D4_DMES_SDME_SOLAR_RACK_ASSEMBLY_-_BINDER.pdf
PDF 522 KB Posted
- Attached to
- PLATFORM FABRICATION SERVICES FOR NOAA Federal contract opportunity
- Solicitation number
- 1305M226Q0094
About this file
This document is a comprehensive set of technical drawings and specifications for a DMES/SDME Solar Rack Assembly, 45-degree configuration, produced by NOAA/NOS/CO-OPS. The assembly is designed to support an effective projected area of 86.16 x 27.48 inches angled at 45 degrees, with wind resistance capability up to 180 MPH at exposure category D when mounted 20 feet above the water surface. The complete assembly weighs approximately 100 pounds and must be mounted directly above the DMES or SDME to prevent support pipe failure.
The assembly comprises nine primary components: four fiberglass arms (upper right, lower right, upper left, and lower left), two aluminum arm spans (right and left), two aluminum tie rods (upper and lower), and fiberglass bracing. The frame assembly accommodates either DMES or SDME equipment through dual mounting hole patterns. The panel assembly supports 40-watt solar panels with provisions for both AOB (All-On-Board) and POB (Part-On-Board) bolt patterns. All fasteners are specified as stainless steel 316 conforming to ASTM F593/F594, installed with anti-seize compound. The item list includes 24 distinct components encompassing structural elements, fasteners (3/8-inch and 5/16-inch hardware), solar panels (Ameresco BSP40-12 or equivalent), and clamps (SnapNrack mid and adjustable end clamps). The drawings reference a 3D model accessible via a provided link and include detailed fabrication specifications with dimensional tolerances and material specifications for manufacturing.
View the file
Other files for this federal contract opportunity
| File | Type | Posted |
|---|---|---|
| D7_STANDARD_BUBBLER_ORIFICE__REV_A.pdf | ||
| Contractor_Past_Performance_Reference_Sheet.pdf | ||
| D6_MET_3_BINDER.pdf | ||
| D2_DMES_60X60X15__REV_D.pdf | ||
| D8_SADDLE_48_BINDER.pdf | ||
| D9_SHAKESPEARE_LIGHT_POLE_DOUBLE_ANEMOMETER_MASTHEAD__REV_C.pdf | ||
| Sol_1305M226Q0094.pdf | ||
| D1_8775870_Bob_Hall_Pier_7_5__PLATFORM_v15.pdf | ||
| D3_DMES_60X60X15_ASSEMBLY__REV_D.pdf | ||
| D5_11_Inch_Fixed_Arm_-_Straight_Flanges_v5.pdf | ||
| D10_GEODETIC_LEVELLING_COLLAR_FOR_MICROWAVE_WATER_LEVEL_SENSOR__REV_D.pdf |
Show all 11
On GovTribe
Work with this file on GovTribe
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
DRAWING INDEX
SHEET DWG NO TITLE
1 CS-01 COVER SHEET
2 AS-01 FRAME ASSEMBLY
3 AS-02 PANEL ASSEMBLY
4 G-01 ITEM LIST
REVISION DESCRIPTION
REV DESCRIPTION
DESIGN BY DDET 03/23
DRAWN BY CCE 03/23
APPROVED BY --- MM/YY
REVISION BY --- MM/YY NOAA / NOS / CO-OPS
REVISION
PROJECT STATUS
DMES_SDME SOLAR RACK ASSEMBLY, 45
Components
STATION STRUCTURAL COMPONENTS
A
PRODUCTION CS-01 1/4
COVER SHEET
GENERAL NOTES
1. THIS DRAWING SUPPLEMENTS THE 'DMES_SDME SOLAR RACK ASSEMBLY, 45, REV A.STEP'
FILE.
2. LINK TO VIEW 3D MODEL https://a360.co/3j4M7TR
3. THIS ASSEMBLY APPROX WEIGHT IS: 100 LBS.
4. THIS ASSEMBLY IS DESIGNED TO SUPPORT AN EFFECTIVE PROJECTED AREA OF
86.16X27.48 ANGLED AT 45° UP TO 180MPH AT EXPOSURE CATEGORY D, MOUNTED 20'
ABOVE THE WATER SURFACE. THE ASSEMBLY MUST BE MOUNTED DIRECTLY ABOVE THE
DMES OR SDME OTHERWISE THE SUPPORT PIPES MAY FAIL. IF THESE CONDITIONS
CANNOT BE MET CONSULT WITH DDET PRIOR TO INSTALL.
5. ALL DIMENSIONS ARE IN INCHES AND FEET UNLESS OTHERWISE STATED.
6. ALL FASTENERS ARE TO BE SS 316, AND CONFORM TO ASTM F593/F594 UNLESS
OTHERWISE STATED.
7. ALL FASTENERS ARE TO BE INSTALLED WITH ANTI-SEIZE UNLESS OTHERWISE STATED.
8. ABBREVIATIONS USED IN THIS DRAWING ARE AS FOLLOWS:
(N) = NEW (E) = EXISTING SH = SHEET GEN = GENERAL
TYP = TYPICAL EA = EACH ABV = ABOVE PL = PLACES
REF = REFERENCE
9. POC: (240) 533-0494, NOAA, SILVER SPRING, MD
ISO OVERVIEW
SOLAR RACK ASSEMBLY
SEE SH AS-01 - AS-02 FOR DETAILS
SEE GENERAL NOTES 1-9
DO NOT SCALE DRAWING
DRAWING SIZE ANSI A NOAA / NOS / CO-OPS
REVISION
PROJECT STATUS
DMES_SDME SOLAR RACK ASSEMBLY, 45
Components
STATION STRUCTURAL COMPONENTS
A
PRODUCTION AS-01 2/4
FRAME ASSEMBLY
73 4 10
(8 PLACES)
(2, 8 PLACES)
(2, 8 PLACES)
(12 PLACES)
(2, 12 PLACES)
(12 PLACES)
(12 PLACES)
(4 PLACES)
(4 PLACES)
(2, 4 PLACES)
(4 PLACES)
(4 PLACES)
(2, 4 PLACES)
(4 PLACES)
(4 PLACES)
ISO VIEW
RACK FRAME ASSEMBLY
NOTE: THE INNER HOLE IS FOR DMES
THE OUTER HOLE IS FOR SDME
DO NOT SCALE DRAWING
DRAWING SIZE ANSI A NOAA / NOS / CO-OPS
REVISION
PROJECT STATUS
DMES_SDME SOLAR RACK ASSEMBLY, 45
Components
STATION STRUCTURAL COMPONENTS
A
PRODUCTION AS-02 3/4
PANEL ASSEMBLY
1617 18
(2, 6 PLACES)
(6 PLACES)
(6 PLACES) 22
(6 PLACES)
(6 PLACES)
(4 PLACES)
(4 PLACES)
(4 PLACES)
(4 PLACES)
(2, 4 PLACES)
(TYP)
NOTE: THERE ARE TWO BOLT PATTERNS,
FOR AOB AND POB PATTERN SOLAR PANELS;
THE ONE SHOWN BEING USED
IS FOR AOB PATTERN SOLAR PANELS
23OR 23OR
TOP VIEW
SOLAR PANEL ASSEMBLY
SEE SH NOTE 1
SHEET NOTE
1. TORQUE MID AND END CLAMPS (ITEMS 17 & 18) TO 10FT-LBS.
ITEM LIST
ITEM QTY DESCRIPTION REMARKS
1 1 UPPER RIGHT ARM, 45 BUILD TO PRINT, SEE DRAWING 'UPPER RIGHT ARM, 45' FOR DETAILS
2 1 LOWER RIGHT ARM, 45 BUILD TO PRINT, SEE DRAWING 'LOWER RIGHT ARM, 45' FOR DETAILS
3 1 UPPER LEFT ARM, 45 BUILD TO PRINT, SEE DRAWING 'UPPER LEFT ARM, 45' FOR DETAILS
4 1 LOWER LEFT ARM, 45 BUILD TO PRINT, SEE DRAWING 'LOWER LEFT ARM, 45' FOR DETAILS
5 1 RIGHT ARM SPAN BUILD TO PRINT, SEE DRAWING 'RIGHT ARM SPAN' FOR DETAILS
6 1 LEFT ARM SPAN BUILD TO PRINT, SEE DRAWING 'LEFT ARM SPAN' FOR DETAILS
7 1 UPPER TIE ROD BUILD TO PRINT, SEE DRAWING 'UPPER TIE ROD' FOR DETAILS
8 1 LOWER TIE ROD BUILD TO PRINT, SEE DRAWING 'LOWER TIE ROD' FOR DETAILS
9 2 BRACING BUILD TO PRINT, SEE DRAWING 'BRACING' FOR DETAILS
10 8 U-BOLT, 3/8-16UNC THREAD X 2 ID, SS316 -
11 40 3/8 WASHER, SS316 -
12 16 3/8-16UNC NYLON LOCKNUT, SS316 FASTENERS ARE TO BE INSTALLED WITH ANTI-SEIZE UNLESS OTHERWISE STATED
13 20 3/8-16UNC X 1-5/8 LG, PARTIALLY THREADED HEX HD SCREW, SS316 -
14 20 3/8 SPLIT WASHER, SS316 -
15 20 3/8-16UNC NUT, SS316 -
16 - 40W SOLAR PANEL AMERESCO PART NO: BSP40-12 OR BSP40J-40W, ACTUAL QUANTITY REQ'D SHALL BE
SPECIFIED ON INSTALLATION DRAWING
17 6 BONDING MID CLAMP-NOTE DO NOT USE MANUFACTURER
SUPPLIED FASTENERS SNAPNRACK PART NO: 242-02070
18 4 BONDING ADJUSTABLE END CLAMP TOP-NOTE THE END CLAMP
BASE IS NOT REQ'D FOR THIS ASSEMBLY SNAPNRACK PART NO: 242-02072
19 10 5/16-18UNC X 2-3/4 LG, PARTIALLY THREADED HEX HD SCREW,
SS316 FOR AOB PATTERN PANELS
20 20 5/16 WASHER, SS316 -
21 10 5/16 SPLIT WASHER, SS316 -
22 10 5/16-18UNC NUT, SS316 -
23 10 5/16-18UNC X 3-1/2 LG, PARTIALLY THREADED HEX HD SCREW,
SS316 FOR POB PATTERN PANELS
24 16 OVERSIZED 3/8 WASHER, 1.0 OD X 0.406 ID, SS316 MCMCASTER-CARR PART NO: 91525A329 OR EQUIVALENT
NOAA / NOS / CO-OPS
REVISION
PROJECT STATUS
DMES_SDME SOLAR RACK ASSEMBLY, 45
Components
STATION STRUCTURAL COMPONENTS
A
PRODUCTION G-01 4/4
1 CS-01 COVER SHEET
2 S-01 FABRICATION
3 G-01 ITEM LIST
REVISION DESCRIPTION
REV DESCRIPTION
DESIGN BY DDET 01/23
DRAWN BY CCE 01/23
APPROVED BY --- MM/YY
REVISION BY --- MM/YY NOAA / NOS / CO-OPS
REVISION
PROJECT STATUS
UPPER RIGHT ARM, 45
Components
STATION STRUCTURAL COMPONENTS
A
PRODUCTION CS-01 1/3
COVER SHEET
ISO OVERVIEW
UPPER RIGHT ARM
SEE SH S-01 FOR DETAILS
SEE GENERAL NOTES 1-11
GENERAL NOTES
1. THIS DRAWING SUPPLEMENTS THE 'UPPER RIGHT ARM, 45.STEP' FILE, WHICH CONTAINS
ALL DIMENSIONS NOT CALLED OUT IN THIS DRAWING AND SHALL BE USED FOR
FABRICATION.
2. THIS COMPONENT IS PART OF AN ASSEMBLY, SEE DRAWING 'DMES_SDME SOLAR RACK
ASSEMBLY, 45' FOR DETAILS.
3. THE GENERAL TOLERANCE FOR THE COMPONENT IS ±0.01, ±1.0°; EXCEPT FOR
NON-REFERENCE DIMENSIONS CALLED OUT IN THIS DRAWING, THEN SEE TOLERANCE
BLOCK ON THAT SHEET.
4. THIS PART APPROX WEIGHT IS: 2.9 LBS.
5. ALL MATERIAL IS FIBERGLASS, UNLESS OTHERWISE STATED.
6. ALL FIBERGLASS CUT ENDS TO BE SEALED WITH MARINE EPOXY TO PREVENT WATER
INTRUSION.
7. ALL MACHINED SURFACES FINISH TO BE 125RMS.
8. REMOVE ALL BURRS, BREAK ALL SHARP EDGES AND CORNERS.
9. ALL DIMENSIONS ARE IN INCHES AND FEET UNLESS OTHERWISE STATED.
10. ABBREVIATIONS USED IN THIS DRAWING ARE AS FOLLOWS:
(N) = NEW (E) = EXISTING SH = SHEET GEN = GENERAL
TYP = TYPICAL EA = EACH ABV = ABOVE PL = PLACES
REF = REFERENCE
11.POC: (240) 533-0494, NOAA, SILVER SPRING, MD
UNLESS OTHERWISE SPECIFIED DIMENSIONS
ARE IN INCHES TOLERANCES ARE:
FRACTIONS DECIMALS ANGLES
± 1/16 ± .X ± 0.1 ± 0.5°
± .XX ± 0.01
± .XXX ± 0.005
DO NOT SCALE DRAWING
DRAWING SIZE ANSI A
NOAA / NOS / CO-OPS
REVISION
PROJECT STATUS
UPPER RIGHT ARM, 45
Components
STATION STRUCTURAL COMPONENTS
A
PRODUCTION S-01 2/3
FABRICATION
135.0°
Ø2.00+.02
-.00 (TYP)
6.75
.750
6.500
.250 (TYP)
2.190 3.000Ø.438 (TYP)
7.071 2.442
3.00
6.00
45.0°
Ø.438 (TYP)
SHEET NOTES
1. ALL FIBERGLASS CUT ENDS TO BE SEALED WITH MARINE EPOXY TO PREVENT
WATER INTRUSION.
FRONT VIEW
UPPER RIGHT ARM
SEE SHEET NOTE 1
TOP VIEW
UPPER RIGHT ARM
SEE SHEET NOTE 1
FOR MATERIAL SPEC SEE ITEM M1
4.35 (TYP)
2.298+.000
-.020 (TYP)
M1 - 8 X 2-3/16 X 3/8, CHANNEL, FRP, VINYL ESTER RESIN -
1 - UPPER RIGHT ARM, 45 SEE SH S-01 FOR DETAILS
NOAA / NOS / CO-OPS
REVISION
PROJECT STATUS
UPPER RIGHT ARM, 45
Components
STATION STRUCTURAL COMPONENTS
A
PRODUCTION G-01 3/3
1 CS-01 COVER SHEET
2 S-01 FABRICATION
3 G-01 ITEM LIST
REVISION DESCRIPTION
REV DESCRIPTION
DESIGN BY DDET 01/23
DRAWN BY CCE 01/23
APPROVED BY --- MM/YY
REVISION BY --- MM/YY NOAA / NOS / CO-OPS
REVISION
PROJECT STATUS
LOWER RIGHT ARM, 45
Components
STATION STRUCTURAL COMPONENTS
A
PRODUCTION CS-01 1/3
COVER SHEET
GENERAL NOTES
1. THIS DRAWING SUPPLEMENTS THE 'LOWER RIGHT ARM, 45.STEP' FILE, WHICH CONTAINS
ALL DIMENSIONS NOT CALLED OUT IN THIS DRAWING AND SHALL BE USED FOR
FABRICATION.
2. THIS COMPONENT IS PART OF AN ASSEMBLY, SEE DRAWING 'DMES_SDME SOLAR RACK
ASSEMBLY, 45' FOR DETAILS.
3. THE GENERAL TOLERANCE FOR THE COMPONENT IS ±0.01, ±1.0°; EXCEPT FOR
NON-REFERENCE DIMENSIONS CALLED OUT IN THIS DRAWING, THEN SEE TOLERANCE
BLOCK ON THAT SHEET.
4. THIS PART APPROX WEIGHT IS: 5.7 LBS.
5. ALL MATERIAL IS FIBERGLASS, UNLESS OTHERWISE STATED.
6. ALL FIBERGLASS CUT ENDS TO BE SEALED WITH MARINE EPOXY TO PREVENT WATER
INTRUSION.
7. ALL MACHINED SURFACES FINISH TO BE 125RMS.
8. REMOVE ALL BURRS, BREAK ALL SHARP EDGES AND CORNERS.
9. ALL DIMENSIONS ARE IN INCHES AND FEET UNLESS OTHERWISE STATED.
10. ABBREVIATIONS USED IN THIS DRAWING ARE AS FOLLOWS:
(N) = NEW (E) = EXISTING SH = SHEET GEN = GENERAL
TYP = TYPICAL EA = EACH ABV = ABOVE PL = PLACES
REF = REFERENCE
11.POC: (240) 533-0494, NOAA, SILVER SPRING, MD
ISO OVERVIEW
LOWER RIGHT ARM
SEE SH S-01 FOR DETAILS
SEE GENERAL NOTES 1-11
FRACTIONS DECIMALS ANGLES
± 1/16 ± .X ± 0.1 ± 0.5°
± .XX ± 0.01
± .XXX ± 0.005
DO NOT SCALE DRAWING
DRAWING SIZE ANSI A
NOAA / NOS / CO-OPS
REVISION
PROJECT STATUS
LOWER RIGHT ARM, 45
Components
STATION STRUCTURAL COMPONENTS
A
PRODUCTION S-01 2/3
FABRICATION
FRONT VIEW
LOWER RIGHT ARM
SEE SHEET NOTE 1
SHEET NOTES
1. ALL FIBERGLASS CUT ENDS TO BE SEALED WITH MARINE EPOXY TO PREVENT
WATER INTRUSION.
24.826±.010
45.0° 135.0°
3.006.00
1.488
16.617
Ø.438 (TYP)
FOR MATERIAL SPEC SEE ITEM M1
.750
6.500
2.298+.000
-.020 (TYP)
3.000
.250 (TYP)
2.190
TOP VIEW
LOWER RIGHT ARM
SEE SHEET NOTE 1
4.35 (TYP)Ø2.00+.02
-.00 (TYP)
Ø.438 (TYP)
M1 - 8 X 2-3/16 X 3/8, CHANNEL, FRP, VINYL ESTER RESIN -
1 - LOWER RIGHT ARM, 45 SEE SH S-01 FOR DETAILS
NOAA / NOS / CO-OPS
REVISION
PROJECT STATUS
LOWER RIGHT ARM, 45
Components
STATION STRUCTURAL COMPONENTS
A
1 CS-01 COVER SHEET
2 S-01 FABRICATION
3 G-01 ITEM LIST
REVISION DESCRIPTION
REV DESCRIPTION
DESIGN BY DDET 01/23
DRAWN BY CCE 01/23
APPROVED BY --- MM/YY
REVISION BY --- MM/YY NOAA / NOS / CO-OPS
REVISION
PROJECT STATUS
UPPER LEFT ARM, 45
Components
STATION STRUCTURAL COMPONENTS
A
PRODUCTION CS-01 1/3
COVER SHEET
ISO OVERVIEW
UPPER LEFT ARM
SEE SH S-01 FOR DETAILS
SEE GENERAL NOTES 1-11
GENERAL NOTES
1. THIS DRAWING SUPPLEMENTS THE 'UPPER LEFT ARM, 45.STEP' FILE, WHICH CONTAINS
ALL DIMENSIONS NOT CALLED OUT IN THIS DRAWING AND SHALL BE USED FOR
FABRICATION.
2. THIS COMPONENT IS PART OF AN ASSEMBLY, SEE DRAWING 'DMES_SDME SOLAR RACK
ASSEMBLY, 45' FOR DETAILS.
3. THE GENERAL TOLERANCE FOR THE COMPONENT IS ±0.01, ±1.0°; EXCEPT FOR
NON-REFERENCE DIMENSIONS CALLED OUT IN THIS DRAWING, THEN SEE TOLERANCE
BLOCK ON THAT SHEET.
4. THIS PART APPROX WEIGHT IS: 2.9 LBS.
5. ALL MATERIAL IS FIBERGLASS, UNLESS OTHERWISE STATED.
6. ALL FIBERGLASS CUT ENDS TO BE SEALED WITH MARINE EPOXY TO PREVENT WATER
INTRUSION.
7. ALL MACHINED SURFACES FINISH TO BE 125RMS.
8. REMOVE ALL BURRS, BREAK ALL SHARP EDGES AND CORNERS.
9. ALL DIMENSIONS ARE IN INCHES AND FEET UNLESS OTHERWISE STATED.
10. ABBREVIATIONS USED IN THIS DRAWING ARE AS FOLLOWS:
(N) = NEW (E) = EXISTING SH = SHEET GEN = GENERAL
TYP = TYPICAL EA = EACH ABV = ABOVE PL = PLACES
FRACTIONS DECIMALS ANGLES
± 1/16 ± .X ± 0.1 ± 0.5°
± .XX ± 0.01
± .XXX ± 0.005
DO NOT SCALE DRAWING
DRAWING SIZE ANSI A
NOAA / NOS / CO-OPS
REVISION
PROJECT STATUS
UPPER LEFT ARM, 45
Components
STATION STRUCTURAL COMPONENTS
A
PRODUCTION S-01 2/3
FABRICATIONSHEET NOTES
1. ALL FIBERGLASS CUT ENDS TO BE SEALED WITH MARINE EPOXY TO PREVENT
WATER INTRUSION.
FRONT VIEW
UPPER LEFT ARM
SEE SHEET NOTE 1
45.0° 135.0°
6.75
Ø2.00+.02 -.00
TOP VIEW
UPPER LEFT ARM
SEE SHEET NOTE 1
3.00
6.00
Ø.438 (TYP)
FOR MATERIAL SPEC SEE ITEM M1
2.442
7.071
.750
6.500
3.000
.250 (TYP)
2.190Ø.438 (TYP)
4.35 (TYP)
2.298+.000
-.020 (TYP)
M1 - 8 X 2-3/16 X 3/8, CHANNEL, FRP, VINYL ESTER RESIN -
1 - UPPER LEFT ARM, 45 SEE SH S-01 FOR DETAILS
NOAA / NOS / CO-OPS
REVISION
PROJECT STATUS
UPPER LEFT ARM, 45
Components
STATION STRUCTURAL COMPONENTS
A
1 CS-01 COVER SHEET
2 S-01 FABRICATION
3 G-01 ITEM LIST
REVISION DESCRIPTION
REV DESCRIPTION
DESIGN BY DDET 01/23
DRAWN BY CCE 01/23
APPROVED BY --- MM/YY
REVISION BY --- MM/YY NOAA / NOS / CO-OPS
REVISION
PROJECT STATUS
LOWER LEFT ARM, 45
Components
STATION STRUCTURAL COMPONENTS
A
PRODUCTION CS-01 1/3
COVER SHEET
ISO OVERVIEW
LOWER LEFT ARM
SEE SH S-01 FOR DETAILS
SEE GENERAL NOTES 1-11
GENERAL NOTES
1. THIS DRAWING SUPPLEMENTS THE 'LOWER LEFT ARM, 45.STEP' FILE, WHICH CONTAINS
ALL DIMENSIONS NOT CALLED OUT IN THIS DRAWING AND SHALL BE USED FOR
FABRICATION.
2. THIS COMPONENT IS PART OF AN ASSEMBLY, SEE DRAWING 'DMES_SDME SOLAR RACK
ASSEMBLY, 45' FOR DETAILS.
3. THE GENERAL TOLERANCE FOR THE COMPONENT IS ±0.01, ±1.0°; EXCEPT FOR
NON-REFERENCE DIMENSIONS CALLED OUT IN THIS DRAWING, THEN SEE TOLERANCE
BLOCK ON THAT SHEET.
4. THIS PART APPROX WEIGHT IS: 5.7 LBS.
5. ALL MATERIAL IS FIBERGLASS, UNLESS OTHERWISE STATED.
6. ALL FIBERGLASS CUT ENDS TO BE SEALED WITH MARINE EPOXY TO PREVENT WATER
INTRUSION.
7. ALL MACHINED SURFACES FINISH TO BE 125RMS.
8. REMOVE ALL BURRS, BREAK ALL SHARP EDGES AND CORNERS.
9. ALL DIMENSIONS ARE IN INCHES AND FEET UNLESS OTHERWISE STATED.
10. ABBREVIATIONS USED IN THIS DRAWING ARE AS FOLLOWS:
(N) = NEW (E) = EXISTING SH = SHEET GEN = GENERAL
TYP = TYPICAL EA = EACH ABV = ABOVE PL = PLACES
FRACTIONS DECIMALS ANGLES
± 1/16 ± .X ± 0.1 ± 0.5°
± .XX ± 0.01
± .XXX ± 0.005
DO NOT SCALE DRAWING
DRAWING SIZE ANSI A
NOAA / NOS / CO-OPS
REVISION
PROJECT STATUS
LOWER LEFT ARM, 45
Components
STATION STRUCTURAL COMPONENTS
A
PRODUCTION S-01 2/3
FABRICATION
FRONT VIEW
LOWER LEFT ARM
SEE SHEET NOTE 1
TOP VIEW
LOWER LEFT ARM
SEE SHEET NOTE 1
45.0° 135.0°
3.00 6.00
Ø.438 (TYP)
FOR MATERIAL SPEC SEE ITEM M1
1.488
16.617
6.500
3.000
.250 (TYP)
2.190Ø.438 (TYP)
.750
24.826±.010
2.298+.000
-.020 (TYP)
4.35 (TYP)
Ø2.00+.02
-.00 (TYP)
M1 - 8 X 2-3/16 X 3/8, CHANNEL, FRP, VINYL ESTER RESIN -
1 - LOWER LEFT ARM, 45 SEE SH S-01 FOR DETAILS
NOAA / NOS / CO-OPS
REVISION
PROJECT STATUS
LOWER LEFT ARM, 45
Components
STATION STRUCTURAL COMPONENTS
A
1 CS-01 COVER SHEET
2 S-01 FABRICATION
3 G-01 ITEM LIST
REVISION DESCRIPTION
REV DESCRIPTION
DESIGN BY DDET 01/23
DRAWN BY CCE 01/23
APPROVED BY --- MM/YY
REVISION BY --- MM/YY NOAA / NOS / CO-OPS
REVISION
PROJECT STATUS
RIGHT ARM SPAN
Components
STATION STRUCTURAL COMPONENTS
A
PRODUCTION CS-01 1/3
COVER SHEET
GENERAL NOTES
1. THIS DRAWING SUPPLEMENTS THE 'RIGHT ARM SPAN.STEP' FILE, WHICH CONTAINS ALL
DIMENSIONS NOT CALLED OUT IN THIS DRAWING AND SHALL BE USED FOR FABRICATION.
2. THIS COMPONENT IS PART OF AN ASSEMBLY, SEE DRAWING 'DMES_SDME SOLAR RACK
ASSEMBLY, 45' FOR DETAILS.
3. THE GENERAL TOLERANCE FOR THE COMPONENT IS ±0.01, ±1.0°; EXCEPT FOR
NON-REFERENCE DIMENSIONS CALLED OUT IN THIS DRAWING, THEN SEE TOLERANCE
BLOCK ON THAT SHEET.
4. THIS PART APPROX WEIGHT IS: 5.9 LBS.
5. ALL MATERIAL IS 6061-T6 AL, UNLESS OTHERWISE STATED.
6. ALL MACHINED SURFACES FINISH TO BE 125RMS.
7. REMOVE ALL BURRS, BREAK ALL SHARP EDGES AND CORNERS.
8. ALL DIMENSIONS ARE IN INCHES AND FEET UNLESS OTHERWISE STATED.
9. ABBREVIATIONS USED IN THIS DRAWING ARE AS FOLLOWS:
(N) = NEW (E) = EXISTING SH = SHEET GEN = GENERAL
TYP = TYPICAL EA = EACH ABV = ABOVE PL = PLACES
REF = REFERENCE
10.POC: (240) 533-0494, NOAA, SILVER SPRING, MD
ISO OVERVIEW
RIGHT ARM SPAN
SEE GENERAL NOTES 1-10
FRACTIONS DECIMALS ANGLES
± 1/16 ± .X ± 0.1 ± 0.5°
± .XX ± 0.01
± .XXX ± 0.005
DO NOT SCALE DRAWING
DRAWING SIZE ANSI A
NOAA / NOS / CO-OPS
REVISION
PROJECT STATUS
RIGHT ARM SPAN
Components
STATION STRUCTURAL COMPONENTS
A
PRODUCTION S-01 2/3
FABRICATION
FRONT VIEW
RIGHT ARM SPAN 1
45° X 1.5 2.00
R.275Ø.438 (TYP)
3.000
6.000
3.000
6.000 3.50
17.00
1.500
29.7
1.500
23.5502.875±.010
TOP VIEW
RIGHT ARM SPAN
Ø.438 (TYP)
FOR MATERIAL SPEC SEE ITEM M1
.788±.010
M1 - 3 X 3 X 0.375, ANGLE, 6061-T6 AL -
1 - RIGHT ARM SPAN SEE SH S-01 FOR DETAILS
NOAA / NOS / CO-OPS
REVISION
PROJECT STATUS
RIGHT ARM SPAN
Components
STATION STRUCTURAL COMPONENTS
A
1 CS-01 COVER SHEET
2 S-01 FABRICATION
3 G-01 ITEM LIST
REVISION DESCRIPTION
REV DESCRIPTION
DESIGN BY DDET 01/23
DRAWN BY CCE 01/23
APPROVED BY --- MM/YY
REVISION BY --- MM/YY NOAA / NOS / CO-OPS
REVISION
PROJECT STATUS
LEFT ARM SPAN
Components
STATION STRUCTURAL COMPONENTS
A
PRODUCTION CS-01 1/3
COVER SHEET
ISO OVERVIEW
LEFT ARM SPAN
SEE SH S-01 FOR DETAILS
SEE GENERAL NOTES 1-10
GENERAL NOTES
1. THIS DRAWING SUPPLEMENTS THE 'LEFT ARM SPAN.STEP' FILE, WHICH CONTAINS ALL
DIMENSIONS NOT CALLED OUT IN THIS DRAWING AND SHALL BE USED FOR FABRICATION.
2. THIS COMPONENT IS PART OF AN ASSEMBLY, SEE DRAWING 'DMES_SDME SOLAR RACK
ASSEMBLY, 45' FOR DETAILS.
3. THE GENERAL TOLERANCE FOR THE COMPONENT IS ±0.01, ±1.0°; EXCEPT FOR
NON-REFERENCE DIMENSIONS CALLED OUT IN THIS DRAWING, THEN SEE TOLERANCE
BLOCK ON THAT SHEET.
4. THIS PART APPROX WEIGHT IS: 5.9 LBS.
5. ALL MATERIAL IS 6061-T6 AL, UNLESS OTHERWISE STATED.
6. ALL MACHINED SURFACES FINISH TO BE 125RMS.
7. REMOVE ALL BURRS, BREAK ALL SHARP EDGES AND CORNERS.
8. ALL DIMENSIONS ARE IN INCHES AND FEET UNLESS OTHERWISE STATED.
9. ABBREVIATIONS USED IN THIS DRAWING ARE AS FOLLOWS:
(N) = NEW (E) = EXISTING SH = SHEET GEN = GENERAL
TYP = TYPICAL EA = EACH ABV = ABOVE PL = PLACES
10.POC: (240) 533-0494, NOAA, SILVER SPRING, MD
FRACTIONS DECIMALS ANGLES
± 1/16 ± .X ± 0.1 ± 0.5°
± .XX ± 0.01
± .XXX ± 0.005
DO NOT SCALE DRAWING
DRAWING SIZE ANSI A
NOAA / NOS / CO-OPS
REVISION
PROJECT STATUS
LEFT ARM SPAN
Components
STATION STRUCTURAL COMPONENTS
A
PRODUCTION S-01 2/3
FABRICATION
FRONT VIEW
LEFT ARM SPAN
TOP VIEW
LEFT ARM SPAN
1.500
2.875±.010 23.550
Ø.438 (TYP)
45° X 1.5
FOR MATERIAL SPEC SEE ITEM M1
1.500
29.7
3.000
6.000
3.000
6.000 3.50
17.00
2.00
R.275Ø.438 (TYP)
.788±.010
M1 - 3 X 3 X 0.375, ANGLE, 6061-T6 AL -
1 - LEFT ARM SPAN SEE SH S-01 FOR DETAILS
NOAA / NOS / CO-OPS
REVISION
PROJECT STATUS
LEFT ARM SPAN
Components
STATION STRUCTURAL COMPONENTS
A
1 CS-01 COVER SHEET
2 S-01 FABRICATION
3 G-01 ITEM LIST
REVISION DESCRIPTION
REV DESCRIPTION
DESIGN BY DDET 01/23
DRAWN BY CCE 01/23
APPROVED BY --- MM/YY
REVISION BY --- MM/YY NOAA / NOS / CO-OPS
REVISION
PROJECT STATUS
UPPER TIE ROD
Components
STATION STRUCTURAL COMPONENTS
A
PRODUCTION CS-01 1/3
COVER SHEET
ISO OVERVIEW
UPPER TIE ROD
SEE SH S-01 FOR DETAILS
SEE GENERAL NOTES 1-10
GENERAL NOTES
1. THIS DRAWING SUPPLEMENTS THE 'UPPER TIE ROD.STEP' FILE, WHICH CONTAINS ALL
DIMENSIONS NOT CALLED OUT IN THIS DRAWING AND SHALL BE USED FOR FABRICATION.
2. THIS COMPONENT IS PART OF AN ASSEMBLY, SEE DRAWING 'DMES_SDME SOLAR RACK
ASSEMBLY, 45' FOR DETAILS.
3. THE GENERAL TOLERANCE FOR THE COMPONENT IS ±0.01, ±1.0°; EXCEPT FOR
NON-REFERENCE DIMENSIONS CALLED OUT IN THIS DRAWING, THEN SEE TOLERANCE
BLOCK ON THAT SHEET.
4. THIS PART APPROX WEIGHT IS: 21.9 LBS.
5. ALL MATERIAL IS 6061-T6 AL, UNLESS OTHERWISE STATED.
6. ALL MACHINED SURFACES FINISH TO BE 125RMS.
7. REMOVE ALL BURRS, BREAK ALL SHARP EDGES AND CORNERS.
8. ALL DIMENSIONS ARE IN INCHES AND FEET UNLESS OTHERWISE STATED.
9. ABBREVIATIONS USED IN THIS DRAWING ARE AS FOLLOWS:
(N) = NEW (E) = EXISTING SH = SHEET GEN = GENERAL
TYP = TYPICAL EA = EACH ABV = ABOVE PL = PLACES
10.POC: (240) 533-0494, NOAA, SILVER SPRING, MD
FRACTIONS DECIMALS ANGLES
± 1/16 ± .X ± 0.1 ± 0.5°
± .XX ± 0.01
± .XXX ± 0.005
DO NOT SCALE DRAWING
DRAWING SIZE ANSI A
NOAA / NOS / CO-OPS
REVISION
PROJECT STATUS
UPPER TIE ROD
Components
STATION STRUCTURAL COMPONENTS
A
PRODUCTION S-01 2/3
FABRICATION
FRONT VIEW
UPPER TIE ROD 1
(4.0 REF)
1.688±.010
2.688±.010
10.50010.50026.000 26.000
22.00021.850
21.75021.650
22.000 21.850
21.750 21.650 2.875±.010
90.0
Ø.438 (TYP)FOR MATERIAL SPEC SEE ITEM M1
1.2401.240
M1 - 4 X 3 X 0.375, ANGLE, 6061-T6 AL -
1 - UPPER TIE ROD SEE SH S-01 FOR DETAILS
NOAA / NOS / CO-OPS
REVISION
PROJECT STATUS
UPPER TIE ROD
Components
STATION STRUCTURAL COMPONENTS
A
1 CS-01 COVER SHEET
2 S-01 FABRICATION
3 G-01 ITEM LIST
REVISION DESCRIPTION
REV DESCRIPTION
DESIGN BY DDET 01/23
DRAWN BY CCE 01/23
APPROVED BY --- MM/YY
REVISION BY --- MM/YY NOAA / NOS / CO-OPS
REVISION
PROJECT STATUS
LOWER TIE ROD
Components
STATION STRUCTURAL COMPONENTS
A
PRODUCTION CS-01 1/3
COVER SHEET
GENERAL NOTES
1. THIS DRAWING SUPPLEMENTS THE 'LOWER TIE ROD.STEP' FILE, WHICH CONTAINS ALL
DIMENSIONS NOT CALLED OUT IN THIS DRAWING AND SHALL BE USED FOR FABRICATION.
2. THIS COMPONENT IS PART OF AN ASSEMBLY, SEE DRAWING 'DMES_SDME SOLAR RACK
ASSEMBLY, 45' FOR DETAILS.
3. THE GENERAL TOLERANCE FOR THE COMPONENT IS ±0.01, ±1.0°; EXCEPT FOR
NON-REFERENCE DIMENSIONS CALLED OUT IN THIS DRAWING, THEN SEE TOLERANCE
BLOCK ON THAT SHEET.
4. THIS PART APPROX WEIGHT IS: 20.8 LBS.
5. ALL MATERIAL IS 6061-T6 AL, UNLESS OTHERWISE STATED.
6. ALL MACHINED SURFACES FINISH TO BE 125RMS.
7. REMOVE ALL BURRS, BREAK ALL SHARP EDGES AND CORNERS.
8. ALL DIMENSIONS ARE IN INCHES AND FEET UNLESS OTHERWISE STATED.
9. ABBREVIATIONS USED IN THIS DRAWING ARE AS FOLLOWS:
(N) = NEW (E) = EXISTING SH = SHEET GEN = GENERAL
TYP = TYPICAL EA = EACH ABV = ABOVE PL = PLACES
REF = REFERENCE
10.POC: (240) 533-0494, NOAA, SILVER SPRING, MD
ISO OVERVIEW
LOWER TIE ROD
SEE GENERAL NOTES 1-10
FRACTIONS DECIMALS ANGLES
± 1/16 ± .X ± 0.1 ± 0.5°
± .XX ± 0.01
± .XXX ± 0.005
DO NOT SCALE DRAWING
DRAWING SIZE ANSI A
NOAA / NOS / CO-OPS
REVISION
PROJECT STATUS
LOWER TIE ROD
Components
STATION STRUCTURAL COMPONENTS
A
PRODUCTION S-01 2/3
FABRICATION
2.688±.010
1.688±.010
2.875±.010
90.0
18.700 18.700
21.750 21.750
22.000 22.000
21.65021.650
17.800 17.800
21.85021.850
.600Ø.250
Ø.438 (TYP)
8.50
30.30
8.50
30.30
A
4.75
1.60
FRONT VIEW
LOWER TIE ROD 1
DETAIL A
CUTOUT DETAIL (TYP)
R.275 (TYP)
(4.0 REF)
1.240 1.240
M1 - 4 X 3 X 0.375, ANGLE, 6061-T6 AL -
1 - LOWER TIE ROD SEE SH S-01 FOR DETAILS
NOAA / NOS / CO-OPS
REVISION
PROJECT STATUS
LOWER TIE ROD
Components
STATION STRUCTURAL COMPONENTS
A
1 CS-01 COVER SHEET
2 S-01 FABRICATION
3 G-01 ITEM LIST
REVISION DESCRIPTION
REV DESCRIPTION
DESIGN BY DDET 01/23
DRAWN BY CCE 01/23
APPROVED BY --- MM/YY
REVISION BY --- MM/YY NOAA / NOS / CO-OPS
REVISION
PROJECT STATUS
BRACING
Components
STATION STRUCTURAL COMPONENTS
A
PRODUCTION CS-01 1/3
COVER SHEET
GENERAL NOTES
1. THIS DRAWING SUPPLEMENTS THE 'BRACING.STEP' FILE, WHICH CONTAINS ALL
DIMENSIONS NOT CALLED OUT IN THIS DRAWING AND SHALL BE USED FOR FABRICATION.
2. THIS COMPONENT IS PART OF AN ASSEMBLY, SEE DRAWING 'DMES_SDME SOLAR RACK
ASSEMBLY, 45' FOR DETAILS.
3. THE GENERAL TOLERANCE FOR THE COMPONENT IS ±0.01, ±1.0°; EXCEPT FOR
NON-REFERENCE DIMENSIONS CALLED OUT IN THIS DRAWING, THEN SEE TOLERANCE
BLOCK ON THAT SHEET.
4. THIS PART APPROX WEIGHT IS: 3.6 LBS.
5. ALL MATERIAL IS FIBERGLASS, UNLESS OTHERWISE STATED.
6. ALL FIBERGLASS CUT ENDS TO BE SEALED WITH MARINE EPOXY TO PREVENT WATER
INTRUSION.
7. ALL MACHINED SURFACES FINISH TO BE 125RMS.
8. REMOVE ALL BURRS, BREAK ALL SHARP EDGES AND CORNERS.
9. ALL DIMENSIONS ARE IN INCHES AND FEET UNLESS OTHERWISE STATED.
10. ABBREVIATIONS USED IN THIS DRAWING ARE AS FOLLOWS:
(N) = NEW (E) = EXISTING SH = SHEET GEN = GENERAL
TYP = TYPICAL EA = EACH ABV = ABOVE PL = PLACES
REF = REFERENCE
11.POC: (240) 533-0494, NOAA, SILVER SPRING, MD
ISO OVERVIEW
BRACING
SEE GENERAL NOTES 1-11
FRACTIONS DECIMALS ANGLES
± 1/16 ± .X ± 0.1 ± 0.5°
± .XX ± 0.01
± .XXX ± 0.005
DO NOT SCALE DRAWING
DRAWING SIZE ANSI A
NOAA / NOS / CO-OPS
REVISION
PROJECT STATUS
BRACING
Components
STATION STRUCTURAL COMPONENTS
A
PRODUCTION S-01 2/3
FABRICATION
FRONT VIEW
BRACING
SEE SH NOTE 1
TOP VIEW
BRACING
SEE SH NOTE 1
45° X 2.0 (TYP)
1.3024.940
1.50
Ø.438 (TYP)
27.5
SHEET NOTES
1. ALL FIBERGLASS CUT ENDS TO BE SEALED WITH MARINE EPOXY TO PREVENT
WATER INTRUSION.
M1 - 3 X 3 X 0.375, ANGLE, FRP -
1 - BRACING SEE SH S-01 FOR DETAILS
NOAA / NOS / CO-OPS
REVISION
PROJECT STATUS
BRACING
Components
STATION STRUCTURAL COMPONENTS
A
File details come from the government source that posted it. Updated .