SOW_23_Sep.pdf

FOR OFFICIAL USE ONLY

Statement of Work for

Communication, Navigation, Surveillance / Air Traffic Management (CNS/ATM) Block 45 Group A

Production Kits

Permanent Modification for the

C/KC-135

Preparation Date: 23 September 2014

Purchase Request No. TBD

PREPARING ORGANIZATION: AFLCMC/WKDM TINKER AFB OK 73145

1. Scope This Statement of Work (SOW) defines the work to be performed by the Contractor for the Government to procure, validate and verify the Communication, Navigation, Surveillance / Air Traffic Management (CNS/ATM) Block 45 Group A production kits.

The work performed by the Contractor shall consist of the development, fabrication, testing, packaging and management to deliver up to 377 Block 45 Group A production kits. This work is required to support the installation of the Block 45 modification on C/KC-135 aircraft.

1.1. Background

Block 45 Engineering and Manufacturing Development / Low Rate Initial Production (EMD/LRIP) contract was awarded to Rockwell Collins Inc. (RCI), Government Systems on 14 September 2009. The contract was a sole source award for Research & Development and LRIP phase of the CNS/ATM Block 45 ACAT III requirement. The government obtained the re-procurable unlimited technical data package from RCI for the Group A production kit through the EMD/LRIP contract. The technical data package obtained is being used to compete a source or sources to provide the Government with the Block 45 Group A production kits required to modify the remaining C/KC-135 fleet with the Block 45 modification.

2. Applicable Documents The following documents are applicable to this Statement of Work.

2.1. Department of Defense (DoD) Specifications

Unless otherwise indicated, copies of specifications, standards and handbooks listed below are available from the Standardization Document Order Desk, 700 Robbins Ave, Bldg 4D, Philadelphia PA 19111-5094.

2.2. Department of Defense Standards

MIL-HDBK-61A Configuration Management Guidance MIL-STD-129P Military Marking for Shipping and Storage MIL-STD-130N DOD Standard Practice Identification

Marking of U.S. Military Property MIL-STD-2073-1D Standard Practice for Military Packaging

2.3. Industry Publications

ASTM-D-3951 Commercial Packaging SAE AS50881 Wiring Aerospace Vehicle SAE AS-9132 Data Matrix Quality Requirements for

Parts Marking

3. Requirements

3.1. Program Management

The Contractor shall designate a single point of contact (POC) for all tasks required for the program. The POC shall have responsibility and authority for the control and coordination of all work performed under this Statement of Work.

3.2. General Requirements

The Contractor shall manufacture, fabricate, test, package and deliver all Block 45 Group A production kit components required to construct a kit IAW drawings and technical data provided in Table 5 and other supporting documents in Table 6. The Block 45 Group A production kit is required to integrate and install Block 45 Group B Line Replaceable Units (LRUs) into the C/KC-135 aircraft. The Group B LRUs are identified in Table 1 and are not a requirement of this SOW to be procured, however they are identified in the provided drawing and data package. The Block 45 Group A production kits include, but are not limited to, cables, wiring, junction boxes, connectors, lights, panels, mounts, racks and the hardware necessary to install Group B LRUs as identified in the drawings and technical data package provided. The Block 45 Group A production kit types shall comply with the requirements of this SOW.

Nomenclature Part Number

NSN

Autopilot Computer (APC-7000) 822-2614-100 6615-01-612-6778 Aural Warning Generator 270-3303-010 6340-01-612-0330

Common Computing Module, CCM-7010 822-1605-702 6610-01-607-8246 Mode Select Panel (MSP-7000) 822-2954-001 6615-01-612-5866

MFD-2912L2 822-2951-001 6610-01-611-4034

Autopilot Panel (APP-7000) 822-2612-002 6615-01-612-5266

Servo Assy SVO-5000 822-2136-101 6615-01-612-7259 Mount, Servo SMT-5003 822-2921-001 6615-01-612-6784

Radio Altimeter, Low Range (LRA-2100) 822-2365-600 5826-01-609-5635 Data Concentrator Unit 270-3285-010 6610-01-609-2803

Table 1, Block 45 Group B LRUs

3.2.1 Identification Marking Requirements

The Contractor shall mark all items as identified in provided drawings IAW MIL-STD- 130N.

3.2.1.1 Item Unique Identification (IUID) Requirements

The Block 45 program has implemented Item Unique Identification (IUID) to improve asset visibility and to more accurately capture data/intelligence about an asset throughout its lifecycle. The Contractor shall identify and mark the Group A specified items with IUID labeling IAW DFARS 211.274-5(a), Policy for Assignment of Government-assigned serial numbers and DFARS 212.301(f)(vi), Solicitation Provisions and Contract Clauses for the Acquisition of Commercial Items .

The Contractor shall provide an IUID for all items for which the Government’s unit acquisition cost is $5,000 or over, as identified in Table 2. The Contractor shall provide a IUID Marking Plan (CDRL A001) and a IUID Verification Report (CDRL A002) All IUID markings will comply IAW SAE AS-9132, Data Matrix Quality Requirements for Parts Marking as required by MIL-STD-130N, DOD Standard Practice Identification Marking of U.S. Military Property.

Nomenclature Part Number NSN Landing Gear Panel 818-3871-003 6610-01-614-6477

Terrain Light Control Panel 818-3785-002 6220-01-614-9440 Flight Director Tie Panel 818-3785-010 1680-01-614-9323

Table 2, Block 45 IUID Marked Items

3.3. Quality Processes and Procedures

The Contractor shall provide all documentation concerning quality process and procedures for manufacturing i.e. AS9100B/ISO9001:2008 certified.

3.4. Estimated Production and Delivery

The Contractor shall provide up to 377 Block 45 Group A production kits to the Government IAW Block 45 Group A Kit Delivery Schedule (below). The contractor shall provide details of how they will meet the Block 45 Group A production kit delivery schedule by providing a detailed Integrated Master Schedule (CDRL A003).

Basic contract - FY15-17 (Minimum: 5 units, BEQ: 121 units) includes first production article, 100% Physical Configuration Audit (PCA) at contractor facility

- PCA kit must be delivered No Later Than (NLT) 210 days After Receipt of Order (ARO)

- Remaining minimum award kits must be delivered NLT 90 days after approval of PCA

- Any additional kits ordered on the Basic Contract must begin delivery NLT 210 days ARO and complete deliveries NLT 365 days ARO

Option 1 - FY18 (BEQ: 33 units)

- Option 1 kits must begin delivery NLT 210 days ARO and complete deliveries

NLT 365 days ARO Option 2 - FY19 (BEQ: 32 units)

- Option 2 kits must begin delivery NLT 210 days ARO and complete deliveries NLT 365 days ARO Option 3 - FY20 (BEQ: 45 units)

- Option 3 kits must begin delivery NLT 210 days ARO and complete deliveries NLT 365 days ARO Option 4 - FY21 (BEQ: 45 units)

- Option 4 kits must begin delivery NLT 210 days ARO and complete deliveries NLT 365 days ARO Option 5 - FY22 (BEQ: 45 units)

- Option 5 kits must begin delivery NLT 210 days ARO and complete deliveries NLT 365 days ARO

Option 6 - FY23 (BEQ: 56 units)

- Option 6 kits must begin delivery NLT 210 days ARO and complete deliveries

NLT 365 days ARO

A total buy to modify 377 C/KC-135 production aircraft is expected from FY15-23. The acquisition of production kits extends into FY23. The purchase quantity per FY for the USAF is subject to change based on funding authorizations. Due to budget constraints quantities may push out to additional Fiscal Years. Estimated calculations allow for yearly escalation.

3.4.1. Physical Configuration Audit (PCA)

The Government will conduct, with Contractor participation, a 100% configuration audit on the first Block 45 Group A production kit to verify the actual configuration meets the provided drawing and technical data package specifications. The Contractor will provide a Configuration Audit Plan (CDRL A004), when it notifies the government it is ready for the PCA. The PCA will be held at the Contractor’s facility and will be operated IAW MIL-HDBK-61A. The Contractor shall ensure that the PCA audits result in:

• Configuration is equal and built to the government provided drawings and technical data, in Table 5 and Table 6, as final configuration requirement

• Wiring, cables, and cable bundles pass continuity checks IAW SAE AS50881

The Government will provide approval to continue delivery of the basic order after government approved Physical Configuration Audit.

3.4.2. Package and Handling

The Contractor shall package the Block 45 Group A production kits for shipment in accordance with ASTM-D-3951, Commercial Packaging or MIL-STD-2073-1D, the Standard Practice for Military Packaging. The Contractor shall mark the packages for shipping and storage in accordance with MIL-STD-129P, Military Marking for Shipment and Storage, and ship them to the following address:

FB2039 OC-ALC

Bldg. 506 CML PH (405) 739-2349 7401 Arnold St. Door 22 Tinker AFB, OK 73145-9013 Mark for: Account 09 (1560K0109315AFL)

The Government may amend shipping instructions.

3.5. Warranty

The Contractor shall provide a one-year (12 Month) warranty IAW FAR Part 52.246-17 Warranty of Supplies of a Noncomplex Nature.

4. Government Furnished Information The Government will provide the drawings and technical data package in Table 5 required to manufacture the Block 45 Group A installation production Kit.

Drawing Number Title 818-3773-001 KC-135 Block 45 Top Level 818-3774-001 Drawing Structure 818-3775-001 Removal list 818-3776-001 Post Installation Checkout 818-3777-001 Pre-Power/Grounds Checkout 818-3778-001 Wiring Diagram 818-3779-001 Electrical Installation 818-3779-002 Electrical Wiring Modification 818-3801-001 Wire Fabrication 818-3779-003 Harness Assy W2099 818-3779-004 Bracket 818-3783-005 Yoke Harness Installation Instructions 818-3800-001 Harness Assy W2068 (Coax) 818-3800-002 Harness Assy W2069 (Coax) 818-3800-003 Harness Assy W2070 (Coax) 818-3800-004 Harness Assy W2071 (Coax) 818-3800-005 Harness Assy W2072 818-3800-006 Harness Assy W2073 818-3800-007 Harness Assy W2074 818-3800-008 Harness Assy W2075 818-3800-009 Harness Assy W2076 818-3779-005 Cable, Exhaust Gas Temperature 818-3800-010 Harness Assy W2077 818-3800-011 Harness Assy W2078 818-3800-012 Harness Assy W2079 818-3800-013 Harness Assy W2080 818-3800-014 Harness Assy W2081 818-3800-015 Harness Assy W2082 818-3800-016 Harness Assy W2083 818-3800-017 Harness Assy W2084 818-3800-018 Harness Assy W2085 818-3800-019 Harness Assy W2086 818-3800-020 Harness Assy W2087 818-3800-021 Harness Assy W2088 818-3800-022 Harness Assy W2089 818-3800-023 Harness Assy W2090 818-3800-024 Harness Assy W2091 818-3800-025 Harness Assy W2092

818-3800-026 Harness Assy W2093 818-3800-027 Harness Assy W2094 818-3800-028 Harness Assy W2095 818-3800-029 Harness Assy W2100 818-3800-030 Harness Assy W2101 818-3800-031 Harness Assy W6344 818-3800-032 Harness Assy W6345 818-3800-033 Harness Assy W6348 818-3800-035 Harness Assy W2102 818-3800-036 Harness Assy W2103 818-3800-037 Harness Assy W2104 818-3800-038 Harness Assy W2105 818-3800-039 Harness Assy W2117 818-3800-040 Harness Assy W2118 818-3800-041 Harness Assy W2119 818-3800-042 Harness Assy W2120 818-3800-043 Harness Assy W2123 818-3780-001 Electronics Cabinet Modification 818-3792-001 Vertical Reference System - Modified 535-1942-01 Plate, ID 818-3805-062 Decal FDR Software 818-3780-002 Support 818-3780-003 Support 818-3780-004 Bracket 818-3780-005 Power Control Relay Assembly 818-3780-006 Plate, Cover 818-3805-001 Decal – Identification 818-3780-007 Production Test Requirements 818-3780-009 Bracket – Terminal Board 818-3780-010 Bracket, Splitters 816-3340-054 Decal – (1 – 20) 818-3805-020 Decal – RR7169 818-3805-021 Decal – RR7170 818-3805-022 Decal – RR7171 818-3805-023 Decal – RR7172 822-2614-100 Autopilot Computer (APC-7000) – GROUP B 822-2645-002 Mounting Tray Assy (MT-7000) 818-3805-024 Decal – RM8078 818-3805-025 Decal – RM8525 818-3805-026 Decal – RM8526 818-3805-027 Decal – RM8523 818-3805-028 Decal – RT7068 816-3340-017 Decal – RM8122 816-3340-026 Decal – RM8121 816-3340-104 Decal – RM8272

818-3805-048 Decal – RR7173 818-3805-049 Decal – RR7174 818-3805-050 Decal – RT7069 818-3805-053 Decal – RM8347 270-3303-010 Aural Warning Indicator Assy – GROUP B 822-1605-702 Common Computing Module, CCM-7010 –

GROUP B

818-3780-008 Discrete Relay Junction Box Modification 818-3805-054 Decal – IDENTIFICATION 214-1023-020 Relay Electromagnetic 818-3781-001 Flight Deck Modification 818-3805-017 Decal – PLT MSP 818-3805-018 Decal – CPLT MSP 818-3805-014 Decal – EEID 822-2954-001 Mode Select Panel (MSP-7000) – GROUP B

822-2951-001 MFD-2912L2 – GROUP B

818-3781-003 Screw, Cap, Socket Head 818-3871-003 Landing Gear Position Indicator (See breakout) 818-3781-004 Panel, Blank – Warning Monitor 818-3781-005 Plate, Cover – VSI 818-3805-004 Decal – LG MAX KNOTS 818-3805-005 Decal – Flaps MAX KNOTS 216-1019-780 Indicator Cap Module (AP A/R / Blank) 216-1019-770 Indicator Cap Module (HDG Miscomp) 818-3781-002 Panel Assembly, Center 818-3781-006 Artwork Screen – Cabin Pressure Emergency

Release 818-3781-007 Artwork Screen – Background 818-3781-009 Bushing 818-3782-001 Circuit Breaker Panels Modification 818-3805-029 Decal – LAMP TEST 818-3805-030 Decal – EEID/MAIN/HEATER 818-3805-031 Decal – DCU CH A 818-3805-032 Decal – DCU CH C 818-3805-033 Decal – P100 818-3805-035 Decal – APC 1 818-3805-036 Decal – APC 2 818-3805-037 Decal – APC CONT 818-3805-038 Decal – RA/AOA Cont 818-3805-039 Decal – FD CONT 1 818-3805-040 Decal – P19 818-3805-041 Decal – RAD ALT 1 818-3805-042 Decal – AOA CASE HEAT 818-3805-043 Decal – AURAL WARN

818-3805-044 Decal – DCU CH B 818-3805-045 Decal – MFDIC 818-3805-046 Decal – RAD ALT 2

308-0312-020 BUTTON, PLUG PLASTIC

426-0292-100 BUSS CABLE (15 POSITION)

426-0292-110 BUSS CABLE (18 POSITION)

818-3783-001 Yoke Modification 818-3783-002 Mount, Pushbutton Switch 818-3783-003 Mount, Slide Switch (Pilot) 818-3783-004 Mount, Slide Switch (Copilot) 266-6095-030 Switch, Pushbutton 266-0544-020 Switch, Slide 818-3784-001 Center Pedestal Modification 818-3784-002 MFDIC Display Adapter 818-3784-005 Platform, Connector Mounting 818-3784-003 Adapter, MFDIC Display 818-3784-004 Artwork Screen – MFDIC Display Adapter 818-3784-015 Production Test Requirements MFDIC

Display Adapter 818-3784-010 Support, Autopilot Flight Controller 818-3784-011 Support, Top 818-3784-012 Support, Base 818-3784-013 Support, Side 822-2612-002 Autopilot Panel (APP-7000) – GROUP B 818-3784-006 Platform, Mounting Autopilot Flight

Controller 818-3784-014 Cover, Access 846-0009-010 Fastener Retractable Screw 818-3805-019 Decal – AP CTRL 818-3784-007 Plate, Cover 818-3785-001 Overhead Panel Modification 818-3700-002 Panel, Blank – 0.750 818-3700-005 Panel, Blank – 1.875 818-3700-007 Panel, Blank – 2.625 818-3785-002 Terrain Light Control 818-3785-003 Panel Assy, Illuminated – Terrain Light

Control 818-3785-004 Panel Assy – Terrain Light Control 818-3785-005 Platform – Connector Mounting 818-3785-006 Cover, Rear 818-3785-007 Gasket 818-3805-057 Plate, Identification 818-3785-010 Speed Dev/FD TIE Control 818-3785-011 Panel Assy, Illuminated – Speed Dev/FD TIE

Control

818-3785-012 Panel Assy – Speed Dev/FD TIE Control 818-3785-013 Platform – Connector Mounting 818-3785-014 Cover, Rear 818-3785-015 Gasket

818-3805-058 PLATE, IDENTIFICATION

818-3785-020 Autopilot Refuel Mode Control 818-3785-021 Panel Assy, Illuminated – Autopilot Refuel

Mode Control 818-3785-022 Panel Assy – Autopilot Refuel Mode Control 818-3785-023 Platform – Connector Mounting 818-3785-014 Cover, Rear 818-3785-015 Gasket

818-3805-061 PLATE, IDENTIFICATION

818-3805-015 Decal – PLT WXR CTRL 818-3805-016 Decal – CPLT WXR CTRL 818-3805-051 Decal – SPEED DEV / FD TIE 818-3805-052 Decal – TERRAIN LT 818-3786-001 Forward Auxiliary Rack Installation 818-3786-002 Rack, Equipment 818-3786-003 Side, Left 818-3786-004 Side, Right 818-3786-005 Support, Vertical 818-3786-006 Tube, Vertical Support 818-3786-007 Channel, Nut 818-3786-008 Channel, Nut 818-3786-009 Support, Brace 818-3786-010 Support, Diagonal 818-3786-011 Support, Shelf 818-3786-012 Cover, Lower 818-3786-013 Cover, Upper 818-3786-020 Support, Diagonal 818-3786-014 Tray, Equipment 818-3786-015 Plate, Hold Down 818-3786-016 Shelf 818-3786-017 Bracket 818-3786-018 Bracket 818-3786-019 Cover 818-3786-021 Bracket, Load Transfer 818-3805-006 Decal – RM8105 818-3805-007 Decal – RM8106 818-3805-008 Decal – RM6821 818-3805-009 Decal – RM6822 818-3805-056 Placard – Forward Auxiliary Rack 818-3787-001 Aileron Servo Installation 822-2136-101 Servo Assy SVO-5000 – GROUP B

822-2921-001 Mount, Servo SMT-5003 – GROUP B 818-3805-010 Decal – AILERON SERVO 818-3788-001 Elevator Servo Installation 822-2136-101 Servo Assy SVO-5000 – GROUP B 822-2921-001 Mount, Servo SMT-5003 – GROUP B 818-3805-011 Decal – Elevator Servo 818-3789-001 Radio Altimeter Installation 818-3789-002 Plate, Adapter 818-3789-003 Antenna Shielding Cover Assembly 818-3789-004 Antenna Shielding Cover 818-3789-005 Isolator 818-3789-006 Retainer 822-2365-600 Radio Altimeter, Low Range (LRA-2100) -

GROUP B

866-5007-080 Tray, Equipment (ARINC 600, 3 MCU) 818-3805-012 Decal – RAD ALT NO 1 818-3805-013 Decal – RAD ALT NO 2 818-3790-001 DCU Installation 270-3285-010 Data Concentrator Unit – GROUP B 866-5007-120 Tray, Equipment (ARINC 600, 4 MCU) 818-3790-002 Plate, WXR Mounting 818-3790-003 Support 818-3790-004 Plate, DCU Mounting 818-3790-005 Cover, DCU 818-3790-006 Block, Mounting 818-3790-007 Bracket, Cable Support 818-3805-002 Decal – EEID DCU 818-3805-055 Decal – RT7070 818-3791-001 Navigator’s Station Modification 818-3791-002 Panel Assy EEID Video Interface 818-3791-003 Panel, EEID Video Interface 818-3791-004 Artwork Screen – EEID Video Interface 818-3785-013 Platform, Mounting Connector 818-3785-014 Cover, Rear 818-3785-015 Gasket 818-3805-059 Plate, Identification 818-3784-007 Plate, Cover 818-3810-001 Weight and Balance Data 818-3811-001 Structural Analysis 818-3812-001 Electrical Load Analysis 818-3813-001 Thermal Analysis 818-3814-001 Corrosion Prevention and Control Plan

Table 5, Drawing List

The Government will provide the miscellaneous documents and technical data in Table 6 required to manufacture the Block 45 Group A production Kit.

PROCESS SPECS

219-0028 Cable Assembly Instructions 580-0036 Process Chemical Film 580-0096 Process Screen Printing 580-0799 Requirements Shelf Life in Engineering Drawings 580-1497 Process Marking Identification 580-5168 Process and Quality Requirement Application of Self-

Adhesive Identification Strip 580-5341 Requirements Process and Quality Adhesive Bonding 580-5677 Process and Quality Requirements Thread-Locking 580-5800 Fabrication Practices 820-5052 Raw Material Metallic Aluminum Alloy 5052 820-6061 Raw Material Aluminum Alloy 6061 839-5402 Fabrication Assembly Practices 839-7004 Instructions Connector Assembly 839-7015 Instructions Connector Assembly AS50881 Rev C Wiring Aerospace Vehicle CTS122 Installation Instructions for Straight Plug for ECS

Cable L1122 Installation Instructions for ARINC 600 RF Connector

RC-ENG-I-001 Product Definition Instructions (PDI) RC-WSM1-22 Workmanship Standards

MISC MATERIAL

0000-10000 Backshell Assembly Method 005-1540 Adhesive 005-2028 Thread Locking Compound 005-2892 Solvent Alcohol-Blend 012-0039 Panel Fastener Stud Assembly 014-0842 Tape Silicon 015-4609 Accessories Connector 139-0976 Loop Clamp 152-0076 Labels Flat 152-0083 Sleeving Expandable 152-2399 Electrical Insulation Sleeving 152-2563 Insulation Sleeving Electrical 152-3373 Cable Spiral Wrap 152-5183 Sealing Splice 206-0102 Connector Dust Cap Circular 206-0125 Adapter Electrical Connector 208-0104 Solder Sleeve

208-1012 Marker Cable 208-1013 Marker Cable 208-1052 Label 214-1023 Relay Electromagnetic 216-1019 Indicator, Push-Button Switch 238-1004 Potentiometer 244-1032 Fastner Retractable Screw Phillips 246-1180 Knob 263-1074 Contact Connector 263-1102 Connector Electrical Plug 263-1109 Connector Protective Cover 266-0543 Switch Toggle 266-0544 Switch Slide 266-5321 Toggle Switch 266-6095 Switch Push Button 304-1089 Terminal Lug-Bent 305-1375 Rivet 308-0312 Button Plug Plastic 338-2010 J Pins 357-7204 Connector Plug Electrical 358-0044 Connector Contact 359-0332 Connector Circular Plug Quadrax 359-0341 Connector Circular Cable Plug 359-0406 Adapter Connector Electrical 359-0608 Contact Electrical Connector 359-0625 Plug Sealing Electrical Connector 359-0692 Coaxial Contacts 359-0717 Seal Contact 370-0066 Arinc-600 Size 2 Connector Plug Electric 370-0138 Connector Backshell Arinc 600 371-0637 Connector Receptacle 424-0966 Cable Ethernet 425-0279 Cable Radio Frequency Quadrax 426-0292 Cable Assembly Bus 435-1019 Tape Coated Cloth 580-9016 Cable Assembly 820-2499 Raw Material Metallic Aluminum Alloy 2024

822-2645-002 Mounting Base Electrical Equipment MT-7000 839-7004 Instructions Connector Assembly 839-7015 Instructions Connector Assembly 846-0009 Panel Fastener 857-1502 RF Plug Connector 858-5804 Cable Radio Frequency 866-5007 ARINC Equipment Tray 382410A LVDS Data Bus Cable

MECHANICAL

541-6507-002 Rev-N (Pin, Straight – Headed) 816-3337-001 Rev-D (Bracket, Relay) 818-3700-006 Rev-A (Panel, Blank) 818-3790-010 Rev-A (Functional Requirements for DCU 983-4318-003 Rev-A (Pin Guide) 983-8343-120 Rev- (Tray, Mount – Riveted) 983-8343-121 Rev- (Tray, Mount) 983-8343-122 Rev- (Mount, Front)

985-0249 (Plate, Identification)

LANDING GEAR POSITION

100-160063B Resistor, Chip, Thick Film 100-230478 Rev-E Connector Assembly 100-230480 P-1 Connector assembly 100-230481 P-1 Connector 100-230498 1.25mm Crimping Connector 100-280005 Rev-B (Tape, Double Back)

100-28022NC Compound, Thread Locking 100-300000 Rev-E (Solder)

100-300020A Aluminum, Rectangle, .375 Thk 100-310007NC Film, Vinyl, White, Destructible

100-310112 Rev-A (Gasket) 100-360094 Rev-B (NVIS Green Filter) 100-360095 Rev-B (NVIS Red Filter) 100-400058 Rev-A (Acrylic Sheet 2064 Gray)

100-400145NC Label, ESD Warning 100-880007 Redline Rev-C (Resistor, Chip, Thick Film)

100-940043NC Wire, Electrical 100-990005 Rev-B (Capacitor, Chip Ceramic) 100-990073 Rev-NC (Capacitor SM 0402, 16V) 340-000344 Rev-C (Front Panel) 340-000347 Rev-B (Back Plate) 340-000364 Rev-A (Led Partition) 340-000365 Rev-C (Diffuser M/F Valox FR-1) 340-000367 Rev-A (Space, Clear M/F Hostaphan Polyester Film) 340-000368 Rev-A (Annunciator Legend) 340-000369 Rev-A (Spacer, Aluminum)

400-001002A Paint, Epoxy, Flat White 400-001024 Rev-A (Paint, Ink, white) 400-001117 Rev-J (Paint, Urethane, Black) 400-001122 Rev-NC (Paint, Ink, Black)

400-001800A Conformal Coating, Clear 400-001805 Rev-F (Paint, UV Blocking, Flat Clear)

400-001830 Rev-J (Paint, Urethane, UV Resistant, NVIS

Compliant) 465-000024 Rev-A (Film, Plastic – Clear Polyester) 540-000235 Rev-D (Electronic Component Assembly) 540-000255 Rev-B (Front Panel Assembly) 605-000320 Rev-A (Gerber File Data Set Approval) 665-000320 Rev-A (PWB) 675-000235 Rev-E (Schematic, KC-135 Landing Gear Indicator) 840-000178 Rev-D (Landing Gear Position Indicator Panel)

840-000178-AD Rev-D (Landing Gear Position Indicator Top Level Assy)

DECALS

816-3340 Rev-F (Decals)

EXCEL SPREADSHEETS

Block 45 Group A Decals, Electrical, Mechanical, Procedures Removal List, Top Level 10813 Block 45 Group A Misc Material Block 45 Group A Process Specs Changes Block 45 Group A Misc Material

540-000235 Landing Gear Panel Parts List

PL840-000178-

AD

Landing Gear Panel Item Descriptions

Block 45 818-3773-001 Indentured BOM Rev-A KC-135 Block 45 CPN-VPN Cross Reference

Table 6, Miscellaneous Documents / Technical Data List

5. CDRL List

CDRL Item # Title Frequency

CDRL A001 Item Unique Identification Marking Plan As Required IAW CDRL Remarks

CDRL A004 Item Unique Identification Verification Report As Required IAW CDRL Remarks

CDRL A003 Data Accession List Monthly CDRL A004 Configuration Audit Plan As Required IAW CDRL Remarks