Attachment 10 - 556-402 Expand SPS - 100CD Equip Cut Sheets - Excerpt.pdf

100% CONSTRUCTION DOCUMENTS

EQUIPMENT CUT SHEETS

November 29, 2022 Revised 7-5-2023

Expand Sterile Processing Services

(SPS)

Capt. James A. Lovell Federal Health Care Center

3001 Green Bay Road, BLDG 133CA North Chicago, Illinois 60064-3048

VA Project #556-402 Alesia Project #2021-22

Equipment Cut Sheets

VHANCHLidD Text Box This is an excerpt of volumes 1 through 4 (indicated by "X") of files:

"556-402 SPS 100CD Equip Cut Sheets 29NOV22-r5JUL23 X-4.pdf".

This excerpt includes only cut sheets for Contractor Provided, Contractor Installed (CC) equipment; not all are listed.

The file does not include cut sheets of all equipment, regardless of which party is responsible for providing and installing.

See 100% CD Drawing sheet QH601 Equipment JSN Schedules. The drawings and specifications take precedence over information shown hererin.

(This page is left blank intentionally)

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Revised 11/16/16 Printed in U.S.A.

The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2016 by Bobrick Washroom Equipment, Inc.

Technical Data

7/8'' 22mmS

W

1-3/4'' 44mm

3-3/8'' 86mm

3/4'' Typ.

19mm

S 4-3/8'' 111mm

S

S

H2

1-5/16'' 33mm

R ec o m m en d ed

M o u n ti n g H ei g h t

O ff

F lo o r

-1

/2

5m m

Finish Face of Wall

Tumbler Lock

S

H1

TILT MIRROR WITH

STAINLESS STEEL FRAME

B-293

SERIES

MATERIALS:

Mirror Frame — 18-8, type 304, heavy-gauge stainless steel, 3/4" x 3/4" (19 x 19mm) angle with vertical-grain satin finish. One piece, roll-formed construction forms continuous integral stiffener on all sides. Bevel design on front of angle holds frame tightly against mirror. Corners of mirror frame are heliarc welded, ground and polish smooth. Galvanized steel back is fastened to frame with concealed screws and equipped with integral horizontal hanging brackets near the top and bottom of the mirror for hanging the mirror and to prevent the mirror from pulling away from the wall frame.

Wall Frame — 18-8, type 304, heavy-gauge stainless steel with satin finish. Tapers from 4-3/8" (111mm) depth at top to 1-5/16" (33mm) depth at bottom. Wall Frame furnished with tumbler lock to secure mirror to wall frame.

Designer's Note: Type 304 stainless steel provides superior corrosion resistance, compared to 400 Series stainless steel, against environmental moisture, hose-down maintenance and strong cleaning solutions.

Mirror — No. 1 quality, 1/4" (6mm) select float glass, selected for silvering; electrolytically copper-plated by the galvanic process, guaranteed for 15 years against silver spoilage. All edges are polished and protected by plastic filler strips; back is protected by full-size, shock-absorbing, water-resistant, nonabrasive, 1/8" (3mm) thick polystyrene padding.

OPERATION:

Mirror is designed to provide full visibility for wheelchair patients in hospitals and nursing homes.

INSTALLATION:

For complete installation instructions please follow 293-69 installation instruction sheet.

SPECIFICATION:

Tilt mirror assembly shall consist of a mirror and a separate wall frame with built-in wall hanger. Wall frame furnished with tumbler lock for securing mirror to wall frame. Tilt mirror frame shall be type 304 stainless steel with beveled front to hold frame tightly against mirror;

corners shall be welded, ground, and polished smooth. Wall frame shall be type 304 stainless steel designed with horizontal locking bars to secure mirror to wall frame. All exposed surfaces shall have satin finish with vertical grain. Select float glass mirror shall be guaranteed for 15 years against silver spoilage. All edges shall be protected by plastic filler strips. Back shall be protected by full-size, shock-absorbing, water-resistant, nonabrasive, 1/8" (3mm) thick polystyrene padding.

Tilt Mirror shall be Model B-293 _____________ (insert width and height) of Bobrick Washroom Equipment, Inc., Clifton Park, New York; Jackson, Tennessee; Los Angeles, California; Bobrick Washroom Equipment Company, Scarborough, Ontario;

Bobrick Washroom Equipment Pty. Ltd., Australia; and Bobrick Washroom Equipment Limited, United Kingdom.

STANDARD STOCK SIZES

W H1

MODEL

NO.

MIRROR SIZE

W H2

OVERALL SIZE

B-293 1830 18'' (46cm) 30'' (76cm) 18'' (46cm) 30-3/16'' (77cm) B-293 1836 18'' (46cm) 36'' (91cm) 18'' (46cm) 36-3/16'' (92cm) B-293 2436 24'' (61cm) 36'' (91cm) 24'' (61cm) 36-3/16'' (92cm)

Other sizes up to 40" x 40" (101 x 122cm) or 48" x 36" (122 x 91cm) are available on special order; minimum size available, 16" x 24" (41 x 61cm).

Design not as shown jpthurman Text Box A1067 jpthurman Highlight B-293 1836 18'' (46cm) 36'' (91cm) 18'' (46cm) 36-3/16'' (92cm) jpthurman Arrow jpthurman Cloud jpthurman Highlight 18-8, type 304, heavy-gauge stainless steel, jpthurman Highlight 18-8, type 304, heavy-gauge stainless steel with satin fnish jpthurman Highlight No. 1 quality, 1/4" (6mm) select foat glass jpthurman continued . . .

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Rev. 2/25/16 R/B Printed in U.S.A.

The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2016 by Bobrick Washroom Equipment, Inc.

Technical Data

2-1/2'' 65mm

S

1/2'' 13mm

Side View Back Plate/Wall Hanger

2-9/16'' 65mm

S

4'' or 5" Typ.

100 or 125mm

S T

2-1/16'' 50mm

S

1-13/16'' 45mm

S

3" 75mm

S

Locking Screw (Phillips-Head)

Frame

Mirror

1/2'' 13mm

Frame

Mirror Slide flat-blade screwdriver or Key between Mirror and Wall. Depress Tab on back Panel and remove Mirror.

Contact factory for key.

Lock Tab

4-5/8" 117mm

3-1/8" 79mm

Wall Bracket

Lock Tab

Mirror Key

Half Mirror Width

Frame

Mirror

S

S

Finish Face of Wall

3/4'' 19mm

3/4'' 19mm

2-1/2'' 65mm

S

2-9/16'' 65mm

S

4'' or 5" Typ.

100 or 125mm

S

Side View Back Plate/Wall Hanger

Frame

Mirror

Finish Face of Wall

B-290 1830 18'' (46cm) 30'' (76cm) B-290 1836 18'' (46cm) 36'' (91cm) B-290 2430 24'' (61cm) 30'' (76cm) B-290 2436 24'' (61cm) 36'' (91cm))

STANDARD B-290 SERIES MIRRORS

HW

MODEL

NO.

OVERALL SIZE

All Other Size Mirrors

B-290 2448 24'' (61cm) 48'' (122cm) B-290 2460 24'' (61cm) 60'' (152cm) B-290 2472 24'' (61cm) 72'' (183cm))

STANDARD B-290 SERIES MIRRORS

HW

MODEL

NO.

OVERALL SIZE

Width Hangers Up to 30'' (Up to 76cm) 1 31" to 41" (78 to 104cm) 2 42" to 72" (106 to 183cm) 3 73" to 91" (185 to 231cm) 4 92" to 116" (233 to 294cm) 5 117" to 144" (297 to 365cm) 6

GLASS MIRROR WITH

STAINLESS STEEL

ANGLE FRAME

MATERIALS:

Frame — 18-8, heavy-gauge stainless steel, 3/4" x 3/4" (19 x 19mm) angle with satin finish. One-piece, roll-formed construction forms continuous integral stiffener on all sides. Bevel design on front of angle holds frame tightly against mirror.

Corners of mirror frame are heliarc welded, ground and polish smooth. Galvanized steel back is fastened to frame with concealed screws and equipped with integral horizontal hanging brackets near the top and bottom of the mirror for hanging the mirror and to prevent the mirror from pulling away from the wall. Locking devices secure mirror to concealed wall hanger.

Designer's Notes:

1. Special-order sizes available on request.

2. Maximum size one-piece angle-frame mirror, 144'' x 72'' (366 x 183cm); minimum size, 12'' x 12'' (30 x 30cm).

Maximum frame size available, 180'' x 72'' (457 x 183cm) with two pieces of glass in one-piece frame. Stainless steel I-section with polished finish covers seam where two pieces of glass butt together.

3. All Bobrick framed mirrors are manufactured to overall width and height dimensions. EXAMPLE: A 24'' x 36'' (61 x 91cm) mirror will be furnished 24'' x 36'' (61 x 91cm) outside-of-frame to outside-of-frame.

4. To specify special sizes use Series Number followed by width then height in inches. EXAMPLE: B-290 2024.

5. Bobrick framed mirrors are manufactured to a tolerance ± 1/8'' (3.2mm).

6. For sufficient space to lift mirror onto wall hanger(s), provide 3-1/4'' (85mm) for Snap Locking Design; 5-3/8" (137mm) for Lock Tab Design minimum clearance above center line of mounting screw holes.

7. Provide 1'' (25mm) minimum clearance at bottom of mirror for unlocking mirror from wall and 1/2'' (12.7mm) clearance on each side.

B-290

SERIES

Snap Locking Design (Rear View)

Lock Tab Design (Rear View)

Figure: 1 Figure: 2

Note: Mirrors greater than 30" in width will have multiple hanger brackets with a typical 8" off each edge.

jpthurman Text Box A1080 jpthurman Highlight B-290 2472 24'' (61cm) 72'' (183cm)) jpthurman Rectangle jpthurman Arrow

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. B-290 Rev. 2/25/16 R/B Printed in U.S.A.

The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2016 by Bobrick Washroom Equipment, Inc.

Aprox. 1" 25mm Initial

Position

S

S

Final Position

CL

Aprox. 1"

25mm Initial Position

S

S

Final Position

CL

Lock Tab Design (Front View)

Snap Locking Design (Front View)

Figure: 3 Figure: 4

Mirror — No. 1 quality, 1/4" (6mm) select float glass (standard glass): selected for silvering, electrolytically copper-plated by the galvanic process, and guaranteed for 15 years against silver spoilage. All edges protected by plastic filler strips; back is protected by full-size, shock-absorbing, water-resistant, nonabrasive, 3/16" (5mm) thick polyethylene padding.

Concealed Wall Hanger — Galvanized steel construction. Incorporates upper and lower support members, which engage lower backplate louvers to keep bottom of mirror against wall

INSTALLATION:

Mount wall hanger on wall with screws (not furnished) at points indicated by an S. For plaster or dry wall construction, provide backing to comply with local building codes, then secure wall hanger with screws (not furnished). When providing a concealed backing, allow backing to cover range of mounting hole locations shown on drawing. For other wall surfaces, provide fiber plugs or expansion shields for use with screws (not furnished), or provide 1/8" (3mm) toggle bolts or expansion bolts. Hang mirror on wall hanger with all four backplate louvers engaged behind horizontal wall hanger members. To do this, mirror must be centered in front of the wall hanger horizontally, pressed flat against the wall approximately 1" (25mm) above final position and then lowered into final position.

Snap Locking Design — Locking devices automatically secure mirror to concealed wall hanger when it is lowered into final position (see figure 3). Locking devices may be unlocked by inserting two flat blade screwdrivers behind each side of mirror near the bottom or under the bottom of the mirror and pulling mirror bottom forward and then up.

Lock Tab Design — Locking devices automatically secure mirror to concealed wall hanger when it is lowered into final position (see figure 4). Locking device may be unlocked by sliding a flat-blade screwdriver or Key between mirror and wall at center of mirror and depressing tab on back panel. If key is required, please contact the factory.

SpEcIFIcATION:

Mirror shall have a one-piece, stainless steel angle frame, 3/4" x 3/4" (19 x 19mm) with continuous integral stiffener on all sides and beveled front to hold frame tightly against mirror; corners shall be heliarc welded, ground, and polished smooth;

all exposed surfaces shall have satin finish. Reflective surfaces shall be guaranteed for 15 years against silver spoilage. All edges shall be protected by plastic filler strips and the back shall be protected by full-size, shock-absorbing, water-resistant, nonabrasive, 3/16" (5mm) thick polyethylene padding. Galvanized steel back shall have integral horizontal hanging brackets located at top and bottom for mounting on concealed wall hanger and to prevent the mirror from pulling away from the wall.

Locking devices secure mirror to concealed wall hanger. Mirror shall be removable from wall hanger for reglazing mirror.

Framed Mirror shall be Model B-290 _______________ (insert width and height) of Bobrick Washroom Equipment, Inc., Clifton Park, New York; Jackson, Tennessee; Los Angeles, California; Bobrick Washroom Equipment Company, Scarborough, Ontario; Bobrick Washroom Equipment Pty. Ltd., Australia; and Bobrick Washroom Equipment Limited, United Kingdom.

jpthurman Text Box A1080 jpthurman

B-290 2472

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Revised 4/21/17 R/B Printed in U.S.A.

The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2017 by Bobrick Washroom Equipment, Inc.

Technical Data

MIRROR WITH

STAINLESS STEEL

ANGLE FRAME

AND SHELF

Designer's Notes:

1 Special-order sizes available on request.

2. Maximum size one-piece angle-frame mirror, 96'' x 72'' (244 x 183cm); minimum size, 12" x 12" (30 x 30cm).

3. All Bobrick framed mirror/shelf models are manufactured to overall width and height dimensions of mirror, not including shelf. EXAMPLE: For Lock Tab Design B-292 2436 (61 x 95cm) mirror will be furnished 24'' x 37-1/4'' (61 x 94cm) outside-of-frame to outside-of-frame including shelf.

4. To specify special sizes use Series Number followed by width x height in inches. EXAMPLE: B-292 2024 20" x 24" (51 x. 61cm).

5. Bobrick framed mirror/shelf models are manufactured to a tolerance ± 1/8'' (3.2mm).

6. For sufficient space to lift mirror onto wall hanger(s), provide 1" (25mm) minimum clearance above top of mirror frame.

7. Provide 1'' (25mm) minimum clearance at bottom of mirror for unlocking mirror from wall and 1/2'' (12.7mm) clearance on each side.

Figure: 1

B-292

SERIES

Snap Locking Design (Rear View)

Lock Tab Design (Rear View)

Figure: 2

Note: Mirrors greater than 30" in width will have multiple hanger brackets with a typical 8" off each edge.

All Other Size Mirrors

Width Hangers

Up to 30'' (Up to 76cm) 1 31" to 41" (78 to 104cm) 2 42" to 72" (106 to 183cm) 3 73" to 91" (185 to 231cm) 4 92" to 96" (233 to 249cm) 5

MODEL

NO.

STANDARD B-292 SERIES MIRRORS

OVERALL SIZE

W H

B-292 1830 18'' (46cm) 30'' (76cm) B-292 1836 18'' (46cm) 36'' (91cm) B-292 2436 24'' (61cm) 36'' (91cm)

3/4'' 19mm

5'' 127mm

3/4'' 19mm

2-1/2'' 65mm

S

2-9/16'' 65mm

S

4'' or 5" Typ.

100 or 125mm

S

Side View Back Plate/Wall Hanger

Frame

Mirror

Finish Face of Wall

Slide flat-blade screwdriver or Key between Mirror and Wall. Depress Tab on back Panel and remove Mirror.

Contact factory for key.

Lock Tab

4-5/8" 117mm

3-1/8" 79mm

Wall Bracket

Lock Tab

Mirror Key

Half Mirror Width

3/4'' 19mm

Frame

Mirror

5-3/4'' 146mm

1-1/4'' 32mm

S

S

1/2'' 13mm

Finish Face of Wall jpthurman Text Box A1090 jpthurman Highlight B-292 1836 18'' (46cm) 36'' (91cm) jpthurman Rectangle

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. B-292 Rev. 4/21/17 R/B Printed in U.S.A.

The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2017 by Bobrick Washroom Equipment, Inc.

MATERIALS:

Frame — 18-8, type 304, heavy-gauge stainless steel, 3/4" x 3/4" (19 x 19mm) angle with satin finish. One-piece, roll-formed construction forms continuous integral stiffener on all sides. Bevel design on front of angle holds frame tightly against mirror. Corners of mirror frame are heliarc welded, ground, and polished smooth. Galvanized steel back is fastened to frame with concealed screws and equipped with integral horizontal hanging brackets near the top for hanging the mirror and near the bottom to prevent the mirror from pulling away from the wall. Locking devices secure mirror to concealed wall hanger.

Shelf — 18-8, type 304, 18-gauge (1.2mm) stainless steel with satin finish, 3/4" (19mm) return edge on front. Front and side return edges hemmed for additional strength and safety. Front corners of shelf are welded, ground, and polished smooth. Shelf is welded to mirror frame. No exposed rivet-heads, screws, or fasteners of any type on frame or shelf.

Mirror — No. 1 quality, 1/4" (6mm) select float glass (standard glass): selected for silvering, electrolytically copper-plated by the galvanic process, and guaranteed for 15 years against silver spoilage. All edges protected by plastic filler strips; back is protected by full-size, shock-absorbing, water-resistant, nonabrasive, 3/16" (5mm) thick polyethylene padding.

Concealed Wall Hanger — 16 gauge cold roll steel construction. Incorporates upper and lower support members, which engage backplate louvers to keep mirror against wall.

INSTALLATION:

Mount wall hanger on wall with screws (not furnished) at points indicated by an S. For plaster or dry wall construction, provide backing to comply with local building codes, then secure wall hanger with screws (not furnished). When providing a concealed backing, allow backing to cover minimum range of mounting hole locations shown on drawing. For other wall surfaces, provide fiber plugs or expansion shields for use with screws (not furnished), or provide 1/8" (3mm) toggle bolts or expansion bolts.

Hang mirror on wall hanger with all four backplate louvers engaged behind horizontal wall hanger members. To do this, mirror must be centered in front of the wall hanger horizontally, pressed flat against the wall approximately 1" (25mm) above final position and then lowered into final position.

Snap Locking Design — Locking devices automatically secure mirror to concealed wall hanger when it is lowered into final position (see figure 3). Locking devices may be unlocked by inserting two flat blade screwdrivers behind each side of mirror near the bottom or under the bottom of the mirror and pulling mirror bottom forward and then up.

Lock Tab Design — Locking devices automatically secure mirror to concealed wall hanger when it is lowered into final position (see figure 4). Locking device may be unlocked by sliding a flat-blade screwdriver or Key between mirror and wall at center of mirror and depressing tab on back panel. If key is required, please contact the factory.

SPECIFICATION:

Mirror shall have a one-piece, type 304 stainless steel angle frame, 3/4" x 3/4" (19 x 19mm) with continuous integral stiffener on all sides and beveled front to hold frame tightly against mirror; corners shall be heliarc welded, ground, and polished smooth; all exposed surfaces shall have satin finish. Shelf shall be type 304, 18-gauge (0.8mm) stainless steel with satin finish.

Shelf shall have a 3/4" (19mm) return edge on front. Front and side return edges hemmed and corners welded, ground, and polished smooth. Shelf shall be welded to mirror frame. No rivet-heads, screws, or fasteners of any type shall be exposed on frame or shelf. Select float glass mirror shall be guaranteed for 15 years against silver spoilage. All edges shall be protected by plastic filler strips and the back shall be protected by full-size, shock-absorbing, water-resistant, nonabrasive, 3/16" (5mm) thick polyethylene padding. Galvanized steel back shall have integral horizontal hanging brackets located at top and bottom for mounting on concealed wall hanger and to prevent the bottom of the mirror from pulling away from the wall. Locking devices secure mirror to concealed wall hanger. Mirror shall be removable from wall hanger for reglazing mirror.

Framed Mirror With Shelf shall be Model B-292 _______________ (insert width and height) of Bobrick Washroom Equipment, Inc., Clifton Park, New York; Jackson, Tennessee; Los Angeles, California; Bobrick Washroom Equipment Company, Scarborough, Ontario; Bobrick Washroom Equipment Pty. Ltd., Australia; and Bobrick Washroom Equipment Limited, United Kingdom.

Figure: 3 Figure: 4

Snap Locking Design (Front View)

Lock Tab Design (Front View)

Aprox. 1" 25mm Initial

Position

S

S

Final Position

CL

Aprox. 1"

25mm Initial Position

S

S

Final Position

CL

jpthurman Text Box A1090 jpthurman

B-292 1836

One Integrated Approach to Healthcare.

Sterile Processing Services

AMSCO Reprocessing Sinks’ innovative designs promote best practices

– delivering an improved process, a streamlined workflow and consistent outcomes.

AMSCO® 30, 50 and 70 Series Reprocessing Sinks

COMPLIANT & CONSISTENT

FROM THE START

Meeting the evolving standards of healthcare does not have to mean compromising efficiency or complicating processes.

jpthurman

A1195

Give yourself enough room to properly clean large devices without damage with 30” bays**

Larger Bays

Make every drop of chemistry count through the AMSCO 70 Series Reprocessing Sink’s integrated temperature monitoring and automated dosing. Get peak performance from enzymatics and ensure the precise dose is delivered… every time.*

*Based on Regular PMs & Calibration Schedules **AMSCO 50 and 30 Series Reprocessing Sinks only

Manual cleaning can be one of the most cumbersome and variable steps in reprocessing. Helping to ensure you maintain compliance both through process and audit, the AMSCO Reprocessing Sinks make meeting the current ANSI/AAMI standards* seamless.

Start driving best practices from the beginning

COMPLIANCE

Automated Degas Cycle

Documentation

ANSI/AAMI

COMPLIANT

ST79

Encourages best practice after the manual washing process for consistent performance of ultrasonic activity

Temperature Monitoring and Automated Dosing jpthurman

Instilling confidence, accuracy and safety, AMSCO Reprocessing Sinks help your CSSD run efficiently - allowing staff to focus on the critical step of manually cleaning instruments.

CONSISTENCY THAT

OPTIMIZES WORKFLOW

Making every space count – FlexPlates allow technicians to expand the surface area of their workspace

Maximizes Space

Counter height adjusts from 33-41”

Magnetized backsplash allows for organization and accessibility-allowing for placement anywhere on the backsplash - convenient for each technician

Convenient & Organized

Meeting the ergonomic challenges of a diverse workforce, and helping reduce the risk of work related injuries, the height adjustment feature makes the AMSCO 50 and 70 Series Reprocessing Sinks the ideal workstation.

Ergonomic

The intuitive icon-driven interface of the AMSCO 70 Series Reprocessing Sink provides confirmation of the current step being performed – while still allowing the flexibility to use other bays.

Ease of Use jpthurman

AMSCO 50 Reprocessing Sink

AMSCO 30 and 50 Series Reprocessing Sinks

BIG PERFORMANCE, BIG VALUE

SKU Length Number of Bays

SINK3077 77" 2

SINK3096 96" 2

SINK3097 97.5" 3

SINK30106 106" 3

SINK30120 120" 3

SKU Length Number of Bays

SINK5077 77" 2

SINK5096 96" 2

SINK5097 97.5" 3

SINK50106 106" 3

SINK50120 120" 3

AMSCO 30 Reprocessing Sink AMSCO 50 Reprocessing Sink

The AMSCO 70 Series Reprocessing Sink can be configured to help comply with the latest standards while meeting your space, volume and budget demands.

AMSCO 70 Series Reprocessing Sink

SOLUTIONS TO FIT YOUR

WORKFLOW

Dual Bay

SKU Length Right to Left Workflow

SW01201 80" Wash, Aqua Klenz

SW01402 80" Rinse, Wash

SW01302 80" Sonic Klenz, Wash

SW02201 94" Wash, Aqua Klenz

SW02402 94" Rinse, Wash

SW02302 94" Sonic Klenz, Wash

SKU Length Left to Right Workflow

SW01102 80" Aqua Klenz, Wash

SW01204 80" Wash, Rinse

SW01203 80" Wash, Sonic Klenz

SW02102 94" Aqua Klenz, Wash

SW02204 94" Wash, Rinse

SW02203 94" Wash, Sonic Klenz

SKU Length Right to Left Workflow

SW03421 106" Rinse, Wash, Aqua Klenz

SW03422 106" Rinse, Wash, Wash

SW03342 106" Sonic Klenz, Rinse, Wash

SW04421 120" Rinse, Wash, Aqua Klenz

SW04422 120" Rinse, Wash, Wash

SW04342 120" Sonic Klenz, Rinse, Wash

Triple Bay

SKU Length Left to Right Workflow

SW03124 106" Aqua Klenz, Wash, Rinse

SW03224 106" Wash, Wash, Rinse

SW03243 106" Wash, Rinse, Sonic Klenz

SW04124 120" Aqua Klenz, Wash, Rinse

SW04224 120" Wash, Wash, Rinse

SW04243 120" Wash, Rinse, Sonic Klenz jpthurman Text Box A1195 jpthurman Cloud jpthurman Line jpthurman Line jpthurman Line

Line

M9466EN.2018-04 Rev. A ©2018 STERIS Corporation.

All rights reserved.

For more information please contact your STERIS representative or visit STERIS.com/DecontaminationSinks

SINK FEATURES COMPARISON

Temperature Monitoring

Automated Chemistry

Dosing

Sonic Klenz Bay

Flex Plates

Electric Height

Adjustment

Magnetic Back

Splash

30" Bays

Air Pistol

Water Pistol

Etched Gallon

Markings AMSCO 70 Series Reprocessing Sink

X X X X X X X X X

AMSCO 50 Series Reprocessing Sink

Optional X X X X X X

AMSCO 30 Series Reprocessing Sink

Optional X X X X X jpthurman

900 Clary Connector, Eastanollee, GA 30538 Tel: (706) 827-2720 / Fax (706) 827-2710 www.asi-storage.com

HARDWOOD BENCH TOP SPECIFICATIONS

Date Issued 01-17

SPECIFICATIONS

Benches shall be hardwood. All corners shall be rounded and sanded. All surfaces shall be fi nished with two coats of clear lacquer. Pedestals shall be spaced no more than 60” apart.

LENGTH

9 1/2" 12" 24"

NA

WIDTH

(Standard Sizes)

NA

NA

NA

jpthurman Text Box A5020 jpthurman Highlight 9 1/2" jpthurman Highlight jpthurman Text Box X jpthurman Arrow

900 Clary Connector, Eastanollee, GA 30538 Tel: (706) 827-2720 / Fax (706) 827-2710 www.asi-storage.com

TRAPEZOID PEDESTAL SPECIFICATIONS

Date Issued 01-17

SPECIFICATION

Pedestal shall be 2” diameter, 16 gauge brushed stainless steel formed into the shape of a trapezoid. The bo om shall be 14 inches wide with four (4) moun ng holes. The pedestal shall be 16-1/4” high. The top fl ange shall have four (4) holes for fastening to the bench. The bench can be moveable or anchored.

(Floor anchors provided by installer) jpthurman Text Box A5020 jpthurman Rectangle

900 Clary Connector, Eastanollee, GA 30538 Tel: (706) 827-2720 / Fax (706) 827-2710 www.asi-storage.com

TUBE PEDESTAL SPECIFICATIONS

Date Issued 04-21

SPECIFICATION

Pedestal shall be 1-1/2” diameter steel tubing with 11 gauge steel fllanges welded to each end. The b o om and top flange shall be 8” in diameter with three (3) holes for anchoring in each flange. The pedestal shall be 16-1/4” high and shall be powder coated to match lockers.

(Floor anchors provided by installer) jpthurman

A5020

900 Clary Connector, Eastanollee, GA 30538 Tel: (706) 827-2720 / Fax (706) 827-2710 www.asi-storage.com

WOOD INSTRUCTIONS

PEDESTAL & BENCH TOP

Date Issued 02-21

PEDESTAL AND BENCH TOP

INSTALLATION INSTRUCTIONS

GENERAL INSTRUCTIONS

1. Check all material against packing slip to be sure it is correct and free from damage.

2. Iden fy all parts as they are unpacked

3. Please read all instruc ons prior to assembly.

4. Use correct hardware as specified in the assembly instruc ons.

CAUTION

Handle all components carefully when assembling benches. Install all benches plumb and ghten all hardware securely. Retain instruc ons for future reference.

jpthurman

900 Clary Connector, Eastanollee, GA 30538 Tel: (706) 827-2720 / Fax (706) 827-2710 www.asi-storage.com

16 gauge stainless steel

10 gauge tubular steel

Shim as required to level bench tops

GENERAL ASSEMBLY FOR PEDESTALS

Using the pedestal as a template, locate centers. Drill pilot holes and a ached pedestals to bench with the screws provided. Floor anchors to be provided by the installer.

Note: 3/16” drill is recommended for pilot holes

(4) 1/4” X 3/4” Lag Screw (3) 1/4” X 3/4” Lag Screw jpthurman Text Box A5020 jpthurman

900 Clary Connector, Eastanollee, GA 30538 Tel: (706) 827-2720 / Fax (706) 827-2710 www.asi-storage.com

24” wide benches shall have (2) steel pedestals at each support point..

*Bench pedestals shall be spaced no more than 60” O.C. .

jpthurman

900 Clary Connector, Eastanollee, GA 30538 Tel: (706) 827-2720 / Fax (706) 827-2710 www.asi-storage.com

SPECIFICATIONS

Wooden bench tops shall be constructed of 1-1/4” thick hardwood. Bench tops shall have a smooth finish. Edges shall be slightly rounded. Pedestals shall be spaced no more than 60”apart O.C.

LENGTH

9 1/2" 12" 24"

NA

WIDTH

(Standard Sizes)

NA

NA

NA

jpthurman Text Box A5020 jpthurman Highlight 9 1/2" jpthurman Highlight jpthurman Text Box X jpthurman Arrow

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Revised 4/09 Series E Printed in U.S.A.

The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2009 by Bobrick Washroom Equipment, Inc.

Technical Data

Shower Seat in Reversed Position

33'' 840mm

19-1/2'' 495mm

16-1/2'' 420mm

6-3/4'' 170mm

13-3/8'' 340mm

14-7/16'' 365mm

Bolts Removed and Replaced to Reverse Seat Position

2-1/4'' 55mm Dia.

Bolt Circle

S S

S

1-1/8'' 30mm

S S

S S

2-1/4'' 55mm

S S

20-15/16'' 530mm

Universal/Barrier-Free Recommended

Mounting Height *17'' to 19''

430 to 485mm

Finish Face of Floor

Support Tube

Baseplate with Spring

Guide Bracket S

S S

S

Mounting Flanges (2)

1-3/8'' 35mm

Finish Face of Wall

5-1/2'' 140mm

22-5/16'' 565mm

21-7/8'' 555mm

4-1/2'' 115mm

Concealed wall backing to comply with local building codes, not furnished by Bobrick.

9-3/8'' 240mm

7-1/4'' 185mm

S

*Consult local building codes

17-5/16'' 440mm

MATERIALS:

Seat — One-piece, 1/2" (13mm) thick, solid phenolic with matte-finish, ivory-colored, melamine surfaces and black phenolic-resin core — cannot delaminate. Integral slots for water drainage. Secured to frame with stainless steel carriage bolts and acorn nuts. Reversible for left- or right-hand installation in the field.

Frame — 18-8 S, type-304, stainless steel with satin finish. 16-gauge (1.6mm), 1-1/4" (30mm) square tubing and 18-gauge (1.2mm), 1" (25mm) diameter seamless tubing.

Mounting Flanges (2) — 18-8 S, type-304, 3/16" (5mm) thick stainless steel with satin finish. 3" (75mm) diameter with three mounting screw holes.

Baseplate — 18-8 S, type-304, heavy-gauge stainless steel.

Spring — 17-7, type-301, 24-gauge (0.6mm) stainless steel. Spot-welded to baseplate.

Guide Bracket — 18-8 S, type-304, 16-gauge (1.6mm) stainless steel with satin finish.

Left-Hand Seat Shown

REvERSIbLE SOLID phEnOLIc

FOLDInG ShOWER SEAT b-5181 jpthurman

A5030

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. B-5181 S/E Rev.4/09 Printed in U.S.A.

The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2009 by Bobrick Washroom Equipment, Inc.

OpERATIOn:

Shower seat folds up against wall when not in use. The spring at the top of the baseplate holds seat in upright position until released by pulling the top of the seat away from the wall. Mounting flanges and guide bracket allow for varying mounting heights and leave the floor clear for easy cleaning. Nonporous solid phenolic seat has slots to permit water to drain, does not splinter or require oiling, and will not support growth of bacteria. Slotless round-head carriage bolts and acorn nuts provide additional safety to user. Bobrick shower seats, when properly installed, have sufficient strength to support 360 lbs., (163 kg) complying with barrier-free accessibility guidelines (including ADAAG in the U.S.A.).

InSTALLATIOn:

Installation to Wall. Secure unit to wall at points indicated by an S, with the two mounting flanges located at top and the baseplate and guide bracket below. The bottom of the support tube must be positioned within the baseplate and guide bracket before they are secured to wall. Mounting height of shower seat must comply with local building codes.

For stud walls, provide concealed backing to comply with local building codes and secure with #14 x 2-1/2" (6.3 x 65mm) stainless steel sheet-metal screws furnished by manufacturer.

For prefabricated shower stalls, provided adequate backing by the shower stall manufacturer. Secure with #14 x 2-1/2" (6.3 x 65mm) stainless steel mounting screws furnished by manufacturer.

For masonry walls, provide fiber plugs or expansion shields for use with furnished screws, or provide 1/4" (6mm) toggle bolts or expansion bolts.

Caution: These shower seats are no stronger than the anchors and walls to which they are attached and, therefore, must be firmly secured in order to support the loads for which they are intended. Consult and comply with local building codes.

How to Reverse Shower Seat. The solid phenolic shower seat surface may be positioned on the stainless steel frame with the longer 20-15/16" (530mm) side on the left or right. The repositioning of the shower seat surface may be done on the frame before installation on the wall, or after the unit has been installed.

If repositioning the seat surface before installation of the unit on the wall; place entire unit on a horizontal surface; remove carriage bolts and acorn nuts (4); turn seat over reversing position of long and short ends; reinstall carriage bolts and acorn nuts.

If repositioning the seat surface after the unit has been installed on the wall; lower folding seat to horizontal position; remove carriage bolts and acorn nuts (4); turn seat over reversing position of long and short ends; reinstall carriage bolts and acorn nuts.

Important Notes: Support square frame tubes when loosening and removing carriage bolts and acorn nuts; the square frame tubes may separate from the round tubes that support the solid phenolic shower seat. If square and round frame tubes come apart when solid phenolic shower seat is removed, reassemble by placing round frame tube ends in the round holes on the sides of the square frame tubes.

SpEcIFIcATIOn:

Reversible folding shower seat shall have a frame constructed of type-304, satin-finish stainless steel that consists of 16-gauge (1.6mm), 1-1/4'' (30mm) square tubing and 18-gauge (1.2mm), 1'' (25mm) diameter seamless tubing. Seat shall be one-piece, 1/2" (13mm) thick, solid phenolic with matte-finish, ivory-colored, melamine surfaces, and black phenolic-resin core; secured to frame with stainless steel carriage bolts and acorn nuts. Seat shall be reversible for left- or right-hand installation in the field.

Shower seat shall be equipped with two 3'' (75mm) diameter mounting flanges constructed of type-304, 3/16'' (5mm) thick, satin-finish stainless steel; a guide bracket constructed of type-304, 16-gauge (1.6mm), satin-finish stainless steel; and a spring constructed of type-301, 24-gauge (0.6mm) stainless steel that is spot-welded to a baseplate of type-304, heavy-gauge stainless steel. Seat shall remain in upright position when not in use. Shower seat shall comply with barrier-free accessibility guidelines (including ADAAG in the U.S.A.). Manufacturer's service and parts manual shall be provided to the building owner/manager upon request.

Reversible Folding Shower Seat shall be Model B-5181 of Bobrick Washroom Equipment, Inc., Clifton Park, New York; Jackson, Tennessee; Los Angeles, California; Bobrick Washroom Equipment Company, Scarborough, Ontario; Bobrick Washroom Equipment Pty. Ltd., Australia; and Bobrick Washroom Equipment Limited, United Kingdom.

jpthurman

A5030

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. B-262 r06/30/15 Printed in U.S.A.

The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2015 by Bobrick Washroom Equipment, Inc.

Technical Data

S

10-13/16" 275mm

7-1/2" 190mm

Lock & Key

Door S

S

S

3-15/16" 100mm

Finish Face of Wall

14-1/16" 355mm

R ec o m m en d ed

M o u n ti n g H ei g h t

O ff

F lo o r to

0" to

0m m

R ec o m m en d ed

M o u n ti n g H ei g h t

O ff

F lo o r

F o r A cc es si b le D es ig n

0m m10-7/16"

265mm

S S

MATERIALS:

Cabinet — 18-8, type-304, 22-gauge (0.8mm) stainless steel. All-welded construction. Exposed surfaces have satin finish. Towel tray has hemmed opening to dispense paper towels without tearing.

Door — 18-8, type-304, 22-gauge (0.8mm) stainless steel with satin finish. Secured to cabinet with a full-length stainless steel piano-hinge. Equipped with a tumbler lock keyed like other Bobrick washroom accessories.

Optional: Order Bobrick Part No. 262-130 TowelMate® available as an optional accessory. TowelMate accessory allows for paper towels to dispense one at a time without bulging, sagging or falling through the towel tray opening. TowelMate fits Gamco and most manufacturers' similar models.

OPERATION:

Unit dispenses C-fold and multifold paper towels 3-1/8" to 3-13/16" (79–97mm) deep. Slots in sides of cabinet indicate refill time. Capacity: 400 C-fold or 525 multifold paper towels. To dispense narrower towels 2-1/2" to 3-1/8" (64–79mm) deep, order optional TowelMate accessory Bobrick Part No. 262-130.

INSTALLATION:

Mount unit on wall with four #10 x 1-1/4" (4.8 x 32mm) sheet-metal screws (not furnished) at four of the eight mounting holes indicated by an S (top slots and bottom holes preferable). For plaster or dry wall construction, provide concealed backing to comply with local building codes, then secure with sheet-metal screws. For other wall surfaces, provide fiber plugs or expansion shields for use with sheet-metal screws, or provide 1/8" (3mm) toggle bolts or expansion bolts.

SPECIFICATION:

Surface-mounted paper towel dispenser shall be type-304 stainless steel with all-welded construction; exposed surfaces shall have satin finish. Door shall be secured to cabinet with a full-length stainless steel piano-hinge and equipped with a tumbler lock keyed like other Bobrick washroom accessories. Paper towel tray shall have hemmed opening to dispense paper towels without tearing. Unit shall be capable of dispensing 400 C-fold or 525 multifold paper towels measuring 3-1/8" to 3-13/16" (79 to 97mm) deep. Narrower paper towels 2-1/2" to 3-1/8" (65 to 79mm) deep may be efficiently dispensed with the use of an optional TowelMate accessory, Bobrick Part No. 262-130. TowelMate accessory allows for paper towels to dispense one at a time without bulging, sagging or falling through the towel tray opening.

Surface-Mounted Paper Towel Dispenser shall be Model B-262 of Bobrick Washroom Equipment, Inc., Clifton Park, New York; Jackson, Tennessee; Los Angeles, California; Bobrick Washroom Equipment Company, Scarborough, Ontario; Bobrick Washroom Equipment Pty. Ltd., Australia; and Bobrick Washroom Equipment Limited, United Kingdom.

ClassicSeries®

SURFACE-MOUNTED

PAPER TOWEL DISPENSER

B-262 jpthurman Text Box A5080 jpthurman Highlight Surface-mounted paper towel dispenser shall be type-304 stainless steel with all-welded construction; exposed surfaces shall have satin fnish.

Electronic Hands Free Roll Towel Dispenser

Product Overview

The TD0245 Electronic Touchless Roll Towel Dispenser provides maximum options and cost reduction. It features adjustable paper lengths (9", 12", 15") and time delay (1, 2, 3 seconds).

Model TD0246 comes equipped with an AC/DC Adaptor plug.

Product Features:

• Automatic, hygienic, hands-free operation

• Paper is fully protected until the user is ready

• Patented paper savings mode reduces paper consumption by 12-15%

• Easy to install paper, batteries and change settings

• Auto-transfer system prevents stub roll waste

• Low battery indicator light

• Longest battery life in the industry with up to 72,000 cycles, or 1 year

• Optional AC/DC Adaptors available

(#SP012400)

Specifications:

More information and images available online.

PALMER FIXTURE | 800-558-8678 | INFO@PALMERFIXTURE.COM

MODEL # COLOR

TD0245-01 DARK TRANSLUCENT

TD0245-02 BLACK TRANSLUCENT

TD0245-03 WHITE TRANSLUCENT

TD0246-02 BLACK TRANSLUCENT

TOUCHLESS ROLL TOWEL DISPENSER | TD0245

Dimensions (in) 12.27”w x 15.20”h x 9.47”d

Weight (lb) 4.60 lb

Key Type 1

Batteries 4x “D” LR20 Alkaline

Capacity 8”W x 8”D Roll Towel

Case Pack 1 (1.14’³)

Pallet Qty 81 units jpthurman Text Box A5082 jpthurman Cloud

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Revised 10/18/13 Printed in U.S.A.

The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2013 by Bobrick Washroom Equipment, Inc.

Technical Data

Finish Face of Wall

S

1-11/16'' 45mm Typ.

R ec o m m en d ed

M o u n ti n g H ei g h t

O ff

F lo o r

F o r U n iv er sa l / A cc es si b le D es ig n

0'

0m m

3-13/16'' 95mm

7-1/2'' 190mm

Hinged Lid

1-11/16'' 45mm Typ.

S

10'' 255mm

ConturaSeries®

SURFACE-MOUNTED

SANITARY NAPKIN DISPOSAL

MATERIALS:

Container — 18-8, type-304, 22-gauge (0.8mm) stainless steel. All-welded construction. Exposed surfaces have satin finish.

Integral finger depression for opening cover. Front of container has same degree of arc as front of cover and other Bobrick ConturaSeries washroom accessories. Radius on side edges of container match corners and edges of cover and other ConturaSeries accessories.

Cover — 18-8, type-304, 22-gauge (0.8mm) stainless steel with satin finish. Drawn, one-piece, seamless construction. Front of cover has same degree of arc as front of container and other Bobrick Contura Series washroom accessories. Radius on corners and edges of cover match side edges of container and other Contura Series accessories. Secured to container with a full-length stainless steel piano-hinge.

OPERATION:

Cover flips up for disposal of sanitary napkins and for servicing container.

INSTALLATION:

For partitions with particle-board or other solid core, secure with two #8 x 3/4'' (4.2 x 19mm) sheet-metal screws (not furnished) at all points indicated by an S, or provide through-bolts, nuts, and washers.

For hollow-core metal partitions, provide solid backing into which sheet-metal screws can be secured. If two units are installed back-to-back, then provide threaded sleeves and machine screws for the full thickness of partition.

For masonry walls, provide fiber plugs or expansion shields for use with sheet-metal screws, or provide 3/16" (5mm) toggle bolts or expansion bolts.

For plaster or dry wall construction, provide concealed backing to comply with local building codes, then secure unit with sheet-metal screws.

SPECIFICATION:

Surface-mounted sanitary napkin disposal shall be type-304 stainless steel with all-welded construction; exposed surfaces shall have satin finish. Front of sanitary napkin disposal shall have same degree of arc and match other Bobrick ConturaSeries accessories in the washroom. Radius on corners and edges of sanitary napkin disposal shall complement other Bobrick ConturaSeries washroom accessories. Cover shall be drawn, one-piece, seamless construction and secured to container with a full-length stainless steel piano-hinge. Container shall have integral finger depression for opening cover.

Surface-Mounted Sanitary Napkin Disposal shall be Model B-270 of Bobrick Washroom Equipment, Inc., Clifton Park, New York; Jackson, Tennessee; Los Angeles, California; Bobrick Washroom Equipment Company, Scarborough, Ontario; Bobrick Washroom Equipment Pty. Ltd., Australia; and Bobrick Washroom Equipment Limited, United Kingdom.

B-270 jpthurman Text Box A5090 jpthurman Highlight Surface-mounted sanitary napkin disposal shall be type-304 stainless steel with all-welded construction; exposed surfaces shall have satin fnish

Home > All Products > Gloves > Latex Gloves > Glove Dispensers

More Images

Gloves stay within easy reach.

Attractive, clear, matches any decor.

Holds three boxes of gloves.

Mount to wall or place on counter.

Glove Dispenser - Triple Acrylic

MODEL

NO.

STYLE HOLDS NO.

OF BOXES

SIZE

W x H x D

PRICE EACH ADD TO

CART1 4+

H-1648 Acrylic 3 11 x 15 x 4" $42 $39 1 ADD

ULINE 1-800-295-5510

My Account | Contact Us | Sign In |

CareersProducts Uline Products Quick Order Catalog Request Special Offers About Us

Cart $0.00

GOSearch

Additional Info Email Page Add to Favorites Request a Catalog

A5107

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Rev. 9/1/17S/B Printed in U.S.A.

The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2017 by Bobrick Washroom Equipment, Inc.

Technical Data

L

L

Edge of Flange to Wall

36'' 915mm

4'' 100mm

39-3/4'' 1010mm 57-3/4''

1465mm

50'' 1270mm

Edge of Flange to Wall

Edge of Flange to Wall

32'' 815mm

4'' 100mm

39-3/4'' 1010mm

27-3/4'' 705mm

24'' 510mm

Edge of Flange to Wall continued . . .

42'' 1065mm

4'' 100mm

50'' 1270mm

57-3/4'' 1465mm

45-3/4'' 1160mm

Edge of Flange to Wall

Edge of Flange to Wall

2'' 50mm

2-1/4'' 55mm

3-1/8'' 80mm

5/16'' 8mm

Snap Flange Cover

3-1/4'' 85mm Dia.

1-1/2'' 38mm

End Mounting Flange

3-1/8'' 80mm

Intermediate Flange

2-5/8'' 65mm

2-1/4'' 55mm

3-1/8'' 80mm

1¼" (32mm) DIAMETER

STAINLESS STEEL GRAB BARS

WITH SNAP FLANGE

B-5806

SERIES

Satin finish Satin finish with peened gripping surface; add suffix .99 to model number

Specify Finish Required:

HORIZONTAL VERTICAL

B-5806 x 18, 24, 30, 36, 42, 48

TWO-WALL

TUB / SHOWER

COMPARTMENT BAR

B-5837

HORIZONTAL

TUB / SHOWER

COMPARTMENT BAR 24 x 36

B-58616

TWO-WALL

TOILET COMPARTMENT BAR 42 x 54

B-5897 jpthurman Text Box A5109 jpthurman Highlight Satin fnish with peened gripping surface; add suffx .99 to model number jpthurman Rectangle jpthurman Arrow jpthurman Rectangle jpthurman Callout Refer to drawings jpthurman Highlight jpthurman Highlight B-5806 jpthurman Arrow jpthurman Highlight

HORIZONTAL

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. B-5806 r8/31/17S/B Printed in U.S.A.

The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2017 by Bobrick Washroom Equipment, Inc.

MATERIALS:

Grab Bar — 18-8, type-304, 18-gauge (1.2mm) stainless steel tubing with satin-finish. 1-1/4" (32mm) outside diameter. Ends are heliarc welded to concealed mounting flanges. Clearance between the grab bar and wall is 1-1/2" (38mm).

Concealed Mounting Flanges — 18-8, type-304, 11-gauge (3.2mm) thick, stainless steel plate; end flanges 2" x 3-1/8" (50 x 80mm) with holes for attachment to wall. Intermediate flanges 2-5/8" x 3-1/8" (65 x 80mm) wide x 3-1/8" (80mm) diameter.

Snap Flange Covers — 18-8, type-304, 22-gauge (0.8mm) drawn stainless steel with satin-finish. 3-1/4" (85mm) diameter x 5/8" (16mm) deep. Each cover snaps over mounting flange to conceal mounting screws.

STRENGTH:

Bobrick grab bars that provide 1-1/2" (38mm) clearance from wall can support loads in excess of 900 pounds (408kg) if properly installed. Other grab bar configurations can support loads in excess of 250 pounds (113kg) if properly installed, complying with accessible design (including ADAAG in the U.S.A.) for structural strength.

Safety Warning: Grab bars are no stronger than the anchors and walls to which they are attached and, therefore, must be firmly secured in order to support the loads for which they are intended. To avoid potential injury, the building owner or maintenance personnel should remove the grab bar from service if the grab bar is not adequately secured to wall or if there is any observed damage to the welds.

INSTALLATION:

Provide concealed anchor device or backing as specified or required in accordance with local building codes before wall is finished. Fasten concealed mounting flanges to anchor device or backing with at least two screws opposing each other in each flange. Snap flange covers over each mounting flange to conceal mount-ing screws. Concealed anchor devices and mounting screws are not included with Bobrick grab bars and must be specified as an accessory.

For Grab Bars with an Intermediate Flange(s), Pull Snap-Flange Covers away from mounting flanges. Place grab bar in desired mounting location. Use intermediate flange as a template to mark location of mounting screws at intermediate flange only. Mark screw locations at the center of the slot in the middle of the double-keyhole shaped mounting holes (2) in the intermediate flange. Remove grab bar from wall. Drive the intermediate flange mounting screws into wall at marked locations. Note: Make sure to leave a space of just over 1/8'' (3.17mm) between the underside of the screw head and the wall. Install grab bar on the wall by placing the round ends of the intermediate flange double-keyhole shaped mounting holes over the mounting screws (2) are located in the middle of the flange slots. Install the mounting screws into the wall at the end flanges and secure tightly. Tighten the mounting screws at the intermediate flange. Press all snap-flange covers into place to conceal mounting flanges.

Note: Recommend use of 1/4'' or #14 sheet metal or wood screws to install Intermediate Flange. #12 screws may also be used.

Important Notes:

1. Mounting Kits — Bobrick offers a mounting kit for installing grab bars; one Bobrick mounting kit is required for each flange.

2. Grab Bar Fastener — Bobrick offers a grab bar fastening system that secures all Bobrick grab bar series; one Bobrick fastener is required for each flange. Install grab bar without backing in wall requires minimum 5/8" (16mm) thick painted or tiled drywall.

3. Optional Anchor Device — Bobrick grab bar anchor device includes stainless steel machine screws to be used for attaching grab bars to anchors.

one Bobrick concealed anchor device is required for each flange.

SPECIFICATION:

Grab bar shall be type-304 stainless steel with satin-finish. Grab bar shall have 18-gauge (1.2mm) wall thickness and 1-1/4" (32mm) outside diameter. Clearance between the grab bar and wall shall be 1-1/2" (38mm). Concealed mounting flanges shall be 11-gauge (3.2 mm) thick stainless steel plate, 2" x 3-1/8" (50 x 80mm), and equipped with at least two screw holes for attachment to wall. Flange covers shall be 22-gauge (0.8mm) stainless steel, 3-1/4" (85mm) diameter, and shall snap over mounting flanges to conceal mounting screws and/or WingIt fasteners. Ends of grab bar shall pass through concealed mounting flanges and be heliarc welded to form one structural unit. Grab bar shall comply with accessible design (including ADAAG in the U.S.A.) for structural strength.

Grab Bar shall be Model __________ (insert model number) of Bobrick Washroom Equipment, Inc., Clifton Park, New York; Jackson, Tennessee; and Los Angeles, California; Bobrick Washroom Equipment Company, Scarborough, Ontario; Bobrick Washroom Equipment Pty.

Ltd., Australia; and Bobrick Washroom Equipment Limited, United Kingdom.

Description

Consists of 10–32 x 5/16'' round-head, Phillips 18/8 stainless steel screws.

(1) WingIt grab bar fastener.

WingIt™ Fastener No.

251-4

Mounting Kit No.

252-30

Description

Consists of (3) #14 x 2½'' type-304 stainless steel, Phillips round-head, sheet-metal screws.

Description

Anchor for 3/4" to 1" (19-25mm) panel 1 anchor required for…