Attachment_4__-_Environmental_Protection_Guide.pdf

ENVIRONMENTAL PROTECTION

SPECIFICATIONS AND GUIDANCE

FOR

MARCH ARB

BASED ON THE UNIFIED FACILITY GUIDE SPECIFICATION

DIVISION 01 – GENERAL REQUIREMENTS, SECTION 01 57 19

TEMPORARY ENVIRONMENTAL CONTROLS

Prepared by 452 Mission Support Group Base Civil Engineer Squadron (BOS)

Environmental Flight (CEV)

JUNE 2019

Attachment 4

FA466419BA008

Table of Contents

PART 1 GENERAL

1.1 REFERENCES

1.2 DEFINITIONS

1.2.1 Class I and II Ozone Depleting Substance (ODS)

1.2.2 Contractor Generated Hazardous Waste

1.2.3 Electronics Waste

1.2.4 Environmental Pollution and Damage

1.2.5 Environmental Protection

1.2.6 Hazardous Debris

1.2.7 Hazardous Materials

1.2.8 Hazardous Waste

1.2.9 Land Application

1.2.10 Municipal Separate Storm Sewer System (MS4) Permit

1.2.11 National Pollutant Discharge Elimination System (NPDES)

1.2.12 Oily Waste

1.2.13 Regulated Waste

1.2.14 Sediment

1.2.15 Solid Waste

1.2.16 Debris

1.2.17 Green Waste

1.2.18 Material not regulated as solid waste

1.2.19 Non-Hazardous Waste

1.2.20 Recyclables

1.2.21 Surplus Soil

1.2.22 Scrap Metal

1.2.23 SURFACE DISCHARGE

1.2.24 STORMWATER

1.2.25 Wood

1.2.26 Wastewater

1.2.27 Waters of the United States

1.2.28 Wetlands

1.2.29 Universal Waste

1.3 SUBMITTALS

1.3.1 SD-01 Pre-contract Submittals – all preconstruction/pre-contract start work submittals shall be submitted as part of the environmental protection plan (EPP) 10 days prior to the start of any activities on March ARB as discussed below:

1.4 SD-11 Closeout Submittals

1.4.1 Stormwater Pollution Prevention Plan Compliance Notebook as required by State Water Board; G, CEV

1.4.2 Stormwater Notice of Termination (for NPDES coverage under the general permit for construction activities); G, CEV

1.4.3 Environmental Records Binder to include, if applicable to work required: G, CEV

1.4.4 Aboveground Storage Tank - technical information G, CEV

1.4.5 A Recovered Materials Determination Form (RMDF) (paragraph B). G, CEV

1.4.6 An Estimate of Percentage of Recovered Material Content for EPA-Designated Products (paragraph D G, CEV

1.4.7 Meter Logs for Generators and certification of meter reading at turn over/Commissioning . 17

1.4.8 HVAC Maintenance Manual; G, CEV/CECC

1.4.9 Refrigerant Log; G, CEV

1.5 ENVIRONMENTAL PROTECTION REQUIREMENTS

1.6 Conformance with the Environmental Management System

1.7 SPECIAL ENVIRONMENTAL REQUIREMENTS

1.7.1 Environmental Coordination:

1.7.2 Environmental Planning:

1.7.3 Environmental Audits/Inspections:

1.7.4 Notices of Violations (NOV):

1.8 QUALITY ASSURANCE

1.8.1 Pre-contract Start Survey and Protection of Features

1.8.2 Regulatory Notifications

1.8.3 Environmental Brief/Pre-Installation Conference

1.8.4 Environmental Manager

1.8.5 Employee Training Records

1.8.6 Non-Compliance Notifications

1.9 ENVIRONMENTAL PROTECTION PLAN (EPP) REQUIREMENTS

1.9.1 General:

1.9.2 General Site Information

1.9.3 Management of Natural Resources

1.9.4 Protection of Historical and Archaeological Resources

1.9.5 Stormwater Management and Control

1.9.6 Protection of the Environment from Waste Derived from Contractor

1.9.7 Regulatory Notification and Permits

1.9.8 Clean Air Act Compliance

1.10 LICENSES AND PERMITS

1.11 SOLID WASTE MANAGEMENT PERMIT

1.11.1 Solid Waste Management Report

1.12 FACILITY HAZARDOUS WASTE GENERATOR STATUS

1.13 ENVIRONMENTAL RECORDS BINDER

2 PRODUCTS

3 EXECUTION

3.1 PROTECTION OF NATURAL RESOURCES

3.1.21 Flow Ways

3.1.22 Vegetation

3.2 STORM WATER

3.2.1 General:

3.2.2 Storm Water Best Management Practices (BMPs):

3.2.3 Dumping In Storm Water System

3.2.4 Construction General Permit

3.2.5 Stormwater Pollution Prevention Plan (SWPPP):

3.2.6 Erosion and Sediment Control Measures

3.2.7 Work Area Limits

3.2.8 Contractor Facilities and Work

3.2.9 Municipal Separate Storm Sewer System (MS4) Management

3.3 SURFACE AND GROUNDWATER

3.3.1 Waters of the United States

3.4 PRESERVATION OF ARCHEOLOGICAL AND HISTORICAL SITES

3.4.1 Historic District

3.5 AIR RESOURCES

3.5.1 General:

3.5.2 Burning

3.5.3 Ozone Depleting Substance (ODS):

3.5.4 Accidental Venting of Refrigerant

3.5.5 EPA Certification Requirements

3.5.6 Dust and particulate matter emissions

3.5.7 Odors

3.5.8 Violations:

3.6 SOLID WASTE REQUIREMENTS (Includes, Construction, Demolition, and Deconstruction) 32

3.6.1 General:

3.6.2 WASTE MINIMIZATION

3.6.3 Salvage, Reuse and Recycle

3.6.4 Nonhazardous Solid Waste Diversion Report

3.7 WASTE MANAGEMENT AND DISPOSAL

3.7.1 Waste Determination Documentation

3.7.2 Solid Waste Management

3.7.3 Control and Management of Hazardous Waste

3.7.4 March ARB Hazardous Waste Management Plan (HWMP):

3.7.5 Hazardous Waste Disposal

3.7.6 Universal Waste Management

3.7.7 Electronics End-of-Life Management

3.7.8 Disposal Documentation for Hazardous and Regulated Waste

3.8 Wastewater

3.8.1 Disposal of wastewater must be as specified below

3.8.2 Domestic Wastewater:

3.8.3 Industrial Wastewater:

3.9 HAZARDOUS MATERIAL MANAGEMENT

3.9.1 General:

3.9.2 Short Term Construction and Service Contracts Hazardous Material Reporting Requirements:

3.9.3 Long Term Service Contract:

3.10 Pesticide Management:

3.10.1 Pesticide Approval

3.10.2 License and Certificates

3.10.3 Monthly Reporting of Pesticide Use

3.10.4 Restricted Uses

3.10.5 Preferred Substitutions:

3.11 PREVIOUSLY USED EQUIPMENT

3.12 CONTROL AND MANAGEMENT OF ASBESTOS-CONTAINING MATERIAL (ACM)

3.13 CONTROL AND MANAGEMENT OF LEAD-BASED PAINT (LBP)

3.14 CONTROL AND MANAGEMENT OF POLYCHLORINATED BIPHENYLS (PCBS)

3.14.1 General:

3.15 CONTROL AND MANAGEMENT OF LIGHTING BALLAST AND LAMPS CONTAINING

PCBS

3.16 PETROLEUM, OIL, LUBRICANT (POL) STORAGE AND FUELING

3.16.1 Used Oil Management

3.16.2 Oil Storage Including Fuel Tanks

3.16.3 ABOVE GROUND STORAGE TANKS (AST) REQUIREMENTS

3.16.4 INADVERTENT DISCOVERY OF PETROLEUM-CONTAMINATED SOIL OR

HAZARDOUS WASTES

3.17 Mercury Materials

3.18 Pesticides

3.19 WATER QUALITY REQUIREMENTS

3.19.1 Ambient Water:

3.19.2 SPILL OR RELEASE AND CLEANUP REQUIREMENTS

3.19.3 ENVIRONMENTAL TRAINING REQUIREMENTS

3.19.4 GREEN PROCUREMENT PROGRAM (GPP) REQUIREMENTS

3.19.5 ENERGY USAGE REQUIREMENTS

3.19.6 NOISE

3.19.7 DEMOLITION

4 ATTACHMENT 1. ENVIRONMENTAL PROTECTION PLAN

PART 1 GENERAL

1.1 REFERENCES

The laws, regulations and guidance provided in the publications listed below form a part of this specification to the extent applicable by the work required within the specifications. The publications listed below are identified by the basic designation only within the text of this specification. The order of preference for compliance with the listed References are as listed below, however, where contradictions or overlap may exist preference is Federal, State, local laws and regulations, Department of Defense, Air Force instruction and manuals, March ARB manuals and guidance, State guidance and other guidance. When a lower guidance contains more strict requirements, the lower guidance shall be followed. The latest update or revision of the listed references should be used.

UNITED STATES FEDERAL LAWS

16 U.S.C. 703-712 Migratory Bird Treaty Act 16 U.S.C. 470 et seq. Act of 1966 National Historic Preservation Act Compensation and Liability Act (CERCLA) Comprehensive Environmental Response, Resource Conservation and Recovery Act (RCRA), Section 6002 Government’s Green Procurement Act Public Law 93-205, 35 U.S.C. §1531 Endangered Species Act Public Law 109-58 Energy Policy Act

Public Law 91-190 National Environmental Policy Act Public Law 101-601 and Repatriation Act of 1990 Native American Graves Protection Public Law 95-341 Act of 1978 American Indian Religious Freedom Environmental Protection Agency Toxic Substances Control Act (TSCA)

UNITED STATES CODE OF REGULATIONS (CFR) PUBLICATIONS

15 USC 2651 Public Law 99-519, Response Act of 1986 (AHERA) Asbestos Hazard Emergency 16 U.S.C. 470 aa-mm Protection Act of 1979 Archaeological Resources

29 CFR 1910.13

Respiratory Protection

29 CFR 1910.14

Sanitation

29 CFR 1910.14

The Control of Hazardous Energy (Lock Out/Tag Out)

29 CFR 1910.12 Hazardous Waste Operations and Emergency Response 29 CFR 1926.11 Asbestos

29 CFR 1926.32 Definition

29 CFR 1926 Safety And Health Regulations for Construction 32 CFR. 989 Environmental Impact Analysis Process 33 CFR 328 Definitions of Waters of the United States 33 U.S.C.

§1251 et seq.

Clean Water Act of 1972

40 CFR. 50-99 Air Programs 40 CFR 61 Protection of the Environment

40 CFR 61

Subpart National Emission Standards for Asbestos

M, 40 CFR 68 Chemical Accident Prevention Provisions 40 CFR 82 Protection of Stratospheric Ozone 40 CFR 98 Mandatory Reporting of Greenhouse Gas 40 CFR 112 Oil Pollution Prevention 40 CFR 122.26 Storm Water Discharges (Applicable to State NPDES Programs, see section

123.25)

40 CFR 152 -

Pesticide Programs

40 CFR 241 Guidelines for Disposal of Solid Waste 40 CFR 243 Guidelines for the Storage and Collection of residential, commercial, and Institutional Solid Waste

40 CFR 257 Criteria for Classification of Solid Waste Disposal 40 CFR 258 Subtitle D Landfill Requirements 40 CFR 260 Hazardous Waste Management Systems: General

40 CFR 260-

Hazardous Waste Regulations

40 CFR 261 Identification & Listing of Hazardous Waste 40 CFR 262 Standards Applicable to Generators of Hazardous Waste 40 CFR 263 Standards Applicable to Transporters of Hazardous Waste 40 CFR 264 Standards for Owners and Operators of Hazardous Waste Treatment, Storage &

Disposal Facilities 40 CFR 279 Standards for the Management of Used Oil 40 CFR 280 Technical Standards and Corrective Action Requirements for Owners and

Operators of Underground Storage Tanks (UST) 40 CFR 300 National Oil and Hazardous Substances Pollution Contingency Plan 40 CFR 302 Designation, Reportable Quantities, and Notification 40 CFR 355 Emergency Planning and Notification

40 CFR 372-

Subpart D

Specific Toxic Chemical Listings

40 CFR 761 PCB Manufacturing, Processing, Distribution in Commerce, and Use Prohibitions 40 CFR 763 Asbestos-Containing Materials in Schools

40 CFR. 1500-

Council on Environmental Quality

42 CFR 84 Approval of Respiratory Protective Devices 49 CFR 107 Hazardous Materials Program Procedures 49 CFR 171 General Information, Regulations, and Definitions

49 CFR 171 -

Hazardous Materials Regulations

49 CFR 172 Hazardous Materials Table, Special Provisions, Hazardous Materials Communications, Emergency Response Information, and Training Requirements

49 CFR 173 Shippers - General Requirements for Shipments and Packaging

EXECUTIVE ORDERS

White House Memorandum, Environmentally and Economically Beneficial Practices on Federal Landscaped Grounds

DEPARTMENT OF DEFENSE INSTRUCTION AND MEMORANDUMS

AIR FORCE INSTRUTIONS AND PAMPHLETS

E.O.

11990

Protection of Wetlands

E.O.

12088, Federal Compliance and Pollution Control Standards, 13 Oct 78

E.O.

12114, Environmental Effects Abroad of Major Federal Actions, 4 Jan 79

E.O.

13112

Invasive Species

E.O.

13150

Federal Workforce Transportation

E.O.

13186

Responsibilities of Federal Agencies to Protect Migratory Birds

E.O.

13211

Actions Concerning Regulations That Significantly Affect Energy Supply, Distribution or Use

E.O.

13221

Energy Efficient Standby Power Devices

E.O.

13423, Strengthening Federal Environmental, Energy, and Transportation Management, 24 Jan 07

E.O.

13514

Federal Leadership in Environmental, Energy and Economic Performance

E.O.

13514, Federal Leadership in Environmental, Energy, and Economic Performance, 8 Oct 09

E.O.

13693, Planning for Federal Sustainability in the Next Decade, 19 Mar 15

DOD 4500.9-R,

Defense Transportation Regulation (DTR)—Part II: Cargo Movement, Chapter 204, Hazardous Materials, 24 Nov 14

DoDD 4715.1E, Environment, Safety, and Occupational Health (ESOH), 19 Mar 05 DoDD 5000.01, The Defense Acquisition System, 12 May 03

DODI 4710.02,

DoD Interactions with Federally Recognized Tribes, 14 Sep 06 DoDI 4715.06, Environmental Compliance in the United States, 4 May 15

DoDI 4715.08, Remediation of Environmental Contamination Outside the United States, 1 Nov 13

DoDI 4715.17, Environmental Management System, 15 Apr 09 DoDI 5000.02, Operation of the Defense Acquisition System, 7 Jan 15

DoDI 6050.05, DOD Hazard Communication (HAZCOM) Program, 15 Aug 06 DoDM 4140.1, DOD Supply Chain Materiel Management Procedures, 10 Feb 14

AFI 10-2501,

Air Force Emergency Management Program Planning and Operations, 24 Jan 07

AFOSHSTD 48-20, Occupational Noise and Hearing Conservation Program, 10 May 13 AFPAM 32-7043, Hazardous Waste Management Guide, 1 Nov 95 Engineering Technical Letter (ETL) 03-1 Storm water construction standards, HQ AFCESA/CESC dated 24 March 2003

CALIFORNIA CODE OF REGULATIONS (CCR) PUBLICATIONS

Title 8 CCR 1529 Asbestos in Construction Title 8 CCR 5203 Registration and Training Title 8 CCR 5208 Asbestos in General Industry Title 8 CCR 341.15 Certification of Asbestos Consultants and Site Surveillance Title 17 CCR 93106 Airborne Toxic Control Measures – Surfacing Applications Title 17 CCR 93105 Airborne Toxic Control Measures – Construction/Quarrying Title 14 CCR, Division 7, Chapter 3.5 Standards for Handling and Disposal of Asbestos Containing Waste Title 22 Div. 4.5 Environmental Health Standards for the Management of Hazardous Waste Health and Safety Code, Section 39666

NATIONAL FIRE PROTECTION ASSOCIATION (NFPA)

AFI 23-201,

Fuels Management, 20 Jun 14

AFI 23-204,

Organizational Fuel Tanks, 24 Jul 12

AFI 23-502,

Recoverable Fuel, 31 Oct 14

AFI 32-1001,

Operations Management, 16 Oct 14

AFI 32-1052,

Facility Asbestos Management, 24 Dec 14

AFI 32-1053,

Integrated Pest Management Program, 20 Nov 14

AFI 32-1067,

Water Systems and Fuel Systems, 4 Feb 15

AFI 32-7001,

Environmental Management, 16 APRIL 2015

AFI 32-7020,

The Environmental Restoration Program, 7 Nov 14

AFI 32-7040,

Air Quality Compliance and Resource Management, 4 Nov 14

AFI 32-7042,

Waste Management, 7 Nov 14

AFI 32-7044,

Storage Tank Environmental Compliance, 18 Aug 15

AFI 32-7047,

Environmental Compliance, Release and Inspection Reporting, 42026

AFI 32-7061,

The Environmental Impact Analysis Process, 12 Mar 03

AFI 32-7062,

Comprehensive Planning, 27 Jun 13

AFI 32-7063,

Air Installations Compatible Use Zones Program, 15 Jul 15

AFI 32-7064,

Integrated Natural Resources Management, 18 Nov 14

AFI 32-7065,

Cultural Resources Management, 19 Nov 14

AFI 32-7086,

Hazardous Materials Management, 4 Feb 15

AFI 35-105,

Community Relations, 26 Jan 10

AFI 35-108,

Environmental Public Affairs, 14 Jul 15

AFI 48-144,

Drinking Water Surveillance Program, 21 Oct 14

AFI 48-145,

Occupational and Environmental Health Program, 22 Jul 14

AFPD 32-70,

Environmental Quality, 20 Jul 94

AFPD 35-1,

Public Affairs Management, 28 Sep 12

AFPD 90-8,

Environment, Safety, and Occupational Health, 2 Feb 12

NFPA 701(2015) Standard Methods of Fire Tests for Flame Propagation of Textiles and Films

U.S. ARMY CORPS OF ENGINEERS (USACE)

EM 385-1-1(2014) Safety and Health Requirements Manual

U.S. ENVIRONMENTAL PROTECTION AGENCY (EPA)

EPA Maximum Achievable Control Technology (MACT) standards EPA Comprehensive Procurement Guidelines (EPA-CPG)

CALIFORNIA CODES AND RULES

8 CCR, Chapter 3.22, Subchapter 2Article 2.6

Asbestos Consultants and Site Surveillance Technicians, 8 CCR §341.15 Certification of Asbestos Consultants and Site Surveillance Technicians

8 CCR, Chapter 4, Subchapter 4 §1529 Asbestos Dusts, Fumes, Mists, Vapors, and Gases, 17 CCR, Division 1, Chapter 8 Accreditation, Certification, and Work Practices for Lead- Based Paint and Lead Hazards

22 CCR, Chapters 10-20§66260-66270, Hazardous Waste Regulation

California Air Resources Board (CARB) Regulations, standards, controls, and portable equipment registration requirements

California Coastal Act Public Resources Code, Division 20

California Assembly Bill AB 939 California Integrated Waste Management Act of 1989

California Assembly Bill AB 32 California Global Warming Solutions Act

South Coast Air Quality Management District (SCAQMD)

Rules & Regulations

California Stormwater Quality Association

Stormwater BMP Manual (2009,)

California Department of Parks and Recreation

Off-Highway Vehicle BMP Manual for Erosion and Sediment Control (2007,)

Western Municipal Water District Permit No: WMWD-006

Sand, Oil & Grease Interceptor

Western Municipal Water District Ordinance 366, Section 3.2.2

Industrial wastewater pollutants

Western Municipal Water District Title 6 Sewer Use Regulations

Regulations For Wastewater Discharge And Sanitary Sewer System Use

MARCH ARB MANAGEMENT PLANS (Most Current Applies)

March ARB does not have a website for contractor use. Contractors must request a copy of Management Plans that are applicable to the work requested from the 452 MSG/CEV (douglas.waters.2@us.af.mil). Either the plan will be emailed or directions provided for receiving a copy. You can also visit the March ARB website to see if the plans are posted in the Environmental Area. https://www.march.afrc.af.mil/

MARB Hazardous Waste Management Plan MARB Facility Response Plan (FRP) MARB Spill Prevention, Control and Countermeasure Plan (SPCC) MARB Integrated Cultural Resource Management Plan (ICRMP) MARB Integrated Natural Resource Plan (INRMP) MARB Air Quality Compliance Management Plan (AQMP) MARB Storm Water Pollution Prevention Plan (SWPPP) MARB Installation Pest Management Plan MARB Integrated Solid Waste Management Plan MARB Asbestos Management Plan MARB Recoverable and Waste Petroleum Products Management Plan MARB Green Procurement Program Plan MARB Hazardous Materials Management Plan MARB Energy Management Plan MARB Facilities Excellence Plan & Standards MARB Environmental Management System (EMS) Guide 2005Hazardous Materials Management;

MARB, Environmental Management Air Emission Inventories;

MARB Fuel Use Monitoring Plan (FUMP) MARB Greenhouse Gas (GHG) Monitoring Plan

1.2 DEFINITIONS

1.2.1 Class I and II Ozone Depleting Substance (ODS)

Class I ODS is defined in Section 602(a) of The Clean Air Act. A list of Class I ODS can be found on the EPA website at the following web link. https://www.epa.gov/ozone-layer-protection/ozone-depleting-substances. Class II ODS is defined in Section 602(s) of The Clean Air Act. A list of Class II ODS can be found on the EPA website at the following weblink.https://www.epa.gov/ozone-layer-protection/ozone-depleting-substances.

1.2.2 Contractor Generated Hazardous Waste

Contractor generated hazardous waste is materials that, if abandoned or disposed of, may meet the definition of a hazardous waste. These waste streams would typically consist of material brought on site by the Contractor to execute work, but are not fully consumed during the course of construction. Examples include, but are not limited to, excess paint thinners (i.e. methyl ethyl ketone, toluene), waste thinners, excess paints, excess solvents, waste solvents, excess pesticides, and contaminated pesticide equipment rinse water.

1.2.3 Electronics Waste

Electronics waste is discarded electronic devices intended for salvage, recycling, or disposal.

1.2.4 Environmental Pollution and Damage

Environmental pollution and damage is the presence of chemical, physical, or biological elements or agents, which adversely affect human health or welfare; unfavorably alter ecological balances of importance to human life; affect other species of importance to humankind; or degrade the environment aesthetically, culturally or historically.

1.2.5 Environmental Protection

Environmental protection is the prevention/control of pollution and habitat disruption that may occur to the environment during any contract activity. The control of environmental pollution and damage requires consideration of land, water, and air; biological and cultural resources; and includes management of visual

Attachment 4

FA466419BA008

mailto:douglas.waters.2@us.af.mil https://www.march.afrc.af.mil/ https://www.epa.gov/ozone-layer-protection/ozone-depleting-substances https://www.epa.gov/ozone-layer-protection/ozone-depleting-substances aesthetics; noise; solid, chemical, gaseous, and liquid waste; radiant energy and radioactive material as well as other pollutants.

1.2.6 Hazardous Debris

As defined in paragraph SOLID WASTE, debris that contains listed hazardous waste (either on the debris surface, or in its interstices, such as pore structure) in accordance with 40 CFR 261. Hazardous debris also includes debris that exhibits a characteristic of hazardous waste in accordance with 40 CFR 261.

1.2.7 Hazardous Materials

Hazardous materials as defined in 49 CFR 171 and listed in 49 CFR 172. Hazardous material is any material that: Is regulated as a hazardous material in accordance with 49 CFR 173; or requires a Safety Data Sheet (SDS) in accordance with 29 CFR 1910.120; or during end use, treatment, handling, packaging, storage, transportation, or disposal meets or has components that meet or have potential to meet the definition of a hazardous waste as defined by 40 CFR 261 Subparts A, B, C, or D. Designation of a material by this definition, when separately regulated or controlled by other sections or directives, does not eliminate the need for adherence to that hazard-specific guidance which takes precedence over this section for "control" purposes. Such material includes ammunition, weapons, explosive actuated devices, propellants, pyrotechnics, chemical and biological warfare materials, medical and pharmaceutical supplies, medical waste and infectious materials, bulk fuels, radioactive materials, and other materials such as asbestos, mercury, and polychlorinated biphenyls (PCBs).

1.2.8 Hazardous Waste

Hazardous Waste is any material that meets the definition of a solid waste and exhibit a hazardous characteristic (ignitability, corrosively, reactivity, or toxicity) as specified in 40 CFR 261, Subpart C, or contains a listed hazardous waste as identified in 40 CFR 261, Subpart D or as defined in California Regulation.

1.2.9 Land Application

Land Application means spreading or spraying discharge water at a rate that allows the water to percolate into the soil. No sheeting action, soil erosion, discharge into storm sewers, discharge into defined drainage areas, or discharge into the "waters of the United States" must occur. Comply with federal, state, and local laws and regulations.

1.2.10 Municipal Separate Storm Sewer System (MS4) Permit

MS4 permits are those held by installations to obtain NPDES permit coverage for their stormwater discharges.

1.2.11 National Pollutant Discharge Elimination System (NPDES) The NPDES permit program controls water pollution by regulating point sources that discharge pollutants into waters of the United States.

1.2.12 Oily Waste

Oily waste are those materials that are, or were, mixed with Petroleum, Oils, and Lubricants (POLs) and have become separated from those POLs. Oily wastes also means materials, including wastewaters, centrifuge solids, filter residues or sludge, bottom sediments, tank bottoms, and sorbents which have come into contact with and have been contaminated by, POLs and may be appropriately tested and discarded in a manner which is in compliance with other state and local requirements. This definition includes materials such as oily rags, "kitty litter" sorbent clay and organic sorbent material. These materials may not be land filled in California. Large quantities of this material, generated from a major spill or in lieu of proper maintenance of the processing equipment, are a solid waste. As a solid waste, perform a hazardous waste determination prior to disposal. As this can be an expensive process, it is recommended that this type of waste be minimized through good housekeeping practices and employee education.

1.2.13 Regulated Waste

Regulated waste are solid wastes that have specific additional federal, state, or local controls for handling, storage, or disposal.

1.2.14 Sediment

Sediment is soil and other debris that have eroded and have been transported by runoff water or wind.

1.2.15 Solid Waste

Solid waste is a solid, liquid, semi-solid or contained gaseous waste. A solid waste can be a hazardous waste, non-hazardous waste, or non-Resource Conservation and Recovery Act (RCRA) regulated waste. Types of solid waste typically generated at construction sites may include:

1.2.16 Debris

Debris is non-hazardous solid material generated during the construction, demolition, or renovation of a structure that exceeds 60 mm (2.5-inch) particle size that is: a manufactured object; plant or animal matter; or natural geologic material (for example, cobbles and boulders), broken or removed concrete, masonry, and rock asphalt paving; ceramics; roofing paper and shingles. Inert materials may be reinforced with or contain ferrous wire, rods, accessories and weldments. A mixture of debris and other material such as soil or sludge is also subject to regulation as debris if the mixture is comprised primarily of debris by volume, based on visual inspection.

1.2.17 Green Waste

Green waste is the vegetative matter from landscaping, land clearing and grubbing, including, but not limited to, grass, bushes, scrubs, small trees and saplings, tree stumps and plant roots. Marketable trees, grasses and plants that are indicated to remain, be re-located, or be re-used are not included.

1.2.18 Material not regulated as solid waste

Material not regulated as solid waste is nuclear source or byproduct materials regulated under the Federal Atomic Energy Act of 1954 as amended; suspended or dissolved materials in domestic sewage effluent or irrigation return flows, or other regulated point source discharges; regulated air emissions; and fluids or wastes associated with natural gas or crude oil exploration or production.

1.2.19 Non-Hazardous Waste

Non-hazardous waste is waste that is excluded from, or does not meet, hazardous waste criteria in accordance with 40 CFR 263 and California, 22 CCR, Chapters 10-20 §66260-66270 .

1.2.20 Recyclables

Recyclables are materials, equipment and assemblies such as doors, windows, door and window frames, plumbing fixtures, glazing and mirrors that are recovered and sold as recyclable, wiring, insulated/non-insulated copper wire cable, wire rope, and structural components. It also includes commercial-grade refrigeration equipment with Freon removed, household appliances where the basic material content is metal, clean polyethylene terephthalate bottles, textiles, high-grade paper products and corrugated cardboard, stackable pallets in good condition, clean crating material, and clean rubber/vehicle tires. Metal meeting the definition of lead contaminated or lead based paint contaminated may not be included as recyclable if sold to a scrap metal company.

1.2.21 Surplus Soil

Surplus soil is existing soil that is in excess of what is required for this work, including aggregates intended, but not used, for on-site mixing of concrete, mortars, and paving. Contaminated soil meeting the definition of hazardous material or hazardous waste is not included and must be managed in accordance with paragraph HAZARDOUS MATERIAL MANAGEMENT and SCAQMD rules regarding soils containing VOCs and other petroleum products.

1.2.22 Scrap Metal

This includes scrap and excess ferrous and non-ferrous metals such as reinforcing steel, structural shapes, pipe, and wire that are recovered or collected and disposed of as scrap. Scrap metal meeting the definition of hazardous material or hazardous waste is not included. Dental waste metals are not included and must be handled in accordance with California law

1.2.23 SURFACE DISCHARGE

Surface discharge means discharge of water into drainage ditches, storm sewers, creeks or "waters of the United States". Surface discharges are discrete, identifiable sources and require a permit from the governing agency.

Comply with federal, state, and local laws and regulations.

1.2.24 STORMWATER

Stormwater is any precipitation in an urban or suburban area that does not evaporate or soak into the ground, but instead collects and flows into storm drains, rivers, and streams.

1.2.25 Wood

Wood is dimension and non-dimension lumber, plywood, chipboard, hardboard. Treated or painted wood that meets the definition of lead contaminated or lead based contaminated paint or other hazardous materials defined by the State of California (e.g. creosol) is not included. Treated wood includes, but is not limited to, lumber, utility poles, crossties, and other wood products with chemical treatment.

1.2.26 Wastewater

Wastewater is the used water and solids from a community that flow to a treatment plant.

1.2.27 Waters of the United States

Waters of the United States means Federally jurisdictional waterbodies, including wetlands that are subject to regulation under Section 404 of the Clean Water Act or navigable waterbodies, as defined under the Rivers and Harbors Act.

1.2.28 Wetlands

Wetlands are those areas that are inundated or saturated by surface or groundwater at a frequency and duration sufficient to support, and that under normal circumstances do support, a prevalence of vegetation typically adapted for life in saturated soil conditions.

1.2.29 Universal Waste

The universal waste regulations streamline collection requirements for certain hazardous wastes in the following categories: batteries, pesticides, mercury-containing equipment (for example, thermostats), and lamps (for example, fluorescent bulbs). The rule is designed to reduce hazardous waste in the municipal solid waste (MSW) stream by making it easier for universal waste handlers to collect these items and send them for recycling or proper disposal. These regulations can be found at 40 CFR 273 and 22 CCR, Chapters 10-20 §66260-66270.

1.3 SUBMITTALS

The following submittals are required to be delivered as indicated to the Contracting Officer. Government approval is required for submittals with a "G" designation; submittals not having a "G" designation are for information only. When used, a designation following the "G" designation identifies the office that will review the submittal for the Government. The Contractor shall submit through the KO, the following to 452 MSG/CEV and their designated agency as and if specified in other sections of the specification. Submit the following in accordance with the statement of work or if included Section 01 33 00 SUBMITTAL PROCEDURES:

1.3.1 SD-01 Pre-contract Submittals – all preconstruction/pre-contract start work submittals shall be submitted as part of the environmental protection plan (EPP) 10 days prior to the start of any activities on March ARB as discussed below:

1.3.1.1 Environmental protection plan (EPP) (see paragraph 1.4 of this section) the contractor shall provide their EPP for approval to 452 MSG/CEV, 10 days prior to the start of any activities on March ARB. A dig/work permit, March ARB form 103, will not be signed by CEV without prior approval of this document. A template EPP is attached to this guide specification and must be followed. The EPP shall contain the following documents, unless it is clearly explained why the documents are not required in the EPP; G , CEV.

1.3.1.2 Draft documents for application of stormwater notice of intent to include a draft stormwater pollution prevention plan (SWPPP), if required by the state water board and land disturbance is greater than 1 acre (upon approval, contractor shall submit documents into the state computer program storm as directed by CEV)

1.3.1.3 Erosion and sediment control certificate (required for disturbance less than 1 acre) to be included in the EPP and must also be attached for approval with the dig/work permit (march arb form 103) submittal as specified in the statement of work;

1.3.1.4 Employee training records to be included in the EPP (as required and as described in the EPP);

1.3.1.5 Environmental manager qualifications to be included in the EPP (as required and as described in the

EPP);

1.3.1.6 Hazardous waste management plan to be included in the EPP (as required and as described in the

EPP).

1.3.1.7 Solid waste management plan to be included in the EPP (as required and as described in the EPP)

1.3.1.8 Erosion and sediment control inspector qualifications to be included in the EPP (as required and as described in the EPP);

1.3.1.9 Regulatory notifications to be included in the EPP (as required and as described in the EPP);

1.3.1.10

1.3.1.11 SD-06 Test Reports

1.3.1.12 Laboratory Analysis if required for work to be accomplished as outlined in EPP; G, CEV

1.3.1.13 Inspection Reports if required for work to be accomplished as outlined in EPP; G, CEV

1.3.1.14 Solid Waste Management Report as outlined in EPP; G , CEV

1.3.1.15 SD-07 Certificates

1.3.1.16 Permit Applications as outlined in EPP (SCAQMD, DTSC, Etc.); G, CEV

1.4 SD-11 CLOSEOUT SUBMITTALS

1.4.1 Stormwater Pollution Prevention Plan Compliance Notebook as required by State Water

Board; G, CEV

1.4.2 Stormwater Notice of Termination (for NPDES coverage under the general permit for construction activities); G, CEV

1.4.3 Environmental Records Binder to include, if applicable to work required: G, CEV

1.4.3.1 Waste Determination Documentation as outlined in EPP; G, CEV

1.4.3.2 Disposal Documentation for Hazardous and Regulated Waste; G, CEV

1.4.3.3 Assembled Employee Training Records as outlined in EPP; G,

1.4.3.4 Solid Waste Management Report as outlined in EPP; G, CEV

1.4.3.5 Contractor Hazardous Material Inventory Log as outlined in EPP; G, CEV

1.4.3.6 Hazardous Waste/Debris Management Documentation as outlined in EPP; G, CEV

1.4.3.7 Regulatory Notifications as outlined in EPP; G, CEV

1.4.3.8 Monthly Hazardous Material (HAZMAT) usage totals (paragraph 1.08.C). G, CEV

1.4.3.9 HAZMAT Business Plan or HAZMAT Disclaimer, (paragraph 1.08.D). G, CEV

1.4.3.10 The contractor shall provide weigh tickets to the CO monthly, copy to CEV, for disposal of construction debris and/or recycled materials (i.e. metal doors, aluminum frames, wood doors, etc.) per UFGS Section 01 74 19, specifically for C&D Waste Management (Section 01 74 19) in the Whole Building Design Guide: http://www.wbdg.org/ for additional information. Click on the UFGS tab on the right side for requirements. G, CEV

1.4.3.11 Form for installation of an internal combustion engine, or fuel storage tank. G, CEV

1.4.3.12 Any logs or records required by SCAQMD for Application to construct and/or Permit to Operate as applicable G, CEV

1.4.4 Aboveground Storage Tank - technical information G, CEV

1.4.5 A Recovered Materials Determination Form (RMDF) (paragraph B). G, CEV

1.4.6 An Estimate of Percentage of Recovered Material Content for EPA-Designated Products

(paragraph D G, CEV

1.4.7 Meter Logs for Generators and certification of meter reading at turn over/Commissioning

1.4.8 HVAC Maintenance Manual; G, CEV/CECC

1.4.9 Refrigerant Log; G, CEV

1.5 ENVIRONMENTAL PROTECTION REQUIREMENTS

General:

Provide and maintain, during the life of the contract, environmental protection as defined in this specification.

Plan for and provide environmental protective measures to control pollution that develops during contract practice. Plan for and provide environmental protective measures required to correct conditions that develop during the contract of permanent or temporary environmental features associated with the project. Protect the environmental resources within the project boundaries and those affected outside the limits of permanent work during the entire duration of this Contract. Comply with federal, state, and local regulations pertaining to the environment, including water, air, solid waste, hazardous waste and substances, oily substances, and noise pollution. Tests and procedures assessing whether contract operations comply with Applicable Environmental Laws may be required. Analytical work must be performed by qualified laboratories; and where required by law, the laboratories must be certified.

The work covered by this section consists of furnishing all labor, materials, equipment, and performing all work as specified in the Statement of Work (SOW) and as required for the prevention of environmental pollution during and as the result of performing the work under this contract. For the purpose of this specification, environmental pollution is defined as the presence of chemical, physical, or biological elements or agents, which adversely affect human life; affect other species of importance to staff; or degrade the ability of the environment for aesthetic and recreational purposes. The control of environmental pollution requires consideration of air, water, and land, and involves noise, solid waste-management and management of radiant energy, hazardous materials, radioactive materials, as well as other pollutants.

Contractor, and any subcontractors, shall comply with the most stringent Federal, state, and local environmental laws, regulations, and Air Force policies, instructions, and plans. The federal government is not exempt from compliance with State and local environmental regulations. The Contractor shall maintain an awareness of changing environmental regulatory requirements to avoid environmental deficiencies for activities on March ARB.

In order to prevent, and to provide for abatement and control of, any environmental pollution arising from the contract activities of the Contractor in the performance of this contract, Contractors shall comply with all applicable Federal, State, and local laws and regulations, and installation regulations concerning environmental pollution control and abatement.

Contractor shall be provided a copy of the AF 813 NEPA document. In accordance with NEPA, contractor may not perform work beyond the scope or restrictions described in the NEPA document, unless NEPA document is modified and signed again.

The Contracting Officer will notify the Contractor in writing of any noncompliance with the foregoing provisions and the action to be taken. The Contractor shall, after receipt of such notice, immediately take corrective action.

1.6 CONFORMANCE WITH THE ENVIRONMENTAL MANAGEMENT SYSTEM

Perform work under this contract consistent with the policy and objectives identified in the installation's Environmental Management System (EMS) (Currently under development). Compliance is made by compliance with this specification.

1.7 SPECIAL ENVIRONMENTAL REQUIREMENTS

Comply with the special environmental requirements listed here and attached at the end of this section.

1.7.1 Environmental Coordination:

The 452nd Mission Support Group, Base Civil Engineer, Environmental Flight (/CEV) is the single point of contact for coordination with all environmental regulatory agencies. Prior to coordinating with any environmental regulatory agency, the contractor shall obtain approval from CEV. The Contractor shall provide copies of any regulatory agency notification, report, consultation, permit, and/or regulatory document to CEV.

The Contractor shall comply with all permit conditions and consultation requirements. The Contractor shall provide all required testing analysis and monitoring.

1.7.2 Environmental Planning:

The Contractor shall comply with all testing, monitoring, record keeping, reporting, mitigation, and protection measure requirements resulting from the National Environmental Policy Act (NEPA), the Environmental Impact Analysis Process (EIAP), and the March ARB AF form 332-project approval process. The contractor must keep a copy of the decision document (AF 813, Finding of No Significant Impact or Record of Decision) on file and deviation from the Description of the Proposed Action is not permitted without a revision of the decision document. For most contracts this process is completed before award of the contract, however, for on-going projects, which receive tasks from the government such as service, maintenance or repair work, the task may need NEPA approval before work may proceed. The Contractor must maintain a copy of any revisions to the NEPA decision document and advice the Contracting Officer of work, which may beyond the authorization for written approval.

1.7.3 Environmental Audits/Inspections:

The Contractor shall support the government with all federal, state, local, and Air Force environmental inspections, audits, or assessments.

1.7.4 Notices of Violations (NOV):

The Contractor shall be liable for any Notices of Violation (NOV), enforcement action, fine, penalty, and/or corrective action imposed by federal, state, or local environmental regulatory agencies for activities under the Contractor’s control. The Contractor shall provide verbal notification to 452 MSG/CEV and the Contracting Officer within 24-hours of receiving an NOV followed by written notification within three (3) working days.

1.8 QUALITY ASSURANCE

1.8.1 Pre-contract Start Survey and Protection of Features

Prior to start of any onsite contract activities, perform a Pre-contract Start Survey of the project site, and take photographs showing existing environmental conditions in and adjacent to the site. Include findings in the EPP.

Include features requiring protection under the provisions of the Contract Clauses, which are not specifically identified on the drawings as environmental features requiring protection along with the condition of trees, shrubs and grassed areas immediately adjacent to the site of work and adjacent to the Contractor's assigned storage area and access route(s), as applicable. Protect those environmental features included and any indicated on the drawings, regardless of interference that their preservation may cause to the work under the Contract.

1.8.2 Regulatory Notifications

Provide regulatory notification requirements after approval by CEV in accordance with federal, state and local regulations. Submit copies of regulatory notifications to the Contracting Officer at least [20] days prior to commencement of activities requiring notification for CEV approval. Typically, regulatory notifications must be provided for the following (this listing is not all-inclusive): demolition, renovation, NPDES defined site work, construction, removal or use of a permitted air emissions source, and remediation of controlled substances (asbestos, hazardous waste, lead paint).

1.8.3 Environmental Brief/Pre-Installation Conference

Prior to commencement of the work, the Contractor shall meet with the installation environmental office (452 MSG/CEV) representatives and the Contracting Officer (KO) to develop mutual understandings relative to compliance with this provision and administration of the environmental pollution control program and the Environmental Protection Plan (EPP). This may be conducted at a pre-contract start conference held by the KO.

At a minimum, a draft Environmental Protection Plan, using the template provided and attached to this specification, shall be provided 5 days before the meeting for review and discussion at the meeting. Develop a mutual understanding relative to the details of environmental protection, including measures for protecting natural and cultural resources, required reports, required permits, permit requirements (such as mitigation measures), and other measures to be taken.

1.8.4 Environmental Manager

Appoint in writing an Environmental Manager for the project site. The Environmental Manager is directly responsible for coordinating contractor compliance with federal, state, local, and installation requirements. The Environmental Manager must ensure compliance with Hazardous Waste Program requirements (including hazardous waste handling, storage, manifesting, and disposal); implement the EPP; ensure environmental permits are obtained, maintained, and closed out; ensure compliance with Stormwater Program requirements; ensure compliance with Hazardous Materials (storage, handling, and reporting) requirements; and coordinate any remediation of regulated substances (lead, asbestos, PCB transformers). This position can be a collateral position. However, the person in this position must have certification of training in the following areas based on the scope of the work and Environmental Manager Qualifications shall be submitted in the EPP:

1.8.4.1 Hazardous material and waste management if hazardous materials will be brought on base or generated during the contract, of at least an 8 hour course. Training or experience must show the ability to accomplish the following duties: ensure waste segregation and storage compatibility requirements are met; inspect and manage Satellite Accumulation areas; ensure only authorized personnel add wastes to containers; ensure Contractor personnel are trained in 40 CFR requirements in accordance with their position requirements; coordinate removal of waste containers; manage manifests and required documentation,

1.8.4.2 Erosion and sediment control best practices of at least 8 hours if ground disturbance id over 1 acre or an online course if less than 1 acre

1.8.4.3 Specialized training in asbestos containing materials lead based paints or PCBs if work specified include these materials as required by the March ARB Asbestos Management Plan.

1.8.4.4 Training in the subject matter of any environmental permits required in the contract.

1.8.5 Employee Training Records

Prepare and maintain Employee Training Records throughout the term of the contract meeting applicable 40 CFR requirements. Provide Employee Training Records in the Environmental Records Binder. Ensure every employee completes a program of classroom instruction or on-the-job training that teaches him or her to perform their duties in a way that ensures compliance with federal, state and local regulatory requirements for RCRA Large Quantity Generator. Provide a Position Description for each employee, by subcontractor, based on the Davis-Bacon Wage Rate designation or other equivalent method, evaluating the employee's association with hazardous and regulated wastes. This Position Description will include training requirements as defined in 40 CFR 265 for a Large Quantity Generator facility. Submit these Assembled Employee Training Records to the Contracting Officer at the conclusion of the project, unless otherwise directed.

Train personnel to meet California requirements. Conduct environmental protection/pollution control meetings for personnel prior to commencing contract activities. Conduct additional meetings for new personnel and when site conditions change. Include in the training and meeting agenda: methods of detecting and avoiding pollution;

familiarization with statutory and contractual pollution standards; installation and care of devices, vegetative covers, and instruments required for monitoring purposes to ensure adequate and continuous environmental protection/pollution control; anticipated hazardous or toxic chemicals or wastes, and other regulated contaminants; recognition and protection of archaeological sites, artifacts, waters of the United States, and endangered species and their habitat that are known to be in the area. Provide a copy of the Erosion and Sediment Control Inspector Qualifications as defined by EPA and Certification as required by the State of California

1.8.6 Non-Compliance Notifications

The Contracting Officer will notify the Contractor in writing of any observed noncompliance with federal, state or local environmental laws or regulations, permits, and other elements of the Contractor's EPP. After receipt of such notice, inform the Contracting Officer of the proposed corrective action and take such action when approved by the Contracting Officer. The Contracting Officer may issue an order stopping all or part of the work until satisfactory corrective action has been taken. No time extensions will be granted or equitable adjustments allowed for any such suspensions. This is in addition to any other actions the Contracting Officer may take under the contract, or in accordance with the Federal Acquisition Regulation or Federal Law

1.9 ENVIRONMENTAL PROTECTION PLAN (EPP) REQUIREMENTS

The purpose of the EPP is to present an overview of known or potential environmental issues that must be considered and addressed during contract efforts based on the work required in the PWS. Contractor shall meet (See Section 1.6.4) with the Contracting Officer or Contracting Officer Representative, who will invite the required Environmental Office representatives to discuss the EPP and develop a mutual understanding relative to the details for environmental protection including required reports, and other measures. The attached EPP Template will be reviewed and questions answered as to required inserts by the Contractor. A complete EPP shall be submitted for approval by CEV, by the Contractor, within 15 days from the meeting and not less than 10 days before start of work, whichever is sooner. Contractor shall revise the EPP prior to start of work and throughout the project to include any reporting requirements, changes in site conditions, or contract modifications that change the project scope of work in a way that could have an environmental impact and submit to the Contracting Officer, for approval by CEV. No requirement in this section will relieve the Contractor of any applicable federal, state, and local environmental protection laws and regulations. During contract execution contractor shall, identify, implement, and submit for approval any additional requirements to be included in the EPP. Contractor shall maintain the current version onsite.

The EPP shall include, but is not limited to, the following elements:

1.9.1 General:

1.9.1.1 Descriptions

The Contractor shall insert in the template a short description of the project to include, at a minimum, a brief description of how they will meet environmental compliance requirements. The EPP shall address:

the contractor’s methods, procedures, and practices pertaining to air quality emissions, ozone depleting substances (ODS), greenhouse gases (GHG), water quality standards, waste water permit requirements, storm water, cultural resources, natural resource protection, storage tanks, applicable laws pertaining to construction and materials, hazardous waste management, hazardous materials management, spill/release management, recycled/recovered materials and use, solid waste, construction debris management, PCBs, lead-based paint, asbestos management, Contractor combustion source equipment, California Air Resource Board registration and permits as applicable to this contract. This section shall not exceed one page in length.

1.9.1.2 Duties

Contractor shall provide in paragraph 2 of template:

the duties of its personnel…