Attachment a SPECIFICATIONS and sTANDARDs Applicable Documents
The following documents, in either the exact issue cited or the latest issue, shall be used to the extent specified herein.
All Specifications listed and subsequent Revisions/additions to said Specifications shall apply to this Contract.
Issues of Documents
Unless a specific date of issue or revision is cited, the following documents of the issue in effect, according to the current Government Index of Specification and Standard (GISS) so specified in the Solicitation, form a part of this SOW to the extent specified herein. Where the requirements of these documents conflict with the instructions herein, the requirements of the SOW shall govern.
Government Standards, Specifications, Handbooks, and Other Documentation Occupational Safety and Health Act of 1970
| Public Law 91-596 |
| OSHA Standard |
| CFR 1910 |
| OSHA General Industry Safety and Health Standards |
| CFR 1926 |
| OSHA Construction Standards |
| CFR Part 61 |
| OSHA National Emission Standards for Hazardous Air Pollutants |
| CFR Part 761 |
| EPA Final Rule |
National Security Agency (NSA)
| NITISSAM TEM – 2-95A dated 2/3/200 |
| RED/BLACK Installation Guidance |
| NSTISSI 7003 |
| Protected Distribution Systems (PDS) |
Available to the public via the Internet Rural Utilities Service (RUS)(formerly REA, Rural Electrification Administration) Copies of these publications may be obtained from the Rural Utilities Service, U.S. Department of Agriculture, Washington, DC 20250.
| REA Bulletin 3456 |
| PC2 Standard for Splicing Plastic Insulated Cable |
| REA Bulletin 345-50 |
| Specification for Trunk Carrier Systems, PE-60 |
| REA Bulletin 345-66 |
| Specification for Subscriber Carrier Systems, PE-64 |
| REA Bulletin 34572 |
| Specification for Filled Splice Cases, PE-74 |
| REA Bulletin 345-83 |
| Specification for Gas Tube Surge Arrestor, PE-80 |
| REA Bulletin 345-90 |
| Specification for Totally Filled Fiber-Optic Cable |
| REA Bulletin 345-150 |
| Specifications and Drawings for Construction of Direct Buried Plant |
| REA Bulletin 345-151 |
| Specifications and Drawings for Conduit and Manhole Construction |
| REA Bulletin 345-152 |
| Specifications and Drawings for Under-ground Cable Installation |
| REA Bulletin 345-153 |
| Specifications and Drawings for Construction of Pole Lines and Aerial Cable |
| REA Bulletin 345-154 |
| Specifications and Drawings for Service Entrance and Station Protector Installation |
Telephone Engineering & Construction Manual (TE&CM).
| Section 635 |
| Construction of Aerial Cable Plant |
| Section 641 |
| Construction of Buried Plant |
| Section 643 |
| Underground Conduit and Manhole Design and Construction |
| Section 644 |
| Design and Construction of Underground Cable |
| Section 815 |
| Electrical Protection of Aerial Cable |
| Section 817 |
| Electrical Protection by Effective Grounding of Cable Shields |
| Section 958 |
| Digital Cross-Connect and Drop and Insert System |
| Standard PC2 |
| Splicing Plastic-Insulated Cable |
| Standard PC4 |
| Acceptance Test & Measurement of Telephone Plant |
Miscellaneous
| DCAC 370-160-3 |
| Site Survey Data Book for Communication Facilities |
| FED-STD-1037C |
| Telecommunications: Glossary of Telecommunication Terms. |
| FIPS 17-1, 1996 |
| Federal Building Telecommunications Cabling Standard |
| FIPS 175, 21 Aug 92 |
| Federal Building Standard for Telecommunication Pathways and Spaces. |
ICEA S-80-576, 1988
Standard for Telecommunications Wire and Cable Services for Wiring of Premises
| 29CFR1910.268 |
| Telecommunication Standards |
Non-Government American National Standards Institute, Inc. (ANSI) Standards Copies of these documents may be obtained from the ANSI sales department, 1430 Broadway, New York, NY 10018.
| ANSI/ASQC A3-1987 |
| Quality System Terminology |
| ANSI/ASQC Q1-1986 |
| Generic Guidelines for Auditing of Quality Systems |
| ANSI/ASQC Q90-1987 |
| Quality Management and Quality Assurance Standards - Guidelines for Selection and Use |
| ANSI/ASQC Q91-1987 |
| Quality Systems - Model for Quality Assurance in Design/Development, Production, Installation, and Servicing |
| ANSI/ASQC Q92-1987 |
| Quality Systems - Models for Quality Assurance in Production and Installation |
| ANSI/ASQC Q93-1987 |
| Quality Systems - Models for Quality Assurance in Final Inspection and Test |
| ANSI C21984 |
| National Electrical Safety Code |
| ANSI T1.605-1991 |
| Telecommunications/Integrated Services Digital Network (ISDN)/Basic Access |
| ANSI T1.606 |
| Telecommunications - ISDN – Architectural Framework and Service Description for Frame- Relaying Bearer Service (Network to Network Interface Requirements) (ECSA) |
| ANSI X3.139-1987 |
| Fiber Distributed Data Interface (FDDI)- Token Ring Media Access Control (MAC) |
| ANSI X3.148 |
| Fiber Distributed Data Interface, Physical Layer Protocol (FDDI-PHY) |
| ANSI X3.166 |
| Fiber Distributed Data Interface, Physical Media Dependent (FDDI-PMD) |
| ANSI X3.4-1986 |
| 7 Bit American National Standard Code for Information Interchange (ASCII) |
| ANSI Y32.91972 |
| Graphic Symbols for Electrical Wiring and Layout Diagrams Used in Architectural and Building Construction |
| ANSI Y32.21-1976 |
| Graphic Symbols for Grid and Mapping Diagrams and in Cable Television System (NCTA 006-0975) |
| ANSI/EIA S-84-608 |
| Filled, Polyolefin Insulated, Copper Conductor Telecommunication Cable Technical Requirements |
| ANSI/EIA S-85-625 |
| Aircore, Polyolefin Insulated, Copper Conductor Telecommunication Cable Technical Requirements |
Bellcore Documents Copies of these publications/documents maybe obtained from Bellcore Register Information Exchange Management, PO Box 1910, 445 South Street Room 2J-125, Morristown, NJ 07962-1910, telephone (201) 829-5027/(201) 829-4785.
| TRTSY000100 |
| Pick Filled ASP Cable |
| TRTSY000101 |
| Aircore PIC ALPETH Cable |
| TRTSY000102 |
| PIC Self Support Cable |
| TRTSY000106 |
| Underground Foam-Skin PIC Bonded STALPETH |
| TRTSY000107 |
| PIC Bonded PASP Cable |
| TRTSY000108 |
| PIC Reinforced Self Support Cable |
| TRTSY000109 |
| Pick Filled Screened ASP Cable |
| TRTSY000111 |
| PIC Riser Cable |
| TRTSY000112 |
| PIC Bonded Screened PASP Cable |
| TRTSY000113 |
| PIC PAP Cable |
| TRTSY000114 |
| PIC Screen PAP Cable |
| TRTSY000118 |
| Cable Outer Protection |
| TRTSY000119 |
| Pick Filled Bonded ASP Cable |
| TRNWT000121 |
| Generic Requirements for One Pair Aerial Service Wire |
| TRNWT000122 |
| Generic Requirements for Multiple Pair Aerial Service Wire |
| TR-NWT-000123 |
| Generic Requirements for Single Pair Buried Distribution Wire |
| TR-NWT-000124 |
| Generic Requirements for Multiple Pair Buried Wire |
| TA-TSY-000130 |
| Customer Premises Cross-Connecting Wire |
| TR-NWT-000131 |
| Generic Requirements for Network Plenum Cable/Wire |
| TA-TSY000136 |
| Distributing Frame Wire |
National Fire Protection Association (NFPA) Copies of this standard may be obtained from the Nation Fire Protection Association, Battery March Park, Quincy, MA 02269, telephone (800) 344-3555.
| NFPA No. 70, 1997 |
| National Electrical Code. |
Electronic Industry Association (EIA)/Telecommunications Industry Association (TIA) Standards
Copies of the following standards may be obtained from the Electronic Industries Association/Telecommunications Industry Association, 2001 I Street, NW, Washington, DC 20006, telephone (202) 457-4966.
| EIA-232-E, Jul 1991 |
| Interface Between Data Terminal Equipment and Data Circuit-Terminating Equipment Employing Serial Binary Data Interchange |
| EIA-310-D, 1992 |
| Racks, Panels, and Associated Equipment |
| EIA472, 1985 |
| Generic Specification for Fiber-Optic Cables |
| EIA472C, 1993 |
| Sectional Specification for Fiber-Optic Communication Cables for Indoor Use |
| EIA492, 1987 |
| Generic Specification for Optical Waveguide Fibers |
| EIA/TIA-568-B |
| Commercial Building Telecommunications Wiring Standard |
| EIA/TIA-569 |
| Commercial Building Standard for Telecommunication Pathways and Spaces |
| EIA-530 |
| High Speed 25 Position Interface for Data Terminal Equipment and Data Circuit Terminating Equipment - Including Alternative 26 Position Connector |
| EIA/TIA-606 |
| Telecommunications Infrastructure of Commercial Buildings |
| EIA/TIA-607 |
| Commercial Building Grounding and Bonding Requirements for Telecommunications |
| EIA/TIA-526-14 |
| Optical Power Loss Measurements of Installed Multimode Fiber Optic Cable Plant |
| EIA TSB 36, 1991 |
| Additional Cable Specifications for Unshielded Twisted-Pair Cable |
| EIA TSB 40, 1992 |
| Additional Transmission Specifications for Unshielded Twisted-Pair Connecting Hardware |
| EIA TSB 67 |
| Transmission Performance Specifications for Field-Testing of Unshielded Twisted Pair Cabling Systems |
| EIA TSB 72 |
| Centralized Optical Fiber Cabling Guidelines |
| EIA RS232 |
| Interface Between Data Terminal Equipment and Data Communications Equipment Employing Serial Binary Data Interchange |
| EIA RS232C |
| Interface Between Data Terminal Equipment and Data Circuit-Terminating Equipment Employing Serial Binary Data Interchange |
| RS-403-73 |
| Precision Coaxial Connection for CATV Application (75 ohms) |
| RS422 |
| Electrical Characteristics of Balanced Voltage Digital Interface Circuits |
| RS423 |
| Electrical Characteristics of Unbalanced Voltage Digital Interface Circuits |
| RS440 |
| Fiber-Optic Connector Terminology |
| RS449 |
| Interface Between Data Terminal Equipment and Data Communications Equipment Employing Serial Binary Data Interchange |
| RS455 |
| Standard Test Procedures for Fiber-Optic Fibers, Cables, Transducers, Connecting and Terminating Devices (with appropriate addenda) |
| RS458A |
| Standard Optical Waveguide Fiber Material Classes and Preferred Sizes |
Institute of Electrical and Electronics Engineers, Inc. (IEEE) Copies of these documents may be obtained from IEEE Service Center, 445 Hoes Lane, Piscataway, NJ 08855-1331, telephone (800) 678-4333/(908) 981-0060.
| IEEE3151975 |
| Graphic Symbols for Electrical and Electronic Diagrams |
| IEEE315A1994 |
| Supplement to Graphic Symbols for Electrical and Electronic Diagrams |
| IEEE 802.7, 1988 |
| Broadband Local Area Network Recommended Practices |
Underwriters Laboratories, Inc. (UL) Publications
| UL 444 |
| UL Standard for Safety Communications Cables |
| UL 467 |
| Grounding and Bonding |
| UL 478, 1984 |
| Information Processing and Business Equipment |
| UL 497A |
| Protectors for Communication Circuits |
| UL 910, 1991 |
| Test Method for Fire and Smoke Characteristics of Electrical and Optical Fiber Cables Used in Air Handling Spaces |
| UL 1283 |
| Electromagnetic Interference Filters |
| UL 1449 |
| Transient Voltage Surge Suppressors |
International Telecommunications Union-Telecommunications Standardization Sector ITU-TS), formerly the International Telegraph and Telephone Consultative Committee (CCITT)
Copies of these publications may be obtained from the National Technical Information Service (NTIS) at: U.S. Department of Commerce, National Technical Information Service, 5285 Port Royal Road, Springfield, VA 22161, telephone (703) 487-4650.
| ITU-TS X.25 |
| Interface Standard |
| ITU-TS I.361 |
| Broadband-Integrated Services Digital Network (B-ISDN) ATM Layer Specification(Recommendation I.361) |
National Cable Television Association (NCTA) Engineering Standards NCTA Recommended Practices for Measurements on Cable Television Systems, Supplemented 1985
| NCTA 0002-0267 |
| CATV Amplifier Distortion Characteristics |
| NCTA 006-0975 |
| Standard Graphic Symbols for CATV |
International Standards Organization (ISO) Copies of these documents may be obtained from the American National Standards Institute Sales Department, 1430 Broadway, New York, NY 10018.
| ISO 8802/3, 21 Sep 90 |
| Information Processing Systems - Carrier Sense Multiple Access with Collision Detection Access Method and Physical Layer Specifications |
| ISO 9314-1, 15 Apr 89 |
| Information Processing System - Fiber Distributed Data Interface (FDDI) Part 1: Token Ring Physical Layer Protocol |
| ISO 9314-2, 1 May 89 |
| Information Processing Systems - FDDI Part2: Token Ring Media Access Control (MAC) Protocol |
| ISO 9314-3, 20 Apr 89 |
| Information Processing Systems - FDDI Part3: Physical Layer Medium Dependent (PMD) |
ATM Forum Specifications Copies of these documents may be obtained from the ATM Forum World Headquarters, 2570 West El Camino Real, Suite 304, Mountain View, CA 94040-1313, telephone (415) 949-6700.
| Physical Layer, as of Oct 96 |
| ATM Physical Medium Dependent Utopia Level.1 v.2.01 |
Utopia Level 2.v.1.0
| Physical Interface Spec. for 25.6 Mb/s over TP |
| ATM Physical Medium Dependent Interface Spec for 155 Mbps over TP DS1 Physical Layer Spec Utopia Level 1 v 2.01 Mid-range Physical Layer Spec for Category 3 UTP 6,312 Kbps UNI Spec E3 UNI Utopia Level 2 v 1.0 Physical Interface Spec. for 25.6 Mb/s over A Cell-based Transmission Convergence Sublayer for Clear Channel Interfaces 622.8 Mb/s Physical Layer 155.52 Mb/s Physical Layer Spec for Category 3 UTP Interface Spec. for 155 Mb/s over TP DS3 Physical Layer Interface Spec E-1 |
BICSI – Building Industry Consultant Services International Copies of these documents may be obtained from the BICSI, 8610 Hidden River Pkwy., Tampa, Florida 33637
| BICSI |
| Telecommunications Distribution Manual |
Drawings Government Index of Specifications and Standards (GISS) All Federal, military, and recognized industry specifications, standards, and related standardization documents, referenced are contained in the Department of Defenses Index of Specifications and Standards (July 1, 1996) and the Federal ADP and Telecommunications Standards Index. These indices are available from the U.S. Government Printing Office.
