04-552-20-101 Drawing-1.pdf

NFPA 101 (2018)

PROJECT AREA:

SIXTH FLOOR-SOUTH PROJECT AREA: 16,028 SF

SMOKE COMPARTMENT AREA: 15,728 SF

OCCUPANCY (6.1.5):

EXISTING HOSPITAL: HEALTH CARE OCCUPANCY

OCCUPANT LOAD FACTOR (HEALTH CARE USE, TABLE 7.3.1.2):

INPATIENT TREATMENT DEPARTMENT: 240 SF PER OCCUPANT

SLEEPING DEPARTMENT: 120 SF PER OCCUPANT

PROJECT AREA:

INPATIENT TREATMENT DEPARTMENT: 7,845 SF / 240 = 32.69 OCCUPANTS

SIXTH FLOOR - SOUTH: 7,883 SF / 120 = 65.69 OCCUPANTS

TOTAL OCCUPANTS: = 98.38 OCCUPANTS

FIRE SUPPRESSION:

FULLY SPRINKLERED WITH SMOKE DETECTION

TRAVEL DISTANCE:

DEAD-END LIMIT (18.2.5.2 AND TABLE A.7.6): 30 FEET MAX

COMMON PATH OF TRAVEL (18.2.5.3 AND TABLE A.7.6): 100 FEET MAX

SUITE REMOTE POINT TO EXIT (18.2.5.7.2.4): 200 FEET MAX

TYPE OF CONSTRUCTION:

TYPE I-332

FIRE RESISTANCE RATING (TABLE A.8.2.1.2 AND NFPA 220 TABLE 4.1.4)

EXTERIOR BEARING WALLS: 3 HR

INTERIOR BEARING WALLS: 3 HR - 2 HR FOR SINGLE FLOOR OR ROOF SUPPORT ONLY

STRUCTURAL COLUMNS: 3 HR - 2 HR FOR SINGLE FLOOR OR ROOF SUPPORT ONLY

FLOOR-CEILING ASSEMBLIES: 2 HR

ROOF-CEILING ASSEMBLIES: 1 1/2 HR

INTERIOR NONBEARING WALLS: 0 HR

EXTERIOR NONBEARING WALLS: 0 HR

EXIT ENCLOSURES: (7.1.3.2.1)

EXISTING: 1 HR MIN.

NEW: 2 HR

SHAFT ENCLOSURES: (8.6.5)

CONNECTING 4 STORIES OR MORE: 2 HR

CONNECTING LESS THAN 4 STORIES: 1 HR

SUITE SUBDIVISION: (18.2.5.7.1.4)

SUITE SUBDIVISION PARTITIONS: 0 HR

PROTECTION FROM HAZARDS: (18.3.2)

CENTRAL / BULK LAUNDRIES > 100SF: 1 HR (18.3.2.1.2 - 2)

ROOMS WITH SOILED LINEN > 64 GAL: 1 HR (18.3.2.1.2 - 5)

STORAGE ROOMS > 100SF WITH COMBUSTIBLE MATERIAL: 1 HR (18.3.2.1.2 - 7)

INTERIOR FINISH: (18.3.3 AND TABLE A.10.2.2)

CLASS A

CORRIDOR SEPARATION: (18.3.6)

DAY ROOM: (18.3.6.1)

DAY ROOM SPACE SHALL BE PERMITTED TO BE UNLIMITED IN AREA AND OPEN TO THE

CORRIDOR PER EXCEPTION 1:

(a) SPACE IS NOT USED FOR SLEEPING ROOMS, TREATMENT ROOMS, HAZARDOUS AREAS

(b) SPACE OPENS TO CORRIDOR IN THE SAME SMOKE COMPRATMENT PROTECTED BY

ELECTRICALLY SUPERVISED AUTOMATIC SMOKE DETECTION SYSTEM

(c) OPEN SPACE IS PROTECTED BY ELECTRICALLY SUPERVISED AUTOMATIC SMOKE

DETECTION SYSTEM OR ENTIRE SPACE IS ARRANGED AND LOCATED TO ALLOW

DIRECT SUPERVISION BY THE FACILITY STAFF FROM NURSES' STATION

(d) SPACE DOES NOT OBSTRUCT ACCESS TO REQUIRED EXITS

NURSE STATION: (18.3.6.1 AND A.18.3.6.1(3))

18.3.6.1: CORRIDOR SEPARATION DOES NOT APPLY TO NURSE STATION PER EXCEPTION 3

A.18.3.6.1 (3): TYPICAL NURSE STATION CONTAINS THE FOLLOWING

(1) CHARTING AREA

(2) CLERICAL AREA

(3) NOURISHMENT STATION

(4) MEDICATIONS, MEDICAL EQUIPMENT AND SUPPLIES, CLERICAL SUPPLIES, LINENS

(5) PATIENT MONITORING AND COMMUNICATIONS EQUIPMENT

CONSTRUCTION OF CORRIDOR WALLS (18.3.6.2.3): LIMIT THE TRANSFER OF SMOKE

CORRIDOR DOORS (18.3.6.3.5): SELF-LATCHING WITH POSITIVE LATCHING HARDWARE

PORTABLE FIRE EXTINGUISHERS (9.9):

NFPA 10 (TABLE 6.2.1.1):

TRAVEL DISTANCE : 75 FEET MAX

TYPE: 2-A

MAXIMUM FLOOR AREA: 11,250 SF

SUBDIVISION OF BUILDING SPACE: (18.3.7)

MAX. SMOKE COMPARTMENT AREA (18.3.7.4 (3) (a)): 22,500 SF

MAX. TRAVEL DISTANCE (18.3.7.1 (5)): 200 FEET

SMOKE BARRIER SEPARATION (18.3.7.3): 1 HR FIRE RATED

DOOR IN SMOKE BARRIER (18.3.7.6): *20 MINUTE MIN.

*OR DOOR OF SUBSTANTIAL CONSTRUCTION

BUILDING CODES / PROJECT MANUALS

NFPA 10 PORTABLE FIRE EXTINGUISHERS 2018

NFPA 70 NATIONAL ELECTRICAL CODE 2020

NFPA 99 HEALTH CARE FACILITIES CODE 2018

NFPA 101 LIFE SAFETY CODE 2018

PG-18-3 DESIGN AND CONSTRUCTION PROCEDURES JULY 2004

PG-18-5 EQUIPMENT GUIDE LIST FEBRUARY 2018

PG-18-12 DESIGN GUIDE (MENTAL HEALTH FACILITIES) DECEMBER 2017

PG-18-13 VA BARRIER FREE DESIGN STANDARD JANUARY 2017

PG-18-14 PROGRAM GUIDE (ROOM FINISHES, DOOR, & HARDWARE SCHEDULE) APRIL 2017

PG-18-15 MINIMUM REQUIREMENTS FOR A/E SUBMISSIONS MAY 2006

HVAC DESIGN MANUAL MAY 2019

PLUMBING DESIGN MANUAL MAY 2018

FIRE PROTECTION DESIGN MANUAL DECEMBER 2015

PHYSICAL SECURITY DESIGN MANUAL JANUARY 2015

PROJECT NUMBER:

SUBMITTAL FOR:

DRAWING INDEX: CODE DATA:LOCATION MAP:

VA DAYTON RENOVATE MENTAL HEALTH

6TH FLOOR

552-20-101

BID AND CONSTRUCTION

4100 WEST THIRD STREET,

DAYTON, OHIO 45428

P R

ELI

M

IN

AR

Y

N O

T F O

R

C O

N S

TR

U C

TIO

N

C B

LH

D E

SIG

N

IN

C

VA FORM 08 - 6231

F

E

D

C

B

A

987654321 10

F

E

D

C

B

A

987654321 10

BID AND CONSTRUCTION

Project Number

Building Number

Drawing Number

VA Building 330

Project Title

Location

Issued Date Checked Drawn

Drawing Title

Approved: Project Director

Phase

FULLY SPRINKLERED

Office of Construction and Facilities Management

STAMPARCHITECT / ENGINEER OF RECORD

7850 Freeway Circle

440.243.2000 t

Cleveland, OH 44130

440.243.3305 f

CONSULTANT

SCHEESER BUCKLEY MAYFIELD

1540 CORPORATE WOODS PARKWAY

UNIONTOWN, OHIO 44685

MECHANICAL ENGINEER

ELECTRICAL ENGINEER

/6 /2

:1

:3

P

M C

R e v it L o c a l\

M e n ta l H e a lt h F lo o r

C e n tr a l_

R

C e n tr a l_ rb o u k z a m

.r v t

GI-100

552-20-101

MS CE

VA DAYTON RENOVATE MENTAL

HEALTH 6TH FLOOR

09/20/2021

4100 WEST THIRD STREET, DAYTON, OHIO 45428

COVER SHEET

GENERAL

GI-100 COVER SHEET

GI-101 NOTES AND SYMBOLS

GI-102 SIXTH FLOOR LIFE SAFETY PLAN

GI-103 PENETRATION FIRE STOPPING DETAILS

GI-104 PENETRATION FIRE STOPPING DETAILS

GI-105 PENETRATION FIRE STOPPING DETAILS

GI-106 PENETRATION FIRE STOPPING DETAILS

ARCHITECTURAL

AD-200 SIXTH FLOOR DEMOLITION PLANS

AE-300 SIXTH FLOOR DIMENSION PLAN

AE-301 SIXTH FLOOR EQUIPMENT PLAN

AE-302 SIXTH FLOOR PATTERN PLAN

AE-303 SIXTH FLOOR SIGNAGE PLAN

AE-500 BUILDING SECTIONS

AE-510 INTERIOR DETAILS

AE-511 INTERIOR DETAILS

AE-600 ENLARGED PLANS AND ELEVATIONS (FURNITURE SHOWN FOR REFERENCE)

AE-601 ENLARGED PLANS AND ELEVATIONS

AE-602 ENLARGED PLANS AND ELEVATIONS

AE-603 ENLARGED PLANS AND ELEVATIONS

AE-604 ENLARGED PLANS AND ELEVATIONS

AE-700 ROOM FINISH SCHEDULE AND DETAILS

AE-710 MILLWORK DETAILS

AE-711 MILLWORK DETAILS - NURSE STATION

AE-800 INTERIOR ELEVATIONS

AE-801 INTERIOR ELEVATIONS

AE-810 INTERIOR PERSPECTIVES

AE-900 SIXTH FLOOR REFLECTED CEILING PLANS

AE-910 SIXTH FLOOR REFLECTED CEILING PLAN - ALTERNATE

AE-1000 DOOR SCHEDULE AND DETAILS

AE-1001 INTERIOR SIGN SCHEDULE

AE-1010 PARTITION TYPES

FIRE PROTECTION

FJ-100 FIRE SUPPRESSION GENERAL NOTES, SYMBOL LEGEND, AND DETAILS

FX-100 NEW WORK - SIXTH FLOOR PLAN - FIRE SUPPRESSION

PLUMBING

PD-100 DEMOLITION - FIFTH FLOOR PLAN - PLUMBING (SANITARY)

PD-101 DEMOLITION - SIXTH FLOOR PLAN - PLUMBING (SANITARY)

PD-102 DEMOLITION - SIXTH FLOOR PLAN - PLUMBING (WATER AND MEDICAL GAS)

PL-100 NEW WORK - FIFTH FLOOR PLAN - PLUMBING (SANITARY)

PL-101 NEW WORK - SIXTH FLOOR PLAN - PLUMBING (SANITARY)

PL-102 NEW WORK - SIXTH FLOOR PLAN - PLUMBING (WATER)

PJ-100 PLUMBING GENERAL NOTES, SYMBOL LEGEND, AND SCHEDULES

PJ-101 DETAILS - PLUMBING

MECHANICAL

MD-100 DEMOLITION - SIXTH FLOOR PLAN - HVAC (DUCTWORK)

MD-101 DEMOLITION - SIXTH FLOOR PLAN - HVAC (PIPING)

MH-100 NEW WORK - SIXTH FLOOR PLAN - HVAC (DUCTWORK)

MI-100 MECHANICAL TEMPERATURE CONTROLS

MP-100 NEW WORK - SIXTH FLOOR PLAN - HVAC (PIPING)

MJ-100 MECHANICAL GENERAL NOTES AND SYMBOL LEGEND

MJ-101 MECHANICAL DETAILS

MJ-102 MECHANICAL SCHEDULES

Revisions Date

BID AND CONSTRUCTION 10/06/2025

ELECTRICAL

ED-100 DEMOLITION - SIXTH FLOOR PLAN - ELECTRICAL

EL-100 LIGHTING - SIXTH FLOOR PLAN - ELECTRICAL

EL-101 LIGHTING - SIXTH FLOOR PLAN ALTERNATE - ELECTRICAL

EP-100 POWER - SIXTH FLOOR PLAN - ELECTRICAL

ET-100 TELECOM - SIXTH FLOOR PLAN - ELECTRICAL

EY-100 SYSTEMS - SIXTH FLOOR PLAN - ELECTRICAL

EJ-100 ELECTRICAL SYMBOL LEGEND AND GENERAL NOTES

EJ-101 LIGHTING SCHEDULE AND DETAILS

EJ-102 ELECTRICAL DETAILS

EJ-103 RISER DIAGRAM AND SCHEDULES

EJ-104 PANELBOARD SCHEDULES

EJ-105 PANELBOARD SCHEDULES

EK-100 TELECOMMUNICATIONS DETAILS

EK-101 TELECOM ROOM DETAILS

EK-102 TELECOMMUNICATIONS GROUNDING AND PATHWAY DETAILS

EK-103 ELECTRICAL SYSTEMS DETAILS

EK-104 ELECTRICAL SYSTEMS DETAILS

AIR CONDITIONED

ACOUSTICAL CEILING TILE

AIR CONDITIONING UNIT

ABOVE FINISHED FLOOR

ALTERNATE

AUDIO VISUAL

ARCHITECTURAL WOODWORK

AC

A.C.T.

A.C.U.

A.F.F.

ALT

A.V.

A.W.

BD

BLDG

BLK

BLKG

BOT

BR

BRG

BSMT

CONC

CAB

CBB

C.C.T.

C.G.

C.J.

CL.

CLG

C.M.U.

COL

COMM

CONF

CONN

CONST

CONT

CONTR

COORD

CORR

C.R.

C.W.

CYL

D. ALT.

DBL

DEMO

DET

D.F.

DIA

DIAG

DIM

DISP

DN

DR

D.S.

D.W.

DWG(S)

EXIST

E

EA EACH

EAST

EXISTING

DRAWING(S)

DUMBWAITER

DOWNSPOUT

DOOR

DOWN

DISPENSER

DIMENSION

DIAGONAL

DIAMETER

DRINKING FOUNTAIN

DETAIL

DEMOLITION

DOUBLE

DEDUCT ALTERNATE

CYLINDER

COLD WATER

CRASH RAIL

CORRIDOR

COORDINATE

CONTRACTOR

CONTINUOUS

CONSTRUCTION

CONNECTION

CONFERENCE

COMMUNICATION

COLUMN

CONCRETE MASONRY UNIT

CEILING

CLOSET

CONTROL JOINT

CORNER GUARD

CUBICAL CURTAIN TRACK

CEMENTITIOUS BACKER BOARD

CABINET

CONCRETE

BASEMENT

BEARING

BRICK

BOTTOM

BLOCKING

BLOCK

BUILDING

BOARD

POUND OR NUMBER #

DIAMETER OR ROUND

CENTERLINE

AT

ANGLE

AND

EXPANSION JOINT

ELECTRICAL

E.I.F.S.

E.J.

ELECT

EL

ELEV

EMER

ENCL

EQ

EQUIP

E.T.R.

EVAC

E.W.C.

EXT

F.B.

F.C.

F.C.U.

F.D.

F.D.V.C.

F.E.

F.E.C.

F.H.C.

FIN

FIXT

FLR

FLEX

FLUOR

F.R.T.

FT

FTG

FURN

FUT

G

GA

GALV

G.C.

G.F.M.U.

GL

GR

GRND

GWB

H.B.

HD

HDWD

H.M.

HOSP

H.P.

HR

H.R.

HORIZ

HT

HTG

HTR

H.V.A.C.

H.W.

HW

HYD

I.D.

ILLUM

INCIN

INCAND

INCL

INFO

INSUL

INT

I.P.S.

ISOL

IV

JT

KITCH

K.O.

K.P.

K.S. KNEE SPACE

KICK PLATE

KNOCK OUT

KITCHEN

JOINT

INTRAVENOUS

ISOLATION

INSIDE PIPE SIZE

INTERIOR

INSULATION

INFORMATION

INCLUDE

INCINERATOR

INCANDESCENT

ILLUMINATION

INSIDE DIAMETER (DIM)

HYDRANT

HARDWARE

HOT WATER

HEATING, VENTILATION, AIR CONDITIONING

HEATER

HEATING

HEIGHT

HORIZONTAL

HANDRAIL

HOUR

HIGH POINT

HOSPITAL

HOLLOW METAL

HEAD

HOSE BIBB

GYPSUM WALL BOARD

GROUND

GRADE

GLASS

GROUND FACE MASONRY UNITS

GENERAL CONTRACTOR

GALVANIZED

GAGE

GAS

FUTURE

FURNITURE

FOOTING

FOOT OR FEET

FIRE RESISTANT TREATED

FLUORESCENT

FLEXIBLE

FLOOR

FIXTURE

FINISH

FIRE HOSE CABINET

FIRE EXTINGUISHER CABINET

FIRE EXTINGUISHER

FIRE DEPARTMENT VALVE CABINET

FLOOR DRAIN

FAN COIL UNIT

FOOT CONTROL

FACE BRICK

EXTERIOR

ELECTRIC WATER COOLER

EVACUATION

EXISTING TO REMAIN

EQUIPMENT

EQUAL

ENCLOSURE

EMERGENCY

ELEVATOR

ELEVATION

L

LAB

LAM

LIB

LIN

LOC

L.P.

LT.WT.

LTG

MACH

MAS

MATL

MAX

MECH

MED

MED.CAB.

MEMB

MEZZ

MFR

MH

MIN

MISC

MKR.BD.

MLDG

M.O.

MOD

M.R.G.B.

MTD

MTL

N

N.C.

NEG

N.I.C.

NO

N.T.S.

O

O.C.

O.D.

OFF.

OPNG

OPP

O.F.C.I.

PART.BD.

P.C.

P.C.D.

PERIM

PERP

PLWD

PORT

PR

PREFAB

PREFIN

PROJ

PROP

P.T.

PTD

R

R.A.

REC

RECEP

RECT

REF REFRIGERATOR

RECTANGULAR

RECEPTACLE

RECESSED

RETURN AIR

RADIUS

PAINTED

PNEUMATIC TUBE

PROPERTY

PROJECT

PREFINISHED

PREFABRICATED

PAIR

PORTABLE

PLYWOOD

PERPENDICULAR

PERIMETER

PAPER CUP DISPENSER

PRECAST CONCRETE

PARTICLEBOARD

OWNER FURNISHED, CONTRACTOR INSTALLED

OPPOSITE

OPENING

OFFICE

OUTSIDE DIAMETER(DIM)

ON CENTER

OXYGEN

NOT TO SCALE

NOMINAL

NUMBER

NOT IN CONTRACT

NEGATIVE

NURSE CALL

NITROGEN/NORTH

METAL

MOUNTED

MOISTURE RESISTANT GYPSUM BOARD

MODIFIED, MODULAR

MASONRY OPENING

MOULDING

MARKERBOARD

MISCELLANEOUS

MINIMUM

MANHOLE

MANUFACTURER

MEZZANINE

MEMBRANE

MEDICINE CABINET

MEDICINE/MEDICAL

MECHANICAL

MAXIMUM

MATERIAL

MASONRY

MACHINE

LIGHTING

LIGHTWEIGHT

LOW POINT

LOCATION/LOCATE

LINEAR

LIBRARY

LAMINATE

LABORATORY

LOCK

REFL REFLECTED

REINF REINFORCED

REM REMOVABLE

REQ'D REQUIRED

REV REVISION

R.F. RADIO FREQUENCY

RM

RND

R.O.

R.S.T. RUBBER STAIR TREADS

ROUGH OPENING

ROUND

S

S.S.

S.A.

SAN

SCHED

S.C.R.

S.D.

SECT

SGL

SH

SHR

SHT

SIM

S.O.G.

SPEC (S)

S&R

S.P.T.

SQ

S.F.

S.I.

S.Y.

S.T.C.

STD

STL

STOR

STRUCT

SURF

SUSP

T

T&B

T&G

TAN

TEL

TEMP

THRESH

THRU

TK.BD.

TLT

T.O.P.

TV

TYP

U.C.

UNFIN

U.N.O.

UTIL

V, VAC

VENT

VERT

VEST

VIT

W

W/

W/O

W.C.

W/C

WD

W.P.

YD YARD

WORKPOINT

WOOD

WHEEL CHAIR

WATER CLOSET

WITHOUT

WITH

WEST/WATER

VITREOUS

VESTIBULE

VERTICAL

VENTILATION

VACUUM

UTILITY

UNLESS NOTED OTHERWISE

UNFINISHED

UNDER COUNTER

TYPICAL

TELEVISION

TOP OF PAVEMENT

TOILET

TACKBOARD

THROUGH

THRESHOLD

TEMPERATURE

TELEPHONE

TANGENT

TONGUE AND GROOVE

TOP AND BOTTOM

THERMOSTAT

SUSPENDED

SURFACE

STRUCTURAL

STORAGE

STEEL

STANDARD

SOUND TRANSMISSION CLASS / COEFFICIENT

SQUARE YARD

SQUARE INCH

SQUARE FOOT

SQUARE

SPECIMEN PASS-THRU

SHELF & ROD

SPECIFICATION(S)

SLAB ON GRADE

SIMILAR

SHEET

SHOWER

SHELVING, SHELF

SINGLE

SECTION

SUPPLY DIFFUSER

SHOWER CURTAIN ROD

SCHEDULE

SANITARY

SUPPLY AIR

STAINLESS STEEL

SOUTH

LT LIGHT

LAV LAVATORY

W.W.F. WELDED WIRE FABRIC

EXTERIOR INSULATION FINISH SYSTEM

HARDWOOD

NOM

ROOM

V.I.F. VERIFY IN FIELD

ALUMINUMAL

F.P. FIRE PROTECTION

F.P.G. FIRE PROTECTED GLAZING

CL

O.F.O.I. OWNER FURNISHED, OWNER INSTALLED SSM SOLID SURFACE MATERIAL

BRK BREAK

CLR CLEAR

DEPT DEPARTMENT

GB GYPSUM BOARD

GYP GYPSUM

MGR. MANAGER

S.W. SOCIAL WORKER

T.R. TOILET ROOM

W/D WASHER / DRYER

NOTE: ALL ITEMS/MATERIALS MAY NOT OCCUR IN THIS PROJECT. LIST

PROVIDED FOR REFERENCE ONLY.

UNDISTURBED EEARTH OR

UNDISTURBED SUBGRADE

COMPACTED EARTH OR

COMPACTED SUBGRADE

ROCK

POROUS FILL OR SUBBASE

IMPERVIOUS FILL

DRAINAGE FILL

CAST-IN-PLACE CONCRETE

PRECAST CONCRETE

TOPSOIL

CEMENTITIOUS DECKS AND

TOPPINGS

GROUT

BRICK

GLAZED BRICK

STRUCTURAL CLAY TILE

UNIT MASONRY

GLAZED STRUCTURAL CLAY TILE

UNIT MASONRY

CONCRETE UNIT MASONRY

GLAZED CONCRETE UNIT MASONRY

GLAZED UNIT MASONRY

CUT STONE

FIREBRICK

CAST STONE

STEEL

ALUMINUM

ORNAMENTAL

METAL/STAINLESS STEEL

CONTINUOUS WOOD FRAMING

WOOD BLOCKING

PLYWOOD

PARTICLE BOARD

FINISHED LUMBER FOR

ARCHITECTURAL WORK

BATT INSULATION

RIGID INSULATION

LOOSE FILL INSULATION

EXTERIOR INSULATION AND

FINISH SYSTEM

FIBROUS FIRE SAFING

GLASS

CARPET

LATH AND PLASTER

GYPSUM BOARD

PLASTIC GLAZING

TERRAZZO

ACOUSTICAL CEILING

RESILIENT TILE

CERAMIC TILE

FINISHED CONTOURS

EXISTING CONTOURS

CONTRACT LIMIT LINE

PROPERTY LINE

ELEVATION INDICATORS

FINISH ELEVATION

EXISTING ELEVATION

FENCE

STRUCTURAL GRID COLUMN TAG (NEW)

STRUCTURAL GRID COLUMN TAG (EXISTING)

CENTERLINE

REVISION INDICATOR

DRAWING BREAK LINE

MATCH LINE INDICATOR

HIDDEN LINE

1. ITEMS ABOVE OR BEYOND

2. ITEMS NOT IN CONTRACT (N.I.C.)

3. ITEMS BEING DEMOLISHED

ELEVATION DATUM

WINDOW & LOUVER SYMBOL

(SEE WINDOW SCHEDULE)

DOOR SYMBOL

(SEE DOOR SCHEDULE)

EQUIPMENT SYMBOL

(SEE EQUIPMENT SCHEDULE)

WALL TYPE SYMBOL

(SEE PARTITION TYPES)

PARTITION NUMBER

WORK POINT

ROOM NUMBER SYMBOL

ELEVATION VIEW INDICATOR

DETAIL INDICATOR

SECTION INDICATOR

DRAWING TITLE

1 View Name

SCALE:1/8" = 1'-0"A101

DETAIL NO.

DRAWING NO.

1'-0"

1'-0"

INTERIOR 01

INTERIOR 02

ELEVATION NO.

DRAWING NO. A101

ELEVATION NO.

A

A

NEW

EXISTING

SECTION NO.

DRAWING NO.

X

B

Room name

X

/1 A101

/1 A101

A101

A101

NEW PARTITION

PATCH TO MATCH EXISTING PARTITION

EXISTING PARTITION TO REMAIN

EXISTING DOOR TO REMAIN

EXISTING DOOR TO BE REMOVED

NEW DOOR AND FRAME

POCKET DOOR

CASED OPENING

BIFOLD DOOR

SLIDING DOOR

Room name

Room name

P R

ELI

M

IN

AR

Y

N O

T F O

R

C O

N S

TR

U C

TIO

N

C B

LH

D E

SIG

N

IN

C

VA FORM 08 - 6231

F

E

D

C

B

A

987654321 10

F

E

D

C

B

A

987654321 10

BID AND CONSTRUCTION

Project Number

Building Number

Drawing Number

VA Building 330

Project Title

Location

Issued Date Checked Drawn

Drawing Title

Approved: Project Director

Phase

FULLY SPRINKLERED

Office of Construction and Facilities Management

STAMPARCHITECT / ENGINEER OF RECORD

7850 Freeway Circle

440.243.2000 t

Cleveland, OH 44130

440.243.3305 f

CONSULTANT

SCHEESER BUCKLEY MAYFIELD

1540 CORPORATE WOODS PARKWAY

UNIONTOWN, OHIO 44685

MECHANICAL ENGINEER

ELECTRICAL ENGINEER

/6 /2

:1

:3

P

M C

R e v it L o c a l\

M e n ta l H e a lt h F lo o r

C e n tr a l_

R

C e n tr a l_ rb o u k z a m

.r v t

GI-101

552-20-101

MS CE

VA DAYTON RENOVATE MENTAL

HEALTH 6TH FLOOR

09/20/2021

4100 WEST THIRD STREET, DAYTON, OHIO 45428

NOTES AND SYMBOLS

STANDARD ABBREVIATIONS

MATERIALS LEGEND LEGEND_GRAPHIC SYMBOLS

FLOOR PLAN LEGEND

Revisions Date

BID AND CONSTRUCTION 10/06/2025

F

1 1

1.2

F1

F6 G

G

B3

B3

B6

B6

C5

C5 D3

E1

E6

G6 H

H

H9

H9

J

J

K

K

J8

J8

K8

K8

L

L

L3

L3

L7 N

N

1.5

1.7 1.7

2.2

3.2

4.1

5 5

5.3

6 6

7 7

8 8

11 11

11.2

12 12

K7J7D8

5.6

6.6

7.4

8.9

9.8

D2

D2

B7

10.7

11.8

11.5

C2

C2

G9

K6

K6

10.6

2.3

L6

L6

E11

E11

H8G8

TRAVEL DISTANCE

176'-11" TO EXIT

TRAVEL DISTANCE

143'-1" TO EXIT

36'-9" COMMON

PATH OF TRAVEL

O

VERALL DIAG

O

NAL D

ISTANCE

210' - 11"

EXIT SEPARATION DISTANCE

157' - 5"

EXTENT OF SMOKE

COMPARTMENT

15,728 SF

F.E.C.

F.E.C.

F.E.C.

E7

E7

BELONGINGS

UTILITY ROOM

6D-101

OFF

6D-104

CONFERENCE

6D-102

RES. OFF.

6D-103

CHECK IN

6D-100

INTERVIEW

6D-133

EXAM

6D-134

EQUIPMENT

6D-111

TRASH

6D-152

ELECTRICAL CL.

6D-153

COMM CL.

6D-154

CONFERENCE

ROOM

6D-116

STUDENT OFF.

6D-115

BRK

6D-114

T.R.

6D-112

S.W.

6D-150 S.W.

6D-149

SOILED UTIL &

LINEN

6D-151

NURSE MGR.

6D-109

ALCOVE

6D-107

TELECOM

6D-106

EXERCISE

6D-143

C L E

A N

L

IN

E N

D

-1

M E

D

IC

A T

IO

N

D

-1

SERVERY

6D-105

VISITOR/CONSULT

6D-132

MULTI-PURPOSE

6D-142

JC

6D-110

T.R.

6D-113

CORRIDOR

6C-5

DAY ROOM

6D-141

CORRIDOR

6C-6

N O

U R

IS

H

M E

N T

D

-1

OFF

6D-108

SALLY PORT

6C-3

BARIATRIC

PATIENT ROOM

6D-131

PATIENT ROOM 2

6D-130

PATIENT ROOM 3

6D-129

PATIENT ROOM 4

6D-128

PATIENT ROOM 5

6D-127

PATIENT ROOM 6

6D-126

PATIENT ROOM 7

6D-125

PATIENT ROOM 8

6D-124

T.R.

6D-131A

T.R.

6D-130A

T.R.

6D-129A

T.R.

6D-128A

T.R.

6D-127A

T.R.

6D-126A

T.R.

6D-124A

WOMEN'S

LOUNGE

6D-138

W/D

6D-137

PATIENT ROOM 9

6D-123

PATIENT ROOM 10

6D-122

PATIENT ROOM 11

6D-121

PATIENT ROOM 12

6D-120

PATIENT ROOM 13

6D-119

T.R.

6D-123A T.R.

6D-122A

T.R.

6D-121A T.R.

6D-120A

T.R.

6D-119A

STORAGE

6D-135

CORRIDOR

6C-8

QUIET

6D-136

T.R.

6D-125A

J.C.

6D-130B

NURSE STATION

6D-144

CORRIDOR

6C-4

SITTING

6D-140

CORRIDOR

6C-7

F.E.C.

F.E.C.

CONSTRUCTION LIMIT LINE

CONSTRUCTION

LIMIT LINE

F9

F9

FLEX ROOM

6D-118

RESTRAINT

6D-117

UTIL RM

6D-117B

FLEX T.R.

6D-118A

F.E.C.

SOUND CLOSET

6D-126B

1 HR FIRE

SEPARATION

1 HR FIRE

SEPARATION

1 HR FIRE

SEPARATION

2 HR FIRE

SEPARATION

C L E

A N

U T

IL

IT

Y

D

-1

STORAGE

6D-155

CORRIDOR

C6-4

TRAVEL DISTANCE

96'-0" TO EXIT

TRAVEL DISTANCE

124'-6" TO EXIT

TEMPORARY 1 HOUR

RATED CONSTRUCTION

PARTITION AND DOOR T1

2 HR FIRE

SEPARATION

NON-RATED SMOKE PARTITION

1 HR FIRE SEPARATION

2 HR FIRE SEPARATION

TRAVEL DISTANCE

EXIT SIGN

FIRE EXTINGUISHER CABINETF.E.C.

TEMPORARY 1-HOUR RATED

PARTITION TO BE REMOVED BY

CONTRACTOR AT PROJECT

COMPLETION. SEE PARTITION

TYPE 'T1' ON SHEET AE-1010.

P R

ELI

M

IN

AR

Y

N O

T F O

R

C O

N S

TR

U C

TIO

N

C B

LH

D E

SIG

N

IN

C

VA FORM 08 - 6231

F

E

D

C

B

A

987654321 10

F

E

D

C

B

A

987654321 10

BID AND CONSTRUCTION

Project Number

Building Number

Drawing Number

VA Building 330

Project Title

Location

Issued Date Checked Drawn

Drawing Title

Approved: Project Director

Phase

FULLY SPRINKLERED

Office of Construction and Facilities Management

STAMPARCHITECT / ENGINEER OF RECORD

7850 Freeway Circle

440.243.2000 t

Cleveland, OH 44130

440.243.3305 f

CONSULTANT

SCHEESER BUCKLEY MAYFIELD

1540 CORPORATE WOODS PARKWAY

UNIONTOWN, OHIO 44685

MECHANICAL ENGINEER

ELECTRICAL ENGINEER

/6 /2

:1

:4

P

M C

R e v it L o c a l\

M e n ta l H e a lt h F lo o r

C e n tr a l_

R

C e n tr a l_ rb o u k z a m

.r v t

GI-102

552-20-101

MS CE

VA DAYTON RENOVATE MENTAL

HEALTH 6TH FLOOR

09/20/2021

4100 WEST THIRD STREET, DAYTON, OHIO 45428

SIXTH FLOOR LIFE SAFETY PLAN

SCALE: 1/16" = 1'-0"GI-102

1 SIXTH FLOOR LIFE SAFETY PLAN

LIFE SAFETY LEGEND

++ L RATING APPLIES ONLY TO CP 680-P DEVICES AND ONLY WHEN THE NOM DIAM OF PIPE EQUALS SIZE OF DEVICE (2 IN.

DIAM PIPE IN 2" DEVICE ETC.) L RATING DOES NOT APPLY TO CP 680N DEVICES.

4. FIRESTOP DEVICE* — (NOT SHOWN) -TOP SEAL PLUG FOR USE WITH CP 680-75/2.5"N DEVICES AND NOM PIPE OR CONDUIT SIZES 3/4 IN. (19 MM) TO 2 IN. (51 MM), INSTALLED IN ACCORDANCE WITH THE MANUFACTURER\'S INSTRUCTIONS. THE TOP SEAL PLUG IS OPTIONAL FOR NOM 1-1/2 IN. (38 MM) PIPES AND CONDUITS. TOP SEAL PLUGS ARE REQUIRED FOR ALL PIPES AND CONDUITS LESS THAN NOM 1-1/2 IN. (38 MM). W RATING APPLIES ONLY WHEN THE CPS OR IPS TOP SEAL PLUGS ARE

USED.

4A. FIRESTOP DEVICE* - WATER BARRIER MODULE — (OPTIONAL, NOT SHOWN) - APPLIES TO NOM 2", 3" AND 4" WATER BARRIER MODULES USED IN COMBINATION WITH THE CP 680-P 2", CP 680-P 3" AND CP 680-P 4" DEVICES, RESPECTIVELY, AND SUPPLIED BY DEVICE MANUFACTURER. MODULE IS THREADED ONTO TOP OF DEVICE. W RATING APPLIES ONLY WHEN

WATER BARRIER MODULE IS USED.

*BEARING THE UL CLASSIFICATION MARK

+BEARING THE UL LISTING MARK

1. FLOOR ASSEMBLY — MIN 2-1/2 IN. (64 MM) THICK REINFORCED LIGHTWEIGHT OR NORMAL WEIGHT (100-150 PCF

OR 1600-2400 KG/M3) CONCRETE.

1A. FLOOR ASSEMBLY - (OPTIONAL - NOT SHOWN) — THE FIRE RATED UNPROTECTED CONCRETE AND STEEL FLOOR ASSEMBLY SHALL BE CONSTRUCTED OF THE MATERIALS AND IN THE MANNER SPECIFIED IN THE INDIVIDUAL

D900 SERIES DESIGNS IN THE UL FIRE RESISTANCE DIRECTORY AND AS SUMMARIZED BELOW:

A. CONCRETE — MIN 2-1/2 IN (64 MM) THICK REINFORCED LIGHTWEIGHT OR NORMAL WEIGHT (100-150 PCF

OR 1600-2400 KG/M3) CONCRETE.

B. STEEL FLOOR AND FORM UNITS* — COMPOSITE OR NON-COMPOSITE MAX 3 IN. (76 MM) DEEP GALV STEEL

FLUTED UNITS AS SPECIFIED IN THE INDIVIDUAL FLOOR-CEILING DESIGN.

2. FIRESTOP DEVICE* — CAST IN PLACE FIRESTOP DEVICE PERMANENTLY EMBEDDED DURING CONCRETE PLACEMENT OR GROUTED IN CONCRETE ASSEMBLY IN ACCORDANCE WITH ACCOMPANYING INSTALLATION INSTRUCTIONS. THE 3, 4 AND 6 IN. DEVICES MAY EXTEND A MAX 2 IN. (51 MM) ABOVE THE TOP SURFACE OF THE CONCRETE. THE MAX EXTENSION ABOVE THE SLAB FOR THE 2 AND 2.5 IN. DEVICES IS NOT RESTRICTED.

3. THROUGH PENETRANTS — ONE NONMETALLIC PIPE OR CONDUIT TO BE INSTALLED WITHIN THE FIRESTOP SYSTEM. PIPE OR CONDUIT TO BE RIGIDLY SUPPORTED ON BOTH SIDES OF FLOOR ASSEMBLY. FOR W RATING WITH WATER BARRIER MODULE, PIPE SHALL BE INSTALLED FROM BOTTOM OF DEVICE. THE FOLLOWING TYPES

AND SIZES OF NONMETALLIC PIPES OR CONDUITS MAY BE USED:

A. POLYVINYL CHLORIDE (PVC) PIPE — NOM 6 IN. (152 MM) DIAM (OR SMALLER) SCHEDULE 40 SOLID OR CELLULAR CORE PVC PIPE FOR USE IN CLOSED (PROCESS OR SUPPLY) OR VENTED (DRAIN, WASTE OR

VENT) PIPING SYSTEMS.

B. CHLORINATED POLYVINYL CHLORIDE (CPVC) PIPE — NOM 6 IN. (152 MM) DIAM (OR SMALLER) SDR11 OR

SDR13.5 CPVC PIPE FOR USE IN CLOSED (PROCESS OR SUPPLY) PIPING SYSTEMS.

C. RIGID NONMETALLIC CONDUIT+ — NOM 6 IN. (152 MM) DIAM (OR SMALLER) SCHEDULE 40 PVC CONDUIT

INSTALLED IN ACCORDANCE WITH THE NATIONAL ELECTRICAL CODE (NFPA NO. 70).

THE FIRESTOP DEVICES AND NONMETALLIC PENETRANTS SHALL BE SIZED AS FOLLOWS:

NOM PIPE DIAMETER FIRESTOP DEVICE

CP 680-75/2.5"N

CP 680 -P 2"

CP 680-P 3"

CP 680-1 10/4"N

CP 680-P 4"

CP 680-160/6"N

CP 680-P 6"

1/2 IN. TO 2 IN. (19 MM TO 51 MM)

3 IN.(76 MM)

3 IN. TO 4 IN. (76 MM TO 102 MM)

6 IN. (152 MM)

2 3

A

A

SECTION A-A

C R

CLASSIFIED BY

UNDERWRITERS

LABORATORIES, INC.

TO UL 1479 AND CAN/ULC-

S115

US SYSTEM NO. F-A-2053

F RATING - 2 HR

T RATING - 0 HR

L RATING AT AMBIENT - LESS THAN 1 CFM/SQ FT (SEE ITEM 3)

L RATING AT 400 F - LESS THAN 1 CFM/SQ FT (SEE ITEM 3)

W RATINGS - CLASS 1 (SEE ITEMS 3, 4, AND 4A)

C R

CLASSIFIED BY

UNDERWRITERS

LABORATORIES, INC.

TO UL 1479 AND CAN/ULC-

S115

US SYSTEM NO. F-A-2054

F RATING - 3 HR

T RATING - 0 AND 3 HR (SEE ITEM 3)

L RATING AT AMBIENT - LESS THAN 1 CFM/SQ FT (SEE ITEM 3)

L RATING AT 400 F - LESS THAN 1 CFM/SQ FT (SEE ITEM 3)

W RATINGS - CLASS 1 (SEE ITEMS 3, 4, AND 4A)

1. FLOOR ASSEMBLY — MIN 4-1/2 IN. (114 MM) THICK REINFORCED LIGHTWEIGHT OR NORMAL WEIGHT (100-150 PCF OR 1600-2400

KG/M3) CONCRETE.

1A. FLOOR ASSEMBLY - (OPTIONAL - NOT SHOWN) — THE FIRE RATED UNPROTECTED CONCRETE AND STEEL FLOOR ASSEMBLY SHALL BE CONSTRUCTED OF THE MATERIALS AND IN THE MANNER SPECIFIED IN THE INDIVIDUAL D900 SERIES DESIGNS IN THE UL

FIRE RESISTANCE DIRECTORY AND AS SUMMARIZED BELOW:

A. CONCRETE — MIN 4-1/2 IN (114 MM) THICK REINFORCED LIGHTWEIGHT OR NORMAL WEIGHT (100-150 PCF OR 1600-2400

KG/M3) CONCRETE.

B. STEEL FLOOR AND FORM UNITS* — COMPOSITE OR NON-COMPOSITE MAX 3 IN. (76 MM) DEEP GALV STEEL FLUTED

UNITS AS SPECIFIED IN THE INDIVIDUAL FLOOR-CEILING DESIGN.

2. FIRESTOP DEVICE* — CAST IN PLACE FIRESTOP DEVICE PERMANENTLY EMBEDDED DURING CONCRETE PLACEMENT OR GROUTED IN CONCRETE ASSEMBLY IN ACCORDANCE WITH ACCOMPANYING INSTALLATION INSTRUCTIONS. THE DEVICES MAY

EXTEND A MAX 2 IN. (51 MM) ABOVE THE TOP SURFACE OF THE CONCRETE.

3. THROUGH PENETRANTS — ONE NONMETALLIC PIPE OR CONDUIT TO BE INSTALLED WITHIN THE FIRESTOP SYSTEM. PIPE OR CONDUIT TO BE RIGIDLY SUPPORTED ON BOTH SIDES OF FLOOR ASSEMBLY. FOR W RATING WITH WATER BARRIER MODULE, PIPE SHALL BE INSTALLED FROM BOTTOM OF DEVICE. THE FOLLOWING TYPES AND SIZES OF NONMETALLIC PIPES OR CONDUITS MAY

BE USED:

A. POLYVINYL CHLORIDE (PVC) PIPE — NOM 6 IN. (152 MM) DIAM (OR SMALLER) SCHEDULE 40 SOLID OR CELLULAR CORE PVC PIPE FOR USE IN CLOSED (PROCESS OR SUPPLY) OR VENTED (DRAIN, WASTE OR VENT) PIPING SYSTEMS.

B. CHLORINATED POLYVINYL CHLORIDE (CPVC) PIPE — PIPE-NOM 6 IN. (152 MM) DIAM (OR SMALLER) SDR11 OR SDR13.5

CPVC PIPE FOR USE IN CLOSED (PROCESS OR SUPPLY) PIPING SYSTEMS.

C. RIGID NONMETALLIC CONDUIT+ — NOM 6 IN. (152 MM) DIAM (OR SMALLER) SCHEDULE 40 PVC CONDUIT INSTALLED IN

ACCORDANCE WITH THE NATIONAL ELECTRICAL CODE (NFPA NO. 70).

THE FIRESTOP DEVICES AND NONMETALLIC PENETRANTS SHALL BE SIZED AS FOLLOWS:

+3 HR T RATING APPLIES WHEN CP 680-P 3" AND CP 680-P 4" DEVICES ARE USED. 3 HR T RATING ALSO APPLIED WHEN CP 680-110/4"N DEVICE IS USED PROVIDED THAT MIN 4 IN. (102 MM) THICKNESS OF NOM 4 PCF (64 KG.M3) MINERAL WOOL BATT INSULATION TIGHTLY PACKED WITHIN ANNULUS BETWEEN PIPE AND WALL OF CP 680-110/4"N DEVICE. ++ L RATING APPLIES ONLY TO CP 680-P DEVICES AND ONLY WHEN THE NOM DIAM OF PIPE EQUALS SIZE OF DEVICE (2 IN. DIAM PIPE IN 2" DEVICE ETC.) L

RATING DOES NOT APPLY TO CP 680N DEVICES.

4. FIRESTOP DEVICE — TOP SEAL PLUG FOR USE WITH CP 680-P 2" DEVICE INSTALLED IN ACCORDANCE WITH THE MANUFACTURER'S INSTRUCTIONS. THE TOP SEAL PLUG IS OPTIONAL FOR NOM 1-1/2 IN. (38 MM) PIPES AND CONDUITS. TOP SEAL PLUGS ARE REQUIRED FOR ALL PIPES AND CONDUITS LESS THAN NOM 1-1/2 IN. (38 MM). W RATING APPLIES ONLY TO THE IPS TOP SEAL PLUG AND NOM 2 IN. DIAM PENETRANTS AND CPS TOP SEAL PLUG FOR NOM ½ TO 2 IN. (13 TO 51 MM) DIAM

PENETRANTS.

4A. FIRESTOP DEVICE* - WATER BARRIER MODULE — (OPTIONAL, NOT SHOWN) - ALTERNATE TO TOP SEAL PLUG (ITEM 4). APPLIES TO NOM 2", 3", 4" AND 6" WATER BARRIER MODULES USED IN COMBINATION WITH THE CP 680-P 2", CP 680-P 3", CP 680-P 4" AND CP 680-P 6" DEVICES, RESPECTIVELY, AND SUPPLIED BY DEVICE MANUFACTURER. MODULE IS THREADED ONTO TOP OF DEVICE. W RATING APPLIES ONLY WHEN WATER BARRIER MODULE IS USED AND NOM DIAM OF PENETRANT EQUALS SIZE OF DEVICE.

*BEARING THE UL CLASSIFICATION MARK

+BEARING THE UL LISTING MARK

NOM PIPE DIAMETER FIRESTOP DEVICE T RATING - HR

1/2 IN. TO 2 IN.

(19 MM TO 51 MM)

3 IN. (76 MM)

4 IN. (102 MM)

6 IN. (152 MM)

CP 680-75/2.5"N

CP 680-P 2"

CP 680-110-P 4"

CP 680-110/4"N

CP 680-P 3", CP 680-P 4"

CP 680-P 4"

CP 680-160/6"N

CP 680-P 6"

0 AND 3+

SINGLE NON-METALLIC PIPE OR CONDUIT

A A

SECTION A-A

C R

CLASSIFIED BY

UNDERWRITERS

LABORATORIES, INC.

TO UL 1479 AND CAN/ULC-

S115

US C

R

CLASSIFIED BY

UNDERWRITERS

LABORATORIES, INC.

TO UL 1479 AND CAN/ULC-

S115

US

C R

CLASSIFIED BY

UNDERWRITERS

LABORATORIES, INC.

TO UL 1479 AND CAN/ULC-

S115

US

C R

CLASSIFIED BY

UNDERWRITERS

LABORATORIES, INC.

TO UL 1479 AND CAN/ULC-

S115

US

CIRCULAR BLANK OPENINGS SINGLE NON-METALLIC PIPE OR CONDUITSINGLE INSULATED PIPES

SINGLE INSULATED PIPES

SYSTEM NO. C-BJ-2016

F RATING - 4 HR

T RATING - 2 HR

SYSTEM NO. C-BJ-5006

F RATING - 4 HR

T RATING - 1/2 HR

SYSTEM NO. C-BJ-1034

F RATING - 4 HR

T RATING - 0 HR

1. FLOOR OR WALL ASSEMBLY — MIN 5-1/2 IN. THICK REINFORCED LIGHTWEIGHT OR NORMAL WEIGHT (100-150 PCF) CONCRETE FLOOR OR MIN 6 IN. THICK REINFORCED LIGHTWEIGHT OR NORMAL WEIGHT CONCRETE WALL. WALL MAY ALSO BE CONSTRUCTED OF ANY UL CLASSIFIED CONCRETE BLOCKS*. MAX DIAM OF OPENING IS 10-1/2 IN.SEE CONCRETE BLOCKS (CAZT) CATEGORY IN FIRE RESISTANCE DIRECTORY FOR NAMES

OF MANUFACTURERS.

2. THROUGH-PENETRANTS — ONE METALLIC PIPE, CONDUIT OR TUBING TO BE INSTALLED EITHER CONCENTRICALLY OR ECCENTRICALLY WITHIN THE FIRESTOP SYSTEM. AN ANNULAR SPACE BETWEEN PIPE, CONDUIT OR TUBING AND PERIPHERY OF OPENING SHALL BE MIN 3/4 IN. TO MAX 3 IN. PIPE, CONDUIT OR TUBING TO BE RIGIDLY SUPPORTED ON BOTH SIDES OF FLOOR OR WALL ASSEMBLY. THE FOLLOWING TYPES AND

SIZES OF METALLIC PIPES, CONDUITS OR TUBING MAY BE USED:

A. STEEL PIPE — NOM 4 IN. DIAM (OR SMALLER) SCHEDULE 10 (OR HEAVIER) STEEL PIPE.

B. CONDUIT — NOM 4 IN. DIAM (OR SMALLER) STEEL ELECTRICAL METALLIC TUBING OR STEEL CONDUIT.

3. PACKING MATERIAL — MIN 4 IN. THICKNESS OF MIN 4.0 PCF MINERAL WOOL BATT INSULATION FIRMLY PACKED INTO OPENING AS A PERMANENT FORM. PACKING MATERIAL TO BE RECESSED FROM TOP SURFACE OF FLOOR OR FROM BOTH SURFACES OF WALL AS REQUIRED TO ACCOMMODATE THE REQUIRED THICKNESS

OF FILL MATERIAL.

4. FILL, VOID OR CAVITY MATERIAL* — CAULK — MIN 1 IN. THICKNESS OF FILL MATERIAL APPLIED WITHIN THE ANNULUS, FLUSH WITH TOP SURFACE OF FLOOR OR WITH BOTH SURFACES OF WALL. A MIN 1/2 IN. DIAM BEAD FILL MATERIAL TO BE INSTALLED AT INTERFACE OF PIPE, CONDUIT OR TUBING AND METAL COVER PLATE (ITEM

NO. 5) AND OVER BUTTED SEAMS OF METAL COVER PLATE.

5. METAL COVER PLATE — TWO PIECE COVER PLATE OF MIN 18 GAUGE STEEL WITH I.D. SAME AS O.D. OF PIPE, CONDUIT OR TUBING. O.D. OF COVER PLATE TO BE SIZED TO OVERLAP THE PERIPHERY OF OPENING A MIN 1-1/2 IN. INSTALLED AT TOP SURFACE OF FLOOR OR BOTH SIDES OF WALL. TWO PIECES TO BE BUTTED TOGETHER AROUND PERIMETER OF PIPE OR CONDUIT AND SECURED WITH 1/4 IN. DIAM BY MIN 1 IN. LONG STEEL EXPANSION BOLTS, OR EQUIVALENT, IN CONJUNCTION WITH STEEL NUTS AND WASHERS A MAX OF 1 IN.

FROM EACH SIDE OF EACH SEAM AND A MAX OF 4 IN. OC THROUGHOUT.

*BEARING THE UL CLASSIFICATION MARK

A

A SECTION A-A

SYSTEM NO. C-AJ-0055

ANSI/UL1479 (ASTM E814) CAN/ULC S115

F RATING - 3 HR

FT RATING - 0 HR

FH RATINGS - 3 HR

FTH RATING - 0HR

F RATING - 3 HR

T RATING - 0 HR

1. FLOOR OR WALL ASSEMBLY- MIN 4-112 IN. (114 MM) THICK REINFORCED LIGHTWEIGHT OR

NORMAL WEIGHT (100-150 PEL) CONCRETE. WALL MAY ALSO BE CONSTRUCTED OF ANY UL

CLASSIFIED CONCRETE BLOCKS'. MAX DIAM OF OPENING IS 4 IN. (102 MM).

SEE CONCRETE BLOCKS (CAZT) CATEGORY IN THE FIRE RESISTANCE DIRECTORY FOR NAMES

OF MANUFACTURERS.

2. METALLIC SLEEVE- NOM 4 IN. (102 MM) DIAM (OR SMALLER) SCHEDULE 40 (OR HEAVIER) STEEL

PIPE CAST OR GROUTED INTO FLOOR OR WALL ASSEMBLY, FLUSH WITH

FLOOR OR WALL SURFACES. SLEEVE MAY EXTEND MAX 3 IN. (76 MM) ABOVE TOP SURFACE OF

FLOOR.

3. FILL, VOID OR CAVITY MATENAL'- FIRE BLOCK MIN 2 IN. (51 MM) THICK CUT TO A DIAM 1/2 IN. (13

MM) LARGER THAN THE OPENING, FLUSH WITH BOTTOM SURFACE

OF FLOOR OR WITH BOTH SURFACES OF WALL.

*BEARING THE UL CLASSIFICATION MARK

A

A

SECTION A-A

1. FLOOR OR WALL ASSEMBLY -- MIN 6 IN. THICK REINFORCED LIGHTWEIGHT OR NORMAL WEIGHT (100-150 PCF) CONCRETE. WALL MAY ALSO BE CONSTRUCTED OF ANY UL CLASSIFIED CONCRETE BLOCKS*. MAX

DIAMETER OF OPENING IS 3 IN.

SEE CONCRETE BLOCKS (CAZT) CATEGORY IN THE FIRE RESISTANCE DIRECTORY FOR NAMES OF

MANUFACTURERS

2. STEEL SLEEVE -- NOM 3 IN. DIAM SCHEDULE 40 (OR SMALLER) STEEL PIPE CAST OR GROUTED INTO

FLOOR OR WALL ASSEMBLY, FLUSH WITH FLOOR OR WALL SURFACES.

3. POLYVINYLIDENE FLUORIDE PVDF PIPE -- NOM 2 IN. DIAM (OR SMALLER) SCHEDULE 40 PVDF FOR USE IN CLOSED (PROCESS OR SUPPLY) OR VENTED (DRAIN, WASTE OR VENT) PIPING SYSTEMS. ANNULAR SPACE BETWEEN PIPE AND SLEEVE TO BE MIN 0 IN. (POINT CONTACT) AND MAX 5/8 IN. PIPE TO BE RIGIDLY

SUPPORTED ON BOTH SIDES OF FLOOR OR WALL ASSEMBLY.

4. FIRESTOP SYSTEM -- THE FIRESTOP SYSTEM SHALL CONSIST OF THE FOLLOWING:

A. FILL, VOID OR CAVITY MATERIALS*-SEALANT -- MIN 1/2 IN. THICKNESS OF FILL MATERIAL APPLIED

WITHIN THE ANNULUS, FLUSH WITH BOTTOM SURFACE OF FLOOR OR BOTH SURFACES OF WALL.

B. FILL, VOID OR CAVITY MATERIAL* -- WRAP STRIP -- NOM 1/4 IN. THICK BY 2 IN. WIDE INTUMESCENT WRAP STRIP. TWO LAYERS OF WRAP STRIP ARE CONTINUOUSLY WRAPPED AROUND THE PIPE AND HELD IN PLACE WITH TAPE. WRAP STRIP BUTTED TIGHTLY AGAINST BOTTOM SURFACE OF FLOOR OR BOTH

SURFACES OF WALL.

C. STEEL COLLAR -- COLLAR FABRICATED FROM COILS OF PRECUT MIN 0.017 IN. THICK (NO. 28 MSG) GALV STEEL AVAILABLE FROM THE SEALANT MANUFACTURER. COLLAR SHALL BE NOM 1-3/4 IN. DEEP WITH 1 IN. WIDE BY 2 IN. LONG ANCHORS TABS ON 2 IN. CENTERS FOR SECUREMENT TO FLOOR OR WALL ASSEMBLY. THE ANCHOR TABS SHALL BE BENT 90 DEGREE OUTWARD FOR SECUREMENT TO THE FLOOR OR WALL ASSEMBLY. THE OPPOSITE SIDE INCORPORATES RETAINER TABS, 1/2 IN. WIDE BY 3/16 IN. LONG, PREBENT TOWARD THE PIPE SURFACE. COLLAR SHALL BE TIGHTLY WRAPPED OVER THE WRAP STRIP, OVERLAPPING MIN. 1 IN AT SEAM. A NOM 1/2 IN. WIDE STAINLESS STEEL HOSE CLAMP SHALL BE SECURED TO THE COLLAR AT ITS MID-HEIGHT. EVERY OTHER ANCHOR TAB OF COLLAR SECURED TO CONCRETE SLAB WITH 1/4 IN. DIAM BY 1-3/4 IN. LONG STEEL EXPANSION TYPE MASONRY FASTENERS, 1-1/2 IN LONG CONCRETE SCREW ANCHORS OR 0.145 IN. DIAM BY 1-1/4 IN. LONG POWDER ACTUATED FASTENERS UTILIZING A 1-7/16 DIAM BY 1/16 IN. THICK STEEL WASHER. IN FLOOR ASSEMBLIES, ONE COLLAR TO BE USED AT THE BOTTOM OF THE CONCRETE FLOOR ONLY. IN WALL ASSEMBLIES, A COLLAR IS

USED ON BOTH SURFACES.

*BEARING THE UL CLASSIFICATION MARK

4A

4B 4C

1 2

1. FLOOR OR WALL ASSEMBLY — MIN 5-1/2 IN. THICK REINFORCED LIGHTWEIGHT OR NORMAL WEIGHT (100-150 PCF) CONCRETE FLOOR OR MIN 6 IN. THICK REINFORCED LIGHTWEIGHT OR NORMAL WEIGHT CONCRETE WALL.

WALL MAY ALSO BE CONSTRUCTED OF ANY UL CLASSIFIED CONCRETE BLOCKS*. MAX DIAM OF OPENING IS 29 IN.

SEE CONCRETE BLOCKS (CAZT) CATEGORY IN FIRE RESISTANCE DIRECTORY FOR NAMES OF

MANUFACTURERS.

2. THROUGH-PENETRANTS — ONE METALLIC PIPE TO BE INSTALLED EITHER CONCENTRICALLY OR ECCENTRICALLY WITHIN THE FIRESTOP SYSTEM. PIPE TO BE RIGIDLY SUPPORTED ON BOTH SIDES OF FLOOR OR

WALL ASSEMBLY. THE FOLLOWING TYPES AND SIZES OF METALLIC PIPES MAY BE USED:

A. STEEL PIPE — NOM 20 IN. DIAM (OR SMALLER) SCHEDULE 10 (OR HEAVIER) STEEL PIPE.

3. PIPE COVERING — MAX 3 IN. THICK HOLLOW CYLINDRICAL HEAVY DENSITY (MIN 3.5 PCF) GLASS FIBER UNITS JACKETED ON THE OUTSIDE WITH AN ALL SERVICE JACKET. LONGITUDINAL JOINTS SEALED WITH METAL FASTENERS OR FACTORY-APPLIED SELF-SEALING LAP TAPE.TRANSVERSE JOINTS SECURED WITH METAL FASTENERS OR WITH BUTT TAPE SUPPLIED WITH THE PRODUCT. PIPE COVERING TO TERMINATE MIN 6 IN. FROM EACH SIDE OF FLOOR OR WALL ASSEMBLY. SEE PIPE AND EQUIPMENT COVERING — MATERIALS (BRGU) CATEGORY IN THE BUILDING MATERIALS DIRECTORY FOR NAMES OF MANUFACTURERS. ANY PIPE COVERING MATERIAL MEETING THE ABOVE SPECIFICATIONS AND BEARING THE UL CLASSIFICATION MARKING WITH A FLAME SPREAD INDEX OF 25 OR LESS AND A SMOKE DEVELOPED INDEX OF 50 OR LESS MAY BE USED.

4. FIRESTOP SYSTEM — THE FIRESTOP SYSTEM SHALL CONSIST OF THE FOLLOWING:

A. PIPE COVERING* — MAX 3 IN. THICK HOLLOW CYLINDRICAL HEAVY DENSITY (MIN 5.2 PCF) UNFACED MINERAL WOOL UNITS EXTENDING MIN 6 IN. BEYOND EACH SURFACE OF THE FLOOR OR WALL. PIPE COVERING SECURED WITH NO. 18 GAUGE TIE WIRE 3 IN. BEYOND EACH SURFACE OF THE CONCRETE SLAB. THE ANNULAR SPACE SHALL BE MIN 1 IN. TO MAX 2-1/4 IN. SEE PIPE AND EQUIPMENT COVERING — MATERIALS (BRGU) CATEGORY IN THE BUILDING MATERIALS DIRECTORY FOR NAMES OF MANUFACTURERS. ANY PIPE COVERING MATERIAL MEETING THE ABOVE SPECIFICATIONS AND BEARING THE UL CLASSIFICATION MARKING WITH A FLAME SPREAD INDEX OF 25 OR LESS AND A SMOKE DEVELOPED INDEX OF 50 OR LESS MAY BE USED.

B. SHEATHING MATERIAL* — ALL SERVICE JACKET MATERIAL SHALL BE WRAPPED AROUND THE OUTER CIRCUMFERENCE OF THE PIPE COVERING MATERIAL (ITEM 4A) WITH KRAFT FACING EXPOSED. LONGITUDINAL JOINTS SEALED WITH METAL FASTENERS. SEE SHEATHING MATERIAL (BVDV) CATEGORY IN THE BUILDING MATERIALS DIRECTORY FOR NAMES OF MANUFACTURERS. ANY SHEATHING MATERIAL MEETING THE ABOVE SPECIFICATIONS AND BEARING THE UL CLASSIFICATION MARKING WITH A FLAME SPREAD INDEX OF 25 OR LESS

AND A SMOKE DEVELOPED INDEX OF 50 OR LESS MAY BE USED.

C. PACKING MATERIAL — MIN 4 IN. THICKNESS OF MIN 4.0 PCF MINERAL WOOL BATT INSULATION FIRMLY PACKED INTO OPENING AS A PERMANENT FORM. PACKING MATERIAL TO BE RECESSED FROM TOP SURFACE OF FLOOR OR FROM BOTH SURFACES OF WALL AS REQUIRED TO ACCOMMODATE THE REQUIRED THICKNESS OF

FILL MATERIAL.

D. FILL, VOID OR CAVITY MATERIAL* — CAULK — MIN 1 IN. THICKNESS OF FILL MATERIAL APPLIED WITHIN THE ANNULUS, FLUSH WITH TOP SURFACE OF FLOOR OR WITH BOTH SURFACES OF WALL. A MIN 1/2 IN. DIAM BEAD FILL MATERIAL TO BE INSTALLED AT INTERFACE OF PIPE COVERING AND METAL COVER PLATE (ITEM NO.

4E) AND OVER BUTTED SEAMS OF METAL COVER PLATE.

E. METAL COVER PLATE — TWO PIECE COVER PLATE OF MIN 18 GAUGE STEEL WITH I.D. SAME AS O.D. OF PIPE, CONDUIT OR TUBING. O.D. OF COVER PLATE TO BE SIZED TO OVERLAP THE PERIPHERY OF OPENING A MIN 1-1/2 IN. INSTALLED AT TOP SURFACE OF FLOOR OR BOTH SIDES OF WALL. TWO PIECES TO BE BUTTED TOGETHER AROUND PERIMETER OF PIPE, PENETRATING THE SHEATHING MATERIAL AND PIPE COVERING (ITEM NOS. 4B AND 4A) TO FULLY CONTACT THE PIPE. SECURED WITH 1/4 IN. DIAM BY MIN 1 IN. LONG STEEL EXPANSION BOLTS, OR EQUIVALENT, IN CONJUNCTION WITH STEEL NUTS AND WASHERS A MAX OF 1 IN. FROM EACH SIDE OF

EACH SEAM AND A MAX OF 4 IN. OC THROUGHOUT.

*BEARING THE UL CLASSIFICATION MARK

A

A

SECTION A-A

4E 4D

4C

4D

4A

4B

SINGLE NON-METALLIC PIPE OR CONDUIT

1. WALL ASSEMBLY — MIN 7-1/2 IN. THICK REINFORCED LIGHTWEIGHT OR NORMAL WEIGHT (100-150 PCF) CONCRETE. WALL MAY ALSO BE CONSTRUCTED OF ANYUL CLASSIFIED CONCRETE BLOCKS*. MAX DIAM OF OPENING IS 4 IN. SEE CONCRETE BLOCKS (CAZT) CATEGORY IN THE FIRE RESISTANCE DIRECTORY

FOR NAMES OF MANUFACTURERS.

2. STEEL SLEEVE — NOM 4 IN. DIAM (OR SMALLER) SCHEDULE 40 (OR HEAVIER) STEEL PIPE SLEEVE FRICTION FIT IN NOM 4 IN. DIAM CIRCULAR OPENING CORE DRILLED THROUGH WALL. LENGTH OF STEEL

SLEEVE TO BE EQUAL TO THICKNESS OF WALL.

3. THROUGH PENETRANTS — ONE NONMETALLIC PIPE TO BE INSTALLED EITHER CONCENTRICALLY OR ECCENTRICALLY WITHIN THE FIRESTOP SYSTEM. THE ANNULAR SPACE BETWEEN PIPE AND THE STEEL SLEEVE SHALL BE MIN 1/2 IN. TO A MAX 1 IN. THE FOLLOWING TYPES AND SIZES OF NONMETALLIC PIPES

MAY BE USED:

A. POLYVINYL CHLORIDE (PVC) PIPE — NOM 2 IN. DIAM (OR SMALLER) CELLULAR OR SOLID CORE SCHEDULE 40 (OR HEAVIER) PIPE FOR USE IN CLOSED (PROCESS OR SUPPLY) PIPING SYSTEMS.

B. CHLORINATED POLYVINYL CHLORIDE (CPVC) PIPE — NOM 2 IN. DIAM (OR SMALLER) SDR 17 CPVC

PIPE FOR USE IN CLOSED (PROCESS OR SUPPLY) PIPING SYSTEMS.

4. FILL, VOID OR CAVITY MATERIAL*—SEALANT — MIN 2 IN. THICKNESS OF FILL MATERIAL APPLIED WITHIN

ANNULUS, FLUSH WITH BOTH SURFACES OF WALL.

*BEARING THE UL CLASSIFICATION MARK

SINGLE NON-METALLIC PIPE OR CONDUIT

SYSTEM NO. W-J-2057

F RATING - 4 HR

T RATING - 2 HR

C R

CLASSIFIED BY

UNDERWRITERS

LABORATORIES, INC.

TO UL 1479 AND CAN/ULC-

S115

US

A

A

SECTION A-A

SINGLE INSULATED PIPES

NOM PIPE DIAM, IN.

(MM)

NOM THICK. OF PIPE

INSUL., IN. (MM)

FIRESTOP DEVICE T-

RATING,

HR

1/2 (13)

1 (25)

2 (51)

2 (51)

4 (102)

1 (25)

1 (25) (SEE ITEM 5)

1 (25)

3/4 (19)

1 (25)

1 (25)

1 (25)

3/4(19)

3/4(19)

CP 680-75/2.5"N, CP 682-72/2.5"CP

680-M 2", CP 680-P 2"

CP 680-75/2.5"N CP 680-P 3"

CP 680-M 3", CP 680-P 3"

CP 682-110/4"CP 680-M 4"

CP 680 110/4"N, CP682 110/4"CP

680-M 4", CP 680-P 4"

CP 680-100/4"NCP 680-P 4"

CP 680-160/6"NCP 680-P 6

3/4

1/2

1/2

1/2

1/2

1/2

1/2

TUBE INSULATION - PLASTICS+ - NOM 3/4 OR 1 IN. (19 OR 25 MM) THICK ACRYONITRILE

BUTADIENE/POLYVINYL CHLORIDE (AB/PVC) FLEXIBLE FOAM FURNISHED IN THE FORM OF

TUBING. SEE PLASTICS+ (QMFZ2) CATEGORY IN THE PLASTICS RECOGNIZED COMPONENT

DIRECTORY FOR NAMES OF MANUFACTURERS. ANY RECOGNIZED COMPONENT TUBE

INSULATION MATERIAL MEETING THE ABOVE SPECIFICATIONS AND HAVING A UL94

FLAMMABILITY CLASSIFICATION OF 94-5VA MAY BE USED.

PACKING MATERIAL - (NOT SHOWN) - WHEN USING A 1 IN. (25 MM) DIAM PIPE WITH 1 IN. (25 MM) AB/PVC PIPE INSULATION IN A 4 IN. (102 MM) DEVICE, AND A MIN 2 IN. (51 MM) THICKNESS OF MIN

4 PCF (64 KG/M³) MINERAL WOOL BATT INSULATION SHALL BE FIRMLY PACKED INTO TOP OF

DEVICES, FLUSH WITH THE TOP OF THE DEVICE.

*BEARING THE UL CLASSIFICATION MARK

4.

5.

THE FIRESTOP DEVICE AND METALLIC PENETRANT SHALL BE SIZED AS FOLLOWS:

FLOOR OR WALL ASSEMBLY - MIN 2-1/2 IN. (64 MM) THICK REINFORCED LIGHTWEIGHT OR

NORMAL WEIGHT (100-150 PCF OR 1600-2400 KG/M³) CONCRETE.

FLOOR ASSEMBLY - (OPTIONAL - NOT SHOWN) - THE FIRE RATED UNPROTECTED CONCRETE

AND STEEL FLOOR ASSEMBLY SHALL BE CONSTRUCTED OF THE MATERIALS AND IN TEH

MANNER SPECIFIED IN TEH INDIVIDUAL D900 SERIES DESIGNS IN THE FIRE RESISTANCE

DIRECTORY AND AS SUMMARIZED BELOW:

1.

1A.

2.

3.

A. STEEL FLOOR AND FORM UNITS* - COMPOSITE OR NON-COMPOSITE MAX

2 IN. (76 MM) DEEP GALV STEEL FLUTED UNITS AS SPECIFIED IN THE

INDIVIDUAL FLOOR-CEILING DESIGN.

B. CONCRETE - MIN 2-1/2 IN. (64 MM) THICK REINFORCED LIGHTWEIGHT OR

NORMAL WEIGHT (100-150 PCF OR 1600-2400 KG/M³) CONCRETE.

FIRESTOP DEVICE* - CAST IN PLACE FIRESTOP DEVICE PERMANENTLY EMBEDDED DURING

CONCRETE PLACEMENT OR GROUTED IN CONCRETE FLOOR ASSEMBLY IN ACCORDANCE WITH

ACCOMPANYING INSTALLATION INSTRUCTIONS WITH A MAX 2 IN. (51 MM) PROJECTION ABOVE

THE TOP SURFACE OF THE CONCRETE.

THROUGH PENERANTS - ONE METALLIC PIPE, CONDUIT OR TUBING TO BE INSTALLED WITHIN

THE FIRESTOP DEVICE. PIPE, CONDUIT, OR TUBING TO BE RIGIDLY SUPPORTED ON BOTH SIDES

OF FLOOR ASSEMBLY. THE FOLLOWING TYPES OF PIPE, CONDUIT OR TUBING MAY BE USED:

A. STEEL PIPE - NOM. 4 IN. (102 MM) DIAM (OR SMALLER) SCHEDULE 10 (OR

HEAVIER) STEEL PIPE.

B. COPPER TUBING - NOM 4 IN. (102 MM) DIAM (OR SMALLER) TYPE L (OR

HEAVIER) COPPER TUBING.

C. COPPER PIPE. - NOM 4 IN. (102 MM) DIAM (OR SMALLER) REGULAR (OR

HEAVIER) COPPER PIPE.

SYSTEM NO. F-A-5015

F RATING - 2 HR

T RATING - 1/2 HR AND 3/4 HR (SEE ITEM 3)

C R

CLASSIFIED BY

UNDERWRITERS

LABORATORIES, INC.

TO UL 1479 AND CAN/ULC-

S115

US

SECTION A-A

A A

P R

ELI

M

IN

AR

Y

N O

T F O

R

C O

N S

TR

U C

TIO

N

C B

LH

D E

SIG

N

IN

C

VA FORM 08 - 6231

F

E

D

C

B

A

987654321 10

F

E

D

C

B

A

987654321 10

BID AND CONSTRUCTION

Project Number

Building Number

Drawing Number

VA Building 330

Project Title

Location

Issued Date Checked Drawn

Drawing Title

Approved: Project Director

Phase

FULLY SPRINKLERED

Office of Construction and Facilities Management

STAMPARCHITECT / ENGINEER OF RECORD

7850 Freeway Circle

440.243.2000 t

Cleveland, OH 44130

440.243.3305 f

CONSULTANT

SCHEESER BUCKLEY MAYFIELD

1540 CORPORATE WOODS PARKWAY

UNIONTOWN, OHIO 44685

MECHANICAL ENGINEER

ELECTRICAL ENGINEER

/6 /2

:1

:4

P

M C

R e v it L o c a l\

M e n ta l H e a lt h F lo o r

C e n tr a l_

R

C e n tr a l_ rb o u k z a m

.r v t

GI-103

552-20-101

MS CE

VA DAYTON RENOVATE MENTAL

HEALTH 6TH FLOOR

09/20/2021

4100 WEST THIRD STREET, DAYTON, OHIO 45428

PENETRATION FIRE STOPPING DETAILS

SYSTEM NO. C-AJ-1226

F RATING - 3 HR

T RATING - 0 HR

L RATING AT AMBIENT - LESS THAN 1 CFM/SQ FT

L RATING AT 400 F - 4 CFM/SQFT

SYSTEM NO. C-AJ-3180

F RATING - 3 HR

T RATING - 0 HR

SYSTEM NO. C-AJ-7051

F RATING - 3 HR

T RATING - 1 HR

SINGLE METAL PIPES OR CONDUIT SINGLE OR BUNDLED CABLES

NON-INSULATED MECHANICAL DUCTWORK

WITHOUT DAMPERS

C R

CLASSIFIED BY

UNDERWRITERS

LABORATORIES, INC.

TO UL 1479 AND CAN/ULC-

S115

US C

R

CLASSIFIED BY

UNDERWRITERS

LABORATORIES, INC.

TO UL 1479 AND CAN/ULC-

S115

US

C R

CLASSIFIED BY

UNDERWRITERS

LABORATORIES, INC.

TO UL 1479 AND CAN/ULC-

S115

US

A

A

SECTION A-A

4B

4B 1

4A

SECTION A-A

A

A

A

A SECTION A-A

3B

3A

*BEARING THE UL CLASSIFICATION MARK

FLOOR OR WALL ASSEMBLY - MIN 4-1/2 IN. THICK REINFORCED LIGHTWEIGHT OR NORMAL

WEIGHT (100-150 PCF) CONCRETE. WALL MAY ALSO BE CONSTRUCTED OF ANY UL CLASSIFIED

CONCRETE BLOCKS*. MAX DIAM OF OPENING IS 32 IN.

METALLIC SLEEVE - (OPTIONAL) NOM 32 IN. DIAM (OR SMALLER) SCHEDULE 40 (OR HEAVIER)

STEEL SLEEVE CST OR GROUTED INTO FLOOR OR WALL ASSEMBLY, FLUSH WITH FLOOR OR

WALL SURFACES OR EXTENDING A MAX OF 3 IN. ABOVE FLOOR OR BEYONE BOTH SURFACES

OF WALL.

SHEET METAL SLEEVE - (OPTIONAL) MAX 6 IN. DIAM, MIN 26 GA GALV STEEL PROVIDED WITH A 26

GA GALV STEEL SQURE FLANGE SPOT WELDED TO THE SLEEVE AT A APPROX MID-HEIGHT, OR

FLUSH WITH BOTTOM OF SLEEVE IN FLOORS, AND SIZED TO BE A MIN OF 2 IN. LARGER THAN

THE SLEEVE DIAM. THE SLEEVE IS TO BE CAST IN PLACE AND MAY EXTEND A MAX OF 4 IN.

BELOW THE BOTTOM OF THE DECK AND A MAX OF 1 IN. ABOVE THE TOP SURFACE OF THE

CONCRETE FLOOR.

THROUGH-PENETRANT - ONE METALLIC PIPE, TUBE OR CONDUIT TO BE INSTALLED EITHER

CONCENTRICALLY OR ECCENTRICALLY WITHIN THE FIRESTOP SYSTEM. THE ANNULAR SPACE

BETWEEN PENETRANT AND PERIPHERY OF OPENING SHALL BE MIN 0 IN. (POINT CONTACT) TO

MAX 1-7/8 IN. SUPPORTED ON BOTH SIDES OF FLOOR OR WALL ASSEMBLY. THE FOLLOWING

TYPES AND SIZES OF METALLIC PENETRANTS MAY BE USED:

1.

2.

3.

4.

5.

A. STEEL PIPE - NOM 30 IN. DIAM (OR SMALLER) SCHEDULE 10 (OR HEAVIER)

STEEL PIPE.

B. IRON PIPE - NOM 30 IN. DIAM (OR SMALLER) CAST OR DUCTILE IRON PIPE.

C. COPPER PIPE - NOM 6 IN. DIAM (OR SMALLER) REGULAR (OR HEAVIER)

COPPER PIPE.

D. COPPER TUBING - NOM 6 IN. DIAM (OR SMALLER) TYPE L (OR HEAVIER)

COPPER TUBING.

E. CONDUIT - NOM 6 IN. DIAM (OR SMALLER) STEEL CONDUIT.

F. CONDUIT - NOM 4 IN. DIAM (OR SMALLER) STEEL ELECTRICAL METALLIC

TUBING (EMT).

FIRESTOP SYSTEM - THE FIRESTOP SYSTEM SHALL CONSIST OF THE FOLLOWING:

A. PACKING MATERIAL - MIN 4 IN. THICKNESS OF MIN 4 PCF MINERAL WOOL

BATT INSULATION FIRMLY PACKED INTO OPENING AS A PERMANENT

FORM. PACKING METERIAL TO BE RECESSED FROM TOP SURFACE OF

FLOOR OR SLEEVE OR FROM BOTH SURFACES OF WALL OR SLEEVE AS

REQUIRED TO ACCOMMODATE THE REQUIRED THICKNESS OF FILL

MATERIAL.

B. FILL, VOID, OR CAVITY MATERIAL* - SEALANT - MIN 1/4 IN. THICKNESS OF

FILL MATERIAL APPLIED WITHIN THE ANNULUS, FLUSH WITH TOP

SURFACE OF FLOOR OR SLEEVE OR WITH BOTH SURFACES OF WALL OR

SLEEVE. AT THE POINT OR CONTINUOUS CONTACT LOCATIONS BEWEEN

PENETRANT AND CONCRETE OR SLEEVE, A MIN 1/4 IN. DIAM BEAD OF FILL

MATERIAL SHALL BE APPLIED AT THE CONCRETE OR SLEEVE/PIPE

PENETRANT INTERFACE ON THE TOP SURFACE OF FLOOR AND ON BOTH

SURFACES OF WALL.

FLOOR OR WALL ASSEMBLY - MIN 4-1/2 IN. (114 MM) THICK REINFORCED LIGHTWEIGHT OR

NORMAL WEIGHT (100-150 PCF OR 1600-2400 KG/M³) CONCRETE FLOOR OR MIN 4-3/4 IN. (152

MM). SEE CONCRETE BLOCKS*. MAX DIAM OF OPENING IS 6 IN. (152 MM). SEE CONCRETE

BLOCKS (CAZT) CATEGORY IN THE FIRE RESISTANCE DIRECTORY FOR NAMES OF

MANUFACTURERS.

STEEL SLEEVE - (OPTIONAL) - NOM 6 IN. (152 MM) DIAM (OR SMALLER) SCHEDULE 40 (OR

HEAVIER) STEEL PIPE CAST OR GROUTED INTO FLOOR OR WALL ASSEMBLY, FLUSH WITH

FLOOR OR WALLL SURFACES.

CABLES - AGGREGATE CROSS-SECTIONAL AREA OF CABLES IN OPENING TO BE MAX 45% OF

THE AGGREGATE CROSS-SECTIONAL AREA OF THE OPENING. CABLES TO BE RIGIDLY

SUPPORTED ON BOTH SIDES OF FLOOR OR WALL ASSEMBLY. ANY COMBINATION OF THE

FOLLOWING TYPES AND SIZES OF METALLIC CONDUCTOR OR FIBER OPTIC CABLE MAY BE

USED:

1.

2.

3.

4.

5.

A. MAX 500 KCMIL SINGLE COPPER CONNECTOR POWER CABLE WITH

THERMOPLASTIC INSULATION AND POLYVINYL CHLORIDE ( PVC) JACKET.

B. MAX 300 KCMIL SINGLE COPPER CONDUCTOR TELECOMMUNICATION

CABLES WITH POLYVINYL CHLORIDE (PVC) INSULATION AND JACKET

MATERIAL.

C. MAX 7/C COPPER CONDUTOR NO. 12 AWG MULTICONDUTOR POWER AND

CONTROL CABLES WITH POLYVNYL CHOLORIDE (PVC) OR CROSS-LINKED

POLYETHYLENE (XLPE) INSULATION AND PVC JACKET.

D. MULTIPLE FIBER OPTICAL COMMUNICATION CABLES JACKETED WITH PVC

AND HAVING A MAX OUTSIDE DIAM OF 1/2 IN. (13 MM).

E. MAX 3/C COPPER CONDUCTOR NO. 12 AWG WITH BARE ALUMINUM

GROUND, POLYVINYL CHOLRIDE (PVC) INSULATED STEEL, METAL-CLAD

CABLE.

F. MAX 3/C WITH GROUND 2/0 AWG COPPER CONDUCTOR SER CABLE WITH

CROSS-LINKED POLYETHYLENE (XLPE) INSULATION AND POLYVINYL

CHLORIDE (PVC) JACKET.

G. RG/U COAXIAL CABLE WITH POLYETHYLENE (PE) INSULATION AND

POLYVINYL CHLORIDE (PVC) JACKET HAVING A MAX OUTSIDE DIAMTER

OF 1/2 IN. (13 MM).

H. FIRE RESISTIVE CABLES* - MAX 1-1/4 IN. (32 MM) DIAM SINGLE

CONDUCTOR OR MULTI CONDUCTOR TYPE MI CABLE. A MIN1/8 IN. (3 MM)

SEPARATION SHALL BE MAINTAINED BETWEEN MI CABLES AND ANY

OTHER TYPES OF CABLE.

PACKING MATERIAL - MIN 4-1/4 IN. (108 MM) THICKNESS OF MIN 4 PCF (64 KG/M³) MINERAL WOOL

BATT INSULATION FIRMLY PACKED INTO OPENING AS A PERMANENT FORM. PACKING MATERIAL

TO BE RECESSED FROM TOP SURFACE OF FLOOR TO ACCOMMODATE THE REQUIRED

THICKNESS OF FILL METERIAL.

FILL, VOID, OR CAVITY MATERIAL* - SEALANT - MIN 1/4 IN. (6.4 MM) THICKNESS OF FILL MATERIAL

APPLIED WITHIN THE ANNULUS, FLUSH WITH TOP SURFACE OF FLOOR OR WITH BOTH

SURFACES OF WALL.

*BEARING THE UL CLASSIFICATION MARK

FLOOR OR WALL ASSEMBLY - MIN 4-1/2 IN. (114 MM) THICK REINFORCED LIGHTWEIGHT OR

NORMAL WEIGHT (100-150 PCF OR 1600-2400 KG/M³) CONCRETE. WALL MAY ALSO BE

CONSTRUCTED OF ANY UNDERWRITERS LABORATORIES INC.

CLASSIFIED CONCRETE BLOCKS*. MAX AREA OF OPENING IS 1024 IN. SQ. WITH A MAX

DIMENSION OF 32 IN. SEE CONCRETE BLOCKS (CAZT) CATEGORY IN THE FIRE RESISTANCE

DIRECTORY FOR NAMES OF MANUFACTURERS.

STEEL DUCT - NOM 30 BY 30 IN. (OR SMALLER) NO. 24 GAUGE (OR HEAVIER) GALV STEEL DUCT.

ONE STEEL DUCT TO BE POSITIONED WITHIN THE FIRESTIP SYSTEM. THE ANNULAR SPACE

SHALL BE MIN 1/4 IN. TO A MAX 1-3/4 IN. DUCT TO BE RIGIDLY SUPPORTED ON BOTH SIDES FO

FLOOR OR WALL ASSEMBLY.

FIRESTOP SYSTEM - THE FIRESTOP SYSTEM SHALL CONSIST OF THE FOLLOWING:

1.

2.

3.

4.

A. PACKING MATERIALS - MIN 3-1/2 IN. THICKNESS OF MIN 4 PCF MINERAL

WOOL BATT INSULATION FIRMLY PACKED INTO OPENING AS A

PERMANENT FORM BETWEEN TEH BARE STEEL DUCT AND THE

PERIPHERY OF THE OPENING. PACKING MATERIAL TO BE RECESSED

FROM TOP SURFACE OF FLOOR OR BOTH SURFACES OF WALL AS

REQUIRED TO ACCOMMODATE THE REQUIRED THICKNESS OF FILL

MATERIAL

B. FILL, VOID, OR CAVITY MATERIAL* - SEALANT - MIN 1 IN. THICKNESS OF

FILL MATERIAL APPLIED WITHIN ANNULUS, FLUSH WITH TOP SURFACE OF

FLOOR OR BOTH SURFACES OF WALL.

STEEL RETAINING ANGLE - NOM 2 IN. BY 2 IN. BY NO. 16 GUAGE (OR HEAVIER) STEEL ANGLES

ATTACHED TO ALL FOUR SIDES OF THE STEEL DUCT ON THE TOP SURFACE OR BOTH

SURFACES OF THE WALL. THE ANGLES SHALL BE ATTACHED WITH NO. 8 (OR LARGER) STEEL

SHEET METAL SCREWS SPACED MAX OF 1 IN. FROM EACH END AND A MAX OF 3 IN. O.C.

*BEARING THE UL CLASSIFICATION MARK

SYSTEM NO. W-J-8007

C R

CLASSIFIED BY

UNDERWRITERS

LABORATORIES, INC.

TO UL 1479 AND CAN/ULC-

S115

US

1. WALL ASSEMBLY — MIN 7-5/8 IN. (194 MM) THICK WALL ASSEMBLY CONSTRUCTED OF ANY UL CLASSIFIED CONCRETE BLOCKS*. MAX AREA OF OPENING IS 2496 IN. SQ. (161 M2) WITH MAX DIMENSION OF 52 IN. (1321 MM). SEE CONCRETE BLOCKS (CAZT) CATEGORY IN THE FIRE RESISTANCE

DIRECTORY FOR NAMES OF MANUFACTURERS.

2. CABLE TRAY* — MAX 36 IN. (914 MM) WIDE BY 6 IN. (152 MM) DEEP OPEN-LADDER CABLE TRAY WITH CHANNEL-SHAPED SIDE RAILS FORMED OF 0.067 IN. (1.7MM) THICK ALUMINUM AND WITH 1-1/2 IN. (38 MM) WIDE BY 3/4 IN. (19 MM) DEEP CHANNEL- SHAPED RUNGS SPACED 10 IN. (254 MM) OC.

ONE CABLE TRAY TO BE INSTALLED IN THE OPENING. THE ANNULAR SPACE BETWEEN ADJACENT PENETRATING ITEMS SHALL BE MIN 2 IN. (51 MM) TO MAX 4-1/2 IN. (114 MM). THE MAX ANNULAR SPACE BETWEEN THE PERIPHERY OF THE OPENING SHALL BE MIN 1 IN. (25 MM) TO MAX 3 IN. (76

MM). CABLE TRAY TO BE RIGIDLY SUPPORTED ON BOTH SIDES OF WALL ASSEMBLY.

3. CABLES — AGGREGATE CROSS-SECTIONAL AREA OF CABLES IN CABLE TRAY TO BE MAX 40

PERCENT OF THE CROSS-SECTIONAL AREA OF THE CABLE TRAY BASED ON A MAX 6 IN. (152 MM) CABLE LOADING DEPTH WITHIN THE CABLE TRAY. ANY COMBINATION OF THE FOLLOWING TYPES

AND SIZES OF CABLES MAY BE USED:

A. 300 PAIR — NO. 24 AWG TELEPHONE CABLE WITH POLYVINYL CHLORIDE (PVC) INSULATION

AND PVC JACKET.

B. 1/C - 500 KCMIL WITH THERMOPLASTIC INSULATION AND NYLON JACKET.

C. 24 FIBER OPTIC CABLE WITH POLYVINYL CHLORIDE (PVC) OUTER AND SUBUNIT JACKET.

D. 7/C NO. 12 AWG CABLE WITH POLYVINYL CHLORIDE (PVC) INSULATION AND PVC JACKET.

4. THROUGH PENETRANTS — ONE OR MORE PIPES OR TUBES TO BE INSTALLED WITHIN THE

OPENING. THE TOTAL NUMBER OF THROUGH-PENETRANTS IS DEPENDENT ON THE SIZE OF THE

OPENING AND TYPES AND SIZES OF THE PENETRANTS. ANY COMBINATION OF THE PENETRANTS

DESCRIBED BELOW MAY BE USED PROVIDED THAT THE FOLLOWING PARAMETERS RELATIVE TO THE

ANNULAR SPACES AND THE SPACINGS BETWEEN THE PIPES ARE MAINTAINED. THE SPACE

BETWEEN PIPES, CONDUITS OR TUBING SHALL BE MIN 1-1/2 IN.(38 MM) TO MAX 4-3/4 IN. (121 MM). THE SPACE BETWEEN THE PERIPHERY OF THE OPENING AND THE PIPES OR CONDUITS SHALL BE MIN 3 IN. (76 MM) TO MAX 4-1/4 IN. (108 MM). PIPE, CONDUIT OR TUBING TO BE RIGIDLY SUPPORTED ON BOTH SIDES OF THE WALL ASSEMBLY. THE FOLLOWING TYPES AND SIZES OF METALLIC PIPES, CONDUITS OR TUBING MAY BE USED:

A. STEEL PIPE — NOM 12 IN. (305 MM) DIAM (OR SMALLER) SCHEDULE 10 (OR HEAVIER) STEEL

PIPE.

B. IRON PIPE — NOM 12 IN. (305 MM) DIAM (OR SMALLER) CAST OR DUCTILE IRON PIPE.

C. CONDUIT — NOM 4 IN. (102 MM) DIAM (OR SMALLER) STEEL ELECTRIC METALLIC TUBING OR

6 IN. (152 MM) DIAM STEEL CONDUIT.

D. COPPER TUBING — NOM 6 IN. (152 MM) DIAM (OR SMALLER) TYPE L (OR HEAVIER) COPPER

TUBING.

E. COPPER PIPE — NOM 6 IN. (152 MM) DIAM (OR SMALLER) REGULAR (OR…