D6_MET_3_BINDER.pdf

NOAA • NOS • CO-OPS SHEET NO. : PAGE:

MET 3, ASSEMBLY

MET 3

CS-01 1/4

COVER SHEET

REVISIONS

REV DATE DRAWN BY APPROVED BY DESCRIPTION

- 04/25 CCE - FINAL

DRAWING INDEX

SHEET SHEET NO. TITLE

1 CS-01 COVER SHEET

2 AS-01 HINGE PLATE TOP

3 AS-02 ANCHORS

4 G-01 ITEM LIST

GENERAL NOTES

1. THE PURPOSE OF THIS DRAWING IS TO ADDRESS MET MAST BOLT PATTERN ISSUE WITH

COMPONENT 'SHAKESPEARE LIGHT POLE HINGED BASE PLATE'.

2. LINK TO VIEW 3D MODEL https://a360.co/3XnsFDA

3. BASED ON THE CURRENT DESIGN CRITERIA, THE ASSEMBLY SHALL BE DESIGNED TO

SURVIVE 180 MPH WIND SPEED WHEN USED WITH THE MET MAST SHOWN AND A

SHAKESPEARE LIGHT POLE DOUBLE ANEMOMETER MASTHEAD 'GOAL POST'.

4. ALL FASTENERS ARE TO BE SS 316, AND CONFORM TO ASTM F593/F594 UNLESS

OTHERWISE STATED.

5. THIS ASSEMBLY APPROX WEIGHT IS: 39 LBS + 114 LBS FOR THE 25' POLE.

6. ALL FASTENERS ARE TO BE INSTALLED WITH MARINE GRADE ANTI-SEIZE UNLESS

OTHERWISE STATED.

7. ALL DIMENSIONS ARE IN INCHES AND FEET UNLESS OTHERWISE STATED.

8. ABBREVIATIONS USED IN THIS DRAWING ARE AS FOLLOWS:

(N) = NEW (E) = EXISTING SH = SHEET GEN = GENERAL

TYP = TYPICAL EA = EACH ABV = ABOVE STND = STATION DATUM

PL = PLACES GFE = GOVERNMENT FURNISHED EQUIPMENT

CFE = CONTRACTOR FURNISHED EQUIPMENT

9. POC: (240) 343-6605, NOAA/CO-OPS/DDET, SILVER SPRING, MD

ISO OVERVIEW

MET HINGE PLATE ASSEMBLY

SEE SH AS-01 - AS-02 FOR DETAILS

SEE GENERAL NOTES 1-9

MET 3

AS-01 2/4

HINGE PLATE TOP

DO NOT SCALE DRAWING

DRAWING SIZE ANSI A

SHEET NOTES

1. FASTENERS AND HELI-COILS TO BE INSTALLED WITH

BLUE LOC-TITE.

2. DO NOT OVERTIGHTEN LOCK NUT, SHOULDER SCREW

(ITEM 7) SHOULD BE FREE FLOATING.

TOP VIEW

MET 3 HINGE PLATE

SEE SH AS-02 FOR DETAILS

SEE SHEET NOTES 1-2

(4 PLACES, SEE SH NOTE 1)

(4 PLACES)

(2 PLACES)

(2 PLACES, SEE SH NOTE 2)

(2 PLACES)

(7 PLACES)

(7 PLACES)

(7 PLACES)

(4 PLACES)

(4 PLACES)

(4 PLACES)

(4 PLACES)

(4 PLACES)

18(7 PLACES)

(AS NEEDED, 2 PLACES)

18(4 PLACES)

(7 PLACES)

(7 PLACES)

(7 PLACES)

(7 PLACES)

OR

OR

OR

OR21

2019(SEE SH NOTE 1) OR (SEE SH

NOTE 1)

19 (AS NEEDED, SEE SH NOTE 1)

18 (2 PLACES)

MET 3

AS-02 3/4

ANCHORS

DO NOT SCALE DRAWING

DRAWING SIZE ANSI A

ISOMETRIC VIEW

MET 3 HINGE PLATE

SEE SHEET NOTES 1-2

(SEE SH NOTES 1-2, 8 PL)

SHEET NOTES

1. THIS ASSEMBLY IS DESIGNED FOR 180 MPH WINDS AND TO BE ANCHORED WITH

5/8-11UNC ANCHORS, SEE INSTALLATION DRAWING FOR DETAILS. MINIMUM

EMBEDMENT SHALL BE 6-1/2" WITH A MINIMUM EDGE TO HOLE DISTANCE OF 8-1/2" AND

A MINIMUM CONCRETE THICKNESS OF 12". ADDITIONALLY A MINIMUM HOLE TO HOLE

DISTANCE OF 8" IS REQUIRED. IF THESE CONDITIONS CANNOT BE MET CONSULT WITH

DDET PRIOR TO INSTALL. NOTE THAT THE MET 3, BOTTOM PLATE AND MET 3, TOP

PLATE DRAWINGS MUST BE SPECIFICED FOR 5/8-11 FASTENERS WITH THE FABRICATOR.

2. IF THE WIND SPEED IS <160MPH THEN THIS ASSEMBLY CAN BE ANCHORED WITH

1/2-13UNC ANCHORS, SEE INSTALLATION DRAWING FOR DETAILS. MINIMUM

EMBEDMENT SHALL BE 6" WITH A MINIMUM EDGE TO HOLE DISTANCE OF 8" AND A

MINIMUM CONCRETE THICKNESS OF 12". ADDITIONALLY A MINIMUM HOLE TO HOLE

DISTANCE OF 7-1/4" IS REQUIRED. IF THESE CONDITIONS CANNOT BE MET CONSULT

WITH DDET PRIOR TO INSTALL. ADDITIONALLY THE TOP PLATE FASTENERS CAN BE

SWAPPED TO 1/2-13UNC, SEE MET 3, BOTTOM PLATE AND MET 3, TOP PLATE DRAWINGS

FOR HOLE CALLOUTS TO SPECIFY TO THE FABRICATOR.

MET 3

G-01 4/4

ITEM LIST

ITEM LIST

ITEM QTY DESCRIPTION REMARKS

1 1 MET 3, BOTTOM PLATE SEE DRAWING 'MET 3, BOTTOM PLATE' FOR DETAILS,

SPECIFY FASTENER SIZES

2 2 MET 3, BOTTOM PLATE HINGE SEE DRAWING 'MET 3, BOTTOM PLATE HINGE' FOR

DETAILS

3 1 MET 3, TOP PLATE SEE DRAWING 'MET 3, TOP PLATE' FOR DETAILS,

SPECIFY FASTENER SIZES

4 1 MET MAST SHAKESPEARE MODEL NO: AX25 OR AH25

5 4 1/2-13UNC X 1-3/4 LG, FULLY THREADED HEX HD SCREW,

SS316 CAN BE SUBSTITUTED WITH MONEL

6 4 1/2 WASHER, SS316 -

7 2 Ø3/8 SHOULDER X 5 LG SHOULDER, 5/16-18UNC THREAD

SOCKET HD SHOULDER SCREW, SS316

MCMASTER-CARR PART NO: 8077A573 OR

EQUIVALENT

8 2 5/16-18UNC NYLON LOCK NUT, SS316 -

9 7 5/8-11UNC X 1-1/2 LG, FULLY THREADED HEX HD SCREW,

SS316 CAN BE SUBSTITUTED WITH MONEL

10 7 5/8 WASHER, SS316 -

11 7 5/8 LOCK WASHER, SS316 -

12 4 1-8UNC X 3 LG, FULLY THREADED HEX HD SCREW, SS316 -

13 4 1 USS WASHER, SS316 MCMASTER-CARR PART NO: 93852A139 OR

EQUIVALENT

14 4 1 WASHER, SS316 -

15 4 1 LOCK WASHER, SS316 -

16 4 1-8UNC HEX NUT, SS316 -

17 2 3/8 X 0.03THK, SHOULDER SCREW SHIM, SS316 MCMASTER-CARR PART NO: 90792A436 OR 90792A336

OR EQUIVALENT

18 - MARINE GRADE ANTI-SEIZE LOCTITE PART NO: LB 8023

19 11 1/2-13 X 3/4 LG, HELICOIL, NITRONIC 60 SS MCMASTER-CARR PART NO: 96246A817 OR

EQUIVALENT

20 7 5/8-11 X 15/16 LG, HELICOIL, NITRONIC 60 SS OLANDER PART NO: 1185-10EN938 OR EQUIVALENT, NEEDS TO BE CUT TO LENGTH BEFORE INSTALL

21 7 1/2-13UNC X 1-1/2 LG, FULLY THREADED HEX HD SCREW,

SS316 CAN BE SUBSTITUTED WITH MONEL

22 7 1/2 LOCK WASHER, SS316 -

MET 3, TOP PLATE

MET 3

CS-01 1/5

COVER SHEET

REVISIONS

REV DATE DRAWN BY APPROVED BY DESCRIPTION

- 03/25 CCE - FINAL

DRAWING INDEX

SHEET SHEET NO. TITLE

1 CS-01 COVER SHEET

2 S-01 HINGE TOP AND CUT OUTS

3 S-02 BOLT HOLES

4 S-03 HINGE HOLE

5 G-01 ITEM LIST

GENERAL NOTES

1. THIS DRAWING SUPPLEMENTS THE 'MET 3, TOP PLATE.STEP' FILE, WHICH CONTAINS ALL

DIMENSIONS NOT CALLED OUT IN THIS DRAWING AND SHALL BE USED FOR FABRICATION.

2. LINK TO VIEW 3D MODEL https://a360.co/3CulFwE

3. THIS COMPONENT IS PART OF AN ASSEMBLY, SEE DRAWING 'MET 3, ASSEMBLY' FOR

DETAILS.

4. THE GENERAL TOLERANCE FOR THE COMPONENT IS ±0.01, ±0.5°; EXCEPT FOR

NON-REFERENCE DIMENSIONS CALLED OUT IN THIS DRAWING, THEN SEE TOLERANCE

BLOCK ON THAT SHEET.

5. THIS COMPONENT APPROX WEIGHT IS: 10 LBS.

6. ALL MATERIAL IS 6061-T6 AL, UNLESS OTHERWISE STATED.

7. ALL MACHINED SURFACES FINISH TO BE 125RMS.

8. REMOVE ALL BURRS, BREAK ALL SHARP EDGES AND CORNERS.

9. ALL DIMENSIONS ARE IN INCHES AND FEET UNLESS OTHERWISE STATED.

10. ABBREVIATIONS USED IN THIS DRAWING ARE AS FOLLOWS:

(N) = NEW (E) = EXISTING SH = SHEET GEN = GENERAL

TYP = TYPICAL EA = EACH ABV = ABOVE PL = PLACES

REF = REFERENCE

11.POC: (240) 533-0494, NOAA, SILVER SPRING, MD

ISO OVERVIEW

MET 3, TOP PLATE

SEE SH S-01 - S-03 FOR DETAILS

SEE GENERAL NOTES 1-11

MET 3

S-01 2/5

HINGE TOP AND CUT OUTS

UNLESS OTHERWISE SPECIFIED:

DRAWINGS ARE IN INCHES

TOLERANCES ARE:

FRACTIONS DECIMALS ANGLES

± 1/16 ± .X ± 0.1 ± 0.5°

± .XX ± 0.01

± .XXX ± 0.005

DO NOT SCALE DRAWING

DRAWING SIZE ANSI ASHEET NOTES

1. HARD ANODIZE PER MIL-A-8625F:

TYPE III CLASS 2

0.002" THICK ± 20%

COLOR: BLACK

SEAL: HOT NICKLE ACETATE SOLUTION

2. ALL DIMENSIONS APPLY BEFORE ANODIZING PROCESS

TOP VIEW

MET 3, TOP PLATE

SEE SHEET NOTES 1-2

16.00

4.826±.010

.45+.01

-.00 (3 PL)

R.75 (2 PL)

R.75

(10 PL)

R1.00 (5 PL)

R.5 (4 PL)

.5 (2 PL)

7.6

1.0 (2 PL)

6.5

6.5

4.52

FOR MATERIAL SPEC SEE ITEM M1

15.500

(2 PL)

(16.55

REF)

14.5

15.0

1.95

(2 PL)

5.587

R.275 (12 PL) 1.24+.00

-.01 (4 PL) 1.257+.010

-.000 (2 PL)

MET 3

S-02 3/5

BOLT HOLES

UNLESS OTHERWISE SPECIFIED:

DRAWINGS ARE IN INCHES

TOLERANCES ARE:

FRACTIONS DECIMALS ANGLES

± 1/16 ± .X ± 0.1 ± 0.5°

± .XX ± 0.01

± .XXX ± 0.005

DO NOT SCALE DRAWING

DRAWING SIZE ANSI A

TOP VIEW

MET 3, TOP PLATE

14.00

.9504.587

.25

7.00

9.15

13.46

12.00

2.00

8.132±.010

8.132±.010

3.664±.100

3.934±.100

Ø1.063 (4 PL)

Ø.688

(7 PL, SEE SH NOTE 1)

SHEET NOTE

1. IF REQUESTED DRILL THESE HOLES FOR Ø.563

MET 3

S-03 4/5

HINGE HOLE

UNLESS OTHERWISE SPECIFIED:

DRAWINGS ARE IN INCHES

TOLERANCES ARE:

FRACTIONS DECIMALS ANGLES

± 1/16 ± .X ± 0.1 ± 0.5°

± .XX ± 0.01

± .XXX ± 0.005

DO NOT SCALE DRAWING

DRAWING SIZE ANSI A

RIGHT VIEW

MET 3, TOP PLATE

4X Ø.397±.005 A

B

Ø0.005 A B .600 (4 PL)

.550 (4 PL)

1.0+.1

-.0 (2 PL)R.45+.10

-.00 (4 PL)

.015 R MAX,

SHARP CORNER NON-CRITICAL

(TYP)

R.275±.010 (4 PL) .50

MET 3

G-01 5/5

ITEM LIST

ITEM LIST

ITEM QTY DESCRIPTION REMARKS

M1 - PLATE, 6061-T6 AL -

1 - MET 3, TOP PLATE SEE SH S-01 - S-03 FOR DETAILS

MET 3, BOTTOM PLATE

MET 3

CS-01 1/5

COVER SHEET

REVISIONS

REV DATE DRAWN BY APPROVED BY DESCRIPTION

- 03/25 CCE - FINAL

DRAWING INDEX

SHEET SHEET NO. TITLE

1 CS-01 COVER SHEET

2 S-01 ANCHORS

3 S-02 BOLTS

4 S-03 PROFILE

5 G-01 ITEM LIST

ISO OVERVIEW

MET 3, BOTTOM PLATE

SEE SH S-01 - S-03 FOR DETAILS

SEE GENERAL NOTES 1-11

GENERAL NOTES

1. THIS DRAWING SUPPLEMENTS THE 'MET 3, BOTTOM PLATE.STEP' FILE, WHICH CONTAINS

ALL DIMENSIONS NOT CALLED OUT IN THIS DRAWING AND SHALL BE USED FOR

FABRICATION.

2. LINK TO VIEW 3D MODEL https://a360.co/3FlQWTH

3. THIS COMPONENT IS PART OF AN ASSEMBLY, SEE DRAWING 'MET 3, ASSEMBLY' FOR

DETAILS.

4. THE GENERAL TOLERANCE FOR THE COMPONENT IS ±0.01, ±0.5°; EXCEPT FOR

NON-REFERENCE DIMENSIONS CALLED OUT IN THIS DRAWING, THEN SEE TOLERANCE

BLOCK ON THAT SHEET.

5. THIS COMPONENT APPROX WEIGHT IS: 16 LBS.

6. ALL MATERIAL IS 6061-T6 AL, UNLESS OTHERWISE STATED.

7. ALL MACHINED SURFACES FINISH TO BE 125RMS.

8. REMOVE ALL BURRS, BREAK ALL SHARP EDGES AND CORNERS.

9. ALL DIMENSIONS ARE IN INCHES AND FEET UNLESS OTHERWISE STATED.

10. ABBREVIATIONS USED IN THIS DRAWING ARE AS FOLLOWS:

(N) = NEW (E) = EXISTING SH = SHEET GEN = GENERAL

TYP = TYPICAL EA = EACH ABV = ABOVE PL = PLACES

REF = REFERENCE

11.POC: (240) 533-0494, NOAA, SILVER SPRING, MD

MET 3

S-01 2/5

ANCHORS

UNLESS OTHERWISE SPECIFIED:

DRAWINGS ARE IN INCHES

TOLERANCES ARE:

FRACTIONS DECIMALS ANGLES

± 1/16 ± .X ± 0.1 ± 0.5°

± .XX ± 0.01

± .XXX ± 0.005

DO NOT SCALE DRAWING

DRAWING SIZE ANSI A

SHEET NOTES

1. HARD ANODIZE PER MIL-A-8625F:

TYPE III CLASS 2

0.002" THICK ± 20%

COLOR: BLACK

SEAL: HOT NICKLE ACETATE SOLUTION

2. ALL DIMENSIONS APPLY BEFORE ANODIZING PROCESS

3. PRIOR TO ANODIZING PLUG ALL THREADED HOLES

1.00 7.50

15.00

1.00

7.50

17.0019.0

17.0

5.0 (TYP)

5.0

(TYP)

R1.00 (4 PL)

R1.0 (TYP)

8.0

(2 PL)

1.0 (TYP)

1.0 (TYP)

Ø.750 (4 PL)

.33 (4 PL)

.66 (4 PL)

Ø.660 (8 PL)Ø.750 (4 PL)

45.0° (4 PL)

FOR MATERIAL SPEC SEE ITEM M1

TOP VIEW

MET 3, BOTTOM PLATE

SEE SHEET NOTES 1-3

MET 3

S-02 3/5

BOLTS

UNLESS OTHERWISE SPECIFIED:

DRAWINGS ARE IN INCHES

TOLERANCES ARE:

FRACTIONS DECIMALS ANGLES

± 1/16 ± .X ± 0.1 ± 0.5°

± .XX ± 0.01

± .XXX ± 0.005

DO NOT SCALE DRAWING

DRAWING SIZE ANSI A

.25

7.00

9.15

13.46

2.00

12.00

14.00

15.15

15.50

3.00

3.098±.0101.7371.737 4.3304X Ø.4255 .750

1/2-13 UNC - 2B

SEE SH NOTE 2

7X Ø.5365 .750

5/8-11 UNC - 2B

SEE SH NOTES 2 & 3

TOP VIEW

MET 3, BOTTOM PLATE

SEE SHEET NOTE 1

SHEET NOTES

1. PRIOR TO ANODIZING PLUG ALL THREADED HOLES

2. IF REQUESTED TAP THESE HOLES FOR 1/2-13 HELICOILS

3. IF REQUESTED TAP THESE HOLES FOR 5/8-11 HELICOILS

MET 3

S-03 4/5

PROFILE

UNLESS OTHERWISE SPECIFIED:

DRAWINGS ARE IN INCHES

TOLERANCES ARE:

FRACTIONS DECIMALS ANGLES

± 1/16 ± .X ± 0.1 ± 0.5°

± .XX ± 0.01

± .XXX ± 0.005

DO NOT SCALE DRAWING

DRAWING SIZE ANSI A

(.75 REF, AS SUPPLIED)

RIGHT VIEW

MET 3

G-01 5/5

ITEM LIST

ITEM LIST

ITEM QTY DESCRIPTION REMARKS

M1 - 0.75 THK, PLATE, 6061-T6 AL MUST MEET ASTM B209

1 - MET 3, BOTTOM PLATE SEE SH S-01 - S-03 FOR DETAILS

MET 3, BOTTOM PLATE HINGE

MET 3

CS-01 1/3

COVER SHEET

REVISIONS

REV DATE DRAWN BY APPROVED BY DESCRIPTION

- 03/25 CCE - FINAL

DRAWING INDEX

SHEET SHEET NO. TITLE

1 CS-01 COVER SHEET

2 S-01 FABRICATION

3 G-01 ITEM LIST

GENERAL NOTES

1. THIS DRAWING SUPPLEMENTS THE 'MET 3, BOTTOM PLATE HINGE.STEP' FILE, WHICH

CONTAINS ALL DIMENSIONS NOT CALLED OUT IN THIS DRAWING AND SHALL BE USED FOR

FABRICATION.

2. LINK TO VIEW 3D MODEL https://a360.co/3EaHCRN

3. THIS COMPONENT IS PART OF AN ASSEMBLY, SEE DRAWING 'MET 3, ASSEMBLY' FOR

DETAILS.

4. THE GENERAL TOLERANCE FOR THE COMPONENT IS ±0.01, ±0.5°; EXCEPT FOR

NON-REFERENCE DIMENSIONS CALLED OUT IN THIS DRAWING, THEN SEE TOLERANCE

BLOCK ON THAT SHEET.

5. THIS COMPONENT APPROX WEIGHT IS: 0.8 LBS.

6. ALL MATERIAL IS 6061-T6 AL, UNLESS OTHERWISE STATED.

7. ALL MACHINED SURFACES FINISH TO BE 125RMS.

8. REMOVE ALL BURRS, BREAK ALL SHARP EDGES AND CORNERS.

9. ALL DIMENSIONS ARE IN INCHES AND FEET UNLESS OTHERWISE STATED.

10. ABBREVIATIONS USED IN THIS DRAWING ARE AS FOLLOWS:

(N) = NEW (E) = EXISTING SH = SHEET GEN = GENERAL

TYP = TYPICAL EA = EACH ABV = ABOVE PL = PLACES

REF = REFERENCE

11.POC: (240) 533-0494, NOAA, SILVER SPRING, MD

ISO OVERVIEW

MET 3, BOTTOM PLATE HINGE

SEE SH S-01 FOR DETAILS

SEE GENERAL NOTES 1-11

MET 3

S-01 2/3

FABRICATION

UNLESS OTHERWISE SPECIFIED:

DRAWINGS ARE IN INCHES

TOLERANCES ARE:

FRACTIONS DECIMALS ANGLES

± 1/16 ± .X ± 0.1 ± 0.5°

± .XX ± 0.01

± .XXX ± 0.005

DO NOT SCALE DRAWING

DRAWING SIZE ANSI ASHEET NOTES

1. HARD ANODIZE PER MIL-A-8625F:

TYPE III CLASS 2

0.002" THICK ± 20%

COLOR: BLACK

SEAL: HOT NICKLE ACETATE SOLUTION

2. ALL DIMENSIONS APPLY BEFORE ANODIZING PROCESS

TOP VIEW

MET 3, BOTTOM PLATE HINGE

SEE SHEET NOTES 1-2

RIGHT VIEW

MET 3, BOTTOM PLATE HINGE

SEE SHEET NOTES 1-2

2.88

(3.737 REF) (1.0 REF,

AS SUPPLIED)

.850

1.737 .550

2.300

1.257+.010 -.000

1.000

1.24+.00

-.01 (2 PL)

1.56

45° X 0.3 (2 PL)

R.1 (4 PL)

11.31°+1.00°

-.00° (2 PL)

R.275±.010

(2 PL)

Ø.531 (2 PL)

.50

A

2X Ø.397±.005 Ø0.005 A B

FOR MATERIAL SPEC SEE ITEM M1

B

MET 3

G-01 3/3

ITEM LIST

ITEM LIST

ITEM QTY DESCRIPTION REMARKS

M1 - 1.0 THK, PLATE, 6061-T6 AL MUST MEET ASTM B209

1 - MET 3, BOTTOM PLATE HINGE SEE SH S-01 FOR DETAILS