RV_Medeia_Paint_Specification.docx
DOCX document 13 KB Posted
- Solicitation number
- ADF&G ITB # 2027-1100-0088 - RV Medeia Shipyard Services FY27
- Issued by
- Alaska
About this file
This is a coating (paint) specification sheet for the R/V Medeia vessel, prepared by PPG/Ameron Protective & Marine Coatings as of August 7, 2026. The specification covers surface preparation and coating application for two distinct service environments: above-waterline atmospheric surfaces including hull topsides, superstructure, deckhouse, and weather decks; and below-waterline immersed surfaces on the underwater hull. The specification establishes minimum surface preparation standards requiring solvent cleaning to SSPC-SP1 followed by abrasive blasting to SSPC-SP6/NACE No. 3 for above-waterline bare mild steel and SSPC-SP10/NACE No. 2 for below-waterline surfaces. Application must occur when substrate temperature is at least 5°F above dew point with relative humidity below 85%, and all work shall conform to current PPG/Ameron Product Data Sheets. Dry film thickness (DFT) measurements must follow SSPC-PA 2 standards, and application records documenting ambient conditions, DFT readings, and batch numbers must be maintained throughout the project.
System A for above-waterline surfaces specifies six coats comprising a Dimetcote 302 H inorganic zinc primer (2.0–4.0 mils), an Amercoat 235 phenalkamine epoxy stripe and mist-tie coat, two Amercoat 235 intermediate coats in contrasting colors (4.0–6.0 mils each), and two PSX 700 engineered siloxane finish coats (3.0–5.0 mils each), yielding a nominal system DFT of approximately 16–24 mils. System B for below-waterline surfaces prohibits inorganic zinc primers and instead specifies two Amercoat 235 anticorrosive coats (4.0–6.0 mils each in contrasting colors) applied to near-white blasted steel, followed by two ABC 3 tin-free self-polishing antifouling coats (4.0–6.0 mils each), with a boottop section using Amercoat 235 anticorrosive with an atmospheric finish. Recoat windows and cure times are specified for each product, with Dimetcote 302 H requiring a minimum of 1.5 hours and maximum of 3 months, Amercoat 235 requiring a minimum of 4 hours and maximum of 30 days, and ABC 3 requiring a minimum of 5 hours. The specification requires contrasting colors for all intermediate and anticorrosive coats to enable visual verification of coverage and addresses non-skid requirements for decks and walking surfaces through separate specification.
View the file
Other files
Show all 49
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
COATING (PAINT) SPECIFICATION SHEET
R/V MEDEIA
PPG / Ameron Protective & Marine Coatings
| Vessel |
| R/V Medeia |
| Date |
| August 7, 2026 |
| Coating supplier |
| PPG / Ameron (PMC) |
| Spec rev. |
| Draft 1 |
| Application method |
| Airless spray (brush/roll for stripe & touch-up) |
| DFT gauge |
| Per SSPC-PA 2 |
1. Scope Covers surface preparation and coating build for the R/V Medeia across two service environments: (A) above-waterline atmospheric surfaces — hull topsides, superstructure/deckhouse, and weather decks; and (B) below-waterline immersed surfaces — the bottom / underwater hull. All preparation, mixing, thinning, application, and cure shall conform to the current PPG/Ameron Product Data Sheets (PDS), which govern in case of conflict with this summary.
Product identification note: “Ameron 302” is specified here as Dimetcote 302 H (Ameron/PPG reinforced inorganic-zinc primer) — PPG’s zinc-primer line. Confirm before issue if a different product was intended.
2. Surface Preparation Standards Governing rule: surface preparation follows the minimum requirements of the applicable Ameron PDS. Solvent-clean all surfaces to SSPC-SP1 (remove oil, grease, salts) before any mechanical prep. Remove weld spatter, round sharp edges, and grind smooth per SSPC-SP2/SP3 as needed.
| Condition |
| Standard (per Ameron PDS minimum) |
Bare mild steel above waterline (under Dimetcote 302 H) SSPC-SP6 / NACE No. 3 (Commercial Blast) minimum; angular anchor profile 1.5–3.0 mils (5.0 mils max). Near-white SSPC-SP10 recommended on new steel for best service life.
Bare mild steel below waterline (under Amercoat 235, immersion) SSPC-SP10 / NACE No. 2 (Near-White Blast); angular anchor profile 2.0–4.0 mils — required for immersion / tank-lining service per Amercoat 235 PDS.
Disturbed / damaged / previously-coated areas SP1 solvent-clean, then restore to the original prep standard by spot abrasive blast where feasible. Where blasting is not feasible, power-tool clean to bare metal to SSPC-SP11 (produces a surface profile). Feather / abrade the edges of surrounding sound coating and remove all dust and residue before recoating.
3. Application & Environmental Conditions
1. Substrate temperature at least 5°F (3°C) above the dew point and rising during application and cure.
1. Relative humidity below 85%; do not apply to damp or contaminated surfaces.
1. Observe each product’s minimum/maximum application and substrate temperatures per its PDS. Dimetcote 302 H (inorganic zinc) requires ambient moisture to cure fully before topcoating.
1. Verify DFT of each coat per SSPC-PA 2 before applying the next.
4. System A — Above-Waterline (Topsides, Superstructure, Decks)
| # |
| Coat / Step |
| Product |
| Generic Type |
| DFT/coat (mils) |
| Notes |
| 1 |
| Primer (DTM) |
| Dimetcote 302 H |
| Inorganic zinc |
| 2.0–4.0 (3.0 target) |
| Applied direct to prepared bare steel. |
| 2 |
| Stripe / mist-tie coat |
| Amercoat 235 |
| Phenalkamine epoxy |
| Brush (not in nominal DFT) |
| Brush-apply to welds, edges, corners, bolt heads. Mist-coat/full-coat technique over the inorganic zinc to minimize bubbling/pinholing (per 235 PDS). |
| 3 |
| Intermediate coat 1 |
| Amercoat 235 |
| Phenalkamine epoxy |
| 4.0–6.0 |
| Color A. |
| 4 |
| Intermediate coat 2 |
| Amercoat 235 |
| Phenalkamine epoxy |
| 4.0–6.0 |
| Color B — contrasting with Color A for full-coverage verification. |
| 5 |
| Finish coat 1 |
| PSX 700 |
| Engineered siloxane |
| 3.0–5.0 |
| Per finish color schedule. |
| 6 |
| Finish coat 2 |
| PSX 700 |
| Engineered siloxane |
| 3.0–5.0 |
| Final finish color. |
Nominal system DFT: approx. 16–24 mils (excluding stripe coat).
Recoat windows (≈70–75°F): Dimetcote 302 H — min 1.5 h, max 3 months (power-wash before topcoating). Amercoat 235 — min 4 h, max 30 days over itself (abrade if exceeded). PSX 700 — min 3 h (20°C), max unlimited.
5. System B — Below-Waterline (Bottom / Underwater Hull) Do NOT use inorganic zinc (Dimetcote 302 H) below the waterline or under antifouling. Zinc-silicate primers are not recommended for continuous immersion beneath antifoulings. Use an epoxy anticorrosive barrier (Amercoat 235), which is an approved undercoat for ABC 3 antifouling.
| # |
| Coat / Step |
| Product |
| Generic Type |
| DFT/coat (mils) |
| Notes |
| 1 |
| Stripe coat |
| Amercoat 235 |
| Phenalkamine epoxy |
| Brush (not in nominal DFT) |
| Brush edges, welds, and seams before full coats. |
| 2 |
| Anticorrosive 1 |
| Amercoat 235 |
| Phenalkamine epoxy |
| 4.0–6.0 |
| Color A. Applied to near-white blasted steel. |
| 3 |
| Anticorrosive 2 |
| Amercoat 235 |
| Phenalkamine epoxy |
| 4.0–6.0 |
| Color B — contrasting for coverage verification. |
| 4 |
| Antifouling 1 |
| ABC 3 |
| Tin-free self-polishing antifouling |
| 4.0–6.0 |
| Over cured Amercoat 235 (within 235 max recoat, or abrade). |
| 5 |
| Antifouling 2 |
| ABC 3 |
| Tin-free self-polishing antifouling |
| 4.0–6.0 |
| Contrasting / signal color. |
Nominal system DFT: approx. 16–24 mils (excluding stripe coat).
Recoat windows (≈70–75°F): Amercoat 235 — min 4 h. ABC 3 — min 5 h over itself; over 235 within the 235 maximum recoat window (abrade if exceeded). Observe launch (dry-to-immersion) time per the ABC 3 PDS.
Boottop / waterline band: use the Amercoat 235 anticorrosive with an appropriate atmospheric finish (PSX 700), or a dedicated boottop finish, per the yard’s color scheme.
6. General Notes
1. Colors: the two Amercoat 235 coats (and the two ABC 3 coats) shall be applied in contrasting/alternating colors so each coat’s coverage can be visually verified. Final PSX 700 finish colors per the vessel color schedule.
1. Decks & walking surfaces: where non-skid is required, incorporate an approved aggregate in the intermediate/finish coat or use a dedicated non-skid system — specify separately.
1. Mixing ratios, induction time, pot life, thinning, and cure/launch times shall follow the current PPG/Ameron PDS for each product.
1. DFT measured per SSPC-PA 2; keep application records (ambient conditions, DFT, batch numbers) for the coating log.
7. Manufacturer References
1. PPG Dimetcote 302 H — Product Data Sheet (reinforced inorganic zinc primer).
1. PPG Amercoat 235 — Product Data Sheet, May 1, 2018 (phenalkamine epoxy).
1. PPG PSX 700 — Product Data Sheet, Nov 6, 2023 (engineered siloxane).
1. PPG ABC 3 — Product Data Sheet, May 1, 2018 (tin-free self-polishing antifouling).
This specification summarizes manufacturer data for bid/planning use. The current PPG/Ameron Product Data Sheets and Application Instructions govern all work.
File details come from the government source that posted it. Updated .