Attachment 0005_MEO B2930.pdf

MAINTENANCE ENGINEERING ORDER

(AMCOM Reg. 750-2)

MEO NO.

DATE PAGE 1 of

TITLE Tolerances Unless otherwise noted, dimensions are in inches and tolerances are:

Fractional ………………… ± 1/32 Decimal ………………... ± 0.010 Angular ………………… ± ½°

APPLICABILITY CSI Critical Characteristic Affected?

Impact Statement Attached?

REFERENCES FOR RDECOM USE ONLY

DOCUMENT(S) AFFECTED

PURPOSE OR PROBLEM

PROJECT ENGINEER ENGINEERING REVIEW ENGINEERING RELEASE

MED FORM 5-DEC-09 1401-R-E

AR 70-62 •11 May 2016 B 2930

Sep 21, 2017 1

FPI Process Update WP 0009 P/N 70250-12051-045

Technical

INTERIM USE OF THIS MEO IS AUTHORIZED

UNTIL AFFECTED DOCUMENT IS UPDATED.

MEO CHANGE TYPE

3) High - Has a business or process impactPRIORITY IMPLEMENTATION CATEGORY

UH60 DAA

DMWR 1-1620-247 dated 21 July 2017 TN168974A, 177671

DOCUMENT CHANGE IS REQUIRED Verification: Hands-On Table-Top None

Update the FPI process.

KERNAN.JAMES.

J.JR.1258452760

Digitally signed by

KERNAN.JAMES.J.JR.1258452760

DN: c=US, o=U.S. Government, ou=DoD, ou=PKI, ou=USA, cn=KERNAN.JAMES.J.JR.1258452760 Date: 2017.09.13 10:45:08 -05'00'

SALAZAR.ALBER

TO.JAIME.12571

46258

Digitally signed by

SALAZAR.ALBERTO.JAIME.1257146258

DN: c=US, o=U.S. Government, ou=DoD, ou=PKI, ou=CONTRACTOR, cn=SALAZAR.ALBERTO.JAIME.12571462 Date: 2017.09.13 10:31:04 -05'00'

A.J. SALAZAR (CAMBER)

HORN.REINHOL

D.J.1087783495

Digitally signed by

HORN.REINHOLD.J.1087783495

DN: c=US, o=U.S. Government, ou=DoD, ou=PKI, ou=USA, cn=HORN.REINHOLD.J.1087783495 Date: 2017.09.13 14:54:43 -05'00'

JAMES KERNAN RON HORN

PUBLICATION CHANGE REQUEST: REQUEST THAT THE FOLLOWING DATA BE INCLUDED IN THE NEXT

CHANGE OR REVISION TO THE PUBLICATION IDENTIFIED ABOVE.

WP NO. PAGE

NO.

PARA-

GRAPH

FIGURE/

TABLE

NO.

CHANGES

(EXACT WORDING OF CHANGES MUST BE GIVEN)

0009 CHANGE the FPI PROCEDURES section to read:

"All fluorescent penetrant parts listed in applicable OIPs shall be inspected 100% of inspectable areas (unless otherwise specified by DMWR) per ASTM-E1417, Type I, Method A, C, or D, with sensitivity level 3 or higher, as applicable. Inspection method for each part shall be incorporated into locally developed non-destructive inspection procedure as specified in ASTM E1417 and approved by NAS 410 Level III. Technicians performing inspection shall be certified per NAS 410. Only Qualified Penetrant materials in QPL-AMS-2644 shall be used in performance of inspection."

Distribution Statement D:- Distribution authorized to Department of Defense and U.S. DoD contractors only to protect critical technology effective as of 26 June 2014. Other requests for this document must be referred to U.S. Army Aviation and Missile Research, Development and Engineering Center, ATTN: RDMR -AEM , Corpus Christi, TX 78419-5211

MED FORM 04 APR 2017