20-Attachment GG – Prevailing Wage Rate Instructions.pdf

Revised 7/24/2025

PREVAILING WAGE RATE INSTRUCTIONS

PAYROLL SUBMITTAL INFORMATION

1. One copy of a Certified Payroll of the General Contractor and Subcontractor are to be submitted using Harris

County DEEO’s Labor Compliance Software. The General Contractor is responsible for Sub-Contractor payroll submittals.

2. All Certified Payrolls are to be submitted weekly.

3. If there is a week that no work was performed, a certified payroll must be submitted showing “NO WORK

PERFORMED”.

4. The General Contractor and/or Sub-Contractor are to make available copies of cancelled checks and check stubs for comparisons if requested by the Contract Compliance Officer.

WAGE RATE COMPLIANCE

The Harris County Prevailing Wage Rate poster must be displayed in a location that all workers have access and remain in place until the project is complete.

Harris County reserves the right for the Contract Compliance Officer to visit the job site and to interview the General

Contractor and Sub-Contractor employees on any given date or time during the construction period without prior notification.

The Contract Compliance Officer will ascertain that the proper wage rates are being paid to the employees in accordance with the contract documents. The General Contractor shall not allow work requiring a license to be performed by a worker who does not have the proper license. The General Contractor shall require, and shall require its subcontractors to require, that workers carry their licenses upon their persons while performing work on the Project and that such persons produce their licenses to the Contract Compliance Officer upon request. After being requested to produce a license, a worker is not to be allowed to perform further work requiring a license until the required license is produced. Should work requiring a license be performed by an unlicensed person despite the prohibitions of this paragraph, that person must be paid the prevailing wage rate applicable for a licensed craftsman performing such work.

Harris County will not recognize a worker that holds a journeyman’s license in a trade as eligible for pay at an apprentice rate for work in that trade.

In the event of discrepancy between the services performed and the wages paid, it will be documented, and the General

Contractor will be so notified.

Harris County reserves the right to withhold any payment due the General Contractor until such discrepancy is resolved and the necessary adjustment is made.

Apprentices may be used in any of the crafts listed where noted, if they are currently certified in a program recognized by the Bureau of Apprenticeship and Training, U.S. Department of Labor, providing the proper ratio between journeyman and apprentice is observed. Apprentice certification certificates must be supplied with the first weekly payroll upon which the apprentice’s name appears. If they are not certified as an apprentice, they must be paid as a journeyman and used as an apprentice.

TEXAS GOVERNMENT CODE CHAPTER 2258

The Contractor shall forfeit as a penalty to the County on whose behalf this contract is made, Sixty Dollars, ($60.00) for each worker, employed for each calendar day, or portion thereof, such worker is paid less than the said stipulated rates for any work done under this contract, by him or by any sub-contractor under him.

The Contractor and each sub-contractor shall keep, or cause to be kept, an accurate record showing the names of all workers, also the actual per diem wages paid to each of such workers.

"General Decision Number: TX20250034 02/07/2025

State: Texas

Construction Type: Heavy

Counties: Brazoria, Fort Bend, Galveston, Harris, Matagorda, Montgomery, Waller and Wharton Counties in Texas.

FLOOD CONTROL PROJECTS ONLY, (Does not Include any Water & Sewer Line work; Sewage Collection and Disposal Lines; Sewers (Sanitary Storm, etc.), or Shoreline Maintenance Water Mains and Water Supply Lines).

Note: Contracts subject to the Davis-Bacon Act are generally required to pay at least the applicable minimum wage rate required under Executive Order 14026 or Executive Order 13658.

Please note that these Executive Orders apply to covered contracts entered into by the federal government that are subject to the Davis-Bacon Act itself, but do not apply to contracts subject only to the Davis-Bacon Related Acts, including those set forth at 29 CFR 5.1(a)(1).

|If the contract is entered |� Executive Order 14026 | |into on or after January 30, | generally applies to the | |2022, or the contract is | contract. | |renewed or extended (e.g., an |� The contractor must pay | |option is exercised) on or | all covered workers at | |after January 30, 2022: | least $17.75 per hour (or | | | the applicable wage rate | | | listed on this wage | | | determination, if it is | | | higher) for all hours | | | spent performing on the | | | contract in 2025. | |If the contract was awarded on|� Executive Order 13658 | |or between January 1, 2015 and| generally applies to the | |January 29, 2022, and the | contract. | |contract is not renewed or |� The contractor must pay all| |extended on or after January | covered workers at least | |30, 2022: | $13.30 per hour (or the | | | applicable wage rate listed| | | on this wage determination,| | | if it is higher) for all | | | hours performing on that | | | contract in 2025. |

The applicable Executive Order minimum wage rate will be adjusted annually. If this contract is covered by one of the Executive Orders and a classification considered necessary for performance of work on the contract does not appear on this wage determination, the contractor must still submit a conformance request.

Additional information on contractor requirements and worker protections under the Executive Orders is available at http://www.dol.gov/whd/govcontracts.

Modification Number Publication Date

9/15/25, 10:56 AM SAM.gov https://sam.gov/wage-determination/TX20250034/0 1/7

0 02/07/2025

SUTX1998-009 03/26/1998

The following rates were revised pursuant to 29 CFR 1.6(c)(1) on 02/07/2025.

Rates Fringes

ASPHALT DISTRIBUTOR..............$ 19.87

Asphalt Paving Machine...........$ 21.09

Asphalt Raker....................$ 17.38 **

Asphalt Shoveler.................$ 15.63 **

Batching Plant Weigher...........$ 23.31

Broom or Sweeper Operator........$ 16.81 **

Bulldozer........................$ 20.80

CARPENTER........................$ 21.72

Concrete Curbing Mach............$ 18.47

Concrete Finisher-Paving.........$ 20.71

Concrete Finisher-Structures.....$ 20.69

Concrete Finishing Machine.......$ 24.74

Concrete Joint Sealer............$ 22.03

Concrete Paving Float............$ 19.52

Concrete Paving Saw..............$ 21.01

Concrete Paving Spreader.........$ 19.56

Concrete Rubber..................$ 18.89

Crane, Clamshell, Backhoe, Derrick, Dragline, Shovel........$ 23.82

Crusher or Screening Plant Operator.........................$ 23.08

ELECTRICIAN......................$ 33.89

Flagger..........................$ 15.21 **

Form Builder (Structures)........$ 20.90

Form Liner - Paving & Curb.......$ 18.95

Form Setter (PAVING/CURB)........$ 18.59

Form Setter-Structures...........$ 18.99

Foundation Drill Operator, Crawler Mounted..................$ 26.42 https://sam.gov/wage-determination/TX20250034/0 2/7

Foundation Drill Operator, Truck Mounted....................$ 26.71

Front End Loader.................$ 19.50

Labor Common.....................$ 15.63 **

Laborer-Utility..................$ 17.90

Lineperson.......................$ 15.74 **

MANHOLE BUILDER (Brick)..........$ 17.82

MECHANIC (Undefined).............$ 23.88

Milling Machine Operator.........$ 21.89

Mixer............................$ 16.66 **

Motor Grader

FINE GRADE..................$ 23.31

Other.......................$ 22.39

Oiler............................$ 20.06

Painter-Structures...............$ 29.38

Pavement Marking Machine.........$ 15.63 **

Piledriver.......................$ 23.00

Pipe layer.......................$ 17.82

Reinforcing Steel Setter Paving...........................$ 26.23

Reinforcing Steel Setter Structures.......................$ 26.17

Roller, Pneumatic, Self Propelled........................$ 16.70 **

Roller, Steel Wheel Other Flatwheel or Tamping.............$ 15.97 **

Roller, Steel Wheel Plant Mix Pavements........................$ 19.41

Scraper..........................$ 18.24

Servicer.........................$ 19.96

SIGN ERECTOR.....................$ 21.11

Sign Installer...................$ 15.63 **

Slipform Machine Operator........$ 19.31

Spreader Box Operator............$ 19.05

Steelworker Structural...........$ 21.72

Tractor-Crawler Type.............$ 21.24

Tractor-Pneumatic................$ 18.87 https://sam.gov/wage-determination/TX20250034/0 3/7

Traveling Mixer..................$ 19.62

Trenching Machine, Heavy.........$ 28.46

Trenching Machine, Light.........$ 22.03

Truck Driver Lowboy Float........$ 23.69

Truck Driver Single Axle Heavy...$ 18.38

Truck Driver Single Axle, Light............................$ 17.10 **

Truck Driver Tandem Axle Semi-Trailer.....................$ 16.79 **

Wagon Drill, Boring Machine......$ 21.30

WELDER...........................$ 21.89

Work Zone Barricade..............$ 15.63 **

WELDERS - Receive rate prescribed for craft performing operation to which welding is incidental.

** Workers in this classification may be entitled to a higher minimum wage under Executive Order 14026 ($17.75) or 13658 ($13.30). Please see the Note at the top of the wage determination for more information. Please also note that the minimum wage requirements of Executive Order 14026 are not currently being enforced as to any contract or subcontract to which the states of Texas, Louisiana, or Mississippi, including their agencies, are a party.

Note: Executive Order (EO) 13706, Establishing Paid Sick Leave for Federal Contractors applies to all contracts subject to the Davis-Bacon Act for which the contract is awarded (and any solicitation was issued) on or after January 1, 2017. If this contract is covered by the EO, the contractor must provide employees with 1 hour of paid sick leave for every 30 hours they work, up to 56 hours of paid sick leave each year.

Employees must be permitted to use paid sick leave for their own illness, injury or other health-related needs, including preventive care; to assist a family member (or person who is like family to the employee) who is ill, injured, or has other health-related needs, including preventive care; or for reasons resulting from, or to assist a family member (or person who is like family to the employee) who is a victim of, domestic violence, sexual assault, or stalking. Additional information on contractor requirements and worker protections under the EO is available at https://www.dol.gov/agencies/whd/government-contracts.

Unlisted classifications needed for work not included within the scope of the classifications listed may be added after award only as provided in the labor standards contract clauses (29CFR 5.5 (a) (1) (iii)).

https://sam.gov/wage-determination/TX20250034/0 4/7

The body of each wage determination lists the classifications and wage rates that have been found to be prevailing for the type(s) of construction and geographic area covered by the wage determination. The classifications are listed in alphabetical order under rate identifiers indicating whether the particular rate is a union rate (current union negotiated rate), a survey rate, a weighted union average rate, a state adopted rate, or a supplemental classification rate.

Union Rate Identifiers

A four-letter identifier beginning with characters other than ""SU"", ""UAVG"", ?SA?, or ?SC? denotes that a union rate was prevailing for that classification in the survey. Example:

PLUM0198-005 07/01/2024. PLUM is an identifier of the union whose collectively bargained rate prevailed in the survey for this classification, which in this example would be Plumbers.

0198 indicates the local union number or district council number where applicable, i.e., Plumbers Local 0198. The next number, 005 in the example, is an internal number used in processing the wage determination. The date, 07/01/2024 in the example, is the effective date of the most current negotiated rate.

Union prevailing wage rates are updated to reflect all changes over time that are reported to WHD in the rates in the collective bargaining agreement (CBA) governing the classification.

Union Average Rate Identifiers

The UAVG identifier indicates that no single rate prevailed for those classifications, but that 100% of the data reported for the classifications reflected union rates. EXAMPLE:

UAVG-OH-0010 01/01/2024. UAVG indicates that the rate is a weighted union average rate. OH indicates the State of Ohio.

The next number, 0010 in the example, is an internal number used in producing the wage determination. The date, 01/01/2024 in the example, indicates the date the wage determination was updated to reflect the most current union average rate.

A UAVG rate will be updated once a year, usually in January, to reflect a weighted average of the current rates in the collective bargaining agreements on which the rate is based.

Survey Rate Identifiers

The ""SU"" identifier indicates that either a single non-union rate prevailed (as defined in 29 CFR 1.2) for this classification in the survey or that the rate was derived by computing a weighted average rate based on all the rates reported in the survey for that classification. As a weighted average rate includes all rates reported in the survey, it may include both union and non-union rates. Example: SUFL2022-007 6/27/2024. SU indicates the rate is a single non-union prevailing rate or a weighted average of survey data for that classification. FL indicates the State of Florida. 2022 is the year of the survey on which these classifications and rates are based. The next number, 007 in the example, is an internal number used in producing the wage determination. The date, 6/27/2024 in the example, indicates the survey completion date for the classifications and rates under that identifier.

?SU? wage rates typically remain in effect until a new survey is conducted. However, the Wage and Hour Division (WHD) has the https://sam.gov/wage-determination/TX20250034/0 5/7 discretion to update such rates under 29 CFR 1.6(c)(1).

State Adopted Rate Identifiers

The ""SA"" identifier indicates that the classifications and prevailing wage rates set by a state (or local) government were adopted under 29 C.F.R 1.3(g)-(h). Example: SAME2023-007 01/03/2024. SA reflects that the rates are state adopted. ME refers to the State of Maine. 2023 is the year during which the state completed the survey on which the listed classifications and rates are based. The next number, 007 in the example, is an internal number used in producing the wage determination.

The date, 01/03/2024 in the example, reflects the date on which the classifications and rates under the ?SA? identifier took effect under state law in the state from which the rates were adopted.

WAGE DETERMINATION APPEALS PROCESS

1) Has there been an initial decision in the matter? This can be:

a) a survey underlying a wage determination

b) an existing published wage determination

c) an initial WHD letter setting forth a position on a wage determination matter

d) an initial conformance (additional classification and rate) determination

On survey related matters, initial contact, including requests for summaries of surveys, should be directed to the WHD Branch of Wage Surveys. Requests can be submitted via email to davisbaconinfo@dol.gov or by mail to:

Branch of Wage Surveys Wage and Hour Division U.S. Department of Labor 200 Constitution Avenue, N.W.

Washington, DC 20210

Regarding any other wage determination matter such as conformance decisions, requests for initial decisions should be directed to the WHD Branch of Construction Wage Determinations.

Requests can be submitted via email to BCWD-Office@dol.gov or by mail to:

Branch of Construction Wage Determinations Wage and Hour Division U.S. Department of Labor 200 Constitution Avenue, N.W.

Washington, DC 20210

2) If an initial decision has been issued, then any interested party (those affected by the action) that disagrees with the decision can request review and reconsideration from the Wage and Hour Administrator (See 29 CFR Part 1.8 and 29 CFR Part 7).

Requests for review and reconsideration can be submitted via email to dba.reconsideration@dol.gov or by mail to:

Wage and Hour Administrator U.S. Department of Labor 200 Constitution Avenue, N.W.

Washington, DC 20210 https://sam.gov/wage-determination/TX20250034/0 6/7

The request should be accompanied by a full statement of the interested party's position and any information (wage payment data, project description, area practice material, etc.) that the requestor considers relevant to the issue.

3) If the decision of the Administrator is not favorable, an interested party may appeal directly to the Administrative Review Board (formerly the Wage Appeals Board). Write to:

Administrative Review Board U.S. Department of Labor 200 Constitution Avenue, N.W.

Washington, DC 20210.

END OF GENERAL DECISION"

https://sam.gov/wage-determination/TX20250034/0 7/7