Attachment_4_Spec_087100_Rev_27APR2018.pdf

FLORIDA AIR NATIONAL GUARD – 125TH FIGHTER WING April 27, 2018 REV

RESTORATION, MODERNIZATION AND SUSTAINMENT PROGRAM

ALTER WEAPONS RELEASE 1020

JACKSONVILLE INTERNATIONAL AIRPORT

100% ISSUED FOR BID SUBMISSION

DOOR HARDWARE 08 71 00 - 1

SECTION 08 71 00 - DOOR HARDWARE

PART 1 - GENERAL

1.1 SUMMARY

A. This section includes items known commercially as finish or door hardware that are required for swing, sliding, and folding doors, except special types of unique hardware specified in the same sections as the doors and door frames on which they are to be installed.

B. This Section includes the following:

1. Hinges.

2. Key control systems.

3. Lock cylinders and keys.

4. Lock and latch sets.

5. Bolts.

6. Exit devices.

7. Push/pull units.

8. Closers.

9. Overhead holders.

10. Miscellaneous door control devices.

11. Protection plates.

12. Weatherstripping for exterior doors.

13. Thresholds.

1.2 SUBMITTALS

A. General: Submit the following in accordance with Conditions of Contract and Division 1 Specification sections.

B. Product data including manufacturer’s technical product data for each item of door hardware, installation instructions, maintenance of operating parts and finish, and other information necessary to show compliance with requirements.

C. Final hardware schedule coordinated with doors, frames, and related work to ensure proper size, thickness, hand, function, and finish of door hardware.

1. Final Hardware Schedule Content: Based on hardware indicated, organize schedule into “hardware sets” indicating complete designations of every item required for each door or opening. Include the following information:

a. Type, style, function, size, and finish of each hardware item.

b. Name and manufacturer of each item.

ALTER WEAPONS RELEASE 1020

DOOR HARDWARE 08 71 00 - 2

c. Fastenings and other pertinent information.

d. Location of each hardware set cross referenced to indications on Drawings, both on floor plans and in door and frame schedule.

e. Explanation of all abbreviations, symbols, and codes contained in schedule.

f. Mounting locations for hardware.

g. Door and frame sizes and materials.

h. Keying information.

2. Submittal Sequence: Submit final schedule at earliest possible date, particularly where acceptance of hardware schedule must precede fabrication of other work that is critical in the Project construction schedule. Include with schedule the product data, samples, shop drawings of other work affected by door hardware, and other information essential to the coordinated review of schedule.

3. Keying Schedule: Submit separate detailed schedule indicating clearly how the Government’s final instructions on keying of locks has been fulfilled.

D. Submit samples of each type of exposed hardware unit as required in finish indicated and tagged with full description for coordination with schedule. Submit samples prior to submission of final hardware schedule.

1. Samples will be returned to the supplier. Units that are acceptable and remain undamaged through submittal, review, and field comparison process may, after final check of operation, be incorporated in the Work, within limitations of keying coordination requirements.

E. Templates for doors, frames, and other work specified shall be factory prepared for the installation of door hardware. Check shop drawings of other work to confirm that adequate provisions are made for locating and installing door hardware to comply with indicated requirements.

F. All test results shall be a required submittal to the Government.

G. Contractor shall submit qualifications of any required Independent Testing and Inspection Agent in advance for Government approval.

1.3 QUALITY ASSURANCE

A. Single Source Responsibility: Obtain each type of hardware (latch and lock sets, hinges, closers, etc.) from a single manufacturer.

B. Supplier Qualifications: A recognized architectural door hardware supplier, with warehousing facilities in the Project’s vicinity, that has a record of successful in-service performance for supplying door hardware similar in quantity, type, and quality to that indicated for this Project and that employs an experienced architectural hardware consultant (AHC) who is available to Contracting Officer and Contractor, at reasonable times during the course of the Work, for consultation.

ALTER WEAPONS RELEASE 1020

DOOR HARDWARE 08 71 00 - 3

1. Require supplier to meet with Government to finalize keying requirements and to obtain final instructions in writing.

C. Fire-Rated Openings: Provide door hardware for fire-rated openings that complies with NFPA Standard No. 80 and requirements of authorities having jurisdiction. Provide only items of door hardware that are listed and are identical to products tested by UL, Warnock Hersey, FM, or other testing and inspecting organization acceptable to authorities having jurisdiction for use on types and sizes of doors indicated in compliance with requirements of fire-rated door and door frame labels. All fire seals required for fire rated wood doors shall be furnished by the door manufacturer or supplier.

1.4 PRODUCT HANDLING

A. Tag each item or package separately with identification related to final hardware schedule, and include basic installation instructions with each item or package.

B. Packaging of door hardware is responsibility of supplier. As material is received by hardware supplier from various manufacturers, sort and repackage in containers clearly marked with appropriate hardware set number to match set numbers of approved hardware schedule. Two or more identical sets may be packed in same container.

C. Inventory door hardware jointly with representatives of hardware supplier and hardware installer until each is satisfied that count is correct.

D. Deliver individually packaged door hardware items promptly to place of installation (shop or Project site).

E. Provide secure lock-up for door hardware delivered to the Project, but not yet installed. Control handling and installation of hardware items that are not immediately replaceable so that completion of the Work will not be delayed by hardware losses both before and after installation.

1.5 MAINTENANCE

A. Maintenance Tools and Instructions: Furnish a complete set of specialized tools and maintenance instructions as needed for Government’s continued adjustment, maintenance, and removal and replacement of door hardware.

PART 2 - PRODUCTS

2.1 MANUFACTURERS

A. Manufacturers: Subject to compliance with requirements, provide products by one of the following:

ALTER WEAPONS RELEASE 1020

DOOR HARDWARE 08 71 00 - 4

1. Butts and Hinges:

a. Bommer Industries, Inc.

b. Hager Hinge Co.

c. McKinney Products Co, an ASSA ABLOY Group Company.

2. Key Control System

a. Telkee Inc.

b. Alladin

c. Lund Equipment Company, Inc.

d. MMF Industries

3. Cylinders and Locks:

a. Match existing coordinate with Contracting Officer.

4. Bolts

a. Sargent Manufacturing Company, an ASSA ABLOY Group Company.

b. McKinney Products Co, an ASSA ABLOY Group Company.

c. Rockwood Manufacturing.

d. Triangle Brass Manufacturing Company (TRIMCO).

5. Exit/Panic Devices

a. Corbin Russwin Architectural Hardware, an ASSA ABLOY Group Company.

ED5000 series.

b. Sargent Manufacturing Company, an ASSA ABLOY Group Company. 80 series.

c. Yale Commercial Locks and Hardware, an ASSA ABLOY Group Company. 7000 series.

6. Push/Pull Units:

a. Baldwin Hardware Corp.

b. Hiawatha, Inc.

c. McKinney Products Co, an ASSA ABLOY Group Company.

d. Rockwood Manufacturing.

e. Triangle Brass Manufacturing Company (Trimco).

7. Overhead Closers:

a. Corbin Russwin Architectural Hardware, an ASSA ABLOY Group Company.

DC6000 series.

b. Norton Door Controls, an ASSA ABLOY Group Company. 8000 series.

c. Sargent Manufacturing Company, an ASSA ABLOY Group Company. 1431 series.

ALTER WEAPONS RELEASE 1020

DOOR HARDWARE 08 71 00 - 5

d. Yale Commercial Locks and Hardware, an ASSA ABLOY Group Company. 3000 series.

8. Door Control Devices:

a. Baldwin Hardware Corp.

b. McKinney Products Co, an ASSA ABLOY Group Company.

c. Rixson Specialty Door Controls, an ASSA ABLOY Group Company.

d. Rockwood Manufacturing.

e. Triangle Brass Manufacturing Company (Trimco).

9. Door Trim Units:

a. Baldwin Hardware Corp.

b. McKinney Products Co, an ASSA ABLOY Group Company.

c. Rockwood Manufacturing.

d. Triangle Brass Manufacturing Company (Trimco).

10. Kick, Mop, and Armor Plates:

a. Baldwin Hardware Corp.

b. McKinney Products Co, an ASSA ABLOY Group Company.

c. Rockwood Manufacturing.

d. Triangle Brass Manufacturing Company (Trimco).

11. Door Stripping and Seals:

a. National Guard Products, Inc.

b. Pemko Manufacturing Co., Inc.

c. Reese Enterprises, Inc.

d. McKinney Products Co, an ASSA ABLOY Group Company.

e. Zero International, Inc.

12. Thresholds:

a. National Guard Products, Inc.

b. Pemko Manufacturing Co., Inc.

c. Reese Enterprises Inc.

d. McKinney Products Co, an ASSA ABLOY Group Company.

e. Zero International, Inc.

2.2 SCHEDULED HARDWARE

A. Requirements for design, grade, function, finish, size, and other distinctive qualities of each type of finish hardware are indicated in the “Hardware Schedule” at the end of this Section.

Products are identified by using hardware designation numbers of the following:

ALTER WEAPONS RELEASE 1020

DOOR HARDWARE 08 71 00 - 6

1. Manufacturer’s Product Designations: The product designation and name of one manufacturer are listed for each hardware type required for the purpose of establishing minimum requirements. Provide either the product designated or, where more than one manufacturer is specified under the Article “Manufacturers” in Part 2 for each hardware type, the comparable product of one of the other manufacturers that complies with requirements.

2. ANSI/BHMA designations used elsewhere in this Section or in schedules to describe hardware items or to define quality or function are derived from the following standards.

Provide products complying with these standards and requirements specified elsewhere in this Section.

a. Butts and Hinges: ANSI/BHMA A156.1-06.

b. Bored and Preassembled Locks and Latches: ANSI/BHMA A156.2-03.

c. Exit Devices: ANSI/BHMA A156.3-01.

d. Door Controls - Closers: ANSI/BHMA A156.4-00.

e. Auxiliary Locks and Associated Products: ANSI/BHMA A156.5-01.

f. Architectural Door Trim: ANSI/BHMA A156.6-05.

g. Template Hinge Dimensions: ANSI/BHMA A156.7-03.

h. Door Controls - Overhead Stops and Holders: ANSI/BHMA A156.8-05.

i. Interconnected Locks and Latches: ANSI/BHMA A156.12-05.

j. Mortise Locks and Latches Series 1000: ANSI/BHMA A156.13-05.

k. Sliding and Folding Door Hardware: ANSI/BHMA A156.14-07.

l. Release Devises – Closer Holder, Electromagnetic and Electromechanical:

ANSI/BHMA A156.15-06.

m. Auxiliary Hardware: ANSI/BHMA A156.16-02.

n. Recommended Practices for Materials and Finishes: ANSI/BHMA A156.18-06.

o. Power Assist and Low Energy Operated Doors: ANSI/BHMA A156.19-07.

p. Thresholds: ANSI/BHMA A156.21-06.

q. Door Gasketing and Edge Seal Systems: ANSI/BHMA A156.22-05.

r. Electromagnetic Locks: ANSI/BHMA A156.23-04.

s. Delayed Egress Locking Systems: ANSI/BHMA A156.24-03.

t. Electrified Locking Devices: ANSI/BHMA A156.25-02.

u. Continuous Hinges: ANSI/BHMA A156.27-06.

v. Recommended Practices for Keying Systems: ANSI/BHMA A156.28.07.

w. Exit Locks, Exit Locks with Exit Alarms, Exit Alarms, Alarms for Exit Devices:

ANSI/BHMA A156.29-07.

x. High Security Cylinders: ANSI/BHMA A156.30-03.

y. Electric Strikes and Frame Mounted actuators: ANSI/BHMA A156.31-07.

2.3 MATERIALS AND FABRICATION

A. Manufacturer’s Name Plate: Do not use manufacturers’ products that have manufacturer’s name or trade name displayed in a visible location (omit removable nameplates) except in conjunction with required fire-rated labels and as otherwise acceptable to Contracting Officer.

1. Manufacturer’s identification will be permitted on rim of lock cylinders only.

ALTER WEAPONS RELEASE 1020

DOOR HARDWARE 08 71 00 - 7

B. Base Metals: Produce hardware units of basic metal and forming method indicated using manufacturer’s standard metal alloy, composition, temper, and hardness, but in no case of lesser (commercially recognized) quality than specified for applicable hardware units for finish designations indicated.

C. Fasteners: Provide hardware manufactured to conform to published templates, generally prepared for machine screw installation. Do not provide hardware that has been prepared for self-tapping sheet metal screws, except as specifically indicated.

D. Furnish screws for installation with each hardware item. Provide Phillips flat-head screws except as otherwise indicated. Finish exposed (exposed under any condition) screws to match hardware finish or, if exposed in surfaces of other work, to match finish of this other work as closely as possible including “prepared for paint” surfaces to receive painted finish.

E. Provide concealed fasteners for hardware units that are exposed when door is closed except to the extent no standard units of type specified are available with concealed fasteners. Do not use thru-bolts for installation where bolt head or nut on opposite face is exposed in other work unless their use is the only means of reinforcing the work adequately to fasten the hardware securely. Where thru-bolts are used as a means of reinforcing the work, provide sleeves for each thru-bolt or use sex screw fasteners.

2.4 HINGES, BUTTS, AND PIVOTS

A. Templates: Provide only template-produced units.

B. Screws: Provide Phillips flat-head screws complying with the following requirements:

1. For metal doors and frames install machine screws into drilled and tapped holes.

2. For fire-rated wood doors install#12 x 1-1/4-inch, threaded-to-the-head steel wood screws.

3. Finish screw heads to match surface of hinges or pivots.

C. Hinge Pins: Except as otherwise indicated, provide hinge pins as follows:

1. Out-Swing Exterior Doors: Non-removable pins.

2. Out-Swing Corridor Doors with Locks: Non-removable pins.

3. Interior Doors: Non-rising pins.

4. Tips: Flat button and matching plug, finished to match leaves.

D. Number of Hinges: Provide number of hinges indicated but not less than 3 hinges per door leaf for doors 90 inches or less in height and one additional hinge for each 30 inches of additional height.

1. Fire-Rated Doors: Not less than 3 hinges per door leaf for doors 86 inches or less in height with same rule for additional hinges.

ALTER WEAPONS RELEASE 1020

DOOR HARDWARE 08 71 00 - 8

2.5 LOCK CYLINDERS AND KEYING

A. Standard System: Provide new key system for Project; coordinate with Contracting Officer.

B. Equip locks with cylinders for interchangeable-core pin tumbler inserts. Furnish only temporary inserts for the construction period, and remove these when directed. Cylinders are to have seven (7) active pins and shall be small format.

C. Metals: Construct lock cylinder parts from brass or bronze, stainless steel, or nickel silver.

D. Comply with Government’s instructions for keying and, except as otherwise indicated, provide individual change key for each lock that is not designated to be keyed alike with a group of related locks.

1. Permanently inscribe each key with number of lock that identifies cylinder manufacturer’s key symbol, and notation, “DO NOT DUPLICATE”.

E. Key Material: Provide keys of nickel silver only.

F. Key Quantity: Furnish 3 change keys for each lock.

1. Furnish one extra blank for each lock.

2. Furnish ten construction Keys.

3. Furnish two control keys for construction cores to remove / insert construction cores.

4. Furnish two control keys for permanent cores to remove / insert permanent cores.

5. Deliver all permanent keys to Government.

2.6 KEY CONTROL SYSTEM

A. Provide a key control system including envelopes, labels, tags with self-locking key clips, receipt forms, 3-way visible card index, temporary markers, permanent markers, and standard metal cabinet, all as recommended by system manufacturer, with capacity for 150 percent of the number of locks required for the Project.

1. Provide hinged-panel type cabinet for wall mounting.

2.7 LOCKS, LATCHES, AND BOLTS

A. Strikes: Provide manufacturer’s standard wrought box strike for each latch or lock bolt, with curved lip extended to protect frame, finished to match hardware set, unless otherwise indicated.

1. Provide flat lip strikes for locks with 3-piece, anti-friction latchbolts as recommended by manufacturer.

2. Provide extra long strike lips for locks used on frames with applied wood casing trim.

3. Provide recess type top strikes for bolts locking into frame heads, unless otherwise indicated.

ALTER WEAPONS RELEASE 1020

DOOR HARDWARE 08 71 00 - 9

4. Provide dust-proof strikes for foot bolts, except where special threshold construction provides non-recessed strike for bolt.

5. Provide roller type strikes where recommended by manufacturer of the latch and lock units.

B. Lock Throw: Provide 3/4-inch minimum throw of latch on pairs of doors. Comply with UL requirements for throw of bolts and latch bolts on rated fire openings.

1. Provide 3/4-inch minimum throw of latch for mortise locks. Provide 1-inch minimum throw for all dead bolts.

C. Flush Bolt Heads: Minimum of 1/2-inch-diameter rods of brass, bronze, or stainless steel with minimum 12-inch-long rod for doors up to 7'-0" in height. Provide longer rods as necessary for doors exceeding 7'-0" in height.

D. Exit Device Dogging: Except on fire-rated doors where closers are provided on doors equipped with exit devices, equip the units with hex-keyed dogging device to keep the latch bolt retracted, when engaged.

2.8 PUSH/PULL UNITS

A. Concealed Fasteners: Provide manufacturer’s special concealed fastener system for installation, thru-bolted for matched pairs but not for single units.

2.9 CLOSERS AND DOOR CONTROL DEVICES

A. Size of Units: Except as otherwise specifically indicated, furnish units that are adjustable through a range of sizes (1 – 6).

1. Provide parallel arms for all overhead closers, except as otherwise indicated.

B. Access-Free Manual Closers: Where manual closers are indicated for doors required to be accessible to the physically handicapped, provide adjustable units complying with ANSI A117.1 provisions for door opening force and delayed action closing.

C. Provide black resilient parts for exposed bumpers.

2.10 DOOR TRIM UNITS

A. Fasteners: Provide manufacturer’s standard exposed fasteners for door trim units consisting of either machine screws or self-tapping screws.

B. Fabricate protection plates not more than 2 inches less than door width on hinge side and not more than 2 inch less than door width on pull side by height indicated.

ALTER WEAPONS RELEASE 1020

DOOR HARDWARE 08 71 00 - 10

1. Metal Plates: Stainless steel, 0.050 inch (U.S. 18 gage).

2.11 WEATHERSTRIPPING AND SEALS

A. General: Provide continuous weatherstripping on exterior doors and smoke, light, or sound seals on interior doors where indicated or scheduled. Provide non-corrosive fasteners for exterior applications and elsewhere as indicated.

B. Replaceable Seal Strips: Provide only those units where resilient or flexible seal strip is easily replaceable and readily available from stocks maintained by manufacturer.

2.12 THRESHOLDS

A. General: Except as otherwise indicated, provide standard metal threshold unit of type, size, and as scheduled.

2.13 HARDWARE FINISHES

A. Match items to the manufacturer’s standard color and texture finish for the latch and lock sets (or push-pull units if no latch or lock sets).

B. Provide finishes that match those established by BHMA or, if none established, match the Contracting Officer’s sample.

C. Provide quality of finish, including thickness of plating or coating (if any), composition, hardness, and other qualities complying with manufacturer’s standards, but in no case less than specified by referenced standards for the applicable units of hardware.

D. Provide protective lacquer coating on all exposed hardware finishes of brass, bronze, and aluminum, except as otherwise indicated. The suffix A-NL@ is used with standard finish designations to indicate “no lacquer”.

E. The designations used in schedules and elsewhere to indicate hardware finishes are the industry-recognized standard commercial finishes, except as otherwise noted.

1. Rust-Resistant Finish: For iron and steel base metal required for exterior work and in areas shown as “High Humidity” areas (and also when designed with the suffix-RR), provide 0.2-mil-thick copper coating on base metal before applying brass, bronze, nickel, or chromium plated finishes.

ALTER WEAPONS RELEASE 1020

DOOR HARDWARE 08 71 00 - 11

PART 3 - EXECUTION

3.1 INSTALLATION

A. Mount hardware units at heights indicated in following applicable publications, except as specifically indicated or required to comply with governing regulations and except as otherwise directed by Contracting Officer.

1. “Recommended Locations for Builders Hardware for Standard Steel Doors and Frames” by the Door and Hardware Institute.

B. Install each hardware item in compliance with the manufacturer’s instructions and recommendations. Where cutting and fitting is required to install hardware onto or into surfaces that are later to be painted or finished in another way, coordinate removal, storage, and reinstallation or application of surface protection with finishing work specified in the Division 9 Sections. Do not install surface-mounted items until finishes have been completed on the substrates involved.

C. Set units level, plumb, and true to line and location. Adjust and reinforce the attachment substrate as necessary for proper installation and operation.

D. Drill and countersink units that are not factory prepared for anchorage fasteners. Space fasteners and anchors in accordance with industry standards.

E. Set thresholds for exterior doors in full bed of sealant complying with requirements specified in Section 07 92 00, “Joint Sealants.”

F. Weatherstripping and Seals: Comply with manufacturer’s instructions and recommendations to the extent installation requirements are not otherwise indicated.

3.2 ADJUSTING, CLEANING, AND DEMONSTRATING

A. Adjust and check each operating item of hardware and each door to ensure proper operation or function of every unit. Replace units that cannot be adjusted to operate freely and smoothly or as intended for the application made.

1. Where door hardware is installed more than one month prior to acceptance or occupancy of a space or area, return to the installation during the week prior to acceptance or occupancy and make final check and adjustment of all hardware items in such space or area. Clean operating items as necessary to restore proper function and finish of hardware and doors. Adjust door control devices to compensate for final operation of heating and ventilating equipment.

B. Clean adjacent surfaces soiled by hardware installation.

ALTER WEAPONS RELEASE 1020

DOOR HARDWARE 08 71 00 - 12

C. Instruct Government’s personnel in the proper adjustment and maintenance of door hardware and hardware finishes.

D. Six-Month Adjustment: Approximately six months after the date of Substantial Completion, the Installer, accompanied by representatives of the manufacturers of latchsets and locksets and of door control devices, and of other major hardware suppliers, shall return to the Project to perform the following work:

1. Examine and re-adjust each item of door hardware as necessary to restore function of doors and hardware to comply with specified requirements.

2. Consult with and instruct Government’s personnel in recommended additions to the maintenance procedures.

3. Replace hardware items that have deteriorated or failed due to faulty design, materials, or installation of hardware units.

4. Prepare a written report of current and predictable problems (of substantial nature) in the performance of the hardware.

3.3 HARDWARE SCHEDULE

A. General: Provide hardware for each door to comply with requirements of this Section, “Door Hardware,” hardware set numbers indicated in door schedule, and in the following schedule of hardware sets.

1. Hardware sets indicate quantity, item, manufacturer and product designation, size, and finish or color, as applicable.

Hardware Sets

Set: 21.0

Doors: 1002A, 1002B

2 Continuous Hinge CFMxxSLF-HD1 x door height PE

1 Concealed Vert Rod Exit 8600 x 8650 US32D AD

1 Concealed Vert Rod Exit 8600 US32D AD

1 Cylinder 41 US26D SA

2 Pull RM202 US32D RO

2 Surface Closer UNI8501 689 NO

1 Threshold 2005AV x door width PE

Notes: -Weather seals to be provided by door manufacturer -Provide necessary drop plates and fillers for proper installation of door closers -Exterior doors and hardware to comply with FBC windstorm requirements.

Set: 22.0

Doors: 1001B, 1009B

ALTER WEAPONS RELEASE 1020

DOOR HARDWARE 08 71 00 - 13

1 Continuous Hinge CFMxxSLF-HD1 x door height PE

1 Concealed Vert Rod Exit 8600 x 8650 US32D AD

1 Cylinder 41 US26D SA

1 Pull RM202 US32D RO

2 Surface Closer UNI8501 689 NO

1 Threshold 2005AV x door width PE

Notes: -Weather seals to be provided by door manufacturer -Provide necessary drop plates and fillers for proper installation of door closers -Exterior doors and hardware to comply with FBC windstorm requirements.

Set: 23.0

Doors: 1008

3 Hinge (heavy weight) T4A3386 NRP 4-1/2" x 4-1/2" US32D MK

1 Mortise Lock PBR 8840FL 626 YA

1 Surface Closer UNI8501H 689 NO

1 Kick Plate K1050 8" x 2"LDW US32D RO

1 Threshold 2005AV x door width PE

1 Rain Guard 346C x door width plus 4" PE

1 Gasketing 303CS head & jambs PE

1 Sweep 315CN x door width PE

Notes: -Exterior doors and hardware to comply with FBC windstorm requirements.

Set: 24.0

Doors: 1001A, 1009A

3 Hinge (heavy weight) T4A3386 NRP 4-1/2" x 4-1/2" US32D MK

1 Exit Device (rim, classroom) 7150 WS PB626F 1109 x 6-Pin ECK1 630 YA

1 Surface Closer UNI8501 689 NO

1 Kick Plate K1050 8" x 2"LDW US32D RO

1 Threshold 2005AV x door width PE

1 Rain Guard 346C x door width plus 4" PE

1 Gasketing 303CS head & jambs PE

1 Sweep 315CN x door width PE

Notes: -Exterior doors and hardware to comply with FBC windstorm requirements.

Set: 25.0

Doors: 1010

ALTER WEAPONS RELEASE 1020

DOOR HARDWARE 08 71 00 - 14

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK

1 Cylindrical Lock PB 4705LN 626 YA

1 Surface Closer 8501 600 x 689 NO

1 Kick Plate K1050 8" x 2"LDW US32D RO

1 Door Stop 442 or 409 as required

US26D /

US32D

RO

3 Silencer 608 RO

Set: 26.0

Doors: 1004

1 Cylindrical Lock PB 4708LN 626 YA

1 Surface Closer 8501 600 x 689 NO

1 Kick Plate K1050 8" x 2"LDW US32D RO

1 Door Stop 442 or 409 as required

US26D /

US32D

RO

Set: 27.0

Doors: 1007

6 Hinge TA2714 4-1/2" x 4-1/2" US26D MK

1 Dust Proof Strike 570 US26D RO

2 Flush Bolt 555 US26D RO

1 Cylindrical Lock PB 4705LN 626 YA

2 Surface Overhead Stop 9-X36 652 RF

2 Silencer 608 RO

Set: 28.0

Doors: 1005, 1006

1 Cylindrical Lock PB 4708LN 626 YA

1 Surface Closer 8501 600 x 689 NO

1 Kick Plate K1050 8" x 2"LDW US32D RO

1 Door Stop 442 or 409 as required US26D / RO

ALTER WEAPONS RELEASE 1020

DOOR HARDWARE 08 71 00 - 15

US32D

Set: 29.0

Doors: 1003

1 Specialty Dr Hardware furnished by Dr Mfg 00

END OF SECTION 08 71 00