ESBD_433095_1751482960572_SOL_EXH_F.12_405-25R0014809_Door Hardware.pdf

DPS Facilities Bureau

Spec Rev. 06-2016

1 08 71 00 Page

SECTION 08 71 00 – DOOR HARDWARE

PART 1 – GENERAL

1.1 SECTION INCLUDES

A. Finish hardware for doors as specified and as listed in "Hardware Groups" and required by actual conditions.

1. Include screws, special screws, bolts, special bolts, expansion shields, and other devices for proper application of hardware.

1.2 STANDARDS

A. References specified in this section subject to compliance as directed:

1. NFPA-80-1999 - Standard for Fire Doors and Windows

2. NFPA-101-2003 - Life Safety Code

3. IBC 2006 – International Building Code

4. ADA - The Americans with Disabilities Act - Title III-Public Accommodations

5. ANSI-A117.1-American National Standards Institute - Accessible and Usable Bldgs and Facilities

6. ANSI-A156.5-American National Standards Institute - Auxiliary Locks and Associated Products

7. UFAS - Uniform Federal Accessibility Standards

8. UL - Underwriter's Laboratories, including UL-10B and UL-10C for Positive Pressure

9. WHI - Warnock Hersey International Division of Inchcape Testing Services

10. State and local codes including authority having jurisdiction

11. Applicable FEMA codes.

1. 3 GENERAL REQUIREMENTS

A. Provide items, articles, materials, operations and methods listed, mentioned or scheduled herein or on drawings, in quantities as required to complete project. Provide hardware that functions properly. Prior to furnishing hardware, advise Architect of items that will not operate properly, are improper for conditions, or will not remain permanently anchored.

1.4 QUALITY ASSURANCE

A. Manufacturer: Obtain each type of hardware (ie. latch and locksets, hinges, closers) from single manufacturer, although several may be indicated as offering products complying with requirements.

B. Regulatory Label Requirements: Provide nationally recognized testing agency label or stamp on hardware for labeled openings. Where UL requirements conflict with drawings or specifications, hardware conforming to UL requirements shall be provided. Conflicts and proposed substitutions shall be clearly indicated in hardware schedule.

1.5 DELIVERY, STORAGE AND HANDLING

A. Deliver hardware to jobsite in manufacturer's original packaging, marked to correspond with approved hardware schedule. Do not deliver hardware until suitable locked storage space is available. Check hardware against reviewed hardware schedule. Store hardware to protect against loss, theft or damage.

2 08 71 00 Page

1.6 WARRANTY

A. Guarantee workmanship and material provided against defective manufacture. Repair or replace defective workmanship and material appearing within period of one year after

B. Substantial Completion.

1. Provide ten year factory warranty on door closer body against defects in material and workmanship from date of occupancy of Project.

C. Replace shortages and incorrect items with correct material at no additional cost to Owner.

D. At completion of project, qualified factory representative shall inspect closer installations. After this inspection, letter shall be sent to Architect reporting on conditions, verifying that closers have been properly installed and adjusted.

PART 2 – PRODUCTS

2.1 BUTTS AND HINGES

A. Acceptable Manufacturers and Types:

Type McKinney Hager Stanley Type 1 T4A3795 BB1262 FBB268 Type 2 TA2714 BB1279 FBB179 Type 3 TA2314 BB1191 FBB191 Type 4 T4A3786 BB1168 FBB168

B. Application:

1. Exterior in swinging doors and vestibule doors Type 4

2. Interior doors with closers Type 2 or 4

3. Interior doors over 36 inches wide Type 4

4. Interior doors 36 inches or less without closer Type 2

5. Provide NRP (non-removable pins) at out-swinging lockable doors.

C. Size:

1. 2-1/4 inch Doors 5 inch by 5 inch

2. 1-3/4 inch Doors 4-1/2 inch by 4-1/2 inch

3. 1-3/8 inch Doors 3-1/3 inch by 3-1/2 inch

D. Quantity:

1. 2 - hinges per leaf for openings through 60 inches high.

2. 1 - additional hinge per leaf for each additional 30 inches in height or fraction thereof.

3. 4 - Dutch doors up to 90 inches in height.

4. Drill 5/32 inch hole and use No. 12, 1-1/4 inch steel threaded to the head wood screws for hinges on wood doors.

5. Hinges not clarified in Hardware Sets shall adhere to above requirements.

2.2 CONTINUOUS GEARED HINGES

A. Acceptable manufacturers:

3 08 71 00 Page

McKinney Markar Pemko

MCK-12HD N/A FM83SLFHD

MCK-25HD FM4011 FM83HD

B. Provide one of the above two models of continuous hinges as appropriate for the type, inset, and thickness of door where specified. Coordinate hinge types with the door supplier.

2.3 FLOOR CLOSERS & PIVOTS

A. Acceptable Manufacturers and Types of Concealed Floor Closers:

1. Rixson 27 / 51 Series or equal

2.4 LOCKSETS – MORTISE

A. Acceptable Manufacturer and Series:

1. Sargent 8200 Series x LNMI or equal.

B. Cylinders: Factory-registered extension of Sargent Keso system or equal.

C. Backsets: 2-3/4 inches.

2.5 EXIT DEVICES

A. Acceptable Manufacturers:

1. Sargent 80 Series.

B. Cylinders: Factory-registered extension of Sargent Keso system – no substitution.

C. Provide exit device series and functions as specified in Hardware Groups. Sargent product numbers are referenced in the Hardware Groups.

D. All exit devices shall be UL listed for panic. Exit devices for labeled doors shall be UL listed as "Fire Exit

Hardware".

E. Where lever trim is specified, provide lever design to match lockset levers.

F. Provide cylinders for exit devices with locking trim and cylinder dogging.

G. Provide cylinder dogging feature for non-rated exit devices.

H. Provide keyed removable mullions, as specified in the Hardware Groups.

2.6 KEYING

A. All cylinders to be interchangeable core, keyed to factory-registered extension of Sargent Keso Grand Master Key System or equal.

B. Provide 6 master keys for each master key set. Provide 3 change keys for each lock. Stamp keys "DO

NOT DUPLICATE."

C. Cylinders shall be construction keyed.

4 08 71 00 Page

2.7 DOOR TRIM

1. McKinney

2. Trimco

3. Hiawatha

B. Push Plates:

1. Where width of door stile prevents use of 6 inch wide plate, provide push plate one inch less than width of stile but not less than 4 inches wide.

C. Pulls:

1. Where required, mount back to back with push bars.

D. Kick Plates and Armor Plates: Minimum of 0.050 inch thick, beveled 4 edges.

1. At single doors provide width 1-1/2 inch less than door width on stop side and one inch less than door width on face side.

2. At pairs of doors provide width one inch less than door width on both sides.

3. Height of 8 inches, unless otherwise indicated.

E. Edge Guards: Minimum .050" thick, stainless steel,

1. McKinney EG02 (mortised) or EG06 (surface applied) x 42 inches high as noted in Hardware Groups.

2.8 DOOR CLOSERS

A. Acceptable Manufacturers and Types of Exposed Closers:

1. Sargent 1431 Series.

2. Norton 7500 / 8501 Series.

3. Corbin Russwin DC8000 / DC3000 Series.

B. Provide non-sized closers, adjustable to meet maximum opening force requirements of ADA.

C. Provide drop plates, brackets, or adapters for arms as required to suit details.

D. Mount closers on room side of corridor doors and inside of exterior doors.

E. Provide back-check for closers.

F. Provide hold-open arms where necessary.

G. Provide closers for doors as noted in Hardware Groups and, in addition, provide closers for labeled doors whether or not specifically noted in group.

H. Provide closers meeting the requirements of UBC 7-2, 1997 and UL 10C positive pressure tests.

I. Provide TB with all door closers.

2.9 OVERHEAD STOPS

5 08 71 00 Page

A. Acceptable Manufacturers

1. Rixson.

2. Norton.

3. Sargent.

B. Provide 10- Series overhead stops for doors equipped with regular arm surface type closer that swing more than 140 degrees before striking wall, and for doors that open against equipment, casework, sidelights, other objects that would make wall stops inappropriate.

2.10 WALL STOPS AND HOLDERS

McKinney Trimco Quality

WS01 1270WXCP W307RP

B. Provide WS01 Series wall stop as applicable, for each door leaf except where other wall stops are specified in Hardware Groups, or where conditions require the use of an overhead stop.

C. Floor or base stops shall be used only where definitely specified or absolutely unavoidable.

2.11 THRESHOLDS

Pemko McKinney Reese

171A MCK171A S205A

B. Where thresholds are specified in hardware groups, provide MCK171A thresholds unless detailed otherwise.

C. Provide accessories, shims and fasteners. Where thresholds occur at openings with one or more mullions, they shall be cut for the mullions and extended continuously for the entire opening.

2.12 WEATHERSTRIPPING

A. Acceptable Manufacturers and Product:

Sweeps 315CN MCK315CN 323A Jambs 316AV MCK316AV DS75A Door top drips 346C MCK346C R201A

B. Where weather-stripping is specified in hardware groups, provide 316AV unless detailed otherwise.

C. Provide self-tapping fasteners for weather-stripping being applied to hollow metal frames.

D. Where sweeps are specified in hardware groups, provide 315CN unless detailed otherwise.

E. Where rain drips are specified in hardware groups, provide 346C x full frame width, unless detailed

6 08 71 00 Page

2.13 GASKETING

McKinney Pemko Reese

MCKS88 S88 F-897B

B. Refer to drawings for special details. Provide accessories, shims and fasteners.

C. Where smoke gasket is specified in hardware groups, provide S88, unless detailed otherwise.

D. Provide gaskets for 20-minute doors and doors designated for smoke and draft control.

E. Where frame applied intumescent seals are required by the manufacturer, provide gaskets that comply with UBC 7-2, 1997 and UL 10C positive pressure tests.

2.14 SOUND GASKETING

Automatic Door Bottoms 4301CRL MCK4301CRL 330C Jambs 379CR MCK379CR 33C

B. Where gasket-ing is specified in hardware groups, provide 4301CRL and 379CR unless detailed

C. Provide self-tapping fasteners being applied to hollow metal doors and frames.

D. Cutting or notching of sound gasket for stop mounted hardware shall not be permitted.

2.15 FASTENERS

A. Including, but not limited to, wood or machine screws, bolts, bolts, nuts, anchors, etc. of proper type, material, and finish required for installation of hardware.

B. Use Phillips head for exposed screws. Do not use aluminum screws to attach hardware.

C. Provide self-tapping (TEC) screws for attachment of sweeps and stop-applied weather-stripping only.

2.16 TYPICAL FINISHES AND MATERIALS

A. Finishes, unless otherwise specified:

1. Butts: Interior Doors and in swinging Exterior Doors US26D (BHMA 652) on Steel

2. Continuous Hinges:

US28 (BHMA 628) on Aluminum

3. Locks and Latches:

US26D (BHMA 626) on Stainless Steel

7 08 71 00 Page

4. Push Plates, Pulls and Push Bars:

US32D (BHMA 630) on Stainless Steel

5. Kick Plates, Armor Plates, and Edge Guards:

US32D (BHMA 630) on Stainless Steel

6. Overhead Stops and Holders:

US26D (BHMA 626) on Stainless Steel

7. Closers: Surface mounted.

Sprayed Aluminum Lacquer.

8. Latch Protectors:

US32D (BHMA 630) on Stainless Steel

PART 3 – EXECUTION

3.1 EXAMINATION

A. Examine doors, frames, and related items for conditions that would prevent the proper application of finish hardware. Do not proceed until defects are corrected.

3.2 INSTALLATION

A. Install finish hardware in accordance with reviewed hardware schedule and manufacturer's printed instructions. Pre-fit hardware before finish is applied, remove and reinstall after finish is completed. Install hardware so that parts operate smoothly, close tightly and do not rattle.

B. Installation of hardware shall comply with NFPA 80 and NFPA 101 requirements.

C. Set units level, plumb and true to line and location. Adjust and reinforce attachment to substrate as necessary for proper installation and operation.

D. Drill and countersink units which are not factory-prepared for anchorage fasteners. Space fasteners and anchors in accordance with industry standards.

E. Set thresholds for exterior doors in full bed of butyl-rubber or polyisobutylene mastic sealant, forming tight seal between threshold and surface to which set. Securely and permanently anchor thresholds, using countersunk non-ferrous screws to match color of thresholds (stainless steel screws at aluminum thresholds).

F. Lead Protection: Lead wrap hardware penetrating lead-lined doors. Levers and roses to be lead lined.

Apply kick and armor plates with 3M adhesive #1357, as recommended by 3M Co., on lead-lined doors.

3.3 FIELD QUALITY CONTROL

A. After installation has been completed, provide services of qualified hardware consultant to check Project to determine proper application of finish hardware according to schedule.

B. Also check operation and adjustment of hardware items.

C. Adjust door control devices to compensate for final operation of heating and ventilating equipment.

3.4 ADJUSTING AND CLEANING

8 08 71 00 Page

A. At final completion, hardware shall be left clean and free from disfigurement. Make final adjustment to door closers and other items of hardware. Where hardware is found defective repair or replace or otherwise correct as directed.

B. Adjust door closers to meet opening force requirements of Uniform Federal Accessibility Standards.

C. Final Adjustment: Wherever hardware installation is made more than one month prior to acceptance or occupancy of space or area, return to work during week prior to acceptance or occupancy, and make final check and adjustment of hardware items in such space or area. Clean operating items as necessary to restore proper function and finish of hardware and doors.

D. Instruct Owner's personnel in proper adjustment and maintenance of door hardware and hardware finishes.

E. Clean adjacent surfaces soiled by hardware installation.

3.5 PROTECTION

A. Provide for proper protection of items of hardware until Owner accepts Project as complete.

3.6 HARDWARE GROUPS

A. The following schedule of hardware groups shall be considered a guide only, and the supplier is cautioned to refer to general conditions, special conditions, and the preamble to this section. It shall be the hardware supplier's responsibility to furnish all hardware required to meet codes regardless of schedule. Quantities are listed as a guide only. It is the responsibility of the supplier to furnish the correct quantity of hardware.

3.7 HARDWARE SCHEDULE

Abbreviation Manufacturer Catalog Information PEM Pemko http://www.pemko.com/ SGT Sargent http://sargentlock.com/ RIX Rixson http://www.rixson.com/

A. DL Entrance Door from Lobby

1 ea Floor Closer SC PH 5102N 626 RIX 1 ea Exit Device 82-16-AD8410 F 630 SGT 2 ea Intermediate Pivot M19 626 RIX 1 ea Dormitory Lockset 82-8245 LNMI 626 SGT 1 ea Overhead Stop 1- Series (concealed) 630 RIX 1 ea Door Bottom 315CN 628 PEM 1 ea Threshold 1 ea Perimeter Gasket By Frame & Door Manufacturer

END OF SECTION

9 08 71 00 Page