TDP 2 1052000 REV - COVER CONTROLS ENCLOSURE STA 247-265.5.pdf

DISTRIBUTION STATEMENT D: DISTRIBUTION AUTHORIZED TO THE DEPARTMENT

OF DEFENSE (DoD) AND DoD CONTRACTOR'S ONLY FOR ADMINISTRATIVE AND

OPERATIONAL USE. THIS DETERMINATION WAS MADE ON 23 FEB 2012. OTHER

REQUEST SHALL BE REFERRED TO PRODUCT MANAGER (PM) AIR WARRIOR (AW).

SFAE-SDR-AW. REDSTONE ARSENAL, AL 35898-5000.

EXPORT CONTROL WARNING: THIS DOCUMENT CONTAINS TECHNICAL DATA

WHOSE EXPORT IS RESTRICTED BY THE ARMS EXPORT CONTROL ACT (TITLE

22, U.S.C. SEC 2751 ET SEQ.) OR THE EXPORT ADMINISTRATION ACT OF 1979,

AS AMENDED, TITLE 50, U.S.C., APP 2401 ET SEQ. VIOLATIONS OF THESE

EXPORT LAWS ARE SUBJECT TO SEVERE CRIMINAL PENALTIES. DISSEMINATE

IN ACCORDANCE WITH PROVISION OF DoD DIRECTIVE 5230.25

FILENAME:UNLESS OTHERWISE SPECIFIED

DIMENSIONS ARE IN INCHES.

TOLERANCES SHOWN BELOW

FRACTIONS , ANGLES 1

3 PLACE DECIMALS .010

2 PLACE DECIMALS .03

1 PLACE DECIMALS .5

APPROVED BY ORDER OF COMMANDER

USAAMCOM

SUBMITTED

ENGINEER

CHECKED

PREPARED

U.S. ARMY

AVIATION AND MISSILE COMMAND

REDSTONE ARSENAL, ALABAMA 35898

NEXT ASSY

APPLICATION SCALE:

DRAWING NO.CAGE CODESIZE

TITLE

CONTRACT NO.

DATE

USED ON

REV

THIRD ANGLE PROJECTION

APPROVED

QTY PER DASH NO.

1052000

P.ELLIS

D 81996

SHEET 1 OF 1

COVER, CONTROLS

ENCLOSURE STA 247-265.5

1:4

UH-60M1051772

2014/01/06

J.CHURCH 2014/01/06

R.DRAKE 2014/01/06

1052000

FA8075-14-D-0025

2014/01/06

2014/01/06B.KECK

REFERENCE ONLY

THIS DRAWING IS FOR REFERENCE ONLY.

NO PARTS MAY BE FABRICATED USING THIS

UNRELEASED DRAWING.

CAD MAINTAINED. CHANGES SHALL BE

INCORPORATED BY THE DESIGN ACTIVITY.

K.WIETER

-10 COVER, CONTROLS ENCLOSURE STA 247-265.5, LEFT (SHOWN) (70500-52053)

-20 COVER, CONTROLS ENCLOSURE STA 247-265.5, RIGHT (OPPOSITE) (70500-52053)

.63 1.38

2.50

6. R FULL

ALTERED ITEM DRAWING

REVISIONS

ZONE REV DESCRIPTION DATE APPROVED

- INITIAL RELEASE PER ERR AV-14214 2018/12/07 S.SANDERS

-20 -10 CAGE CODE PART OR

IDENTIFYING NUMBER NOMENCLATURE OR DESCRIPTION MATERIAL SPECIFICATION NOTES ITEM OR

FIND NO.

PARTS LIST

AR AR 1A9T3 EC1357 ADHESIVE, TYPE 1 SS9230-001 7. 1

- -20 COVER, CONTROLS ENCLOSURE STA 247-265.5, RIGHT 3. -

- -10 COVER, CONTROLS ENCLOSURE STA 247-265.5, LEFT 3. -

D

C

A

12345

D

C

B

A

1052000 D

W G

N O

MAKE FROM EXISTING COVER, CONTROLS ENCLOSURE (70500-52053).

CAGE CODE: 78286.

7. AS ALTERNATE ADHESIVE, USE ADHESIVE PER SS9230-001

6. ITEM IDENTIFICATION: OBLITERATE VENDOR'S PART NUMBER WITHOUT

DAMAGE TO PART. REIDENTIFY IAW MIL-STD-130, METHOD: RUBBER STAMP

WITH.13 HIGH CHARACTERS USING AA56032-I INK (CONTRASTING COLOR)

IAW A-A-56032. LOCATE APPROXIMATELY AS SHOWN. AT A MINIMUM PART

MARK AS FOLLOWS: 81996ASSY1052000-XX (WHERE-XX IS THE DASH NO.)

MFR CAGE CODE (IF DIFFERENT FROM DESIGN ACTIVITY)

5. MODIFICATION INSTRUCTIONS:

A. RETAIN ENOUGH MATERIAL IN THE CUTOUT AREA TO ALLOW CLOTH

TO BE FOLDED BACK OVER EXPOSED EDGES OF COVER.

B. BOND EXCESS FABRIC TO COVER USING ADHESIVE (EC1357)

PER MMM-A-101, EC 1357 NEOPRENE HIGH PERFORMANCE CONTACT

ADHESIVE.

4. WRINKLES AND/OR DISTORTIONS ARE ACCEPTABLE IN THE FINISHED

PART IF THEY ARE NO MORE THAN THREE TIMES THE THICKNESS OF

THE FACE CLOTH.

3.

2. REMOVE BURRS AND BREAK ALL SHARP EDGES.

APPLICABLE STANDARDS/ SPECIFICATIONS:1.

INTERPRET DRAWING IAW ASME Y14.100-2013.

DIMENSIONING AND TOLERANCING IAW ASME Y14.5-2009.

ABBREVIATIONS AND ACRONYMS IAW Y14.38.

NOTES: UNLESS OTHERWISE SPECIFIED