67071A-PN50244-SBE38-External-Temp-Mount-Kit.pdf

SBE DRAWING: 67071

TITLE: SBE 38 Ext Temp Mount Kit Assembly

REV: .01

Sea-Bird Electronics Procedure

PROCEDURE NUMBER: 67071

TITLE: SBE 38 Ext Temp Mount Kit Assembly

REVISION: A

EFFECTIVE DATE: 03/10/2004

CHECKED BY: _____________ PAGE 1 of 1

SEA -BIRD ELECTRONICS, INC.

1808 136th Place N.E., Bellevue, Washington 98005 USA Telephone: (425) 643-9866 Telex: 292915 SBEI UR Fax: (425) 643-9954 email: seabird@seabird.com

SBE P/N 50244

SBE 38 External Temp Mount Kit, 1” Inline Plumbing

KIT CONTENTS

SBE P/N Manufacturer P/N Primary SBE Application QTY 231580 SBE 38 Temp Plenum Provides water flow to temp probe 1 231581 SBE 38 Temp Plenum Retainer Secures Temp Sensor To Plenum 1 231582 SBE 38 Remote Temp Plug Seals Plenum Retainer opening when not in use 1 30254 Washer, ¼” Split Ring Lock Use with Plenum Hardware (30451) 2 30570 Washer, ¼” Flat SS Use with Plenum Hardware (30451) 2 30809 Morrison seal, .047” hole, Nit Fits in between Plenum and Plenum Retainer 1 31001 Bolt, ¼-20 x 1-3/8 HEX SS Secure Plenum Retainer to Plenum 2 31263 Pipe, 1” Threaded, SS Interface Plenum to plumbing system 2

A. ASSEMBLING THE PLENUM

1. Lubricate the Morrison seal with a Silicone-based lubricant. Never use a Petroleum-based lubricant on SBE o-rings and seals.

2. Clean the Morrison seal surface on the Stainless Steel Plenum (231580) and install the Morrison seal with hole facing out of plenum.

3. Place the Plenum Retainer (231581) so that small hole rests on top of the Morrison Seal.

4. Secure the Retainer to the Plenum with two bolts (31001) and washers (30254, 30570). The lock washer should rest between the bolt head and the flat washer.

5. Wrap plumber’s tape around the threads of the pipes and install into the plenum as needed to make the assembly fit your present plumbing configurations.

B. INSTALLING THE SENSOR

1. Remove the Temperature Probe Guard from SBE 38 sensor.

2. Insert the temperature probe carefully into Plenum Retainer and screw it in until flush.

3. When the sensor is not in use, replace with the remote temperature plug (231582). Be sure to re-install the probe guard onto the SBE 38 before storing or putting it to other uses.

DATE REV REVISION RECORD AUTH DR CHK

10.03 CHANGE ON DRAWING ONLY CB KLP

3.9.04 A CHANGED PN 30452 FOR 31263 CB KLP

D

C

B

AA

B

C

D

12345678

8 7 6 5

10/10/08PC

Old Part/Draw Info N/A

THE INFORMATION CONTAINED IN THIS

WITHOUT THE WRITTEN PERMISSION OF

REPRODUCTION IN PART OR AS A WHOLE

UNLESS OTHERWISE SPECIFIED:

SEA-BIRD ELECTRONICS, INC. ANY

DO NOT SCALE DRAWING

425-643-9866

TOLERANCING PER:

.005

SHARP EDGES

50244

DRAWING IS THE SOLE PROPERTY OF

1808 - 136th PLACE NE, BELLEVUE, WA 98005

SEA-BIRD ELECTRONICS, INC.

MACHINED SURFACES

P/N:

SEA-BIRD ELECTRONICS, INC. IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

N/A

ANSI Y14.5M - 1994

FINISH

N/A

N/A

DRAWN

COMMENTS:

DATENAME

TITLE:

SIZEMATERIAL DWG. NO.

B

REV

SCALE: 2:5

SBE 38 External Temp Plenum Mount Assembly

SHEET 1 OF 1

67071

DIMENSIONS ARE IN INCHES

TOLERANCES:

FRACTIONAL

ANGULAR: 2 BEND

.XX .01 TYP RAD .015

.XXX

INTERPRET GEOMETRIC

DEBUR AND BREAK

.01

DATE REVISION DESCRIPTION AUTH DR CHK

10/10/08 .01 Converted to Solidworks CB PC CB

ITEM

NO.

PART

NO.

DRAWING

NO. DESCRIPTION QTY.

1 231580 21641 SBE38 Temperature Plenum 1 2 231581 21642 SBE38 Temperature Plenum Retainer 1 3 231582 21643 SBE38 Remote Temperature Plug 1 4 30254 N/A Washer, 1/4 Split Ring Lock, SS 2 5 30570 N/A Washer, 1/4" Flat, 960C416, SS 2 6 30809 21018D Morrison Seal .047 ID x .41 OD Nitrile 1 7 31001 N/A Bolt, 1/4-20 x 1 3/8 Hex Hd, SS 2 8 31263 N/A Pipe, 1" NPT x 12", Nipple M-M, 304 SS, SCH40 2

1 2