0005-SRW_PWS_Basic_dated_15_NOV_2012_.docx

Performance Work Statement

For the

Army Soldier Radio Waveform (SRW) Appliqué Radio System

15 November 2012

Basic Award

Table of Contents

Scope and Introduction Scope This Performance Work Statement (PWS) defines the technical requirements for a single-channel, vehicular-mounted, software-defined radio for use by the Brigade Combat Teams (BCT). Throughout this document, this radio will be referred to as the SRW Appliqué Radio System. Radio support services necessary to enable fielding and continued field operations will also be procured.

Objective The intent of this acquisition is to buy non-developmental radio systems, and required support services, for our Warfighters as well as Federal, state and local agencies, and authorized foreign militaries. The Government will make the Government-owned Soldier Radio Waveform (SRW) available to the Contractor. The Contractor shall take the SRW and integrate it onto their hardware solution. The Contractor shall then offer to the Government Radio Systems that meet or exceed the Performance Work Statement (PWS) requirements contained herein.

Contracting Officer Representative (COR) The Contracting Officer will designate a Contracting Officer Representative COR(s) in writing and provide a copy of that letter to the Contractors. The COR letter will state the responsibilities and limitations of the COR, especially with regard to changes in cost or price, estimates, or changes in delivery dates. The COR is not authorized to change any of the terms and conditions of the contract award or delivery order.

Non-personnel Service This is a non-personnel services contract to provide Soldier Radio Waveform (SRW) Radios. The contractor, as an independent contractor and not as an agent of the Government, shall provide the necessary resources (except those furnished by the Government) to accomplish tasks of the type set forth below.

Contractor employees performing services under this contract shall be controlled, directed and supervised at all times by management personnel of the contractor. The contractor's management shall ensure that employees properly comply with the performance standards outlined in this Performance Work Statement and as required by the contracting officer or the contracting officer's representative (COR). Contractor employees shall perform independent of and without the supervision of any Government official. Actions of contractor employees may not be interpreted or implemented in any manner that results in any contractor employee creating or modifying Federal policy, obligating the appropriated funds of the U.S. Government, overseeing the work of Federal employees, providing direct personal services to any Federal employee or otherwise violating the prohibitions set forth in Parts 7.5 and 37.1 of the Federal Acquisition Regulation (FAR). The Government shall control access to the facility and shall perform the inspection and acceptance of completed work and tasks.

Organizational Conflict of Interest Contractor and subcontractor personnel performing work under this contract may receive, have access to, or participate in the development of proprietary or source selection information (e.g., cost or pricing information, budget information or analyses, specifications or work statements, etc.) or perform evaluation services which may create a current or subsequent Organizational Conflict of Interests (OCI) as defined in FAR Subpart 9.5. The Contractor shall notify the Contracting Officer immediately whenever it becomes aware that such access or participation may result in any actual or potential OCI and shall promptly submit a plan to the Contracting Officer to avoid or mitigate any such OCI. The Contractor’s mitigation plan will be determined to be acceptable solely at the discretion of the Contracting Officer and in the event the Contracting Officer unilaterally determines that any such OCI cannot be satisfactorily avoided or mitigated, the Contracting Officer may affect other remedies as he or she deems necessary, including prohibiting the Contractor from participation in subsequent contracted requirements which may be affected by the OCI.

Identification of Contractor Employee All contract personnel attending meetings, answering Government telephones, emailing and working in other situations where their contractor status is not obvious to third parties are required to identify themselves as such to avoid creating an impression in the minds of members of the public that they are Government officials. They must also ensure that all documents or reports produced by contractors are suitably marked as contractor products or that contractor participation is appropriately disclosed.

Type of Contract This will be a Multiple Award Indefinite Delivery-Indefinite Quantity (ID/IQ) type contract, for both supplies and services. This contract will support the issuance of firm fixed price (FFP) type and cost plus fixed fee (CPFF) type, and cost type delivery and task orders.

On Ramps/Off Ramps The Government reserves the right to review all contracts under SRW Appliqué Radio System Multiple Award IDIQ Contract suite annually to determine whether it would be appropriate to reissue the solicitation for the purposes of allowing for technology insertion, revising Government requirements, adding additional IDIQ holders, and/or whether or not it would be appropriate to remove existing IDIQ Contract holders. This will be done via the use of an “on and off ramp” concept.

ON RAMP

Consistent with FAR 16.504(c)(1)(ii)(A), the Contracting Officer has determined that it is in the Government's best interest that at all times during the term of the Basic Contract, there remain an adequate amount of competition under the SRW Appliqué Radio Multiple Award IDIQ Contract suite. As a result, periodically, the Contracting Officer will assess the Government’s requirements, technology available in open market, quality of the performance by each IDIQ holder, the number, value and complexity of work assigned to each holder, and the amount of competition achieved. Based on these criteria, if it is in the best interest of the Government, the Contracting Officer may conduct an “on ramp” to add additional Contract holders to this Contract provided that:

(i) Notice of an “on ramp,” containing a solicitation for Contractors to respond to, is publicized on the Army Single Face to Industry (ASFI) website;

(ii) The solicitation identifies the total approximate number of new awards that the Contracting Officer intends to make. The Contracting Officer may decide to award more or fewer Contracts than the number anticipated in the solicitation depending upon the overall quality of the offers received;

(iii) The award decision under any solicitation is based upon substantially the same evaluation factors/sub-factors as the original solicitation;

(iv) The terms and conditions of any resulting awards from a new solicitation are materially identical to the existing version of the Basic Contract;

(v) The term for any such new awards from a solicitation is co-terminus with the existing ordering period for all other Contractors;

(vi) If awarded a Contract, any new Contractor is eligible to submit a proposal in response to any RFP and receive Order awards with the same rights and obligations as any other Contractor; and

(vii) The award of any new Contract(s) does not increase the overall ceiling of the Basic Contract.

(viii) Existing Contractors shall not hold more than one Basic Contract at any time;

OFF RAMP

To ensure success of the SRW Appliqué Radio Multiple Award IDIQ Contract suite, each prime Contractor is expected to participate in the ordering process by submitting proposals, that are found to be acceptable in accordance with the requirements of the request for proposal (RFP), for which the Government determines that the Contractor has a reasonable chance for award, and to successfully perform the terms of their Orders. If a Contractor does not meet these expectations, it is the Government's intent to "off-ramp" the Contractor by:

(i) Executing a no-cost settlement in accordance with FAR 49.101(b), if applicable; or

(ii) Implementing a termination for convenience, if applicable and only if such action is in the Government's best interest; or

(iii) Implementing a termination for default, if applicable Travel Travel throughout the continental US (CONUS) and outside continental US (OCONUS), to include hazardous and isolated locations, will be required during the performance of this contract.

Period of Performance This contract shall have a five year ordering period with five one-year ordering period options.

Information Security Requirements Contractor personnel performing work under this contract must have a security clearance up to secret level at time of the proposal submission, and must maintain the level of security required for the life of the contract (to include throughout the warranty period). The security requirements are in accordance with the DD-254 associated with this contract.

In performing this contract, the contractor will have access to classified information, will receive and generate classified material and fabricate, modify and store classified hardware and software. The work performed by the Contractor will require access to unclassified, For Official Use Only (FOUO), and Secret data, information, and spaces.

The Contractor will require access to various Security or Program Classification Guide(s) (SCG), the Secret Internet Protocol Router Network (SIPRNET), and Tactical Networks. The Contractor will require a Communications Security (COMSEC) account and a Defense Technical Information Center (DTIC) account.

Operational Security (OPSEC) requirements will be provided by the Government IAW AR 530-1.

Contractor personnel performing Information Technology sensitive duties are subject to investigative and assignment requirements in accordance with AR 25-2 (Information Assurance), AR 380-67 (Personnel Security Program), and affiliated regulations.

Foreign subcontractor participation will be handled in accordance with AR 380-10 (Foreign Disclosure and Contacts with Foreign Representatives), CECOM Regulation 380-16 (Industrial Security), National Disclosure Policy, and affiliated regulations and supplements to include Directive-Type Memorandum (DTM) 09-019 - Policy Guidance for Foreign Ownership, Control, or Influence (FOCI) , September 2, 2009.

The SRW Radio System has a TEMPEST requirement.

Physical Security The Contractor shall be responsible for safeguarding all government equipment, information, and property provided for contractor use.

Threshold (t) and Objective (o) Capabilities The PWS requirements are defined as either Threshold or Objective requirements. The Threshold requirements are indicated by a “(t)” and the Objective requirements are indicated by an “(o)” in the PWS. A threshold is defined as the Government’s minimum requirement. An objective is defined as a desired performance characteristic that exceeds the minimum requirement. When an objective value is listed in conjunction with a threshold value it must be understood that the threshold value represents the minimum requirement that must be met while the objective value represents the desired performance characteristic. Objective requirements need not be met for initial contract award. The Government reserves the right to convert objectives to thresholds at the Delivery Order level.

In some cases, the Threshold (t) requirement and Objective (o) requirement are included with the intent of achieving one performance capability. For example, the Threshold requirement may be a data completion rate of 92% or better while the Objective data completion rate is 97% or better. When there is a Threshold and Objective requirement within the same performance arena, and the Contractor’s solution meets the Objective requirement, there is no requirement to also meet the Threshold requirement.

To ensure Objective requirements provide enhanced capability, there are minimum standards within the Objective requirements that the Offeror shall meet if you offer against an Objective Requirement. For example, Dismounted Radio is an Objective (o) requirement; you do not have to offer a Dismounted Radio. However, it you do offer a Dismounted Radio you shall also offer the Threshold (t) battery power source for the Dismounted Radio.

The intent of this contract is for the successful Offerors to continuously improve their SRW Radio Systems. Thus, in future fair opportunity competitions, the Contractor may choose to offer additional capabilities not currently required by this Performance Work Statement (PWS). Contractors are encouraged to offer these additional capabilities for Government consideration. However, the Government, depending upon the evaluation criteria set forth in the delivery order, may or may not elect to assign additional value to the offered capabilities.

Reference Material The following specifications and standards form a part of this document to the extent specified herein. The specifications and standards in effect at contract award shall be the revision listed in the Department of Defense Index of Specifications and Standards (DODISS) at the time of contract award. Many documents not called out herein also apply IAW the Contractor’s best practices.

Military Specifications and Documents

Ground-Based Facilities

Other Standards, Specifications, and Documents

Simple Network Management Protocol (SNMP)

Order of Precedence In the event of a conflict between documents referenced herein and the contents of this PWS, the Contractor will bring that information to the Contracting Officer’s attention in writing. The Contracting Officer will make a determination as to which document will supersede. Nothing in this PWS supersedes applicable laws and regulations unless a specific exemption has been obtained in writing by the Contract Officer.

Government Furnished Facilities, Property, Equipment and Services The Government does not intend to provide Facilities, Property, or Equipment in support of this procurement effort. However, any facilities, equipment or property to be provided will be specified at the Delivery/Task Order level. Furthermore, if the Contractor needs to obtain facilities, and/or equipment to support their development, integration, or test efforts, the Government may sponsor the Contractor to obtain that equipment through the proper channels.

Intellectual Property

(t) Government’s Rights The Government’s rights in non-commercial technical data and software deliverables are governed by the provisions of DFARS 252.227-7013 and DFARS 252.227-7014, respectively.

(t) Licenses The Contractor shall disclose any licenses and/or fees required for SRW Radio System operation at the time of proposal submission.

SRW Radio System and SRW Receiver/Transceiver This Performance Work Statement is for a single-channel, vehicular mounted, software-defined radio system. The SRW Radio System includes the SRW radio, power amplifier, software, and all ancillary equipment required to make the system operational. The SRW Radio System requirements apply to both the mounted and hand held SRW radio systems.

(t) Soldier Radio Waveform The Contractor shall obtain the Soldier Radio Waveform (SRW) from the Joint Program Executive Office (JPEO), Joint Tactical Radio System (JTRS) Information Repository (IR) (JPEO JTRS IR) via https://ir-registration.sd.spawar.navy.mil (requires PKI or ECA certificate) and follow the link that says, “If you are responding to the SRW Applique Request for Proposal (W15P7T-12-R-0059), please click here.”

The supporting requirement documents, such as the SRW Waveform Description Document (WDS) are available at the same site.

(t) SRW Radio System and Receiver/Transceiver (R/T) The SRW Radio System includes the SRW radio, power amplifier, software, and all ancillary equipment required to make the system operational. The SRW Radio System requirements apply to both the mounted and hand held SRW radio systems.

The SRW Receiver/Transceiver (SRW R/T) is the receiver/transceiver component of the SRW Radio System.

(t) UHF Transmitter Characteristics

(t) Operational Frequency Range

(t) Shall operate over the frequency ranges of 225-450 MHz UHF, with tuning increments of not greater than 25 kHz.

(o) Shall operate over the frequency ranges of 225-450 MHz UHF, with tuning increments of not greater than 12.5 kHz.

(t) Power Level

(t) Shall transmit with a power of not less than 20 Watts into a 50 Ohm load over the 225-450 MHz UHF frequency range.

(t) The radio transceiver shall be capable of operating indefinitely at a transmit duty cycle of no less than 40% at this power at all data rates.

(t) Occupied Bandwidth

(t) The 97.5% occupied bandwidth shall not exceed 1.2 MHz when operating CSMA/CA.

(o) The 99% occupied bandwidth shall not exceed 1.2 MHz when operating CSMA/CA.

(o) L-Band Transmitter Characteristics

(t) Operational Frequency Range

(t) Shall operate over the frequency ranges of 1250 - 1390MHz, with tuning increments of not greater than 25 kHz.

(o) Shall operate over the frequency ranges of 1250 - 1390MHz, with tuning increments of not greater than 12.5 kHz.

(t) Shall operate over the frequency ranges of 1755 – 1850 MHz, with tuning increments of not greater than 25 kHz.

(o) Shall operate over the frequency ranges of 1755 – 1850 MHz, with tuning increments of not greater than 12.5 kHz.

(o) Shall operate over the frequency ranges of 1850 – 2000 MHz, with tuning increments of not greater than 12.5 kHz.

(t) Power Level

(t) The radio transceiver shall be capable of operating indefinitely at a transmit duty cycle of no less than 40% at this power at all data rates.

(o) Shall transmit with a power of not less than 20 Watts into a 50 Ohm load over the operational frequency range.

(t) Occupied Bandwidth

(t) The 97.5% occupied bandwidth shall not exceed 1.2 MHz when operating CSMA/CA.

(o) The 99% occupied bandwidth shall not exceed 1.2 MHz when operating CSMA/CA.

(t) Output Power Protection The transmitter shall not be damaged by operation into a short and open circuit at the RF output connector.

(t) Receiver Characteristics

(t) Receiver Sensitivity

(t) Shall have a packet completion rate of not less than 99% at the highest combat communications data rate within received input signal level range of -88 dBm and +0 dBm.

(o) Shall operate at lower received input signal levels.

(o) Shall operate at higher received input signal levels.

(t) RF Filtering

(t) Adjacent Channel Rejection

(t) The receiver shall reject adjacent channel signals.

(t) -3 dB bandwidth shall not be greater than 3 MHz.

(t) -20 dB bandwidth shall not be greater than 7 MHz.

(t) -60 dB bandwidth shall not be greater than 11.5 MHz.

(o) Shall support narrower bandwidths than the above (t) requirements.

(t) Out of Band Interference The receiver shall be capable of operating in the presence of out of band interference at a level of -6 dBm with no more than 3 dB degradation in receiver sensitivity. Out of band interference is defined as any interferer that is offset from the chosen selected receive frequency (fo) by more than 10% of fo.

(o) Transmitter Receiver Data Output

(o) Shall provide a control word output and serial control word output stream, at a minimum providing the frequency to which the radio is tuned.

(o) Shall provide a discrete signal indicating the transmit/receive state.

(o) Receiver Performance

(o) Shall have a dynamic range of at least 90 dB.

(t) EMI & EMC Shall be compliant with the Electromagnetic Interference (EMI) and Electromagnetic Compatibility (EMC) requirements of MIL-STD-461F.

(t) CS115, CS116, CE102, CS101.

(t) CE106 - Spurious emission across the entire operational frequency range shall not be more than-65 dBc. Second and third order harmonics shall not be more than -45 dBc. The transmit mode portion of this requirement is not applicable within either the radio necessary bandwidth or plus or minus 5 % of the fundamental frequency. Test method CE106 or RE103 is acceptable.

(o) CS103 for undesired signal levels 60dB above desired signal level of paragraph 5.1.4.1.1.

(o) CS104 for undesired signal levels 80dB above desired signal level of paragraph 5.1.4.1.1 within a test range of 10MHz to 20GHz.

(t) CS114 bulk cables injection susceptibility signals shall be MIL-STD-461F, Figure CS114-1 (Curve # 3 {10 kHz to 2 MHz} & Curve # 4 {2 MHz to 30 MHz}).

(o) RS103 tested at a level of 200V/M.

(t) Shall comply with Electro Static Discharge (ESD) and charge control requirements of MIL-STD 464C.

(o) Shall withstand the effects of High Altitude Electromagnetic Pulse (HEMP) in accordance with MIL-STD 2169B.

(o) Shall be able to perform mission essential communication functions following exposure to Near Strike Lightning (NSL) events.

(t) Nuclear, Biological and Chemical (NBC)

(t) Shall be able to be operated and maintained by personnel in full Mission Oriented Protective Posture (MOPP) IV protective gear.

(o) Shall provide a capability to be decontaminated using existing standard solvents as documented in FM 3-5, NBC Decontamination dated 28 July 2000.

(t) TEMPEST Shall be TEMPEST compliant to USA NSTISSAM Level III or NSTISSAM Level II to a level sufficient to enable NSA certification for either Sensitive but UNCLASSIFIED (SBU) or SECRET data transport.

(t) Connectors and Interfaces

(t) Shall provide U-283/U, 6 pin audio or key fill connector.

(o) Shall provide battery connector and interface.

(t) Shall provide a Universal Serial Bus (USB) interface.

(t) Shall provide an Ethernet, IEEE 802.3 interface.

(t) Vehicular Power

(t) Shall draw direct vehicular power +28 VDC per MIL-STD-1275.

(t) Shall provide capability to prevent radio damage caused by battery reverse polarity.

(t) Size There are two basic installation configurations. The first configuration assumes there is a SINCGARS VAA in the vehicle where the offered SRW Radio System will fit into one half of the VAA next to an RT-1523F/G radio. The second configuration assumes no VAA and the SRW Radio System must come with a single mounting tray as part of the system.

(t) Shall meet at least one of the two below listed size/installation requirements.

Size Configuration 1

(t) Shall measure no more than 5.25“(w) x 10” (l) x 3.5” (h) (all measurements are in inches) in vehicles with SINCGARS VAA.

(t) Shall fit into one half of a SINCGARS VAA without protruding more than one inch forward of the VAA. Cables may protrude.

Size Configuration 2

(t) Shall be able to be mounted using a single mounting tray that shall measure no more than 15.9” (w) x 16.1” (l) x 9” (h) (all measurements are in inches).

(t) Environmental Testing

(t) Altitude (Low Pressure)

(t) Shall withstand low pressure storage at an altitude of 15,000 ft above sea-level in accordance with MIL-STD-810G, Method 500.5, Procedure I – Storage/Air Transport.

(t) Shall be operable at an unpressurized altitude of 15,000 ft above sea-level accordance with MIL-STD-810G, Method 500.5, Procedure II – Operation/Air Carriage.

(t) Temperature

(t) Shall operate in temperatures ranging from -30° C to +49° C verified by testing in accordance with MIL-STD-810G, Methods 501.5, Procedure II – Operation and 502.5, Procedure II – Operation.

(o) Shall operate in temperatures ranging from -30° C to +71° C, which includes a 15° C rise for the effects of solar radiation on the equipment, verified by testing in accordance with MIL-STD-810G, Methods 501.5, Procedure II – Operation and 502.5, Procedure II – Operation.

(o) Shall withstand storage temperatures ranging from -51.1° C to +71° C verified by testing in accordance with MIL-STD-810G, Methods 501.5, Procedure I – High Temperature Storage and 502.5, Procedure I – Low Temperature Storage.

(o) Rain and Blowing Rain

(o) Shall be capable of operating in 10.2 cm (4 inches) of rain per hour and 64 kph (40 mph) wind for 40 minutes verified by testing in accordance with MIL-STD-810G, Method 506.5, Procedure I – Rain and Blowing Rain.

(t) Humidity

(t) Shall operate and be impervious to humidity with relative humidity from 5% to 95% non-condensing and conditions of mist and fog as verified by testing in accordance with MIL-STD-810G, Method 507.5, Procedure I – Induced, for Non-Hazardous Item, Normal Test Duration Cycle B1.

(t) Shall survive storage in hot, humid conditions as verified by testing in accordance with MIL-STD-810G, Method 507.5, Procedure I – Induced, for Non-Hazardous Items, Normal Test Duration Induced Cycle B2.

(o) Shall operate in hot, humid conditions as verified by testing in accordance with MIL-STD-810G, Method 507.5, Procedure II – Aggravated.

(t) Fungus Shall withstand, in both operating and non-operating conditions, exposure to fungus growth as encountered in tropical climates and not support fungal growth verified by testing in accordance with MIL-STD-810G, Method 508.6 using Table 508.6-I.

(t) Salt-Fog Shall be resistant to the corrosive effects of salt-sea atmosphere verified by testing in accordance with MIL-STD-810G, Method 509.5.

(t) Sand and Dust Shall withstand exposure to fine dust particles, in wind speeds of 25 MPH (2,200 feet per minute), and sand particles, in wind speeds of 65 MPH (5,700 feet per minute), verified by testing in accordance with MIL-STD-810G, Method 510.5, Procedure I, Blowing Dust and Procedure II, Blowing Sand.

(t) Explosive Atmosphere Shall not cause ignition of the ambient explosive-gaseous air mixture verified by testing in accordance with MIL-STD-810G, Method 511.5.

(t) Vibration

(t) Shall be operational during and after undergoing vibration induced by vehicular transport (both tracked and wheeled) over all types of roads and cross country terrain and vibration associated with transportation verified by testing in accordance with MIL-STD-810G, Method 514.6, Procedure I, General vibration category 20. Additionally, there shall be no external mechanical damage.

(o) Shall be operational after undergoing vibration induced by vehicular transport (both tracked and wheeled) over all types of roads and cross country terrain and vibration associated with transportation verified by testing in accordance with MIL-STD-810G, Method 514.6, Procedure II, Loose cargo transportation category 5. Additionally, there shall be no external mechanical damage.

(t) Shock

(t) Shall be operational during and after undergoing shock verified by testing in accordance with MIL-STD-810G, Method 516.6, Procedure I – Functional Shock. Additionally, there shall be no external mechanical damage.

(t) Shall be operational after undergoing shock associated with operational service in both the HMMWV and MRAP Army ground vehicles, verified by testing in accordance with MIL-STD-810G, Method 516.6, Procedure IV – Transit Drop. Additionally, there shall be no external mechanical damage.

(t) No portion of the Vehicular mounted equipment shall break away so as to become a secondary missile that would create a hazard to personnel when subjected to crash hazard conditions, verified by testing in accordance with MIL-STD-810G, Method 516.6, Procedure V – Crash Hazard Shock Test.

(o) Ballistic Shock

(o) Shall be operational after undergoing shock associated with gunfire and direct and indirect fire experienced within an armored vehicle verified by testing in accordance with MIL-STD-810G, Method 522.1, Procedure III – Limited Spectrum Light Weight Shock Machine (LWSM).

(o) As a result of the ballistic impact, no portion of the Vehicular mounted equipment shall break away so as to become a secondary missile that would create a hazard to personnel.

(o) Temperature Shock Shall be tested in accordance with MIL-STD 810G, Method 503.5, Procedure I, and successfully pass such test.

(o) Icing/Freezing Rain Shall be tested in accordance with MIL-STD-810G, Method 521.3, and successfully pass such test.

(t) Immersion

(t) Shall be capable of being powered on and operational after immersion in at least 1 meter of seawater for 30 minutes verified by testing in accordance with MIL-STD-810G, Method 512.5, Procedure I – Immersion.

(o) Shall include a watertight battery connection that permits immediate operation after immersion in at least 2 meters of seawater for 30 minutes.

(o) Shall include a watertight RF connection that interfaces with an antenna that permits immediate operation after immersion in at least 2 meters of seawater for 30 minutes.

(t) Ancillary Capabilities, Equipment and Accessories

(t) Speaker/Microphone Shall provide handset/speaker volume control.

(t) Human Machine Interface Shall provide a human machine interface.

(t) Presets, Scanning, and Cloning

(t) Shall provide the active preset for each channel.

(t) Shall provide the operational status of the selected channel.

(t) Shall provide capability for day and night operations.

(t) Shall provide capability to select a waveform from radio memory and load it on any channel.

(t) Shall provide at least 10 presets for waveforms/modes.

(o) Shall provide at least 99 presets for waveforms/modes.

(t) Shall provide capability to program presets using government furnished tools.

(t) Clock

(t) Shall set the time-of-day within 2 seconds of operator action.

(t) Shall maintain frequency accuracy to +/- 0.5 ppm.

(o) Self Test

(o) Shall provide built-in test capabilities for detecting incorrect or insufficient input line or battery power.

(o) Shall provide built-in test capabilities for detecting incorrect radio programming.

(o) Shall provide built-in test capabilities for detecting improper channel settings.

(o) Shall provide built-in test capabilities for detecting improperly installed SRW Radio System.

(t) Interchangeability Interchangeability is defined as a condition which exists when two or more items possess such functional and physical characteristics as to be equivalent in performance and durability, and are capable of being exchanged one for the other without alteration of the items themselves, or of adjoining items.

(t) A single Contractor’s headsets/handsets, proposed for this contract, shall be interchangeable on all of that Contractor’s R/T Unit variants.

(t) A single Contractor’s handheld antenna, proposed for this contract, shall be interchangeable on all of that Contractor’s R/T Unit variants.

(t) Accessories

(t) Shall provide all necessary items to support Vehicular Mounted Operations. The Offeror shall include a complete package for installation, which includes as a minimum the following accessories:

(t) Cable(s).

(t) Handset/headset.

(o) A vehicular antenna (tri-band antenna) operating over military terrestrial VHF, UHF-FM and L-Band frequency ranges, with mounting bracket and cables.

(o) External Co-Site Mitigation Filter shall be provided as a separate part. A separate filter for each specified pass band shall be available. The co-site mitigation filter specification can be obtained from the Contracting Officer when it is required on a future Delivery Order.

(t) Waveforms, Mode Storage and Waveform Selection The required capability is a single channel radio running the Soldier Radio Waveform (SRW). Additional capabilities are desirable. Additional waveform(s) that run on that same single channel radio are desirable. Additional waveform(s) and additional channel(s) enabling simultaneous waveform operations are desirable.

(t) SRW Waveform, Mode Storage and Waveform Selection

(t) Shall support Soldier Radio Waveform (SRW). Versions will be specified in the Delivery Order. If Delivery Order does not specify an SRW version, the version documented in the Software Version Description (SDV) (CDRL 1) is acceptable. (CDRL 1).

(t) Shall store the SRW and required operational parameters.

(t) Shall conform to the applicable requirements for SRW radio interoperability with program of record SRW radio systems. (CDRL 2)

(o) Shall support Tier 1A/1B operations.

(t) Shall submit interoperability artifacts to confirm that applicable requirements have been met, demonstrating SRW radio interoperability with JTRS program of record SRW radio systems and other radio systems hosting SRW. (CDRL 2)

(o) Shall complete and provide documentation for JRIL Waveform Conformance Testing in accordance with the JTRS Compliance Memorandum. (CDRL 3)

(o) Shall complete and provide documentation for JITC Interoperability Testing in accordance with the JTRS Compliance Memorandum. (CDRL 4)

(o) Shall provide JTRS SCA Certification or complete JTRS SCA Certification in accordance with the JTRS Compliance Memorandum. (CDRL 5)

(o) Shall provide JTRS API Certification or complete JTRS API Certification in accordance with the JTRS Compliance Memorandum. (CDRL 6)

(o) Additional Waveforms

(o) Shall meet Waveform Conformance and Interoperability Standard listed in the waveform documents for all other offered waveforms.

(o) Shall store all offered waveforms and required operational parameters simultaneously.

(o) Shall allow a user to select the waveform.

(o) Shall change between any waveform or mode in less than 8 seconds.

(t) Global Positioning System (GPS)

(t) Shall be capable of receiving GPS signals over a standard interface using ICD-GPS-153 messages.

(o) Shall provide a means to exercise an option to employ an external position location system, time of day (UTC), and any associated data.

(o) Shall provide an embedded SAASM GPS.

(t) Communications Security (COMSEC)

(t) Communications Security (COMSEC)

(t) Shall provide a copy the most recent a System Verification Test Report (SVTR) on the certified baseline or the baseline for which the certification is being sought. (CDRL 20)

(o) The SRW Radio System shall not be a Controlled Cryptographic Item (CCI) when un-keyed.

(o) The SRW Radio System shall be certified by NSA for the protection of Sensitive, But UNCLASSIFIED (SBU) information. (CDRL 7)

(o) The SRW Radio System shall be certified by NSA for the protection of information up to the SECRET level. (CDRL 7)

(t) COMSEC Keying Materiel and Management For the purposes of this section, the term "keys" includes system keys, certificates, and Firefly vectors as well as user traffic keys.

(t) Shall be compatible with the Army Key Management System (AKMS) and Electronic Key Management System (EKMS) key distribution and net management systems in accordance with the Defense Information Infrastructure/Common Operating Environment (DII) / (COE) Key Management Infrastructure.

(t) Shall load unencrypted keys into the Cryptographic Subsystem via a single common fill device connector from AN/PYQ-10 Simple Key Loader (SKL).

(o) Shall load unencrypted keys into the Cryptographic Subsystem via a single common fill device connector from next generation load device provide by PEO C3T, PD COMSEC product office.

(o) Shall receive Over the Air-Rekeying (OTAR).

(o) Shall transmit OTAR.

(o) Shall support Over-the-Air-Zeroization (OTAZ).

(t) COMSEC Key Handling and Storage

(t) Shall support COMSEC key entry.

(t) Shall store all necessary keys required to operate the waveform(s).

(t) Shall provide positive confirmation following each successful key load.

(t) Shall notify the operator in the event of key load failure(s).

(t) Shall provide key status information to the operator which includes the presence or absence of a key and key type.

(t) Shall provide the operator the ability to associate keys to waveform(s)/channel(s).

(t) COMSEC Zeroization

(t) Shall provide tamper zeroization capability to zeroize all keys and erase all classified data.

(t) Shall provide a front panel zeroize panic switch on all radio systems/units. This switch shall require two discrete manual actions to zeroize all COMSEC keys.

(t) Spectrum Certification Shall provide copy of Spectrum Certification or provide a completed DRAFT DD Form 1494 using measured data. DD Form 1494, “Item 3, Stage of Allocation,” must be “d. Stage 4 – Operational.” (CDRL 8)

(t) Network Management Radio Systems operating in SRW networks must support Network Management capabilities including, but not limited to, network planning, initialization, key initialization material, initialization, configuration and reconfiguration, transfer/download of mission data, network monitoring and other network management functions.

(t) Shall consume initialization data from at least one of these IP based management tools: JTRS Enterprise Network Manager (JENM), Joint Automated Communications-Electronics Operating Instruction System (JACS)/ Automated Communications Engineering Software (ACES) and/or Soldier Radio Waveform Network Manager (SRWNM).

(o) Shall consume initialization data from all of the IP based management tools: JTRS Enterprise Network Manager (JENM), Joint Automated Communications-Electronics Operating Instruction System (JACS)/ Automated Communications Engineering Software (ACES) and/or Soldier Radio Waveform Network Manager (SRWNM).

(t) Shall provide user certificates needed for configuration.

(t) Shall support management via SNMP v3 as defined in RFC 1157, and RFC 2571, and RFC 2572, and RFC 2573, and RFC 2574, and RFC 2575, and RFC 2576.

(t) Shall support configuration fill for both Mission Files and keys via USB or other common connection directly from the Simple Key Loader (SKL) for both Mission Files and Key Materiel. Loads should take no longer than 5 minutes per radio with a 98% success rate for first try.

(t) Shall generate position location information (PLI).

(o) Shall generate position location information (PLI) in JVMF K501 (position report) format to enable communication status monitoring via Radio Based Situational Awareness Monitor (RBSAM) software embedded within Joint Capabilities Release (JCR) and Joint Battle Command- Platform (JBC-P). The frequency by which the K501 message will be sent shall be configurable over a variable range by either time or movement of the radio.

(o) Shall provide NETCONF capability to configure device IAW RFC 6241.

(o) Shall provide NETCONF templates to Government. (CDRL 9)

(t) Network Services

(t) Shall support IPv4.

(o) Shall support IPv6.

(t) Shall support either RIPv2 or OSPFv2.

(o) Shall support OSPFv2.

(t) Shall support Multicast.

(t) Shall support configuration of static multicast addresses.

(o) Shall support IGMPv2.

(o) Shall support IGMP proxy mode.

(o) Shall support IGMP responder mode.

(o) Shall support IGMP router mode.

(o) Shall support IGMPv3.

(o) Shall support PIM-SM.

(o) Shall support PIM-DM.

(o) Shall support PIM-SSM.

(o) Shall support debugging of IP protocols within the radio.

(o) Shall support logging of IP protocols within the radio.

(o) Shall support SYSLOG logging to remote SYSLOG server.

(t) Shall support static routes.

(t) Shall enable settable routing metrics.

(t) Shall enable route redistribution.

(t) Shall provide private MIBs to the Government, for use by Government and re-distribution to any Government agency and Government contractor. (CDRL 10)

(t) Shall provide a list of Public MIBs supported. (CDRL 10)

(o) Shall support SSH.

(o) Shall support QoS and TOS.

(o) Shall support TCP Explicit Congestion Notification.

(o) Shall support IP Header Compression.

(o) Shall support DSCP.

(o) Shall provide Command Line Interface (CLI).

(o) Shall support TFTP to enable download of configuration data.

(t) Operational Security (OPSEC)

(t) Shall support the government in the development of an OPSEC Plan IAW AR 530-1.

(t) Shall have a facility clearance with SECRET safeguarding capability sufficient for the maximum quantities possible under the contract delivery order award.

(t) Shall require access to COMSEC information, NATO, Foreign Government Information and FOUO information.

(t) Shall require access to Security/Program Classification Guides (SCG).

(t) Shall require access to SIPRNET.

(t) Shall require access to Government SCIF.

(t) Shall require access to classified information while overseas.

(t) Shall be authorized to use the Defense Technical Information Center (DTIC).

(t) Shall be authorized to use the Defense Courier Service.

(t) Shall have a COMSEC account.

(t) Shall perform administrative duties that will not require a clearance but may require investigation for IT duties.

(t) Performance of this contract shall be accomplished at CONUS and OCONUS locations as required by the Contracting Officer.

(t) Foreign subcontractor participation shall be handled in accordance with AR 380-10 (Technology Transfer, Disclosure of Information & Contacts with Foreign Representatives), CECOM Regulation 380-16 (Industrial Security), National Disclosure Policy, and affiliated regulations and/or supplements. (DTM) 09-019 - “Policy Guidance for Foreign Ownership, Control, or Influence (FOCI)”, September 2, 2009.

(t) DIACAP and ATO

(t) Shall provide technical support to the Government as it completes the DoD Information Assurance Certification and Accreditation Process (DIACAP) and Authority to Operator (ATO).

(t) Shall provide Security Test Results and Scans to support the DIACAP and ATO process. (CDRL 11)

(t) Shall support the government in development of the DIACAP and ATO artifacts and the development of the following documents:

(t) User Security Manual (USM)

(t) Standing Operating Procedures (SOP)

(t) System Security Plan (SSP)

(t) Incident Plan

(t) Contingency Plan

(t) Security Classification Guide (SCG) (CDRL 33)

(t) Safety Engineering and Hazard Tracking

(t) Shall enter and track hazards using a government provided electronic hazard tracking system (eHTS). The government will provide the procedure of how to gain access to the eHTS no later than 30 days after Delivery Order award.

(t) Shall update eHTS and inform the Contracting Officer within two days of identifying a High, Serious, or Medium Hazard.

(t) Shall update eHTS monthly.

(t) Shall provide a Safety Assessment Report with the proposal, thereafter, as required to update compliance via eHTS. (CDRL 12)

(o) Hand Held (HH) SRW Radio and HH SRW R/T The following requirements enables the SRW radio system to support dismounted operations via a “jerk and run” capability. When installed into a vehicular installation kit will service as a vehicular mounted SRW radio system; when operating with dismounted accessories will service as a handheld (HH) SRW radio.

(t) Shall provide HH SRW receiver/transceiver (R/T).

(t) Shall provide HH SRW radio system with all necessary accessories and ancillary items.

(t) Power Source

(t) Shall prevent radio damage caused by battery reverse polarity.

(t) Shall provide battery state of charge status information.

(o) Shall be capable of being powered by rechargeable batteries.

(t) Shall be capable of being powered by non-rechargeable batteries.

(o) Interchangeability

(o) Contractor’s batteries, proposed for this contract, shall be interchangeable on all of that Contractor’s R/T Unit variants.

(o) Contractor’s chargers, proposed for this contract, shall be interchangeable on all of that Contractor’s R/T Unit variants.

(t) Accessories

(t) GPS unit (Integrated or External) with antenna and cables.

(t) Non-rechargeable battery.

(o) Rechargeable battery. The rechargeable battery shall be compatible with LCMC/CECOM Multi-Bay AC/CD Charger; the use of a rechargeable adapter is acceptable.

(t) Dismounted radio antenna.

4.3.12.3.6 (o) Holster

(o) Handset/headset.

(o) Other accessories.

(t) Suitability and Sustainment

(t) Warranty Requirements

(t) Shall establish and maintain a failure free-type warranty performance system. All offered warranties must be separately priced. The following are the threshold and objective warranties requested:

(t) Shall include a 2-year warranty for the receiver/transceiver (R/T) and amplifier and a minimum 1-year manufacturer warranty for all accessories.

(t) Shall include a 5-year warranty for the…