5.3_Reference_2_EML500_General_Specification_GS_80B80M01E_13th_Ed.pdf

EML500 series General Specifications

GS 80880M01E 13th

EML500

Electromagnetic Log

General The EML500 series electromagnetic log confirms to the technical requirements for the performance standard determined by IMO Resolution A824(19) and MSC.96(72) also meet type approval issued by the Transport Ministry of JG

Certificate number of type approval

- JG : No. 3795

- MED (Wheel mark) : MED-B-6816

Features

1) Small size and light weight compared ordinary models.

2) The length of cable between the sensor and the master unit can be extended maximum 300m by adoption of the preamplifier built.

3) Full provision of various external interfaces

- Pulse output (Photo coupler / contact)

- Digital signal (NMEA0183)

- Analog signal (OV to 5V DC / DA to 20mA)

- Alarm contact output and Digital 1/F form GPS

4) Reduction in the number of parts by employment of highly integrated circuits including microprocessor, and has no moving parts, thereby achieving high reliability.

5) Provision of small size and light weight master indicator for indication of speed and distance, and can be operated by the master indicator. Milepost calibration etc., thereby, installation place of master indicator is not limited.

6) Variety of sensors available to meet various instillation requirements. A dual-axis sensor can measure not only the longitudinal, speed but also the transverse speed.

7) Built-in self-diagnostic function.

8) All indicators can be driven by input signal (NMEA0183) from

GPS.

General specification

- Measurement subject : Ship's water speed and distance

- Measurement principle : Faraday's law of electromagnetic induction

Performance specification

- Measurement range

Speed -4kt to +20kt (Note 1

-5kt to +25kt (Note 1

-7kt to +35kt

-10kt to +50kt (Note 2

(Note 1 MED is attended in case of Single-axis system (range of "-4kn to 20kn" or "-5kn to 25kn").

(Note 2 Additional engineering is required concerning the installation of the sensor.

Trance verse speed : 0kt to ±6.5kt (for Dual-axis)

Distance : 0nm to 9999.99nm

YOKOGAWA+

Yokogawa Denshikiki Co., Ltd.

- Single-axis sensor (right)

- Dual-axis sensor (right)

- MHR130/LR525 Speed indicator

- LR523 Master indicator (left)

- L T501 Master unit (left)

Dictation of ship movement: 0 to 359 deg., clockwise from the bow-to-stern line (fixed to O deg. if the resultant speed is 0.5kt or less)

- Measuring accuracy

Speed - Measurement accuracy

2% of the speed of the ship, or 0.2 knots, whichever is greater.

- Indicate accuracy

±0.15kt with respect to standard signal input

(±0.25kt or less if the measuring range is above 50kt)

Distance ±0.2nm/h or ±2.0% max., whichever is larger

Direction of ship direction : ±2.5 deg. max.

- Response speed

Variable up to 2min for a O to FS-step input (0% to 90% response)

- Restriction of the cables between each equipments

N N N 0 N N N

> " " " L 1 = 200m Max.

L2 = 200m Max.

a: a: a:

L3 = 250m Max.

Junct ion box

Note) The cable specification with Cross specification : 0.5mm2

Resist ance : 30Q/km

2013.04 13th (YDK) 2004.11 2006.04 2009.09

L4 = 50m Max.

Maker supply cable

10th (YDK) 11th(YDK) 12th(YDK)

GS 80BBOM01 E

2002.12 7th (YDK)

2004.05 Bth (YDK)

2004.10 9th (YDK)

Environmental conditions

- Ambient temperature : operating -15°C to +55°C

- Humidity

-Vibration not operating -20°C to +6D°C

95% RH (no dew condensation around)

5Hz to 12.5Hz ±1.6mm

12.5Hz to 25Hz ±0.38mm

25Hz to 50Hz ±0.1mm

-EMC:Acc.to IEC 60945

System configuration diagram

- Noise of power source line :

Not failure in the state put on the pulse 100/400nsec, 1500V during three minutes.

- Insulation resistance :

At last 1 DO using a 500V megger (Excluding electronic circuit)

- Withstanding voltage

1500V AC for 1 min. (Excluding electronic circuit)

Analog speed indicator Assist Monitor

(MHR112)

(Option)

Universal data display

(MHR120)

(Option)

Master indicator

(LR523)

(MHR130) (LR525)

i)o,<i lleHL: : 1~1 ·::~~.

Ship's Speed

(NMEA0183)

~S J>------1 .. ~I

Ship' s power supply 100V to 115V AC or 200V to 230V AC

Serial signal (YDK format:)

I t Dimmer box

(MKD010)

Serial s ignal (NMEA0183 format)

Analog signal (Voltage signal) : 4 circuit (OV to 5V DC or 1V to 5V DC) _.

Analog signal (Current signal) : 2 c ircuit (QA to 20mA or 4 to 20mA) ~

Pulse signal (contact signal) t J

Dimme r box

(LD001A)

VDR

ECDIS

I

_1_

:1···

I Dimmer box

(MKDD02)

l

Junction box

(LN052)

_(_2o_o_pl_n_m) _________ __..,_I RADAR etc.

m w

EML500-HD1 (Single-axis)

Cll 35F Double-bottom type

Pulse signal (Photo coupler ) (200p/ nm)

EML500-HS1 (Sigle-axis)

Cll 35F Single-bottom type

Sea wat er valve , / (LVOJJ) +-k Sea water valve

/ (LV033)

Cll 35 sensor Cj) 35 sensor

(LS501 ) (LS531)

Rodmeter

(LS591)

Yokogawa Denshikiki Co.,Ltd.

ARPA

GYRO COMPASS

AUTO PILOT

INS

RADAR

True wind direct ion and speed indicat or

EML50 HV1/HV2

(Single / Dual axis)

Cll 70F Single-bottom type

Sea water valve

(LV071A)

Cll70 sensor

EML500-FA1/FA2

(Single / dual axis)

Cll48F Single-bottom type

Sea water valve

(LV052)

Cll48 sensor

(LS571 : Single axis) (LS572 : Dual axis)

(LS541 : Single sxis) (LS542 : Dual axis)

GS80B80M01 E 13th 2013-04

Component models of EML500 EML500 is composed of Master unit, Master indicator and Sea-bottom (with sensor).

And if it is necessary, combined with speed indicator and environ equipments.

Basic system models According to type of Sensor unit, basic system model is set.

Component Models : EML500-DDD

... I __ ""')"" Sensor unit code

~e

EML500-DDD

Pr HS1 HD1 HV1 FA1 HV2 FA2

Master unit LT501 0 0 0 0 0 0

Master indicator LR523 0 0 0 0 0 0

Speed indicator (Single-axis) MHR130 0 0 0 0

Dimmer box MRD010 0 0 0 0

Speed indicator (Dual-axis) LR525 0 0

Dimmer box LD001A 0 0

Junction box LN052 0 0 0 0 0 0

LS531 0

LS501 0

LS571 0

Sensor

LS541 0

LS572 0

LS542 0

Rodmeter LS591 0

Sensor cable LS503 0 0 0 0 0

LV033 0 0

Seawater valve LV071A 0 0 ., LV052 0 0 ·c:

Seawater valve flange LV904 0 ...

"' Protection tube LV905 0 C:

" en Mounting LV902A-1 D !::,.

plate for LV902A-20 !::,.

seawater LV902A-3D !::,.

valve LV902A-40 !::,. !::,.

LV902A-5 0 !::,. !::,.

LV910 !::,. !::,.

LV901-1 D !::,.

LV901-20 t:,.

Zinc plate

LV901-3 0

(Note) (Note)

Installation Single- Double- Single- Single- Single- Single-

Sensor type bottom bottom bottom bottom bottom bottom

Standard length 7mm 13mm 7mm 13mm installation 50mm 50mm or or or or of protrusion 57mm 73mm 57mm 73mm iili ~

MRD010/ MRDOl 1

LD001A/ LD002

<!> 35sensor with cable

Only sensor element <!> 35

<!> 70 sensor (Single-axis)

<!> 48 sensor (Single-axis)

<!> 70 sensor (Dual-axis)

<!> 48 sensor (Dual-axis)

Not including the sensor

For sensors <!> 35

For sensors <!> 70

For sensors <!>48

Note: For Flash-mounted unit (Unnecessary for a protruding unit)

Length from bottom plate

Note : Items marked with a " I::,. " are ordered from the shipbuilder as standard.

Yokogawa Denshikiki Co.,Ltd. GS80B80M01 E 13th 2013-04

Engineering specification

- Power

1 DOV to 115V AC or

200V to 230VAC ±10% 50/60Hz ±6%

(Selectable by the jumper setting in the power supply unit)

- Power consumption

BOVA

- Input signal

- Input the detected voltage at sensor

0.242mA/knot (from sensor)

- Input from GPS (for back-up by GPS)

Data foimat of GPS input can be set by Master indicator.

Connection units : GPS, Other speed sensor

Transmission format: Asynchronous serial data signal

Transmission rate : 4800bps

Data character Start bit 1 bit

Data bit 8 bit

Stop bit 1 bit

Parity None

Data foimat

Recommend format : based on IEC61162-1, VTG, VBW, VHW and etc ...

Header character : 6 ASCII letter

(Example : $GPVTG and etc ... )

Position of speed data:

Set data based on the location of commas.

Checksum

Input circuit

- Output signal

: Select Use or Unused

: Photo coupler

- Analog speed signal : Voltage output (2 circuit)

Output level : Select able from OV to 5V or 1 V to 5V

Output volU!ge Output cu rrent

5V --------------- 5V --------------

1V

-~O,-kt "',a O~V-----~,"~II k,-t ~= SVShip' s speed -~o,"""'t •C.,l,....V ----.=,"=n k~t .~ SY Ship' s speed

Output voltage Output current

SY -------------- 5V --------------

1V Ship' s speed I Ship' s speed

- Ful"°lkt"""•~OV.,+------~,,~,, ,,...., ~= 5V - Fu1·1°" , ,- . ~, v.,+-----.=,,~11,....,,~= 5V

Yokogawa Denshikiki Co.,Ltd.

- Analog speed signal : Current output (4 circuit)

Output level : select able from OmA to 20mA or 4mA to 20mA

Out.put voltage Output current

20mA --------------- 20mA ---------------

4mA

S hip' s speed S hip' s s peed -=Ok-t a"',O-mA~---.~,"~11 k-'-t a~,OmA -=,,-, a'-,4m~A----+~Fu~ll k-'-t a~2~0mA

Output voltage Output current

20mA ---------------

- Distance pulse output : Photo coupler type (8 circuit)

Capacity Voltage between terminals 24V max

Sh ink current 5mA max.

Dark current 50µA max.

(at 24V between terminals)

Pulse weight 200P/nm

- Distance pulse output: Relay contact type (2 circuit)

Capacity Rate loads 30V DC, 1A

(resistance load) 30V AC, 0.5A

Minimum appliciate load 1 OmV DC, 1 OµA

Chattering

Pulse weight

1msecmax.

200P/nm

- Serial signal output

Serial signal : based on NMEA0183 (Ver.2.3)

Transmission format : Asynchronous serial data signal

Transmission rate : 4800bps

Transmission period : 1sec

Transmission length : 1.2km

Data character Start bit 1 bit

Data bit 8 bit

Stop bit 1 bit

Parity None

Connected Device : RADAR, ECDIS and etc ..

Output circuit : EIA RS-422-A

SN75172 t')SHILD

- Data format (based on NMEA0183)

( EM.Log Software version : "P" )

Output sentence is possible changing by DIP SW.

<NMEA Ver 2.0 setting : Normally setting>

VBW sentence

11$1TvlM!TvlslwlToAoA If'""' ; '""'I~;::-~':';:

'----------Checksum identifier

'----------Data ~-----------Talker identifier VBW : Dual ground / water speed

~-------------Talker identifier : VM EM LOG

~--------------Header

Data block format

1) for single-axis

I, IY- IJO'IIO'l · l10 ·l10 'I, I, I a I , I , I, 1v1 y y

Longitudinal A:data valid V:Data invalid water speed (kt) V:data invalid Fixed data

2) for dual-axis

I , IY-110'1 1001 · !io-•!io-'! · IY-l10·lwl . !io-•!io-'! , I a I , I , I , IV I y y

Longitudinal Transverse A:data valid V:Oat a invalid wate r speed (kt) water speed (kt) V:data invalid Fixed data

3) When the GPS speed is selected

I , IY- IJO'l 100l -lrn-'l10-'I , I , I a I, IO l10·l100l -l10-·110-1 , 1.1 a I y y

Longitudinal A:dat a valid Longit udinal V:Data invalid water speed (kt ) V:data invalid ground speed (kt) Fixed data

4) When the system error is detected

1-1-1 -lvl . 1. I -!vi

5) When the ROM/RAM error is detected

Sentence is not output.

-AN : A= Data valid

V = Data invalid

- Range of data

Water speed : -13.00kt to 65kt

Ground speed : 0.00kt to 99.9kt

VHW sentence

11$1Tv!M!Tv!H!w!TDATA If suM1 I suM2 I~~~~:::::

'----------Check sum identif ier

'----------Data '------------Talker identifier VHW: Water speed and heading

~-------------Talker identifier: VM EM LOG

~--------------Header

Data block format

1) When the Log speed select (single axis and dual axis)

1-1 · 1 · 1. 1. l.10'1 1001 : l10-·l10-j . I~) . 1- lj Water Speed K (k ) km/ h

(kt) not s t

2) When the GPS speed select

1. 1.1 . 1 .1 , 110'1 1001 -l10 'l101 . 1 NI .1 .1 KI y y

Ground Spee d K t (kt) km/ h

(kt) no s

3) When the system error is detected

1.1.1 . 1.1 . 1. !NI .1.1K1

Yokogawa Denshikiki Co.,Ltd.

4) When the ROM/RAM error is detected

Sentence is not output.

- Range of data

Water speed : 0.00kt to 65kt

O.OOkm/h to 120.38km/h

VLW sentence

~---------Checksum ident ifier

11$1TvlMITvlLlwlToAoA If'""' I'""' I~;;:;::;

~---------Data

~-----------Talker identifier VLW : Distance traveled through the water

~-------------Talker ident ifier: VM EM LOG

~--------------Header

Data block format

1) at normal operation

I , l.103!1021101110°1.110+1 . IN I , l.10'!102!101 !1001.1w-•l1 0-j ' IN I . ..

Total cumulative distance (nm) Distanc e s ince rest (nm)

2) When the system error is detected

I, I, INI ' I, INI

3) When the ROM/RAM error is detected

Sentence is not output.

- Range of data

Total cumulative distance : 0.00nm to 9999.99nm

Distance since rest : 0.00nm to 9999.99nm

- Checksum

Checksum is the 8-bit exclusive-OR (no start or stop bits) of all characters in the sentence, including "," delimiters, but not including the "$" and the "*" delimiters.

<NMEA Ver 2.3 setting>

VBW sentence

11$1Tv1M1Tv1B1w1TDA,A Ir·· I'""' I~:.-:-.-::

'----------Check sum identifier

'----------Data ~-----------Talker identifier VBW Dual ground / water speed

~-------------Talker identifier : VM EM LOG

~--------------Header

Data block format

1 ) for single-axis

I , 17-110'1•00! . 1,0-,lwj . 1-I~) .. 1. 1-1:;) . I . 1:;1 . 1- 1:;1 Longitudinal A:data vahd V:Data invalid water speed (kt ) V:data invalid Fixed data

2) for dual-axis

I -l'.!-"l•0·l·00! · l10 ·l10 j . l'.!-"l 10·l•00!. f0 ·l10 j -I~ . I -I -!VI .1.1v1 -I -!VI Longitudinal Transverse A:da~alid y y y V:Data invalid water speed (kt) water speed(kt) V:dat a invalid Fixed data

3) When the GPS speed is selected (single-axis)

1-M0·l·00!, 110-'lwj -I -lc:,1-1 ° l'°'I'""!, lw'l10·j -1 -lj , I, 1v1 , I, 1v1 Longitudinal A:data valid Longitudinal A:data valid y y V:Dat a invalid wat er speed (kt) V:data invalid ground speed (kt) V:data invalid Fixed data

4) When the GPS speed is selected (dual-axis)

4) When the ROM/RAM error is detected

Sentence is not output.

- Range of data

Water speed : 0.00kt to 65kt

O.OOkm/h to 120.38km/h

Ground speed : 0.00kt to 99.90kt

O.OOkm/h to 185.01km/h

VLW sentence

- Check sum identif ier

$ ITvlMITvlLlwlToA" If"'"' I"'"' I~;;:::~;

'----------Data

'--------------Talker identifier VLW: Distance traveled through t he water

'--------------Talker ident if ier: VM EM LOG

~--------------Header

Data block format

1) at normal operation

, 10' 102 101 100 • 10-110 , N , 10' 102 101 100 • 10-1 10- , N

Total cumulative distance (nm) Distance since rest (nm)

2) When the system error is detected I, l~l"'I"'! l10 l10 j ' l~H·if! H10 I, l•I, 1° 110'110 !, fa H, I,~ . I, 1v1, I, 1v1 l ongitudinal Transverse A:da~ valid Longitudinal A:da~alid ~ V:Data invalid I - 1. 1. 1. I water speed (kt ) wat er speed(kt ) V:data invalid ground speed(kt) V:data invalid Fixed data

5) When the system error is detected

I, I, I, 1v1 . I, I, 1v1. I, 1v1 . I, 1v1

6) When the ROM/RAM error is detected

Sentence is not output.

-AN : A= Data valid

V = Data invalid

- Range of data

Water speed : -13.00kt to 65kt

Ground speed : 0.00kt to 99.9kt

VHW sentence

$ ITvlM ITv !H!W!TDA;> If '""' I '""' I~ ;~~::':

- Check sum ident ifier

'------------Data

'--------------Talker identifier VHW: Wat er speed and heading

~-------------Talker identifier : VM EM LOG

~--------------Header

Data block format

1) When the Log speed is selected

I , I , I, I , I , l10'l100l · l10 'l10 'I , IN I , l102l101l100l -l10 ·l10 1, I KI y y

Water Speed K (k ) Water Speed

(kt) nots t (km/ h) km/ h

2) When the GPS speed is selected

I , I, I, I , I , l10'l 100I · l• 0-·l10·1 , IN I , l10'110'l 100I · l10··l10·1, I KI y y

Ground Speed K (k ) Ground Speed

(kt) nots t (kt) km/ h

3) When the system error is detected

I -I, I, 1. I -I- I -I -I

Yokogawa Denshikiki Co.,Ltd.

3) When the ROM/RAM error is detected

Sentence is not output.

- Range of data

Total cumulative distance : 0.00nm to 9999.99nm

Distance since rest : 0.00nm to 9999.99nm

- Checksum

Checksum is the 8-bit exclusive-OR (no start or stop bits) of all characters in the sentence, including"," delimiters, but not including the "$" and the "*" delimiters.

- Speed limit output (2 circuits)

Contact : At state of speed limit "Close" (standard)

At state of speed limit "Open"

(Selectable by Dip.SW 9-2(off: close, on: open))

Capacity Rate loads 30V DC, 1A

Setting

(resistance load) 30VAC, 0.5A

Minimum appliciate load 1 OmV DC, 1 OµA

Chattering 1 msec max.

: The higher or lower speed limit can be set by

Master indicator.

-Alarm contact output (2 circuits)

Contact : At abnormal "Close" (standard)

At abnormal "Open"

(Selectable by Dip.SW 9-3(off: close, on: open))

Capacity Rate loads 30V DC, 1A

(resistance load) 30VAC, 0.5A

Minimum appliciate load 1 OmV DC, 1 OµA

Chattering 1msecmax.

Failure alarm - ROM/RAM error

- Low battery (less than 2.1V)

- AID converter error

- GPS input error

- Communication error between Master unit and Master indicator.

Comportment equipment specification

- Master unit LT501

Receives and converters speed data signals from the sensor. Then transmits the speed and distance to external devices in various signal forms.

- Wiring position : Coaming of under or back

- Installation : Wall or flush mounted type

- Master indicator LR523

Receives digital signals from the master unit, and displays the speed and distance. Both the display and operation panel are on the front of the master indicator. Set data are sent to the master unit in the form of digital signals, and placed in the memory.

- Display function

The speed and distance are displayed with digital by LED indicator.

1) Indicate of the Speed and Distance

Speed : (-)CD Ckt

Distance : ITIIJ Dim

2) Indicate of the trip distance

Trip distance : ITIIJ Dim

3) Indication of the longitudinal transverse speed

(for dual-axis) longitudinal speed : (-)CD Ckt

Transverse speed : S/PD Ckt

4) Indicating of the resultant speed and detection

(for dual-axis)

Resultant speed : (-)CD Ckt

Direction : ITil:leg (relative direction)

5) Indication of GPS speed data

It is indicated ship's speed, total distance traveled and trip distance by speed data from GPS.

6) Indication of alarm

The error messages detected by self diagnostic function are indicated.

- In the first stage adjustment, manual key-in and maintenance

Possible to set manual speed, zero adjustment, milepost measurement, and also to confirm of various data.

- Dimmer LED : LED lamps are added and subtracted

- Input signal by mm buttons.

: Digital signal(NMEA0183)

Input voltage 24V DC

- Wiring position : Coaming of under or back

- Installation : Desk-top, Wall mount or Flash mount

- Construction : Water resist type

- Junction box LN052

The junction box is used for connection between sensor and master unit. And it is connected by maker supply cable and ship-builder supply cable.

- Installation :Wall mount

- Wiring position : Ground with water resist

Yokogawa Denshikiki Co.,Ltd.

- Speed indicator MHR130(Sinqle-axis) / LR525 (Dual-axis)

This is a large analog indicator with an outside diameter of

180mm.

The indicative variation are speed, longitudinal/ transverse speed (for dual-axis) and resultant speed /direction. And the scale boards are prepared 18 kinds include each measurement range.

- Power supply : 24V DC 0.3A (7.5W)

- Capacity : 4 circuits max.

However, the forth is necessary to have the power supply of 24V DC from external.

- Input signal : Digital signal

- Illumination : EL board or LED illumination

- Dimmer : Built-in or external

- Wiring position : Back part

- lnstauration

- Construction

: Flash mount or Wall mount

: Type of water resist

- Dimmer box MKD010/LD001A

For MHR130 / LR525

- Power supply : 1 OOV to 115V or 200V to 230V AC

- Wiring position : Corming

- lnstauration : Flash mount or Wall mount

Sea-bottom (Sensor)

- HS1 type Using the <1>35 sensor, and installed at single or double bottom of ship. Standard length of protraction is 50mm.

- Sensor : Outside diameter : <1>35, length : 400mm with cable (7m/15m)

- Seawater valve : 40A JIS5K Gate valve

- HD1 type Using the<l>35 sensor, and installed with penetration double bottom. Seawater valve is installed on inner sea-bottom.

Standard length of protraction is 50mm.

- Sensor : Outside diameter : <1>35 with rodmeter

(connected by connecter)

- Seawater valve : 40A JIS5K Gate valve

- Protection tube/seawater valve :

Water resist that the sensor and rodmeter go through double bottom.

- FA 1 /FA2 type Using the<l>48 sensor, and installed at single bottom of ship. Standard length of protraction 1 s 13mm or 73mm. FA2 is for dual-axis.

- Sensor : Outside diameter : <1>48, length 345mm

- Seawater valve : 50A JIS5K ball valve

- HV1/HV2 type Using the<l>70 sensor, and installed at single bottom of ship. Standard length of protraction is 7mm or 50mm. HV2 is for dual-axis.

- Sensor : Outside diameter : <1>70, length 510mm

- Seawater valve : 75A JIS5K ball valve

Outline and Type No. and Suffix code Master indicator (Wall mount)

LR523-WO 0-1-0

"' .I I I I, "' L J

GBBBEl3El3El3 Ge 888El3$El3

I

MOUNTING DIMENSION

150±0.5

_l

4-MS or 6 HOLE

Master indicator (Flash mount)

LR523-D00-1-0

PANEL CUT

HOLE

4-C6.5

Master indicator (Flash mount)

LR523-FO 0-1-0

I I e

21s

200+0.5

I I cpoo :xpcp=

PANEL CUT

200:!:0.5

HOLE

4-M5 or cb 6 HOLE/

Yokogawa Denshikiki Co.,Ltd.

MODEL LR523 - W

MASS 1 . 2 kg

COAMING r/>25

TERMINAL CONNECTIONS

24V C

NMEA0183 INPUT

NMEA0183 OUTPUT

MODEL LR523-D

MASS 1 . 3 kg

TERMINAL CONNECTIONS

M ODEL LR5 23-F

MASS 1 1 kg

TERMINAL BOARD

COAMING r/>25

TERMINAL CONNECTIONS

24V DC

NMEA0183 INPUT

NMEAOl83 OUTPUT

Master indicator LR523-X1 • • • X5/ 0ption Type No. Suffix code Note

LR523 .................... For EML500

Style -D Flush mount

-F Flush mount (with bezel)

X1 -w Desk top type or Wall mount

System

I 1 Single-axis

X2 2 Dual-axis

Rule / Name plate 1 None / Japanese & English

2 JG / Japanese & English

3 JG / Japanese

4 None / English

5 MED / Japanese & English (Note 1)

X3 6 MED / English (Note 1)

Color X4 1-1 YDK Standard (CC24 brown)

Name plate -1 HS1

-2 HD1

-3 HV 1

-4 HV 2

-5 FA1

X5 -6 FA2

Option I / CHS Name plate in Chinese

(Note 1) MED is attended in case of System X2 = 1 (Single-axis).

Master unit (Wall mount)

LT501-WDDDDD-D

D D D D

- -- - : __ , 0

EARTH TERMINAL

COAMING 30 x 100 m

Master unit (Flash mount)

LT501-FDDDDD-D

1·

270±0.5

• 1

D D D D

EARTH TERMINAL

Yokogawa Denshikiki Co.,Ltd.

3.2

4- 7 HOLE

MODEL LT501-W

MASS 4 . 9 kg

COAMING 30 x 100

MOUNTING DIMENSION

210±0.5

1-

-1-t I

I

4- M6 or ¢ 7HOLE

MODEL LT501 - F

MASS 6 . 4 kg

11 6

TERMINAL BOARD

COAMING 30 1t 100

PANEL CUT

270±0.5

254.5

0 ~ tl -

"' "' HOLE

4- M6 or 7 HOLE

LT501-Y Master unit

(Wall mount : with corming plate)

LT501-YDDDDD-D

= = = = == c:::::J = :;i D "' D D

D = D = = D

COAMING 30 x 100

Terminal drawing

<D®@@

ANALOG SPEED OUTPUT

OmA to 20mA or 4mA to 20mA

PHOTO OCUPLER OUTPUT

200Pulse/n mile

DIGITAL SPEED OUTPUT

NMEAOt83(VBW)

@GPS BACK-UP INPUT

CONTACT OUTPUT

200Pulse/n mile

@ SHIP'S POWER SUPPLY

MODEL LT5 01-Y

d +--i

MASS 5 . 1 kg

TERMINAL BOARD

210±0.5

I

-1-

I 4-M6 or ¢ 7 HOLE

ALARM CONTACT OUTPUT FOR SPEED LIMIT

13@

ANALOG SPEED OUTPUT

OV DC to 5V DC or 1V DC to 5V DC/FULL RANGE

ALARM CONTACT OUTPUT FOR SYSTEM FAIL

@ SPEED INDICATOR OUTPUT

@ MASTER INDICATOR OUTPUT

@ JUNCTION BOX INPUT/OUTPUT

@)AC POWER FOR OUTPUT

DC POVVER FOR OUWUT

Master unit LT501-X1 • • • X7 /0ption Type No. Suffix code Not e

LT501 .................... For EML500

Style -F Flush mount

-w Wall mount x, -Y Wall mount (with coaming plate)

System 1: Single-axis

X2 Dual-axis (Note 1)

Ship' s power , 100V AC 50/60Hz 1 Cf>

2 110V AC 50/60Hz 1 Cf>

3 115V AC 50/60Hz 1 Cf>

4 200V AC 50/60Hz 1 Cf>

X3 5 220V AC 50/ 60Hz 1 Cf>

Measurement range 1 - 4kn to 20kn

2 - 5kn to 25kn

3 - 7kn to 35kn

4 - Bkn to 40kn

5 -1 Okn to 50kn (Note 2)

X4 6 -1 3kn to 65kn (Note 2)

Rule / Name plate 1 None / Japanese & English

2 JG / Japanese & English

3 JG / J apanese

4 None / English

5 MEO / Japanese & English (Note 3)

X5 6 MEO / English (Note 3)

Color 1 YDK Standard (CC24 brown)

2 Munsell 2.5G7 / 2

X6 3 Munsell 7.5BG7/ 2

Name plate -1 HSl

- 2 HD1

-3 HVl

-4 HV2

-5 FAl

X7 -6 FA2

Option / AN1 Alarog output (Connect LR522)

/ AN5 Analog out.put

/ ANF1 Analog output

/ ANF5 Anarog output (OV to 5V DC output)

/CHS Name plate in Chinese

/GPS External speed signal input (Note 4)

(Note 1) In case of dual-axis, transverse speed may not be able to the mounting position of sensor.

(Note 2) About 50160kt correspondence, additional e ngineering is required concerning t he installat ion of the sensor.

(Note 3) MEO is attended in case of System X2 = 1 (Singte- axis) and X4 = 1 (-4kn to 2otsn) or X4 = 2 (-5kn to 25kn)

(Note 4) Please append external speed s ignal (NMEA0183) format with order sheet.

Options : Analog output list

/AN5

(j)

/ AN1

(2)

/ AN F5

:Ji

/ANF1

l2J ~··-1~~ ~ ... Okt = OV +Full kt = 5V Ol<.t = 1V +Fullkt =5V

Omom ,,_co,o LJO"~~,cacc,ac I

.•.•. 1V i Ship0 sspeed : i Ship0 sspeed

- Fullkt-OV +Full kt - 5V - Full kt= 1V +Fullkt =-5V

Osco• ""'" ~ o;:;:~~""' '

4mA !

Ship. s speed : : Ship " s sp~ed

- Full ~l OmA +Full kt 20mA -Full kl = 4mA +Full kt = 20mA

Yokogawa Denshikiki Co.,Ltd.

Junction box

LN052-WDDD-D

MOUNTING DIMENSION

MODEL LN052

MAS S 0 . 8 kg

TERMINAL BOARD

TERMINAL CONNECTIONS

FROM

MASTER UNIT

A : OmA to 20mA - C,D t-15V. - 15V

E.F.G : 24V DC

TO SENSOR

A : OmA to 20mA C.0 : +15V, - 15V

E.F : 24V DC

Junction box LN052-X1 · · · X5/ 0 ption Type No. Suffix code Not e

LN052 .................... For EML500/ 50

Style X l -w Wall mount

Rule / Name plate 1 None / Japanese & English

2 JG / J apanese & English

3 JG / J apanese

4 None / English

5 MED / J apanese & English (Not e 3)

X2 6 MED / English (Note 3)

Color 1 Munsell 2.5G7 / 2

X3 2 Munsell 7.5G7/ 2

Grand size 1 20c

2 25a

3 25b

X4 4 25c

Name plate -3 HSl

-4 HD1

-5 HV1

- 6 HV2

-7 FAl

X5 - 8 FA2

Option I / CHS Name plate in Chinese

Analog indicator (Wall mount)

MHR130-SPD-WO 0-0 0 0-0 0 0-0 0-0 0 0

Y-View (Back side)

Analog indicator (Flash mount)

MHR130-SPD-FO 0-0 0 0-0 0 0-0 0-0 0 0

-...-Y

4-</>5.5M5

Y-View (Back side)

Yokogawa Denshikiki Co.,Ltd.

Scale plate list

From -4kt to 20kt From -5kt to 25kt

From - 7kt to 35kt From -10kt to 50kt

Analog indicator MHR130-X1 • ··X12/0ption Model Suffix Specification

MHR130 .......................... Analog indicator

Function X1 -SPD Speed indicator

Style 1-F

Flash mount

X2 -W Wall mount

Cable inlet 1

1:

Coaming Note 1

X3 Grand Note 2

Cable inlet 2 0 Not use

1 Coaming

X4 2 Grand

Power supply 1-1

100-220VAC,50/60Hz, 1 </J

X5 -2 24VDC (Non isolate)

Dimmer 0 Without dimmer

1 Built in dimmer

2 DC dimmer supply by YDK

3 DC dimmer supply by YARD

X6 4 100V AC dimmer supply by YARD

Back.light color 0 Non

1 Umber

X7 2 Green

Scale range -S20 -4kn to 20kn

-S25 -5kn to 25kn

-S35 -7kn to 35kn

X8 -S50 -1 Okn to 50kn

Input signal 1-21 Speed signal (PYDK, 4800bps)

X9 -22 Speed signal (PYDK, 9600bps)

Standards -0 Not applicable

-1 JG

X10 -2 MED (wheel mar1c)

Name plate

1:

Japanese and English

X 11 English

Paint color 1 Munsell 0.8Y2.5/0.4 (LAMP BLACK)

2 Munsell 2 .5G7/2

X12 3 Munsell 7.5BG7/2

Option IC Chinese name plate

/ HS1 For HS1 system

/ HD1 For HD1 system

/HV1 For HV1 system

I FA1 For FA1 system

Note1} If selected X3 = 1 Coaming, will you select X4 = 1 Coaming.

Note2} If selected X3 = 1 Grand, will you select X4 = O Non or 2 Grand.

MRD010 Dimmer box

MRD01 O-W-20F-D DD D

4-

<O

CABLE GRAND

20f (20a to 20c)

Dimmer box MRD010-X1 ···XS Model Suffix

MKD010

Style X1 -W

Cable inlet X2 l-20F

Standards 1; X3

Name plate I: X4

Paint color I: X5

Yokogawa Denshikiki Co.,Ltd.

e

Specification

Dimmer box

Wall mount (Water proof)

Glands 201

Not applicable

MED (wheel mark)

Japanese and English

English

Munsell 2.5G7/2

Munsell 7.5BG7/2

MRD011-N Dimmer unit (Dimmer only)

MRDOl 1-NDD-D

MRD011-F Dimmer unit (Flash mount)

MRD011-ND0-D

Dimmer unit MRD011-X1 · · ·X4 Model Suffix Specification

MRD011 ................. .. ....... Dimmer unit

Style -N Dimmer only

X1 -F Flash mount

Standards I~ Not applicable

X2 MED (wheel mark)

Name plate I: Japanese and English

X3 English

Paint color 1 · 1

Note 1 Munsell 0.8Y2.5/0.4 (LAMP BLACK)

X4 .4 Note 2

Note 1) If you select X1 =-N, Please select X4=-1.

Note 2) If you select X 1 =-F, Please select X4=-4.

Black

Analog indicator (Wall mount)

LR525-WD D-D DD D D-D

MOUNTING DIMENSION

120±0.5

4- MlO or dJ 11 HOLE

¢JO HOLE

Analog indicator (Flash mount)

LR525-FDD-DDDDD-D

4- M6 or

Yokogawa Denshikiki Co.,Ltd.

MODEL LR525 - W

MASS 4 . 1kg

~.4S m ~

TERMINAL BOARD

CABLE INLET 25

MGNETIC COMPASS SAFE DISTANCE LABEL

TERMINAL CONNECTIONS

24V DC

MODEL LR525-F

MASS 3 . 8 kg

26 99

TERMINAL BOARD

CABLE INLET ¢ 25

BEL

TERMINAL CONNECTIONS

I

Scale plate list resultant speed /direction longitudinal / transverse speed

Built-in dimmer EL boa rd illumination

24V DC

Separate dimmer EL board illumination

TERMINAL CONNECTIONS

r

Built - in dimmer LED illumination

TERMINAL CONNECTIONS

NMEA0183 INPUT

'------:1 24V DC

Separate dimmer LED illumination

TERMINAL CONNECTIONS

NMEA0183 INPUT

·------:· 24V DC

Speed indicator (Dual axis) LR525-X1 • • • X9/ 0ption Type No. Suffix code Not e

LR525 .................... For EML500 (Dual-axis)

Style -F Flush mount

X1 -w Desk top type or Wall mount

Measurement range 1 - 4kn to 20kn (Note 1)

2 - 5kn to 25kn

3 - 7 kn t o 35kn

4 - Bkn to 40kn

5 -1 Okn to 5Dkn

X2 6 -13kn to 65kn

Scale plate 1: Longitudinal / Transverse s peed

X3 Result ant speed / Direction

Illumination -A LED Orange color

-B LED Green color

-G EL board Green cok>r

-N Illumination not use

X4 -R EL board Orange color

Dimmer / Power supply 1 External/100V to 115V AC 50/60Hz 1 <P

2 (Note 2) Built-in / 100V to 115V AC 50/ 60Hz 1 <P

3 External/ 200V to 230V AC 50/ 60Hz 1 <P

4 (Note 2) Built-in /200V to 230V AC 5D/ 60Hz 1 <P

5 External/ LED illuminat ion

6 Built-in / LED illumination

X5 N Illumination not use

Wiring position 1: Cormingc/>2S

X6 Grand (Note 3)

Rule / Name plate 1 None / Japanese & Engtish

2 JG / Japanese & English

3 J G / J apanese

X7 4 None / Englis h

Color 1 YDK Standard (CC24 brown)

2 Munsell 2.5G7/ 2

XB 3 Munsell 7.5BG7/ 2

Name plate 1-1

HV 2

X9 -2 FA2

Option I / CHS Name plate in Chines e

(Note 1) Case of Res ultant s peed / Direction are not indicat e (- ) data. Indicate 0 to XX kt .

(Note 2) XS = 2 and XS = 4 are use for LR525 built- in dimmer unit o~y.

(Note 3) X6 = 2 Grand is use for Wall mount only. (15b, 20c each 1 use)

Dimmer box (Flash mount type)

LD001 A-FD D D-D

(Connection diagram is for EL board)

66±0.2

MODEL L0001A-F

MASS 0 .5 kg

PANEL CUT

CONNECTION DIAGRAM

va, I 2ok2

I ·fil'A ,' I 6_:...Q 0 Uo V -· .

COAMING 20 MAGNETIC COMPASS SAFE DISTANCE LABEL

Dimmer box (Wall mount type)

LD001A-W0DD-D

(Connection diagram is for EL board)

M ODEL LD001A-W

MASS 0.5 kg

NAME PLATE

J- ~:,?- r/J 20 COAMING r/,20

MOUNTING DIMENSION

25±0.5

"' 0 ti g:J ~

2-M6 or r/J 7 HOLE

Yokogawa Denshikiki Co.,Ltd.

MAGNETIC COMPASS SAFE DISTANCE LABEL

CONNECTION DIAGRAM

Dimmer switch

LD002-ADD1

MODEL L D002

M A SS 0 . 1 kg

(Connection diagram is for LED illumination)

VARIABLE RESISTOR 20kQ 0.8w

12±0.3

M9 PO. 75

PANEL CUT

f ~ -;i

2 . KNOB

3. NAME PLATE

4.

NAME PLATE

1• 31.5 ·1~ I FOR SPEED ll«>fC ATOR I a:, I '""""'" I

CONNECTION DIAGRAM

2;;;;; I I 3

Dimmer box LD001A-X1 • • • X5/ 0ption

Type No. Suffix code Note

LDOOlA .................... For EML500/ 50

;<.1'·1'1~ Xl -F Flush mount

-w Wall mount

Rule / Name plate 1 None / J apanese & English

2 JG I Japanese & Engtish

3 JG I Japanese

5 None / English

6 MED / Japanese & English (Not e 3)

X2 7 MED / English (Note 3)

Color 1: Munsell 2.5G7 / 2

X3 Munsell 7.5BG7/2

Power supply 1 100V AC to 115V AC

2 200V AC to 220V AC

X4 3 For LED illumination

Name plate -1 HS1

-2 HD1

-3 HV1

-4 HV2

-5 FA1

X5 -6 FA2

Option I /CHS Name plate in Chinese

Dimmer switch LD002-X1 • • • X4 Type No. Suffix code Note

LDOOlA .................... For EML500/50

Style Xl -A Inner parts only

Power supply 1 200V

2 100V

X2 3 For LED illumination

Name plate 1: Japanese

X3 English

Usable equipment X4 I 1 LR524 / LR525