D2_DMES_60X60X15__REV_D.pdf
PDF 407 KB Posted
- Attached to
- PLATFORM FABRICATION SERVICES FOR NOAA Federal contract opportunity
- Solicitation number
- 1305M226Q0094
About this file
This document is a technical drawing set for DMES (Data Management and Engineering System) Station Structural Components, specifically for a 60X60X15 enclosure frame assembly, Revision D, produced by NOAA/NOS/CO-OPS.
The drawing package comprises eight sheets detailing fabrication specifications for an aluminum frame structure and auxiliary components with a total approximate weight of 187 pounds. All materials are 6061-T6 aluminum except for stainless steel 316 flat bar components. The frame consists of welded aluminum angles and channels with the following key specifications: minimum 0.25-inch fillet welds using 4043 filler wire, full joint penetration groove welds, continuous welding throughout, and all machined surfaces finished to 125 RMS. The assembly includes a main DMES frame (sheets S-01 through S-03) featuring specific dimensional requirements including overall dimensions of 82.4 inches height by 70 inches width with slot and hole patterns for equipment mounting; three enclosure clamps (sheet S-04) with angular bends and specific hole patterns; one spacer component (sheet S-05) measuring 36 inches long with three 0.625-inch diameter holes; and two enclosure bolt-down bars (sheet S-06) measuring 58 inches in length. All dimensions are in inches and feet with specified tolerances. The bill of materials (sheet G-01) identifies seven material components including angles, channels, and flat bars in varying sizes. All holes and slots must be drilled after welding, with burrs removed and sharp edges broken per general fabrication notes. The point of contact is listed as (240) 533-0494, NOAA, Silver Spring, Maryland.
View the file
Other files for this federal contract opportunity
| File | Type | Posted |
|---|---|---|
| D7_STANDARD_BUBBLER_ORIFICE__REV_A.pdf | ||
| Contractor_Past_Performance_Reference_Sheet.pdf | ||
| D6_MET_3_BINDER.pdf | ||
| D8_SADDLE_48_BINDER.pdf | ||
| D9_SHAKESPEARE_LIGHT_POLE_DOUBLE_ANEMOMETER_MASTHEAD__REV_C.pdf | ||
| D3_DMES_60X60X15_ASSEMBLY__REV_D.pdf | ||
| D5_11_Inch_Fixed_Arm_-_Straight_Flanges_v5.pdf | ||
| D10_GEODETIC_LEVELLING_COLLAR_FOR_MICROWAVE_WATER_LEVEL_SENSOR__REV_D.pdf | ||
| Sol_1305M226Q0094.pdf | ||
| D4_DMES_SDME_SOLAR_RACK_ASSEMBLY_-_BINDER.pdf | ||
| D1_8775870_Bob_Hall_Pier_7_5__PLATFORM_v15.pdf |
Show all 11
On GovTribe
Work with this file on GovTribe
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
DRAWING INDEX
SHEET DWG NO TITLE
1 CS-01 COVER SHEET
2 S-01 FRAME
3 S-02 FRAME BASE BOTTOM
4 S-03 FRAME BASE TOP
5 S-04 ENCLOSURE CLAMP
6 S-05 SPACER
7 S-06 ENCLOSURE BOLT DOWN BAR
8 G-01 ITEM LIST
REVISION DESCRIPTION
REV DESCRIPTION
D DMES BASE WAS WIDENED AND FILLET WELD SIZE IN CORNER CHANGED DUE TO ISSUES WITH 60X60X15 APX ENCLOSURE NOT FITTING BETWEEN UPRGIHTS. A SPACER WAS ADDED TO PREVENT THE UPPER ENCLOSURE FRAME HORIZONTAL SUPPORT FROM BENDING DURING ASSEMBLY. MOUNTING HOLE PATTERN 1 WAS ELIMINATED FOR BEING UNNECESSARY.
DESIGN BY BLS 03/10
DRAWN BY BLS 06/14
APPROVED BY --- MM/YY
REVISION BY CCE 10/22 NOAA / NOS / CO-OPS
REVISION
PROJECT STATUS
DMES_60X60X15
Components
STATION STRUCTURAL COMPONENTS
D
PRODUCTION CS-01 1/8
COVER SHEET
GENERAL NOTES
1. THIS DRAWING SUPPLEMENTS THE 'DMES_60X60X15, REV D.STEP' FILE, WHICH CONTAINS
ALL DIMENSIONS NOT CALLED OUT IN THIS DRAWING AND SHALL BE USED FOR
FABRICATION.
2. THESE COMPONENTS ARE PART OF AN ASSEMBLY, SEE DRAWING 'DMES_60X60X15
ASSEMBLY, REV D' FOR DETAILS.
3. THESE COMPONENTS APPROX WEIGHT IS: 187 LBS.
4. ALL MATERIAL IS 6061-T6 AL, UNLESS OTHERWISE STATED.
5. ALL FILLET WELDS SHALL BE A MINIMUM OF 0.25" UNLESS OTHERWISE NOTED.
6. ALL GROOVE WELDS SHALL BE FULL JOINT PENETRATION.
7. ALL WELDS TO BE CONTINUOUS UNLESS OTHERWISE SPECIFIED.
8. USE 4043 FILLER WIRE FOR ALL WELDS.
9. GRIND FLUSH TO MATERIAL ON TOP.
10.GRIND FLUSH TO MATERIAL ON BOTTOM.
11. ALL MACHINED SURFACES FINISH TO BE 125RMS.
12.DRILL HOLES AND SLOTS AFTER WELDING THIS SECTION.
13.REMOVE ALL BURRS, BREAK ALL SHARP EDGES AND CORNERS.
14. ALL DIMENSIONS ARE IN INCHES AND FEET UNLESS OTHERWISE STATED.
15. ABBREVIATIONS USED IN THIS DRAWING ARE AS FOLLOWS:
(N) = NEW (E) = EXISTING SH = SHEET GEN = GENERAL
TYP = TYPICAL EA = EACH ABV = ABOVE PL = PLACES
REF = REFERENCE
16.POC: (240) 533-0494, NOAA, SILVER SPRING, MD
ISO OVERVIEW
DMES FRAME & AUXILLARY PARTS
SEE SH S-01 - S-03 FOR FRAME DETAILS
SEE SH S-04 - S-06 FOR AUXILLARY PARTS
SEE GENERAL NOTES 1-16
UNLESS OTHERWISE SPECIFIED DIMENSIONS
ARE IN INCHES TOLERANCES ARE:
FRACTIONS DECIMALS ANGLES
± 1/16 ± .X ± 0.1 ± 0.5°
± .XX ± 0.06
± .XXX ± 0.01
DO NOT SCALE DRAWING
DRAWING SIZE ANSI A
NOAA / NOS / CO-OPS
REVISION
PROJECT STATUS
DMES_60X60X15
Components
STATION STRUCTURAL COMPONENTS
D
PRODUCTION S-01 2/8
FRAME
82.4
70.00 (2 PLACES)
4.38 (2 PLACES)
21.0
74.0
Ø.625 (TYP)
B
.310
(TYP)
Ø.438 (TYP)
.84 2.50
C
C 17.25
18.0
DETAIL B (TYP)
THE SLOT DIMS SHOWN ARE FLIPPED FOR THE OPPOSITE SIDE
SEE GENERAL NOTES 4-5, 7-8, 11, 13-15
SECTION C-C (TYP)
THE LEG DIM SHOWN IS THE SAME FOR THE OPPOSITE SIDE
SEE GENERAL NOTES 4-5, 7-8, 10-11, 13-15
FRONT VIEW
DMES FRAME
SEE GENERAL NOTES 4, 13-15
FOR MATERIAL SPEC
SEE ITEM M1 (TYP) 1
FOR MATERIAL SPEC
SEE ITEM M2 (TYP)
FOR MATERIAL SPEC
SEE ITEM M3 (TYP)
FOR MATERIAL SPEC
SEE ITEM M4
.75
(TYP, SEE
GEN NOTE 10)
(TYP)
1/8
90.0° (TYP)
FOR MATERIAL SPEC
SEE ITEM M7
35.00
15.81 (TYP)
A
DETAIL A (TYP)
THE SLOT DIMS SHOWN ARE FLIPPED FOR THE OPPOSITE SIDE
SEE GENERAL NOTES 4-5, 7-8, 11, 13-15
.84 .310
(TYP)
2.50
1.75
Ø.438 (TYP)
FRACTIONS DECIMALS ANGLES
± 1/16 ± .X ± 0.1 ± 0.5°
± .XX ± 0.06
± .XXX ± 0.01
DO NOT SCALE DRAWING
DRAWING SIZE ANSI A
NOAA / NOS / CO-OPS
REVISION
PROJECT STATUS
DMES_60X60X15
Components
STATION STRUCTURAL COMPONENTS
D
PRODUCTION S-02 3/8
FRAME BASE BOTTOM
D D
65.75±.10
20.25±.10
1.375±.060
1.25
3.188±.060 (TYP)
13.938±.060 (TYP)
17.75
3.187±.060
(TYP)
59.188±.060
(TYP)
63.00
E
.625
Ø.875COPE AS
NEEDED
(2 PLACES)
SECTION D-D
DMES FRAME SLOT PATTERN
SEE GENERAL NOTES 4, 6-8, 10-15
RIGHT VIEW
DMES FRAME
SEE GENERAL NOTES 4-5, 7-8, 11, 13-15
DETAIL E (TYP)
DMES FRAME SLOT DETAIL
SEE GENERAL NOTE 12
1/8 60°
(TYP, SEE SH NOTE 10)
(TYP)
SEE GEN NOTE 12
FRACTIONS DECIMALS ANGLES
± 1/16 ± .X ± 0.1 ± 0.5°
± .XX ± 0.06
± .XXX ± 0.01
DO NOT SCALE DRAWING
DRAWING SIZE ANSI A
NOAA / NOS / CO-OPS
REVISION
PROJECT STATUS
DMES_60X60X15
Components
STATION STRUCTURAL COMPONENTS
D
PRODUCTION S-03 4/8
FRAME BASE TOP
F F 27.50
(TYP)
55.00
9.502.75
2.75
Ø.875 (TYP)
60.5
15.0
COPE AS NEEDED (2 PLACES)
RIGHT VIEW
DMES FRAME
SECTION F-F
DMES FRAME HOLE PATTERN
SEE GENERAL NOTES 4-8, 9, 11-15
1/8 60°
(TYP, SEE SH NOTE 9)
(TYP)
SEE GEN NOTE 12 (TYP)
FRACTIONS DECIMALS ANGLES
± 1/16 ± .X ± 0.1 ± 0.5°
± .XX ± 0.06
± .XXX ± 0.01
DO NOT SCALE DRAWING
DRAWING SIZE ANSI A
NOAA / NOS / CO-OPS
REVISION
PROJECT STATUS
DMES_60X60X15
Components
STATION STRUCTURAL COMPONENTS
D
PRODUCTION S-04 5/8
ENCLOSURE CLAMP
75.0°
100.0°
85.0° 2.46
3.05
5.41
1.92
1.10
3.00
(.25 REF, AS SUPPLIED)
RIGHT VIEW
ENCLOSURE CLAMP
SEE GENERAL NOTES 11-15
FRONT VIEW
ENCLOSURE CLAMP
SEE GENERAL NOTES 11-15
ISOMETRIC VIEW
ENCLOSURE CLAMP
SEE GENERAL NOTES 11-15
FOR MATERIAL SPEC SEE ITEM M6
FRACTIONS DECIMALS ANGLES
± 1/16 ± .X ± 0.1 ± 0.5°
± .XX ± 0.01
± .XXX ± 0.005
DO NOT SCALE DRAWING
DRAWING SIZE ANSI A
NOAA / NOS / CO-OPS
REVISION
PROJECT STATUS
DMES_60X60X15
Components
STATION STRUCTURAL COMPONENTS
D
PRODUCTION S-05 6/8
SPACER
36.0
(.375 REF,
AS SUPPLIED)
.50 (TYP)
15.812±.010
31.624±.010
1.938±.100
4.75
FRONT VIEW
SPACER
SEE GENERAL NOTES 4, 11-15
TOP VIEW
SPACER
SEE GENERAL NOTES 4, 11-15
FOR MATERIAL SPEC SEE ITEM M5 3
Ø.625 (TYP)
6.00
FRACTIONS DECIMALS ANGLES
± 1/16 ± .X ± 0.1 ± 0.5°
± .XX ± 0.01
± .XXX ± 0.005
DO NOT SCALE DRAWING
DRAWING SIZE ANSI A
NOAA / NOS / CO-OPS
REVISION
PROJECT STATUS
DMES_60X60X15
Components
STATION STRUCTURAL COMPONENTS
D
PRODUCTION S-06 7/8
ENCLOSURE BOLT
DOWN BAR
(.25 REF, AS SUPPLIED)
2.00
1.5 27.50
55.00
Ø.875 (TYP)
FRONT VIEW
ENCLOSURE BOLT DOWN BAR
SEE GENERAL NOTES 11-15
TOP VIEW
ENCLOSURE BOLT DOWN BAR
SEE GENERAL NOTES 11-15
58.0
4FOR MATERIAL SPEC SEE ITEM M6
ITEM LIST
ITEM QTY DESCRIPTION REMARKS
M1 3 X 3 X 0.375, ANGLE, 6061-T6 AL -
M2 4 X 3 X 0.375, ANGLE, 6061-T6 AL -
M3 4 X 4 X 0.375, ANGLE, 6061-T6 AL -
M4 4 X 1.647 X 0.247, AM STD CHANNEL, 6061-T6 AL -
M5 0.375 THK, FLAT BAR, 6061-T6 AL -
M6 0.25 THK, FLAT BAR, SS 316 -
M7 7 X 2.11 X 0.230, AM STD CHANNEL, 6061-T6 AL -
1 1 DMES FRAME SEE SH S-01 - S-03 FOR DETAILS
2 3 ENCLOSURE CLAMP SEE SH S-04 FOR DETAILS
3 1 SPACER SEE SH S-05 FOR DETAILS
4 2 ENCLOSURE BOLT DOWN BAR SEE SH S-06 FOR DETAILS
NOAA / NOS / CO-OPS
REVISION
PROJECT STATUS
DMES_60X60X15
Components
STATION STRUCTURAL COMPONENTS
D
PRODUCTION G-01 8/8
ITEM LIST
File details come from the government source that posted it. Updated .