09255726 FAA Lynch KY ASAR Radar Site Lead Report.pdf

Audas Environmental Post Office Box 283 Calvert City, KY 42029

Phone: 270-527-5495

LIMITED LEAD INSPECTION REPORT

FOR

FAA ASAR RADAR SITE

LYNCH, KY

PREPARED FOR:

FAA

LYNCH, KY

PREPARED BY:

AUDAS ENVIRONMENTAL

PO BOX 283

CALVERT CITY, KY 42029

PHONE: (270) 527-5495

Project No. 09255726

September 17, 2025

Audas Environmental FAA ASAR Radar Site Lead Inspection Report Lynch, KY

Job # 09255726 09/17/25 ii

TABLE OF CONTENTS

Page

1.0 INTRODUCTION

2.0 INSPECTION METHODOLOGY

3.0 FINDINGS

4.0 RECOMMENDATIONS

5.0 EXCLUSIONS

APPENDICES

Appendix A Laboratory Analytical Report Appendix B Pictures

09/17/25 1

1.0 INTRODUCTION

Audas Environmental, LLC (AE) conducted a limited lead inspection at the FAA ASAR Radar Site, in Lynch, KY. The inspection was conducted on September 10, 2025. The scope of work and the area included in the inspection were given to us by the owner’s representative Ms. Amorette Faires.

2.0 INSPECTION METHODOLOGY

The area was inspected for the presence of Lead (Pb) paint. Paint and soil samples were collected, documented, and photographed. Samples were delivered to SanAir Technologies Laboratory for analysis.

All information contained within this report is based on observations and information gathered at the site.

3.0 LEAD FINDINGS

Paint samples were collected in various locations on and around the tower.

All samples collected were accompanied by a chain of custody and were shipped to an AIHA accredited lab and analyzed via EPA 7000B/3050B protocol.

A total of five (5) paint scrap samples and four (4) soil samples were collected from various locations.

Of these nine (9) samples the five (5) paint samples contained some amount of lead. Content ranged from 3116 µg/g – 100,400 µg/g.

Lead Paint Results Sample No. Location Sample Result

1 Northwest Tower Leg 51090 µg/g

2 Radar stairs - bottom level handrail 100400 µg/g

3 Radar stairs – mid-level handrail 61160 µg/g

4 North center platform South of building 3116 µg/g

5 Radar mid-section cross beam 97660 µg/g

Soil Sample Results Sample No. Location Sample Result

1 Northwest leg <91.1 µg/g

2 Southwest leg <97.5 µg/g

3 Southeast leg <98.9 µg/g

4 Northeast leg <86.3 µg/g

09/17/25 2

4.0 RECOMMENDATIONS

Based on the samples collected, it appears the tower contains lead painted surfaces.

Considering the results from the samples collected from the tower, potential for lead hazard does exist. Any hot work (i.e. cutting, burning, grinding, welding, etc.) on a lead paint surface would be considered a Class III activity by OSHA. Please refer to OSHA Regulation 1926.62 for further direction regarding hot work and other disturbance issues.

Laboratory analytical reports are included in Appendix B.

It should also be noted that lead containing materials other than those identified during the

September 10, 2025 inspection may exist on the subject property. Should suspect materials other than those which were identified during this inspection be uncovered prior to or during the demolition/renovation process, those materials should be assumed lead-containing until sampling and analysis can confirm or deny their lead content.

5.0 EXCLUSIONS

The scope of work for this project included the aforementioned areas sampled. Sample findings represent only the materials directly sampled and are not intended to infer the content of other materials.

09/17/25 3

APPENDIX A

LABORATORY ANALYTICAL REPORT

SanAir ID#: 25061450

Project #: 09255726 Project Name: FAA Radar Report Date: 9/17/2025

Analysis Report prepared for

SanAir ID#: 25061453

Project #: 09255726 Project Name: FAA Radar Report Date: 9/17/2025

Analysis Report prepared for

Dear B. Davis, We at SanAir would like to thank you for the work you recently submitted. The 4 sample(s) were received on Friday, September 12, 2025 via FedEx. The final report(s) is enclosed for the following sample(s): S-01, S-02, S-03, S-04.

These results only pertain to this job and should not be used in the interpretation of any other job. This report is only complete in its entirety. Refer to the listing below of the pages included in a complete final report.

Sincerely, Abisola Kasali Metals Laboratory Director SanAir Technologies Laboratory

Final Report Includes:

- Cover Letter

- Chemistry Analysis

- Disclaimers and Additional Information

Sample conditions:

- 4 samples in Good condition.

10501 Trade Ct., N. Chesterfield, VA 23236 | 804.897.1177 | Fax: 804.897.0070 | www.SanAir.com | LabReports@SanAir.com

09255726Project Number:

P.O. Number:

Project Name: FAA Radar

9/10/2025Collected Date:

9/12/2025 10:10:00 AMReceived Date:

9/17/2025 10:51:13 AM

25061453 SanAir ID Number

FINAL REPORT

Audas EnvironmentalName:

Address: PO Box 283

Calvert City, KY 42029

270-527-5495Phone:

Analyst: Baird, Marti

Test Method: SW846/M3050B/7000B

Lead Soil Analysis µg Pb Sample Calculated Sample

Sample Description In Sample Size Units RL Results Units

25061453 - 1 S-01 / N.W. Leg < 10 0.1098 Grams 91.1 <91.1 µg/g 25061453 - 2 S-02 / S.W Leg < 10 0.1026 Grams 97.5 <97.5 µg/g 25061453 - 3 S-03 / S.E Leg < 10 0.1011 Grams 98.9 <98.9 µg/g 25061453 - 4 S-04 / N.E Leg < 10 0.1159 Grams 86.3 <86.3 µg/g Method Reporting Limit < 10 µg/0.1 g soil. NOTE: µg/g=ppm

Signature:

Date: 9/16/2025 Date: 9/16/2025

Reviewed:

10501 Trade Ct., N. Chesterfield, VA 23236 | 804.897.1177 | Fax: 804.897.0070 | www.SanAir.com | LabReports@SanAir.com

09255726Project Number:

P.O. Number:

Project Name: FAA Radar

9/10/2025Collected Date:

9/12/2025 10:10:00 AMReceived Date:

9/17/2025 10:51:13 AM

25061453 SanAir ID Number

FINAL REPORT

Audas EnvironmentalName:

Address: PO Box 283

Calvert City, KY 42029

Disclaimer

This report is the sole property of the client account named on the chain-of-custody (COC) submitted to SanAir Technologies Laboratory, Inc. (SanAir). Results in the report are confidential information intended only for the use by the customer listed on the chain of custody. Neither results nor reports will be discussed with or released to any third party without our client’s written permission. Final reports cannot be reproduced, except in full, without written approval from SanAir to assure that parts of the report are not taken out of context. This report and any information contained within shall not be edited, altered, or modified in any way by any persons or agencies receiving, viewing, distributing, or otherwise possessing a copy of this final report. The laboratory reserves the right to perform amendments to any finalized report, of which shall supersede and make obsolete any previous editions. Such changes, modifications, additions, or deletions shall be effective immediately upon notice thereof, which may be given by means including but not limited to posting on the SanAir client portal website, electronic or conventional mail, or by any other means.

The information provided in this report applies only to the samples submitted and is relevant only for the date, time, and location of sampling. The accuracy of the results of the analysis is dependent upon the method of sample procurement and information provided by the client on the COC. SanAir is not responsible for the method of sample procurement. SanAir assumes no responsibility for information provided by the client on the COC such as project number, project name, collection dates and times, po number, special instructions, samples collected by, sample numbers, sample identifications, sample type, selected analysis type, flow rate, total volume or area, and start stop times that may affect the validity of the results in this report. SanAir Technologies Laboratory, Inc only assures the precision and accuracy of the data it generates and assumes no responsibility for errors or biasing that occur during collection prior to SanAir’s receipt of the sample(s). Evaluation reports are based solely on the sample(s) in the condition in which they arrived at the laboratory and on the information provided by the client on the COC. Sample(s) were received in good condition unless otherwise noted on the report. All quality control results are acceptable unless otherwise noted. SanAir does not make contamination corrections to reports based upon analysis of laboratory and/or field blanks. When the client requires samples to be tested that deviate from a specific method or condition, all reported results may be affected by the deviation. SanAir assumes no responsibility or liability for the manner in which the results are used or interpreted. SanAir’s Method Detection Limits (MDL) and Reporting Limits (RL) have been derived using various materials meeting each accrediting agencies’ standards. All samples are disposed of after 60 days unless otherwise requested by the client. For Lead Exposure Limits in Soil, refer to HUD Guidelines for the Evaluation and Control of Lead- Based Paint Hazards and State and Federal Regulations, where applicable.

SanAir Technologies Laboratory, Inc. participates in the Environmental Lead Accreditation Program (ELAP) administered by AIHA LAP, LLC (Laboratory ID LAP-162952) and has met the EPA's NLLAP program standards. SanAir also participates in the State of New York’s DOH-ELAP program (NY Lab Id No. 11983) and the Commonwealth of Virginia Division of Consolidated laboratory Services program (VELAP ID#460251). This report does not constitute nor shall be used by the client to claim product, process, system, or person certification, approval, or endorsement by AIHA LAP, LLC, NELAC, NIST, and/or any other U.S. governmental agencies; all or some test results contained in this report may not be accredited by every local, state or federal regulatory agency. Refer to the SanAir website at www.sanair.com for copies of current certificates and scopes of various accreditations, certifications, and licenses or contact the laboratory for inquiries regarding the status or scope of an accreditation or certification.

AIHA LAP, LLC Lab ID: LAP-162952 Commonwealth of VA Department of General Services DCLS, VELAP Laboratory ID#460251 New York State Department of Health Laboratory ID No: 11983 State of Connecticut Department of Public Health Environmental Laboratory Registration Number: PH-0105 Ohio Department of Health Environmental Lead Laboratory Approval Number E10049 State of Rhode Island Department of Health Environmental Lead Laboratory No LAO00371

Revision Date 3/24/2025

Dear B. Davis, We at SanAir would like to thank you for the work you recently submitted. The 5 sample(s) were received on Friday, September 12, 2025 via FedEx. The final report(s) is enclosed for the following sample(s): P-01, P-02, P-03, P-04, P-05.

These results only pertain to this job and should not be used in the interpretation of any other job. This report is only complete in its entirety. Refer to the listing below of the pages included in a complete final report.

Sincerely, Abisola Kasali Metals Laboratory Director SanAir Technologies Laboratory

Final Report Includes:

- Cover Letter

- Chemistry Analysis

- Disclaimers and Additional Information

Sample conditions:

- 5 samples in Good condition.

10501 Trade Ct., N. Chesterfield, VA 23236 | 804.897.1177 | Fax: 804.897.0070 | www.SanAir.com | LabReports@SanAir.com

09255726Project Number:

P.O. Number:

Project Name: FAA Radar

9/10/2025Collected Date:

9/12/2025 10:10:00 AMReceived Date:

9/17/2025 10:50:36 AM

25061450 SanAir ID Number

FINAL REPORT

Audas EnvironmentalName:

Address: PO Box 283

Calvert City, KY 42029

Analyst: Douglass, Vincent

Test Method: SW846/M3050B/7000B

Lead Paint Analysis PAINT µg Pb Sample Size Calculated Sample Sample

Sample Description In Sample (grams) RL Results Results

25061450 - 1 P-01 5247 0.1027 97.4 51090 5.109 % N.W Tower Leg µg/g (ppm) By Weight

25061450 - 2 P-02 10240 0.102 98 100400 10.040 % Radar Stairs Bottom Level Handrail µg/g (ppm) By Weight

25061450 - 3 P-03 6880 0.1125 88.9 61160 6.116 % Radar Stairs Mid-Level Handrail µg/g (ppm) By Weight

25061450 - 4 P-04 313 0.1004 99.6 3116 0.312 % N. Center Platform S. Of Bldg µg/g (ppm) By Weight

25061450 - 5 P-05 10680 0.1093 91.5 97660 9.766 % Radar Mid Section Cross Beam µg/g (ppm) By Weight

Method Reporting Limit <10 µg/0.1 g paint

Signature:

Date: 9/16/2025 Date: 9/16/2025

Reviewed:

10501 Trade Ct., N. Chesterfield, VA 23236 | 804.897.1177 | Fax: 804.897.0070 | www.SanAir.com | LabReports@SanAir.com

09255726Project Number:

P.O. Number:

Project Name: FAA Radar

9/10/2025Collected Date:

9/12/2025 10:10:00 AMReceived Date:

9/17/2025 10:50:36 AM

25061450 SanAir ID Number

FINAL REPORT

Audas EnvironmentalName:

Address: PO Box 283

Calvert City, KY 42029

Disclaimer

This report is the sole property of the client account named on the chain-of-custody (COC) submitted to SanAir Technologies Laboratory, Inc. (SanAir). Results in the report are confidential information intended only for the use by the customer listed on the chain of custody. Neither results nor reports will be discussed with or released to any third party without our client’s written permission. Final reports cannot be reproduced, except in full, without written approval from SanAir to assure that parts of the report are not taken out of context. This report and any information contained within shall not be edited, altered, or modified in any way by any persons or agencies receiving, viewing, distributing, or otherwise possessing a copy of this final report. The laboratory reserves the right to perform amendments to any finalized report, of which shall supersede and make obsolete any previous editions. Such changes, modifications, additions, or deletions shall be effective immediately upon notice thereof, which may be given by means including but not limited to posting on the SanAir client portal website, electronic or conventional mail, or by any other means.

The information provided in this report applies only to the samples submitted and is relevant only for the date, time, and location of sampling. The accuracy of the results of the analysis is dependent upon the method of sample procurement and information provided by the client on the COC. SanAir is not responsible for the method of sample procurement. SanAir assumes no responsibility for information provided by the client on the COC such as project number, project name, collection dates, po number, special instructions, samples collected by, sample numbers, sample identifications, sample type, selected analysis type, flow rate, total volume or area, and start stop times that may affect the validity of the results in this report.

SanAir only assures the precision and accuracy of the data it generates and assumes no responsibility for errors or biasing that occur during collection prior to SanAir’s receipt of the sample(s). Evaluation reports are based solely on the sample(s) in the condition in which they are received at the laboratory and on the information provided by the client on the COC. Sample(s) were received in good condition unless otherwise noted on the report. All quality control results are acceptable unless otherwise noted. SanAir does not make contamination corrections to reports based upon analysis of laboratory and/or field blanks. When the client requires samples to be tested that deviate from a specific method or condition, all reported results may be affected by the deviation. SanAir assumes no responsibility or liability for the manner in which the results are used or interpreted. SanAir’s Method Detection Limits (MDL) and Reporting Limits (RL) have been derived using various materials meeting each accrediting agencies’ standards. All samples are disposed of after 60 days unless otherwise requested by the client. For Lead Exposure Limits, refer to HUD Guidelines for the Evaluation and Control of Lead-Based Paint Hazards and State and Federal Regulations, where applicable.

SanAir Technologies Laboratory, Inc. participates in the Environmental Lead Accreditation Program (ELAP) administered by AIHA LAP, LLC (Laboratory ID LAP-162952), and has met the EPA's NLLAP program standards. SanAir also participates in the State of New York’s DOH-ELAP program (NY Lab Id No. 11983) for lead in paint. This report does not constitute nor shall be used by the client to claim product, process, system, or person certification, approval, or endorsement by AIHA LAP, LLC, NELAC, NIST, and/or any other U.S. governmental agencies. All or some test results contained in this report may not be accredited by every local, state or federal regulatory agency. Refer to the SanAir website at www.sanair.com for copies of current certificates and scopes of various accreditations, certifications, and licenses or contact the laboratory for inquiries regarding the status or scope of an accreditation or certification.

AIHA LAP, LLC Lab ID: LAP-162952 New York State Department of Health Laboratory ID No: 11983 State of Connecticut Department of Public Health Environmental Laboratory Registration Number: PH-0105 Ohio Department of Health Environmental Lead Laboratory Approval Number E10049 State of Rhode Island Department of Health Environmental Lead Laboratory No LAO00371

Revision Date 3/24/2025

09/17/25 4

APPENDIX B

PICTURES