UFGS 08 71 00 revised 21 Aug 24.pdf

{Repair Bunch Hall Dorm B221 - Grand Forks AFB, ND} {JFSD201151}

SECTION 08 71 00

DOOR HARDWARE

02/16

PART 1 GENERAL

1.1 RELATED WORK SPECIFIED ELSEWHERE

Certain Hardware for Aluminum Doors 08 11 16

1.2 REFERENCES

The publications listed below form a part of this specification to the extent referenced. The publications are referred to within the text by the basic designation only.

ASTM INTERNATIONAL (ASTM)

ASTM E283 (2019) Standard Test Method for Determining the Rate of Air Leakage Through Exterior Windows, Curtain Walls, and Doors Under Specified Pressure Differences Across the Specimen

BUILDERS HARDWARE MANUFACTURERS ASSOCIATION (BHMA)

ANSI/BHMA A156.1 (2016) Butts and Hinges

ANSI/BHMA A156.2 (2017) Bored and Preassembled Locks and Latches

ANSI/BHMA A156.3 (2014) Exit Devices

ANSI/BHMA A156.4 (2013) Door Controls - Closers

ANSI/BHMA A156.5 (2020) Cylinder and Input Devices for Locks

ANSI/BHMA A156.6 (2015) Architectural Door Trim

ANSI/BHMA A156.7 (2016) Template Hinge Dimensions

ANSI/BHMA A156.13 (2017) Mortise Locks & Latches Series 1000

ANSI/BHMA A156.16 (2018) Auxiliary Hardware

ANSI/BHMA A156.18 (2016) Materials and Finishes

ANSI/BHMA A156.21 (2019) Thresholds

ANSI/BHMA A156.22 (2017) Door Gasketing and Edge Seal Systems

ANSI/BHMA A156.26 (2012) Continuous Hinges

ANSI/BHMA A156.36 (2010) Auxiliary Locks

SECTION 08 71 00 Page 1

Revised 21 Aug 24

NATIONAL FIRE PROTECTION ASSOCIATION (NFPA)

NFPA 72 (2019; TIA 19-1; ERTA 1 2019) National Fire Alarm and Signaling Code

NFPA 80 (2019) Standard for Fire Doors and Other Opening Protectives

NFPA 101 (2021) Life Safety Code

NFPA 252 (2017) Standard Methods of Fire Tests of Door Assemblies

STEEL DOOR INSTITUTE (SDI/DOOR)

SDI/DOOR A250.8 (2017) Specifications for Standard Steel Doors and Frames

U.S. NATIONAL ARCHIVES AND RECORDS ADMINISTRATION (NARA)

36 CFR 1191 Americans with Disabilities Act (ADA) Accessibility Guidelines for Buildings and Facilities; Architectural Barriers Act (ABA) Accessibility Guidelines

UNDERWRITERS LABORATORIES (UL)

UL Bld Mat Dir (updated continuously online) Building Materials Directory

1.3 SUBMITTALS

Government approval is required for submittals with a "G" designation;

submittals not having a "G" designation are for information only. When used, a designation following the "G" designation identifies the office that will review the submittal for the Government. Submit the following in accordance with Section 01000:

SD-02 Shop Drawings

Manufacturer's Detail Drawings; G

Verification of Existing Conditions; G

Hardware Schedule; G

Keying System; G

SD-03 Product Data

Hardware Items; G

SD-08 Manufacturer's Instructions

Installation

SD-10 Operation and Maintenance Data

Hardware Schedule Items, Data Package 1; G

SECTION 08 71 00 Page 2

SD-11 Closeout Submittals

Key Bitting

1.4 SHOP DRAWINGS

Submit manufacturer's detail drawings indicating all hardware assembly components and interface with adjacent construction. Base shop drawings on verified field measurements and include verification of existing conditions.

1.5 PRODUCT DATA

Indicate fire-ratings at applicable components. Provide documentation of ABA/ADA accessibility compliance of applicable components, as required by 36 CFR 1191 Appendix D - Technical.

1.6 HARDWARE SCHEDULE

Prepare and submit hardware schedule in the following form:

Hardware Item

Quantity Size Reference Publi-cation Type No.

Finish Mfr Name and Catalog No.

Key Control Symbols

UL

Mark (If fire-rated and listed)

BHMA

Finish Desig-nation

In addition, submit hardware schedule data package 1 in accordance with Section 01000:

1.7 KEY BITTING CHART REQUIREMENTS

1.7.1 Requirements

Submit key bitting charts to the Contracting Officer prior to completion of the work. Include:

a. Complete listing of all keys (e.g. AA1 and AA2).

b. Complete listing of all key cuts (AA1-123456, AA2-123458).

c. Tabulation showing which key fits which door.

d. Copy of floor plan showing doors and door numbers.

e. Listing of 20 percent more key cuts than are presently required in each master system.

1.8 QUALITY ASSURANCE

1.8.1 Hardware Manufacturers and Modifications

Provide, as far as feasible, locks, hinges and closers of one lock, hinge, or closer manufacturer's make. Modify hardware as necessary to provide features indicated or specified.

SECTION 08 71 00 Page 3

1.8.2 Key Shop Drawings Coordination Meeting

Prior to the submission of the key shop drawing, the Contracting Officer, Contractor, Door Hardware Subcontractor, using Activity and Base Locksmith must meet to discuss and coordinate key requirements for the facility.

1.9 DELIVERY, STORAGE, AND HANDLING

Deliver hardware in original individual containers, complete with necessary appurtenances including fasteners and instructions. Mark each individual container with item number as shown on hardware schedule. Deliver permanent keys and removable cores to the Contracting Officer, either directly or by certified mail. Deliver construction master keys with the locks.

PART 2 PRODUCTS

2.1 TEMPLATE HARDWARE

Hardware applied to metal or to prefinished doors must be manufactured using a template. Provide templates to door and frame manufacturers in accordance with ANSI/BHMA A156.7 for template hinges. Coordinate hardware items to prevent interference with other hardware.

2.2 HARDWARE FOR FIRE DOORS AND EXIT DOORS

Provide all hardware necessary to meet the requirements of NFPA 72 for door alarms, NFPA 80 for fire doors, NFPA 101 for exit doors, NFPA 252 for fire tests of door assemblies, ABA/ADA accessibility requirements, and all other requirements indicated, even if such hardware is not specifically mentioned in paragraph HARDWARE SCHEDULE. Provide Underwriters Laboratories, Inc. labels for such hardware in accordance with UL Bld Mat Dir or equivalent labels in accordance with another testing laboratory approved in writing by the Contracting Officer.

2.3 HARDWARE ITEMS

Clearly and permanently mark with the manufacturer's name or trademark, hinges, pivots, locks, latches, exit devices, bolts and closers where the identifying mark is visible after the item is installed. For closers with covers, the name or trademark may be beneath the cover.

2.3.1 Hinges

Provide in accordance with ANSI/BHMA A156.1. Provide hinges that are 4-1/2 by 4-1/2 inch unless otherwise indicated. Construct loose pin hinges for interior doors and reverse-bevel exterior doors so that pins are non-removable when door is closed. Other anti-friction bearing hinges may be provided in lieu of ball bearing hinges.

2.3.2 Continuous Hinges

Where continuous hinges are required, provide in accordance with

ANSI/BHMA A156.26.

2.3.3 Locks and Latches

At exterior locations, provide locksets of full stainless steel type 302 or

SECTION 08 71 00 Page 4

304 construction including fronts, strike, escutcheons, knobs, bolts and all interior working parts. Marine Grade I, fully non-ferrous.

2.3.3.1 Mortise Locks and Latches

Provide in accordance with ANSI/BHMA A156.13, Series 1000, Operational Grade 1, Security Grade 2. Provide mortise locks with escutcheons not less than 7 by 2-1/4 inch with a bushing at least 1/4 inch long. Cut escutcheons to fit cylinders and provide trim items with straight, beveled, or smoothly rounded sides, corners, and edges. Provide knobs of mortise locks with screwless shanks and no exposed screws.

2.3.3.2 Bored Locks and Latches

Provide in accordance with ANSI/BHMA A156.2, Series 4000, Grade 1.

2.3.3.3 Auxiliary Locks

Provide in accordance with ANSI/BHMA A156.36, Grade 1.

2.3.4 Exit Devices

Provide in accordance with ANSI/BHMA A156.3, Grade 1. Provide adjustable strikes for rim type and vertical rod devices. Provide open back strikes for pairs of doors with mortise and vertical rod devices. Provide touch bars in lieu of conventional crossbars and arms.

Use stainless steel or bronze base metal with plated finishes. Also include stainless steel fasteners and screws.

2.3.5 Cylinders and Cores

Provide cylinders and cores for new locks. Provide cylinders from the products of one manufacturer, and provide cores from the products of one manufacturer. Rim cylinders, mortise cylinders, and knobs of bored locksets have interchangeable cores which are removable by special control keys. Stamp each interchangeable core with a key control symbol in a concealed place on the core.

2.3.6 Keying System

Provide a master keying system. Provide a construction master keying system.

Provide key cabinet as specified.

The Government will install contractor-provided cores. Provide cylinders of Grade 1 products from one manufacturer. Notify the Contracting Officer 90 days prior to the required delivery of the cylinders. Provide temporary cores and keys for the Contractor's use during construction, and for testing of locksets.

2.3.7 Lock Trim

Provide cast, forged, or heavy wrought construction and commercial plain design for lock trim.

2.3.7.1 Lever Handles

Provide lever handles. Provide in accordance with ANSI/BHMA A156.3 for

SECTION 08 71 00 Page 5

Revised 21 Aug 24

SturdevantG Line mortise locks of lever handles for exit devices. Provide lever handle locks with a breakaway feature (such as a weakened spindle or a shear key) to prevent irreparable damage to the lock when force in excess of that specified in ANSI/BHMA A156.13 is applied to the lever handle. Provide lever handles return to within 1/2 inch of the door face.

2.3.8 Keys

Provide one file key, one duplicate key, and one working key for each key change and for each master keying system. Provide one additional working key for each lock of each keyed-alike group. Provide two additional keys for each sleeping room. Provide 6 grand master keys, 6 construction master keys, and 10 control keys for removable cores. Provide a quantity of key blanks equal to 20 percent of the total number of file keys. Stamp each key with appropriate key control symbol and "U.S. property - do not duplicate." Do not place room number on keys.

2.3.9 Door Bolts

Provide in accordance with ANSI/BHMA A156.16. Provide dustproof strikes for bottom bolts, except at doors having metal thresholds. Provide automatic latching flush bolts in accordance with ANSI/BHMA A156.3, Type 25.

2.3.10 Closers

Provide in accordance with ANSI/BHMA A156.4, Series C02000, Grade 1, with PT 4C. Provide with brackets, arms, mounting devices, fasteners, full size covers and other features necessary for the particular application. Size closers in accordance with manufacturer's printed recommendations, or provide multi-size closers, Sizes 1 through 6, and list sizes in the Hardware Schedule. Provide manufacturer's 10 year warranty.

Use stainless steel inside bracketed or door mounted closers on exterior doors. On interior doors use closers of 302 or 304 stainless steel or non-ferrous materials. On surface-mounted closers use or apply rust inhibiting finish on all ferrous parts. Also apply this finish on concealed closers.

2.3.10.1 Identification Marking

Engrave each closer with manufacturer's name or trademark, date of manufacture, and manufacturer's size designation in locations that will be visible after installation.

2.3.11 Door Protection Plates

Provide in accordance with ANSI/BHMA A156.6.

2.3.11.1 Sizes

2 inch less than door width for single doors; 1 inch less than door width for pairs of doors. Provide 8 inch kick plates for flush doors. Provide a minimum 36 inch armor plates for flush doors, except 16 inch high armor plates on fire doors.

2.3.12 Door Stops and Silencers

Provide in accordance with ANSI/BHMA A156.16. Silencers Type L03011.

Provide three silencers for each single door, two for each pair.

SECTION 08 71 00 Page 6

2.3.13 Thresholds

Provide in accordance with ANSI/BHMA A156.21. Use J35100, with vinyl or silicone rubber insert in face of stop, for exterior doors opening out, unless specified otherwise.

2.3.14 Weatherstripping Gasketing

Provide in accordance with ANSI/BHMA A156.22. Provide the type and function designation where specified in paragraph HARDWARE SCHEDULE.

Provide a set to include head and jamb seals, sweep strips, and, for pairs of doors, astragals. Air leakage of weatherstripped doors not to exceed 0.5 cubic feet per minute of air per square foot of door area when tested in accordance with ASTM E283. Provide weatherstripping with one of the following:

2.3.14.1 Extruded Aluminum Retainers

Extruded aluminum retainers not less than 0.050 inch wall thickness with vinyl, neoprene, silicone rubber, or polyurethane inserts. Provide clear anodized aluminum.

2.3.14.2 Interlocking Type

Zinc or bronze not less than 0.018 inch thick.

2.3.14.3 Spring Tension Type

Spring bronze or stainless steel not less than 0.008 inch thick.

2.3.15 Rain Drips

Provide in accordance with ANSI/BHMA A156.22. Provide extruded aluminum rain drips, not less than 0.08 inch thick, bronze anodized finish. Provide the manufacturer's full range of color choices to the Contracting Officer for color selection. Set drips in sealant and fasten with stainless steel screws.

2.3.15.1 Overhead Rain Drips

Approximately 1-1/2 inch high by 2-1/2 inch projection. Align bottom with door frame rabbet.

2.3.16 Auxiliary Hardware (Other than locks)

Provide in accordance with ANSI/BHMA A156.16, Grade 1.

2.3.17 Special Tools

Provide special tools, such as spanner and socket wrenches and dogging keys, as required to service and adjust hardware items.

2.4 FASTENERS

Provide fasteners of type, quality, size, and quantity appropriate to the specific application. Fastener finish to match hardware. Provide stainless steel or nonferrous metal fasteners in locations exposed to weather. Verify metals in contact with one another are compatible and will

SECTION 08 71 00 Page 7 avoid galvanic corrosion when exposed to weather.

2.5 FINISHES

Provide in accordance with ANSI/BHMA A156.18. Provide hardware in BHMA 630 finish (satin stainless steel), unless specified otherwise. Provide items not manufactured in stainless steel in BHMA 626 finish (satin chromium plated) over brass or bronze, except aluminum paint finish for surface door closers. Match exposed parts of concealed closers to lock and door trim.

Match hardware finish for aluminum doors to the doors.

2.6 KEY CABINET AND CONTROL SYSTEM

Provide in accordance with ANSI/BHMA A156.5, E8341 (125 hooks).

PART 3 EXECUTION

3.1 INSTALLATION

Provide hardware in accordance with manufacturers' printed installation instructions. Fasten hardware to wood surfaces with full-threaded wood screws or sheet metal screws. Provide machine screws set in expansion shields for fastening hardware to solid concrete and masonry surfaces.

Provide toggle bolts where required for fastening to hollow core construction. Provide through bolts where necessary for satisfactory installation.

3.1.1 Weatherstripping Installation

Provide full contact, weathertight seals that allow operation of doors without binding the weatherstripping.

3.1.1.1 Stop Applied Weatherstripping

Fasten in place with color matched sheet metal screws not more than 9 inch on center after doors and frames have been finish painted.

3.1.1.2 Interlocking Type Weatherstripping

Provide interlocking, self adjusting type on heads and jambs and flexible hook type at sills. Nail weatherstripping to door 1 inch on center and to heads and jambs at 4 inch on center.

3.1.1.3 Spring Tension Type Weatherstripping

Provide spring tension type on heads and jambs. Provide bronze nails with bronze. Provide stainless steel nails with stainless steel. Space nails not more than 1-1/2 inch on center.

3.1.2 Threshold Installation

Extend thresholds the full width of the opening and notch end for jamb stops. Set thresholds in a full bed of sealant and anchor to floor with cadmium-plated, countersunk, steel screws in expansion sleeves. For aluminum thresholds placed on top of concrete surfaces, coat the underside surfaces that are in contact with the concrete with fluid applied waterproofing as a separation measure prior to placement.

SECTION 08 71 00 Page 8

3.2 FIRE DOORS AND EXIT DOORS

Provide hardware in accordance with NFPA 72 for door alarms, NFPA 80 for fire doors, NFPA 101 for exit doors, and NFPA 252 for fire tests of door assemblies.

3.3 HARDWARE LOCATIONS

Provide in accordance with SDI/DOOR A250.8, unless indicated or specified otherwise.

a. Kick and Armor Plates: Push side of single-acting doors. Both sides of double-acting doors.

b. Mop Plates: Bottom flush with bottom of door.

3.4 KEY CABINET AND CONTROL SYSTEM

Locate where directed. Tag one set of file keys and one set of duplicate keys. Place other keys in appropriately marked envelopes, or tag each key. Provide complete instructions for setup and use of key control system. On tags and envelopes, indicate door and room numbers or master key.

3.5 FIELD QUALITY CONTROL

After installation, protect hardware from paint, stains, blemishes, and other damage until acceptance of work. Submit notice of testing 15 days before scheduled, so that testing can be witnessed by the Contracting Officer. Adjust hinges, locks, latches, bolts, holders, closers, and other items to operate properly. Demonstrate that permanent keys operate respective locks, and give keys to the Contracting Officer. Correct, repair, and finish, errors in cutting and fitting and damage to adjoining work.

3.6 HARDWARE SETS

Provide certain hardware for aluminum doors under this section. Deliver Hardware templates and hardware, except field applied hardware, to the aluminum door and frame manufacturer for use in fabricating doors and frames.

3.6.1 List of Manufacturers

Where a manufacturer's name or model number is provided, it is intended to represent the Basis of Design only. Products from other manufacturers or other product models may be provided subject to meeting all applicable specification requirements.

Specified Equal Hinges Stanley Hager, McKinney Continuous Hinges Pemko McKinney, ABH Cylinders Best 6 Pin Locks Best Corbin-Russwin, Schlage Exit Devices Precision Sargent, Corbin Russwin Closers Best Norton, Sargent, Corbin Russwin Overhead Stops Rixson ABH, Rockwood, Sargent Flat Goods and Stops Rockwood Trimco Weatherproofing Pemko National Guard

SECTION 08 71 00 Page 9

Revised 21 Aug 24

SturdevantG Line

HARDWARE SET 1

1½ Pairs Hinges FBB179 4 ½" x 4 ½" US26D 1 Each Mortise Dormitory Lockset 45H-7-TA-14H 626 1 Each Closer EHD9000 SPA90 689 1 Each Door Viewer #626 (mount at +60")Chrome 1 Each Kickplate 8" x 2" LDW x .050 US32D 1 Each Wall Stop #403 US32D 1 Set Perimeter Gaskets

HARDWARE SET 2

1½ Pairs Hinges FBB179 4 ½" x 4 ½" US26D 1 Each Cylindrical Privacy 9K3-0-L-14C-S3 626 1 Each Wall Stop #403 US32D

HARDWARE SET 3

2 Each Continuous Hinges KDFM HD1 1 Each Keyed Mullion KR822 x MCS822 Kit 695 1 Each Exit Device 2402 x 2002C 613 1 Each Exit Device 2403 x 2003C (RHRA) 613 2 Each Cylinders 12E72 RP3 613 2 Each Closers EHD9000 SDST90 x NFHD90 695 x BSHD90 x DP90 1 Each Mullion Gasket 5110BL 120" 1 Set Weatherstrip By Door Supplier 1 Each Threshold By Door Supplier

HARDWARE SET 4

2 Each Continuous Hinge KDFM HD1 1 Each Keyed Mullion KR822 x MCS822 Kit 695 1 Each Exit Device 2402 x 2002C 613 1 Each Exit Device 2403 x 2003C (RHRA) 613 2 Each Cylinders 12E72 RP3 613 2 Each Closers EHD9000 DST90 x NFHD90 695 x BSHD90 x DP90

HARDWARE SET 5

6 Each Hinges FBB179 4 1/2 x 4 1/2 US10B 1 Each Mortise Storeroom Lockset 45H-7-D-14H 613 2 Each Flush Bolts #555 US10B 1 Each Closer EHD9000 SDST90 695 1 Each Overhead Stop #9 with Hold-Open 613 2 Each Armor Plates 36" x 2" LDW x .050 US10B 1 Each Rain Drip 346D 1 Each Astragal 355DS 1 Each Threshold 2005AT 1 Set Perimeter Gaskets US10B

HARDWARE SET 6

1½ Pairs Hinges FBB179 4 ½" x 4 ½" US26D 1 Each Mortise Privacy 45H-0-L-14H VIT 626 1 Each Closer EHD9000 SPA90 689 1 Each Kick Plate 8" x 2" LDW x .050 US32D 1 Each Wall Stop #403 US32D 1 Set Perimeter Gaskets

HARDWARE SET 7

1½ Pairs Hinges FBB179 4 ½" x 4 ½" US26D 1 Each Mortise Classroom Lockset 45H-7-R-14H 626

SECTION 08 71 00 Page 10

Revised 21 Aug 24

SturdevantG Line

SturdevantG Line

SturdevantG Line

SturdevantG Line

1 Each Closer EHD9000 SPA90 689 1 Each Armor Plate 30" x 2" LDW x .050 US32D 1 Each Kick Plate (124A, 146) 8" x 2" LDW x .050 US32D 1 Each Wall Stop #403 US32D 1 Set Perimeter Gaskets

HARDWARE SET 7A

1½ Pairs Hinges FBB179 4 ½" x 4 ½" US26D 1 Each Mortise Classroom Lockset 45H-7-R-14H 626 1 Each Closer EHD9000 SPA90 689 1 Each Kick Plate 8" x 2" LDW x .050 US32D 1 Each Armor Plate (128) 30" x 2" LDW x .050 US32D 1 Each Overhead Stop #10 US32D 1 Set Perimeter Gaskets

HARDWARE SET 8

1½ Pairs Hinges FBB179 4 ½" x 4 ½" US26D 1 Each Mortise Storeroom Lockset 45H-7-D-14H 626 1 Each Closer EHD9000 SPA90 689 1 Each Armor Plate 16" x 2" LDW x .050 US32D 1 Each Overhead Stop #10 US32D 1 Set Perimeter Gaskets

HARDWARE SET 9

1 Pairs Hinges FBB179 4 ½" x 4 ½" US26D 1 Each Mortise Storeroom Lockset 45H-7-D-14H 626 1 Each Wall Stop #403 US32D

HARDWARE SET 9A

3 Each Hinges FBB179 4 ½" x 4 ½" US26D 1 Each Exit Device FL2103 x 4903D 630 1 Each Cylinder 12E72 RP3 626 1 Each Closer EHD9000 DS90 689 1 Each Kick Plate 8" x 2" LDW x .050 US32D 1 Each Perimeter Gaskets

HARDWARE SET 9B

3 Each Hinges FBB179 4 ½" x 4 ½" US26D 1 Each Mortise Storeroom 45H-7-D-14H 626 1 Each Closer EHD9000 DS90 689 1 Each Kick Plate 8" x 2" LDW x .050 US32D 1 Each Perimeter Gaskets

HARDWARE SET 10

3 Each Hinges FBB179 4 ½" x 4 ½" US26D 1 Each Mortise Storeroom 45H-7-D-14H 626 1 Each Closer EHD9000 SPA90 689 1 Each Kick Plate 8" x 2" LDW x .050 US32D 1 Each Wall Stop #403 US32D 1 Each Perimeter Gaskets

HARDWARE SET 11

1 Each Knox Box Dark Bronze

HARDWARE SET 12

1 Each Continuous Hinge KDFM HD1 1 Each Exit Device 2403 x 2003C 613 1 Each Cylinder 12E72 RP3 613 1 Each Closer EHD9000 SDST90 x NFHD90 695

SECTION 08 71 00 Page 11

Revised 21 Aug 24

SturdevantG Line

SturdevantG Line

SturdevantG Line

SturdevantG Line

SturdevantG Line

SturdevantG Line x BSHD90 x DP90 1 Set Weatherstrip By Door Supplier 1 Each Threshold By Door Supplier

HARDWARE SET 13

1½ Pairs Hinges FBB179 4 ½" x 4 ½" US26D 1 Each Mortise Passage Lockset 45H-O-N-14H 626 1 Each Closer EHD9000 SPA90 689 1 Each Kick Plate 8" x 2" LDW x .050 US32D 1 Each Wall Stop #403 US32D 1 Set Perimeter Gaskets

HARDWARE SET 14

1½ Pairs Hinges FBB179 4 ½" x 4 ½" US26D 1 Each Mortise Passage Lockset 45H-O-N-14H 626 1 Each Closer EHD9000 SPA90 689 1 Each Kick Plate 8" x 2" LDW x .050 US32D 1 Each Floor Stop 441 US26D 1 Set Perimeter Gaskets

HARDWARE SET 15

1½ Pairs Hinges FBB179 4 ½" x 4 ½" US26D 1 Each Mortise Storeroom Lockset 45H-7-D-14H 626 1 Each Closer EHD9000 DST90 689 1 Each Kick Plate 8" x 2" LDW x .050 US32D 1 Set Perimeter Gaskets

HARDWARE SET 16

1 Each Exit Device 2403 x 2003C 613 1 Each Cylinder 12E72 RP3 613 1 Each Closer EHD9000 SDST90 695 1 Each Kick Plate 8" x 2" LDW x .050 US10B 1 Each Rain Drip 346D 1 Each Threshold 2005AT 1 Set Perimeter Gaskets US32D Hinges are existing to remain.

HARDWARE SET 17

1½ Pairs Hinges FBB179 4 ½" x 4 ½" NRP US10B 1 Each Mortise Storeroom Lockset 45H-7-D-14H 613 1 Each Closer EHD9000 SDST90 695 1 Each Kick Plate 8" x 2" LDW x .050 US10B 1 Each Rain Drip 346D 1 Each Threshold 2005AT 1 Set Perimeter Gaskets US32D

-- End of Section --

SECTION 08 71 00 Page 12

Revised 21 Aug 24

SturdevantG Line

SturdevantG Line

SturdevantG Line

SturdevantG Line

SturdevantG Line