or technologically challenging tasks including providing leadership in the generation the Task Plan and Work Control Plan, providing guidance during the task implementation, conducting technology assessments and making recommendations for technology insertions, making trade study assessments, and recommendations, supporting CDR and PDR, and reviewing deliverables, providing technical consultation advice to Task Managers regarding design issues, development and test approaches, and test result assessments.

He/she leads teams established by the Program Manager to conduct investigations of programmatic or task- level problems and to make recommendations for recovery plans; provides recommendations regarding Mission Assurance- Program Implementation considerations; and provides world- renowned expertise in space and/or ground hardware and/or software systems for analysis, design, development, integration, test, validation, and orbital operations.

BS/BA

YOE (20)

Sr. Project Staff Engineer

Develops task plans, budgets and schedules from a set of technical task requirements provided by the contracting officer and/or the contracting officer’s representative. Manages engineer and designer teams to address specific tasks. Provides guidance and direction in development and maintenance budgets and schedules. Serves as technical expert advisor, providing the technical approach to resolving task challenges and/or problems.

BS

YOE (10)

Materials Engineer, Subject Matter Expert (SME)

Ensures the safety and success of the mission by the appropriate selection, processing, inspection, and testing of the materials employed to the operational requirement of the application.

Provides direction and guidance to lower level Materials Engineers. Generates and maintains materials lists per the requirements of the task.

Issues Material Usage Agreements for government approval, when applicable. Supports requirements definition, review and verification at the mission, instrument, subsystem and component level.

Supports all types of reviews throughout program planning and execution.

YOE (15)

Senior Materials

Engineer Ensures the safety and success of the mission by the appropriate selection, processing, inspection, and testing of the materials employed to the operational requirement of the application.

Provides direction and guidance to lower level Materials Engineers. Generates and maintains materials lists per the requirements of the task.

Issues Material Usage Agreements for government approval, when applicable.

Materials Engineer Ensures the safety and success of the mission by the appropriate selection, processing, inspection, and testing of the materials employed to the operational requirement of the application Generates and maintains materials lists per the requirements of the task, with minimal guidance from a Senior Materials Engineer. Issues Material Usage Agreements for government approval, when applicable.

YOE (5)

Junior Materials Engineer

Under the direction of a Senior Materials Engineer, ensures the safety and success of the mission by the appropriate selection, processing, inspection, and testing of the materials employed to the operational requirement of the application Generates and maintains materials lists per the requirements of the task. Issues Material Usage Agreements for government approval, when applicable.

BS

Materials Engineering Technician

Supports materials engineers with preparation of engineering data, plots, reports, and other documentation as well as performing engineering tests as directed.

YOE (1)

Structural Dynamics Engineer, Subject

Matter Expert

(SME)

Provides leadership in developing new analytical tools in response to task requirements. Supports the development of structural designs. Analyzes and evaluates structural performance to show that specified requirements are satisfied. Supports testing of structural designs. Provides direction and guidance to lower level Structural Analysis Engineers. Supports requirements definition, review and verification at the mission, instrument, subsystem and component level. Supports all types of reviews throughout program planning and execution.

Senior Dynamics Structural Engineer

Provides leadership in developing new analytical tools in response to task requirements. Supports the development of structural designs. Analyzes and evaluates structural performance to show that specified requirements are satisfied. Supports testing of structural designs. Provides direction and guidance to lower level Structural Analysis Engineers.

Structural Dynamics

Develops new analytical tools in response to task requirements. Under the guidance of a Senior Structural Analysis Engineer as needed, supports the development of structural designs. Analyzes and evaluates structural performance to show that specified requirements are satisfied. Supports testing of structural designs. Provides guidance to lower level Structural Analysis Engineers.

Junior Structural Dynamics Engineer

Under the direction of a Senior Structural Analysis Engineer, supports the development of structural designs. Analyzes and evaluates structural performance to show that specified requirements are satisfied. Supports testing of structural designs.

Stress Analysis Engineer, Subject

Matter Expert

(SME)

Provides leadership in developing new analytical tools in response to task requirements. Supports the development of structural designs. Analyzes and evaluates structural performance to show that specified requirements are satisfied. Supports testing of structural designs. Provides direction and guidance to lower level Structural Analysis Engineers. Supports requirements definition, review and verification at the mission, instrument, subsystem and component level. Supports all types of reviews throughout program planning and

Senior Stress Analysis Engineer

Provides leadership in developing new analytical tools in response to task requirements. Under the direction of the Senior Project Staff Engineer, supports the development of structural designs.

Analyzes and evaluates structural strength to show that specified requirements are satisfied. Supports testing of structural designs. Provides direction and guidance to lower level Stress Analysis Engineer.

Stress Analysis Engineer

Develops new analytical tools in response to task requirements. Under the direction of a Senior Stress Analysis Engineer, supports the development of structural designs. Analyzes and evaluates structural strength to show that specified requirements are satisfied.

Supports testing of structural designs. Provides direction and guidance to lower level Stress Analysis Engineers.

Mechanical

Matter Expert

(SME)

Supports the development of structural designs.

Supports the conception, analysis, design, fabrication, integration, testing, deployment, maintenance, and certification of mechanical systems, mechanisms, and related ground support and test equipment Tasks may include, but are not limited to: math modeling, dynamic analyses, static strength analyses, mass properties calculations, test hardware set-up, and conceptual designs. Performs interface definition, examines designs for proper form, fit, and function. Develops test plans and procedures, and assists in the reduction/analysis of test data. Supports requirements definition, review and verification at the mission, instrument, subsystem and component level. Supports all types of reviews throughout program planning and

Senior Mechanical Engineer

Supports the development of structural designs.

Supports the conception, analysis, design, fabrication, integration, testing, deployment, maintenance, and certification of mechanical systems, mechanisms, and related ground support and test equipment Tasks may include, but are not limited to: math modeling, dynamic analyses, static strength analyses, mass properties calculations, test hardware set-up, and conceptual designs. Performs interface definition, examines designs for proper form, fit, and function. Develops test plans and procedures, and assists in the reduction/analysis of test data.

Engineer

Under the direction or guidance of a Senior Mechanical Engineer, supports the development of structural designs. Supports the conception, analysis, design, fabrication, integration, testing, deployment, maintenance, and certification of mechanical systems, mechanisms, and related ground support and test equipment Tasks may include, but are not limited to: math modeling, dynamic analyses, static strength analyses, mass properties calculations, test hardware set-up, and conceptual designs. Performs interface definition, examines designs for proper form, fit, and function.

Develops test plans and procedures, and assists in the reduction/analysis of test data.

Junior Mechanical

Under the direction of a Senior or mid-level Mechanical Engineer, supports the development of structural designs. Tasks may include, but are not limited to: math modeling, dynamic analyses, static strength analyses, mass properties calculations, test hardware set-up, and conceptual designs. Performs interface definition, examines designs for proper form, fit, and function. Develops test plans and procedures, and assists in the reduction/analysis of test data.

BS or equivalent Must be within 12 months of completing Degree

Mechanical Systems

Matter

Provides leadership in the development of hardware designs which meet specified requirements. Performs or directs mechanical engineering tasks to assure proper form, fit and function. Assures design suitability for fabrication, mass pro54perty control, material suitability, interface definition. Develops and implements test plans and procedures. Provides direction and guidance to lower level Mechanical Systems Engineers. Supports requirements definition, review and verification at the mission, instrument, subsystem and component level. Supports all types of reviews throughout program planning and

Systems Engineer

Provides leadership in the development of hardware designs which meet specified requirements. Performs or directs mechanical engineering tasks to assure proper form, fit and function. Assures design suitability for fabrication, mass property control, material suitability, interface definition. Develops and implements test plans and procedures. Provides direction and guidance to lower level Mechanical Systems Engineers.

Mechanical Systems Engineer

Under the direction of the Senior Mechanical Systems Engineer, supports the development of hardware designs which meet specified requirements. Performs or directs mechanical engineering tasks to assure proper form, fit and function. Assures design suitability for fabrication, mass property control, material suitability, interface definition. Develops and implements test plans and procedures.

Designer

Analyzes processes or operations with the intent to improve efficiency usually in the field of information technology. Assigned to a problem which he/she then researches, gathers, and writes requirements, makes recommendations, and works with technical staff to implement. Extensive knowledge of GSFC Engineering Drawing Requirements Manual, 500-PG- 8700.2.5C and Dimensioning and Tolerancing per ASME Y14.5M is required.

Designer Under the direction of a Senior Mechanical Designer, directs or performs geometrical layout studies, sizing calculations, and generates mechanical drawings representing designs that satisfy all requirements. Provides direction to lower level Mechanical Designers. Extensive knowledge of GSFC Engineering Drawing Requirements Manual, 500-PG-8700.2.5C and Dimensioning and Tolerancing per ASME Y14.5M is required.

YOE (5)

Junior Mechanical Designer

Under the direction of a Senior or mid-level Mechanical Designer, directs or performs geometrical layout studies, sizing calculations, and generates mechanical drawings representing designs that satisfy all requirements. Extensive knowledge of GSFC Engineering Drawing Requirements Manual, 500-PG-8700.2.5C and Dimensioning and Tolerancing per ASME Y14.5M is required.

YOE (1)

Senior Mechanical Technician

Sets up and operates machines such as lathes, milling machines, shapers, jig bores, brakes, shears, and heavy duty presses. Cuts, bends, align, and forms metal plates, sheets, and structural shapes as specified by engineering drawings, layouts, and templates. Read engineering drawings for product specifications such as dimensions and tolerances, and tooling instructions. May be required to operate grinder, spot welder, and other machine tools.

Assemble hardware as specified by engineering drawings. Assist in the performance of mechanical tests.

YOE (10)

Mechanical Technician

Under the direction or guidance of a Senior Mechanical Technician, sets up and operates machines such as lathes, milling machines, shapers, jig bores, brakes, shears, and heavy duty presses.

Cut, bend, align, and form metal plates, sheets, and structural shapes as specified by engineering drawings, layouts, and templates. Read engineering drawings for product specifications such as dimensions and tolerances, and tooling instructions.

May be required to operate grinder, spot welder, and other machine tools. Assemble hardware as specified by engineering drawings. Assist in the performance of mechanical tests.

Junior Mechanical

Technician Under the direction or guidance of a Mechanical Technician, sets up and operates machines such as lathes, milling machines, shapers, jig bores, brakes, shears, and heavy duty presses. Cut, bend, align, and form metal plates, sheets, and structural shapes as specified by engineering drawings, layouts, and templates. Read engineering drawings for product specifications such as dimensions and tolerances, and tooling instructions. May be required to operate grinder, spot welder, and other machine tools. Assemble hardware as specified by engineering drawings. Assist in the performance of mechanical tests.

YOE (1)

Electrical Engineer, Subject Matter Expert ( SME)

Interprets system level requirements as they apply to the development of electrical systems and components, identifies design alternatives and performs trade-off studies, error budget, sensitivity, reliability, failure mode and worst case analysis to determine the optimum approach for the design, and to predict performance of the system for the expected operational and environmental conditions.

Support the development of models that describe the behavior and performance of the actuators and sensors, together with the associated controller, drive, command and telemetry electronics that are required for the analysis and design of the control system. Designs or performs test sequences to measure and characterize the performance of electrical components and systems, and, subsequently, analyzes and interprets the test results and prepares summary reports. Supports requirements definition, review and verification at the mission, instrument, subsystem and component level. Supports all types of reviews throughout program planning and execution.

Senior Electrical Engineer

Interprets system level requirements as they apply to the development of electrical systems and components, identifies design alternatives and performs trade-off studies, error budget, sensitivity, reliability, failure mode and worst case analysis to determine the optimum approach for the design, and to predict performance of the system for the expected operational and environmental conditions.

Support the development of models that describe the behavior and performance of the actuators and sensors, together with the associated controller, drive, command and telemetry electronics that are required for the analysis and design of the control system. Designs or performs test sequences to measure and characterize the performance of electrical components and systems, and, subsequently, analyzes and interprets the test results and prepares summary reports.

Electrical Engineer

(Analog Electronics)

Performs trade-off studies, noise, sensitivity, reliability, failure mode and worst- case performance analysis to design and optimize electronic circuits and systems to meet the functional specifications and perform over the expected range of environmental conditions.

Support the development of models that describe the behavior and performance of the actuators and sensors, together with the sensor signal conditioning, and the actuator drive and control electronics. Designs or performs test sequences to measure and characterize the performance of electronic components and systems, and subsequently analyzes and interprets the test results and prepares summary reports.

Electrical Engineer (Digital Electronics)

Performs hardware and software trade-off studies, timing, reliability, failure mode and worst case analysis to determine and optimize digital electronic circuits and systems to meet the functional specifications and perform over the expected range of environmental conditions.

Support the development of models that describe the behavior and performance of the actuators and sensors, together with the associated command, telemetry and control electronics. Designs or performs test sequences to measure and characterize the performance of electronic components and systems, and subsequently analyzes and interprets the test results and prepares summary reports.

Junior Electrical Engineer

Under the direction of a Senior Electrical Engineer, interprets system level requirements as they apply to the development of electrical systems and components, identifies design alternatives and performs trade-off studies, error budget, sensitivity, reliability, failure mode and worst case analysis to determine the optimum approach for the design, and to predict performance of the system for the expected operational and environmental conditions.

Support the development of models that describe the behavior and performance of the actuators and sensors, together with the associated controller, drive, command and telemetry electronics that are required for the analysis and design of the control system. Designs or performs test sequences to measure and characterize the performance of electrical components and systems, and, subsequently, analyzes and interprets the test results and prepares summary reports.

Senior Electronic

Discusses the layout and assembly problems with electronic engineers and draw sketches to clarify design details and functional criteria of electronic units. Recommends changes in circuitry or installation specifications to simplify assembly and maintenance. Assembles circuitry using engineering instruction, technical manuals, along with knowledge of electronic systems and components and their functions. Sets up-standard test apparatus or conceive test equipment and circuitry, and conduct function, operational, environmental and life test to evaluate the performance and reliability of prototype or production models. Analyzes and interprets test data. Adjusts, calibrates, aligns, and modifies circuitry and components and record unit performance. Wires chassis, harness, consoles, racks, and PC boards from wire lists, schematics, logic diagrams; cuts wire in specified lengths using wire cutters and measuring jig; strips insulation from wire ends using stripping tool; solders wires to specified plugs and terminals; performs layout and fabrication of printed circuit boards.

Electronic

Discusses the layout and assembly problems with electronic engineers and draw sketches to clarify design details and functional criteria of electronic units. Recommends changes in circuitry or installation specifications to simplify assembly and maintenance. Assembles circuitry using engineering instruction, technical manuals, along with knowledge of electronic systems and components and their functions. Sets up-standard test apparatus or conceive test equipment and circuitry, and conduct function, operational, environmental and life test to evaluate the performance and reliability of prototype or production models. Analyzes and interprets test data. Adjusts, calibrates, aligns, and modifies circuitry and components and record unit performance. Wires chassis, harness, consoles, racks, and PC boards from wire lists, schematics, logic diagrams; cuts wire in specified lengths using wire cutters and measuring jig; strips insulation from wire ends using stripping tool; solders wires to specified plugs and terminals; performs layout and fabrication of printed circuit boards.

YOE(5)

Junior Electronics Technician

Discusses the layout and assembly problems with electronic engineers/technicians and draw sketches to clarify design details and functional criteria of electronic units. Assembles circuitry using engineering instruction, technical manuals, and knowledge of electronic systems and components and their functions. Set up-standard test apparatus or conceive test equipment and circuitry, and conduct function, operational, environmental and life test to evaluate the performance and reliability of prototype or production models. Analyzes and interprets test data. Adjusts, calibrates, aligns, and modifies circuitry and components and record unit performance. Wires chassis, harness, consoles, racks, and PC boards from wire lists, schematics, logic diagrams; cuts wire in specified lengths using wire cutters and measuring jig; strips insulation from wire ends using stripping tool; solders wires to specified plugs and terminals; performs layout and fabrication of printed circuit boards.

YOE(1)

Electromechanical Systems Engineer, Subject Matter Expert (SME)

Provides the technical expertise to perform and direct the analysis, design, modeling, simulation and specification of electromechanical systems in response to task requirements. This includes the selection and modeling of actuators and sensors for feedback control systems, the use of classical and modern control techniques in the analysis and design of linear and non-linear feedback systems, an understanding of how to use test data and simulation results to verify system performance, extract model parameters, estimate margins and sensitivities to parameter variations, and predict performance in the disturbance environment of on-orbit operation. Supports requirements definition, review and verification at the mission, instrument, subsystem and component level. Supports all types of reviews throughout program planning and

YOE(15)

Senior Electromechanical Systems Engineer

Provides the technical expertise to perform and direct the analysis, design, modeling, simulation and specification of electromechanical systems in response to task requirements. This includes the selection and modeling of actuators and sensors for feedback control systems, the use of classical and modern control techniques in the analysis and design of linear and non-linear feedback systems, an understanding of how to use test data and simulation results to verify system performance, extract model parameters, estimate margins and sensitivities to parameter variations, and predict performance in the disturbance environment of on-orbit operation.

YOE(10)

Electromechanical Systems Engineer

Provides the technical expertise to perform the analysis, design, modeling, simulation and specification of control systems in response to task requirements. This includes the selection and modeling of actuators and sensors for feedback control systems, the use of classical and modem control techniques in the analysis of linear and nonlinear feedback systems, an understanding of how to use test data and simulation results to verify system performance, extract model parameters, estimate margins and sensitivities to parameter\variations, and predict performance in the disturbance environment of on-orbit operation.

YOE(5)

Thermal Engineer, Subject Matter Expert (SME)

Provides leadership in developing new thermal models in response to task requirements. Supports the development of thermal designs. Analyzes and evaluates temperatures and power requirements to show that specified thermal requirements are satisfied. Provides direction and guidance to lower level Thermal Analysis Engineers. Supports requirements definition, review and verification at the mission, instrument, subsystem and component level. Supports all types of reviews throughout program planning and execution.

Senior Thermal Engineer

Provides leadership in developing new thermal models in response to task requirements. Supports the development of thermal designs. Analyzes and evaluates temperatures and power requirements to show that specified thermal requirements are satisfied. Provides direction and guidance to lower level Thermal Analysis Engineers.

Thermal Engineer Develops new thermal models in response to task requirements. Under the direction of the Senior Thermal Engineer, supports the development of thermal designs. Analyzes and evaluates temperatures and power requirements to show that specified requirements are satisfied. Provides guidance to lower level Thermal Analysis

Junior Thermal Engineer

Under the direction of a Senior Thermal Engineer, supports the development of thermal designs.

Analyzes and evaluates temperatures and power requirements to show that specified requirements are satisfied.

BS

Senior Thermal Development

Engineer

Develops advanced thermal control hardware and software in response to task requirements. Supports advanced thermal control technology development.

Quantifies requirements, develops appropriate design and/or analytical solutions, and conducts tests. Provides guidance and direction to lower level advanced development engineers.

Thermal Development

Engineer

Develops advanced thermal control hardware and software in response to task requirements. Supports advanced thermal control technology development.

Quantifies requirements, develops appropriate design and/or analytical solutions, and conducts tests. Provides guidance and direction to lower level advanced development engineers.

YOE(3)

Contamination

Matter Expert

(SME)

Reviews contamination control requirements, performs detailed contamination analyses, develops contamination control plans, and implements contamination control plans. Develops new analytical tools in response to task requirements.

Provides direction and guidance to lower level Contamination Engineers. Supports requirements definition, review and verification at the mission, instrument, subsystem and component level.

Supports all types of reviews throughout program planning and execution.

BS or equivalent

Senior Contamination

Engineer

Reviews contamination control requirements, performs detailed contamination analyses, develops contamination control plans, and implements contamination control plans.

Develops new analytical tools in response to task requirements. Provides direction and guidance to lower level Contamination Engineers.

Contamination Engineer

Reviews contamination control requirements, performs detailed contamination analyses, develops contamination control plans, and implements contamination control plans. Develops new analytical tools in response to task requirements. Provides direction and guidance to lower level Contamination

Junior Contamination

Engineer

Under the direction of a Senior Contamination Engineer, reviews contamination control requirements, performs detailed environmental analyses of all phases of assembly, integration, test, transportation, pre-launch, on-orbit, and descent, and implements contamination control plans. Operates clean room facilities, performs BRDF light scattering measurements and conducts particulate contamination characterizations.

Senior Thermal Coatings Engineer

Provides thermal coatings expertise in the R&D, application, characterization and qualification of space flight thermal coatings (paints, thin films, tapes, metals, optical surface reflectors, solar cells, polymeric membranes and composites) for aerospace missions. Generate technical documents, test plans, and test reports in reference to these activities.

Evaluates, analyzes, and qualifies the thermal radiative/optical properties of thermal coatings and materials for space flight applications. Performs routine maintenance on government-owned equipment, as needed.

Thermal Coatings

Under the direction of a Senior Thermal Coatings Engineer, performs thermal- optical testing and thermal-radiative testing. Develops and conducts space environmental testing of space flight coatings to evaluate their thermal properties. Evaluates and analyzes the data from reflectance, transmittance, solar absorptance, normal emittance, coating adherence, UV radiation, and thermal cycle testing.

Writes technical reports and test plans. Maintains laboratory records and data. Performs routine maintenance on government-owned equipment, as needed.

BS YOE(3)

Senior Test and Integration

Provides the technical expertise to perform and direct the test and integration of thermal, electronic, and electromechanical systems and subsystems in response to task requirements. This includes the design, fabrication, and operation of ground support equipment (both electronic GSE, and mechanical test fixtures), the design of test sequences, the specification of pass/fail criteria, and the generation of test procedures. This position requires expertise in determining test methodologies, specifying the instrumentation (e.g. accelerometers, thermistors), and test equipment (e.g. DSA's, Laser ranging interferometers) necessary for test, directing the test, and subsequently analyzing the resulting data (statistically, in the time and frequency domain) and preparing summary reports. This requires expertise in operation of various test equipment, and instrumentation sensors, and in the manipulation and processing of resultant data. Tests will often involve measuring system or subsystem performance over temperature, and in the presence of a disturbance environment.

Test and Integration

Provides the technical expertise to perform the test and integration of thermal, electronic, and electromechanical systems and subsystems in response to task requirements. This includes the design, fabrication, and operation of ground support equipment (both electronic GSE, and mechanical test fixtures), the design of test sequences, the specification of pass/ fail criteria, and the generation of test procedures. This position requires expertise in determining test methodologies, specifying the instrumentation (e.g. accelerometers, thermistors), and test equipment (e.g. DSA's, laser ranging interferometers) necessary for test, directing the test, and subsequently analyzing the resulting data (statistically, in the time and frequency domain) and preparing summary reports. This requires expertise in operation of various test equipment, and instrumentation sensors, and in the manipulation and processing of resultant data. Tests will often involve measuring system or subsystem performance over temperature, and in the presence of a disturbance environment.

Senior Test and Integration Technician

Under the direction of Test and Integration Engineer, provides support in the test and integration of thermal, electronic, and electromechanical systems and subsystems in response to task requirements. This includes the breadboarding of test electronics, the fabrication of test harnesses, the interfacing and operation of various test hardware, instrumentation, and equipment, and the documentation of test sequences, and test procedures. It also includes the ability to read and interpret schematics, and efficiently operate computers including the ability to write simple programs.

YOE(10)

Test and Integration Technician

Under the direction of Test and Integration Engineer and/or Senior Test and Integration Technician, provides support in the test and integration of thermal, electronic, and electromechanical systems and subsystems in response to task requirements. This includes the breadboarding of test electronics, the fabrication of test harnesses, the interfacing and operation of various test hardware, instrumentation, and equipment, and the documentation of test sequences, and test procedures. It also includes the ability to read and interpret schematics, and efficiently operate computers including the ability to write simple programs.

YOE(3)

Senior Optical Analyst

Performs and/or directs analysis of electro-optic elements, subsystems, and systems that comprise an optical instrument. Specific duties include system end-to-end studies, digital communication signal to noise analysis, establishing error budgets, etc.

Optical Analyst Under the direction of the Senior Optical Analyst, performs analysis of electro- optic elements, subsystems, and systems that comprise an optical instrument. Specific duties include system end-to-end studies, digital communication signal to noise analysis, establishing error budgets, etc.

Elecctro-Optical Engineer, Subject

Matter Expert

(SME)

Provides the technical expertise to perform or direct the systems analyses in response to task requirements.

Expert in the use of analytical tools or capable of developing new analytical tools: This includes developing interfaces to existing analysis tools such as NASTRAN for interdisciplinary analysis. Knowledge of electro-optical, electronic and mechanical requirements for space flight and special test equipment subsystems, systems, instruments and spacecraft is required. Capable of evaluating and analyzing system requirements and system error budgets to show that they met specific performance requirements. Provide direction and guidance to lower-level systems analysts. Supports requirements definition, review and verification at the mission, instrument, subsystem and component level. Supports all types of reviews throughout program planning and

Senior Electro- Optical Engineer

Performs design, development, calibration, and evaluation of electro-optic elements, subsystems, and systems for spaceflight and ground-based systems.

Included are lasers, detectors, and beam control assemblies.

Electro-Optical Engineer

Performs design, development, calibration, and evaluation of electro-optic elements, subsystems, and systems for spaceflight and ground-based systems.

Included are lasers, detectors, and beam control assemblies.

Cryogenics Engineer, Subject

Matter Expert

(SME)

Conducts or directs research and development work on cryogenic cooling systems for spacecraft systems or instruments. This includes conceiving, designing, and directing the testing of liquid helium, helium-3, adiabatic demagnetization, and dilution refrigerator systems or components. Interface and support the development, fabrication, and testing of components.

Supports requirements definition, review and verification at the mission, instrument, subsystem and component level. Supports all types of reviews throughout program planning and execution.

Senior Cryogenics

Conducts or directs research and development work on cryogenic cooling systems for spacecraft systems or instruments. This includes conceiving, designing, and directing the testing of liquid helium, helium-3, adiabatic demagnetization, and dilution refrigerator systems or components. Interface and support the development, fabrication, and testing of components.

Cryogenics Engineer

Conducts research and development work on cryogenic cooling systems for spacecraft systems or instruments. This includes conceiving, designing, and directing the testing of liquid helium, helium-3, adiabatic demagnetization, and dilution refrigerator systems or components. Interface and support the development, fabrication, and testing of components.

Senior Optical Systems Analyst

Provides the technical expertise to perform or direct the systems analyses in response to task requirements.

Expert in the use of analytical tools or capable of developing new analytical tools: This includes developing interfaces to existing analysis tools such as NASTRAN for interdisciplinary analysis. Knowledge of electro-optical, electronic and mechanical requirements for space flight and special test equipment subsystems, systems, instruments and spacecraft is required. Capable of evaluating and analyzing system requirements and system error budgets to show that they met specific performance requirements. Provide direction and guidance to lower-level systems analysts.

Optical Systems Analyst

Under the direction of the Senior Systems Analyst, performs systems analyses in response to task requirements. Utilizes analytical tools and/or develops new analytical tools. Knowledge of electro-optical, electronic and mechanical requirements for space flight and special test equipment subsystems, systems, instruments and spacecraft is required. Capable of evaluating and analyzing system requirements and system error budgets to show that they met specific performance requirements.

Engineering Analysis Technician

Prepares engineering data for computer analysis using simple hand or computer calculations. Enters data into the computer and recovers the results in the form of plots or summary tables. Compiles reports and documentation from material provided by engineers and designers. Operates drawing and document reproduction equipment.

Metrology

Supports engineers and designers with preparation of engineering data, plots, reports, and other documentation. Prepares engineering data for computer analysis using simple hand or computer calculations. Enters data into the computer and recovers the results in the form of plots or summary tables. Compiles reports and documentation from material provided by engineers and designers.

Operates drawing and document reproduction equipment.

ENCLOSURE CC