B08_Solit_SCBL_152851_Attach_03_Product_Files.pdf

SCOTTS BLUFF NATIONAL MONUMENT

NEBRASKA

Visitor Center Rehabilitation & Expansion

PMIS NO. 152851

PRODUCT FILE

NATIONAL PARK SERVICE

DENVER SERVICE CENTER

100% FINAL CONSTRUCTION DOCUMENTS

June 23, 2017

VC REHABILITATION & EXPANSION

SCOTTS BLUFF NATIONAL MONUMENT – PMIS 152851

PRODUCT FILES

DIVISION 3: CONCRETE……………………………………………………………………………………………………….. 3

Vapor Barrier

DIVISION 4: MASONRY……………………………………………………………………………………………………….. 5

Brick

DIVISION 5: WOOD, PLASTIC AND COMPOSITES………………………………………………………………… 14

Cabinet Hardware

Laminate Shelving

DIVISION 7: THERMAL AND MOISTURE PROTECTION…………………………………………………………. 24

Sheet Waterproofing

Fluid‐Applied Waterproofing

Thermal Insulation

Wood Shingles

DIVISION 8: OPENINGS……………………………………………………………………………………………………….. 66

Hollow Metal Doors

Clad Wood Doors

Stile and Rail Wood Doors

Clad Wood Windows

Door Hardware

DIVISION 9: FINISHES……………………………………………………………………………………………………….. 96

Gypsum Board Assemblies

Plaster

Stucco

Tile

Direct Applied Acoustic Ceiling

Resilient Flooring

Carpeting

Wall Coverings

DIVISION 10: SPECIALTIES……………………………………………………………………………………………………….. 143

Plastic Toilet Compartments

Restroom Accessories

DIVISION 12: FURNISHINGS……………………………………………………………………………………………………….. 163

Window Shades

DIVISION 22: PLUMBING……………………………………………………………………………………………………….. 167

Valves

Drinking Fountain

Water Heater

Lavatory Faucets

Express Deck Lavatory System

Wall Hung Lavatory

Mop Service Basin

Pump

Trench Drain

Meter

Toilet Systems

DIVISION 23: HEATING, VENTILATION AND AIR CONDITIONING…………………………………………… 208

Air Conditioners

Heaters

Direct Drive Cabinet Fan

Unit Heater

Louvered Gravity Relief Ventilator

ERCH‐20‐15H

Grilles

MCU

VRF

DIVISION 26: ELECTRICAL……………………………………………………………………………………………………….. 407

Lighting

Controls

Electrical Gear

Generator

DIVISION 3: CONCRETE

1. Product Name Stego Wrap Vapor Barrier

2. Manufacturer Stego Industries, LLC 216 Avenida Fabricante, Suite 101 San Clemente, CA 92672 Sales, Technical Assistance Ph: (877) 464-7834 Fx: (949) 257-4113 www.stegoindustries.com

3. Product Description USES: Stego Wrap Vapor Barrier is used as a below-slab vapor barrier.

COMPOSITION: Stego Wrap Vapor Barrier is a multi-layer plastic extrusion manufactured with only high grade prime, virgin, polyolefin resins.

ENVIRONMENTAL FACTORS:

Stego Wrap Vapor Barrier can be used in systems for the control of soil gases (radon, methane), soil poisons (oil by-products) and sulfates.

Vapor Retarders 07 26 00, 03 30 00

5. Installation UNDER SLAB: Unroll Stego Wrap Vapor Barrier over an aggregate, sand or tamped earth base. Overlap all seams a minimum of six inches and tape using Stego Tape or Crete Claw® Tape. All penetrations must be sealed using a combination of Stego Wrap and Stego accessories.

For additional information, please refer to Stego's complete installation instructions.

6. Availability & Cost Stego Wrap Vapor Barrier is available nationally via building supply dis-tributors. For current cost information, contact your local Stego Wrap dis-tributor or Stego Industries’ sales department.

7. Warranty Stego Industries, LLC believes to the best of its knowledge, that specifications and recommendations herein are accurate and reliable. However, since site conditions are not within its control, Stego Industries does not guarantee results from the use of the information provided and disclaims all liability from any loss or damage. NO WARRANTY, EXPRESS, IMPLIED OR STATUTORY, IS

GIVEN AS TO THE MERCHANTABILITY,

FITNESS FOR A PARTICULAR PURPOSE,

OR OTHERWISE WITH RESPECT TO THE

PRODUCTS REFERRED TO. Please see www.stegoindustries.com/legal.

8. Maintenance None required.

9. Technical Services Technical advice, custom CAD drawings, and additional information can be obtained by contacting Stego Industries’ technical assistance department or via the website.

10. Filing Systems

• Stego Industries’ website

• Buildsite

STEGO INDUSTRIES, LLC

Stego® Wrap Vapor Barrier

TABLE 1: PHYSICAL PROPERTIES OF STEGO WRAP VAPOR BARRIER

PROPERTY TEST RESULTS

Under Slab Vapor Retarders ASTM E1745 Class A, B & C – Standard Specification for Water Vapor Retarders Used in Contact with Soil or Granular Fill under Concrete Slabs Exceeds Class A, B & C

Water Vapor Permeance ASTM F1249 – Test Method for Water Vapor Transmission Rate Through Plastic Film and 0.0086 perms Sheeting Using a Modulated Infrared Sensor *0.0036 WVTR

Puncture Resistance ASTM D1709 – Test Methods for Impact Resistance of Plastic Film by Free-Falling Dart Method 2266 grams

Tensile Strength ASTM D882 – Test Method for Tensile Properties of Thin Plastic Sheeting 70.6 lbf/in.

Permeance After Conditioning ASTM E154 Section 8, F1249 – Permeance after wetting, drying, and soaking 0.0098 perms (ASTM E1745 ASTM E154 Section 11, F1249 – Permeance after heat conditioning 0.0091 perms Sections 7.1.2 - 7.1.5) ASTM E154 Section 12, F1249 – Permeance after low temperature conditioning 0.0097 perms ASTM E154 Section 13, F1249 – Permeance after soil organism exposure 0.0095 perms

Methane Transmission Rate ASTM D1434 – Standard Test Method for Determining Gas Permeability Characteristics **192.8 GTR of Plastic Film and Sheeting mL(STP)/m2*day

Radon Diffusion Coefficient K124/02/95 8.8 x 10-12m2/second

Thickness 15 mils

Roll Dimensions 14 ft. wide x 140 ft. long or 1,960 ft2

Roll Weight 140 lbs.

Note: perm unit = grains/(ft2 *hr* in.Hg) * WVTR = Water Vapor Transmission Rate ** GTR = Gas Transmission Rate

4. Technical Data

Stego, the stegosaurus design logo[s], Crete Claw, StegoTack, StegoCrawl, Beast, and the Beast design logo are all deemed to be registered and/or protectable trademarks or service marks of Stego Industries, LLC. © 2016 Stego Industries, LLC. All Rights Reserved. Please see www.stegoindustries.com/legal. 5/2016

DIVISION 4: MASONRY

* Selecting a product from a General Shale plant nearest your construction site can significantly reduce your cost of delivery.

BASILICA

Manufactured in our Denver, CO Plant*

Clay brick is the superior building material for residential and commercial projects. Stronger and more sustainable than other building materials, its beauty and value is unmatched. Choose from classic red bricks to warm earth tones and unique pastels.

SIZES

Name Dimensions Sku Modular Size (Denver)3‐5/8"W x 2‐1/4"H x 7‐5/8"L6060008036

The Standard of Comparison since 1885 www.beldenbrick.com An ISO 9001 Compliant Quality Management System

An ISO 14001 Compliant Quality Management System

Face Brick

Thin Brick Special ShapesClay Pavers

Stivers School for the Arts Dayton OH Jeff Wray Architects Beacon Gray – Double Monarch Canyon Full Range Velour – Monarch and Modular

Concept Catalog Featuring : Product Snapshots – Offerings and Selections

Face Brick

Owner - Pedcor Companies / Carmel, IN Project - Indiana Design Center

Extruded Brick

ALASKA WHITE VELOUR 481-483 VELOUR POTOMAC CLEAR LIGHTHOUSE GRAY VELOUR

661 VELOUR 671 SMOOTH 691-693 8520

920-926 BURBANK FULL RANGE DUTCH GRAY MATTE SEA GRAY VELOUR

COLORS Belden currently makes face brick in over 300 colors that range from frosted whites to pinks to deep reds... burgundies... chocolates...

buffs, grays and charcoal tones. Belden Brick color choices offer significant design latitude that is enhanced by intermixed brick and by firing techniques that produce further tonal variety within a given color range.

2 (330) 456-0031 / beldenbrick.com

We make brick in a broad range of colors and textures. Space does not permit showing all of them within this catalog. The following pages do offer a sampling of that range. To inspect the many other Belden Brick choices, please visit us online or call us for your nearest Belden Brick distributor. Because of printing limitations and lighting variances, the colors shown below may vary from the actual brick. We recommend requesting sample brick before making selections.

MARIGOLD BLEND NEVADA BLEND PAGO VELOUR WHEATFIELD VELOUR

SANDY ROSE 503-505 BISMARK BLEND BUCKINGHAM BLEND

TEXTURES & SIZES Belden Brick is offered in textures that range from the sand mold finish of colonial times to rugged randomly textured styles...

vertically grooved styles or silky finishes. Each texture can make its own distinctive contribution to the visual impact you seek. Belden Brick is regularly manufactured in sixteen different sizes. Representative dimensions and related information are provided on pages 10 and 11.

514 CONCORD BLEND

MAYO BLEND FULL RANGE GRAYSTONE SMOOTH SILVER SATIN QUAKER BLEND VELOUR

TUMBLEWEED 461-463 SMOOTH

3(330) 456-0031 / beldenbrick.com

GARDEN BLEND TULIP BLEND ROYALTY RED RUM RAISIN

4 (330) 456-0031 / beldenbrick.com

EBONY BLACK ASHBERRY VELOUR BLACK DIAMOND VELOURNAPIER BLEND

The Indiana Design Center - Commodore Red Velour, Claret Velour & 470-479 Light Range Ironspots.

TUDOR BLEND 470-479 LIGHT RANGE 470-479 MEDIUM RANGE 470-479 DARK RANGE

8621 BEAVER BLEND DART-TEX BRANDYWINE VELOUR MIDLAND BLEND

BLENDING Belden takes the extra manufacturing step of factory-blending its brick. That way we can control and randomize minor color variations and assure color consistency in the finished structure. Our blending procedure means brick can be laid up just as it comes off the package without concern for concentrated color variances. Please be aware that these colors only reflect a portion of our product line. To view every color in our catalog, you can visit us online at beldenbrick.com.

5(330) 456-0031 / beldenbrick.com

POLAR WHITE CLEAR ALAMO BLEND MANCHESTER BLEND

ST. ANNE BLEND ST. ANNE CLEAR KINGSPORT

ROSEWOOD CLEAR ROSEWOOD BLEND GARNET BLEND

BELCREST 310 BELCREST 360 BELCREST 500

BELCREST 560 BELCREST 650 BELCREST 760

Molded Brick

15(330) 456-0031 / beldenbrick.com

GU

ID

E

TO

B

RI

CK

D

IM

EN

SI

ON

S

DA

TA

W

AL

L

CO

ST

P

ER

S

QU

AR

E

FO

OT

E

ST

IM

AT

IN

G

TA

BL

E

BR

IC

K

UN

IT

AP

PR

OX

IM

AT

E W

EI

GH

T

SI

ZE

IN

CH

ES

(B

D x

H x

L)

FA

CE

M

.B .E

UN

IT

S

PE

R

SQ

. F

T.

W

AL

L

(in c.

/8

Jo in t)

SI

ZE

(M M

ES

TI

M

AT

ED

C

OS

T

OF

B

RI

CK

UN

IT

S

PE

R

SQ

UA

RE

F

OO

T

ES

TI

M

AT

ED

C

OS

T

OF

L

AB

OR

O

TH

ER

M

AT

ER

IA

L

PE

R

SQ

UA

RE

F

OO

T

TO

TA

L

ES

TI

M

AT

ED

C

OS

T

PE

R

SQ

UA

RE

F

OO

T

M

OD

UL

AR

4.

3#

3- 5/

8” x

-1

/4 x 7-

5/ 8”

1.

6.

x x

ST

AN

DA

RD

4.

5#

3- 5/

8” x

-1

/4 x 8”

1.

6.

x x

JU

M

BO

M

OD

UL

AR

5.

1# 3-

5/ 8” x

-3 /4 x

7- 5/

8” 1.

5.

x x

QU

EE

N 5.

6# 3-

1/ 8” x

-3 /4 x

9- 5/

8” 1.

4.

x x

NO

RM

AN

6.

3# 3-

5/ 8” x

-1 /4 x

-5

/8

1.

4.

x x

SL

IM

J

UM

BO

NO

RM

AN

7.

2#

3- 1/

8” x

-3

/4 x

-5 /8

1.

3.

x x

JU

M

BO

N

OR

M

AN

7.

8# 3-

5/ 8” x

-3 /4 x

-5

/8

1.

3.

x x

EC

ON

OM

O

M

OD

UL

AR

6.

6#

3- 5/

8” x

-5

/8 x 7-

5/ 8”

1.

4.

x x

UT

IL

IT

Y

.5

3-

5/ 8” x

-5 /8 x

-5

/8

2.

3.

x x

QU

AD

.5

3-

5/ 8” x

-5 /8 x

7- 5/

8” 3.

2.

x x

TH

RU

W

AL

L 5-

5/ 8”

.5

5-

5/ 8” x

-5 /8 x

-5

/8

2.

3.

x x

TH

RU

W

AL

L 7-

5/ 8”

.0

7-

5/ 8” x

-5 /8 x

-5

/8

2.

3.

x x

M

ON

AR

CH

.5

3-

5/ 8” x

-5 /8 x

-5

/8

3.

2.

x x

M

OD

UL

AR

(M

OL

DE

D )

4.

9#

3- 5/

8” x

-1

/4 x 7-

5/ 8”

6.

x x

JU

M

BO

(M

OL

DE

D) 5.

9# 3-

5/ 8” x

-5 /8 x

8” 1.

5.

x x

AM

BA

SS

AD

OR

8.

4# 3-

5/ 8” x

-1 /4 x

-5

/8

2.

3.

x x

DO

UB

LE

U

TI

LI

TY

.0

3- 5/

8” x

-5

/8 x

-5 /8

5.

1.

x x

DO

UB

LE

M

ON

AR

CH

.0

3- 5/

8” x

-5

/8 x

-5 /8

6.

1.

x x

RO

M

AN

4.

7# 3-

5/ 8” x

-5 /8 x

-5

/8

1.

6.

x x

700 West Tuscarawas • Canton, Ohio 44702 Phone: 330-456-0031 • Fax: 330-456-2694 • www.beldenbrick.com

TECHNICAL SUPPORT AND CONSULTATION

Our staff is available at all times to answer technical questions or consult with you on any aspect of your interest in brick. Call any one of our authorized distributors or call Jim Tann at our main office: (330) 456-0031.

GUIDE TO SPECIFYING DIVISION 4 SECTION 04210

PART II PRODUCTS

2.01 BRICK

A. Facing Brick: All brick specified and shown on drawing shall be (product name)

__________________________ as manufactured by The Belden Brick Company, Canton, Ohio.

1. ASTM C-216 _______________________, Grade SW, Type _____________

2. Dimensions ___________ X ____________ X ____________

3. Provide brick similar in texture, color and all physical properties to those available for inspection at the Architect/Engineer’s office and/or as supplied on the approved sample panel.

4. Other Requirements (Optional)

a. Shapes: All special shapes are to be used per architectural detail(s) #____________ as supplied to The Belden Brick Company.

b.1 Minimum compressive strength ___________psi (if greater than 3,000 psi) c.2 Maximum IRA__________ g/min/30 sq.in.

B. Mortar: Conventional mortar shall conform with ASTM C-270 under the guidelines provided in BIA Technical Notes, Series 8.

PART III EXECUTION

A. Bonding: Lay masonry in __________________bond pattern as indicated.

Reference BIA Technical Note #30 for further recommendations.

B. Tooling: Tooling shall conform to the guidelines provided in BIA Technical Notes #7B.

C. Cleaning: Cleaning shall be as per guidelines in BIA Technical Note #20.

All cleaning practices and product use shall also be in accordance with cleaning agent manufacturers printed instructions.

NOTES TO SPECIFIER:

ASTM DESIGNATION C-216 (with the last number being the year of the last update). All A grade Belden Brick complies with ASTM C-216, grade SW (severe weathering).

A Type FBS – Brick for general use in masonry.

B Type FBX – Brick for general use in masonry where a higher degree of precision and lower permissible variation in size than permitted for type FBS is required.

C Type FBA – Brick for general use in masonry selected to produce characteristic architectural effects resulting from non-uniformity in size and texture of the individual units.

When the type is not specified the requirements for the type FBS shall govern.

The above is per ASTM Designation C-216 Standard Specification for Facing Brick (Solid Masonry Units Made From Clay or Shale).

QUALITY BRICK FOR MORE THAN 125 YEARS

A SAMPLING OF BELDEN BRICK AT WORK

UNIVERSITY / SCHOOL

Alice H. Cook House Cornell University Ithaca, NY Kieran Timberlake Associates, LLP

David Letterman Communication & Media Bldg.

Muncie, IN MSKTD & Associates, Inc.

Earth Sciences Building & Museum of Natural History Amherst, MA Payette

Grand Valley State University DeVos Center Grand Rapids, MI Design Plus Inc.

Stayer Center for Executive Education at the University of Notre Dame South Bend, IN The S/L/A/M Collaborative

Leazar Hall NC State University Raleigh, NC Cannon Architects

Taconic Hills School Hillsdale, NY Rhinebeck Architectural & Planning

The Ohio State University Fisher School of Business Columbus, OH Karlsberger Co.

University of Cincinnati

Mary Emory Hall Cincinnati, OH I. M. Pei

University of Pittsburgh Convocation Center Oakland, PA Apostolou & Associates

CHURCHES

First Friends Church North Canton, OH Harris-Day Architects Inc

Holy Angels Church Chagrin Falls, OH Zarzycki – Malik Architects

SHOPS / COMMERICAL

Crocker Park Westlake, OH Bialosky + Partners Architects

Mayfaire Town Center Wilmington, NC Cooper Carry, Inc.

Whole Foods Market Washington, DC Mushinsky Voelzke Associates16 (330) 456-0031 / beldenbrick.com

HEALTHCARE

Clarion North Medical Center Carmel, IN HKS, Inc.

Good Samaritan North Hospital Englewood, OH Earl Swensson Associates

The Eye Center Columbus, OH Gil Sass–AMB Development Group

Womack Replacement Hospital Fort Bragg –Fayetteville, N.C.

The Smith Group, Inc.

Midwest Express Center Milwaukee, WI Thompson, Ventulett, Stainbach & Associates

STADIUMS / ARENAS

Boston College Sports Complex Chestnut Hill, MA Sasaki Associates, Inc.

Busch Stadium St. Louis, MO HOK Architects

Miller Park Milwaukee, WI HKS, Inc. / NBBJ / Eppstein Uhen Architects

American Airlines Center Dallas, TX David M. Schwarz Architectural Services

OFFICE / CORPORATION

AT&T Offices Monmouth County, NJ

CUH2A

Central Mutual Insurance Co.

Van Wert, OH Flad & Associates

Harry London’s Candies Canton, OH Lawrence, Dykes, Goodenberger, Vandegrift & Clancy

The Millennium Building Canton, OH Wilson Architectural Group

HIGH RISE

River House New York, NY Polshek Partnership Ismael Leyva Architects

Seaport Hotel World Trade Center Boston, MA The Stubbins Associates, Inc.

DIVISION 5: WOOD, PLASTIC AND COMPOSITES

w

Dimensions in mm unless otherwise noted. 88

STUDIO COLLECTION

Item No. Material Finish A B

1 106.61.043 Zinc oil-rubbed bronze 148 128

2 106.61.044 Zinc oil-rubbed bronze 180 160

3 106.61.123 Zinc oil-rubbed bronze 144 128

4 106.61.124 Zinc oil-rubbed bronze 176 160

5 106.61.223 Zinc polished chrome 144 128

6 106.61.224 Zinc polished chrome 176 160

1-2

M4

A

B

3-6

A

B

16 M4

NEW

Item No.

Quantity Min. 1

Line Level PO

106.61.123 Handle, Studio, H1565, zinc, oil-rubbed bronze, 105ZN27, M4, center to center 128mm

Finish

- Oil rubbed bronze, used look Polished chrome

Length

144 mm 176 mm

Hole spacing

128 mm 160 mm Product details

Depth 32 mm

Height 32 mm

Thread M4

Material Zinc

Finish Code 105ZN27

Related products and accessories

M4 threaded screws

Page 1 of 1Handle, Zinc - in the Häfele America Shop

3/22/2017https://www.hafele.com/us/en/product/handle-zinc/10661123/;pgid=TCFg67K4i8RSRpI88...

www.wilsonart.com http://www.wilsonart.com/laminate/design-library http://static.wilsonart.com.cdnga.net/sites/default/files/docs/resources/technical-information-warranty-wilsonart-laminate.pdf https://issuu.com/wilsonart/docs/wilsonart___care_and_maintenance_br?e=1726292/14175198

DIVISION 7: THERMAL AND MOISTURE PROTECTION

800.527.7092 | www.carlisleccw.com

WATERPROOFING

CCW MiraDRI® 860/861

Self-Adhering Sheet-Applied Waterproofing Membrane

SCIENCE. SERVICE. SOLUTIONS.

CCW MiraDRI: A Foolproof Waterproofing System

CCW MiraDRI self-adhering membranes are composite materials consisting of a specially formulated rubberized asphalt laminated to a high-impact-resistant HDPE fi lm. The CCW MiraDRI waterproofi ng system is designed to provide waterproofi ng protection for below-grade foundation walls, slabs, parking decks, plaza decks, tunnels and many applications. The CCW

MiraDRI waterproofi ng system consists of the self-adhering membrane, an environmentally friendly water-based primer for surface preparation, a liquid membrane for detailing and mastic to seal termination points.

The installed CCW MiraDRI waterproofi ng membrane is protected by

CCW MiraDRAIN drainage composites or a CCW Protection Course. CCW

MiraDRAIN drainage composites protect waterproofi ng systems and keep the water away from the building structure. CCW MiraDRAIN provides a cost-effective solution as compared to traditional protection boards and aggregate drainage systems.

Carlisle Coatings & Waterproofi ng, Inc. (CCW) provides a broad range of solutions to meet specifi c waterproofi ng needs. CCW offers technical services, research & development and manufacturing capabilities from its headquarters in Wylie, Texas and two additional manufacturing facilities in Terrell, TX and Carlisle, PA. The CCW network is further supported by over 50 manufacturer’s sales representatives directed by regional sales offi ces throughout the country. CCW offers a complete line of waterproofi ng and moisture protection products for the architectural, general construction, industrial and maintenance industries. Carlisle Coatings & Waterproofi ng, Inc., is part of the Carlisle Construction Materials Division of Carlisle Companies, Inc., which is a publicly traded company on the NYSE.

Protection from the damaging effects of water can be achieved quickly and easily with CCW MiraDRI 860/861.

Focusing on below-grade foundation walls, this peel-and-stick waterproofi ng membrane is easy to handle, simple to apply and provides long-lasting protection. CCW MiraDRI

860/861 works best when suited with the appropriate

CCW MiraDRAIN® Drainage System, which protects the membrane, provides a channel for water migration and eliminates hydrostatic pressure. With all the benefi ts of factory-controlled properties and the waterproofi ng characteristics of asphalt, CCW MiraDRI 860/861 is the easy choice for contractors and applicators alike.

WATERPROOFING

CCW MiraDRI 860/861

Self-Adhering Sheet-Applied Waterproofing Membrane

CCW-704 Mastic

CCW MiraDRAIN 6200 CCW MiraDRI 860/861 CCW Contact Adhesive

CCW-201,

CCW LM-800XL,

or CCW 703V Liquiseal

Installation

CCW MiraDRI 860 Membrane is used for applications where surface temperatures are 40°F (4.4°C) and above. CCW MiraDRI 861 is specially formulated for applications with cooler surface temperatures down to 25°F

– 65°F (-3.9°C – 18°C). CCW MiraDRI 860/861 membranes should not be applied in temperatures below 25°F (-3.9°C).

Substrate Preparation: CCW MiraDRI 860/861 can be applied to concrete, metal, wood, insulated wall systems or masonry surfaces. All substrates must be clean, dry and free of surface irregularities.

Concrete Substrates: Structural concrete must be cured a minimum of seven days and lightweight structural concrete must cure a minimum of 14 days before the application of CCW MiraDRI 860/861. Repair surfaces that are not structurally sound, have voids, protrusions, rough spalled areas, loose aggregate or exposed course aggregate. Void areas should be fi lled with latex Portland cement, concrete or epoxy concrete and troweled smooth to match the existing surface. Protrusions and other rough areas should be ground down and patched as above. CCW LM-800XL, CCW-201, or CCW

703V Liquiseal may be used to fi ll small voids, honeycombs or bug holes.

Masonry Substrate: Rough masonry may require the surface to be parged with a plaster coat of cementitious material to form a well-adhered, smooth and uniform fi nish. Allow the parge coat to dry before priming and installing the CCW MiraDRI 860/861 waterproofi ng membrane.

Priming: Apply the appropriate CCW Contact Adhesive at the specifi ed coverage rate. Apply CCW Contact Adhesive with a lambswool roller, brush or spray apparatus. Allow Contact Adhesive to dry for a minimum of 30 minutes.

The CCW Contact Adhesive will dry to a tacky fi nish. Areas applied but not covered with CCW MiraDRI 860/861 within 24 hours should be re-applied.

Surface Preparation for Gypsum-Sheathing with Glass-Mat Facers:

When installing CCW sheet membranes and sheet fl ashings over gyp-sheathing with glass-mat facers, coverage rates for contact adhesives and primers will depend on the porosity and texture of the sheathing and will vary substantially by gypsum-sheathing brand and manufacturer. To achieve consistent contact adhesive and/or primer coverage with adequate tack, it may be necessary to decrease the coverage rate (i.e. increase the amount applied) of the contact adhesive and/or primer and/or the application of multiple coats. CCW Contact adhesives and primers shall be allowed to dry completely (lower temperatures will extend drying time) before additional coats are applied or membranes installed. Caution should be taken as contact adhesives and/or primers applied to gyp-sheathings with glass-mat facers will take longer to dry than other substrates. Multiple adhesion tests should be performed randomly to verify proper application of primer and ensure a successful application.

Membrane Application: Start membrane application by removing the release paper. Begin applying the membrane, beginning at the low point and working toward the high point. Side laps should be 2½" (6.3

cm) minimum and end laps should be 5" (12.7 cm) minimum. CCW recommends that the membrane be rolled in place immediately after its placement to ensure full adhesion to the primed substrate. A minimum

1" fi llet should be applied at juncture of footing and foundation wall. Double coverage should be used on all inside and outside corners using a 9" (22.9

cm) strip of CCW MiraDRI 860/861. All joints, drains, penetrations and protrusions should also receive double coverage. All terminations of the membrane should receive a troweled bead of CCW-704 Mastic, CCW LM-

800XL, CCW-201 or CCW 703V Liquiseal.

Membrane Protection: CCW MiraDRAIN Drainage Composites, CCW Protection Boards or CCW Protection Fabric should be applied at the end of each day’s work to avoid damage caused by other trades, construction materials or backfi ll. For more information on installation guidelines, refer to the Manufacturer’s Guide Specifi cation or contact your local CCW representative.

Features & Benefits

• Fully Adhered Membrane: Eliminates water migration which can otherwise cause leakage through cracks

• Factory-controlled thickness: eliminates thin spots which could be easily penetrated, allowing leakage

• Preformed sheet: eliminates pinholing

• Flexibility over cracks: elastomeric properties accommodate normal expansion and contraction of the substrate

• Resists hydrostatic pressure

• Mechanically strong

• Easy to apply

• Cost-competitive: the highest performance system with the best lifecycle cost

02.10.17 © 2017 Carlisle.

REPRINT CODE: 601402 - “MiraDRI 860-861 Brochure”

Carlisle, , MiraDRI, and MiraDRAIN are trademarks of Carlisle.

Limited Warranty

Carlisle Coatings & Waterproofi ng, Incorporated (Carlisle) warrants this product to be free of defects in workmanship and materials only at the time of shipment from our factory. If any Carlisle materials prove to contain manufacturing defects that substantially affect their performance, Carlisle will, at its option, replace the materials or refund its purchase price.

This limited warranty is the only warranty extended by Carlisle with respect to its materials. There are no other warranties including the implied warranties of merchantability and fi tness for a particular purpose.

Carlisle specifi cally disclaims liability for any incidental, consequential or other damages including, but not limited to, loss of profi ts or damages to a structure or its contents arising under any theory of law whatsoever.

The dollar value of Carlisle’s liability and buyer’s remedy under this limited warranty shall not exceed the purchase price of the Carlisle material in question.

Carlisle Coatings & Waterproofi ng

900 Hensley Lane | Wylie, TX 75098 | 800.527.7092 | www.carlisleccw.com

Property Test Method Typical Value

Color — Dark Gray

Tensile (Membrane) ASTM D412 325 psi

Tensile (Film) ASTM D882 5,000 psi

Elongation ASTM D412 350%

Permeance ASTM E96 0.05 perms

Low Temp. Flexibility ASTM D1970 Unaffected, @ -45°F Cracking Cycle*

(100 Cycles) ASTM C836 Unaffected, @ -25°F

Peel Strength ASTM D903 10 lb/in

Lap Adhesion ASTM D1876 19.0 lb/in

Puncture Resistance ASTM E154 60 lb min

Soil Burial GSA-PBS 07121 16 wks, no effect

Water Absorption ASTM D570 0.1% by wt

Hydrostatic Head ASTM D5385 230 ft

*180° bend over a 1" (25 mm) mandrel at -45°F (-43°C)

Technical Data Applicable Standards

• GSA; PBS PCD 07121

• USN; NAVFAC TS-07111

• VA; H-08-1

• Federal Construction Guide Specs; FCGS-07111

• Corps of Engineers; CEGS-07111-3-82

• UL 790, Class A

• LA Research Report Number 25094L

TREMproof® 201/60

Fluid-Applied, Elastomeric Waterproofing www.tremcosealants.com Page 1 of 2

Product Description

TREMproof® 201/60 is a high-solids, VOC compliant, modified polyurethane waterproofing membrane. It is a one-part moisture-curing elastomer available in three viscosities: Self-Leveling (SL), Roller (R) and Trowel. (Trowel grade intended for detailing work only).

Basic Uses

TREMproof 201/60 is designed for use on backfilled walls, split slabs that slopes to drain, primarily on concrete, masonry and plywood.

Features and Benefits

TREMproof 201/60 is an economical choice for when construction schedules are not compressed.

Availability

Immediately available from your local Tremco Sales Representative or Distributor. For Distributor locations, visit www.tremcosealants.com.

Coverage Rates

Approximately 25 ft²/gal (0.61 M2/L) at 60 wet mils

Packaging

5-gal (19-L) pails, 36 pails/pallet

55-gal (208-L) drums, 4 drums/pallet

Limitations

Not for use in submerged or gas vapor conditions.

Do not apply to damp or contaminated surfaces.

Not to be used as an exposed or wearing surface.

Not approved for direct contact with asphalt-based products.

Use with adequate ventilation.

Contact your local Tremco Sales Representative or Tremco Technical Services for compatibility information and job-specific recommendations on tie-in and termination details.

Warranty

Tremco warrants its Products to be free of defects in materials but makes no warranty as to appearance or color. Since methods of application and on-site conditions are beyond our control and can affect performance, Tremco makes no other warranty, expressed or implied, including warranties of MERCHANTABILITY and FITNESS FOR A PARTICULAR PURPOSE with respect to Tremco Products. Tremco’s sole obligation shall be, at its option, to replace or to refund the purchase price of the quantity of Tremco Products proven to be defective, and Tremco shall not be liable for any loss or damage.

Please refer to our website at www.tremcosealants.com for the most up-to-date Product Data Sheets.

NOTE: All Tremco Safety Data Sheets (SDS) are in alignment with the Globally Harmonized System of Classification and Labelling of

Chemicals (GHS) requirements.

http://www.tremcosealants.com/

TREMproof® 201/60 Fluid-Applied, Elastomeric Waterproofing

0916/TP201-60DS-BG

Tremco Commercial Sealants & Waterproofing

3735 Green Rd Beachwood OH 44122

216.292.5000 / 800.321.7906

1451 Jacobson Ave Ashland OH 44805

419.289.2050 / 800.321.6357

220 Wicksteed Ave Toronto ON M4H1G7

416.421.3300 / 800.363.3213

1445 Rue de Coulomb Boucherville QC J4B 7L8 514.521.9555 www.tremcosealants.com Page 2 of 2

*Varies Depending on grade of material used.

**Modified ASTM C1305

TYPICAL PHYSICAL PROPERTIES

PROPERTY DESCRIPTION

Type Modified Polyurethane Waterproofing

Color Black

Solids No less than 85%*

Application Roller/Trowel/Squeegee

Thickness 60 mils

PROPERTY TEST METHOD TYPICAL VALUES

Adhesion-in-Peel after Water Immersion (Unprimed)

ASTM C836; ASTM C 794 8 lbf/in (14.00 N/cm)

Weight Loss 20% maximum Loss 80% Solids minimum

ASTM C836; ASTM C 1250

9 to 12% Loss 88 to 92% Solids

Low Temperature Crack Bridging ASTM C836; ASTM C1305 Pass

Extension after heat aging No observable cracking

ASTM C836; ASTM C1522 Pass

Hardness, Type 00 50 Min.

ASTM C836; ASTM D 2240 58 to 64

Maximum V.O.C. Method 310 No more than 95 g/L*

Shelf Life Stability 6 months 12 months

Application Temperature Above 40 °F (5 °C) and rising. If installing below 40 °F (5 °C), please contact Tremco Technical Service at 866-209-2404.

Storage Temperature 40 to 100 °F (5 to 37 °C)

EcoTouch® PINK® FIBERGLAS™ Insulation with PureFiber® Technology

Product Data Sheet

Description Owens Corning™ EcoTouch® Insulation with PureFiber® Technology is flexible insulation made in R-values from 11 to 49. EcoTouch® Insulation is available plain, or faced with either a kraft or foil vapor retarder. The product is manufactured in thicknesses from 31/2" to 14".

Uses EcoTouch® Insulation can be used in a wide range of exterior wall and roof/ceiling applications. The product can be installed in wood or metal framing cavities, or can be installed between furring strips.

Features and Benefits Excellent Thermal Control With the range of R-values and thicknesses available, EcoTouch® Insulation can meet most thermal specifications with ease. The R30C and R38C provide excellent thermal performance in the limited space of cathedral ceilings.

Effective Acoustical Control EcoTouch® Insulation enhances interior noise control by improving the Sound Transmission Class (STC) of walls and floor/ceiling assemblies.

Long Term Performance EcoTouch® Insulation is dimensionally stable and will not slump within the wall cavity. Due to its inorganic fibers, EcoTouch® Insulation will not rot or mildew1 and is noncorrosive to steel, copper, and aluminum.

Easy Installation EcoTouch® Insulation is easy to handle and install. Sized for installation in either wood or metal stud construction, EcoTouch® Insulation can either be friction-fit or stapled into place.

Trimming and fabrication can be done with an ordinary utility knife and is easily installed into odd-shaped cavities and small spaces.

With less dust than other fiberglass insulation products, EcoTouch® Insulation has excellent stiffness and recovery characteristics.2

Designed with the Environment in Mind EcoTouch® Insulation includes a minimum of 50% total recycled content—the highest certified recycled content available in the fiberglass industry.3 EcoTouch® Insulation is GREENGUARD Gold Certified and is verified to be formaldehyde free.4

SpaceSaver Packaging EcoTouch® Insulation is compression packaged in exclusive SpaceSaver packaging from Owens Corning Insulating Systems. SpaceSaver packaging reduces freight and speeds job site handling/installation.

Design Considerations Kraft and standard foil facings on this insulation will burn and must not be left exposed. Install facings in substantial contact with the finish material. Protect from open flame or other heat source.

PROPINK® EcoTouch® Insulation Product Data Width Length Thickness R-Value1

Metal Frame Construction

16" (406mm) 24" (609mm) 48" (1,219mm) 96" (2,438mm) 31/2" (89mm) 11 16" (406mm) 24" (609mm) 48" (1,219mm) 96" (2,438mm) 31/2" (89mm) 13 16" (406mm) 24" (609mm) 96" (2,438mm) 31/2" (89mm) 15 16" (406mm) 24" (609mm) 96" (2,438mm) 51/2" (139mm) 21

Wood Frame Construction Walls

15" (381mm) 23" (584mm) 48" (1,219mm) 93" (2,362mm) 31/2" (89mm) 11 15" (381mm) 23" (584mm) 48" (1,219mm) 93" (2,362mm) 31/2" (89mm) 13 15" (381mm) 23" (584mm) 93" (2,362mm) 31/2" (89mm) 15 15" (381mm) 191/4" 23" (584mm) 48" (1,219mm) 93" (2,362mm) 61/4" (159mm) 19 15" (381mm) 23" (584mm) 93" (2,362mm) 51/2" (139mm) 20 15" (381mm) 23" (584mm) 93" (2,362mm) 51/2" (139mm) 21 15" (381mm) 23" (584mm) 105" (2,667mm) 51/2" (139mm) 21 23" (381mm) 23" (584mm) 93" (2,362mm) 51/2" (139mm) 21

Floor/Ceiling 15" (381mm) 191/4" 23" (584mm) 48" (1,219mm) 93" (2,362mm) 61/4" (159mm) 19 15" (381mm) 23" (584mm) 48" (1,219mm) 63/4" (171mm) 22 15" (381mm) 23" (584mm) 48" (1,219mm) 8" (203mm) 25

151/2" (394mm) 233/4" (603mm) 48" (1,219mm) 81/4" (209mm) 30 16" (406mm) 191/4" 24" (609mm) 48" (1,219mm) 91/2" (241mm) 30

151/2" (394mm) 233/4" (603mm) 48" (1,219mm) 101/4" (260mm) 38 16" (406mm) 24" (609mm) 48" (1,219mm) 12" (305mm) 38 16" (406mm) 24" (609mm) 48" (1,219mm) 14" (356mm) 49

Product Data Sheet with PureFiber® Technology

Buildings utilizing curtainwall construction may be required to be equipped with a sprinkler system to provide adequate fire protection. Check local building codes for specific requirements.

Commercial roof/ceiling thermal applications require that the building envelope block the movement of air from the outdoor environment to the conditioned space. Neither the insulation nor its facing should be relied upon to provide an air barrier. Failure to provide an adequate air barrier could lead to loss of thermal control, discomfort of the building occupants and frozen pipes.

When insulation is added to the inside perimeter of a structure, the area outside the insulation becomes exposed to greater temperature extremes. Check for piping which should be protected against freezing.

The need for and placement of a vapor retarder in commercial construction depends on many factors. The architect or specifier should evaluate the requirements of each project. If a vapor retarder is specified, maintaining the facing integrity may be important for effective moisture/ humidity control. Repair any punctures or tears in the facing by taping. Follow the tape manufacturer’s application recommendations.

Insulation installed too close to light fixtures may affect the luminaire’s performance. Do not install insulation on top of or within 3" of recessed light fixtures unless the fixtures are approved for such use. This is a requirement of the National Electrical Code.

Due to the potential for skin irritation, EcoTouch® Unfaced Insulation should not be used for exposed applications where it will be subject to human contact.

Applicable Standards EcoTouch® Unfaced Insulation is manufactured in compliance with ASTM Standard Specification C665 and is classified noncombustible per ASTM E136.

EcoTouch® Kraft-faced Insulation is manufactured in compliance with ASTM C665, Type II, Class C. EcoTouch® Foil-faced Insulation is manufactured in compliance with ASTM C665, Type III, Class B and C. Federal Specification HH-I-521F has been canceled and is replaced by ASTM C665.

The thermal resistance values for EcoTouch® Insulation were tested in accordance with ASTM C518;

R-value for insulation only.

The surface burning characteristics of EcoTouch® Insulation were derived from products tested in accordance with ASTM E84. This standard is used solely to measure and describe properties of products in response to heat and flame under controlled laboratory conditions, and should not be used to describe or approve the fire hazard of materials under actual fire conditions. However, the results of these tests may be used as elements of a fire risk assessment that takes into account all of the factors pertinent to an assessment of the fire hazard of a particular end use. Values are reported to the nearest five rating.

Technical Data Property (Unit) Value Test

Dimensional Stability (shrinkage) <0.1% ASTM C167

Surface Burning Characteristics (flame spread / smoke developed) Unfaced Kraft faced Foil faced Poly / FSK / PSK faced"

25 / 50

NR / NR

75 / 150 25 / 50

ASTM E84

Critical Radiant Flux (W/cm2) all facings

>0.12

ASTM E970

Water Vapor Permeance (perms) Kraft faced Foil faced Poly faced FSK & PSK faced

1.0 0.5 0.7 0.02

ASTM E96

Water Vapor Sorption (by weight) <5% ASTM C1104

Odor Emission Pass ASTM C1304

Corrosion Resistance Pass ASTM C665, part 13.8

Fungi resistance Pass ASTM C1338

Classifications EcoTouch® Product ICC Building Construction ASTM C665

Unfaced all types Type I

Kraft faced Type III, IV, V Type II, Class C, Cat. 1

Foil faced Type III, IV, V Type III, Class C, Cat. 1 with PureFiber® Technology

Product Data Sheet The vapor retarder permeance of the kraft and foil facings on EcoTouch® Insulation were developed from tests conducted in accordance with ASTM E96, desiccant method.

Installation Between Wood Studs/Rafters EcoTouch® Insulation fits between studs. If required, the flanges can be stapled to either the face or the side of the stud every 8–12" to prevent gaping or “fishmouthing” of the vapor retarder.

EcoTouch® Unfaced insulation can be friction-fit between studs after the cover material has been installed on one side of the cavity.

Use wire or metal straps to hold insulation in place in applications without a cover material, or where the insulation does not fill the depth of the cavity.

Cathedral ceiling products (R30C and R38C) are intended to be friction-fit between rafters.

Cathedral ceiling insulation should be installed to provide a minimum 1" ventilation passageway between the roof deck and insulation. (See Figure 1) It is recommended to use a vent baffle to assure proper clearance.

Between Metal Studs EcoTouch® Insulation can be friction-fit in place until the interior finish is applied. Insulation should fill the cavity and the wall should eventually be closed on both sides. (See Figure 2)

In areas where it will be applied in heights over 8', use wire or metal straps to hold the product in place until the interior finish is applied. When faced insulation is used, the attachment flanges may be taped to the face of the metal stud prior to applying the interior finish. Wire or metal straps should also be used to hold the product in place in applications without a cover material or where the stud depth is larger than the insulation thickness.

Furring Strips EcoTouch® Insulation can be applied between furring strips, hat channels, or Z-shaped furring in areas where a finish surface will be installed. Contact the furring strip manufacturer for appropriate fastening system.

Caution: FIBERGLAS™ insulation may cause temporary irritation to the skin, eyes and respiratory tract. Avoid contact with eyes and skin, wear loose-fitting, long-sleeved clothing, gloves and eye protection when handling and applying the material. Wash with soap and cold water after handling. Wash work clothes separately and wipe out washer.

1" Ventilation Passageway

Figure 1

Figure 2 with PureFiber® Technology

Notes

1. As manufactured, FIBERGLAS™ insulation is resistant to mold growth. However, mold growth can occur on building materials, including insulation, when it becomes contaminated with organic material and when water is present. To avoid mold growth on FIBERGLAS™ insulation, remove any water that has accumulated and correct or repair the source of the water as soon as possible. Insulation that has become wet should be inspected for evidence of residual moisture and contamination, and any insulation that is contaminated should be promptly removed and replaced.

2. According to 2010 clinical trial conducted in Toronto, Canada by Ducker Worldwide on behalf of Owens Corning Insulation Systems, LLC.

3. Certified by Scientific Certifications Systems to have a minimum of 50% recycled glass content, with at least 30% post-consumer recycled and the balance of pre-consumer recycled glass content.

4. Owens Corning™ EcoTouch® Unfaced FIBERGLAS™ insulation is verified to be formaldehyde free by the GREENGUARD Environmental Institute.

OWENS CORNING INSULATING SYSTEMS, LLC

ONE OWENS CORNING PARKWAY

TOLEDO, OHIO, USA 43659

1-800-GET-PINK®

www.owenscorning.com

Pub. No. 10013811-D. Printed in U.S.A. October 2014. THE PINK PANTHER ™ & ©1964–2014 Metro-Goldwyn-Mayer Studios Inc. All Rights Reserved. The color PINK is a registered trademark of Owens Corning. © 2014 Owens Corning.

All Rights Reserved.

Disclaimer of Liability

Technical information contained herein is furnished without charge or obligation and is given and accepted at recipient’s sole risk. Because conditions of use may vary and are beyond our control, Owens Corning makes no representation about, and is not responsible or liable for the accuracy or reliability of data associated with particular uses of any product described herein.

Nothing contained in this bulletin shall be considered a recommendation.

GREENGUARD Certified products are certified to GREENGUARD standards for low chemical emissions into indoor air during product usage. For more information, visit ul.com/gg.

GREENGUARD Indoor Air Quality and GREENGUARD Gold Certified Products applies to EcoTouch® Unfaced Batts, EcoTouch® Faced Batts and Unbonded Loosefill Insulation. GREENGUARD Formaldehyde Free applies to EcoTouch® Unfaced Batts and Unbonded Loosefill Insulation.

GREENGUARD Gold Certified Products applies to Flame Spread 25 FSK Faced;

Flame Spread 25 Extended Flanges PSK Faced; Sound Attenuation Batt Insulation;

Sonobatts® Insulation Unfaced;

Sonobatts® Insulation Kraft-Faced and Metal Building Insulation.

SCS 50% recycled content applies to EcoTouch® Unfaced Batts and Rolls, EcoTouch® Faced Batts and Rolls, Loosefill Insulation, Metal Building Insulation products and Flexible Air Handling products.

Applies to EcoTouch® Unfaced Insulation

MinWool® Sound Attenuation Fire Batts (SAFB)

PRODUCT DATA SHEET

SOUND & FIRE

INSULATION

PERFORMANCE ADVANTAGES

Excellent Acoustical Performance:

Lightweight, fl exible insulation batts are excellent sound absorbers, effi ciently reducing sound transmission. MinWool SAFB improves the Sound Transmission Class (STC) ratings of interior partition walls and suspended ceilings. Batts can improve wall assembly STC ratings by up to 10dB.

Fire Safety: MinWool SAFB has a melting point in excess of 2000˚F (1093˚C). See Applicable Standards for details.

Noncombustible: See Applicable Standards for details.

Durable & Inorganic: MinWool SAFB does not support growth of fungi, nor does it sustain vermin.

ENERGY AND ENVIRONMENT

COMPANY

Johns Manville is committed to creating more comfortable, healthier and energy-effi cient indoor environments. At JM, we believe that in every detail, materials matter.

DESCRIPTION

JM MinWool Sound Attenuation Fire Batt (SAFB) Insulation is made of inorganic fi bers derived from basalt, a volcanic rock. Advanced manufacturing technology ensures consistent product quality, with high-fi ber density and low shot content for excellent performance. MinWool SAFB is inorganic, noncombustible, moisture resistant, non-deteriorating, and will not mildew or support corrosion.

MinWool SAFB is available as an unfaced batt.

USE

MinWool SAFB is designed to deliver noise control in metal stud wall cavities of interior partitions, exterior walls or above suspended ceiling systems.

INSTALLATION

MinWool SAFB is easily cut with a knife for quick installation and snug fi t, even around obstructions and structural members. Butt ends and edges closely together and fi ll all voids with additional insulation.

Install friction-fi t MinWool SAFB between metal wall studs, fi lling the entire cavity to the full height of the wall. Leave no voids.

PACKAGING

MinWool SAFB is compression-packaged for savings in storage and freight costs.

DESIGN CONSIDERATIONS

Acoustical performance of interior drywall partitions can be substantially improved by including a number of important design and construction details. Important details include sealing the perimeter of walls, wall intersection construction considerations, and the location and proper installation of electrical outlets, ducts, doors and mechanical equipment.

LIMITATIONS OF USE

Check applicable building codes.

Technical specifi cations as shown in this literature are intended to be used as general guidelines only. The physical and chemical properties of mineral wool insulation listed herein represent typical, average values obtained in accordance with accepted test methods and are subject to normal manufacturing variations. They are supplied as a technical service and are subject to change without notice. Any references to numerical fl ame spread or smoke developed ratings are not intended to refl ect hazards presented by these or any other materials under actual fi re conditions. Check with the sales offi ce nearest you for current information. All Johns Manville products are sold subject to Johns Manville’s Limited Warranty and Limitation of Remedy. For a copy of the Johns Manville Limited Warranty and Limitation of Remedy or for information on other Johns Manville thermal and acoustical insulation and systems, visit the website or call the 800 number above.

Visit our website at www.JM.com or call 800-654-3103 | 717 17th Street Denver, CO 80202

BID-0163 7/14 © 2014 Johns Manville. All Rights Reserved.

STANDARD SIZES*

THICKNESS WIDTH LENGTH

in (mm) in (mm)

1 (25) 16, 24 (406, 610) 48 (1219) 1½ (38) 16, 24 (406, 610) 48 (1219) 2 (51) 16, 24 (406, 610) 48 (1219) 2½ (64) 16, 24 (406, 610) 48 (1219) 3 (76) 16, 24 (406, 610) 48 (1219)

* Thicknesses of 3½" through 6" are available in ½" increments. Minimum order quantity may apply. Custom sizes are also available on a made-to-order basis.

PRODUCT DATA SHEET SOUND & FIRE INSULATION

ACOUSTICAL PERFORMANCE

ASTM C423 Test Method (Type A Mounting)

THICKNESS

SOUND ABSORPTION COEFFICIENTS

1/3 Octave Band Center Frequencies, Hz in (mm) 125 250 500 1000 2000 4000 NRC 1½ (38) 0.23 0.42 0.89 1.03 1.03 1.03 0.85 2 (51) 0.27 0.55 1.07 1.10 1.10 1.10 0.95 2½ (64) 0.25 0.77 1.10 1.04 0.98 0.98 1.00 3 (76) 0.34 0.92 1.16 1.04 0.98 0.98 1.05 3½ (89) 0.41 1.01 1.20 1.06 1.06 1.05 1.10 4 (102) 0.97 1.28 1.25 1.10 1.10 1.09 1.20

APPLICABLE STANDARDS & BUILDING APPLICATION*

MINWOOL SAFB

ASTM C665 Corrosivity to Steel, Passes ASTM C665 Material Specifi cation, Type 1 ASTM C1104 Water Vapor Sorption, <1% by Weight; <.02% by Volume at 120°F (49°C), 95% RH ASTM C1338 Fungi Resistant, Passes ASTM E84 Flame Spread/Smoke Developed, 5/0 or less ASTM E136 Noncombustible, Passes UL 723, CAN/ULC-S102-M, 5/0 or less CAN4-S114-M, Passes City of New York, MEA-346-90 ICC (International Building Code), All Building Classifi cation Types Nominal Density, 2.5 pcf (40kg/m3) ASTM C518 R-Value at 75°F, 3.7 per inch of thickness

* DISCLAIMER: JM products are designed, manufactured and tested to strict quality standards in our own facilities. This, along with third-party auditing, is your assurance that this product delivers consistent high quality.

MinWool® Sound Attenuation Fire Batts (SAFB) a a aa

PRODUCT DATA SHEET

AP™ FOIL-FACED

PERFORMANCE ADVANTAGES

Thermal Insulation: inch for inch, polyiso has one of the highest energy effi ciencies.

R-values for AP Foil-Faced Foam Sheathing are shown in Table 1, and physical properties are shown in Table 2 (see reverse). R means resistance to heat fl ow. The higher the R-value, the greater the insulating power.

Water-Resistive Barrier: when properly installed as part of a Johns Manville Wall System, AP Foil-Faced Foam Sheathing meets the ICC-ES AC71 acceptance criteria for foam plastic sheathing used as a water-resistive barrier. Please see the installation guide for qualifying assemblies and detailed instructions.

Vapor Barrier: at a minimum thickness of one inch, AP Foil-Faced Foam Sheathing has a vapor permeance of 0.05 perms and qualifi es as a Class I vapor retarder.

Air Barrier: when properly installed as part of a Johns Manville Wall System, AP Foil-Faced Foam Sheathing meets the Air Barrier Association of America boardstock criteria for materials and assemblies. Please see installation guide for qualifying assemblies and detailed instructions.

Noncorrosive: does not accelerate corrosion of pipes, wiring or metal studs.

Lightweight: easy to handle, can be cut with a utility knife or saw.

ENERGY, QUALITY & ENVIRONMENT

DESCRIPTION

Johns Manville AP™ Foil-Faced Foam Sheathing board consists of a uniform closed-cell polyisocyanurate foam core bonded on each side to a foil facer. One side has a refl ective foil facer and the other side has a white non-refl ective foil facer to suit your building needs.

Polyiso provides one of the highest R-values per inch of any rigid insulation (R-6.0 at 1 inch). Furthermore, when properly installed, AP Foil-Faced Foam Sheathing functions as a water-resistive barrier, vapor barrier and air barrier, eliminating the need to install additional components.

AP Foil-Faced Foam Sheathing is produced with an EPA-compliant hydrocarbon-based blowing agent that has zero Ozone Depletion Potential (ODP) and virtually no Global Warming Potential (GWP); it also meets both CFC- and HCFC-free specifi cation requirements. Polyiso is one of North America’s most widely used insulation products and has been cited by the EPA for its responsible impact on the environment.

AP Foil-Faced Foam Sheathing provides exceptional heat, moisture and air control to protect your building’s exterior wall assembly.

INSTALLATION

AP Foil-Faced Foam Sheathing is lightweight and can be easily cut with a utility knife or saw.

Use maximum board lengths to minimize the number of joints. Vertical joints should be staggered.

Butt joints should be centered over framing. To create a water-resistive barrier or an air barrier, treat seams and penetrations as instructed in the installation guide and in accordance with manufacturer’s guidelines.