Attachment 0002_MEO B2914.pdf

MAINTENANCE ENGINEERING ORDER

(AMCOM Reg. 750-2)

MEO NO.

DATE PAGE 1 of

TITLE Tolerances Unless otherwise noted, dimensions are in inches and tolerances are:

Fractional ………………… ± 1/32 Decimal ………………... ± 0.010 Angular ………………… ± ½°

APPLICABILITY CSI Critical Characteristic Affected?

Impact Statement Attached?

REFERENCES FOR RDECOM USE ONLY

DOCUMENT(S) AFFECTED

PURPOSE OR PROBLEM

PROJECT ENGINEER ENGINEERING REVIEW ENGINEERING RELEASE

MED FORM 5-DEC-09 1401-R-E

AR 70-62 •11 May 2016 B 2914

Sep 21, 2017 6

IUID Parts Marking Updates for UH60 Main Landing Gear Shock Strut Assembly P/N 70250-12051-042 thru -45, -048

Technical

INTERIM USE OF THIS MEO IS AUTHORIZED

UNTIL AFFECTED DOCUMENT IS UPDATED.

MEO CHANGE TYPE

3) High - Has a business or process impactPRIORITY IMPLEMENTATION CATEGORY

UH60 DAA

DMWR 1-1620-247 dated 20 July 2017 TN 177881 8/30/2017

DOCUMENT CHANGE IS REQUIRED Verification: Hands-On Table-Top None

Changes based on DMWR IUID MEO Review (TN 177671).

KERNAN.JAMES.

J.JR.1258452760

Digitally signed by

KERNAN.JAMES.J.JR.1258452760

DN: c=US, o=U.S. Government, ou=DoD, ou=PKI, ou=USA, cn=KERNAN.JAMES.J.JR.1258452760 Date: 2017.09.07 08:21:34 -05'00'

NOLEN.OTIS.

F.1231157146

Digitally signed by

NOLEN.OTIS.F.1231157146

DN: c=US, o=U.S. Government, ou=DoD, ou=PKI, ou=CONTRACTOR, cn=NOLEN.OTIS.F.1231157146 Date: 2017.09.05 07:56:15 -05'00'

Otis Nolen

HORN.REINHOL

D.J.1087783495

Digitally signed by

HORN.REINHOLD.J.1087783495

DN: c=US, o=U.S. Government, ou=DoD, ou=PKI, ou=USA, cn=HORN.REINHOLD.J.1087783495 Date: 2017.09.07 17:27:34 -05'00'

James Kernan Ron Horn PUBLICATION CHANGE REQUEST: REQUEST THAT THE FOLLOWING DATA BE INCLUDED IN THE NEXT

CHANGE OR REVISION TO THE PUBLICATION IDENTIFIED ABOVE.

WP NO. PAGE

NO.

PARA-

GRAPH

FIGURE/

TABLE

NO.

CHANGES

(EXACT WORDING OF CHANGES MUST BE GIVEN)

4.b

Distribution Statement D:- Distribution authorized to Department of Defense and U.S. DoD contractors only to protect critical technology effective as of 26 June 2014. Other requests for this document must be referred to U.S. Army Aviation and Missile Research, Development and Engineering Center, ATTN: RDMR -AEM , Corpus Christi, TX 78419-5211

DELETE sentence prior to DOD IUID REGISTRY QUERY.

REPLACE in the DOD IUID REGISTRY QUERY section, 4.b to read:

"Using the human readable manufacturer serial number on the component (indicated by Serial No., Ser No., S/N, SN, SER, (S), SEQ, etc.), query the DoD IUID Registry. Select “Queries,” then “Pedigree Query.” Place the human readable manufacturer serial number in the “Serial Number” field. The query may return multiple records. Use the additional data from the component (component description, part number, etc.) to determine if one of the registry records can be matched to the component. If a registry record's data matches the component data exactly, proceed to Step 6. If no registry record can be matched exactly to the component data, proceed to Step 4.c below."

MED FORM 04 APR 2017

Continuation Sheet

MEO NO.

PAGE of

WP NO. PAGE

NO.

PARA-

GRAPH

FIGURE/

TABLE

NO.

CHANGES

(EXACT WORDING OF CHANGES MUST BE GIVEN)

MED FORM 15-DEC-09 1401-R-E

4.c

ADD 4.c to read:

"Using the human readable manufacturer serial number on the component (indicated by Serial No., Ser No., S/N, SN, SER, (S), SEQ, etc.), query the DoD IUID Registry. Select “Queries,” then “Mark Query.”

Place “SERIAL NUMBER” in the “Mark Content” field and place the human readable manufacturer serial number (as visible on component, minus any spaces) in the “Mark Value” field. The query may return multiple records. Use the additional data from the component (component description, part number, etc.) to determine if one of the registry records can be matched to the component. If a registry record’s data matches the component data exactly, proceed to Step 6. If no registry record can be matched exactly to the component data, indicate on local documents that the component was not found in the DoD IUID Registry (i.e., did not have a registered UII). New IUID data plates shall be fabricated IAW WP 0005 00, IUID Data Plate Fabrication."

DELETE in IUID LIFE CYCLE EVENT (LCE)

"...at https://tamms-a.redstone.army.mil,..."

DELETE in IUID PARENT CHILD RELATIONSHIP

DELETE in PART NUMBER CONFIGURATION CHANGE

MED FORM 04 APR 2017

AR 70-62 •11 May 2016

B 2914

Continuation Sheet

MEO NO.

PAGE of

WP NO. PAGE

NO.

PARA-

GRAPH

FIGURE/

TABLE

NO.

CHANGES

(EXACT WORDING OF CHANGES MUST BE GIVEN)

MED FORM 15-DEC-09 1401-R-E

Table 1 CHANGE for Abandoned Event, the beginning of the last sentence of the Definition to read: "An item has no commercial value..."

CHANGE in the Manufacturer IUID Data Plate section two issues:

"(manufacturer?s CAGE Code)" to read: (manufacturer's CAGE Code)"

AND

"(manufacturer?s serial number) to read: "(manufacturer's serial number)"

CHANGE in Legacy IUID Data Plate section:

"(supplier?s CAGE code)" to read: "(supplier's CAGE code)"

MED FORM 04 APR 2017

AR 70-62 •11 May 2016

Continuation Sheet

MEO NO.

PAGE of

WP NO. PAGE

NO.

PARA-

GRAPH

FIGURE/

TABLE

NO.

CHANGES

(EXACT WORDING OF CHANGES MUST BE GIVEN)

MED FORM 15-DEC-09 1401-R-E

1.a

1.c

REPLACE in the IUID DATA PLATE FABRICATION section, para. 1.a to read:

"A Construct 1 UII shall be encoded into a 2-D data matrix using TEIs SPL (supplier’s CAGE Code) and UCN (supplier’s Unique Component Number), IAW DoD Guide to Uniquely Identifying Items and/or MIL-STD-130 and registered in the DoD IUID Registry via the Wide Area Work Flow e-Business Suite (WAWF) or The Army Maintenance Management System – Aviation/Maintenance Consolidated Database System (TAMMS-A/MCDS), Unique Identification (UID) database. The UII can be constructed by the overhaul/repair facility using the overhaul facility's Enterprise Identifier (CAGE) SPL and UCN or the overhaul facility can generate the UII via AMCOM’s The Army Maintenance Management System – Aviation/Maintenance Consolidated Database System (TAMMS-A/MCDS) UID database. The component's serially-managed manufacturer serial number shall not be used to develop the UII, but shall reside as HRI on the IUID data plate.

CHANGE in the IUID DATA PLATE FABRICATION section, para. 1.c:

"..http://www.acq.osd.mil/dpap/pdi/uid/data_submission_information.html ..." to read: "DPAP UID (Defense Procurement and Acquistion Policy)."

CHANGE in the IUID DATA PLATE FABRICATION section, para. 2 beginning of the first sentence to read: "If the Main Landing Gear Shock Strut Assembly has no IUID data plate present, however,..."

CHANGE in the IUID DATA PLATE FABRICATION section in Note prior to para. 4: "...per Step 5." to read: "...IUID DATA PLATE APPLICATION Step 6."

MED FORM 04 APR 2017

AR 70-62 •11 May 2016

Continuation Sheet

MEO NO.

PAGE of

WP NO. PAGE

NO.

PARA-

GRAPH

FIGURE/

TABLE

NO.

CHANGES

(EXACT WORDING OF CHANGES MUST BE GIVEN)

MED FORM 15-DEC-09 1401-R-E

Figure 1

Figure 2, (Sheet 1 of 2)

Figure 2, (Sheet 2 of 2)

REPLACE Figure 1 with figure found on page 6 of this MEO.

CHANGE in Note 2 first sentence: "..., the UII shall be replaced..."

to read: "..., the IUID data plate shall be replaced..."

CHANGE in Note 13 "...only utilized/installed when..."

to read: "...only encoded and displayed as HRI when..."

MED FORM 04 APR 2017

AR 70-62 •11 May 2016

Continuation Sheet

MEO NO.

PAGE of

MED FORM 15-DEC-09 1401-R-E

AR 70-62 •11 May 2016

Figure 1. Main Landing Gear Shock Assembly, 70250-12051-044, 045 and 048 Data Plates.

MED FORM 04 APR 2017