Attachment 13 - Title 1-A 15 percent Design Documents.pdf

TITLE 1-A 15% SUBMITTAL

Design & Construct West Gate Visitors Center, Building 1512

FA460822R0001

Attachment 13

Table of Contents

Existing Conditions & Design Narrative

Outline Specifications

FA460822R0001

Existing Conditions & Design Narrative

FA460822R0001

EXISTING CONDITIONS & DESIGN NARRATIVE

Design & Construct

West Gate Visitors Center, Building 1512

Architectural Existing Conditions

INTERIOR

The intent of this Title 1‐A is to explore the feasibility of renovating and constructing an addition to the Main Gate Visitor Center Building (B1512). All base passes are now processed at this gate and keeping up with the demand is difficult at best. Current wait times sometimes exceed 1 hour. A renovation to the existing

Waiting Room is nearly complete and will provide additional processing capabilities. However, this effort will not fully accommodate the need to quickly accommodate visitors and their pass requests.

The existing facility has one restroom that is shared by both staff and visitors. It is a unisex restroom and according to one of the staff, it is greatly desired to have a

Men’s and Women’s Room. The Restroom has a janitor sink inside and is large enough to accommodate ABA requirements. But one restroom is being taxed by the current volume of use.

There is one private office that is being used to process long term passes. At this time, we understand that there is no need to accommodate more than one private office.

FA460822R0001

The remaining spaces include a Mechanical Closet accessed from the exterior at the South end of the building and a small I.T. Closet, (small by typical base standards). It is nowhere close to 10’x10’ in size which is the usual requirement when renovating or adding onto a building.

The building is not sprinkled and is not required to be, given its occupancy type and occupant load. But the building does accommodate the handicap and appears to be fully ABA compliant at this time.

EXTERIOR

The building has been added onto at least one time. The original gate house is where the new base pass processing area has been built out. It is original to the base and is under the protection of SHPO. No physical modifications can be made to this portion of the structure. The original portion of the building has a red clay tile roof with the rest of the building having the standard red metal standing seam roof. Both new and old exterior walls are covered in EIFS, however the original walls may be plaster. Further inspection will be done if necessary but no work to the original part of the building is anticipated.

FA460822R0001

The building’s main entrance is situated right between the original building and the newer addition along the East side of the building. Currently we anticipate leaving the entrance in its current location continuing to utilize it as the primary entrance.

SITE

There is parking along the East and South side of the existing building.

Additional parking was provided to the South a few years back, but it is not enough to accommodate peak parking needs. Additional parking is currently part of the requested scope of work, however we request further discussion on this topic. If part of this project increases the number of pass‐processing stations then in theory more parking may not be needed – if you are getting people in and out of the visitor center faster, the parking lot won’t be as stressed. Something to consider.

The latest parking addition buts up to the perimeter fence along the South. If parking is added the only logical place to add is inside the secure perimeter of the base.

The existing gates at Wilbur Wright Drive and the corresponding fencing to the West would need to be removed and relocated to the south by approximately 75’.

There is also a “sniffer” on a concrete pad just inside the secure perimeter that would need to be relocated or demolished. We have received word that the sniffer is no longer in use and can be abandoned or demolished, be we are asking for re‐ confirmation prior to calling for its removal.

FA460822R0001

Architectural Proposed

INTERIOR

The end user has requested enough space to accommodate six individual pass‐ processing stations. These stations ideally would be behind a counter but generally open to the public area (not inside of a private office). At least one private office was requested along with new restrooms, one each male and female, and a waiting Room large enough to accommodate k loads.

We are providing a schematic floor plan and site plan in this package. If you refer to the floor plan you will see, we are proposing a complete gut of the interior and a small addition to the building. The center portion of the new building foot print would accommodate a long processing counter large enough to hold six people and all their printing equipment, cameras, etc. The old Waiting Room (the one recently converted to processing) would be converted back to Waiting. The new addition would house new

Restrooms, a Private Office, Mechanical Room, I.T. Closet, and a second Entrance/Exit.

We are not showing a Janitors Sink or Janitor’s Closet at this point. If one is needed, we can accommodate between the two restroom or in another location.

EXTERIOR

The proposed addition would require losing three to four parking spots to the

South of the existing building but would fit well within a fairly confined site bound by the parking lot, a transformer and light poles.

Aesthetically, the addition would match the existing building’s materials and colors with a new red metal standing seam roof and beige EIFS on the walls. New windows and doors would match the existing dark bronze finished aluminum systems.

FA460822R0001

SITE

We propose adding a parking lot in what is currently part of the secure perimeter of the base. We recommend relocating the fence and gates along Wilbur

Wright Drive to accommodate approximately 14 additional parking spots. With the building addition, we lose four spots, so the new parking lot would yield a net gain of 10 parking spaces. Refer to the site plan that is attached as part of this submittal.

ABA

The Facility will meet all ABA requirements. Level landings will need to be provided at all exterior doors.

Life Safety

The existing building and its addition will fully meet all required life safety criteria.

ATFP

We currently can’t meet the requirements for construction defined by ATFP. The vehicle set back distance at our site will be close to zero and the ATFP charts indicate a minimum distance of 16’‐0” to be maintained if the building is constructed of reinforced concrete.

FA460822R0001

Existing Conditions

Mechanical

The existing building is served by a single electric/electric DX split system. The system is a vertical unit located in an exterior mechanical room and consists of a 3.5T air handling unit with supply air ducting routed throughout to ceiling devices within the building spaces. The unit is installed on a platform with a through‐wall return air arrangement with the return air filter grille located in the corridor of the existing building. There is no outside air provided to the unit currently. There is a 3T, R410 condensing unit located on the west side of the building. The HVAC system is controlled by a thermostat located over the unit’s return air grille. The building’s system is not currently connected to the existing campus wide Johnson Controls Metasys control system.

The existing plumbing system is fairly common and standard for a comparable building of its age. The water piping system is copper. The waste/vent system is service weight cast iron and PVC. There is a single restroom with a flush‐tank toilet and drop‐in lavatory. There is a single water cooler with bottle filler and also a small janitor closet with a floor‐mounted mop sink. The water heating systems appears to be a single wall‐ mounted point‐of‐use heater located on the wall above the mop sink and serves the mop sink and restroom lavatory. There is also a lift station on the west side of the building.

The facility is currently not protected throughout by an existing automatic sprinkler system.

FA460822R0001

Electrical

The existing building is served by a small pad mount transformer. The electrical panel is a 225A, 120/208VAC 3‐PH panel. The existing panel shall be replaced to support the power requirements of the new expansion in addition to the existing building.

Existing lighting generally consist of a mixture of recessed cans, and recessed troffers, fluorescent type fixtures with T8 lamping in most occupied spaces.

The facility is served by an existing Monaco Series M addressable fire alarm.

The facility is served by an existing mass notification system.

The existing facility is served with communication system outlets through‐out.

New Construction

Mechanical

The HVAC system will serve the renovated areas and new addition with a single new DX split with electric heat sized for the new space configuration and occupancy loading of the renovation. Ducting serving the existing renovated areas will be reused revised and replaced as need to properly serve all areas of these spaces and duct systems will be added to serve the building addition portion. A new mechanical ventilation system will be provided for the new restrooms and janitor closet providing the required exhaust rate for the spaces. The new COMM closet will be conditioned by a standalone DX heat pump system.

The new restrooms and janitor’s closet will be provided with new fixtures. The existing single station water cooler with bottle filler will be relocated to the new building addition. Water and waste piping will be extended as needed to the new fixture locations. A new electric tank‐type water heater will provide for the new fixtures.

FA460822R0001

The existing is not protected by an automatic fire sprinkler system and is not required to be by code. As of now, the scope of the project is to not provide for a sprinkler system in this renovation.

Electrical

Electrical systems will be designed using the applicable editions of currently enforced federal, military and commercial codes, criteria and guidelines.

Electrical Distribution

Due to floor plan changed, the existing panel serving the building will need to be replaced. A new panelboard will be provided to serve the new facility loads. Branch circuit breakers will be group mounted, manually operated type. The new panelboard will be provided with a separate ground bus, full‐size neutral and integrally mounted transient voltage surge suppression equipment. All panelboard bus shall be copper.

Wiring System

Wiring systems will consist of insulated conductors installed in raceways. Existing power outlets and associated branch circuiting shall be relocated as needed in the area of work. Existing branch circuits will be used as much as possible. Where new branch circuits are required, raceways will be run concealed in finished spaces and may be run exposed in mechanical equipment spaces. Interior raceway will be electrical metallic tubing (EMT). Above grade, exterior raceway will utilize rigid steel galvanized conduit. In ground raceway will be Schedule 40 PVC with pvc coated, rigid steel elbows. Flexible metal conduit will be used for equipment connections with liquid tight flexible conduit used outdoors and other wet location areas.

Branch circuit and control wiring shall be type THHN or THWN, copper, 75deg C rated with 600 volt insulation. Aluminum conductors will not be allowed. Minimum conductor size will be #12awg. A separate, insulated, equipment ground conductor will be run with all branch circuits in addition to the raceway system ground.

All conduits (new and existing) shall be fire‐caulked, as required, to maintain the integrity of the fire rated assembly.

Short Circuit

It is assumed that short‐circuit calculations were performed to establish the expected maximum short circuit current at each point of the distribution system during the original facility design and that the existing equipment was specified

FA460822R0001

accordingly. Therefore, unless the electrical service transformer is required to be changed and upsized, short‐circuit calculations are not planned.

Interior Lighting

The entirety of the interior lighting shall be replaced with new LED type fixtures. The fixtures will be a mixture of recessed cans and 2x4 recessed troffers.

Special Systems

Interior Communications

Additional comm outlets will be added in the expanded portion of the building as well as the renovated existing portion to serve the new computer stations.

Fire Alarm/Mass Notification

New fire alarm and Mass notification devices will be added to the expanded portion of the building and existing devices will be relocated per the floor plan changes to the existing portion of the building. All new devices will match the existing systems. The existing FACP shall be relocated to the new Elec/Mech room.

FA460822R0001

Outline Specifications

FA460822R0001

OUTLINE SPECIFICATIONS Construct VCC Expansion, Building 1512

PROJECT SUMMARY

The project consists of the construction of additional office space at the West Gate Visitor Center (B1512). The new building addition will be constructed of similar construction as the existing visitor center. Construction shall include but not be limited to partial renovation of the existing structure and an addition structure that matches the existing construction.

DIVISION 1 – GENERAL REQUIREMENTS

01732 Selective Demolition – Selective demolition shall consist of removal of an existing reception counter, toilet rooms, I.T. closet, and Mechanical Room. Also some existing exterior walls may need to be removed depending on what construction type is acceptable. It shall be the responsibility of the Contractor to notify the Owner and provide for the abatement and disposal of all asbestos materials in a legally authorized method approved by Barksdale Air Force Base.

DIVISION 3 – CONCRETE

Concrete work will include a new slab, partial sidewalk extension, and expanding the parking lot. If a high level of blast protection is required, then reinforced concrete walls will need to be included.

DIVISION 4 – MASONRY

04200 Unit Masonry - Masonry work will consist of a split faced CMU wainscot if required. There is no wainscot to match at this time.

DIVISION 5 – METALS

05120 Structural Steel Framing – Steel will be required depending on the level of blast protection that is acceptable. If a high level of blast protection is required then we will need to use steel as part of our roof structure. If a low level of blast protection is required then we will need to use metal stud wall framing as part of the overall construction.

DIVISION 6 – WOOD PLASTICS AND COMPOSITES

Section 06100 Rough Carpentry - Carpentry includes blocking, furring, and bracing.

Wood species shall be fir or southern yellow pine no. 2 grade. Fire retardant lumber for blocking shall be used in areas requiring fire-rated construction.

FA460822R0001

DIVISION 7 – THERMAL AND MOISTURE PROTECTION

Section 07210 Building Insulation – Concrete masonary unit wall insulation shall be poured loose fill perlite insulation placed in the hollow cavity of each CMU block.

Sound attenuation insulating batts shall be placed between studs at interior walls where indicated and as specified.

Section 07242 Exterior Insulation and Finish Systems – EIFS will be used as an exterior finish system for this project.

Section 07610 Sheet Metal Roofing – Sheet metal roofing shall be standing seam snap lock type. Roof deck insulation shall be 3” polyisocyanurate composite board with OSB material attached to the exterior face Provide all necessary roofing accessories, trim and flashing for a complete watertight installation. Color shall be base standard “Colonial Red”.

Section 07620 Sheet Metal Flashing and Trim – Sheet metal flashing and trim shall consist of custom fabricated roof and wall flashings, roof drainage systems, reglets and through-wall flashing of sizes and shapes indicated on Drawings and as specified. Provide gutter and downspout as specified and where indicated on Plans.

Exposed surfaces shall match Base Architectural Standards “Colonial Red”.

Section 07841 Through-Penetration Firestopping – Firestopping shall consist of approved UL systems specifically designed for each individual condition for fire-resistance rated walls, horizontal assemblies, and smoke barriers.

Section 07920 Joint Sealants – Elastomeric sealants applied to the juncture of similar and dissimilar materials compatible to adjoining substrates. Manufacturer’s recommended primers and sealant backers shall be provided where necessary for a complete sealant installation. Sealants shall be paintable. resistance rated walls, horizontal assemblies, and smoke barriers.

DIVISION 8 – OPENINGS

Section 08110 Hollow Metal Doors and Frames – Exterior doors shall be flush galvanized face hollow metal doors factory primed and prepared to receive specified hardware. Exterior doorframes for hollow metal doors shall be one piece welded hollow metal frames of heights, thicknesses, and gauge specified and indicated on the plans. Exterior frames shall be galvanized factory primed and prepared to receive specified hardware. Interior doorframes shall be one piece welded hollow metal frames of heights, thicknesses, and gauge specified and indicated on the plans.

Frames shall be primed and factory prepared to receive specified hardware.

Section 08410 Aluminum Entrances and Storefronts – new windows will be provided for each new office to match existing aluminum window system. if blast protection is required then we will need to have a structural engineer design the connection details from the window to the exterior walls.

FA460822R0001

Section 08710 Door Hardware - Hardware sets shall be specified for each door complete with all items necessary for code compliance and proper operation.

Provide lever type handles on door opening devices to comply with ADAAG requirements. Provided electronic hardware at specific door locations as called for and specified. Coordinate electronic locks and strikes with base security operations.

Keying shall be in accordance with Owner’s established keying system.

DIVISION 9 – FINISHES

Section 09250 Gypsum Board - Gypsum board shall be 5/8" Type X gypsum wall board screw attached to metal stud framing, taped and floated to receive final finish as specified, and indicated on the plans. Gypsum board ceilings where indicated shall be same thickness as wall board installed on specified grid system supported from structure above.

Section 09511 Acoustical Panel Ceilings – Suspended acoustical ceiling shall be mineral felted type with fissured pattern as specified. Ceiling panels shall be set in 2 foot x 2 foot metal lay in grid. Grid and panels shall be set at height indicated on Plans and set level with floor surface. Provide and install acoustical sealant as specified for sound attenuation in acoustic ceilings.

Section 09651 Resilient Floor Tile – Vinyl composition tile shall be 12 inch by 12 inch by 1/8 inch size with full through color patterns. Installation shall be with manufacturer approved adhesive over prepared concrete slab with approved moisture content per manufacturer’s warranty requirements before installation.

Section 09653 Resilient Wall Base and Accessories – Rubber base shall be 4-inch high top set cove at VCT installation and straight toe installation where called for at carpet areas adhered substrate with manufacturer’s approved adhesive. Provide and install rubber nosings, treads and floor tile for the steps and landings at new metal stairs. Install with adhesive for indicated substrates that is recommended by specific manufacturer. Color shall be as selected by Owner’s Representative.

Section 09912 Painting - Finished painted surfaces where indicated shall be composed of suitable substrate primer, and two finish coats of paint of type specified for the environment in which the finish will be exposed. Paint for each individual substrate shall conform to the Master Painters Index to insure proper VOC contents are followed and in accordance with jurisdictional authorities.

DIVISION 10 – SPECIALTIES

Section 10431 Signage – Interior signs shall be provided for each individual area of size and type to be in compliance with ADA and other regulatory requirements.

Mounting shall be by concealed method for the substrate to which it shall be attached. Exterior signs shall be of material, size, and lettering style indicated on the Plans. Exterior signage shall be installed per method specified and at location indicated on Plans.

FA460822R0001

Section 10522 Fire Extinguisher Cabinets – Cabinets shall be semi-recessed porcelain coated steel construction to hold fire extinguisher of size and type required.

Cabinets shall be designed for installation in fire rated walls where necessary.

Cabinet faces shall be aluminum with glass fronts and identification lettering.

Mounting height shall be no higher than 48 inches to the center of the cabinet.

Section 10523 Fire Extinguishers – Extinguishers shall be 10 lb. nominal capacity for use in extinguishing A, B, and C type fires.

DIVISION 11 – EQUIPMENT

None

DIVISION 12 – FURNISHINGS

No furniture anticipated at this time

DIVISION 13 – FIRE SUPPRESSION - IF REQUIRED

Section 13050 Common Work Requirements for Fire Suppression – Basic directions and definitions including all related labor, materials, equipment, etc. as required completing all fire suppression work.

Section 13915 Fire Suppression Piping – Piping, specialties, valves and sprinklers for fire suppression systems.

DIVISION 15 – MECHANICAL

Section 15010 General Provisions – Basic mechanical directions and definitions including all related labor, materials, equipment, etc. as required to complete all mechanical work.

Section 15050 Basic Mechanical Materials and Methods – Description of various mechanical materials and associated construction methods for various mechanical systems.

Section 15055 Motors – General descriptions, characteristics and requirements associated with electrical motors of the various mechanical systems.

Section 15060 Hangers and Supports – Support and suspension arrangements and components for the various mechanical pipe and duct systems.

Section 15071 Mechanical Vibration Controls – General descriptions, characteristics and requirements of vibration control components and systems in conjunction with the various mechanical systems.

Section 15075 Mechanical Identification – Identification requirements and components for mechanical equipment, ductwork, and piping.

FA460822R0001

Section 15080 Mechanical Insulation – Insulation materials and installation methods for various duct, equipment and pipe systems.

Section 15081 Duct Insulation – Insulation materials and installation methods for various ductwork systems.

Section 15110 Valves – Valve requirements for each building piping system.

Section 15121 Pipe Expansion Fittings and Loops – General characteristics, components and requirements related to expansion of the hydronic mechanical pipe system.

Section 15122 Meters and Gages – General characteristics, components and requirements related to fluid measurement devices of the hydronic mechanical pipe system.

Section 15140 Domestic Water Piping – Potable water piping distribution system within the building.

Section 15145 Domestic Water Piping Specialties – Specialties, valves, and fittings for domestic water piping.

Section 15150 Sanitary Waste and Vent Piping – Sanitary waste and vent piping collection system within the building.

Section 15155 Drainage Piping Specialties – Floor, trench, and roof drains;

interceptors; and specialties for drainage piping.

Section 15180 Equipment Insulation – Insulation materials and installation methods for various mechanical system components.

Section 15183 Refrigerant Piping – Piping, specialties, and refrigerant for HVAC systems.

Section 15410 Plumbing Fixtures – Plumbing fixture materials, associated components, and installation requirements.

Section 15415 Drinking Fountains and Water Coolers – Electric water coolers and fountains.

Section 15430 Plumbing Specialties – Miscellaneous plumbing components of the domestic water, waste, and vent piping systems.

Section 15485 Electric Water Heaters – Water heater, associated components, and installation requirements.

Section 15738 Split-System Air-Conditioning Units – Unitary direct expansion (DX) coil air-handling unit with air-cooled outdoor condensing unit serving dedicated HVAC zone.

FA460822R0001

Section 15767 Unit Heaters – Hot water, steam, and electric house unit heaters.

Section 15815 Metal Ducts – Duct material and associated installation requirements for various building HVAC systems.

Section 15820 Duct Accessories – Miscellaneous HVAC components associated with the various duct systems.

Section 15838 Power Ventilators – Exhaust fan type and construction parameters including installation requirements for building exhaust ventilation.

Section 15855 Diffusers, Registers, and Grilles – HVAC system air distribution device descriptions, associated components, and installation parameters.

Section 15861 Air Filters – General descriptions and characteristics of air filters of the various HVAC equipment.

Section 15900 HVAC Control System – General descriptions and characteristics of the temperature control/building automation system.

Section 15950 Testing, Balancing, and Adjusting – Evaluations and adjustments of the installed HVAC systems including detailed report to achieve system design and functionality.

DIVISION 16 – ELECTRICAL

Section 16010 General Provisions -- Electrical equipment coordination, submittal requirements, sleeves and sleeve seals for raceways and cables as well as common electrical installation requirements

Section 16050 Basic Materials and Methods -- All wire shall be copper, minimum 95% conductivity. Insulation to be THWN or THHN, rated 600 volts, 75deg C, minimum. Number 10awg and smaller shall be solid or stranded copper, larger conductors shall be stranded copper. Minimum conductor size shall be #12awg. All interior and exterior equipment shall be labeled as to its’ designation and feeding circuit. Wiring device plates shall be provided with clear labels indicating the connected branch circuit.

Section 16060 Grounding and Bonding –An insulated equipment grounding conductor shall be included with all circuit runs, in addition to the raceway system as a grounding conductor.

Section 16130 Raceways and Boxes – In office and administrative areas, interior raceway shall be electrical metallic tubing (EMT). In hangar areas and above grade, exterior, raceway will utilize rigid steel galvanized conduit. In ground raceway will be Schedule 40 PVC with pvc coated, rigid steel elbows. Flexible metal conduit will be used for equipment connections with liquid tight flexible conduit used outdoors and in wet locations. Cable trough/basket wireway and/or j-hooks shall be used for communication wiring homeruns.

FA460822R0001

Section 16140 Wiring Devices – All receptacles will be specification grade, duplex type, 20amp, 120volt service. All switches will be specification grade, quiet type snap switches, rated for 20amp service, 120/277volt. Fluorescent dimmer switch/ballast combinations shall be capable of smooth dimming down to 10% of the full brightness.

Wall plates shall be stainless steel.

Section 16145 Lighting Control Devices – Indoor occupancy sensors shall be ceiling or wall-switch mounted, dual-technology type.

Section 16442 Panelboards – Panelboards shall be surface mount, NEMA 1 type.

All panelboard bus shall be copper. Branch circuit breakers shall be full-module, bolt on type. Circuit breakers shall be fully rated with an interrupting rating equal to that of the panelboard. Panelboards will be provided with main circuit breakers unless located within line of sight of the serving source, in which case, main lug only panels will be specified. Panelboards shall have an integral surge protective device.

Section 16511 Interior Lighting – Linear fluorescent fixtures shall utilize 4ft, 32watt, T8 lamps with NEMA premium ballasts, PS, NBF, except where dimmable ballasts are required. All interior fluorescent fixtures to have an LER greater than 77. Lamps shall be 3500K with a minimum CRI of 80. Exit signs shall have integral, maintenance free batteries for emergency service and be internally lit with LED lamps.

Section 16721 Fire Alarm System – The fire alarm system shall be a Monaco non-coded, digital, addressable system in accordance with NFPA 72, NFPA 70 and UFC 3-600-1 with wireless reporting to the base fire station.

End of Specifications

FA460822R0001

PROJECT LOCATION MAP

S

E

C

U

R

IT

Y

FLIGHTLINE

LINDBERGH

T

W

I N

I N

G

L

U

K

E

D

A

V

I

S

C

O

N

V O

Y

W

I

L

B

U

R

W

I

G

H

T

C

U

R

T

I S

S

S

P

A

A

T

Z

K

E

N

N

E

Y

L

A

N

G

L

E

Y

S

H

R

E

V

E

P

O

R

T

B

O

S

S

I

E

R

S

E

L

F

R

I

D

G

E

B A

R K

S D

A L

E

H

A

P

N

O

L

D

E

A

R

H

A

R

T

B

O

N

G

I C

A R

U S

D

O

U

H

E

T

L

O

G

I S

T

I C

S

I

E

K

E

R

L

O

U

I

S

I

A

N

A

R

E

A

D

I N

E

S

S

C

H

E

N

N

A

U

L

T

FOULOIS

M

O

N

T

G

O

L

F

I

E

R

R

I

C

K

E

N

B

A

C

K

E

R

B

I

L

L

Y

M

I

T

C

H

E

L

L

F A

I R

C H

I L

D

D

A

E

D

A

L

U

S

V A

N D

E N

B E

R G

O R

V I L

I G

H T

C H

A P

P

J

M E

S

B

L V

D

N

A

F A

I R

C H

I L

D

K E

N N

E Y

V

A

N

D

E

N

B

E

R

G

F

A

I

R

C

H

I

L

D

F

A

I

R

C

H

I

L

D

S H

R E

V E

P O

R T

N

A

R I C

K E

N B

A C

K E

R

K

E

N

N

E

Y

N A

N

A

V

A

N

D

E

N

B

E

R

G

B I L

M

T

C H

E L

L

O

R

V

I

L

I

G

H

T

D

O

U

H

E

T

R

I

C

K

E

N

B

A

C

K

E

R

B

O

S

S

I

E

R

DAVIS

S

E

C

U

R

I T

ENLARGED SITE PLAN

PRELIMINARY

NOT FOR

CONSTRUCTION

DRAWING INDEX

ARCHITECTURAL

ABBREVIATIONS

MATERIAL INDEX

SYMBOLS LEGEND

A1

A2.1

A2.2

A3.1

MECHANICAL

MD1.1

M1.1

ED1.1

ES1.1

E1.1

ELECTRICAL

FA460822R0001

TEXT INFO

TEXT

DETAIL

A-

RKF

WKB

DETAIL ELEVATION

ELEVATIONDETAIL

DEMOLITION SITE PLAN

PRELIMINARY

NOT FOR

CONSTRUCTION

FA460822R0001

TEXT INFO

TEXT

DETAIL

A-

RKF

WKB

DETAIL ELEVATION

ELEVATIONDETAIL

PROPOSED SITE PLAN

PRELIMINARY

NOT FOR

CONSTRUCTION

FA460822R0001

PRELIMINARY

NOT FOR

CONSTRUCTION

DEMOLITION PLAN

PROPOSED PLAN

GENERAL NOTES

DEMOLITION NOTES

CONSTRUCTION NOTES

WALL TYPE LEGEND

FA460822R0001

EXTG 3.5T AHU

EXTG EF

T

EXTG 3T CU

EXTG 3KW IEWH

RETAIN EXISTING EWCH FOR

RELOCATION (RE: SHEET M1.1)

EXISTING WALL

FAUCET TO REMAIN

THESE DRAWINGS DO NOT INCLUDE NECESSARY

COMPONENTS FOR CONSTRUCTION SAFETY.

18-165

ENGINEER:

LICENSE NO.

COPYRIGHT NOTICE:

THIS ENGINEERING DRAWING SHALL BE USED ONLY PURSUANT TO THE AGREEMENT WITH AFJMC. NO

OTHER USE DISSEMINATION OR DUPLICATION MAY BE MADE WITHOUT PRIOR WRITTEN CONSENT OF AFJMC.

ALL COMMON LAW RIGHTS OF COPYRIGHT AND OTHERWISE ARE HEREBY SPECIFICALLY RESERVED.

NOT TO BE USED FOR

CONSTRUCTION,

BIDDING,

RECORDATION,

CONVEYANCE, SALES,

OR AS THE BASIS FOR

THE ISSUANCE OF A

PERMIT

PRELIMINARY

SCALE: 1/4"=1'-0"

1.

LEGEND

(MECHANICAL ITEMS ONLY)

EXISTING TO REMAIN

EXISTING TO BE REMOVED

SCALE: 1/4"=1'-0"

FA460822R0001

Attachment 13

AutoCAD SHX Text

EXISTING VISITOR CENTER

AutoCAD SHX Text

EXIST. OFF.

AutoCAD SHX Text

ELEC./ MECH.

AutoCAD SHX Text

TELE./ COMM.

AutoCAD SHX Text

EXIST. CORR.

AutoCAD SHX Text

TOIL.

AutoCAD SHX Text

JAN

AutoCAD SHX Text

EXISTING VISITOR CENTER

AutoCAD SHX Text

EXIST. OFF.

AutoCAD SHX Text

ELEC./ MECH.

AutoCAD SHX Text

TELE./ COMM.

AutoCAD SHX Text

EXIST. CORR.

AutoCAD SHX Text

TOIL.

AutoCAD SHX Text

JAN

AutoCAD SHX Text Drawing Number

AutoCAD SHX Text Facility Number

AutoCAD SHX Text Project Number

AutoCAD SHX Text

PROJECT TITLE

AutoCAD SHX Text

SHEET

AutoCAD SHX Text

SHEET TITLE

AutoCAD SHX Text

OF

AutoCAD SHX Text

REVISION

AutoCAD SHX Text

BY/DATE

AutoCAD SHX Text Designer

AutoCAD SHX Text Drafter

AutoCAD SHX Text Project Manager

AutoCAD SHX Text Date

AutoCAD SHX Text

DESIGN FIRM

AutoCAD SHX Text Engineer

AutoCAD SHX Text Pavements

AutoCAD SHX Text Engineer

AutoCAD SHX Text Corrosion

AutoCAD SHX Text Protective

AutoCAD SHX Text Engineer

AutoCAD SHX Text Coating Engr.

AutoCAD SHX Text Fire Chief

AutoCAD SHX Text Operations

AutoCAD SHX Text Chief of

AutoCAD SHX Text Construction

AutoCAD SHX Text Roofing

AutoCAD SHX Text Management

AutoCAD SHX Text

COORDINATION

AutoCAD SHX Text Computers

AutoCAD SHX Text Engineer

AutoCAD SHX Text Systems

AutoCAD SHX Text Security

AutoCAD SHX Text Police

AutoCAD SHX Text Security

AutoCAD SHX Text Bioenvironmental

AutoCAD SHX Text Airfield

AutoCAD SHX Text Safety

AutoCAD SHX Text Ground

AutoCAD SHX Text Manager

AutoCAD SHX Text Communication

AutoCAD SHX Text

APPROVED

AutoCAD SHX Text

SIGNATURE

AutoCAD SHX Text Chief of

AutoCAD SHX Text Engineering

AutoCAD SHX Text Design

AutoCAD SHX Text Chief of

AutoCAD SHX Text Contracting

AutoCAD SHX Text User

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text Engineer

AutoCAD SHX Text Civil

AutoCAD SHX Text Air Force Base

AutoCAD SHX Text Barksdale

AutoCAD SHX Text Louisiana

AutoCAD SHX Text

DESIGN FIRM

AutoCAD SHX Text

NOVEMBER 2018

AutoCAD SHX Text 2M

AutoCAD SHX Text

RKC

AutoCAD SHX Text

CMH

AutoCAD SHX Text

KDR

AutoCAD SHX Text

TITLE 1-A 15%%%

AutoCAD SHX Text

6 NOV 2018

AutoCAD SHX Text B1512

AutoCAD SHX Text

OPP. NO. 1072069

AutoCAD SHX Text

BARKSDALE AIR FORCE

AutoCAD SHX Text

BASE, LOUISIANA 71110

AutoCAD SHX Text

CONSTRUCT VCC EXPANSION

AutoCAD SHX Text

BUILDING 1512

AutoCAD SHX Text

MD1.1

AutoCAD SHX Text

MECHANICAL DEMOLITION PLANS

AutoCAD SHX Text

MECHANICAL DEMOLITION PLAN

AutoCAD SHX Text

%%UMECHANICAL NOTES%%U:

AutoCAD SHX Text

PLUMBING DEMOLITION PLAN

EXHAUST FAN

AHU

T

CU

FCU

CU

WCHWCH

LHLH

RELOCATED EWCH

(RE: SHEET MD1.1)

3"FD/TP 3"FD/TP

3"FD/TP

THESE DRAWINGS DO NOT INCLUDE NECESSARY

COMPONENTS FOR CONSTRUCTION SAFETY.

18-165

ENGINEER:

LICENSE NO.

COPYRIGHT NOTICE:

THIS ENGINEERING DRAWING SHALL BE USED ONLY PURSUANT TO THE AGREEMENT WITH AFJMC. NO

OTHER USE DISSEMINATION OR DUPLICATION MAY BE MADE WITHOUT PRIOR WRITTEN CONSENT OF AFJMC.

ALL COMMON LAW RIGHTS OF COPYRIGHT AND OTHERWISE ARE HEREBY SPECIFICALLY RESERVED.

NOT TO BE USED FOR

CONSTRUCTION,

BIDDING,

RECORDATION,

CONVEYANCE, SALES,

OR AS THE BASIS FOR

THE ISSUANCE OF A

PERMIT

PRELIMINARY

SCALE: 1/4"=1'-0"

SCALE: 1/4"=1'-0"

1.

LEGEND

(MECHANICAL ITEMS ONLY)

EXISTING TO REMAIN

NEW WORK

FA460822R0001

Attachment 13

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text

UNISEX 1

AutoCAD SHX Text

UNISEX 2

AutoCAD SHX Text

CORR. 1

AutoCAD SHX Text

MECH./ ELEC.

AutoCAD SHX Text

TELE./ COMM.

AutoCAD SHX Text

WAITING

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text

UNISEX 1

AutoCAD SHX Text

UNISEX 2

AutoCAD SHX Text

CORR. 1

AutoCAD SHX Text

MECH./ ELEC.

AutoCAD SHX Text

TELE./ COMM.

AutoCAD SHX Text

WAITING

AutoCAD SHX Text Drawing Number

AutoCAD SHX Text Facility Number

AutoCAD SHX Text Project Number

AutoCAD SHX Text

PROJECT TITLE

AutoCAD SHX Text

SHEET

AutoCAD SHX Text

SHEET TITLE

AutoCAD SHX Text

OF

AutoCAD SHX Text

REVISION

AutoCAD SHX Text

BY/DATE

AutoCAD SHX Text Designer

AutoCAD SHX Text Drafter

AutoCAD SHX Text Project Manager

AutoCAD SHX Text Date

AutoCAD SHX Text

DESIGN FIRM

AutoCAD SHX Text Engineer

AutoCAD SHX Text Pavements

AutoCAD SHX Text Engineer

AutoCAD SHX Text Corrosion

AutoCAD SHX Text Protective

AutoCAD SHX Text Engineer

AutoCAD SHX Text Coating Engr.

AutoCAD SHX Text Fire Chief

AutoCAD SHX Text Operations

AutoCAD SHX Text Chief of

AutoCAD SHX Text Construction

AutoCAD SHX Text Roofing

AutoCAD SHX Text Management

AutoCAD SHX Text

COORDINATION

AutoCAD SHX Text Computers

AutoCAD SHX Text Engineer

AutoCAD SHX Text Systems

AutoCAD SHX Text Security

AutoCAD SHX Text Police

AutoCAD SHX Text Security

AutoCAD SHX Text Bioenvironmental

AutoCAD SHX Text Airfield

AutoCAD SHX Text Safety

AutoCAD SHX Text Ground

AutoCAD SHX Text Manager

AutoCAD SHX Text Communication

AutoCAD SHX Text

APPROVED

AutoCAD SHX Text

SIGNATURE

AutoCAD SHX Text Chief of

AutoCAD SHX Text Engineering

AutoCAD SHX Text Design

AutoCAD SHX Text Chief of

AutoCAD SHX Text Contracting

AutoCAD SHX Text User

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text Engineer

AutoCAD SHX Text Civil

AutoCAD SHX Text Air Force Base

AutoCAD SHX Text Barksdale

AutoCAD SHX Text Louisiana

AutoCAD SHX Text

DESIGN FIRM

AutoCAD SHX Text

NOVEMBER 2018

AutoCAD SHX Text 2M

AutoCAD SHX Text

RKC

AutoCAD SHX Text

CMH

AutoCAD SHX Text

KDR

AutoCAD SHX Text

TITLE 1-A 15%%%

AutoCAD SHX Text

6 NOV 2018

AutoCAD SHX Text B1512

AutoCAD SHX Text

OPP. NO. 1072069

AutoCAD SHX Text

BARKSDALE AIR FORCE

AutoCAD SHX Text

BASE, LOUISIANA 71110

AutoCAD SHX Text

CONSTRUCT VCC EXPANSION

AutoCAD SHX Text

BUILDING 1512

AutoCAD SHX Text M1.1

AutoCAD SHX Text

MECHANICAL PLANS

AutoCAD SHX Text

HVAC PLAN

AutoCAD SHX Text

PLUMBING PLAN

%%UMECHANICAL NOTES%%U:

THESE DRAWINGS DO NOT INCLUDE NECESSARY

COMPONENTS FOR CONSTRUCTION SAFETY.

18-165

ENGINEER:

LICENSE NO.

COPYRIGHT NOTICE:

THIS ENGINEERING DRAWING SHALL BE USED ONLY PURSUANT TO THE AGREEMENT WITH AFJMC. NO

OTHER USE DISSEMINATION OR DUPLICATION MAY BE MADE WITHOUT PRIOR WRITTEN CONSENT OF AFJMC.

ALL COMMON LAW RIGHTS OF COPYRIGHT AND OTHERWISE ARE HEREBY SPECIFICALLY RESERVED.

NOT TO BE USED FOR

CONSTRUCTION,

BIDDING,

RECORDATION,

CONVEYANCE, SALES,

OR AS THE BASIS FOR

THE ISSUANCE OF A

PERMIT

PRELIMINARY

SCALE: 1/8"=1'-0"

1. EXISTING PAD MOUNT TRANSFORMER.

FA460822R0001

Attachment 13

AutoCAD SHX Text

EXISTING CONC. WALK

AutoCAD SHX Text

EXISTING VISITOR CENTER

AutoCAD SHX Text

EXISTING CONC. WALK

AutoCAD SHX Text Drawing Number

AutoCAD SHX Text Facility Number

AutoCAD SHX Text Project Number

AutoCAD SHX Text

PROJECT TITLE

AutoCAD SHX Text

SHEET

AutoCAD SHX Text

SHEET TITLE

AutoCAD SHX Text

OF

AutoCAD SHX Text

REVISION

AutoCAD SHX Text

BY/DATE

AutoCAD SHX Text Designer

AutoCAD SHX Text Drafter

AutoCAD SHX Text Project Manager

AutoCAD SHX Text Date

AutoCAD SHX Text

DESIGN FIRM

AutoCAD SHX Text Engineer

AutoCAD SHX Text Pavements

AutoCAD SHX Text Engineer

AutoCAD SHX Text Corrosion

AutoCAD SHX Text Protective

AutoCAD SHX Text Engineer

AutoCAD SHX Text Coating Engr.

AutoCAD SHX Text Fire Chief

AutoCAD SHX Text Operations

AutoCAD SHX Text Chief of

AutoCAD SHX Text Construction

AutoCAD SHX Text Roofing

AutoCAD SHX Text Management

AutoCAD SHX Text

COORDINATION

AutoCAD SHX Text Computers

AutoCAD SHX Text Engineer

AutoCAD SHX Text Systems

AutoCAD SHX Text Security

AutoCAD SHX Text Police

AutoCAD SHX Text Security

AutoCAD SHX Text Bioenvironmental

AutoCAD SHX Text Airfield

AutoCAD SHX Text Safety

AutoCAD SHX Text Ground

AutoCAD SHX Text Manager

AutoCAD SHX Text Communication

AutoCAD SHX Text

APPROVED

AutoCAD SHX Text

SIGNATURE

AutoCAD SHX Text Chief of

AutoCAD SHX Text Engineering

AutoCAD SHX Text Design

AutoCAD SHX Text Chief of

AutoCAD SHX Text Contracting

AutoCAD SHX Text User

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text Engineer

AutoCAD SHX Text Civil

AutoCAD SHX Text Air Force Base

AutoCAD SHX Text Barksdale

AutoCAD SHX Text Louisiana

AutoCAD SHX Text

DESIGN FIRM

AutoCAD SHX Text

NOVEMBER 2018

AutoCAD SHX Text

RKC

AutoCAD SHX Text

DWB

AutoCAD SHX Text

DWB

AutoCAD SHX Text 3E

AutoCAD SHX Text

TITLE 1-A 15%%%

AutoCAD SHX Text

6 NOV 2018

AutoCAD SHX Text B1512

AutoCAD SHX Text

OPP. NO. 1072069

AutoCAD SHX Text

BARKSDALE AIR FORCE

AutoCAD SHX Text

BASE, LOUISIANA 71110

AutoCAD SHX Text

CONSTRUCT VCC EXPANSION

AutoCAD SHX Text

BUILDING 1512

AutoCAD SHX Text

ES1.1

AutoCAD SHX Text

ELECTRICAL SITE PLAN

AutoCAD SHX Text

ELECTRICAL SITE PLAN

%%UELECTRICAL NOTES%%U:

EXISTING PANEL

EXISTING FACP

TYP.

<RL>

THESE DRAWINGS DO NOT INCLUDE NECESSARY

COMPONENTS FOR CONSTRUCTION SAFETY.

18-165

ENGINEER:

LICENSE NO.

COPYRIGHT NOTICE:

THIS ENGINEERING DRAWING SHALL BE USED ONLY PURSUANT TO THE AGREEMENT WITH AFJMC. NO

OTHER USE DISSEMINATION OR DUPLICATION MAY BE MADE WITHOUT PRIOR WRITTEN CONSENT OF AFJMC.

ALL COMMON LAW RIGHTS OF COPYRIGHT AND OTHERWISE ARE HEREBY SPECIFICALLY RESERVED.

NOT TO BE USED FOR

CONSTRUCTION,

BIDDING,

RECORDATION,

CONVEYANCE, SALES,

OR AS THE BASIS FOR

THE ISSUANCE OF A

PERMIT

PRELIMINARY

SCALE: 1/4"=1'-0"

1. EXISTING PANEL WILL BE DEMO'D.

2. DEMO ALL EXISTING RECEPTACLES AND DATA OUTLETS

IN WALLS TO BE DEMO'D.

3. EXISTING FIRE ALARM PANEL SHALL BE RELOCATED TO

NEW ELECTRICAL ROOM. REF. SHEET E1.1.

SCALE: 1/4"=1'-0"

NOTE: ALL EXISTING INTERIOR LIGHTING SHALL BE DEMO'D.

FA460822R0001

Attachment 13

AutoCAD SHX Text

EXISTING VISITOR CENTER

AutoCAD SHX Text

EXIST. OFF.

AutoCAD SHX Text

ELEC./ MECH.

AutoCAD SHX Text

TELE./ COMM.

AutoCAD SHX Text

EXIST. CORR.

AutoCAD SHX Text

TOIL.

AutoCAD SHX Text

JAN

AutoCAD SHX Text

UNISEX 1

AutoCAD SHX Text

TELE./ COMM.

AutoCAD SHX Text

WAITING

AutoCAD SHX Text

UNISEX 2

AutoCAD SHX Text

MECH./ ELEC.

AutoCAD SHX Text

EXISTING VISITOR CENTER

AutoCAD SHX Text

EXIST. OFF.

AutoCAD SHX Text

ELEC./ MECH.

AutoCAD SHX Text

TELE./ COMM.

AutoCAD SHX Text

EXIST. CORR.

AutoCAD SHX Text

TOIL.

AutoCAD SHX Text

JAN

AutoCAD SHX Text

UNISEX 1

AutoCAD SHX Text

TELE./ COMM.

AutoCAD SHX Text

WAITING

AutoCAD SHX Text Drawing Number

AutoCAD SHX Text Facility Number

AutoCAD SHX Text Project Number

AutoCAD SHX Text

PROJECT TITLE

AutoCAD SHX Text

SHEET

AutoCAD SHX Text

SHEET TITLE

AutoCAD SHX Text

OF

AutoCAD SHX Text

REVISION

AutoCAD SHX Text

BY/DATE

AutoCAD SHX Text Designer

AutoCAD SHX Text Drafter

AutoCAD SHX Text Project Manager

AutoCAD SHX Text Date

AutoCAD SHX Text

DESIGN FIRM

AutoCAD SHX Text Engineer

AutoCAD SHX Text Pavements

AutoCAD SHX Text Engineer

AutoCAD SHX Text Corrosion

AutoCAD SHX Text Protective

AutoCAD SHX Text Engineer

AutoCAD SHX Text Coating Engr.

AutoCAD SHX Text Fire Chief

AutoCAD SHX Text Operations

AutoCAD SHX Text Chief of

AutoCAD SHX Text Construction

AutoCAD SHX Text Roofing

AutoCAD SHX Text Management

AutoCAD SHX Text

COORDINATION

AutoCAD SHX Text Computers

AutoCAD SHX Text Engineer

AutoCAD SHX Text Systems

AutoCAD SHX Text Security

AutoCAD SHX Text Police

AutoCAD SHX Text Security

AutoCAD SHX Text Bioenvironmental

AutoCAD SHX Text Airfield

AutoCAD SHX Text Safety

AutoCAD SHX Text Ground

AutoCAD SHX Text Manager

AutoCAD SHX Text Communication

AutoCAD SHX Text

APPROVED

AutoCAD SHX Text

SIGNATURE

AutoCAD SHX Text Chief of

AutoCAD SHX Text Engineering

AutoCAD SHX Text Design

AutoCAD SHX Text Chief of

AutoCAD SHX Text Contracting

AutoCAD SHX Text User

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text Engineer

AutoCAD SHX Text Civil

AutoCAD SHX Text Air Force Base

AutoCAD SHX Text Barksdale

AutoCAD SHX Text Louisiana

AutoCAD SHX Text

DESIGN FIRM

AutoCAD SHX Text

NOVEMBER 2018

AutoCAD SHX Text

RKC

AutoCAD SHX Text

DWB

AutoCAD SHX Text

DWB

AutoCAD SHX Text 3E

AutoCAD SHX Text

TITLE 1-A 15%%%

AutoCAD SHX Text

6 NOV 2018

AutoCAD SHX Text B1512

AutoCAD SHX Text

OPP. NO. 1072069

AutoCAD SHX Text

BARKSDALE AIR FORCE

AutoCAD SHX Text

BASE, LOUISIANA 71110

AutoCAD SHX Text

CONSTRUCT VCC EXPANSION

AutoCAD SHX Text

BUILDING 1512

AutoCAD SHX Text

ED1.1

AutoCAD SHX Text

ELECTRICAL DEMOLITION PLANS

AutoCAD SHX Text

LIGHTING DEMOLITION PLAN

AutoCAD SHX Text

%%UELECTRICAL NOTES%%U:

POWER & SYSTEMS DEMOLITION PLAN

PANEL "LP"

EXISTING FACP

<RE>

THESE DRAWINGS DO NOT INCLUDE NECESSARY

COMPONENTS FOR CONSTRUCTION SAFETY.

18-165

ENGINEER:

LICENSE NO.

COPYRIGHT NOTICE:

THIS ENGINEERING DRAWING SHALL BE USED ONLY PURSUANT TO THE AGREEMENT WITH AFJMC. NO

OTHER USE DISSEMINATION OR DUPLICATION MAY BE MADE WITHOUT PRIOR WRITTEN CONSENT OF AFJMC.

ALL COMMON LAW RIGHTS OF COPYRIGHT AND OTHERWISE ARE HEREBY SPECIFICALLY RESERVED.

NOT TO BE USED FOR

CONSTRUCTION,

BIDDING,

RECORDATION,

CONVEYANCE, SALES,

OR AS THE BASIS FOR

THE ISSUANCE OF A

PERMIT

PRELIMINARY

SCALE: 1/4"=1'-0"

SCALE: 1/4"=1'-0"

1.

FA460822R0001

Attachment 13

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text

UNISEX 1

AutoCAD SHX Text

UNISEX 2

AutoCAD SHX Text

CORR. 1

AutoCAD SHX Text

MECH./ ELEC.

AutoCAD SHX Text

TELE./ COMM.

AutoCAD SHX Text

WAITING

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text

UNISEX 1

AutoCAD SHX Text

UNISEX 2

AutoCAD SHX Text

CORR. 1

AutoCAD SHX Text

MECH./ ELEC.

AutoCAD SHX Text

TELE./ COMM.

AutoCAD SHX Text

WAITING

AutoCAD SHX Text Drawing Number

AutoCAD SHX Text Facility Number

AutoCAD SHX Text Project Number

AutoCAD SHX Text

PROJECT TITLE

AutoCAD SHX Text

SHEET

AutoCAD SHX Text

SHEET TITLE

AutoCAD SHX Text

OF

AutoCAD SHX Text

REVISION

AutoCAD SHX Text

BY/DATE

AutoCAD SHX Text Designer

AutoCAD SHX Text Drafter

AutoCAD SHX Text Project Manager

AutoCAD SHX Text Date

AutoCAD SHX Text

DESIGN FIRM

AutoCAD SHX Text Engineer

AutoCAD SHX Text Pavements

AutoCAD SHX Text Engineer

AutoCAD SHX Text Corrosion

AutoCAD SHX Text Protective

AutoCAD SHX Text Engineer

AutoCAD SHX Text Coating Engr.

AutoCAD SHX Text Fire Chief

AutoCAD SHX Text Operations

AutoCAD SHX Text Chief of

AutoCAD SHX Text Construction

AutoCAD SHX Text Roofing

AutoCAD SHX Text Management

AutoCAD SHX Text

COORDINATION

AutoCAD SHX Text Computers

AutoCAD SHX Text Engineer

AutoCAD SHX Text Systems

AutoCAD SHX Text Security

AutoCAD SHX Text Police

AutoCAD SHX Text Security

AutoCAD SHX Text Bioenvironmental

AutoCAD SHX Text Airfield

AutoCAD SHX Text Safety

AutoCAD SHX Text Ground

AutoCAD SHX Text Manager

AutoCAD SHX Text Communication

AutoCAD SHX Text

APPROVED

AutoCAD SHX Text

SIGNATURE

AutoCAD SHX Text Chief of

AutoCAD SHX Text Engineering

AutoCAD SHX Text Design

AutoCAD SHX Text Chief of

AutoCAD SHX Text Contracting

AutoCAD SHX Text User

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text Engineer

AutoCAD SHX Text Civil

AutoCAD SHX Text Air Force Base

AutoCAD SHX Text Barksdale

AutoCAD SHX Text Louisiana

AutoCAD SHX Text

DESIGN FIRM

AutoCAD SHX Text

NOVEMBER 2018

AutoCAD SHX Text

RKC

AutoCAD SHX Text

DWB

AutoCAD SHX Text

DWB

AutoCAD SHX Text 3E

AutoCAD SHX Text

TITLE 1-A 15%%%

AutoCAD SHX Text

6 NOV 2018

AutoCAD SHX Text B1512

AutoCAD SHX Text

OPP. NO. 1072069

AutoCAD SHX Text

BARKSDALE AIR FORCE

AutoCAD SHX Text

BASE, LOUISIANA 71110

AutoCAD SHX Text

CONSTRUCT VCC EXPANSION

AutoCAD SHX Text

BUILDING 1512

AutoCAD SHX Text E1.1

AutoCAD SHX Text

ELECTRICAL PLANS

AutoCAD SHX Text

LIGHTING PLAN

AutoCAD SHX Text

POWER & SYSTEMS PLAN

%%UELECTRICAL NOTES%%U: