D5_11_Inch_Fixed_Arm_-_Straight_Flanges_v5.pdf
PDF 215 KB Posted
- Attached to
- PLATFORM FABRICATION SERVICES FOR NOAA Federal contract opportunity
- Solicitation number
- 1305M226Q0094
About this file
This is a technical drawing specification for a NOAA National Ocean Service Center for Operational Oceanographic Products and Services (CO-OPS) station structural component. The document details an 11-inch fixed arm with straight flanges designed for short arm mounting applications.
The bill of materials specifies four 6061 aluminum tubes measuring 2" x 2" x 1/4", two 6061 aluminum angles measuring 2" x 3" x 1/4", and three 6061 aluminum angles measuring 2" x 2" x 1/4". General manufacturing notes require all groove welds to achieve full joint penetration with a 0.12-inch root opening, all fillet welds to be a minimum of 1/4 inch unless otherwise specified, continuous welding throughout, and 4043 filler wire for all welds. Machined surfaces must finish to 125 RMS, with all welds ground flush to material on top. The drawing indicates standard tolerance specifications: fractions ±1/16 inch, decimals ±0.01 to ±0.06 inch depending on decimal places, and angles ±0.5 degrees. The component was finalized on March 18, 2026, and is designated as Sheet Number S-01, Page 1/1, with an ANSI A drawing size.
View the file
Other files for this federal contract opportunity
| File | Type | Posted |
|---|---|---|
| Sol_1305M226Q0094.pdf | ||
| D4_DMES_SDME_SOLAR_RACK_ASSEMBLY_-_BINDER.pdf | ||
| D1_8775870_Bob_Hall_Pier_7_5__PLATFORM_v15.pdf | ||
| Contractor_Past_Performance_Reference_Sheet.pdf | ||
| D6_MET_3_BINDER.pdf | ||
| D2_DMES_60X60X15__REV_D.pdf | ||
| D8_SADDLE_48_BINDER.pdf | ||
| D9_SHAKESPEARE_LIGHT_POLE_DOUBLE_ANEMOMETER_MASTHEAD__REV_C.pdf | ||
| D7_STANDARD_BUBBLER_ORIFICE__REV_A.pdf | ||
| D3_DMES_60X60X15_ASSEMBLY__REV_D.pdf | ||
| D10_GEODETIC_LEVELLING_COLLAR_FOR_MICROWAVE_WATER_LEVEL_SENSOR__REV_D.pdf |
Show all 11
On GovTribe
Work with this file on GovTribe
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
NOAA • NOS • CO-OPS SHEET NO. : PAGE:
STATION STRUCTURAL COMPONENTS
11" FIXED ARM-STRAIGHT FLANGES
S-01 1/1
SHORT ARM MOUNT
REVISIONS
REV DATE DRAWN BY APPROVED BY DESCRIPTION
- 3/18/26 MDM - FINAL
ISO OVERVIEW
DO NOT SCALE DRAWING
DRAWING SIZE ANSI A
UNLESS OTHERWISE SPECIFIED:
DRAWINGS ARE IN INCHES
TOLERANCES ARE:
FRACTIONS DECIMALS ANGLES
± 1/16 ± .X ± 0.1 ± 0.5°
± .XX ± 0.06
± .XXX ± 0.01
BILL OF MATERIALS
ITEM QTY DESCRIPTION
1 4 6061 ALUMINUM TUBE, 2" X 2" X 1/4"
2 2 6061 ALUMINUM ANGLE, 2" X 3" X 1/4"
3 3 6061 ALUMINUM ANGLE, 2" X 2" X 1/4"
A
DETAIL A
.870
6.000
Ø.44, THREE PLACES
9.00
1.38
45°
9.68
9.18
R1.00
10.42
Ø.56 SIX PLACES
1.38
BACKGOUGE,
TWO PLACES
BACKGOUGE,
FOUR PLACES
BACKGOUGE,
TWO PLACES
BACKGOUGE,
FOUR PLACES
12.31
BACKGOUGE,
TWO PLACES
3.466
1.125
GENERAL NOTES
1. ALL GROOVE WELDS SHALL BE FULL JOINT PENETRATION
2. ALL GROVE WELDS SHALL HAVE A 0.12" ROOT OPENING
3. ALL FILLET WELDS SHALL BE A MINIMUM OF 14" UNLESS OTHERWISE SPECIFIED.
4. ALL WELDS TO BE CONTINOUS UNLESS OTHERWISE SPECIFIED.
5. USE 4043 FILLER WIRE FOR ALL WELDS.
6. GRIND FLUSH TO MATERIAL ON TOP.
7. ALL MACHINED SURFACES FINISH TO BE 125 RMS
3.125
3.125
File details come from the government source that posted it. Updated .