Attachment 0012_MEO B2939.pdf

MAINTENANCE ENGINEERING ORDER

(AMCOM Reg. 750-2)

MEO NO.

DATE PAGE 1 of

TITLE Tolerances Unless otherwise noted, dimensions are in inches and tolerances are:

Fractional ………………… ± 1/32 Decimal ………………... ± 0.010 Angular ………………… ± ½°

APPLICABILITY CSI Critical Characteristic Affected?

Impact Statement Attached?

REFERENCES FOR RDECOM USE ONLY

DOCUMENT(S) AFFECTED

PURPOSE OR PROBLEM

PROJECT ENGINEER ENGINEERING REVIEW ENGINEERING RELEASE

MED FORM 5-DEC-09 1401-R-E

AR 70-62 •11 May 2016 B 2939

Nov 21, 2017 3

COMPONENT DATA FORM UPDATE WP 0003

P/N 70250-12051-045, 70250-12051-048

Technical

INTERIM USE OF THIS MEO IS AUTHORIZED

UNTIL AFFECTED DOCUMENT IS UPDATED.

MEO CHANGE TYPE

3) High - Has a business or process impactPRIORITY IMPLEMENTATION CATEGORY

UH60 DAA

DMWR 1-1620-247 dated 21 JULY 2017 TN178585

DOCUMENT CHANGE IS REQUIRED Verification: Hands-On Table-Top None

Update component data form boilerplate.

KERNAN.JAMES.

J.JR.1258452760

Digitally signed by

KERNAN.JAMES.J.JR.1258452760

DN: c=US, o=U.S. Government, ou=DoD, ou=PKI, ou=USA, cn=KERNAN.JAMES.J.JR.1258452760 Date: 2017.11.15 07:09:18 -06'00'

ARREDONDO.M

ARCEL.MARCIAL

.1410770233

Digitally signed by

ARREDONDO.MARCEL.MARCIAL.1410770233

DN: c=US, o=U.S. Government, ou=DoD, ou=PKI, ou=CONTRACTOR, cn=ARREDONDO.MARCEL.MARCIAL.141077023 Date: 2017.11.14 12:57:02 -06'00'

Marcel Arredondo

HORN.REINHOL

D.J.1087783495

Digitally signed by

HORN.REINHOLD.J.1087783495

DN: c=US, o=U.S. Government, ou=DoD, ou=PKI, ou=USA, cn=HORN.REINHOLD.J.1087783495 Date: 2017.11.15 10:22:52 -06'00'

James Kernan Ron Horn PUBLICATION CHANGE REQUEST: REQUEST THAT THE FOLLOWING DATA BE INCLUDED IN THE NEXT

CHANGE OR REVISION TO THE PUBLICATION IDENTIFIED ABOVE.

WP NO. PAGE

NO.

PARA-

GRAPH

FIGURE/

TABLE

NO.

CHANGES

(EXACT WORDING OF CHANGES MUST BE GIVEN)

Figure 3

Distribution Statement D:- Distribution authorized to Department of Defense and U.S. DoD contractors only to protect critical technology effective as of 26 June 2014. Other requests for this document must be referred to U.S. Army Aviation and Missile Research, Development and Engineering Center, ATTN: RDMR -AEM , Corpus Christi, TX 78419-5211

CHANGE the Component Data Form section as shown on page 2 of this

MEO.

CHANGE Figure 3, Sheet 2 of 2 as shown on page 3 of this MEO.

MED FORM 04 APR 2017

Continuation Sheet

MEO NO.

PAGE of

MED FORM 15-DEC-09 1401-R-E

AR 70-62 •11 May 2016 2

Component Data Form

Complete an electronic Component Data Form (CDF) in the Apps tab, available at TAMMS-A/MCDS (WP 0053, Websites). One CDF is required for each assembly repaired or overhauled. The CDF application allows a user to enter the component data of the part being serviced and related subcomponent data. Associated documentation and photos can also be uploaded as PDF or image formats.

The CDF is initiated during the PSA process. Once on the CDF application, enter the P/N and S/N of the assembly, then enter the assembly information. Next, below the assembly information, in the ACTUAL COMPONENT FAILURES section, add any individual parts that failed.

The CDF can be edited later to add additional parts that fail during the repair or overhaul cycle. The facility must set up their system to capture all failed parts throughout the entire repair or overhaul process.

A copy of the Component Data Form (AMSAM-MMC Form 723, 1 July 06) is included in this WP if a working paper copy is needed.

MED FORM 04 APR 2017

B 2939

Continuation Sheet

MEO NO.

PAGE of

MED FORM 15-DEC-09 1401-R-E

AR 70-62 •11 May 2016

MED FORM 04 APR 2017

B 2939