USS_O'KANE_PPI_QA3.xlsm

Sheet1

Contractor has reviewed this work item and all associated reference material noting that the PCMS material required to accomplish the requirements of paragraph 3.5 is not identified or provided.

Bidder's Questions:

Will the PCMS material required to accomplish the requirements of paragraph 3.5 be provided as GFM?

Paragraph 3.1.1 states, “Flex Hoses shall be shipped to ATTN: Code 946 3418 Brinser St. San Diego, CA 92136”.

Question 1: Is Code 946 going to repair/fabricate new hoses? If so, is Code 946 going to accomplish paragraphs 3.3.2 through 3.3.6.1?

Question 2: Does the directed Labor and Dollars in para 3.1 include cost of repair by Code 946?

Question 3: Please clarify who is tasked to accomplish the repair/fabrication of new hoses.

5.1.1 - GFM listed as “Turning Gear Overhaul Kit MA050118” does not show up in reference 2.2 or the stock system.

Please confirm that “Turning Gear Overhaul Kit MA050118” satisfies all material required to accomplish 3.6.1.

For bidding purposes is it the Government’s intent to provide 9ea (WTRTT) Doors as GFM?

KTR notes, Test Note T2 of 2.2 states, “In lieu of a Hydrostatic Test, a tightness check at system at system nominal operating pressure may be performed IAW NAVSEA S9AA-AB-GOS-010/GSO and NSTM; NAVSEA S9086-RK-STM-010/CHAPTER 505. Unless otherwise directed for estimating purposes KTR will bid to accomplish tightness check at nominal system pressure in lieu of hydrostatic testing called out in PARA 3.2

KTR notes para 3.4 is a duplicate of PARA 3.3 “(V) (G) “OPERATIONAL TEST” in accordance with Test Note T3 of 2.2. Will the government be deleting the requirements of PARA 3.4 by Amendment?

It is understood that the sheets called out in 3.1 are for ripout of electrical cable and equipment. No other paragraphs in the specification state to accomplish any installation of electrical cable or equipment. It is also not clear if AIT or government will accomplish the electrical portions of this install.

KTR requests clarification as to who is to accomplish the electrical installations of reference 2.2

Unless otherwise directed no electrical installation will be accomplished and will only be accomplished with a change order.

Please review, advise or concur.

KTR notes:

A. There are various components between the two valves listed in PARA 3.2. Is it the government’s intent to replace all components between the valves listed?

B. Reference 2.2 is a System Diagram drawing and does not provide enough detail to ascertain an accurate list of materials. For estimating purposes will the government provide a list of materials required to accomplish repairs?

C. PARA 1.2 only lists Auxiliary Machinery Room No. One (4-126-0-E) for location of repairs, however FM-V-458 is located outside of the Auxiliary Machinery Room No. One. Will the government be adding the additional location of work by ERRATA.

Contractor reasons 3.3 should not state NEW as the Sensor Operational Test for the new windows is covered on paragraph 3.15.

Please clarify intent of para 3.3.

It is also noted that no quantities are provided for stuffing tubes or jack box studs.

KTR requests clarification for quantities to be replaced.

Unless otherwise directed KTR will estimate to have one each stuffing tube and one each jack box stud replaced at each location listed in 1.2.1 through 1.2.19. Any changes in estimated quantities will be subject to change order.

Please review, advise or concur.

Para. 3.3 specifies “Dispose of the following located in 1.2, (Pier adjacent to the ship and AMR 1 4-126-0-E), when directed by the SUPERVISOR:

3.3.1 HD 1140/SPY Water Cooling piping flange to flange 65 inch seawater piping containing venturi.

3.3.2 Tubing from the venturi on the removed seawater piping

3.3.2.1 Seawater gauge, SW-GA-47

3.3.2.2 Pump out 100 gallons of seawater bilge…

Please clarify intent of para 3.3.

Note that there is neither a paragraph 4.1.1 nor 4.1.2 in the work item. Please clarify intent of paras 3.10.1 and 3.10.2

For bidding purposes, is it the Government’s intent to reinstall and test 1B Osmosis unit after structural repairs have been completed? Or is it the Government’s intent to transport equipment off ship?

Is the Government going to provide critical alignment and in-place machining services?

Is the Government going to provide critical alignment and in-place machining services?

For bidding purposes, please define if the quantified repairs in 3.3 are on the deck, bulkhead or overhead of the compartment.

Plating is identified under 1.3.4. Quantity (2 Sq Ft) Main Deck Plating, Frame 389, 11 FT 3 IN Port off Centerline, 0.375 Plate, MIL-S-22698 (PL103), Sht 3-10 of

1.3.4 Quantity (2 Sq Ft) Main Deck Plating, Frame 389, 11 FT 3 IN Port off Centerline, 0.375 Plate, MIL-S-22698 (PL103), Sht 3-10 of 2.2.

69 150-11-001 Decoy Launcher Base No. 4; Repair 150-11-001 Para 3.4 tasks KTR to accomplish the following repairs for foundation and deck identified in 1.3, using the results in report of 3.3.1. Para 3.2.1 is the report submitted based on inspection in para 3.3.

For bidding purposes, please define if the quantified repairs in 3.3 are on the deck, bulkhead or overhead of the compartment.

For bidding purposes, please define if the quantified repairs in 3.3 are on the deck, bulkhead or overhead of the compartment.

For bidding purposes, please define if the quantified repairs in 3.3 are on the deck, bulkhead or overhead of the compartment.

Is the Decoy Launcher equipment being removed by AIT?,

Reference 2.4 is not listed on the spec, unless otherwise directed contractor will use reference 2.3 as the correct reference, please concur.

For estimating purposes, please define quantity of Vermiculite Coating to be abated.

For bidding purposes what is the amount of square feet of BHD plating that will be replaced?

Ktr to conduct ship check for quantity of BHD plating. Ship check dates have been updated to 14 AUG for USS DECATUR in section L, 3.0 of the solicitation in future Amendment 0003.

&P of &N

Sheet2

Sheet3 image1.jpeg image2.png