36E77618R0051-00001007.pdf

1. THE ELECTRICAL DRAWINGS INDICATE EXISTING ELECTRICAL ITEMS TO BE REMOVED. THE

DRAWINGS ARE INTENDED TO INDICATE THE SCOPE OF WORK REQUIRED AND DO NOT

INDICATE EVERY BOX, CONDUIT, OR WIRE THAT MUST BE REMOVED. THE CONTRACTOR

SHALL VISIT THE SITE PRIOR TO SUBMITTING A BID AND VERIFY EXISTING CONDITIONS.

2. ELECTRICAL ITEMS (i.e., LIGHTING FIXTURES, RECEPTACLES, SWITCHES, ETC.) REMOVED AND

NOT RELOCATED REMAIN THE PROPERTY OF THE OWNER. THE CONTRACTOR SHALL BE

RESPONSIBLE FOR THE DISPOSAL OF MATERIAL THE OWNER DOES NOT WANT TO REUSE OR

RETAIN (i.e., FOR MAINTENANCE PURPOSES).

3. THE CONTRACTOR SHALL OBTAIN APPROVAL FROM THE OWNER BEFORE TURNING OFF

POWER TO CIRCUITS, FEEDERS, PANELS, ETC. COORDINATE ALL OUTAGES WITH OWNER.

CONDUIT CONCEALED IN WALL CONSTRUCTION MAY BE ABANDONED IN PLACE IF NOT

AFFECTED BY OTHER CONSTRUCTION.

4. WHERE LIGHTS, SWITCHES, RECEPTACLES, ETC., ARE BEING REMOVED ALL ASSOCIATED

CONDUIT AND WIRE BACK TO THE PANELBOARD OR FEEDER JUNCTION BOX SERVING THE

DEVICE SHALL ALSO BE REMOVED, UNLESS THE CONDUIT CAN BE REUSED FOR NEW

CONDUCTORS. UNLESS NOTED OTHERWISE.

5. ALL CONDUIT SHALL BE REMOVED WHERE WALLS ARE BEING REMOVED. WHERE CONDUIT IS

IN THE CONCRETE SLAB, CUT OFF FLUSH, PULL OUT WIRE, AND PLUG. WHERE CONDUIT IS

RUN EXPOSED, ALL ASSOCIATED CLAMPS, SUPPORTS, HANGERS, ETC., SHALL ALSO BE

REMOVED.

6. THIS CONTRACTOR SHALL COORDINATE ALL HIS WORK WITH OTHER CONTRACTORS AT THE

JOB SITE BEFORE REMOVING EXISTING ELECTRICAL AND INSTALLING NEW ITEMS.

7. EXISTING CONDUIT IN GOOD CONDITION, MAY BE REUSED IN PLACE. RELOCATED EXISTING

CONDUIT SHALL NOT BE ALLOWED. BONDING CONDUCTORS SHALL BE INSTALLED IN ALL

REUSED CONDUIT TO ASSURE PROPER GROUND PATH.

8. EQUIPMENT REMOVAL IN CERTAIN LOCATIONS MAY REQUIRE THE INSTALLATION OF A

JUNCTION BOX TO RECONNECT CIRCUITS THAT REMAIN IN OPERATION. EXTEND CONDUIT

AND WIRING AS REQUIRED TO MAINTAIN POWER TO REMAINING EQUIPMENT.

9. CONTRACTOR SHALL REMOVE AND INSTALL ALL CEILING TILES AS REQUIRED FOR THE

EXECUTION OF ELECTRICAL WORK THAT IS OUTSIDE THE CONTRACT LIMITS OF

CONSTRUCTION. CONTRACTOR SHALL REPLACE CEILING TILES WITH IDENTICAL MATERIAL

WHERE DAMAGED BY THIS CONTRACTOR.

10. BALLASTS MANUFACTURED PRIOR TO 1980 CONTAIN PCBs AND SHALL BE DISPOSED OF BY A

FEDERAL OR STATE E.P.A. APPROVED METHOD AND IN ACCORDANCE WITH SPECIFICATIONS.

11. FLUORESCENT LAMPS CONTAIN MERCURY AND SHALL BE DISPOSED OF BY A FEDERAL OR

STATE E.P.A. APPROVED METHOD AND IN ACCORDANCE WITH SPECIFICATIONS.

GENERAL ELECTRICAL NOTES:

1. "1/E-11" INDICATES DETAIL NUMBER/SHEET NUMBER.

2. "MS-1" INDICATES ELECTRICAL EQUIPMENT DEFINED IN ELECTRICAL SCHEDULES. REFER TO

DRAWINGS CONTAINING ELECTRICAL SCHEDULES FOR REQUIREMENTS. PERMANENT

NAMEPLATE SHALL MATCH FINAL EQUIPMENT NOMEMCLATURE, NOT THE ELECTRICAL

EQUIPMENT TAG NAME. REFER TO SPECIFICATIONS FOR ADDITIONAL INFORMATION

AND IDENTIFICATION REQUIREMENTS.

3. " # " INDICATES KEYED NOTE USED TO DESCRIBE ADDITIONAL INFORMATION OF WORK

REQUIRED, SPECIFIC TO THE SHEET AND/OR DETAIL IT IS SHOWN WITH.

5. ALL ELECTRICAL CONDUCTORS SHALL BE COPPER.

6. ABBREVIATION KEY:

E.C. ELECTRICAL CONTRACTOR

M.C. MECHANICAL CONTRACTOR

G.C. GENERAL CONTRACTOR

AFF ABOVE FINISH FLOOR

C CONDUIT

TYP TYPICAL

+##" MOUNTING HEIGHT FROM FINISHED FLOOR TO CENTERLINE

7. REFER TO MATERIAL LIST AND SPECIFICATIONS FOR FULL DESCRIPTIONS AND

MANUFACTURERS OF ALL DEVICES.

8. LINE TYPE KEY:

NEW WORK BY THIS CONTRACTOR (DARK SOLID LINE)

NEW WORK UNDERFLOOR OR UNDERGROUND BY THIS CONTRACTOR (DARK

LONG DASHED LINE)

NEW WORK BY OTHERS AND/OR EXISTING TO REMAIN (LIGHT SOLID LINE)

EXISTING TO BE REMOVED BY THIS CONTRACTOR (DARK SHORT DASHED

LINE)

ELECTRICAL INSTALLATION NOTES:

1. THE COMPLETE INSTALLATION SHALL BE IN ACCORDANCE WITH THE ADAAG (AMERICANS WITH

DISABILITIES ACT ACCESSIBILITY GUIDELINES).

2. NOT USED

3. A #12 GREEN INSULATED GROUND CONDUCTOR SHALL BE INSTALLED WITH CIRCUIT

CONDUCTORS TO ALL RECEPTACLES.

4. CONCEAL ALL CONDUIT IN WALLS, PARTITIONS AND ABOVE CEILING,ETC. UNLESS OTHERWISE INDICATED ON THE PLANS OR IN THE SPECIFICATIONS. CONDUIT IN MECHANICAL ROOMS, AND

STORAGE ROOMS WITHOUT CEILINGS MAY BE EXPOSED ON BUILDING STRUCTURE. INCREASE

CONDUCTOR SIZE IF POWER CONDUCTOR INCREASES DO TO VOLTAGE DROP.

5. CONTRACTOR SHALL VERIFY ALL EQUIPMENT LOCATIONS WITH EXISTING CONDITIONS. PRIOR TO

MAKING THE ACTUAL ELECTRICAL INSTALLATION THIS CONTRACTOR SHALL ADJUST

RECEPTACLES, OUTLETS OR CONNECTION LOCATIONS TO ACCOMMODATE FURNITURE AND/OR

EQUIPMENT.

6. ELECTRICAL EQUIPMENT SHALL BE MOUNTED TO AVOID IMPEDANCE OF, OPERATION OF, AND/OR

ACCESS TO ELECTRICAL AND MECHANICAL EQUIPMENT. ALL MOUNTING OF ELECTRICAL AND

TELECOMMUNICATIONS EQUIPMENT, ON EQUIPMENT SUPPLIED BY ANOTHER CONTRACTOR,

SHALL BE APPROVED IN ADVANCE BY THE OTHER CONTRACTOR.

7. ALL FINAL ELECTRICAL CONNECTIONS TO MOTORS SHALL BE MADE WITH FLEXIBLE METAL

CONDUIT. USE LIQUIDTIGHT CONDUIT AND FITTINGS WHERE SUBJECT TO MOISTURE. ROUTE

GROUND WIRE FROM CIRCUIT GROUND TO MOTOR GROUND THROUGH FLEXIBLE CONDUIT.

FLEXIBLE CONDUIT SHALL NOT EXCEED 6' IN LENGTH.

8. CONTRACTOR SHALL BE RESPONSIBLE FOR ALL OPENINGS REQUIRED IN WALLS. ALL OPENINGS

SHALL BE REPAIRED TO MATCH EXISTING BY A QUALIFIED CONTRACTOR AT THE EXPENSE OF

THIS CONTRACTOR. ALL CONDUITS THROUGH WALLS SHALL BE GROUTED OR SEALED INTO

OPENINGS.

9. ALL MATERIALS USED TO SEAL PENETRATIONS OF FIRE RATED WALLS AND FLOORS SHALL BE

TESTED AND CERTIFIED AS A SYSTEM PER ASTM E814 STANDARDS FOR FIRE TESTS OF

THROUGH-PENETRATION FIRESTOPS.

10. CONTRACTOR SHALL REMOVE AND REINSTALL ALL CEILING TILES AS REQUIRED FOR THE

EXECUTION OF ELECTRICAL WORK THAT IS OUTSIDE THE CONTRACT LIMITS OF CONSTRUCTION.

CONTRACTOR SHALL REPLACE CEILING TILES WITH IDENTICAL MATERIAL WHERE DAMAGED BY

THIS CONTRACTOR.

GENERAL ELECTRICAL EQUIPMENT SCHEDULE

ELECTRICAL LIGHTING SYMBOL LIST

ELECTRICAL POWER SYMBOL LIST

ELECTRICAL SYSTEMS SYMBOL LIST

EX. EXISTING

ELECTRICAL DEMOLITION NOTES:

The FUTURE.

Built SMARTER.®

SUB-BASEMENT FLOOR PLAN - ELECTRICAL DEMOLITION

R T HN O

BE FLOOR PLAN - ELECTRICAL DEMOLITION

BS FLOOR PLAN - ELECTRICAL DEMOLITION

BW FLOOR PLAN - ELECTRICAL DEMOLITION

1E FLOOR PLAN - ELECTRICAL DEMOLITION

3S FLOOR PLAN - ELECTRICAL DEMOLITION

5S FLOOR PLAN - ELECTRICAL DEMOLITION

GENERAL NOTES

KEYNOTES

8W FLOOR PLAN - ELECTRICAL DEMOLITION

R T HN O

11W PENTHOUSE - ELECTRICAL DEMOLITION

8W FLOOR PLAN - LIGHTING

R T HN O

SUB-BASEMENT FLOOR PLAN - POWER & SYSTEMS

BS FLOOR PLAN - POWER & SYSTEMS

1E FLOOR PLAN - POWER & SYSTEMS

5S FLOOR PLAN - POWER & SYSTEMS

8W FLOOR PLAN - POWER & SYSTEMS

R T HN O

11W PENTHOUSE PLAN - POWER & SYSTEMS

R T HN O

PUMP CONNECTION DETAIL

NO SCALE1

DISCONNECT AND STARTER SCHEDULE

REMARKS:

STARTER TYPE: SA - STANDARD ACCESSORIES (INCLUDES * ITEMS)

FV - FULL VOLTAGE *CT - CONTROL TRANSFORMER,

FUSED 120V

PF - PHASE FAILURE RELAY

(5 HP OR GREATER) YD - WYE - DELTA

RE - REVERSING *EO - ELECTRONIC OVERLOAD TO - MELTING THERMAL OVERLOADS

TW - 2 SPEED, 2 WINDING *HA - HAND-OFF-AUTO IN DOOR TS - 2 SPEED SELECTOR SWITCH IN DOOR

SW - 2 SPEED, 1 WINDING *RP - RED (RUN) PILOT LIGHT IN

DOOR

GP - GREEN (OFF) PILOT LIGHT IN DOOR

RV - REDUCED VOLTAGE AUTOXFMR FA - 4-CONVERTIBLE AUXILIARY CONTACTS

SS - SOLID STATE *TA - TWO CONVERTIBLE

AUXILIARY CONTACTS

EI - ELECTRICAL INTERLOCK (2)-N.O.& (2)-N.C

MD - MOTOR DISCONNECT SWITCH SS - START-STOP PUSHBUTTON IN DOOR

MS - MANUAL STARTER S/N - INSULATED NEUTRAL

ASSEMBLY

HL - HANDLE PADLOCK HASP

MX - MANUAL SWITCH

FDS - FUSED SWITCH

DISCONNECT TYPE & RATING STARTER

ITEM FUSED

NON-

FUSED

CIRCUIT

BREAKER VOLTAGE POLES

NEMA

SIZE TYPE

NEMA

ENCLOSURE REMARKS APPROVED MANUFACTURERS

MS-1 120 1 MS 1 RP, TO SQUARE D 2510 FG1P

CUTLER-HAMMER TYPE MS

GENERAL ELECTRIC CR101

SIEMENS TYPE SMF

LUMINAIRE SCHEDULE

(MTG) MOUNTING: (Type) LAMP TECHNOLOGY: (L/L) LENS/LOUVER:

RE - RECESSED FL - FLUORESCENT A- .125" ACRYLIC

SP - SUSPENDED CF - COMPACT FLUORESCENT B- BLACK BAFFLE

CL - CEILING SURFACE HL - HALOGEN C- CLEAR ALZAK

WL - WALL IN - INCANDESCENT D- PARABOLIC

UC - UNDER CABINET LED - LIGHT EMITTING DIODE F- FRESNEL

CV - COVE HS - HIGH PRESSURE SODIUM G- TEMPERED GLASS

PL - POLE MH - METAL HALIDE H- WALL WASHER

FR- FLANGED RECESSED SMH - SUPER METAL HALIDE P- POLY CARBONATE

O - OTHER ( SEE DESCRIPTION) PSMH - PULSE START METAL HALIDE K- KSH12 .125" ACRYLIC

DOOR: CMH - CERAMIC METAL HALIDE K19- KSH19 .156" ACRYLIC

FA - FLAT ALUMINUM O - OTHER (SEE DESCRIPTION) L- LOW IRIDESCENT SPECULAR ALUM.

FS - FLAT STEEL XL - EXTENDED LIFE N- NONE

RA - REGRESSED ALUMINUM XLP - EXTENDED LIFE & OUTPUT R- HIGH IMPACT DR ACRYLIC

RS - REGRESSED STEEL O- OTHER (SEE DESCRIPTION)

(TYPE) BALLAST: (TYPE) BALLAST:

FINISH: DIM07- LINE DIMMING BALLAST EB- ELECTRONIC BALLAST

PAF - PAINT AFTER FABRICATION DIM10- 0-10V DIMMING BALLAST EM- EMERGENCY BATTERY/BALLAST CSA - FINISH SELECTION BY ARCHITECT HL- HIGH / LOW LEVEL BALLAST DALI- DIGITAL DIMMING BALLAST

ML- MULTI-LEVEL SWITCHING MV- MULTI-VOLTAGE ELECTRONIC 120V-277V

HP- HIGH PERFORMANCE / LBF #BF- BALLAST FACTOR

CATALOG NUMBER SHALL NOT BE CONSIDERED COMPLETE AND MATERIAL SHALL NOT BE ORDERED BY MANUFACTURER AND CATALOG NUMBER ONLY. THE COMPLETE DESCRIPTION AND THE SPECIFICATION SHALL BE COORDINATED WITH THE CATALOG NUMBER TO DETERMINE THE EXACT MATERIAL AND ACCESSORIES TO BE ORDERED. THE FIRST MANUFACTURER LISTED IS THE

BASIS FOR DESIGN.

REFER TO SPECIFICATION SECTION LIGHTING 26 51 00 FOR ADDITIONAL INFORMATION AND REQUIREMENTS.

ALL LAMPS FOR THIS PROJECT SHALL BE FURNISHED AND INSTALLED BY THE ELECTRICAL CONTRACTOR UNLESS OTHERWISE NOTED.

FLUORESCENT LAMP CORRELATED COLOR TEMPERATURE 4100°K, COLOR RENDERING INDEX (CRI) AT OR ABOVE 80, UNLESS NOTED OTHERWISE.

LED LAMP COLOR RENDERING INDEX (CRI) AT OR ABOVE 85 FOR INTERIOR APPLICATIONS.

ITEM DESCRIPTION

DIMENSIONS LAMPS BALLAST

L/LL W H DIA MTG TYPE QTY MODEL VOLTS TYPE

APPROVED

MANUFACTURER

F1 RECESSED DIRECT WITH HIGH ANGLE

ILLUMINANCE, MATTE ACRYLIC DIFFUSER, TWO

PARALLEL LAMP CHAMBERS.

24" 24" 4.5" RE LED MAX 40

WATT

MINIMUM

4000 LUMEN

MV O LITHONIA VT LED

OR EQUAL BY DAYBRITE OR

COLUMBIA

C.7C.7

EXISTING

WAREHOUSE

1C04B

LIQUID

NITROGEN

STORAGE

114H

MEETING

ROOM

RECEPTION/

WAITING/

FINGER

PRINT

114G

TRAINING

ROOM 1C04A

ELECTRICAL

114E

OFFICE,

LEAD

SUPER

114D

OFFICE,

CHIEF

114C

OFFICE,

ASST.

CHIEF

114B

OFFICE,

LEAD

SPECIALIST

114A

OFFICE,

LEAD

SPECIALIST

HUMAN

RESOURCES

113A

OFFICE,

PIV

COORD

1C03

CORRIDOR

BCS04

CORRIDOR

1C02

LOBBY

Q

9A

9A

G.1

3.1 5.84.64.2 5.4

J

B

1C01

VESTIBULE

MECHANICAL

EQUIPMENT

ROOM

130A

ELECTRICAL

EQUIPMENT

ROOM

BS11

IV

STORAGE

BS12

WOMEN'S

TOILET

BS14

MEN'S

TOILET

BS13

UNIV

WASTE

HOLDING

BCS05

CORRIDOR

SAFETY

EQUIPMENT

STORAGE

IT

CLOSET

ELEV.

EQUIP.

ROOM109

ELEC

CLST

P-1

ELEVATOR

BREAKROOM

HSKPG

1ST02

EGRESS

STAIR

114F

OFFICE,

LEAD

SUPER

1C04

RECEIVING

A

A2

A4

A6

C

DD

EE

FF

GG

HH

UP

UP

DN

DN

DN

BLD. 2 FIRST FLOOR PLAN - ELECTRICAL DEMOLITION

R T HN O

C.7C.7

EXISTING

WAREHOUSE

1C04B

LIQUID

NITROGEN

STORAGE

114H

MEETING

ROOM

RECEPTION/

WAITING/

FINGER

PRINT

114G

TRAINING

ROOM 1C04A

ELECTRICAL

114E

OFFICE,

LEAD

SUPER

114D

OFFICE,

CHIEF

114C

OFFICE,

ASST.

CHIEF

114B

OFFICE,

LEAD

SPECIALIST

114A

OFFICE,

LEAD

SPECIALIST

HUMAN

RESOURCES

113A

OFFICE,

PIV

COORD

1C03

CORRIDOR

BCS04

CORRIDOR

1C02

LOBBY

Q

9A

9A

G.1

3.1 5.84.64.2 5.4

J

B

1C01

VESTIBULE

MECHANICAL

EQUIPMENT

ROOM

130A

ELECTRICAL

EQUIPMENT

ROOM

BS11

IV

STORAGE

BS12

WOMEN'S

TOILET

BS14

MEN'S

TOILET

BS13

UNIV

WASTE

HOLDING

BCS05

CORRIDOR

SAFETY

EQUIPMENT

STORAGE

IT

CLOSET

ELEV.

EQUIP.

ROOM109

ELEC

CLST

P-1

ELEVATOR

BREAKROOM

HSKPG

1ST02

EGRESS

STAIR

114F

OFFICE,

LEAD

SUPER

1C04

RECEIVING

A

A2

A4

A6

C

DD

EE

FF

GG

HH

UP

UP

DN

DN

DN

BLD. 2 FIRST FLOOR PLAN - POWER & SYSTEMS

R T HN O

BLD. 7 FIRST FLOOR PLAN - ELECTRICAL DEMOLITION