8-Asbestos Survey Report - Tract 23.pdf

Facilities | Environmental | Geotechnical | Materials I

City of Olathe Public Improvements

Asbestos Survey

2004 East Santa Fe Street

Olathe, Kansas 66062

October 22, 2025 | Terracon Project Number: 02237230

Prepared for:

City of Olathe Kansas

100 East Santa Fe Street

Olathe, KS 66061

15620 W 113th Street

Lenexa, KS 66219

P (913) 492-7777

F (913) 492-7443

Terracon.com

Facilities | Environmental | Geotechnical | Materials i

October 22, 2025

City of Olathe, Kansas

100 East Santa Fe Street

Olathe, KS 66061

Attn: Ms. Therese Vink

P: (913) 971-9032

E: tmersmann@olatheks.org

Re: City of Olathe Public Improvements Asbestos Survey

2004 East Santa Fe Street

Olathe, Kansas 66062

Terracon Project No: 02237230

Dear Ms. Vink:

Terracon Consultants, Inc. (Terracon) is pleased to provide the City of Olathe, Kansas, with this report regarding an asbestos survey conducted at the above-referenced location in Olathe, Kansas.

Asbestos

Asbestos was identified at a concentration greater than 1% in samples collected from the following materials:

Material Description Material Location

NESHAP

Category Estimated Quantity

Transite Soffit Lobby - South Soffit Category II

Nonfriable 200 Square Feet

Roofing Tar Central Roof - NE Vent, South and West Perimeters Category I Nonfriable

18 Square Feet

Notes: NESHAP – National Emission Standards for Hazardous Air Pollutants

Please refer to Section 3.0 of the attached report for a detailed description of the asbestos survey, sampling activities, and findings.

City of Olathe Public Improvements Asbestos Survey

2004 East Santa Fe Street | Olathe, Kansas

October 22, 2025 | Terracon Project No. 02237230

Facilities | Environmental | Geotechnical | Materials ii

Terracon appreciates the opportunity to provide this service to the City of Olathe, Kansas. If you have any questions regarding this report, please contact our office at

913-492-7777.

Sincerely, Terracon

Ryan Slanczka Clark Grisell

Senior Staff Scientist Environmental Group Manager

Building Environmental Sciences

Ryan Slanczka Clark Grisell

Facilities | Environmental | Geotechnical | Materials iii

Table Of Contents

1.0 Introduction 1

1.1 Reliance 1

2.0 Building Description 1

3.0 Asbestos-Containing Materials Survey 1

3.1 Visual Assessment 1

3.2 Physical Assessment 2

3.3 Sample Collection 2

3.4 Sample Analysis 2

3.5 Regulatory Overview 2

3.6 Findings 3

4.0 General Comments 4

Appendices

Appendix A Asbestos-Containing Materials By Homogeneous Area

Appendix B Asbestos Survey Sample Location Summary

Appendix C Asbestos Laboratory Analytical Results

Appendix D Certifications

Facilities | Environmental | Geotechnical | Materials 1

1.0 Introduction

Terracon Consultants, Inc. (Terracon) conducted an asbestos-containing material survey of the building located at 2004 East Santa Fe Street in Olathe, Kansas, on April 16, 2025. Building areas were visually assessed for suspect asbestos-containing materials

(ACM). A reasonable effort was made to inspect accessible areas. Additional suspect materials could be present in walls, voids, or other concealed areas.

1.1 Reliance

This report is for the exclusive use of the City of Olathe, Kansas, for the project being discussed. Reliance by any other party on this report is prohibited without the written authorization of Terracon and the City of Olathe, Kansas.

2.0 Building Description

The subject building is a vacant, approximately 4,793-square-foot, single-story former fast food restaurant with a drive-through, reportedly constructed in 1976 with an addition constructed in 1998. Interior flooring finishes include ceramic tiles over concrete. Interior walls are ceramic tile and drywall wallboard. The ceiling system is a drop, grid ceiling with lay-in acoustic tiles. The building’s exterior has stucco and cement siding. The roof consists of a single-ply synthetic rubber membrane system, with a composite shingle canopy.

3.0 Asbestos-Containing Materials Survey

The survey was conducted by Mr. Ryan Slanczka and Mr. Blake Harris, State of Kansas-accredited asbestos inspectors. Copies of the asbestos inspectors’ accreditations are attached as Appendix D. The survey was conducted in general accordance with the sample collection protocols established in the United States Environmental Protection

Agency (USEPA) 40 Code of Federal Regulations (CFR) Part 763 Subpart E 763.86, the

Asbestos Hazard Emergency Response Act (AHERA). A summary of survey activities is provided below.

3.1 Visual Assessment

Survey activities were initiated with visual observation of the interior and exterior of the building to identify homogeneous areas of suspect ACM. A homogeneous area (HA)

Facilities | Environmental | Geotechnical | Materials 2 consists of a building material that appears similar throughout in terms of color and texture, with consideration given to the date of application. The assessment was conducted in visually accessible areas of the building scheduled for renovation.

3.2 Physical Assessment

A physical assessment of each HA of suspect ACM was conducted to assess the friability and condition of the materials. A friable material is defined by the USEPA as a material that can be crumbled, pulverized, or reduced to powder by hand pressure when dry.

Friability was assessed by physically touching suspect materials.

3.3 Sample Collection

Based on the results of the visual observation, bulk samples of suspect ACM samples were collected in general accordance with USEPA AHERA sampling protocols. Samples of suspect materials were collected from randomly selected locations in each homogeneous area. Bulk samples were collected using wet methods, as applicable, to reduce the potential for fiber release. Samples were placed in sealable containers and labeled with unique sample numbers using an indelible marker.

Rubber, wood products, plastic products, glass, and steel are not considered suspect

ACM and were, therefore, not sampled. The selection of sample locations and frequency of sampling were based on Terracon’s observations and the assumption that like materials in the same area are homogeneous in content. Terracon collected 107 bulk samples from 33 homogeneous areas of suspect ACM.

3.4 Sample Analysis

Bulk samples were submitted under chain of custody to Eurofins International Asbestos

Testing Laboratories (Eurofins) of Mount Laurel, New Jersey, for analysis by PLM with dispersion staining techniques per USEPA Method 600/R-93/116. The percentage of asbestos, where applicable, was determined by microscopic visual estimation. Eurofins is accredited under the National Voluntary Laboratory Accreditation Program (NVLAP), Accreditation No. 101165.

3.5 Regulatory Overview

The asbestos National Emission Standards for Hazardous Air Pollutants (NESHAP) regulation (40 CFR Part 61, Subpart M) regulates asbestos fiber emissions and asbestos waste disposal practices. The asbestos NESHAP regulation also requires the identification and classification of existing ACM according to friability prior to demolition or renovation

Facilities | Environmental | Geotechnical | Materials 3 activity. Friable ACM is a material containing more than 1% asbestos that, when dry, can be crumbled, pulverized, or reduced to powder by hand pressure.

The asbestos NESHAP regulation classifies ACM as regulated asbestos-containing materials (RACM), Category I non-friable ACM, or Category II non-friable ACM. RACM includes all friable ACM; Category I non-friable ACM that has become friable or will be or has been subjected to sanding, grinding, cutting, or abrading; and Category II non-friable ACM that has a high probability of becoming or has become crumbled, pulverized, or reduced to powder in the course of renovation or demolition activity. Category I non-friable ACM are exclusively asbestos-containing packings, gaskets, resilient floor coverings, resilient floor covering mastics, and asphalt roofing products that contain more than 1% asbestos. Category II non-friable ACM are all other non-friable materials other than Category I non-friable ACM that contain more than 1% asbestos. Category II non-friable ACM generally includes but is not limited to cementitious material such as cement pipes, cement siding, cement panels, glazing, mortar, and grouts.

The Kansas Department of Health and Environment’s (KDHE) Asbestos Control Section within the Bureau of Air enforces the Asbestos NESHAP as adopted by reference at

Kansas Administrative Regulations (K.A.R.) 28-19-735. The owner or operator must provide KDHE with written notification at least 10 working days prior to the commencement of asbestos abatement activities that will disturb RACM in amounts greater than or equal to 10 square feet or 25 linear feet.

The United States Occupational Safety and Health Administration (USOSHA) asbestos standard for construction (29 CFR 1926.1101) regulates workplace exposure to asbestos. The OSHA standard classifies construction and maintenance activities that could disturb ACM and specifies work practices and precautions that employers must follow when engaging in each class of regulated work. The standard also specifies requirements for handling materials containing asbestos in concentrations less than or equal to one percent.

3.6 Findings

Asbestos was identified at a concentration greater than 1% in samples collected from the following materials:

Material Description Material Location

NESHAP

Category Estimated Quantity

Transite Soffit Lobby - South Soffit Category II

Nonfriable 200 Square Feet

Roofing Tar Central Roof - NE Vent, South and West Perimeters Category I

Nonfriable 18 Square Feet

Notes: NESHAP – National Emission Standards for Hazardous Air Pollutants

Facilities | Environmental | Geotechnical | Materials 4

The above-listed Category I non-friable ACM that is damaged or could be damaged to the extent that it could be crumbled, pulverized, or reduced to powder when dry, making it friable, must be removed prior to any activities (renovation and/or demolition) that may disturb this material in accordance with applicable federal, state, and local regulations. Terracon recommends that all ACM be removed by an abatement contractor prior to any demolition or renovation work that may disturb it.

The above-listed Category II non-friable ACM that has a high probability of becoming crumbled, pulverized, or reduced to powder when dry, making it friable, must be properly removed prior to any activities (renovation and/or demolition) that may disturb this material in accordance with applicable federal, state, and local regulations. USEPA believes that most demolition activities will subject Category II non-friable ACM to the asbestos NESHAP regulation.

A summary of identified asbestos-containing materials by homogeneous area is included in Appendix A. A summary of sample locations is included in Appendix B. Laboratory analytical reports are included in Appendix C.

4.0 General Comments

Terracon did not perform sampling that required demolition or destructive activities, such as dismantling of equipment or removal of protective coverings. Reasonable efforts to access suspect materials within known areas of restricted access (e.g., crawl spaces) were made; however, confined spaces or areas that may pose a health or safety risk to

Terracon personnel were not sampled. Sampling did not include suspect materials that could not be safely reached with available ladders or manlifts. Terracon did not sample suspect materials that may be present in movable equipment such as freezers, kitchen equipment, and hoods. Terracon typically investigates for flooring beneath carpeting by lifting small corner sections of carpet. If tiles or sheet vinyl were seen, they have been identified in the report. If tiles or sheet vinyl were not seen at corners under the carpet, it does not imply that there is none beneath the carpeted floor. Terracon did not conduct a destructive investigation of the doors in the building to determine if the doors were insulated for fire-rating purposes.

This survey was conducted in a manner consistent with the level of care and skill ordinarily exercised by members of the profession currently practicing under similar conditions in the same locale. The results, findings, conclusions, and recommendations expressed in this report are based on conditions observed during Terracon’s survey of the building. The information contained in this report is relevant to the date on which this survey was performed, and should not be relied upon to represent conditions at a later date. This report has been prepared on behalf of and exclusively for use by the City of Olathe, Kansas, and is not a bidding document. Contractors or consultants reviewing this report must draw their own conclusions regarding further investigation or

Facilities | Environmental | Geotechnical | Materials 5 remediation deemed necessary. Terracon does not warrant the work of regulatory agencies, laboratories, or other third parties supplying information that may have been used in the preparation of this report. No warranty, express or implied, is made.

Appendix A

Asbestos-Containing Materials By Homogeneous Area

Appendix A

Identified Asbestos-Containing Materials By Homogeneous Area (HA)

2004 East Santa Fe Street, Olathe, Kansas

Terracon Project No. 02237230

HA Material Description Material Location % and Type

Asbestos*

NESHAP

Classification Condition

Estimated

Quantity**

7 Transite Soffit Lobby - South Soffit

Grey Transite Soffit - 15%

Chrysotile

Tan Texture - None Detected

Category II

Nonfriable Good

200 Square

Feet

29 Roofing Tar

Central Roof - NE

Vent, South and West

Perimeters

Black/Grey Roofing Tar - 5%

Chrysotile

Category I

Nonfriable Good

18 Square

Feet

*% & Type Asbestos – this column contains both the analytical result of the sample with the highest concentration of asbestos detected in the samples that make up the HA, and the types of asbestos identified.

**Estimated quantities – quantities based on a cursory field evaluation, and actual quantities may vary significantly, especially if asbestos-containing materials are present in hidden and/or inaccessible areas not evaluated as part of this survey. This is not a bidding document; contractors are responsible for determining their own opinion of quantities.

Appendix B

Asbestos Survey Sample Location Summary

Appendix B

Asbestos Survey Sample Location Summary

2004 East Santa Fe Street, Olathe, Kansas

Terracon Project No. 02237230

HA

No.

Material Description

Sample

Number Sample Location Sample Layer Description Lab Results

Drywall with Joint

Compound

01-WB5-01

Playroom - North Wall, Central

Area

Brown/White Drywall

None Detected

White Joint Compound

Yellow/Beige Tape

01-WB5-02

NE Storage Room - South Wall, West Area Brown/White Drywall

01-WB5-03 Lobby - Ceiling, North of Vestibule

Brown/White Drywall

White Joint Compound

Yellow/Beige Tape

6" x 6" White/Red/Yellow

Ceramic Wall Tile with

Grout and Mortar

02-MA5-04

Lobby - Front Counter Wall, West

Area

White Ceramic Tile

None Detected

White Grout

White Mastic

02-MA5-05

Kitchen - Dividing Wall, Central

Area

White Ceramic Tile

White Grout

White Mastic

Material Description

Sample

Number Sample Location Sample Layer Description Lab Results

6" x 6" White/Red/Yellow

Ceramic Wall Tile with

Grout and Mortar

02-MA5-06 North Restroom - East Wall

White Ceramic Tile

None Detected White Grout

White Mastic

4" x 4" White Ceramic Wall

Tile with Grout and Mortar

03-MA5-07 Kitchen - East Wall

White Ceramic Tile

None Detected

White Grout

White Mastic

03-MA5-08 Kitchen - North Wall

White Ceramic Tile

White Grout

Yellow Mastic

Tan Mastic (Top of tile)

03-MA5-09 Kitchen - SW Area, South Wall

White Ceramic Tile

White Grout

Yellow Mastic

2" x 4" Red Ceramic Wall

Tile with Grout and Mortar 04-MA5-10 Lobby - SE Wall

Red Ceramic Tile

None Detected

Brown/Red Grout

Yellow Mastic

White Leveling Compound

Brown Paper

Material Description

Sample

Number Sample Location Sample Layer Description Lab Results

2" x 4" Red Ceramic Wall

Tile with Grout and Mortar

04-MA5-11 Lobby - SE Wall

Red Ceramic Tile

None Detected

Brown/Red Grout

Yellow Mastic

White Leveling Compound

Brown Paper

04-MA5-12 Lobby - SE Wall

Red Ceramic Tile

Brown/Red Grout

Yellow Mastic

White Leveling Compound

Brown Paper

5 Plaster Skim Coat

05-PL3-13 Lobby - SE Wall White Skim Coat

None Detected

05-PL3-14

Playroom - North Wall, Central

Area White Skim Coat

05-PL3-15

Dining Room - West Wall, North

Area White Skim Coat

05-PL3-16 Lobby - West Wall White Skim Coat

05-PL3-17 Lobby - Ceiling, North of Vestibule White Skim Coat

05-PL3-18

Dining Room - North Wall, Central

Area White Skim Coat

05-PL3-19 Playroom - East Wall, Central Area White Skim Coat

Material Description

Sample

Number Sample Location Sample Layer Description Lab Results

6 Wallpaper

06-PM5-20

Dining Room - West Wall, Central

Area Multi-colored Wallpaper

None Detected 06-PM5-21 Dining Room - West Wall, South

Area Multi-colored Wallpaper

06-PM5-22

Dining Room - North Wall, Central

Area Multi-colored Wallpaper

7 Transite Soffit

07-CP1-23 Lobby - South Soffit, West Area

Grey Transite (Soffit) 15% Chrysotile

Tan Texture None Detected

07-CP1-24 Lobby - South Soffit, West Area

Grey Transite (Soffit) 15% Chrysotile

Tan Texture None Detected

07-CP1-25 Lobby - South Soffit, East Area

Grey Transite (Soffit) 15% Chrysotile

Tan Texture None Detected

2'x4' White Ceiling Tile with

Pinholes and Divots

08-CT4-26 Lobby - NW Area White Ceiling Tile

None Detected 08-CT4-27 Lobby - SE Area White Ceiling Tile

08-CT4-28 Dining Room - Central Area White Ceiling Tile

2'x4' White Ceiling Tile with

Pinholes and Scratches

09-CT4-29 Dining Room - South-Central Area White Ceiling Tile

None Detected 09-CT4-30 Lobby - NW Area White Ceiling Tile

09-CT4-31 Lobby - SE Area White Ceiling Tile

2'x4' White Ceiling Tile with

Pinholes and Fissures

10-CT4-32 Dining Room - South-Central Area White Ceiling Tile

None Detected 10-CT4-33 Dining Room - North-Central Area White Ceiling Tile

10-CT4-34 Dining Room - SE Area White Ceiling Tile

Material Description

Sample

Number Sample Location Sample Layer Description Lab Results

2'x4' White Gypsum Ceiling

Tile

11-CT4-35 Kitchen - SE Area Brown Ceiling Tile with White

Surface

None Detected 11-CT4-36 Kitchen - NW Area Brown Ceiling Tile with White

Surface

11-CT4-37 NE Storage Room - SW Area Brown Ceiling Tile with White

Surface

12 Concrete Block Mortar

12-MA2-38 Kitchen - NE Area, West Wall Grey Mortar

None Detected 12-MA2-39 Kitchen - NE Area, East Wall Grey Mortar

12-MA2-40 North Exterior - East Outer Wall Grey Mortar

4" x 8" Faux-Wood Ceramic

Floor Tile with Grout and

Mortar

13-MA5-41 Dining Room - SE Area

Brown Ceramic Tile

None Detected

Black Grout

Light Grey Mortar

13-MA5-42 Playroom - North-Central Area

Brown Ceramic Tile

Black Grout

Light Grey Mortar

13-MA5-43 Lobby - NW Area

Brown Ceramic Tile

Black Grout

Light Grey Mortar

6" x 6" Red/Dark Brown

Ceramic Floor/Cove Base

Tile with Grout and Mortar

14-MA5-44 Kitchen - West-Central Area, Floor

Brown/Red Ceramic Tile

None Detected Black Grout

Light Grey Mortar

Material Description

Sample

Number Sample Location Sample Layer Description Lab Results

6" x 6" Red/Dark Brown

Ceramic Floor/Cove Base

Tile with Grout and Mortar

14-MA5-45 Kitchen - East-Central Area, Floor

Brown/Red Ceramic Tile

None Detected

Black Grout

Light Grey Mortar

14-MA5-46

Kitchen - NW Room, West Wall, Cove Base

Brown/Red Ceramic Tile

Black Grout

Light Grey Mortar

4" Cove Base with Tan

Mastic

15-FC3-47

NE Storage Room - West Wall, South Area

Grey Cove Base

None Detected

Tan Cove Base Mastic

15-FC3-48

NE Storage Room - West Wall, Central Area

Grey Cove Base

Tan Cove Base Mastic

15-FC3-49

NE Storage Room - North Wall, East Area

Grey Cove Base

Tan Cove Base Mastic

4" x 6" Faux-Wood Ceramic

Cove Base Tile with Grout and Mortar

16-MA5-50

Playroom - North Wall, Central

Area

Grey/Brown Ceramic Tile

None Detected

Black Grout

White Compound

White Fibrous Material (Mesh

Tape)

Grey CMU

Tan Mastic

Material Description

Sample

Number Sample Location Sample Layer Description Lab Results

4" x 6" Faux-Wood Ceramic

Cove Base Tile with Grout and Mortar

16-MA5-51 Lobby - South Wall, West Area

Grey/Brown Ceramic Tile

None Detected

Black Grout

White Cementitious Material

Grey Mortar

16-MA5-52

Dining Room - West Wall, Central

Area

Grey/Brown Ceramic Tile

Black Grout

White Fibrous Material (Mesh

Tape)

Grey CMU

17 Black Wall Mastic

17-MG5-53 Lobby - SE Wall

Black Mastic

None Detected

White Joint Compound

17-MG5-54 Lobby - SE Wall

Black Mastic

White Joint Compound

17-MG5-55 Lobby - SE Wall

Black Mastic

White Joint Compound

18 Ceramic Cove Base Caulk

18-CA5-56

Playroom - North Wall, Central

Area Cream Caulk

None Detected 18-CA5-57 Playroom - North Wall, Central

Area Cream Caulk

18-CA5-58 Playroom - South Wall, West Area Cream Caulk

Material Description

Sample

Number Sample Location Sample Layer Description Lab Results

Tan Fiber Reinforced Panel

Mastic

19-MG8-59 Kitchen - East Wall Tan FRP Mastic

None Detected 19-MG8-60 Kitchen - North Wall Tan FRP Mastic

19-MG8-61 Kitchen - NE Area, South Wall Tan FRP Mastic

Dark Brown Fiber

Reinforced Panel Mastic

20-MG8-62 Kitchen - NW Room, South Wall

Brown FRP Mastic

None Detected

White Joint Compound

20-MG8-63 Kitchen - NW Room, South Wall

Brown FRP Mastic

White Joint Compound

20-MG8-64 Kitchen - NW Room, South Wall

Brown FRP Mastic

White Joint Compound

21 Fiberglass Pipe Insulation

21-PI4-65 Kitchen - NW Area

Yellow Insulation

None Detected

Silver Foil/Brown Paper/Tan

Adhesive

21-PI4-66 NE Storage Room - SW Area

Yellow Insulation

Silver Foil/Brown Paper/Tan

Adhesive

21-PI4-67 Kitchen - NE Area

Yellow Insulation

Silver Foil/Brown Paper/Tan

Adhesive

22 Expansion Joint

22-MS5-68

West Exterior - Drive-Thru Lane, North Area Black Expansion Joint

None Detected 22-MS5-69 West Exterior - Drive-Thru Lane, Central Area Black Expansion Joint

22-MS5-70

West Exterior - Drive-Thru Lane, Central Area Black Expansion Joint

Material Description

Sample

Number Sample Location Sample Layer Description Lab Results

23 Stucco

23-MA6-71 East Exterior - North Area

White Stucco with Paint

None Detected

Grey Stucco

23-MA6-72 South Exterior - SE Corner

White Stucco with Paint

Grey Stucco

23-MA6-73

North Exterior - East Area, near

Playroom Window

White Stucco with Paint

Grey Stucco

24 Concrete Wall Texture

24-SC5-74 Lobby - South Soffit, East Area White Texture with Paint

None Detected

24-SC5-75 South Exterior - near East Door White Texture with Paint

24-SC5-76

West Exterior - South of NW

Window White Texture with Paint

24-SC5-77 South Exterior - SE Corner White Texture with Paint

24-SC5-78

North Exterior - West Area, near

NW Window White/Grey Texture with Paint

24-SC5-79 South Exterior - SW Corner White Texture with Paint

24-SC5-80 East Exterior - NE Corner White Texture with Paint

25 Cement Siding

25-CP4-81 West Exterior - SW Column Grey Transite

None Detected 25-CP4-82 West Exterior - NW Column Grey Transite

25-CP4-83 South Exterior - near Vestibule Grey Transite

Material Description

Sample

Number Sample Location Sample Layer Description Lab Results

26 Cement Chair Rail

26-CP1-84 West Exterior - near NW Window Off-White Non-Fibrous

Material

None Detected 26-CP1-85 North Exterior - near Door Off-White Non-Fibrous

Material

26-CP1-86 South Exterior - near Vestibule Off-White Non-Fibrous

Material

27 Penetration Sealant

27-SC5-87

Central Roof - West Perimeter, Central Area White Sealant

None Detected 27-SC5-88 Central Roof - East Perimeter, Central Area White Sealant

27-SC5-89 Central Roof - NE Area, on Vent White Sealant

28 Black Roofing Tar

28-RF1-90

Central Roof - Central Area, on

Pipe Black Roofing Tar

None Detected 28-RF1-91 Central Roof - SE Area, on AHU Black Roofing Tar

28-RF1-92 Central Roof - NE Area, on Pipe Black Roofing Tar

29 Roofing Tar

29-RF1-93 Central Roof - NE Area, on Vent Black/Grey Roofing Tar 5% Chrysotile

29-RF1-94

Central Roof - West Perimeter, South Area Black/Grey Roofing Tar 5% Chrysotile

29-RF1-95

Central Roof - South Perimeter, West-Central Area Black/Grey Roofing Tar 5% Chrysotile

30 Asphalt Shingles

30-RF3-96 East-Central Roof - NW Perimeter

Black Roofing Shingle

None Detected

Black Tar Paper

30-RF3-97 West-Central Roof - NE Perimeter

Black Roofing Shingle

Black Tar Paper

30-RF3-98 NE Lower Roof - North Perimeter

Black Roofing Shingle

Black Tar Paper

Material Description

Sample

Number Sample Location Sample Layer Description Lab Results

Rolled Asphalt Roofing with

Tar

31-RF3-99

Central Roof - East Perimeter, Central Area

Black Roofing Shingle

None Detected

Black Tar

31-RF3-100

Central Roof - South Perimeter, Central Area

Black Roofing Shingle

Black Tar

31-RF3-101

Central Roof - North Perimeter, West Area

Black Roofing Shingle

Black Tar

32 Roofing Membrane

32-RF6-102 Central Roof - NE Area

Green Ceiling Tile (Foam)

None Detected

Yellow Foam

Black Paper

White Roofing Membrane

32-RF6-103 Central Roof - NW Area

Green Ceiling Tile (Foam)

Yellow Foam

Black Paper

White Roofing Membrane

32-RF6-104 Central Roof - South-Central Area

Green Ceiling Tile (Foam)

Yellow Foam

Black Paper

White Roofing Membrane

Material Description

Sample

Number Sample Location Sample Layer Description Lab Results

33 Patch Insulation

33-RF9-105 Central Roof - Hatch Perimeter

Black Tar

None Detected

Brown Insulation

33-RF9-106 Central Roof - Hatch Perimeter

Black Tar

Brown Insulation

33-RF9-107 Central Roof - Hatch Perimeter

Black Tar

Brown Insulation

Asbestos-containing materials in BOLD.

Appendix C

Asbestos Laboratory Analytical Results

Approved by:

Approved Signatory Frank Ehrenfeld

Report for:

Ryan Slanczka Terracon Consultants- Lenexa 15620 W. 113th St Lenexa, KS 66219

Regarding:

Eurofins Built Environment Testing East, LLC Project: 02237230 - 2004 E. Santa Fe St

EML ID: 4036622

All samples were received in acceptable condition unless noted in the Report Comments portion in the body of the report. The results relate only to the samples as received and tested. The results include an inherent uncertainty of measurement associated with estimating percentages by polarized light microscopy. Measurement uncertainty data for sample results with >1% asbestos concentration can be provided when requested.

Eurofins Built Environment Testing East, LLC ("the Company"), a member of the Eurofins Built Environment Testing group of companies, shall have no liability to the client or the client's customer with respect to decisions or recommendations made, actions taken or courses of conduct implemented by either the client or the client's customer as a result of or based upon the Test Results. In no event shall the Company be liable to the client with respect to the Test Results except for the Company's own willful misconduct or gross negligence nor shall the Company be liable for incidental or consequential damages or lost profits or revenues to the fullest extent such liability may be disclaimed by law, even if the Company has been advised of the possibility of such damages, lost profits or lost revenues. In no event shall the Company's liability with respect to the Test Results exceed the amount paid to the Company by the client therefor.

Dates of Analysis:

Asbestos PLM (Layer %): 10-15-2025

Service SOPs: Asbestos PLM (Layer %) (EPA 40CFR App E to Sub E of Part 763 & EPA METHOD 600/R-93-116, SOP EB-AS-S- 1267) NVLAP Lab Code 101165-0

EMLab ID: 4036622, Page 1 of 21Eurofins Built Environment Testing East, LLC

Eurofins Built Environment Testing East, LLC 9000 Commerce Parkway, Suite B, Mount Laurel, NJ 08054

(856) 231-9449 www.eurofinsus.com/Built Client: Terracon Consultants- Lenexa C/O: Ryan Slanczka Re: 02237230 - 2004 E. Santa Fe St

Date of Receipt: 04-18-2025 Date of Report: 10-15-2025

Bulk Asbestos Fiber Analysis by Polarized Light Microscopy (PLM) Appx E Sub E 40 CFR 763 / EPA 600/R-93/116

Sample ID # Lab-ID version Sample Description Asbestos

Constituents Non-Asbestos Constituents Comment

01-WB5-01. Drywall with Joint Compound; Playroom-North Wall, Central Area 20104178-1

Layer 1 Brown/White Drywall Homogeneity:Good

Not Detected 85% Non-Fibrous Material 15% Cellulose

Layer 2 White Joint Compound Homogeneity:Good

Not Detected 100% Non-Fibrous Material

Layer 3 Yellow/ Beige Tape Homogeneity:Good

Not Detected 90% Cellulose 10% Non-Fibrous Material

Composite Asbestos ND

01-WB5-02. Drywall with Joint Compound; NE Storage Room-South Wall, West Area 20104179-1

Layer 1 Brown/White Drywall Homogeneity:Good

Not Detected 85% Non-Fibrous Material 15% Cellulose

A

01-WB5-03. Drywall with Joint Compound; Lobby-Ceiling, North of Vestibule 20104180-1

Layer 1 Brown/White Drywall Homogeneity:Good

Yellow/ Beige Tape Homogeneity:Good

Composite Asbestos ND

02-MA5-04. 6"x6" White/Red/Yellow Ceramic Wall Tile w/ Grout & Mortar;

Lobby-Front Counter Wall, West Area 20104181-1

Layer 1 White Ceramic Tile

Not Detected 100% Non-Fibrous Material B

Comments: A)No joint compound present, composite not possible. B)Sample does not match sample description provided by client.

EMLab ID: 4036622, Page 2 of 21Eurofins Built Environment Testing East, LLC

The total percentage of sample components shown may be greater than 100% when some components are detected at <1%.

The test report shall not be reproduced except in full, without written approval of the laboratory. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. The Company reserves the right to dispose of all samples after a period of thirty (30) days, according to all state and federal guidelines, unless otherwise specified.

Inhomogeneous samples are separated into homogeneous subsamples and analyzed individually. ND means no fibers of that type were detected.

When detected, the minimum detection and reporting limit is less than 1% unless point counting is performed. Floor tile samples may contain large amounts of interference material and it is recommended that the sample be analyzed by gravimetric point count analysis to lower the detection limit and to aid in asbestos identification.

‡ A "Version" indicated by -"x" after the Lab ID# with a value greater than 1 indicates a sample with amended data. The revision number is reflected by the value of "x".

(856) 231-9449 www.eurofinsus.com/Built Client: Terracon Consultants- Lenexa C/O: Ryan Slanczka Re: 02237230 - 2004 E. Santa Fe St

Date of Receipt: 04-18-2025 Date of Report: 10-15-2025

Bulk Asbestos Fiber Analysis by Polarized Light Microscopy (PLM) Appx E Sub E 40 CFR 763 / EPA 600/R-93/116

Sample ID # Lab-ID version Sample Description Asbestos

Constituents Non-Asbestos Constituents Comment

02-MA5-04. 6"x6" White/Red/Yellow Ceramic Wall Tile w/ Grout & Mortar;

Lobby-Front Counter Wall, West Area 20104181-1(cont.)

Layer 2 White Grout

Not Detected 100% Non-Fibrous Material A

Homogeneity:Good

Not Detected 100% Non-Fibrous Material A

02-MA5-05. 6"x6" White/Red/Yellow Ceramic Wall Tile w/ Grout & Mortar;

Kitchen-Dividing Wall, Central Area 20104182-1

Layer 1 White Ceramic Tile

Homogeneity:Good

Not Detected 100% Non-Fibrous Material B

02-MA5-06. 6"x6" White/Red/Yellow Ceramic Wall Tile w/ Grout & Mortar;

North Restroom-East Wall 20104183-1

Layer 1 White Ceramic Tile

Homogeneity:Good

Not Detected 100% Non-Fibrous Material A

03-MA5-07. 4x4" White Ceramic Wall Tile with Grout & Mastic; Kitchen- East Wall 20104184-1

Layer 1 White Ceramic Tile

Comments: A)Sample does not match sample description provided by client. B)Sample does not match sample description provided by client.

EMLab ID: 4036622, Page 3 of 21Eurofins Built Environment Testing East, LLC

The total percentage of sample components shown may be greater than 100% when some components are detected at <1%.

The test report shall not be reproduced except in full, without written approval of the laboratory. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. The Company reserves the right to dispose of all samples after a period of thirty (30) days, according to all state and federal guidelines, unless otherwise specified.

Inhomogeneous samples are separated into homogeneous subsamples and analyzed individually. ND means no fibers of that type were detected.

When detected, the minimum detection and reporting limit is less than 1% unless point counting is performed. Floor tile samples may contain large amounts of interference material and it is recommended that the sample be analyzed by gravimetric point count analysis to lower the detection limit and to aid in asbestos identification.

‡ A "Version" indicated by -"x" after the Lab ID# with a value greater than 1 indicates a sample with amended data. The revision number is

(856) 231-9449 www.eurofinsus.com/Built Client: Terracon Consultants- Lenexa C/O: Ryan Slanczka Re: 02237230 - 2004 E. Santa Fe St

Date of Receipt: 04-18-2025 Date of Report: 10-15-2025

Bulk Asbestos Fiber Analysis by Polarized Light Microscopy (PLM) Appx E Sub E 40 CFR 763 / EPA 600/R-93/116

Sample ID # Lab-ID version Sample Description Asbestos

Constituents Non-Asbestos Constituents Comment

03-MA5-07. 4x4" White Ceramic Wall Tile with Grout & Mastic; Kitchen- East Wall 20104184-1(cont.)

Layer 2 White Grout

Homogeneity:Good

Not Detected 100% Non-Fibrous Material

03-MA5-08. 4x4" White Ceramic Wall Tile with Grout & Mastic; Kitchen- North Wall 20104185-1

Layer 1 White Ceramic Tile

Yellow Mastic

Layer 4 Tan Mastic (Top of tile) Homogeneity:Good

Not Detected 100% Non-Fibrous Material

03-MA5-09. 4x4" White Ceramic Wall Tile with Grout & Mastic; Kitchen-SW Area, South Wall 20104186-1

Layer 1 White Ceramic Tile

Homogeneity:Good

Not Detected 100% Non-Fibrous Material

Comments:

EMLab ID: 4036622, Page 4 of 21Eurofins Built Environment Testing East, LLC

The total percentage of sample components shown may be greater than 100% when some components are detected at <1%.

The test report shall not be reproduced except in full, without written approval of the laboratory. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. The Company reserves the right to dispose of all samples after a period of thirty (30) days, according to all state and federal guidelines, unless otherwise specified.

Inhomogeneous samples are separated into homogeneous subsamples and analyzed individually. ND means no fibers of that type were detected.

When detected, the minimum detection and reporting limit is less than 1% unless point counting is performed. Floor tile samples may contain large amounts of interference material and it is recommended that the sample be analyzed by gravimetric point count analysis to lower the detection limit and to aid in asbestos identification.

‡ A "Version" indicated by -"x" after the Lab ID# with a value greater than 1 indicates a sample with amended data. The revision number is

(856) 231-9449 www.eurofinsus.com/Built Client: Terracon Consultants- Lenexa C/O: Ryan Slanczka Re: 02237230 - 2004 E. Santa Fe St

Date of Receipt: 04-18-2025 Date of Report: 10-15-2025

Bulk Asbestos Fiber Analysis by Polarized Light Microscopy (PLM) Appx E Sub E 40 CFR 763 / EPA 600/R-93/116

Sample ID # Lab-ID version Sample Description Asbestos

Constituents Non-Asbestos Constituents Comment

04-MA5-10. 2x4" Red Ceramic Wall Tile with Grout & Mastic; Lobby-SE Wall 20104187-1(cont.)

Layer 1 Red Ceramic Tile

Brown/ Red Grout

Layer 5

Homogeneity:Good

04-MA5-11. 2x4" Red Ceramic Wall Tile with Grout & Mastic; Lobby-SE Wall 20104188-1

Layer 1 Red Ceramic Tile

Homogeneity:Good

Comments:

EMLab ID: 4036622, Page 5 of 21Eurofins Built Environment Testing East, LLC

The total percentage of sample components shown may be greater than 100% when some components are detected at <1%.

The test report shall not be reproduced except in full, without written approval of the laboratory. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. The Company reserves the right to dispose of all samples after a period of thirty (30) days, according to all state and federal guidelines, unless otherwise specified.

Inhomogeneous samples are separated into homogeneous subsamples and analyzed individually. ND means no fibers of that type were detected.

When detected, the minimum detection and reporting limit is less than 1% unless point counting is performed. Floor tile samples may contain large amounts of interference material and it is recommended that the sample be analyzed by gravimetric point count analysis to lower the detection limit and to aid in asbestos identification.

‡ A "Version" indicated by -"x" after the Lab ID# with a value greater than 1 indicates a sample with amended data. The revision number is

(856) 231-9449 www.eurofinsus.com/Built Client: Terracon Consultants- Lenexa C/O: Ryan Slanczka Re: 02237230 - 2004 E. Santa Fe St

Date of Receipt: 04-18-2025 Date of Report: 10-15-2025

Bulk Asbestos Fiber Analysis by Polarized Light Microscopy (PLM) Appx E Sub E 40 CFR 763 / EPA 600/R-93/116

Sample ID # Lab-ID version Sample Description Asbestos

Constituents Non-Asbestos Constituents Comment

04-MA5-12. 2x4" Red Ceramic Wall Tile with Grout & Mastic; Lobby-SE Wall 20104189-1

Layer 1 Red Ceramic Tile

Homogeneity:Good

05-PL3-13. Plaster Skim Coat; Lobby- SE Wall 20104190-1

Layer 1 White Skim Coat Homogeneity:Good

Not Detected 100% Non-Fibrous Material

05-PL3-14. Plaster Skim Coat;

Playroom-North Wall, Central Area 20104191-1

Layer 1 White Skim Coat Homogeneity:Good

Not Detected 100% Non-Fibrous Material

05-PL3-15. Plaster Skim Coat; Dining Room-West Wall, North Area 20104192-1

Layer 1 White Skim Coat Homogeneity:Good

Not Detected 100% Non-Fibrous Material

05-PL3-16. Plaster Skim Coat; Lobby- West Wall 20104193-1

Layer 1 White Skim Coat Homogeneity:Good

Not Detected 100% Non-Fibrous Material

05-PL3-17. Plaster Skim Coat; Lobby- Ceiling, North of Vestibule 20104194-1

Layer 1 White Skim Coat Homogeneity:Good

Not Detected 100% Non-Fibrous Material

05-PL3-18. Plaster Skim Coat; Dining Room-North Wall, Cental Area 20104195-1

Layer 1 White Skim Coat Homogeneity:Good

Not Detected 100% Non-Fibrous Material

05-PL3-19. Plaster Skim Coat;

Playroom-East Wall, Central Area 20104196-1

Layer 1 White Skim Coat Homogeneity:Good

Not Detected 100% Non-Fibrous Material

Comments:

EMLab ID: 4036622, Page 6 of 21Eurofins Built Environment Testing East, LLC

The total percentage of sample components shown may be greater than 100% when some components are detected at <1%.

The test report shall not be reproduced except in full, without written approval of the laboratory. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. The Company reserves the right to dispose of all samples after a period of thirty (30) days, according to all state and federal guidelines, unless otherwise specified.

Inhomogeneous samples are separated into homogeneous subsamples and analyzed individually. ND means no fibers of that type were detected.

When detected, the minimum detection and reporting limit is less than 1% unless point counting is performed. Floor tile samples may contain large amounts of interference material and it is recommended that the sample be analyzed by gravimetric point count analysis to lower the detection limit and to aid in asbestos identification.

‡ A "Version" indicated by -"x" after the Lab ID# with a value greater than 1 indicates a sample with amended data. The revision number is

(856) 231-9449 www.eurofinsus.com/Built Client: Terracon Consultants- Lenexa C/O: Ryan Slanczka Re: 02237230 - 2004 E. Santa Fe St

Date of Receipt: 04-18-2025 Date of Report: 10-15-2025

Bulk Asbestos Fiber Analysis by Polarized Light Microscopy (PLM) Appx E Sub E 40 CFR 763 / EPA 600/R-93/116

Sample ID # Lab-ID version Sample Description Asbestos

Constituents Non-Asbestos Constituents Comment

06-PM5-20. Wallpaper; Dining Room- West Wall, Central Area 20104197-1

Layer 1 Multi-colored Wallpaper Homogeneity:Good

06-PM5-21. Wallpaper; Dining Room- West Wall, South Area 20104198-1

Layer 1 Multi-colored Wallpaper Homogeneity:Good

06-PM5-22. Wallpaper; Dining Room- North Wall, Central Area 20104199-1

Layer 1 Multi-colored Wallpaper Homogeneity:Good

07-CP1-23. Transite Soffit; Lobby- South Soffit, West Area 20104200-1

Layer 1 Gray Transite (Soffit)

15% Chrysotile 85% Non-Fibrous Material

Tan Texture Homogeneity:Good

Not Detected 100% Non-Fibrous Material

07-CP1-24. Transite Soffit; Lobby- South Soffit, West Area 20104201-1

Layer 1 Gray Transite (Soffit)

Homogeneity:Good

Not Detected 100% Non-Fibrous Material

07-CP1-25. Transite Soffit; Lobby- South Soffit, East Area 20104202-1

Layer 1 Gray Transite (Soffit)

Homogeneity:Good

Not Detected 100% Non-Fibrous Material

08-CT4-26. 2'x4' White Ceiling Tile w/ Pinholes & Divots; Lobby-NW Area 20104203-1

Layer 1 White Ceiling Tile Homogeneity:Good

Not Detected 60% Cellulose 20% Mineral Wool 20% Non-Fibrous Material

08-CT4-27. 2'x4' White Ceiling Tile w/ Pinholes & Divots; Lobby-SE Area 20104204-1

Layer 1 White Ceiling Tile Homogeneity:Good

Not Detected 60% Cellulose

08-CT4-28. 2'x4' White Ceiling Tile w/ Pinholes & Divots; Dining Room- Central Area 20104205-1

Layer 1 White Ceiling Tile Homogeneity:Good

Not Detected 60% Cellulose

09-CT4-29. 2'x4' White Ceiling Tile w/ Pinholes & Scratches; Dining Room- South--Central Area 20104206-1

Layer 1 White Ceiling Tile Homogeneity:Good

Not Detected 60% Cellulose

EMLab ID: 4036622, Page 7 of 21Eurofins Built Environment Testing East, LLC

The total percentage of sample components shown may be greater than 100% when some components are detected at <1%.

The test report shall not be reproduced except in full, without written approval of the laboratory. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. The Company reserves the right to dispose of all samples after a period of thirty (30) days, according to all state and federal guidelines, unless otherwise specified.

Inhomogeneous samples are separated into homogeneous subsamples and analyzed individually. ND means no fibers of that type were detected.

When detected, the minimum detection and reporting limit is less than 1% unless point counting is performed. Floor tile samples may contain large amounts of interference material and it is recommended that the sample be analyzed by gravimetric point count analysis to lower the detection limit and to aid in asbestos identification.

‡ A "Version" indicated by -"x" after the Lab ID# with a value greater than 1 indicates a sample with amended data. The revision number is

(856) 231-9449 www.eurofinsus.com/Built Client: Terracon Consultants- Lenexa C/O: Ryan Slanczka Re: 02237230 - 2004 E. Santa Fe St

Date of Receipt: 04-18-2025 Date of Report: 10-15-2025

Bulk Asbestos Fiber Analysis by Polarized Light Microscopy (PLM) Appx E Sub E 40 CFR 763 / EPA 600/R-93/116

Sample ID # Lab-ID version Sample Description Asbestos

Constituents Non-Asbestos Constituents Comment

09-CT4-30. 2'x4' White Ceiling Tile w/ Pinholes & Scratches; Lobby-NW Area 20104207-1

Layer 1 White Ceiling Tile Homogeneity:Good

Not Detected 60% Cellulose

09-CT4-31. 2'x4' White Ceiling Tile w/ Pinholes & Scratches; Lobby-SE Area 20104208-1

Layer 1 White Ceiling Tile Homogeneity:Good

Not Detected 60% Cellulose

10-CT4-32. 2'x4' White Ceiling Tile w/ Pinholes & Fissures; Dining Room- South Central Area 20104209-1

Layer 1 White Ceiling Tile Homogeneity:Good

Not Detected 60% Cellulose

10-CT4-33. 2'x4' White Ceiling Tile w/ Pinholes & Fissures;Dining Room- Sorth Central Area 20104210-1

Layer 1 White Ceiling Tile Homogeneity:Good

Not Detected 60% Cellulose

10-CT4-34. 2'x4' White Ceiling Tile w/ Pinholes & Fissures;Dining Room-SE Area 20104211-1

Layer 1 White Ceiling Tile Homogeneity:Good

Not Detected 60% Cellulose

11-CT4-35. 2'x4' White Gypsum Ceiling Tile; Kitchen-SE Area 20104212-1

Layer 1 Brown Ceiling Tile with White Surface Homogeneity:Good

Not Detected 81% Non-Fibrous Material

4% Glass Fibers

11-CT4-36. 2'x4' White Gypsum Ceiling Tile; Kitchen-NW Area 20104213-1

Layer 1 Brown Ceiling Tile with White Surface Homogeneity:Good

Not Detected 81% Non-Fibrous Material

11-CT4-37. 2'x4' White Gypsum Ceiling Tile; NE Storage Room-SW Area 20104214-1

Layer 1 Brown Ceiling Tile with White Surface Homogeneity:Good

Not Detected 81% Non-Fibrous Material

12-MA2-38. Concrete Block Mortar;

Kitchen-NE Area, West Wall 20104215-1

Layer 1 Gray Mortar Homogeneity:Good

Not Detected 100% Non-Fibrous Material

12-MA2-39. Concrete Block Mortar;

Kitchen-NE Area, East Wall 20104216-1

Layer 1 Gray Mortar Homogeneity:Good

Not Detected 100% Non-Fibrous Material

12-MA2-40. Concrete Block Mortar;

North Exterior-East Outer Wall 20104217-1

Layer 1 Gray Mortar Homogeneity:Good

Not Detected 100% Non-Fibrous Material

Comments:

EMLab ID: 4036622, Page 8 of 21Eurofins Built Environment Testing East, LLC

The total percentage of sample components shown may be greater than 100% when some components are detected at <1%.

The test report shall not be reproduced except in full, without written approval of the laboratory. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. The Company reserves the right to dispose of all samples after a period of thirty (30) days, according to all state and federal guidelines, unless otherwise specified.

Inhomogeneous samples are separated into homogeneous subsamples and analyzed individually. ND means no fibers of that type were detected.

When detected, the minimum detection and reporting limit is less than 1% unless point counting is performed. Floor tile samples may contain large amounts of interference material and it is recommended that the sample be analyzed by gravimetric point count analysis to lower the detection limit and to aid in asbestos identification.

‡ A "Version" indicated by -"x" after the Lab ID# with a value greater than 1 indicates a sample with amended data. The revision number is

(856) 231-9449 www.eurofinsus.com/Built Client: Terracon Consultants- Lenexa C/O: Ryan Slanczka Re: 02237230 - 2004 E. Santa Fe St

Date of Receipt: 04-18-2025 Date of Report: 10-15-2025

Bulk Asbestos Fiber Analysis by Polarized Light Microscopy (PLM) Appx E Sub E 40 CFR 763 / EPA 600/R-93/116

Sample ID # Lab-ID version Sample Description Asbestos

Constituents Non-Asbestos Constituents Comment

13-MA5-41. 4"x8" Faux-Wood Ceramic Floor Tile w/ Grout & Mortar;

Dining Room-SE Area 20104218-1(cont.)

Layer 1 Brown Ceramic Tile

Black Grout

Light Gray Mortar Homogeneity:Good

Not Detected 100% Non-Fibrous Material

13-MA5-42. 4"x8" Faux-Wood Ceramic Floor Tile w/ Grout & Mortar;

Playroom-North-Central Area 20104219-1

Layer 1 Brown Ceramic Tile

Homogeneity:Good

Not Detected 100% Non-Fibrous Material

13-MA5-43. 4"x8" Faux-Wood Ceramic Floor Tile w/ Grout & Mortar;

Lobby-NW Area 20104220-1

Layer 1 Brown Ceramic Tile

Homogeneity:Good

Not Detected 100% Non-Fibrous Material

Comments:

EMLab ID: 4036622, Page 9 of 21Eurofins Built Environment Testing East, LLC

The total percentage of sample components shown may be greater than 100% when some components are detected at <1%.

The test report shall not be reproduced except in full, without written approval of the laboratory. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. The Company reserves the right to dispose of all samples after a period of thirty (30) days, according to all state and federal guidelines, unless otherwise specified.

Inhomogeneous samples are separated into homogeneous subsamples and analyzed individually. ND means no fibers of that type were detected.

When detected, the minimum detection and reporting limit is less than 1% unless point counting is performed. Floor tile samples may contain large amounts of interference material and it is recommended that the sample be analyzed by gravimetric point count analysis to lower the detection limit and to aid in asbestos identification.

‡ A "Version" indicated by -"x" after the Lab ID# with a value greater than 1 indicates a sample with amended data. The revision number is

(856) 231-9449 www.eurofinsus.com/Built Client: Terracon Consultants- Lenexa C/O: Ryan Slanczka Re: 02237230 - 2004 E. Santa Fe St

Date of Receipt: 04-18-2025 Date of Report: 10-15-2025

Bulk Asbestos Fiber Analysis by Polarized Light Microscopy (PLM) Appx E Sub E 40 CFR 763 / EPA 600/R-93/116

Sample ID # Lab-ID version Sample Description Asbestos

Constituents Non-Asbestos Constituents Comment

14-MA5-44. 6"x6" Red/Dark Brown Ceramic Floor/Cove Base Tile w/ Grout & Mortar; Kitchen-West-Central Area, Floor 20104221-1(cont.)

Layer 1 Brown/ Red Ceramic Tile

Homogeneity:Good

Not Detected 100% Non-Fibrous Material

14-MA5-45. 6"x6" Red/Dark Brown Ceramic Floor/Cove Base Tile w/ Grout & Mortar; Kitchen-East-Central Area, Floor 20104222-1

Layer 1 Brown/ Red Ceramic Tile

Homogeneity:Good

Not Detected 100% Non-Fibrous Material

14-MA5-46. 6"x6" Red/Dark Brown Ceramic Floor/Cove Base Tile w/ Grout & Mortar; Kitchen-NW Room, West Wall, Cove Base 20104223-1

Layer 1 Brown/ Red Ceramic Tile

Homogeneity:Good

Not Detected 100% Non-Fibrous Material

Comments:

EMLab ID: 4036622, Page 10 of 21Eurofins Built Environment Testing East, LLC

The total percentage of sample components shown may be greater than 100% when some components are detected at <1%.

The test report shall not be reproduced except in full, without written approval of the laboratory. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. The Company reserves the right to dispose of all samples after a period of thirty (30) days, according to all state and federal guidelines, unless otherwise specified.

Inhomogeneous samples are separated into homogeneous subsamples and analyzed individually. ND means no fibers of that type were detected.

When detected, the minimum detection and reporting limit is less than 1% unless point counting is performed. Floor tile samples may contain large amounts of interference material and it is recommended that the sample be analyzed by gravimetric point count analysis to lower the detection limit and to aid in asbestos identification.

‡ A "Version" indicated by -"x" after the Lab ID# with a value greater than 1 indicates a sample with amended data. The revision number is

(856) 231-9449 www.eurofinsus.com/Built Client: Terracon Consultants- Lenexa C/O: Ryan Slanczka Re:…