TE_T_-_Request_for_Training_Resources_Redacted.pdf

TECHNICAL EXHIBIT T

REQUEST FOR TRAINING RESOURCES

Technical Exhibit T contains the following examples:

Request For Training Resources (RFMSS)

Scenario Input Guide Sheet

FHT Form 200-X10, Dig Permit or current version

These forms detail training requirements and targets and ammunition to be used during the training exercise. These forms are subject to change.

Some information has been redacted to protect personally identifiable information (PII).

(b) (4)

(b) (4)

(b) (4)

(b) (4)

(b) (4)

(b) (4)

(b) (4)

(b) (4)

(b) (4)

(b) (4)

(b) (4) (b) (4)(b) (4)

(b) (4)

(b) (4)

(b) (4)

(b) (4)

(b) (4)

(b) (4)

(b) (4)

(b) (4) (b (4

Scenario Input Guide Sheet

TURNIN DATE The date the input sheet is turned into Range Control.

DATES OF FIRE Dates that the Unit has the range to include the setup and clearing of the range.

UNIT Unit that will be using the range.

RANGE Range that the Unit is training on.

TABLE The type of training that will be done on the range.

POINT OF CONTACT The person to contact for any problems or questions with the scenario.

PHONE The phone number of the Point of Contact.

TARGET SCALE

1/10,1/4,1/2,FULL

The scale of the targets that you want to use for training.

SCENARIO #

FILE #

This section will be filled out by the scenario programmer.

ENG NO# Sequence in which the Unit will run the engagements.

TASK NO# Taken from the FM. This does not have to be in any order.

FL/FP/FB/HD Where the Unit will fire that engagement from. Firing Line, Firing

Point, Firing Box, Hull Down, Battle Position.

PRI TGT NO# The Primary Target that the unit will fire at. If a target is a Primary

Target it cannot be used as an Alternate Target in the same scenario!!

ALT TGT NO# This is the Alternate Target to be used in case the PRI TGT malfunctions. On fully computerized targets the ALT TGT is a separate step and will automatically raise if the PRI TGT malfunctions. If a target is used as an Alternate Target it can not be used as a Primary Target in the same scenario!!

TYPE OF WPNS This is the type of weapon being used.

TYPE OF AMMO The type of Ammo being used

TYPE OF TGT This is the type of target that you want to use.

EXPOS START TIME IN

SEC

When you want the target to start to raise in the engagement. If you are using multiple target type and you want them to be presented at the same time, you need to start with the target that takes the most time to raise at 0.

EXPOS DURATION IN SEC This is the amount of time that you want the target to be exposed during that engagement.

(b) (4)

Scenario Input Guide Sheet

A How the target will respond when hit.

B Hit Mode –

C Hits To Kill –

HF Hostile Fire –

HF START TIME IN SEC When do you want the hostile fire to go off.

MOVER MOVES LEFT TO

RIGHT

If you want the mover to move from left to right then place an X in this box.

MOVER MOVES RIGHT TO

LEFT

If you want the mover to move from right to left then place an X in this box.

START TIME FOR MOVER When do you want the Mover to start moving.

END TIME FOR MOVER This is the time that the Mover will stop moving during the step.

MOVER SPEED this is the speed that the mover can travel.

(b) (4)

(b) (4)

(b) (4)

(b) (4)

(b) (4)

(b

(4

(b

(4

(b

(4

(b

(4

(b

(4

(b

(4

(b

(4

(b

(4

(b

(4

(b

(4

(b

(4

(b

(4

(b

(4