DWG 2200256-A.pdf

CAGE CODE 0WY55 DWG NO. 2200256 SHEET 1 OF 3

APPLICATION

NHA USED ON LTR DATE ECO ECP REVISION DESCRIPTION APVD

WSR-88D A 070105 ECP 0232

ECO A03040 INITIAL RELEASE CWF

VENDOR ITEM CONTROL DRAWING

DISTRIBUTION STATEMENT A: APPROVED FOR PUBLIC RELEASE; DISTRIBUTION IS UNLIMITED.

UNLESS OTHERWISE SPECIFIED

DIMENSIONS ARE IN INCHES

TOLERANCES ON:

WSR-88D RADAR OPERATIONS CENTER

3200 MARSHALL AVENUE

NORMAN, OKLAHOMA 73072-8032

NOMENCLATURE

MILLIMETERS

1 PL ±

2 PL ±

ANGLES ± 2°

INCHES

2 PL ±

3 PL ±

APPROVALS

DWN JCK 070105 RMT JWG 070112

CHK AWB 070112 DOC ARC 070112

ENGR CWF 070112 CM

QA ROC CMJ 070112

HOOD, METAL, 50 POS, D-SUB

SIZE CAGE CODE DWG NO. REV

A 0WY55 2200256 A

SCALE: NONE SHEET 1 OF 3

CAGE CODE 0WY55 DWG NO. 2200256 SHEET 2 OF 3

GENERAL NOTES:

1. INTERPRET THIS DRAWING IN ACCORDANCE WITH ASME Y14.100.

1.1. IDENTIFICATION OF ANY SUGGESTED SOURCE OF SUPPLY (MANUFACTURER) CONTAINED IN THIS

SPECIFICATION IS NOT TO BE CONSTRUED AS A GUARANTEE OF PRESENT OR FUTURE AVAILABILITY

AS A SOURCE OF SUPPLY FOR THE ITEM(S).

1.2. THE USE OF A DIFFERENT PART FROM A LISTED SUGGESTED SOURCE OF SUPPLY OR A PART FROM A

NON-LISTED SUGGESTED SOURCE OF SUPPLY WHICH MEETS THE SPECIFICATIONS HEREIN SHALL OCCUR ONLY AFTER REVIEW/CONCURRENCE AND A FIRST ARTICLE QUALIFICATION BY THE WSR- 88D RADAR OPERATIONS CENTER (ROC) AS WELL AS ACCEPTANCE INSPECTION BY THE NATIONAL

RECONDITIONING CENTER (NRC).

2. REQUIREMENTS:

2.1. STYLE: EMI SHIELDING METAL HOOD

2.2. POSITIONS: FOR 50-POSITION CONNECTORS.

2.3. TYPE: TWO-PIECE SNAP-ON METAL HOODS WITH BOLT FASTENERS.

2.4. HOOD MUST HAVE EMI/RFI SHIELDING.

2.5. HOOD MUST BE INSULATED.

2.6. MATERIAL: METAL WITH NO LEAD CONTENT.

2.7. WIRE DIAMETER: ACCEPTS CABLE UP TO .72 IN DIAMETER.

2.8. STRAIN RELIEF: HOOD MUST HAVE STRAIN RELIEF TO ACCOMMODATE CABLING AS SMALL AS .63 IN

DIAMETER.

2.9. INCLUDES JACKSCREW AND SADDLE.

2.10. PART IDENTIFICATION:

2.10.1. VENDOR IDENTIFICATION AND VENDOR PART NUMBER TO BE APPLIED BY VENDOR.

3. PROCURING AGENCY:

3.1.1. THE PROCUREMENT AGENCY RESERVES THE RIGHT TO PERFORM ANY INSPECTION DEEMED

NECESSARY TO BE ASSURED THE PARTS CONFORM TO THE SPECIFIED REQUIREMENTS.

4. THE PART NUMBER IS THE DRAWING NUMBER SUFFIXED WITH THE APPLICABLE DASH NUMBER

SHOWN IN TABLE II.

SCALE: NONE SHEET 2 OF 3

CAGE CODE 0WY55 DWG NO. 2200256 SHEET 3 OF 3

5. SUGGESTED SOURCE(S) OF SUPPLY (MANUFACTURER(S)):

JIC INDUSTRIAL, INC. (CAGE CODE 1JQ29)

MILPITAS, CA 95035

PART NO.: PER TABLE I

TABLE I

DASH

NO. JIC PART NUMBER

201 HD-50MTL-VG-R TYPE 3

6. FIGURES AND DIAGRAMS

FIGURE 1

DIMENSIONS IN INCHES

SCALE: NONE SHEET 3 OF 3