105126.18 Solid Plastic Lockers (3).pdf

OKC Renovate B Mod for PACT Project Number 635-19-101

RFI #1 1.24.22

VA 05-01-20

105126.18 - 1

SECTION 105126.18

SOLID PLASTIC LOCKERS

PART GENERAL

1.1 SUMMARY

A. Section includes:

1. Solid plastic lockers.

B. Related Sections:

1. Division 01: Administrative, procedural, and temporary work requirements.

2. Division 06: Rough carpentry.

C. References

1. UL – GREENGUARD certified low emitting materials.

2. ASTM - B221 - Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes.

3. ASTM – A167 - Standard Specification for Stainless and Heat-Resisting Chromium-Nickel

Steel Plate, Sheet, and Strip.

1.2 SUBMITTALS

A. Submittals for Review:

1. Shop Drawings: Include dimensioned layouts, elevations, trim, closures and accessories.

2. Product Data: Manufacturer’s descriptive data

3. Samples: 3 x 3 inch samples showing available colors.

1.3 QUALITY ASSURANCE

A. Manufacturer Qualifications: Minimum 5 years of experience in manufacture of solid plastic lockers with products in satisfactory use under similar service conditions.

B. Installer Qualifications: Minimum 5 years of experience in work of this Section. The installer must be a certified installer through manufacturer’s installation certification program.

1.4 DELIVERY, STORAGE, AND HANDLING

A. Store in an upright condition. Protect plastic lockers from exposure to direct sunlight. This product is not intended for outdoor use.

105126.18 - 2

1.5. WARRANTY

A. Provide manufacturer’s 25 year warranty against breakage, corrosion, and delamination under normal conditions.

PART 2 PRODUCTS

2.1 MANUFACTURERS

A. Basis of Design: Contract documents are based on products by Scranton Products.

(www.scrantonproducts.com) OR VA Approved Equal.

B. Substitutions: Equal product substitutions are allowed, but the burden of proof of equality will be the responsibility of the General Contractor.

C. Materials

1. High Density Polyethylene (HDPE): polyethylene thermoplastic formed into solid plastic components with homogeneous color throughout, with smooth orange peel finish.

2. Heavy Duty Extruded Aluminum: B221, 6063-T6

3. Chromium Plated Steel: A167

4. Color: To be selected from manufacturer’s color range.

2.2 STANDARD PLASTIC LOCKERS

A. Locker Configuration: Two tier

B. Locker Dimensions:

1. Height, Nominal: 36 inch (two 36 inch lockers stacked)

2. Width: 12 inch

3. Depth: 18 inch

C. Locker Locations:

1. Lockers are located in the Staff Locker room GF125.

D. Material: High density polyethylene (HDPE) plastic

. Sides, Tops, Bottoms, Backs, and Shelves: 3/8 inch thick HDPE plastic, grey finish.

1. Sides: 3/8 inch thick HDPE plastic, grey finish

F. Locker Tops: Flat top finished in same color as locker door (recessed in wall)

G. Doors and Frame: ½ inch thick HDPE plastic

1. Doors: ½ inch thick HDPE plastic with horizontal venting

2. Handle: ADA compliant ergonomic handle, injection molded plastic http://www.scrantonproducts.com/

105126.18 - 3

3. Locks: In-door key

4. Hinge: Heavy duty extruded aluminum with corrosion free stainless steel pin with silver finish.

5. Engraving: none

6. ADA Compliance Package: 3134 aluminum Series 1100, H18, satin matte finish ADA plaque, adjustable 3/8 inch HDPE plastic shelf with plastic clips

7. Latch Bar: 3/8 inch thick HDPE plastic with multiple latch points, fastened with stainless steel tamper-resistant screws

H. Assembly profile: Full height of lockers, PVC plastic, snap fit assembled onto locker sides.

I. Accessories

1. Coat hook: Two-prong, high impact plastic, black finish, mounted to side of divider, two per door opening.

2. End Panels: 1 inch thick HDPE plastic, color and finish same as locker door

3. Filler Panels and Trim: ½ inch thick HDPE plastic, color and finish same as locker door

4. Number Plate: 3134 aluminum, Series 1100, H18, satin matte finish, fastened to locker with corrosion resistant stainless steel rivets

5. Locker Base: 1 inch thick HDPE plastic, with color and finish same as locker door, 4 inch; field assembly required.

6. Wall hook: two per door opening.

7. Garment Bar: heavy duty extruded aluminum

8. Color: As selected by VA from manufacturer’s color range.

2.8 FABRICATION

A. Fabricate locker components square and rigid; finish free from scratches and chips.

B. Fabricate locker components for snap-together assembly or slide-together dovetail connections providing solid and secure, anti-racking construction.

C. Fabricate adjacent lockers with common side panel.

D. Fabricate locker units for assembly in maximum of three adjacent lockers.

E. Fabricate locker benches to sizes indicated in single lengths.

PART 3 EXECUTION

3.1 INSTALLATION

A. Install lockers in accordance with manufacturer’s instructions and approved Shop Drawings.

B. Set lockers on prepared locker base.

C. Set plumb, level, rigid, and aligned.

105126.18 - 4

D. Attach lockers to supporting construction with anchors best suited to substrate conditions.

3.2 ADJUSTING

A. Adjust doors and latches to operate correctly.

END OF SECTION