SF241-0019.pdf

Standard Form PDF 48 KB Posted

Attached to
Resonator Laser Gyro
Solicitation number
SF241-0019
Issued by

About this file

This document is a U.S. Space Force Small Business Innovation Research (SBIR) solicitation for SF241-0019: Resonator Laser Gyro. The objective is to develop a high-accuracy navigation attitude system for use in proliferated space constellations with smaller space vehicles. Current MEMS gyroscopes lack the required performance for precision operation in small spacecraft, while a navigation-grade gyro with MEMS-equivalent size, weight, and power characteristics would enable precision pointing and support both laser communication terminals and hosted sensor payloads on gimbaled assemblies. The technology areas include Sensors and Space Platforms, with Space Technology identified as the modernization priority.

The project focuses on developing a nanophotonic ring laser gyro (RLG) operating at an exceptional point where gain and loss are balanced, leveraging parity-time (PT) symmetry to overcome limitations of short optical path lengths. Performance targets include an Angle Random Walk (ARW) of 0.005 deg/rt-hr, bias stability of 0.05 deg/hr at 30 minutes constant temperature, dynamic range up to 10 deg/s, scale factor nonlinearity less than 10 ppm, and a form factor of one cubic inch with 1 W per active channel power consumption. Phase I requires a chip-level PT-symmetric RLG design demonstrating 50% of static environment performance with flight-representative sensor form factor and brass board electronics. Phase II must deliver a complete performance-requirement-satisfying sensor with enhanced error models and supporting electronics mountable on a 24-inch rate table. Phase III involves dynamic testing in actual environments with DC rate, AC rate, and temperature variations, with testing available at The Aerospace Corporation if needed. The CMMC level requirement is N/A, and no Technical Point of Contact is listed.

View the file

Other versions and copies of SF 241

File Revision Posted Attached to
SF241-0020.pdf Revision not stated Trusted Automated Satellite Operations for Mission Life
SF241-0023.pdf Revision not stated Low Latency Space Object Maneuver Detection
SF241-0024.pdf Revision not stated Evaluating Data Strategies in Training AI Solutions for Space C2
SF241-0017.pdf Revision not stated Satellite Cyber Immune Response to Evolving Threats
SF241-0022.pdf Revision not stated Ultra-Broadband High-Definition High-Frame Rate NIR-MWIR Imager
SF241-0021.pdf Revision not stated Optical Interconnects for High-Speed High-Efficiency Intra-satellite Data Transfer in the Space Environment
SF241-0016.pdf Revision not stated Numerical Simulation of VLF Antennas in Space Plasma
SF241-0018.pdf Revision not stated Mitigating Negative Effects of Polysulfide Dissolution in 18650 Lithium Sulfur Battery
SF241-0013.pdf Revision not stated Planar Hyperspectral Imager
SF241-D024.pdf Revision not stated 15 SPSS Path to Production Development for Electro-Optical Sensor Scheduling Software Modernization
SF241-0015.pdf Revision not stated Securely Operating Through 5G for Enterprise Space Data Transport Applications
SF241-D026.pdf Revision not stated Digital Spaceport of the Future
SF241-0025.pdf Revision not stated Modernizing USSF BMT
SF241-D023.pdf Revision not stated Automated MBSE Model Generation of Space Systems
SF241-D025.pdf Revision not stated Alternative Position, Navigation, and Timing
SF241-0014.pdf Revision not stated MUOS SATCOM Simulator Connectivity Over IP
Show all 16

Who attaches SF 241

On GovTribe

Work with this file

  • Download the original file
  • Contacts named in this file
  • Similar government files
  • Ask GovTribe AI about this file

Text version

SF241-0019: Resonator Laser Gyro

PROJECTED CMMC LEVEL REQUIREMENT:

N/A

TECHNOLOGY AREAS:

Sensors | Space Platforms

MODERNIZATION PRIORITIES:

Space Technology

KEYWORDS:

ring laser gyro; distributed constellations; nanophotonic system; precision pointing; Gyroscope, GNC (Guidance, Navigation, & Control), RLG (Ring Laser Gyro), MEMS (micro electro-mechanical), gimbal, attitude control, Sagnac effect

ADDITIONAL INFORMATION

N/A

OBJECTIVE:

The U.S. Space Force (USSF) will require high accuracy navigation attitude systems for use in proliferated constellations with smaller space vehicles. Current low mass micro electro-mechanical (MEMS) gyroscopes do not have the required performance to allow precision operation in small space vehicles. A gyroscope with MEMS size weight and power but with high navigation-grade performance would enable precision pointing of small space vehicles. Small high-grade gyros would also have applications in counterspace uses both for offensive and defensive efforts. Laser communication terminals and hosted sensor payloads would benefit from low mass rate sensors on the gimbaled assembly.

DESCRIPTION:

There is an ongoing effort to leverage unique advantages in gyro sensitivity versus size when an optical system is operated at what is termed an exceptional point. The exceptional point in a nanophotonic system which occurs when the gain and loss are balanced. The resulting operational singularity radically changes the behavior of the optical system and creates large changes in system response to external stimulus. A macro scale ring laser gyro (RLG) has sensitivity that is highly dependent on the optical ring resonator loss and the enclosed path length that the light travels. Operation of a nano scale RLG at an exceptional point promises to overcome the limitations of the very short optical path length. Utilization of the behavior singularity at the exceptional point is only possible due to recent developments in exploiting gain/loss properties in nano scale waveguides. To develop a nano scale RLG which operates at the exceptional point, you first need a nano scale RLG which operates in the standard regime of parity-time (PT) symmetry. Once that is achieved, the design can be manipulated to reach the point where parity-time symmetry breaks down and operation is at the exceptional point. This effort supports development of the PT-symmetry chip level RLG as well as error modeling for a future RLG operating at the exceptional point. The project will attempt to leverage advances in gyro technology to enable better than navigation grade performance from a single channel gyro with a one cubic inch volume. The final design should target 1 W per active channel for power consumption. The technology employed will need to be radiation hardened in the future. Target ARW is 0.005 deg/rt-hr. Bias stability at constant temperature target is 0.05 deg/hr at 30 minutes. The gyro dynamic range will be up to 10 deg/s. Performance must be maintained through TBD g acceleration in any orientation relative to the gyro sensing axis. Gyro scale factor nonlinearity from 1 deg/sec to 10 deg/sec magnitude will be less than 10 ppm after any compensation. The SF error of between +1 deg/sec and -1 deg/sec will be 0.036 deg/hr. The SF spec is 2-sigma. These performance goals are very challenging for the sensor size and could be reconsidered if the technology demonstrates promise in initial prototypes.

PHASE I:

Phase I will produce a design for a chip level phase-time (PT) symmetric ring laser gyro (RLG). Further investigation into what is required to push the design to the exceptional point will be done. While the concept of an RLG operating in the mode is still at an early stage of development, it is desired to assess the practical aspects of operational use of the device. For example, operation at the exceptional point (EP) requires high bandwidth servos to assess where is the EP is and to keep the gyro at that point. Behavior on either side of the EP is drastically different than at the singularity itself. Models should be developed to assess expected instrument output in the presence of EP control loop error. Temperature sensitivity could be quite high. Models should be developed to assess required temperature stability of the nano-optical substrate needed to maintain EP operation. Phase I will design a sensor which demonstrates 50% of the required static environment performance. Brass board electronics without flight representative size are acceptable. The sensor form factor will be flight representative. Meeting the 50% static performance goal with a 1 ci sensor volume is a challenging task and will enable assessment of the technology’s suitability to meet the higher performance goals. Error models of the sensor shall be presented which show a path to the target static and dynamic performance.

PHASE II:

Phase II will produce a sensor which satisfies the complete performance requirement. Error models described in Phase I would be enhanced to account for measured characteristics of the functional device. The supporting electronics should be small enough at the end of Phase II to be able to be mounted on a 24” rate table platter to facilitate dynamic testing. Error models should be sufficiently developed to be able to provide a realistic prediction of gyro noise, gyro bias stability, and scale factor non-linearity.

PHASE III DUAL USE APPLICATIONS:

The prototype gyro and Phase II electronics will be tested in an actual dynamic environment with DC rate, AC rate, and reasonable temperature diurnal. The data will be used to validate behavioral models from Phase II. Testing of this type can be performed at The Aerospace Corporation if the small business does not have suitable facilities.

REFERENCES:

Mercedeh Khajavikhan, Yuzhou (Nathan) Liu & Mohammad Hokmabadi (USC), Alex Schumer (TU Wien), Ardy Winoto & Gloria Hoefler (Infinera), Demetrios Christodoulides (UCF-CREOL), “Parity-Time Symmetric Ring Laser Gyroscopes”

1.

J. Ren, H. Hodaei, G. Harari, A. U. Hassan, W. Chow, M. Soltani, D. Christodoulides, M. Khajavikhan, “Ultrasensitive micro-scale parity-time-symmetric ring laser gyroscope,” Optics Letters, Vol. 42, Issue 8, pp.

1556-1559, (2017), https://doi.org/10.1364/OL.42.001556

2.

TECHNICAL POINT OF CONTACT (TPOC):

None

File details come from the government source that posted it. Updated .