Attachment - Door Hardware.pdf

Correct FCA Deficiencies in Boiler Plant, Building 14 04-01-20

Central Alabama Veterans Health Care System

08 71 00-1

SECTION 08 71 00

DOOR HARDWARE

PART 1 - GENERAL

1.1 DESCRIPTION

A. Door hardware and related items necessary for complete installation and operation of doors.

1.2 RELATED WORK

A. Caulking: Section 07 92 00 JOINT SEALANTS.

B. Application of Hardware: Section 08 11 13, HOLLOW METAL DOORS AND

FRAMES; and Section 32 31 33, CHAIN LINK FENCES AND GATES.

C. Painting: Section 09 91 00, PAINTING.

D. Electrical: Division 26, ELECTRICAL.

1.3 GENERAL

A. All hardware shall comply with ABAAS, (Architectural Barriers Act

Accessibility Standard) unless specified otherwise.

B. Provide rated door hardware assemblies where required by most current version of the International Building Code (IBC).

C. Hardware for Labeled Fire Doors and Exit Doors: Conform to requirements of NFPA 80 for labeled fire doors and to NFPA 101 for exit doors, as well as to other requirements specified. Provide hardware listed by UL, except where heavier materials, large size, or better grades are specified herein under paragraph HARDWARE SETS. In lieu of UL labeling and listing, test reports from a nationally recognized testing agency may be submitted showing that hardware has been tested in accordance with UL test methods and that it conforms to NFPA requirements.

D. Hardware for application on metal and wood doors and frames shall be made to standard templates. Furnish templates to the fabricator of these items in sufficient time so as not to delay the construction.

E. The following items shall be of the same manufacturer, except as otherwise specified:

1. Mortise locksets.

2. Hinges for hollow metal and wood doors.

3. Surface applied overhead door closers.

4. Exit devices.

5. Floor closers.

08 71 00-17

4. Submit written report identifying problems.

3.4 DEMONSTRATION

A. Demonstrate efficacy of mechanical hardware and electrical, and electronic hardware systems, including adjustment and maintenance procedures, to satisfaction of Resident/Project Engineer and VA

Locksmith.

3.5 HARDWARE SETS

A. Following sets of hardware correspond to hardware symbols shown on drawings. Only those hardware sets that are shown on drawings will be required. Disregard hardware sets listed in specifications but not shown on drawings.

B. Hardware Consultant working on a project will be responsible for providing additional information regarding these hardware sets. The numbers shown in the following sets come from BHMA standards.

INTERIOR SINGLE DOORS

HW-2D

Each Door to Have: RATED

Hinges QUANTITY & TYPE AS REQUIRED

1 Privacy Lock F02-MOD X OCCUPANCY INDICATOR

1 Closer C02011/C02021

1 Kick Plate J102

1 Mop Plate (@ Inswing Doors) J103

1 Wall Stop L02101 CONVEX

1 Set Self-Adhesive Seals R0Y154

STONE THRESHOLD BY OTHER TRADES.

ELECTRIC HARDWARE ABBREVIATIONS LEGEND:

ADO = Automatic Door Operator

EMCH = Electro-Mechanical Closer-Holder

MHO = Magnetic Hold-Open (wall- or floor-mounted)

08 71 00-18

HW-2G

Each Door to Have: RATED/NON-RATED

1 Keyed Privacy Indicator Lock F13 x OCCUPANCY INDICATOR

1 Closer C02011/C02021

1 Kick Plate J102

1 Mop Plate (@ Inswing Doors) J103

1 Floor Stop L02121 x 3 FASTENERS

1 Auto Door Bottom R0Y346 – HEAVY DUTY

2 Set Self-Adhesive Seals R0Y154

STONE THRESHOLD BY OTHER TRADES.

HW-3B

Each Door to Have: NON-RATED/RATED

1 Office Lock F04

1 Closer C02011/C02021

1 Floor Stop L02121 x 3 FASTENERS

1 Door Viewer L03221 – 190° (VIEW INTO CORRIDOR)

1 Set Self-Adhesive Seals R0Y154

08 71 00-19

INTERIOR PAIRS OF DOORS – NOT USED

EXTERIOR SINGLE DOORS – NOT USED

EXTERIOR PAIRS OF DOORS

HW-E6

Each Pair to Have: NON-RATED

2 Continuous Hinge

1 Set Auto Flush Bolts TYPE 25

1 Dust Proof Strike L04021

1 Entry Lock F11

1 Overlapping Astragal with R0Y634 x R0Y154 x THRU-BOLTS

Self-Adhesive Seal

1 Coordinator TYPE 21A

2 Closer C02011/C02021

2 Kick Plate J102

2 Floor Stop L02121 x 3 FASTNERS

1 Threshold (outswing door) J32120 x SILICONE GASKET

1 Threshold (inswing door) ALUMINUM, PER ARCHITECTURAL DETAIL

2 Door Sweep R0Y416

1 Set Frame Seals R0Y164

1 Drip R0Y976

EXTERIOR SINGLE GATES

HW-G4

Each Gate to Have: NON-RATED

2 Weldable Gate Hinges A8181 (3 KNUCKLE) X 5 INCHES X WELDED OR

FASTENED X SHEAR HINGE LEAVES TO FIT

GATE MEMBERS

1 Weldable Panic Box

1 Anti-Vandal Pull

1 Rim Panic Device TYPE 1 F03 LESS TRIM

1 Cylinder TYPE AS REQUIRED

1 Stainless Steel Closer C52011/C22021

BALANCE OF HARDWARE BY SECTION 32 31 53, PERIMETER SECURITY FENCES AND

GATES

08 71 00-20

EXTERIOR PAIRS OF GATES

HW-G7

Each Pair Gates to Have: NON-RATED

4 Weldable Gate Hinges A8181 (3 KNUCKLE) X 5 INCHES X WELDED OR

FASTENED X SHEAR HINGE LEAVES TO FIT

GATE MEMBERS

2 Padlockable Cane Bolts

2 Padlocks TYPE AS REQUIRED

1 Weldable Lock Box

1 Utility Lock F09 X NON-FERROUS LOCK CASE

2 Stainless Steel Closer C52011/C22021

BALANCE OF HARDWARE BY SECTION 32 31 53, PERIMETER SECURITY FENCES AND

GATES. INSTALL CANE BOLTS ON PULL SIDE OF EACH LEAF. ACTIVE LEAF CANE BOLT

TO HAVE STRIKE IN OPEN POSITION ONLY. INACTIVE LEAF CANE BOLT TO HAVE

STRIKES IN BOTH OPEN AND CLOSED POSITIONS.

HW-G10

Each Rolling or Swing-Up Gate to Have: NON-RATED

1 Padlock or 2 Cylinders TYPE AS REQUIRED

BALANCE OF HARDWARE BY SECTION 32 31 53, PERIMETER SECURITY FENCES AND

GATES.

RESIDENTIAL UNIT PAIRS OF DOORS – NOT USED

INTERIOR SINGLE SECURITY DOORS – NOT USED

INTERIOR PAIRS OF SECURITY DOORS – NOT USED

EXTERIOR SINGLE SECURITY DOORS – NOT USED

MENTAL HEALTH AREAS – NOT USED

- - - E N D - - -

ROOM FINISH SCHEDULE GENERAL NOTES:

A. IN AREAS OUTSIDE THE PROJECT SCOPE WHERE EXISTING FINISHES WILL BE AFFECTED, CONTRACTOR SHALL

PATCH , REPAIR AND FINISH WITH MATCHING MATERIALS.

B. ALL EXISTING AND NEW WALL AND CEILING SURFACES SHALL BE PAINTED UNLESS NOTED OTHERWISE.

C. ALL FINISH SELECTIONS AND COLOR TO BE APPROVED BY COR AND VA INTERIOR DESIGNER.

D. PAINT ALL EXISTING AND NEW DOORS.

EQUIPMENT SCHEDULE GENERAL NOTES:

A. REFER TO INTERIOR ELEVATIONS DRAWINGS FOR SIZE AND LOCATIONS OF MANUFACTURED WOOD CASEWORK.

B. FINISH COLOR SELECTIONS AND THEIR LOCATIONS TO BE VERIFIED AND APPROVED BY COR.

C. REFER TO DRAWING G002 FOR MOUNTING HEIGHTS.

A

SEE SCHED

S E

E S

C H

E D

U

LE

DOOR TYPES

NTS

FRAME TYPES

NTS

S E

E S

C H

E D

U

LE

2" SEE SCHED

2"

2"

STRUCTURAL DECK

BACKER ROD AND

ACOUSTICAL SEALANT,

BOTH SIDES

CEILING PER FINISH

SCHEDULE

4" MTL

STUDS

GC4

6" MTL

STUDS

GC6

GC

ACOUSTICAL INSULATION

STC 45

STRUCTURAL DECK

BACKER ROD AND

ACOUSTICAL SEALANT,

BOTH SIDES

CEILING PER FINISH

SCHEDULE

20 GA MTL STUDS @ 16"

OC

5/8" TYPE "X" GWB, ONE

SIDE (CBB AT TILE FINISH)

BASE AND FLOOR FINISH

PER SCHEDULE

BACKER ROD AND

ACOUSTICAL SEALANT,

BOTH SIDES

SET RUNNERS ON

SEALANT, TYP

GK

2-1/2" MTL

STUDS

GK2

EXISTING OR ADJACENT

WALL, WHERE

APPLICABLE

20 GA MTL STUDS @ 16"

OC

5/8" TYPE "X" GWB, BOTH

SIDES (CBB AT TILE

FINISH)

BASE AND FLOOR FINISH

PER SCHEDULE

BACKER ROD AND

ACOUSTICAL SEALANT,

BOTH SIDES

SET RUNNERS ON

SEALANT, TYP

4" MTL

STUDS

GK4

HEAD DETAIL

SCALE: 3"=1'-0"

H2

JAMB DETAIL

SCALE: 3"=1'-0"

J2

SILL DETAIL

SCALE: 3"=1'-0"

S2

STEEL LINTEL

AND PLATE, PAINT

PERIMETER

SEALANT, EACH SIDE

HM FRAME

ANCHORED TO

STEEL PLATE

HM FRAME

ANCHORED TO

STEEL PLATE

PERIMETER

SEALANT, EACH SIDE

REMOVE EXISTING LOAD

BEARING MASONRY WALL

AS NEEDED TO INSTALL

NEW WORK

CONT. STEEL

PLATE, PAINT

CONT SEALANT

CONT SEALANT

EACH SIDE

FV

1'-0 1/2"

1"

1"

FV

1'-0 1/2"

REMOVE EXISTING LOAD

BEARING MASONRY WALL

AS NEEDED TO INSTALL

NEW WORK.

EXISTING FOUNDATION

WALL TO REMAIN

8"

THRESHOLD AS REQUIRED

DOOR PER SCHEDULE

FRAME PER SCHEDULE

FRAME PER SCHEDULE

DOOR PER SCHEDULE

TRANSITION STRIP AS

REQUIRED

FLOOR FINISH PER

SCHEDULE

PARTITION PER TYPE

SEALANT, EACH SIDE

FRAME PER SCHEDULE

DOOR PER SCHEDULE

DOUBLE METAL TRACK

PARTITION PER

TYPE

SEALANT, EACH SIDE

FRAME PER SCHEDULE

DOOR PER SCHEDULE

DOUBLE METAL STUD

JAMB ANCHOR

SILL DETAIL

SCALE: 3"=1'-0"

S1

JAMB DETAIL

SCALE: 3"=1'-0"

J1

HEAD DETAIL

SCALE: 3"=1'-0"

H1

5/8" GWB, TYP

STEEL TUBE AND BASE PLATE,

SEE STRUCTURAL

10"

6"

2 1/2" METAL STUD AT EDGE OF

BASE PLATE, EACH SIDE.

4" METAL STUD PARTITION PER TYPE.

SCHEDULED DOOR AND FRAME

EXISTING MASONRY WALL

A

5/8" GWB, TYP

STEEL TUBE AND BASE PLATE,

SEE STRUCTURAL

2 1/2" METAL STUD AT EDGE OF

BASE PLATE, EACH SIDE.

4" METAL STUD PARTITION PER TYPE.

EXISTING MASONRY WALL

4" METAL STUD AT EDGE OF BASE

PLATE, EACH SIDE.

6"

10"

VA FORM 08-6231

1 2 3 4 5 6 7 8 9

Date:

Drawing Title:

Approved Project Director

Project Title:

BID DOCUMENTS

590 MEANS ST NW

Phase Project Number

Building Number

Drawing NumberLocation

Issue Date CheckedFULLY SPRINKLERED

STAMP

STE. 200

ATLANTA, GA 30318

ARCHITECT/ENGINEER OF RECORDCONSULTANT

A

B

C

D

E

F

U.S. Department of Veterans Affairs

Office of Construction and

Facilities Management

Drawn

YK/AW/SJ/

DB

JH

DOOR & PARTITION TYPES,

SCHEDULES & DETAILS

CORRECT FCA DEFICIENCIES IN

BOILER PLANT, BUILDING 14

MONTGOMERY, AL

A601

619-20-103

09-20-2023

DOOR & FRAME SCHEDULE

DOOR

NO. WIDTH HEIGHT

DOOR

TYPE

DOOR

MATERIAL

FRAME

TYPE

FRAME

MATERIAL

HEAD

DETAIL

JAMB

DETAIL

SILL

DETAIL

FIRE

RATING

HARDWARE

SET REMARKS

201 3'-0" 7'-0" A HM 1 HM H1 J1 S1 --

202 3'-0" 7'-0" A HM 1 HM H1 J1 S1 --

202A 3'-0" 7'-0" A HM 1 HM H1 J1 S1 --

204 6'-0" 8'-6" A HM 1 HM H2 J2 S2 -- PAIRED DOOR

205 3'-0" 7'-0" A HM 1 HM H1 J1 S1 --

206 3'-0" 7'-0" A HM 1 HM H2 (SIM) J2 (SIM) S2 (SIM) --

REVISION 1 4-8-2020

EQUIPMENT SCHEDULE

JSN DESCRIPTION PROVIDED BY INSTALLED BY

A1030 TWO PERSON LOCKER, DOUBLE TIER, 72HX12WX18D. THIS

UNIT INCLUDES HOOKS FOR COATS AND HATS. DOOR

EQUIPPED WITH SAFETY GUARD HANDLES. DESIGNED

FOR STORAGE OF COATS, HATS, AND OTHER PERSONAL

BELONGINGS. OTHER WIDTH AND DEPTHS ARE

AVAILABLE.

GOVERNMENT CONTRACTOR

A1070 MIRROR, FLOAT GLASS, WITH SS FRAME, 24 X 36 CONTRACTOR CONTRACTOR

A5075 DISPOSABLE SOAP DISPENSER; SURFACE MOUNTED,

HIGH-IMPACT TOUCH FREE ABS PLASTIC WITH ONE

HANDED DISPENSING OPERATION WITH 800 ML CAPACITY;

FOAM OR LIQUID.

CONTRACTOR CONTRACTOR

A5082 DISPENSER, PAPER TOWEL, SENSOR, HANDS FREE CONTRACTOR CONTRACTOR

A5090 A SURFACE MOUNTED, SATIN FINISH STAINLESS STEEL,

SANITARY NAPKIN DISPOSAL. DISPOSAL FEATURES A

FLIP-UP COVER, SECURED TO THE CONTAINER BY A

HEAVY-DUTY STAINLESS-STEEL PIANO-HINGE.

CONTRACTOR CONTRACTOR

A5109 GRAB BAR, ABA COMPLIANT, SS, 2-WALL, W/C

ACCESSIBLE

CONTRACTOR CONTRACTOR

A5135 A SURFACE MOUNTED, SATIN FINISH STAINLESS STEEL,

UTILITY SHELF WITH A MAXIMUM OF 6 MOP/BROOM

HOLDERS AND 5 RAG HOOKS. FOR USE IN JANITOR

CLOSETS

FOR USE IN JANITOR CLOSETS

CONTRACTOR CONTRACTOR

A5202 A CONCEALED SURFACE MOUNTED, DOUBLE ROLL, SATIN

FINISH STAINLESS STEEL, COMBINATION TOILET TISSUE

DISPENSER AND UTILITY SHELF (MINIMUM 5" DEPTH). UNIT

ACCOMMODATES TWO STANDARD-CORE TOILET TISSUE

ROLLS THROUGH 6" IN DIAMETER. SPINDLES ARE

CHROME PLATED PLASTIC WITH A HEAVY-DUTY INTERNAL

SPRING AND TURN FREELY FOR NON-CONTROLLED

DELIVERY.

CONTRACTOR CONTRACTOR

C04P0 STANDING HEIGHT UNDER COUNTER BASE SINK CABINET

WITH SOLID HINGED DOORS. COORDINATE ACTUAL

CLEAR CABINET DIMENSION WITH THE ACTUAL OUTSIDE

DIMENSION OF SINK THAT IS SPECIFIED TO ENSURE THAT

THEY ARE COMPATIBLE.

CONTRACTOR CONTRACTOR

CB020 WALL HUNG CABINET WITH TWO ADJUSTABLE SHELVES,

SOLID HINGED DOORS, AND SLOPING TOP WHERE

INDICATED.

CONTRACTOR CONTRACTOR

CD040 WALL HUNG CABINET WITH TWO ADJUSTABLE SHELVES,

SOLID HINGED DOORS, AND SLOPING TOP WHERE

INDICATED.

CONTRACTOR CONTRACTOR

CT020 A SOLID, NONPOROUS COUNTERTOP WITH A SMOOTH

SEAMLESS APPEARANCE. AN ACRYLIC-BASED SOLID

SURFACE PRODUCT. STANDARD THICKNESS OF 1", AND A

4" BUTT BACKSPLASH/CURB.

CONTRACTOR CONTRACTOR

K4665 OVEN, MICROWAVE, CONSUMER. GOVERNMENT GOVERNMENT

R6200 UNDERCOUNTER UTILITY REFRIGERATOR

APPROXIMATELY 35" H X 24" W X 26" D

GOVERNMENT GOVERNMENT

ROOM FINISH SCHEDULE

ROOM NO. ROOM NAME FLOOR BASE

EAST

WALL

NORTH

WALL

SOUTH

WALL

WEST

WALL CEILING CLG. HT. REMARKS

1 STAIR EXIST EXIST EXIST EXIST EXIST EXIST ACT 8'-0"

2 STAIR EXIST EXIST EXIST EXIST EXIST EXIST ES/P 22'-4"

101 COMMON BOILER ROOM SC RB P P P P ES/P 31'-0"

102 COMMON SHOP AREA SC RB P P P P ACT 8'-0"

103 COMMON EMERGENCY GENERATOR ROOM SC RB P P P P ES/P 8'-10"

104 COMMON PUMP ROOM SC RB P P P P ACT 12'-6"

201 BOILER MANAGER'S OFFICE VCT RB P P P P ACT 8'-0"

202 BOILER OPERATORS OFFICE VCT RB P P P P ACT 8'-0"

202A UNISEX TOILET/SHOWER PT PT PT PT PT PT ACT 8'-0"

202B ENGINEERING STORAGE SC RB P P P P ES/P 8'-0"

203 PARTS STORAGE SC RB P P P P ES/P 8'-0"

203A ENGINEERING STORAGE SC RB P P P P ES/P 13'-0"

204 ENGINEERING FEED WATER AREA SC RB P P P P ES/P 9'-4 1/2"

205 UNISEX LOCKERS PT PT P P P P ACT 9'-4 1/2"

206 UNISEX TOILET / SHOWER PT PT PT PT PT PT ACT 9'-4 1/2"

207 UPPER MEZZANINE SC EXIST P P P P ES/P 11'-2"

SCALE:

0' 2" 4" 8" 1'

3" = 1' - 0"

1 1/2" = 1'-0"A601

5 PLAN DETAIL AT BASE PLATE 1

1 1/2" = 1'-0"A601

6 PLAN DETAIL AT BASE PLATE 2

jhirschhorn Text Box

HW-3B

HW-3B

HW-2D

HW-E6

HW-2G

HW-2D

jhirschhorn Text Box

AA